Section 2. Pipe, Valves and Fittings Sizes ¼" to 12" Schedule 80 CPVC Piping System. Serviced by GF Little Rock
|
|
|
- Pamela Greer
- 5 years ago
- Views:
Transcription
1 Section 2 Schedule 80 CPVC Piping System Pipe, Valves and Fittings Sizes ¼" to 12" Serviced by GF Little Rock Effective March 27, 2006
2 Glossary Std. Pack = Standard Carton Quantity FP = Female Pipe hread MP = Male Pipe hread S = apered Socket SPG = Spigot End (same dimension as pipe outside diameter) * = Non-Returnable / Non-cancellable ^ = 40% Restocking Fee HS = High Strength Design SL = Streamline Design XXXX-XXXFB = Assembled Fitting from Molded Components XXXX-XXXH = Fabricated Fitting Product Line Descriptions Discount 70 CPVC Pressure Pipe-20ft. Lengths Plain End 25 CPVC Pressure Fittings - Molded 34 CPVC Pressure Expansion Joint 33 CPVC Pressure Brass Insert Fittings 02 CPVC Pressure LD Fittings - Molded 06 CPVC Pressure LD Fittings - Fabricated 38 CPVC ype 546 rue Union Ball Valve 15 CPVC ype 375 rue Union Ball Valve 74 CPVC ype 567 Butterfly Valve he technical information given in this publication implies no warranty of any kind and is subject to change without notice. Please consult our erms and Conditions of Sale. Not for Use with Compressed Air or Gases DO NO ES with Air or Air over Water GF Piping DOES NO RECOMMEND the use of thermoplastic piping products for systems to transport or store compressed air or gases, or the testing of thermoplastic piping systems with compressed air or gases in above or below ground locations. he use of GF Piping products in compressed air or gas systems automatically voids the warranty for such products, and their use against our recommendation is entirely the responsibility and liability of the installer. GF Piping will not accept responsibility for damage or impairment from its products, or other consequential or incidental damages caused by misapplication, incorrect assembly, and/or exposure to harmful substances or conditions. For more information about any of our product lines, please call (800)
3 able of Contents Schedule 80 CPVC Piping System Specifications, Standards and olerances 2.4 Schedule 80 CPVC Pipe (½"-12") 2.5 Fittings (¼"-8") Molded 2.6 Expansion Joint 2.18 Brass Insert 2.19 Large Diameter Fittings (10"-12") Pressure Large Diameter Molded 2.20 Pressure Large Diameter Fabricated 2.21 Manual Valves ype 546 and ype 375 ball valves 2.25 ype 567 butterfly valve 2.26 Specification Submittal Data Sheet
4 Specifications, Standards and olerances Specifications and Standards NSF/ANSI Standard 14 NSF/ANSI Standard 61 ASM D 1784 : Material CPVC ype IV, Grade I Gray (cell classification B) ASM F 441 : CPVC Schedule 80 Pipe ASM F 439 : CPVC Schedule 80 Socket & hreaded Fittings ASM F 437 : CPVC Schedule 80 hreaded Fittings ASM F 1970 : CPVC Schedule 80 Unions & Flanges ANSI B16.5 : Flange Bolt Hole Patterns ANSI B : CPVC Schedule 80 NP hreads CSA B137.6 : CPVC Schedule 80 Pipe (1¼ - 2½ only) Molded Dimension olerances A Piston Position; Expansion Joints : ±0.03 D Outside Diameter : ± 0.06 G, G1 Intersections of centerlines to bottom of socket; 90 Ells, ees : up to 4" ±0.03; 6" and above ±0.06 GJ, GN Intersections of centerlines to bottom of socket; 45 Wyes : up to 4" ±0.03; 6" and above ±0.06 H, HJ, HN Intersections of centerlines to face of fitting; 90 Ells, 45 Ells, ees, 45 Wyes : up to 4" ±0.03; 6" and above ±0.06 HL Socket Bottom to Face of Fitting : up to 4" ±0.03; 6" and above ±0.06 J Intersections of centerlines to bottom of socket; 45 & 30 Ells : up to 4" ±0.03; 6" and above ±0.06 L Overall Length of fitting : ± 0.06 N Socket Bottom to Socket Bottom; Couplings, Unions : ± 0.06 N1 Socket Bottom to Face of Flange : ± 0.06 R hickness on Plugs, Flanges : ± 0.03, 1 Effective hread Length : Reference Only W Height of Cap : ± 0.06 Fabricated Dimension olerances D Outside Diameter : ± 0.50 E Drive Pin Diameter : ± 0.50 G, G1 Intersections of centerlines to bottom of socket; 90 Ells, ees, Crosses : ± 0.25 GJ, GN Intersections of centerlines to bottom of socket; 45 Wyes : ± 0.25 H, HJ, HN Intersections of centerlines to face of fitting; 90 Ells, 45 Ells, ees, 45 Wyes, rue Wyes : ± 0.50 HL Socket Bottom to Face of Fitting : ± 0.25 J Intersections of centerlines to bottom of socket; 11¼, 15, 30, 22½, 45 Ells, rue Wyes : ± 0.25 L Overall Length of fitting : ± 0.50 N Socket Bottom to Socket Bottom; Couplings : ± 0.50 N1 Socket Bottom to Face of Flange : ± 0.50 R hickness on Plugs, Flanges : ± 0.25, 1 Effective hread Length : Reference Only W Height of Cap : ±
