Reproduction. Not for. 17.5, 18, 22 & 26 HP 96cm & 107cm Rear Discharge European Tractor RD Series. Parts Manual for

Transcription

1 Parts Manual for Rear Discharge European Tractor RD Series Model No. Description ERPX17538RDF ERPX1838RDF ERTX2242RDF ERTX2642RDF Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough, GA, U.S.A Revision: A 1/25/2013

2 Table Of Contents PAGE GROUP 4 Wheel & Tire Group 6 Hood, Grille & Dash Group 8 Seat Deck & Fuel Tank Group 10 Steering Group 12 Frame & Front Axle Group 16 Controls Group 18 Engine Group HP, 18HP, 22HP & 26HP 20 Transmission Group - Hydro Gear Transmission SERVICE PARTS - Hydro Gear Lift Group 30 96cm Mower Deck - Housing, Arbors & Blade 32 96cm Mower Deck - Clutch Group 34 96cm Mower Deck - Support Group cm Mower Deck 40 Guard Group 42 Collector Group Liter 46 Collector Group Liter 50 Decal Group 52 Electrical Group RD Series 3 TP A-TC-N

3 Wheel & Tire Group 4 RD Series

4 Wheel & Tire Group Item Part No Qty Description SM 2 WHEEL& TIRE ASSEMBLY, Front (Includes Ref. Nos , , , & ) SM 1 FITTING, Lube SM 2 BEARING, 3/ SM 4 VALVE STEM & CAP SM 1 WHEEL & BUSHINGS ASSEMBLY, Front (Includes Ref. Nos & ) SM 1 TIRE, Kenda, Turf Rider, Front, 15 x SM 2 TUBE, Tire, Front YP 2 WHEEL & TIRE ASSEMBLY, Rear, 20 X 8-8 (Use on 17.5HP & 18HP Models) (Includes Ref. Nos & ) WHEEL & TIRE ASSEMBLY, Rear, 22 x 10-8 (Use on 22HP & 26HP Models) (Includes Ref. Nos & ) TIRE, Rear, K358 x 20 x (Not a serviceable part, order Ref. 0060) TIRE, Rear, K358 x 22 x 10-8 (Not a serviceable part, order Ref. 0060) SM 2 TUBE, Tire, Rear MA 4 HUB CAP X3MA 4 E-RING X195MA 4 WASHER, Flat X160MA 6 WASHER, Flat, 3/4 x 1-1/ SM 2 SPACER, 3/4 ID x 1-1/4 OD x 1-5/8, RH (Use on R.H. Side Only) MA 2 KEY, Square, 3/ YP 1 SPACER, Wheel, LH (Use on L.H. Side Only) Footnotes: RD Series 5

5 Hood, Grille & Dash Group 6 RD Series

6 Hood, Grille & Dash Group Item Part No Qty Description DYP 1 HOOD, One Piece (Use on 17.5HP & 18HP Models) DYP 1 HOOD, One Piece, Vent Holes (Use on 22HP & 26HP Models) YP 1 AIR DUCT YP 1 GRILLE, Front AYP 1 HINGE, Hood, LH AYP 1 HINGE, Hood, RH YP 2 BOLT, Carriage, 5/16 x 1, G YP 2 SCREW, 7mm x 16mm YP 1 DASH YP 1 KNOB, Parking Brake YP 1 KNOB, Cruise SM 2 SCREW, Hex Washer Head Taptite, 5/16-18 x 3/ SM 2 WASHER, 5/16 x YP 1 COVER, Steering Shaft YP 1 HEADLIGHT, Led, LH (Use on 17.5HP & 18HP Models) YP 1 HEADLIGHT, Led, LH (Use on 22HP & 26HP Models) YP 2 SCREW, Pan Head Phillips, #10-24 x 7/ YP 1 ROD, Dash Support, 1/4 Dia. x 10" SM 2 NUT, Ny-Lock YP 1 HEADLIGHT, Led, RH (Use on 17.5HP & 18HP Models) YP 1 HEADLIGHT, Led, RH BMYP 1 BUMPER, Front YP 1 TRIM, Hood SM 2 NUT, Hex Flange, 5/16-18, ESNA YP 4 SCREW, PT GS 4 PALNUT, 3/ SM 2 WASHER, 1/4 x 27/32 OD YP 1 TRIM, Protective YP 8 SCREW, 7mm x 16mm Footnotes: RD Series 7