5 Schedule 80 CPVC Pressure Pipe P/L 70 : CPVC Pressure Pipe - 20 ft. lengths Plain End Size Part Number Plain End List $/100 ft. Lift Qty (ft.) Average O.D. Min. Wall ½ *C AB See Note 5600 ft ¾ *C AB " 5000 ft *C AB " 2360 ft ¼ *C AB " 1960 ft ½ *C AB " 1800 ft *C AB " 1060 ft ½ *C AB " 880 ft *C AB " 700 ft *C AB " 520 ft *C AB " 220 ft *C AB " 100 ft *C AB " 80 ft *C AB " 60 ft psi at 73 F Schedule 80 CPVC Note: For current pricing information please see separate price sheet or visit our website at ^ = 40% Restock Charge 2.5
6 Schedule 80 CPVC Pressure Fittings P/L 25 : CPVC Pressure Fittings - Molded ee (S x S x S) Size Part $ List/ea. Std Pack H G Design Number ½ SL ¾ SL SL 1¼ SL 1½ SL SL 2½ HS HS HS HS HS Reducing ee (S x S x S) Size Part Number $ List/ea. Std HJ HN G G1 Design Pack ¾x½ SL 1x½ SL 1x¾ SL 1¼x SL 1½x½ SL 1½x¾ SL 1½x SL 2x½ SL 2x¾ SL 2x SL 2x1½ SL 2½x SL 3x SL 4x SL 4x SL 6x2 * FB HS 6x3 * FB HS 6x HS 8x HS HS = High Strength Design SL = Slim Line Design ^ = 40% Restock Charge 2.6
7 ee (FP x FP x FP) Size Part Number List $/ea. Std. Pack H Design ¼ ^ HS 3/ 8 ^ HS ½ ^ HS ¾ ^ HS H 1 ^ HS 1¼ ^ HS 1½ ^ HS 2 ^ HS 2½ ^ HS 3 ^ HS 4 ^ HS Schedule 80 CPVC 90 Ell (S x S) Size Part Number List $/ea. Std. Pack H G Design ¼ HS 3/ HS ½ SL ¾ SL SL 1¼ SL 1½ SL SL 2½ SL HS HS SL HS HN G HJ 90 Ell (S x FP) Size Part Number List $/ea. Std. Pack HJ HN G Design ½ HS ¾ HS HS 90 Ell (FP x FP) Size Part Number List $/ea. Std. Pack H Design ¼ ^ HS 3/ 8 ^ HS ½ ^ HS H ¾ ^ HS 1 ^ HS 1¼ ^ HS 1½ ^ HS 2 ^ HS 2 ½ ^ HS 3 ^ HS 4 ^ HS 2.7
8 45 Ell (S x S) Size Part Number List $/ea. Std. Pack H J Design ¼ HS 3/ HS ½ SL ¾ SL SL 1¼ SL 1½ SL SL 2½ HS SL SL HS HS H 45 Ell (FP x FP) Size Part Number List $/ea. Std. Pack H Design ¼ ^ HS 3/ 8 ^ HS ½ ^ HS ¾ ^ HS 1 ^ HS 1¼ ^ HS 1½ ^ HS 2 ^ HS 3 ^ HS 4 ^ HS Coupling (S x S) Size Part Number List $/ea. Std. Pack L N Design ¼ HS 3/ HS ½ SL ¾ SL SL 1¼ SL 1½ SL SL 2½ HS SL SL HS HS HS = High Strength Design SL = Slim Line Design ^ = 40% Restock Charge 2.8
9 Reducing Coupling (S x S) Size Part Number List $/ea. Std. L N Design Pack ¾ x ½ HS 1 x ½ HS 1 x ¾ HS 1½ x ½ * FB HS 1½ x ¾ * FB HS 1½ x HS 1½ x 1¼ HS 2 x ½ * FB HS 2 x ¾ * FB HS 2 x HS 2 x 1¼ * FB HS 2 x 1½ HS 2½ x 1½ HS 3 x HS 4 x 2 * FB HS 4 x HS 6 x HS 8 x HS Schedule 80 CPVC L Coupling (FP x FP) Size Part Number List $/ea. Std. Pack L Design ¼ ^ HS 3/ 8 ^ HS ½ ^ HS ¾ ^ HS 1 ^ HS 1¼ ^ HS 1½ ^ HS 2 ^ HS 3 ^ HS 4 ^ HS 1 Reducing Coupling (FPxFP) Size Part Number List $/ea. Std. Pack L 1 Design ½ x ¼ ^ HS ½ x 3 / 8 ^ HS ¾ x ½ ^ HS 1 x ½ ^ HS 1 x ¾ ^ HS 1½ x 1 ^ HS L 2.9
10 HL Female Adapter (SxFP) Size Part Number List $/ea. Std. Pack HL L Design ¼ HS ½ HS ¾ HS HS 1¼ HS 1½ HS HS HS HS L Male Adapter (SxMP) Size Part Number List $/ea. Std. Pack HL L Design ½ HS ¾ HS HS 1¼ HS 1½ HS HS HS HS Flush Style Reducer Bushing (SpgxS) Size Part Number List $/ea. Std. Pack HL L ½ x ¼ ½ x 3 / ¾ x ½ x ½ x ¾ ¼ x ½ ¼ x ¾ ¼ x ½ x ½ ½ x ¾ ½ x ½ x 1¼ x ½ x ¾ x x 1¼ x 1½ ½ x 1½ ½ x x 1½ x x 2½ x x x x x
11 Flush Style Reducer Bushing (SpgxFP) Size Part Number List $/ea. Std. Pack L ½ x ¼ ½ x 3 / ¾ x ¼ ¾ x ½ L 1 x ½ x ¾ ¼ x ½ ¼ x ¾ ¼ x ½ x ½ ½ x ¾ ½ x ½ x 1¼ x ½ x ¾ x x 1¼ x 1½ ½ x 1½ ½ x x x x Schedule 80 CPVC Flush Style Reducer Bushing (MPxFP) Size Part Number List $/ea. Std. Pack L 3/ 8 x ¼ ^ ½ x ¼ ^ L ½ x 3 / 8 ^ ¾ x 3 / 8 ^ ¾ x ½ ^ x ½ ^ x ¾ ^ ¼ x 1 ^ ½ x ¾ ^ ½ x 1 ^ ½ x 1¼ ^ x 1 ^ x 1¼ ^ x 1½ ^ ^ = 40% Restock Charge 2.11
12 Cap (S) Size Part Number List $/ea. Std. Pack W Design ½ HS ¾ HS HS 1¼ HS 1½ HS HS 2½ HS HS HS HS HS Plug (Spg) Size Part Number List $/ea. Std. Pack L R ½ ¾ 1 1½ 2 4 W Cap (FP) Size Part Number List $/ea. Std. Pack W Design ¼ ^ HS 3/ 8 ^ HS ½ ^ HS ¾ ^ HS 1 ^ HS 1¼ ^ HS 1½ ^ HS 2 ^ HS Plug (MP) Size Part Number List $/ea. Std. Pack L R ¼ / ½ ¾ ½ ½
13 Flange (S) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L N1 R ½ ½ ¾ ½ ½ ¼ ½ ½ ½ / ½ / / / ¾ Schedule 80 CPVC L R D Flange (FP) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L R ½ ^ ½ ¾ ^ ½ ^ ½ ¼ ^ ½ ½ ^ ½ ^ / ^ / ^ / Flange (Blind) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L R ½ ½ ¾ ½ ½ ¼ ½ ½ ½ / / / ¾ ¾ ^ = 40% Restock Charge 2.13
14 Van Stone Flange (S) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L N1 R ½ ½ ¾ ½ ½ ¼ ½ ½ ½ / ½ / / / ¾ ¾ L R D Van Stone Flange (FP) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L R 1 ^ ½ ¼ ^ ½ ½ ^ ½ ^ / Van Stone Flange (Spg) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L R ½ ½ ¾ ½ ½ ¼ ½ ½ ½ / ½ / / / ^ = 40% Restock Charge 2.14
15 ^ = 40% Restock Charge Nipple (mpt x mpt) Size Part Number List $/ea. Std. Pack L ½ x CL * ½ x SH * ½ x 2 * ½ x 3 * ½ x 4 * ½ x 5 * ½ x 6 * ¾ x CL * ¾ x 2 * ¾ x 3 * ¾ x 4 * ¾ x 5 * ¾ x 6 * x CL * x SH * x 3 * x 4 * x 5 * x 6 * ¼ x CL * ¼ x SH * ¼ x 3 * ¼ x 4 * ¼ x 5 * ¼ x 6 * ½ x CL * ½ x SH * ½ x 3 * ½ x 4 * ½ x 5 * ½ x 6 * x CL * x SH * x 3 * x 4 * x 5 * x 6 * ½ x CL * ½ x SH * ½ x 4 * ½ x 5 * ½ x 6 * x CL * x SH * x 4 * x 5 * x 6 * x CL * x SH * x 5 * x 6 * Schedule 80 CPVC 2.15