7 Seat Deck & Fuel Tank Group 8 RD Series

8 Seat Deck & Fuel Tank Group Item Part No Qty Description DYP 1 SEAT DECK, Red BOLT, Carriage, 5/16-18 x 3/4, G SM 4 NUT, 5/16-18, G5 (Use on 22HP & 26HP Models) SM 2 WASHER, Spring, 5/ SM 1 PAD, Footrest, RH SM 1 PAD, Footrest, LH YP 1 FUEL TANK ASSEMBLY MA 2 CLAMP, Hose FUEL TANK, 6L SM 1 HOSE, Fuel, 15.0" CAP, Fuel YP 1 POD, LH YP 1 SEAT, 11" YP 1 SEAT, Bottom, Mesh (Use on 22HP & 26HP Models) YP 1 SEAT, Back, Mesh (Use on 22HP & 26HP Models) AYP 2 SUPPORT, Mesh Seat (Use on 22HP & 26HP Models) SCREW, 5/16-18 x 3/4 (Use on 22HP & 26HP Models) YP 1 SWITCH, Seat (Use on 22HP & 26HP Models) SM 4 SPACER, 5/16 ID x 1-1/4 OD x 5/16" BMYP 1 SUPPORT, Seat BMYP 1 LATCH, Seat SM 4 SCREW, Hex Flange, Whiz Lock, 5/16-1-1/ WASHER, 5/ YP 2 BUMPER, Rubber (Use on 22HP & 26HP Models) AYP 1 PIVOT, Seat SM 2 SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/ YP 1 POD, RH SM 6 SCREW, Hex Washer Head, Plastite, 1/4 x 1/ SM 1 GRIP SM 2 BOLT, Shoulder, 5/16-18 x NUT, Flange Nylock, 5/16-18 (Use on 17.5HP & 18HP Models) YP 2 WASHER, Rubber YP 1 ROD, Fuel Tank MA 1 RING, Foam MA 2 BUMPER, Front SM 2 COVER, Spring (Use on 17.5HP & 18HP Models) SM 2 WASHER, Spring, 5/16 (Use on 17.5HP & 18HP Models) SM 2 BOLT, Carriage, 5/16-18 x 3/4, G5 (Use on 17.5HP & 18HP Models) SM 1 CAPSCREW, Hex Head, 1/2-13 x 1, G SM 1 WASHER, 1/ SM 1 NUT, Hex, 1/ SM 2 SPRING, Compression (Use on 17.5HP & 18HP Models) Footnotes: RD Series 9

9 Steering Group 10 RD Series

10 Steering Group Item Part No Qty Description SM 1 SHAFT, Steering Gear & Spline SM 2 WASHER, 3/4 x SM 2 BUSHING, Steering SM 1 STEERING WHEEL (Use on 17.5HP & 18HP Models) YP 1 STEERING WHEEL (Use on 22HP & 26HP Models) SM 1 NUT, Hex Lock, ESNA Light, 5/8-18, Thin SM 1 RING, Klipring Extension SM 4 SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/ BMYP 1 TOWER BMYP 1 BRACKET, Tank SM 5 CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/ SM 1 WASHER, 5/8 x 1-1/ SM 1 CAP, Steering Wheel, Plain Footnotes: RD Series 11

11 Frame & Front Axle Group 12 RD Series

12 Frame & Front Axle Group Item Part No Qty Description SM 2 CAP, Hub SM 2 E-RING, 3/ SM 4 WASHER, Flat, 3/ SM 1 AXLE, Front SM 2 BUSHING SM 2 SCREW, Hex Flange, Whiz Lock, 7/16-14 x 1-1/ SM 1 PLATE, Axle Support SM 1 NUT, Hex Flange Two-Way Lock, 5/ SM 28 NUT, Hex Flange, Whiz Lock, 5/ SM 2 CAPSCREW, Hex Head, 3/8-16 x 1-1/4,.141 Thread G YP 1 TIE ROD ASM 1 SPINDLE & CUP ASSEMBLY, R.H SM 2 NUT, Hex, Flange, Locking, 3/ YP 1 SPINDLE & ARM ASSEMBLY, L.H BMYP 1 FRAME SM 1 SUPPORT, Front Footrest R.H SM 8 SCREW, Taptite, 5/16-18 x 5/ MA 6 CAPSCREW, Hex Head, Flange Whiz Lock, 5/16-18 x 3/ AYP 1 SUPPORT, Front Footrest L.H SM 1 WASHER, Flat, 5/ SM 1 CAPSCREW, Hex Head, 5/8-11 x 3-1/4 G YP 1 LINK, Drag YP 1 PEDAL ASSEMBLY, Brake YP 1 LATCH, Brake Lock SM 1 BOLT, Shoulder, 5/16-18 x 1-1/ YP 1 WASHER SM 1 SPACER, Pivot AYP 1 PEDAL ASSEMBLY, Forward SM 1 PEDAL, Reverse SM 2 BOLT, Carriage, 5/16-18 x 1-1/ SM 1 SPACER, Foot Pedal BMYP 1 ACTUATOR, RMO Switch AYP 1 BRACKET, Pedal Pivot ASM 1 PLATE, Bearing AYP 1 LIFT SHAFT ASSEMBLY SM 1 BRACKET, Sector Support YP 1 GEAR, Steering WASHER, 5/ SM 2 SPACER, Sector Gear SM 2 SCREW, Hex Head, 3/8-16 x 1-1/4, G SM 2 NUT, Hex Flange, Two Way Lock, 3/ AYP 1 BRACKET, Rear Frame, RH AYP 1 BRACKET, Rear Frame, LH AYP 1 BRACE, Middle Cross Footnotes: RD Series 13

13 Frame & Front Axle Group 14 RD Series

14 Frame & Front Axle Group Item Part No Qty Description BOLT, Carriage, Short Neck, 5/16-18 x 3/4, G CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ AYP 1 BRACKET, Transaxle, RH AYP 1 BRACKET, Transaxle, LH AYP 1 SUPPORT, Deck, R.H AYP 1 SUPPORT, Deck, L.H X84MA 9 CAPSCREW, Hex Head, 5/16-18 x 1, G AYP 1 BRACKET, Middle Back Plate AYP 2 SUPPORT, Upper, Back Plate AYP 2 SUPPORT, Lower, Back Plate AYP 1 BRACE, Cross Deck Support YP 1 BRACKET, Torque AYP 1 BRACKET, Idler Mount ASM 1 CLEVIS, Lift SM 1 SPACER, Pivot SM 1 WASHER, 5/ SM 2 WASHER, 5/ SM 2 WASHER, 5/ SM 2 CAPSCREW, Hex Head, 5/16-18 x 1-1/4, G WASHER, 5/ BMYP 1 BRACKET, Tower Support, LH BMYP 1 BRACKET, Tower Support, RH YP 1 UPSTOP SM 2 NUT, Hex Flange, Two Way Lock, 5/ ASM 1 HOOK, Mower, Hitch SM 2 BUSHING, 3/8 ID x 5/8 OD x 1/2" AYP 2 UPSTOP Footnotes: RD Series 15

15 Controls Group 16 RD Series

16 Controls Group Item Part No Qty Description SM 1 ROD, Cruise Latch, 2.83" SM 1 LATCH, Cruise SM 1 SPRING, Extension 7-3/ SM 1 BOLT, Shoulder, 5/16-18 x 1-5/ X79MA 3 NUT, Flange, 5/16-18, G SM 1 PEDAL, Brake Rubber NUT, Hex Flange, ESNA, 3/ AYP 1 BRACKET, Idler Front Movable YP 1 PULLEY, 3 OD Plastic BOLT, Carriage, 3/8-16 x 1-1/ SM 1 PAD, Foot Pedal, Forward SM 1 PAD, Foot Pedal, Reverse SM 1 ROD, Parking Brake YP 1 ROD, Cruise Latch YP 1 BELT, Primary, M/D (47.89" EL, HA Section) YP 1 IDLER, Backside SM 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4, G YP 2 BELT GUIDE YP 1 SPRING, Extension YP 1 PULLEY, Secondary Stack YP 1 BOLT, Carriage, 3/8-16 x SM 1 SPRING, Extension 7-1/2" YP 1 ROD, Clutch YP 1 PIN, Cotter ZMA 1 NUT, Adjusting MA 2 WASHER, Flat, 3/ BMYP 1 BRACKET, Stack Pulley, Left SCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ YP 2 SPACER SM 1 NUT, Push Pal, 3/ SM 1 SPRING, Extension BMYP 1 BRACKET, Stack Pulley, Right PIN, Cotter X84MA 1 NUT, Hex Flange, Centerlock, 3/8-16 Footnotes: RD Series 17

17 Engine Group HP, 18HP, 22HP & 26HP 18 RD Series

18 Engine Group HP, 18HP, 22HP & 26HP Item Part No Qty Description G B1 1 * ENGINE, 17.5HP Briggs & Stratton, Model 31G B B1 1 * ENGINE, 18HP Briggs & Stratton, Model B B1 1 * ENGINE, 22HP Briggs & Stratton, Model B B1 1 * ENGINE, 26HP Briggs & Stratton, Model B YP 1 VALVE, Shut Off Oil Drain BMYP 1 HEAT SHIELD SM 10 SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/ ASM 1 SUPPORT, Muffler SM 2 SCREW, Hex Washer Head, Taptite, 1/4-20 x 1/2 (Qty 4 used on 18HP Models) SM 1 WIRE CLIP YP 1 THROTTLE CONTROL, Choke-A-Matic (Single) YP 1 THROTTLE CONTROL, Choke-A-Matic (Twin) SM 4 SCREW, Hex Washer, Taptit, 3/8-16 x SM 1 LOCKWASHER, External Tooth SM 1 PULLEY & HUB ASSEMBLY, Engine SM 2 TIE, Self Locking AYP 1 BRACKET, Electric Clutch Torque SM 2 CAPSCREW, Hex Head, 5/16-18 x 3/4, G SM 2 NUT, Hex Flange, Whiz Lock, 5/ YP 1 SPACER, Electric Clutch YP 1 CLUTCH, Electric, GT1A-EH SM 1 WASHER, 7/ SM 1 LOCKWASHER, Spring YP 1 CAPSCREW, Hex Head, 7/16-20 x SM 1 GASKET, Exhaust (Qty 2 used on Twin) ** SCREW, Hex SEMS Lock Washer 5/16-18 x 7/8 (Qty 4 used on Twin) SM 2 NUT, Hex Flange, Whiz Lock, 5/ SM 2 PIVOT, Hood SM 2 BOLT, Carriage, 5/16-18 x AYP 1 BRACKET, Muffler SM 1 EXHAUST PIPE, Single ASM 1 HEAT SHIELD, Single ASM 1 HEAT SHIELD, Twin YP 1 MUFFLER, Single (Used on 17.5HP Models) SM 1 MUFFLER, Twin (Used on 18HP Models) YP 1 MUFFLER, Twin (Use on 22HP & 26HP) BMYP 1 GUARD, Pulley YP 1 SPACER, Electric Clutch YP 1 HARNESS, Ogura SM 1 EXHAUST PIPE, RH (Twin) SM 1 EXHAUST PIPE, LH (Twin) Footnotes: Note* To verify your specific engine model, please reference the ID Tag located on your engine. See your local Briggs & Stratton distributor for parts and service. Note: ** Purchase engine parts from engine manufacture dealer. RD Series 19