16 45 Wye (SxSxS) Size Part Number List $/ea. Std. Pack GJ GN H HJ L N Design 1½ * HS 2 * HS SL SL HS 6 x HS Rated 150psi at 73 F Union (SxS) Size Part Number List $/ea. Std. Pack L N ¼ / ½ ¾ ¼ ½ O-Ring Material: EPDM Union (FPxFP) Size Part Number List $/ea. Std. Pack L 3/ 8 ^ ½ ^ ¾ ^ ^ ¼ ^ ½ ^ ^ ^ ^ O-Ring Material: EPDM L HS = High Strength Design SL = Slim Line Design ^ = 40% Restock Charge 2.16
17 Union (SxS) Size Part Number List $/ea. Std. Pack L N ¼ / ½ ¾ ¼ ½ O-Ring Material: FPM Schedule 80 CPVC Union (FPxFP) Size Part Number List $/ea. Std. Pack L 3/ 8 ^ ½ ^ ¾ ^ ^ ¼ ^ ½ ^ ^ ^ ^ O-Ring Material: FPM L ^ = 40% Restock Charge 2.17
18 Schedule 80 CPVC Expansion Joint P/L 34 : CPVC Pressure Expansion Joint Flanged, spigot and threaded ends available. Contact factory for pricing and availability. Expansion Joint 6 ravel (SxS) Size Part Number List $/ea. Std. Pack A D L N ½ * X ¾ * X * X ¼ * X ½ * X * X * X * X * X O-Ring Material: EPDM Expansion Joint 12 ravel (SxS) Size Part Number List $/ea. Std. Pack A D L N ½ * X ¾ * X * X ¼ * X ½ * X * X * X * X * X O-Ring Material: EPDM Expansion Joint 6 ravel (SxS) Size Part Number List $/ea. Std. Pack A D L N ½ * X ¾ * X * X ¼ * X ½ * X * X * X * X * X6 1, O-Ring Material: FPM ^ = 40% Restock Charge Expansion Joint 12 ravel (SxS) Size Part Number List $/ea. Std. Pack A D L N ½ * X ¾ * X * X ¼ * X ½ * X * X * X * X12 1, * X12 1, O-Ring Material: FPM 2.18
19 Schedule 80 CPVC Brass Insert Fittings P/L 33 : CPVC Pressure Brass Insert Fittings G ee (SxSxFP Brass) HN HJ G HJ Size Part Number List $/ea. Std. Pack HJ HN G ½ * ¾ x ½ * Ell (S x FP Brass) Schedule 80 CPVC Size Part Number List $/ea. Std. Pack HJ HN G ½ * HN ¾ x ½ * HL Coupling (SxFP Brass) Size Part Number List $/ea. Std. Pack HL L ½ * ¾ x ½ * L Male Adapter (SxMP Brass) Size Part Number List $/ea. Std. Pack HL L ½ * ¾ * * ^ = 40% Restock Charge 2.19
20 Schedule 80 CPVC Large Diameter Fittings P/L 02 : CPVC Pressure LD Fittings - Molded ee (SxSxS) Size Part Number List $/ea. Std. Pack H G , , Reducing ee (SxSxS) Size Part Number List $/ea. Std. Pack HJ HN G G1 10 x 8 * FB 2, x 10 * FB 3, Ell (SxS) Size Part Number List $/ea. Std. Pack H G Ell (SxS) Size Part Number List $/ea. Std. Pack H J Flush Style Reducer Bushing (SpgxS) Size Part Number List $/ea. Std. Pack HL L 10 x x Cap (S) Size Part Number List $/ea. Std. Pack W Van Stone Flange (S) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Circle D L N1 R / , /
21 Schedule 80 CPVC Large Diameter Fittings P/L 06 : CPVC Pressure LD Fittings - Fabricated Reducing ee (SxSxS) Size Part Number List $/ea. Std. HJ HN G G1 Pack 10 x 2 * H 1, x 3 * H 1, x 4 * H 1, x 6 * H 1, x 2 * H 1, x 3 * H 2, x 4 * H 2, x 6 * H 2, x 8 * H 2, Schedule 80 CPVC 11¼ Ell (SxS) Size Part Number List $/ea. Std. Pack H J 10 * H * H 1, Ell (SxS) Size Part Number List $/ea. Std. Pack H J 10 * H 1, * H 1, ½ Ell (SxS) Size Part Number List $/ea. Std. Pack H J 10 * H * H 1, Ell (SxS) Size Part Number List $/ea. Std. Pack H J 10 * H 1, * H 1, Cross (SxSxSxS) Size Part Number List $/ea. Std. Pack H J 10 * H 2, * H 2,
22 Reducing Cross (SxSxSxS) Size Part Number List $/ea. Std. Pack HJ HN G G1 10 x 2 * H 1, x 3 * H 1, x 4 * H 1, x 6 * H 2, x 8 * H 2, x 2 * H 1, x 3 * H 1, x 4 * H 2, x 6 * H 2, x 8 * H 3, x 10 * H 4, Coupling (SxS) Size Part Number List $/ea. Std. Pack L N 10 * H * H 1, Reducing Coupling (SxS) Size Part Number List $/ea. Std. Pack L N 10 x 4 * H x 6 * H x 8 * H x 8 * H 1, x 10 * H 1, HL L Female Adapter (SxFP) Size Part Number List $/ea. Std. Pack HL L 6 * H * H * H * H Male Adapter (SxMP) Size Part Number List $/ea. Std. Pack HL L 6 * H * H * H * H ^ = 40% Restock Charge 2.22
23 Flush Style Reducer Bushing (SpgxS) Size Part Number List $/ea. Std. Pack HL L 10 x 4 * H 1, x 6 * H x 6 * H 1, x 8 * H L Flush Style Reducer Bushing (SpgxFP) Size Part Number List $/ea. Std. Pack L 10 x 6 * H 1, x 8 * H 1, x 8 * H 2, x 10 * H 2, Schedule 80 CPVC Extended Style Reducer Bushing (SpgxS) Size Part Number List $/ea. Std. Pack D HL L 10 x 6 * H 1, x 8 * H x 8 * H 1, x 10 * H 1, Eccentric Reducer (SxS) Size Part Number List $/ea. Std. Pack L N 10 x 4 * H 1, x 6 * H 1, x 8 * H 1, x 6 * H 1, x 8 * H 1, x 10 * H 2, Plug (MP) Size Part Number List $/ea. Std. Pack E L 6 * H * H * H * H Flange (Blind) Size Part Number List $/ea. Std. Pack # of Holes Bolt Bolt Corcle 10 * H / * H 1, / D R 2.23
24 45 Wye (SxSxS) Size Part Number List $/ea. Std. GJ GN H HJ L N Pack 10 * H 2, * H 3, Reducing 45 Wye (SxSxS) Size Part Number List $/ea. Std. Pack GJ GN H HJ L N 10 x 2 * H x 3 * H x 4 * H 1, x 6 * H 1, x 8 * H 1, x 2 * H 1, x 3 * H 1, x 4 * H 1, x 6 * H 1, x 8 * H 2, x 10 * H 2, ^ = 40% Restock Charge 2.24
25 Manual Ball Valves P/L 38 : ype 546 rue Union Ball Valve-CPVC Solvent Cement Socket/hreaded NP Size Part Number/ $ List/ea. Part Number/ $ List/ea. EPDM Seals FPM Seals 3 / ½ ¾ ¼ ½ Schedule 80 CPVC ANSI Flanged Size Part Number/ $ List/ea. Part Number/ $ List/ea. ID Inch EPDM Seals FPM Seals ½ ¾ ¼ ½ P/L 15 : ype 375 rue Union Ball Valve-CPVC Socket/hreaded NP Size Part Number/ $ List/ea. Part Number/ $ List/ea. EPDM Seals FPM Seals ½ ¾ ¼ ½ ½ = 2½ - 6 includes socket only Flanged Size Part Number/ $ List/ea. Part Number/ $ List/ea. EPDM Seals FPM Seals ½ ¾ ¼ ½ ½
26 Manual Butterfly Valves P/L 74: ype 567 Butterfly Valve-CPVC Hand Lever with Ratchet Settings Connecting dimension: ISO 7005 PN 10, EN 1092 PN 10, DIN 2501 PN 10, ANSI B 16.5 Class 150, BS 1560: 1958, JIS B 2220 Overall length according to EN 558-1, ISO 5752 Inch PSI Cv EPDM List $/ea. FPM List $/ea ^ ^ ½ ^ ^ ^ ^ ^ ^ ^ ^ , ^ ^ , ^ ^ , Inch D D1 min D1 max d2 H H1 H2 H ½ Inch L L1 L2 Q1 Q ½ ^ = 40% Restock Charge 2.26
27 Manual Butterfly Valves P/L 74: ype 567 Butterfly Valve-CPVC Reduction Gear with Handwheel Connecting dimension: ISO 7005 PN 10, EN 1092 PN 10, DIN 2501 PN 10, ANSI B 16.5 Class 150, BS 1560: 1958, JIS B 2220 Overall length according to EN 558-1, ISO 5752 Schedule 80 CPVC Inch PSI Cv EPDM List $/ea. FPM List $/ea ^ ^ ½ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ , Inch D D1 min. D1 max. d2 D3 H H ½ Inch H2 H3 L L1 L2 L3 Q1 Q ½ ^ = 40% Restock Charge 2.27
28 George Fischer Piping Systems CPVC Pressure Piping System Specification Submittal Data Sheet Schedule 80 Pipe and Fittings Pipe: Pipe will be manufactured to the dimensions and tolerances of ASM F441. he CPVC material shall be ype I, Grade IV with a cell classification of B and conform to ASM D1784. he pipe will conform to NSF 14 & 61, CSA B137.6 (up to 4 ), and UPC standards q CPVC Sch.80 ype I, Group I Plain End Pipe - 20 ft. Lengths Fittings Socket type molded fittings will be manufactured to the dimensions and tolerances of ASM F439. hreaded type (NP) molded fittings will be manufactured to the dimensions and tolerances of ASM F437 and meet the requirements of ANSI/ ASME B Flanges shall meet the O.D. and bolt hole patterns as specified in ANSI/ASME B he CPVC material shall be ype I, Grade IV with a cell classification of B and conform to ASM D1784. he fittings will conform to NSF 14 & 61, and UPC standards. q q q CPVC Sch.80 ype I, Grade I Socket ype CPVC Sch.80 ype I, Grade I hreaded ype CPVC Sch.80 ype I, Grade I Flange ype Job Name: Job Location: Engineer: Contractor: Representative: 2.28
Section 12. Contain-It Secondary Containment Piping System. Serviced by GF Little Rock
Section 12 Contain-It Secondary Containment Piping System Serviced by GF Little Rock Table of Contents Contain-It Pipe 12.4 Fittings 12.5 Terminations 12.7 Centralizers 12.8 Accessories 12.9 Adhesive Requirements
SECTIO N 15 Phone: (866) Fax: (888)
PVC FITTINGS SCHEDULE 40, 80, INSERT NYLON FITTINGS PVC & CPVC NIPPLES SECTIO N 15 www.cbsupplies.ca Phone: (866) 503-5523 Fax: (888) 562-2095 AGI@cbsupplies.ca PRODUCTS LIST SCHEDULE 40 PVC PRESSURE FITTINGS
SCHEDULE 80 PVC PRESSURE FITTINGS L80P EFFECTIVE JULY 1, 2017 REVISED PRODUCTS PRICE LIST INCLUDES: SCHEDULE 80 PVC 1/4 TO 12
PRICE GROUP DESCRIPTION 02 SCH 80 PVC through 8 92 SCH 80 PVC 10" AND LARGER VB GASKET for FLANGE DISCOUNT MULTIPLIER PRODUCTS SCHEDULE 80 PVC PRESSURE FITTINGS INCLUDES: SCHEDULE 80 PVC 1/4 TO 12 L80P
PVC & CPVC Metric Fittings, Unions & Valves
ount (s): 019 Irrigation Manifolds 080 PVC Schedule 80 Molded Fittings Thru 8 190 PN16 PVC Metric Fittings 190 Class 10/12 PVC Metric Fittings 191 Metric PVC Molded 280mm & Larger 192 PN16 CPVC Metric
Pipe Nipples / Solvent Cement / Pipe Clips 11. Diaphragm Valves / Knife Gate Valves 21
TABLE OF CONTENTS Pipe Sizing 1 Pipe 2 Tee s 3 Elbows 4 Couplings 5 Adaptors, Caps & Plugs 6 Unions 7 Reducer Bushing 8 Wye s / Clamp on Saddles 9 Flanges 10 Pipe Nipples / Solvent Cement / Pipe Clips
Type Electrically Actuated Ball Valve
GF Piping Systems Electrically Actuated Ball Valve Type 179-184 General Size: ⅜ 4 Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seat: PTFE Seals: EPDM, FPM End Connection: Solvent cement
VT Series 3-Way Ball Valves Product Data Sheet. Valve Availability. Size Range: 1/2" through 2" EPDM or Viton (FPM)
Product Data Sheet < SANDARDS > introduction ASM D1784 ASM D4101-86 ASM D2466 ASM D2467 ASM D2464 ASM F1498 IPEX can be used for flow diverting, mixing, or on/off isolation. hey will replace a ee + 2 valve
TKD Series 3-Way Ball Valves Product Data Sheet
Product Data Sheet < SANDARDS > ASM D1784 ASM D2466 ASM D2467 ASM D2464 ASM F1498 introduction IPEX KD Series 3-Way Ball Valves can be used for flow diverting, mixing, or on/off isolation. hey will replace
standard and industrial pipe fittings
fittings mm sizes standard and industrial pipe fittings Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings from 6 bars to 16 bars,