19 Transmission Group - Hydro Gear RD Series

20 Transmission Group - Hydro Gear Item Part No Qty Description YP 1 * TRANSMISSION, Hydro Gear, SM 8 SCREW, Hex Head Flange Lock, 5/16-18 x 2-3/4, G SM 8 NUT, Hex Flange, Whiz Lock, 5/ YP 1 LEVER, Roll Release SM 5 PIN, Quick YP 1 BELT, Secondary (81.37" EL, HA section) X75MA 1 SPRING, Extension BMYP 1 BRACKET, Roll Release YP 3 PULLEY, Idler SM 3 BOLT, Carriage, Short Neck, 3/8-16 x 1-1/2, G X84MA 3 NUT, Hex Flange, Centerlock, 3/ YP 1 SPEED CONTROL, Short Link AYP 1 SPEED CONTROL ASSEMBLY X91MA 2 WASHER, Flat, 13/ SM 1 PIN, Cotter ZMA 1 NUT, Adjusting X53MA 1 WASHER, Flat, AYP 1 LINK, Speed Control AYP 1 BRACKET, Idler, Rear SM 1 SPACER, Pivot SM 1 BOLT, Carriage, Short Neck, 5/16-18 x 1, G SM 2 NUT, Hex Flange, Whiz Lock, 5/ YP 1 BELT GUIDE SM 1 SPRING, Extension BMYP 1 PLATE, Front Fixed Idler CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ X92MA 1 SPRING, Extension Footnotes: Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at (U.S Int'l 32 (0) ) RD Series 21

21 Transmission SERVICE PARTS - Hydro Gear RD Series

22 Transmission SERVICE PARTS - Hydro Gear Item Part No Qty Description * MAIN HOUSING ASSEMBLY * SIDE HOUSING ASSEMBLY * CENTERSECTION ASSEMBLY * TRUNNION, Swashplate * BLOCK ASSEMBLY * SEALANT, 10.1 oz. (Not Illustrated) * SCREW, Hex Washer, 1/4-20 x 1-1/ SHAFT, Input RING, Retaining WASHER, Flat, 1.23 x 1.57 x RING, RETAINING SEAL, LIP 17 x 40 x BEARING, BALL 17 x 40 x * SCREW, Hex Flange, With Patch, 5/16-24 x 15/ * SEAL, Lip, 18 x 32 x 7 (Not a servicable part, order kit # 1270) * ARM, Control * BEARING, Thrust, 30 x 52 x * SHAFT, Motor * GEAR, Pinion, 12T * GEAR, 10T/49T * GEAR, Jackshaft, 10T * BUSHING, Sleeve (Inboard) * BUSHING, Sleeve, 3/4 x x 5/ * WASHER, Flat, 3/4 x 1-1/2 x 7/ * SEAL, Lip, 3/4 x x 1/4 (Not a servicable part, order kit # 1270) * SHAFT, Axle, 3/4 x (Key, RH) * SHAFT, AXLE, 3/4 x (Key, LH) * KIT, Miter Gear * RING, Retaining Spiral * PIN, Jackshaft, 1/2 x * MAGNET, Ring SCREW, Hex Flange, 3/8-24 x 2-1/ * ROD, Actuator Bypass * ARM, Bypass * RING, Retaining, External, 1/ * SEAL, Lip, 1/4 x 3/4 x 1/4 TC (Not a servicable part, order kit # 1270) * WASHER, Flat, 5/8 x 1 x 1/ * RING, Retaining * BUSHING, Center Block * SPRING, Block * WASHER, Thrust,.59 x.79 x * BRAKE YOKE KIT * DISK, Brake * PUCK, Brake Footnotes: Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at (U.S Int'l 32 (0) ) RD Series 23