True Union Ball Valve (BN) Product Category. Compact Ball. 2-pieces Compact Ball. Single Union Without Support. Ball Valve. True Union Without Support
Sekisui Industrial Piping Co., Ltd. located in the Chungkang Export Processing Zone of Taichung City in Taiwan. From March of 2006, Sekisui Industrial Piping Co., Ltd. was established as a wholly-owned
Schedule 80 - CPVC Pressure Fittings
Discount Codes 03 Schedule 80 CPVC Schedule 80 - CPVC Pressure Fittings List Prices L15-80C Effective: March 26, 2015 Revised 9.22.2016 2 Schedule 80 - CPVC Products Catalog www.lascofittings.com Pricing
industrial and economy pipe fittings PVC-U Solvent Cement WELD-ON REGULAR 719 Size Code Price 500ml tin
pvcu fittings mm sizes industrial and economy pipe fittings fittings mm sizes 68 Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings
Type 147. Electrically Actuated Lug Butterfly Valve
GF Piping Systems Electrically Actuated Lug Butterfly Valve Type 147 General Size: 2 12 Outer Body: Glass-filled PP Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seals: EPDM, FPM, PTFE/FPM
Fitting Guide. Chemtrol Thermoplastic Flow Solutions. Chemtrol is a brand of
Fitting Guide Thermoplastic Flow Solutions is a brand of Contents Introduction 2 Introduction to Fittings 2 Materials 2 Fitting Terms and Abbreviations 3 Dimensions and Standards 3 Product Guide 4 PVC
PVC 80, 100 & 125 PSI PIP Fabricated Fittings
Discount Code(s): 3 PVC 0 PSI PIP Fabricated Fittings PVC 0 PSI PIP Fabricated Fittings PVC 5 PSI PIP Fabricated Fittings PVC 0, 0 & 5 PSI PIP Fabricated Fittings Visit our web site: www.spearsmfg.com
Price List Effective March 19, 2012
Georg Fischer Harvel LLC 300 Kuebler Road Easton, PA 18040 USA Phone: (610) 252-7355 Fax: (610) 253-4436 harvel.gfh.ps@georgfischer.com www.harvel.com PRICES SUBJECT TO CHANGE WITHOUT NOTICE PRICE SHEET
DWV PVC DWV Drain Waste Vent Fittings
STANDARDS & SPECIFICATIONS Standards provide greater assurance of product performance and consistency, and are available to assist design engineers in system specification. The most frequently referenced
ABS DWV FITTINGS FOR PLUMBING AND MECHANICAL APPLICATIONS
ABS DWV FITTINGS FOR PLUMBING AND MECANICAL APPLICATIONS Job Name Contractor Job Location Wholesaler Engineer Streamline Rep Product Description: Streamline ABS DWV ittings for use in applications including
Type Electrically Actuated Ball Valve
Electrically Actuated Ball Valve Type 179-184 General Size: ⅜ 4 Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seat: PTFE Seals: EPDM, FPM End Connection: Solvent cement socket, threaded,
Advanced PE Single Wall Piping System
Advanced PE Single Wall Piping System 8 - Specification Black Polyethylene (Advanced PE) Piping System REV:IN0512PE Materials: Pipe Production: ASTM D3350 cell classification PE445584C. Resin shall comply
VR Piston Check Valves Submittal Data Sheet. Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: introduction
Submittal Data Sheet Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Date Date Date introduction < STANDARDS > The IPEX VR Piston Check Valve is an ideal solution
Discount Codes 07 DWV-PVC through 8 22 HVAC DWV - PVC. PVC Drain - Waste Vent Fittings. Includes: DWV - PVC - through 8 HVAC.
Discount Codes 07 DWV-PVC through 8 22 HVAC DWV - PVC PVC Drain - Waste Vent Fittings Includes: DWV - PVC - through 8 HVAC s Effective: March 14, 2011 1 H x FPT H x MPT SP x MPT SP x SJ w/plastic Nut &
PVC AND CPVC PRESSURE PIPES ASTM D-1785 and F-441 Schedule 80
2 PVC AN CPVC PRESSURE PIPES ASTM -1785 an F-441 Scheule 80 PVC ASTM 1785 SCHEULE 80 NOMINAL OUTSIE IAMETER PVC SCHEULE 80 WALL THICKNESS WORKING PRESSURE WEIGHT IN IN MM IN MM PSI @73F LB/FT 10022 1/8
LATEST ARRIVALS CATALOGUE STOCK
LATEST ARRIVALS CATALOGUE STOCK PIPES VALVES FLANGES & FITTINGS IN CARBON STEEL STAINLESS STEEL LATEST ARRIVALS!!!!!! VALVE PRODUCTS CAST IRON WAFER TYPE BUTTERFLY VALVE, PINLESS SHAFT, DUCTILE NICKEL
DK Series Dialock Manual Diaphragm Valves Product Data Sheet
< STANDARDS > ASTM D1784 ASTM D1785 ASTM D4101 ASTM D3222 ASTM D2464 ASTM D2467 ASTM D2466 ASTM F441 ASTM F437 ASTM F439 ASTM F1498 ISO 3609 ISO 10931 IPEX DK Series Dialock Diaphragm Valves are the ideal
Type 375. True Union Ball Valve
True Union Ball Valve Type 3 General Size: ⅜ 4 Material: PVC, CORZAN CPVC, or PPn Seat: PTFE Seals: EPDM or FPM End Connection: Solvent cement socket, threaded, flanged, PPro-Seal electrofusion socket
Praher S4 Ball Valve. manual valves. Materials. Sizes. Pressure Rating. Features. Connections. Valve Dimensions. Actuation.
Praher S4 Ball Valve Lockable Handle Tagging Point Valve Bracket Actuation Materials Body - PVDF Ball Seat - PTFE Seals - FPM Sizes 3/8-4 /16mm - 110mm Features Lockable Handle (Lock not supplied) True
Praher S4 Ball Valve. manual valves. Materials. Sizes. Pressure Rating. Features. Connections. Valve Dimensions. Actuation.