23 Transmission SERVICE PARTS - Hydro Gear RD Series

24 Transmission SERVICE PARTS - Hydro Gear Item Part No Qty Description * PLATE, Puck * PIN, Brake Actuating * SCREW, Hex Head, With Patch, 1/4-20 x SPACER,.26 x.57 x * SPRING, Brake arm Bias SCREW, Square Head, Ribbed, 5/ * ARM, Brake * NUT, Castle, 5/ * PIN, Cotter, 3/32 x 3/ * SPRING, Compression Brake, Anti-Drag * WASHER, Flat,.51 x 1.0 x * WASHER, Flat,.34 x.88 x * KIT, Seal * FITTING, 5/16 SAE 5/32 TUBE * HOSE, Expansion Tank, 7.56 In SPRING CLIP, Housing Thrust (3/4" Axle) * BEARING, Ball,.62 x 1.38 x * CAPSCREW, Socket Head, 5/16-24 x 1-1/ * SPACER, Locating * SCREW, Countersunk, 5/16-18 x * ARM, Return * PUCK, Adjusting * WASHER, Flat,.32 x 1.60 x * SPRING, Extension, Double Loop * SPACER,.26 x.56 x * BRACKET, Torque * WASHER, Flat,.71 x 1.16 x * PLUG, 9/16-18 (METAL) * SCREW, Torx Head, 5/16-18 x 1-1/ * O-RING,.299 x.505 x. 103 (Not a servicable part, order kit # 1270) * SPRING, Guide * PIN, Spring,.304 x * CENTERSECTION ASSEMBLY, Filter, Bypass (Not Illustrated) (Includes Ref. Nos. 0030, & 1250) * CENTERSECTION (5-Piston) (Not a serviceable part, order kit #1240) * FILTER ASSEMBLY (Includes Ref. Nos , , , & ) * BASE, Filter, With Poppet (Not a serviceable part, order kit #1250) * SPRING, Bypass, 1/2" (Not a serviceable part, order kit #1250) * ACTUATOR, Bypass (Not a serviceable part, order kit #1250) * DEFLECTOR (Not a serviceable part, order kit #1250) * BOTTOM, Filter (Not a serviceable part, order kit #1250) FAN & PULLEY KIT (Includes Ref. Nos , , , & ) * FAN, 7" (10 BLADE) (Not a serviceable part, order kit #1260) * PULLEY, Cupped, 4-1/2" (Not a serviceable part, order kit #1260) Footnotes: Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at (U.S Int'l 32 (0) ) RD Series 25

25 Transmission SERVICE PARTS - Hydro Gear RD Series

26 Transmission SERVICE PARTS - Hydro Gear Item Part No Qty Description * NUT, Hex Jam, With Patch, 1/2-20 (Not a serviceable part, order kit #1260) * WASHER, Slotted,.53 x 1.63 x.06 (Not a serviceable part, order kit #1260) * HUB, Pulley (Not a serviceable part, order kit #1260) SEAL & O-RING KIT (Includes Ref. Nos. 0170, 0340, 0510 & 1110) EXPANSION TANK KIT (Includes Ref. Nos , , & ) * TANK, Expansion (Not a serviceable part, order kit #1280) * CAP, Expansion Tank (Not a serviceable part, order kit #1280) * BOLT, Self Tapping, x 1/2 (Not a serviceable part, order kit #1280) * BRACKET, Expansion Tank (Not a serviceable part, order kit #1280) * KIT, 60T Bull Gear Diff Pins (Includes Ref. Nos & ) * GEAR, 60T * PIN, 1/2 Footnotes: Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at (U.S Int'l 32 (0) ) RD Series 27

27 Lift Group 28 RD Series

28 Lift Group Item Part No Qty Description ROD, Lift Handle, 17.7" SPRING, Torsion, 2.12 Inch NUT, Hex, Flange Whizlock, 5/ BM 1 ARM, Rear Lift, RH BOLT, Shoulder ROD, Lower Life, LG TRUNNION NUT, Hex Flange, 3/8-16 ESNA NUT, Hex, Flange Lock, 3/ CLIP, Spring A 1 QUADRANT, Lift Height DECAL, Height Of Cut BOLT, Carriage, 1/4-20 x 5/8 G NUT, Hex Flange Whiz, 1/ WASHER, 1/ PIN, Threaded Shoulder SPACER ROD, Lift, 5.43 LG BM 1 ARM, Rear Lift, LH WASHER, Rubber WASHER, Flat, SPRING, Extension Footnotes: RD Series 29

29 96cm Mower Deck - Housing, Arbors & Blade 30 RD Series

30 96cm Mower Deck - Housing, Arbors & Blade Item Part No Qty Description HOUSING, Spindle BEARING, Ball, 20mm SHAFT, Spindle, LH SHIELD, Arbor SPACER, Bearing RING, Self Locking SHAFT, Spindle, RH (LH Thread) SHIELD, Arbor SPACER, Bearing BEARING, Ball, 20mm HOUSING, Spindle RING, Self Locking CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 1-1/ SPACER, Mower Drive PULLEY, Deep Groove WASHER, Spring, 0.475ID x 1-3/4 OD CAPSCREW, Hex Head, 7/16-14 x 2-3/4. G CAPSCREW, Socket Head, 7/16-14 x 2-3/4, LH BM 1 BLADE, RH, 19.5" CAPSCREW, Socket Head, 7/16-14 x 1, LH BM 1 BLADE, LH, 19.5" CAPSCREW, Hex Head, 7/16-14 x 1, G ADAPTER, Washout Port CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ NUT, Hex Flange, Whiz Lock, 5/ WASHER, 5/ DECK, CENTER CAP BOLT, Carriage, Short Neck, 5/16-18 x 3/4, G NUT, Hex Flange, Whiz Lock, 5/ FITTING, Grease BM 1 DECK ASSEMBLY Footnotes: RD Series 31

31 96cm Mower Deck - Clutch Group 32 RD Series

32 96cm Mower Deck - Clutch Group Item Part No Qty Description BM 1 BRACKET, Idler, RH BM 1 SUPPORT, Idler Arm CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ BM 1 DECK IDLER ASSEMBLY SPACER, Pivot, 0.330ID 1.76OD CAPSCREW, Hex Head, 5/16-18 x 1, G NUT, Hex Flange, Center Lock, 5/ GRIP PULLEY, Deck Idler CAPSCREW, Hex Head, 3/8-16 x 2, G NUT, Hex Flange, Whiz Lock, 3/ BELT GUIDE NUT, Hex Flange, Whiz Lock, 5/ NUT, Hex Flange, Whiz Lock, 5/ BELT GUIDE, Long NUT, Hex Flange, Whiz Lock, 5/ BELT, Deck (91.35" EL, HAA section) SPRING, Extension, BM 2 UPSTOP CAPSCREW, Hex Washer Head, 5/16-18 x 3/ WASHER, 5/ BM 1 BRACKET, Idler, Fixed CAPSCREW, Hex Head, 5/16-18 x 1, G NUT, Hex Flange, Whiz Lock, 5/ WASHER, Flat, 3/ BM 1 GUARD, Spring SHIM Footnotes: RD Series 33

33 96cm Mower Deck - Support Group 34 RD Series

34 96cm Mower Deck - Support Group Item Part No Qty Description BM 1 BRACKET, Rear Lift, LH BOLT, Carriage, Short Square Neck, 5/16-18 x 3/4, G COVER, Pulley BOLT, Carriage, Short Neck, 5/16-18 x 3/4, G NUT, Hex Flange, Whiz Lock, 5/ NUT, Push On, 5/ WASHER, 5/ BM 1 BRACKET, Front Connector RETAINER, Pin Spring NUT, Hex Lock, ESNA LIGHT, 1/ NUT, Hex Jam, 1/ BOLT, Carriage, 5/16-18 x 5/ WHEEL, Gauge BOLT, 3/8-16 x 2-3/ NUT, Hex Flange, ESNA, 3/ WASHER, 1/ BM 1 BRACKET, Deck, Rear BM 1 BRACKET, Rear Lift, LH BM 1 SUPPORT, Deck Front BM 1 BRACKET, Front Support BM 1 BRACKET, Front Upstop NUT, Hex Flange, Whiz Lock, 5/ BOLT, Carriage, Short Neck, 5/16-18 x 3/4, G WASHER, Spring,.30" ID BOLT, Shoulder, 5/16-18 x.13/16, 1/2" Thread Length NUT, Hex Flange, Whiz Lock, 5/ ROD, Latch BM 1 BRACKET, Front Hanger BOLT, 1/2 x 3 Footnotes: RD Series 35

35 107cm Mower Deck 36 RD Series

36 107cm Mower Deck Item Part No Qty Description YP 1 HOUSING, Spindle YP 2 BEARING, Ball YP 1 SHAFT, Spindle YP 2 SHIELD, Arbor YP 2 SPACER, Bearing YP 2 RING, Self Lock YP 1 SHAFT, Spindle, RH (LH Thread) YP 2 SHIELD, Arbor YP 2 SPACER, Bearing YP 2 BEARING, Ball YP 1 HOUSING, Spindle YP 2 RING, Self Lock SM 8 SCREW, Hex Washer Head, Taptite, 5/16-18 x 1-1/ YP 2 SPACER, Mower Drive YP 2 PULLEY, V, Deep Groove SM 4 WASHER, Spring, SM 1 CAPSCREW, Hex Head, 7/16-14 x 2-3/4, GR YP 1 CAPSCREW, Socket Head, 7/16-14 x 2-3/ BMYP 1 BLADE, RH, 21" YP 1 CAPSCREW, Socket Head, 7/16-14 x BMYP 1 BLADE, LH, 21" SM 1 CAPSCREW, Hex Head, 7/16-14 x 1, GR YP 2 ADAPTER, Washout Port SCREW, Thread Roll, 5/16-18 x 3/ SM 40 NUT, Flange, 5/16-18, GR BMYP 1 SUPPORT, Idler Arm BMYP 1 IDLER ARM SM 1 SPACER, Pivot, 5/16 ID x 1-3/4 OD X84MA 1 CAPSCREW, Hex Head, 5/16-18 x 1, GR X88MA 1 NUT, Hex Flange, Center Lock, 5/ YP 2 PULLEY, Deck Idler SM 2 CAPSCREW, Hex Head, 3/8-16 x 2, GR NUT, Hex Flange, 3/ YP 2 BELT GUIDE BMYP 1 BRACKET, Deck, Rear Lift, LH BOLT, Carriage, 5/16-18 x 3/4, GR SM 10 WASHER, Flat, 5/ MA 1 BELT GUIDE, LONG YP 1 BELT, " EL, HAA Section SM 1 SPRING, Extension YP 1 COVER, Pulley RETAINER, 5/16, GR YP 1 CENTER CAP BMYP 1 BRACKET, Idler, Fixed Footnotes: RD Series 37