Praher S4 Ball Valve Lockable Handle Tagging Point Valve Bracket Actuation Materials Body - PVDF Ball Seat - PTFE Seals - FPM Sizes 3/8" - 4"/16mm - 110mm Features Lockable Handle (Lock not supplied) True
introduction VR Piston Check Valves Product Data Sheet
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D2466 ASTM D2467 ASTM D2464 ASTM F1498 The IPEX VR Piston Check Valve is an ideal solution for process back-flow prevention. These valves feature
ABS DWV FITTINGS MARCH 1, 2017
LIST U10-0317-IP ABS DWV FITTINGS MARCH 1, 2017 SUPERSEDES U10-1116-IP (NOVEMBER 1, 2016) Our website pricing is the current list price and may vary from our printed price list. Please visit our website
Type 567. Wafer Style Butterfly Valve
Wafer Style Butterfly Valve Type 5 General Size: 2 12 Outer Body: Glass-filled PP Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seals: EPDM, FPM, PTFE/FPM Stem: 31 stainless steel Operation:
Lug Style Butterfly Valve Type 578
Lug Style Butterfly Valve Type 58 General Size: 2 12 Outer Body: Glass-filled PP Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seals: EPDM, FPM, PTFE/FPM Stem: 31 Stainless steel Lugs:
Type 543. Three-way Ball Valve
Three-way Ball Valve Type 543 General Size: ⅜ 2 Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seat: PTFE Seals: EPDM or FPM End Connection: Solvent cement socket, threaded, flanged,
VR DN PVC-U. Check valve
VR DN 10 100 PVC-U Check valve VR DN 10 100 The VR is an angle seat check valve with weighted PVC piston that allows the passage of fluid in one direction only CHECK VALVE Connection system for solvent
CH-VLV TRU-BLOC /TRU UNION BALL VALVES Valves assembled with silicone free lubricant
PVc and Corzan cpvc ball valves, Butterfly Valves, Check Valves, Specialty Valves, accessories and replacement parts CH-VLV-0912 Effective Sept. 17, 2012 Supercedes CH-VLV-0111 dated January 20, 2011 TRU-BLOC
Ball Valves George Fischer Type 353, 354, 355 COLORO Ball Valves. Technical Features
Ball Valves George Fischer Type 5, 54, 55 COLORO Ball Valves The George Fischer Type 5, 54, and 55 plastic ball valves feature: monobloc structure provides high safety level: user cannot dissassemble or
Schedule 80 - CPVC Pressure Fittings
Discount Codes 03 Schedule 80 CPVC Schedule 80 - CPVC Pressure Fittings List Prices Effective: August 25, 2012 Revised September 2014 2 Schedule 80 - CPVC Products Catalog www.lascofittings.com Pricing
DK Series Pneumatic Diaphragm Valves Product Data Sheet
1" through 2-1/2" 1/2" and 3/4" < STANDARDS > ASTM D1784 ASTM D1785 ASTM D4101 ASTM D3222 ASTM D2464 ASTM D2466 ASTM D2467 ASTM F441 ASTM F437 ASTM F439 ASTM F1498 IPEX DK Series are the ideal solution
introduction VM Series Manual Diaphragm Valves Product Data Sheet
Product Data Sheet introduction < STANDARDS > ASTM D4101-86 ASTM D3222 ASTM D2467 ASTM D2466 ASTM D1785 ASTM D1784 ASTM F441 ASTM F439 IPEX VM Series Diaphragm Valves are the ideal solution f modulating
Type 514, 515, 517, 519
Diaphragm Valve Type 514, 5, 517, 519 General : ½ 2 Material: PVC, CPVC, PROGEF Standard PP, PROGEF Natural PPn, ABS, SYGEF Standard PVDF, SYGEF Plus PVDF-HP Diaphragm: EPDM, FPM, NBR, PTFE/EPDM, PTFE/FPM,
SUPERSEDES ABS-C0811/AUG.
ABS-C0612/R JUNE 2012 SUPERSEDES ABS-C0811/AUG. 2011 SANITARY TEE REDUCING TEE TEE - Left Side Inlet 600007 1 1/4" 0 62852 60000 5 50 4,800 15.41 600015 1 1/2" 0 62852 60001 2 90 2,880 8.27 600023 2"
Mechanical Piping.
Mechanical Piping www.anvilintl.com JULY 2016 For the most current product/pricing information on Anvil products, please visit our website at www.anvilintl.com BUILDING CNNECINS HA LAS For over 160 years,
PP-RCT Plumbing and HVAC Piping Systems
PP-RCT Plumbing and HVAC Piping Systems Pipe Fittings Valves 9-2016 Efficient Sustainable Green Technology Asahi/America, in partnership with Bänninger of Germany, introduces - Asahitec PP-RCT piping systems
SDR-26 (160 PSI) SDR-21 (200 PSI) SDR-17 (250 PSI) MINIMUM WALL (IN.) 20 LENGTH. 1.5" 1.900" N/A N/A N/A.090" ".419 lbs..415 lbs.
u ASTM D2241 PRESSURE PIPE Gasketed Pipe Specifications Northern Pipe Products ASTM D2241 IPS Pressure Rated Pipe is manufactured from compounds conforming to cell class 12454 in accordance with ASTM D1784.
+GF+ PNEUMATIC ACTUATED BALL VALVE +GF+ PNEUMATIC ACTUATED BALL VALVE +GF+ PNEUMATIC ACTUATED BALL VALVE 3-16
+GF+ PNEUMATIC ACTUATED BALL VALVE Type 21/2 2-way True Union Pneumatically actuated ball valve for aggressive fluids and industrial applications. Based on the new Type 546 ball valve, the Type 21-2 uses
introduction VKD Series Automated Ball Valves Product Data Sheet < STANDARDS >
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D2464 ASTM D2466 ASTM D2467 ASTM D4101 ASTM F1498 ASTM F437 ASTM F439 IPEX VKD Series Automated Ball Valves offer a variety of advanced features
PRICE EACH PVC DWV FITTINGS SMALL AND LARGE DIAMETER MOLDED FITTINGS MARCH 1, 2017
LIST U19-0317-IP PVC DWV FITTINGS SMALL AND LARGE DIAMETER MOLDED FITTINGS MARCH 1, 2017 SUPERSEDES U19-1116-IP (NOVEMBER 1, 2016) Our website pricing is the current list price and may vary from our printed
PVC Gasketed Fittings for PVC IPS Pressure Pipe ENGINEERED FOR DURABILITY
For the most up-to-date version of this price list, EFFECTIVE MARCH 4, 2019 ENGINEERED FOR DURABILITY HARRINGTON CORPORATION P.O. BOX 10335 LYNCHBURG, VIRGINIA 24506-0335 For the most up-to-date version
TBH Series True Union Ball Valve Product Guide
17 Q U A L I T Y S E R V I C E I N T E G R I T Y F LOW C O N T R O L TBH Series True Union Ball Valve Product Guide OVERVIEW A new generation of thermoplastic floating ball valves. The TBH Series features
611, 671. Diaphragm Valve, Metal
Diaphragm Valve, Metal Construction The 611 and 671 manually operated 2/2-way metal diaphragm valves have a low maintenance plastic bonnet and an integral optical position indicator as standard. Features
VA Air Release Valves Submittal Data Sheet. Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: introduction
Submittal Data Sheet Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Date Date Date introduction < STANDARDS > IPEX VA Air Release Valves are of a unique design,
Item Component Remarks Type 4393 Type ), SA Vulcanized soft seal disc SA L SA L
Available designs materials Materials Item Component Remarks 3 4 1 Base / Inlet body 2 Outlet body Threaded connection Flange connection 2.1 Outlet adaptor Flange connection 2.4 Outlet flange Flange connection
Forged High Pressure Pipe Fittings
Forged High Pressure Pipe Fittings Forged High Pressure Pipe Fittings Pressure Class Socket Weld Forged Fittings Products Dimension Specifications Pressure Class Threaded Forged Fittings Products Dimension
TKD Series 3-Way Automated Ball Valves Product Data Sheet. Body Material: PVC Size Range: 1/2" through 2"
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D2464 ASTM D2466 ASTM D2467 ASTM F1498 IPEX TKD Series 3-Way Automated Ball Valves can be used for flow diverting, mixing, or on/off isolation.