37 107cm Mower Deck 38 RD Series

38 107cm Mower Deck Item Part No Qty Description BMYP 1 BRACKET, Front Connector SM 1 RETAINER, Pin Spring SM 1 NUT, Hex Lock, ESNA Light, 1/ SM 1 NUT, Hex Jam, 1/ SM 2 FITTING, Lube SM 2 WASHER, Flat, 3/ SM 2 WHEEL SM 2 BOLT, Wheel, 3/8-16 x 2-3/4, 3/4" Thread NUT, Hex Flange, ESNA, 3/ SM 2 WASHER, 1/ BMYP 1 BRACKET, Deck, Rear, RH BMYP 1 SUPPORT, Front BMYP 1 BRACKET, Front Upstop BMYP 1 DECK, 42" X3MA 2 WASHER, Spring, 1/ SM 4 BOLT, Shoulder, 5/16-18 x 1/ SM 1 ROD, Latch BMYP 1 BRACKET, Front Hanger YP 1 BOLT, 1/2 x YP 1 PULLEY, Idler CAPSCREW, Hex Head, 3/8-16 x 1-1/2, G BOLT, Shoulder, 5/16-18 x BMYP 1 BRACKET, Idler Mount BM 1 PLATE, Belt Guide Mount Footnotes: RD Series 39

39 Guard Group 40 RD Series

40 Guard Group Item Part No Qty Description AYP 1 GUARD, Middle Right AYP 1 GUARD, Middle Left YP 2 GUARD, Rear AYP 1 BRACE, Guard YP 1 GUARD, Front, LH YP 1 GUARD, Front, RH CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ SM 5 CAPSCREW, Hex Washer Head, Taptite, 1/4-20 x 1/ SM 5 WASHER, 1/4 Footnotes: RD Series 41

41 Collector Group Liter 42 RD Series

42 Collector Group Liter Item Part No Qty Description FRAME ASSEMBLY BOLT, Carriage, 1/4-20 X 5/8 (Included in Ref. 0010) A 1 FRAME, Upper (Included in Ref. 0010) A 1 SUPPORT, Dump Handle (Included in Ref. 0010) A 1 CROSS BRACE (Included in Ref. 0010) A 2 BRACKET, Mounting, Long (Included in Ref. 0010) A 1 SUPPORT STRAP, Dump Handle (Included in Ref. 0010) A 1 SUPPORT, Back, Frame (Included in Ref. 0010) A 1 BAGGER LOCATOR ASSEMBLY, LH (Included in Ref. 0010) A 1 BAGGER LOCATOR ASSEMBLY, RH (Included in Ref. 0010) NUT, Hex Flange, 1/4-20 (Included in Ref. 0010) CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 1-1/ NUT, Hex Flange, Serrated, 5/ CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ COVER, Transition CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ WASHER, 5/ SPRING, Extension CHUTE WASHER, 1/ CLIP, Hair Pin A 1 BACK PLATE A 1 BRACE, Lower Back Plate CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ PIN, Threaded Shoulder A 1 PLATE, Rotation, RH A 1 PLATE, Rotation, LH BOLT, Carriage, Short Neck, 5/16-18 x 3/4, G NUT, Hex Flange, Serrated, 5/ A 1 FRAME, Bagger SWITCH, Bag Full SCREW, Plastite, #10-14 x 7/ A 1 BRACKET, Bagger Latch A 2 LATCH, Bagger BOLT, Shoulder NUT, Hex Flange, Center Lock, 3/ A 1 PLATE, Switch BOLT, Carriage, 1/4-20 x 5/ NUT, Hex Flange, Whiz Lock, 1/ COVER, Bag Full Switch CAPSCREW, 5/16-18 x 3/ A 1 SUPPORT, Bagger, LH A 1 SUPPORT, Bagger, RH Footnotes: RD Series 43

43 Collector Group Liter 44 RD Series

44 Collector Group Liter Item Part No Qty Description CAPSCREW, Hex Flange Lock, 1/4-20 x 1-1/ NUT, Hex Flange, Lock, 1/ SCREW, Torx, 1/ SCREW, Hex Washer Head, Self Tap, 1/4-20 x 5/ BOLT, Carriage, 1/4-20 x 5/ NUT, Hex Flange, Whiz Lock, 1/ COVER, Collector, Red BAG, Collector ADJUSTER, Bagger Handle A 1 HANDLE, Bagger GRIP, Lift Rod A 1 HANDLE, Front A 1 HANDLE, Back A 2 STIFFENER Footnotes: RD Series 45

45 Collector Group Liter 46 RD Series

46 Collector Group Liter Item Part No Qty Description X82MA 25 BOLT, Carriage, 1/4-20 X 5/ BMYP 1 FRAME, Upper BMYP 1 SUPPORT, Dump Handle AYP 1 CROSS BRACE AYP 2 BRACKET, Mounting, Long BMYP 1 SUPPORT STRAP, Dump Handle AYP 1 SUPPORT, Back, Frame YP 1 BUSHING, Handle BMYP 1 BAGGER LOCATOR ASSEMBLY, LH BMYP 1 BAGGER LOCATOR ASSEMBLY, RH SM 25 NUT, Hex Flange, 1/ CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 1-1/ SM 10 NUT, Hex Flange, 5/ YP 1 COVER, Transition SM 4 WASHER, 5/ X75MA 2 SPRING, Extension YP 1 CHUTE SM 2 WASHER, 1/ SM 2 CLIP, Hair Pin BMYP 1 PLATE, Rotation, RH BMYP 1 PLATE, Rotation, LH BOLT, Carriage, Short Neck, 5/16-18 x 3/4, G AYP 1 FRAME, Bagger YP 1 SWITCH, Bag Full YP 2 SCREW, Plastite, #10-14 x 7/ AYP 2 LATCH, Bagger X39MA 2 BOLT, Shoulder X84MA 2 NUT, Hex Flange, Center Lock, 3/ AYP 1 PLATE, Switch X82MA 2 BOLT, Carriage, 1/4-20 x 5/ SM 2 NUT, Hex Flange, Whiz Lock, 1/ YP 1 COVER, Bag Full Switch BMYP 1 SUPPORT, Bagger, LH BMYP 1 SUPPORT, Bagger, RH BMYP 1 BACK PLATE ASSEMBLY X84MA 2 NUT, Hex Flange, Center Lock, 3/ MA 2 PIN, Threaded Shoulder AYP 1 BRACKET, Bagger Latch BACKPLATE BRACE, Lower Back Plate CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ BOLT, 5/16-18 x X94MA 1 CAPSCREW, Hex Flange Lock, 1/4-20 x 1-1/4 Footnotes: (Includes Ref. Nos , , , , & ) (Not a serviceable part. Order Ref. No. 0350) RD Series 47