abs section guide application guide standards and approvals
abs Acrylonitrile - Butadiene - Styrene (ABS) is a rigid pressure piping system renowned for its high impact strength and durability which combine to give exceptional toughness. It is suitable for use
+GF+ 546 Double Union Ball Valves
71 PRICE LIST 1 May 2018 Plastic Systems offers the broadest range of high quality thermoplastic valves available from stock in New Zealand. These valves are ideally suited for chemical handling and other
:,Rhino SD/XD G/D 24 Vdc ISO
:,Rhino SD/XDG/D Vdc ISO ()Rhino SD/XD() SD/XD Rhino SD/XDG/D Vdc ISO Rhino SD/XD, Rhino SD/Xd, (Rhino SD/XD) 006 Nordson Corporation P/N 75606A-0 Rhino SD/XDG/D Vdc ISO 0 9 5 8 7 6 P/N 75606A-0 006 Nordson
Spears Low-Extractable SCHEDULE 80 PIPE
Spears Low-Extractable SCHEDULE 80 PIPE NOMINAL PIPE MAX. W.P. LGTHS/ PART NUMBER AVG. OD AVG. ID MIN. WALL LBS/FT SIZE PSI* CARTONS 1/2" LXT-005.840.528.147 420.202 22 3/4" LXT-007 1.050.724.154 340.273
Filters & Strainers Technical Information TECHNICAL INFORMATION WEIGHTS & DIMENSIONS
Filters & Strainers Technical Information TECHNICAL INFORMATION WEIGHTS & DIMENSIONS Contact Spears for any Information not found. Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for
Ultra Proline. ECTFE (Halar ) Single Wall Piping System
ECTFE ( ) Single Wall Piping System 222 - Specification Natural Ethylene Chlorotrifluoroethylene (ECTFE) Chemical Piping System REV:IN0512HA Materials: ASTM D3275 Class 2 resin. Raw resins are certified
R677. Diaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction All medium wetted parts, the bonnet and handwheel of the GEMÜ 2/2-way diaphragm valve are made of plastic. The low maintenance plastic bonnet has an ergonomically
Section 7. Socket Weld and Threaded Fittings. Socket Weld and Threaded Fittings 7-1
Section 7 Socket Weld and Threaded Fittings This Section contains dimension and tolerance information extracted from American and British specifications applicable to socket weld and threaded fittings.
Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
611, 671. Diaphragm Valve, Metal
Distributed by: Tel: 905.677.9000 Toll Free: 1.0.486.7863 www.tricanada.com Diaphragm Valve, Metal Construction The 611 and 671 manually operated 2/2-way metal diaphragm valves have a low maintenance plastic
introduction RV Series Sediment Strainers Product Data Sheet
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D4101-86 ASTM D2466 ASTM D2467 ASTM F439 ASTM D2464 ASTM F1498 ASTM F437 IPEX RV Sediment Strainers protect critical pipeline components by
Stop valves SVA-S and SVA-L
MAKING MERN LIVING POSSIBLE echnical brochure Stop valves SVA-S and SVA-L SVA Stop Valves are available in angleway and straightway versions and with Standard neck (SVA-S) and Long neck (SVA-L) he stop
Type 145. Electrically Actuated Wafer Butterfly Valve
Electrically Actuated Wafer Butterfly Valve Type 1 General Size: 2 12 Outer Body: Glass-filled PP Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seals: EPDM, FPM, PTFE/FPM Stem: 316
Distributed By Aetna Plastics Pneumatically Actuated Diaphragm Valve DIASTAR Ten and TenPlus General Size: ½ 2 Material: PVC, CP
Pneumatically Actuated Diaphragm Valve DIASTAR Ten and TenPlus General : ½ 2 Material: PVC, CPVC, PROGEF Standard PP, PROGEF Natural PPn, ABS, SYGEF Standard PVDF, SYGEF Plus PVDF-HP Diaphragm: EPDM, FPM,
CPVC CTS Fittings, Valves & Pipe COPPER-TUBE-SIZE
CPVC CTS Fittings, Valves & Pipe COPPER-TUBE-SIZE Visit our web site: www.spearsmfg.com PRICE SCHEDULE CTS-1-1009 Effective October 26, 2009 Supersedes CTS-1-0308A TEE Socket x Socket x Socket 4101-005
DK-LOK Hydraulic Pipe Fittings
Class 2000, 3000, 6000, 9000 fittings Catalog No. C-2 June 2012 DK-LOK Hydraulic Pipe Fittings are designed and manufactured to the following standards. ASME B 16.11-2005: Forged fittings, Socket-welding
introduction < STANDARDS >
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D2464 ASTM F437 ASTM F1498 IPEX VA Air Release Valves are of a unique design, controlled by media and not pressure. Intended for use with tanks,
TRU-BLOC TRUE UNION BALL VALVES - PVC
AND CORZAN BALL VALVES, BUTTERFLY VALVES, CHECK VALVES, SPECIALTY VALVES, ACCESSORIES AND REPLACEMENT PARTS CH-VLV-1018 Effective October 1, 2018 Supercedes CH-VLV-0118 dated January 1, 2018 Visit our
BYV Series Butterfly Valve Product Guide FLOW CONTROL
BYV Series Butterfly Valve Product Guide FLOW CONTROL 17 Q U A L I T Y S E R V I C E I N T E G R I T Y 1 OVERVIEW Engineered Hand Lever Design for Enhanced Strength and UV Performance Ergonomic Grip and
Type 561/562 Cone Check Valve
Type 561/562 Cone Check Valve Standard Features Size 3/8 4 Material Body: PVC, CPVC, PROGEF Standard, Polypropylene, SYGEF PVDF, ABS Spring (562 only): Stainless Steel Optional: Nimonic C/Hastelloy C,
Flowmeter DFM
Flowmeter DFM 165 50 Nominal size DN 10-65 Nominal size /8 2 1/2 Nominal pressure PN 10 bar Features Measuring range to 50,000 l/h suitable for a wide range of applications for gaseous medium types, water,
introduction FK Series Butterfly Valves Product Data Sheet
Product Data Sheet introduction < STANDARDS > ASTM D4101-86 ASTM D1784 ASTM D3222 IPEX FK Series Butterfly Valves offer superior strength and chemical resistance in highly corrosive environments and process
Schedule 80 PVC Industrial Products & Accessories True Union 2000 Industrial Ball Valves
True Union 000 Industrial Ball Valves Pressure Rating @ 7 F ( C), Water /" - " 5 psi " - 8" 50 psi All Flanged 50 psi Socket Style SR Threaded Style " Lever Handle Style PVC = 0 F (0 C) Rated for Vacuum
Stop valves SVA-S and SVA-L
MAKING MODERN LIVING POSSIBLE echnical brochure Stop valves SVA-S and SVA-L SVA Stop Valves are available in angleway and straightway versions and with Standard neck (SVA-S) and Long neck (SVA-L) he stop
VXE Series Ball Valves Product Data Sheet
< STANDARDS > ASTM D1784 ASTM D2466 ASTM D2467 ASTM F439 ASTM D2464 ASTM F437 ASTM D1498 The IPEX EasyFit VXE Series True Union Ball Valves represent the latest innovation in thermoplastic ball valve manufacturing
EverTUFF CPVC CTS Fittings, Valves, Pipe & Cement
CTS CPVC uct EverTUFF CPVC CTS Fittings, Valves, Pipe & Cement EverTUFF CPVC CTS Fittings, Valves, Pipe & Cement PRODUCT Contact Spears for any Information not found. Page 1 Spears Manufacturing Company
CPVC HOT & COLD PLUMBING SYSTEM PRICE LIST
CPVC HOT & COLD PLUMBING SYSTEM PRICE LIST With effect from 1st June, 2015 SDR-11 (3 Mtr. Length) (Rate per mtr.) 15 ½ M011110301 100 75.00 20 ¾ M011110302 50 110.00 25 1 M011110303 30 174.00 32 1¼ M011110304
Ball & Socket Fittings (Bauer Style)
Page 96 Ball & Socket Fittings (Bauer Style) Elbow-Bauer Style 3-1/ * *1 MM 76 89 108 133 159 194 2 300 * Locking Bar (part # 9-7318) for & 1 Lever is Sold Separately 6-9038 6-9039 6-9040 6-9041 6-9042
Type 437. Type 437. Available designs. Cap H2 Adjusting screw with bushing. Axial needle 69 beering. Lock nut. Spring plate. Spring plate. Pin.