47 Collector Group Liter 48 RD Series

48 Collector Group Liter Item Part No Qty Description X89MA 1 NUT, Hex Flange, Lock, 1/ YP 2 SCREW, Torx, 1/ YP 4 SCREW, Hex Washer Head, Self Tap, 1/4-20 x 5/ X82MA 8 BOLT, Carriage, 1/4-20 x 5/ SM 12 NUT, Hex Flange, Whiz Lock, 1/ YP 1 COVER, Collector, Red YP 1 BAG, Collector, 350L BMYP 1 HANDLE, Bagger YP 1 GRIP, Lift Rod YP 1 ADJUSTER, Bagger Handle AYP 1 HANDLE, Front AYP 1 HANDLE, Back BMYP 2 STIFFENER Footnotes: (Includes Ref. Nos , , , , & ) (Not a serviceable part. Order Ref. No. 0350) RD Series 49

49 Decal Group 50 RD Series

50 Decal Group Item Part No Qty Description YP 2 DECAL, Logo, Hood YP 1 DECAL, Roll Release YP 1 DECAL, Steering Wheel X511MA 1 DECAL, Drawbar Warning Symbol SM 1 DECAL, Discharge Tube Symbols SM 1 DECAL, Tunnel SM 2 DECAL, Danger Rotation Blade Symbols YP 1 DECAL, Cutting Width, 38" (96cm) YP 2 DECAL, Cutting Width, 42" (107cm) YP 1 DECAL, Battery X736MA 1 DECAL, Clutch/Brake SM 1 DECAL, Height of Cut YP 2 DECAL, RPX Series YP 2 DECAL, RXT Series YP 1 DECAL, Model, ERPX17538RDF YP 1 DECAL, Model, ERPX1838RDF YP 1 DECAL, Model, ERXT2242RDF YP 1 DECAL, Model, ERXT2642RDF Footnotes: RD Series 51

51 Electrical Group 52 RD Series

52 Electrical Group Item Part No Qty Description YP 1 WIRING HARNESS CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 5/ BATTERY, 12 Volt YP 1 CONTAINER, Battery BMYP 1 HOLD DOWN, Battery SM 1 BUZZER, Bag Full MA 1 SWITCH, Bagger YP 1 HARNESS, Bag Full SCREW, Hex Washer Head, Thread Roll, 5/16-18 x 3/ SM 1 BOLT, Hex Flange, 5/16-18 x 5/ SM 1 SOLENOID 0110 B4300GS 2 CAPSCREW, Hex Head, 1/4-20 x 1/ SM 1 PLUG, Hole YP 1 SWITCH, PTO SM 1 SWITCH, Reverse Mow YP 1 SWITCH, Light BMYP 1 SUPPORT, RMO Switch YP 1 SWITCH, Seat (Use on 22HP & 26HP Models) BOLT, Carriage, 5/16-18 x 3/4, GR SM 3 NUT, Flange, 5/16-18, GR YP 1 SWITCH, Push Button (NO/NC) YP 1 BATTERY CABLE SM 1 CABLE, #6 x SM 1 CABLE, # 6 x SM 2 NUT, Hex Lock, KEPS, 5/ SM 14 TIE, Self Lock SM 1 SWITCH, Push Button (NO) NUT, Flange, Serarated, 1/4-20, GR SM 2 KEY, No Mow SM 1 CLIP, Wire YP 1 PLUG, Dash YP 1 SWITCH, Seat (Use on 17.5HP & 18HP Models) SM 1 PLUG, Hole YP 1 SWITCH, Ingition YP 1 HARNESS, Headlight YP 1 PLUG, Starter Insert * FUSE, 20 Amp YP 1 KEY, Ingition, Blister Pack NUT, M5 x 0.8 Footnotes: Note* See your local hardware store for replacement fuses. RD Series 53

53 Electrical Group 54 RD Series

54 Electrical Group Item Part No Qty Description SCREW, M5 x 0.8 x WASHER, M5 Footnotes: Note* See your local hardware store for replacement fuses. RD Series 55

55

56 Parts Manual for Rear Discharge European Tractor RD Series IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough, GA, U.S.A Copyright 2013 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Revision: A 1/25/2013