Available designs 40 18 Cap H2 Adjusting screw with bushing 19 Lock nut Axial needle 69 beering 16 Spring plate 12 Spindle 54 Spring 2 Outlet body 17 Spring plate 57 Pin 61 Ball 7 Disc 1 Body Threaded
ABS Pipe metric system Plain PN10
S Pipe metric system Plain PN10 t (mean) Da (min) Size Thickness Weight Length ode t Da mm kg/m m 16 1.5 0.07 3 11 565 305 20 1.6 0.10 3 11 565 306 25 1.9 0.14 3 11 565 307 35 2.1 0.21 3 11 565 308 16
Table Of Contents. Assembly Instructions. Identification of Sync-Lok Tube Fittings. Reducing Port Connector 36. Male Elbow 11
able Of Contents eneral Information 1 Union Cross 27 Ordering Information 3 Reducer 28 ube Selection Data 5 Bulkhead Reducer 29 Male Connector 7 Male Adapter 31 Male Bore hrough Connector 9 emale Adapter
introduction < STANDARDS >
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D2466 ASTM D2467 ASTM F439 ASTM D2464 ASTM F437 ASTM F1498 IPEX EasyFit SXE Ball Check Valves represent the latest innovation in thermoplastic
Innovation, Versatility & High Performance Technology
Butterfly s Overview Innovation, Versatility & High Performance Technology Spears innovative design departs from traditional liner-seat type valves to eliminate seat creep, reduce operating torque and
manual valves inch sizes
Spears True Union 2000 Industrial Vented Ball Valve Description: In-line double union ball valve Maximum Fluid Pressure at 20 C: All sizes 1 /2 to 2-16 bar; sizes 2 1 /2 to 4-10 bar; all sizes flanged
HVAC Products 2016 EDITION NCI CANADA INC.
HVAC Products 2016 EDITION NCI CANADA INC. YOUR SINGLE SOURCE SOLUTION NCI Canada Inc. is a Canadian National master distributor of high quality valves, fittings, pipes and related products serving residential,
introduction FE Series Butterfly Valves Product Data Sheet
Product Data Sheet introduction < STANDARDS > ASTM D1784 IPEX FE Series Butterfly Valves incorporate many features of our industrial FK valve, yet the all PVC construction and EPDM liner make this valve
Material Specification PVC valves shall meet ASTM D1784 cell classification 124 standards. CPVC valves shall meet ASTM D1784 cell classification 23447
Electrically Actuated Lug Butterfly Valve Type 147 General Size: 2 12 Outer Body: Glass-filled PP Material: PVC, CPVC, PROGEF Standard PP, ABS, SYGEF Standard PVDF Seals: EPDM, FPM, PTFE/FPM Stem: 316
pvc-c manual valves inch sizes manual valves inch sizes Spears True Union 2000 Industrial Ball Valve
pvc-c Spears True Union 2000 Industrial Ball Valve Description: In-line double union ball valve with lockable handle Maximum Fluid Pressure at 20 C: Sizes 1 /2 to 2-16 bar; sizes 2 1 /2 to 6-10 bar All
SWING JOINT & HEAVY TURF
PRICE GROUP DESCRIPTION 11 SWING JOINT 08 HEAVY TURF DISCOUNT MULTIPLIER PRODUCTS SWING JOINT & HEAVY TURF IRRIGATION FITTINGS INCLUDES: PVC SWING JOINTS AND IRRIGATION ACCESSORIES LSJHT EFFECTIVE JULY
Yl)HAl STrrl (INDIA) Forged High Pressure Pipe Fittings. All ISO 9001:2003/ ISO 14001:2004 / 8S Ol!SAS 18001:2007 / PED Al'PROl'ED 97/23/EC
Forged High Pressure Pipe Fittings Forged High Pressure Pipe Fittings Summary : Summary : Type 1. Elbow, Tee, Cross, Couplin g, Half Coupling, Cap, Plug, Bushing, Union, HEX. Nipple, Swage 2. nipple, Bull
Type 459. Type 459. Available designs. Cap H2. with bushing 19. Lock nut. Bonnet. Outlet flange 2.4 Outlet adaptor 2.1. spacer.
Available designs 40 Cap H2 18 Adjusting screw with bushing 19 Lock nut 9 Bonnet 16 Spring plate 54 Spring 12 Spindle 17 Spring plate 14 Split ring 60 Gasket 8 Guide 57 Pin 61 Ball 7 Disc 2 Outlet body
FK DN PVC-U Butterfly valve
.co.th FK DN 40 300 PVC-U Butterfly valve FK DN 40 300 The FK is a butterfly valve for shutting off or regulating flow, with structural characteristics that make it ideal for industrial applications requiring
FK Series Butterfly Valves Product Data Sheet
< STANDARDS > ASTM D4101-86 ASTM D1784 ASTM D3222 IPEX FK Series Butterfly Valves offer superior strength and chemical resistance in highly corrosive environments and process flow conditions. The special
pvc-u section guide application guide standards and approvals
pvc-u Unplasticised Polyvinyl Chloride (PVC-U) is the most widely used of all plastics used for pipe installations. It is rigid, versatile, and is suitable for both above or below ground installations.
ABS DWV FITTINGS APRIL 1, 2013
LIST C10-11-111 ABS DWV FITTINGS APRIL 1, 2013 SUPERSEDES C10-11-110 (JUNE 1, 2012) Our website pricing is the current list price and may vary from our printed price list. Please visit our website for
Pressure Pipes & Fittings
Pressure Pipes & Fittings Description: UPVC and CPVC pipes for hot and cold water supply under pressure. Range: Metric series fromø16 up toø315 mm, Imperial series fromø1/2" up toø1". Pressure Rating: