Reproduction. Not for. 28" / 71cm REAR ENGINE RIDER EUROPEAN SERIES 24. Parts Manual for E BVE

Transcription

1 Parts Manual for 28" / 71cm REAR ENGINE RIDER EUROPEAN SERIES 24 Model No. Description E BVE Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough, GA, U.S.A Manual No Revision: - 4/23/2015

2

3 Table Of Contents PAGE GROUP 4 Wheels Group 6 Front End Group - Narrow 8 Engine Group B&S Main Case, LH Fender & Yoke Lift Group 14 Differential Assembly 18 Primary Chain Case 20 Mower Deck, Blade & Spindle Cover Group 22 Mower Belt, Brake & Interlock Group 24 Deck Rails & Lift Group 28 Spindle Assembly 30 French Guard Group Euro RER 32 Decals 34 Electrical Group 13.5 B&S ES 36 Wiring Schematic (for 13.5 & 14.5 HP Briggs) 28" / 71cm REAR ENGINE RIDER SERIES 24 3 Manual No TP RE-N

4 Wheels Group Manual No " / 71cm REAR ENGINE RIDER 4 SERIES 24

5 Wheels Group Item Part No Qty Description YP 2 ASSEMBLY, Front Wheel, 11x YP 2 ASSEMBLY, Rear Wheel, K358, 15x6.50-8, Kenda 02A YP 2 RIM, Extra Wide (For 16/7.50 x 8 Tire) SM 4 AIR VALVE STEM, Snap-In YP 2 LUBE FITTING, Straight (Press into 3/16 hole) YP 4 BEARING, Ball, Flanged (3/4 ID, 1-3/8 OD) SM 8 WASHER,.77 x 1.13 x.06, Flat PIN, 5/32 x 1 Cotter YP 2 HUBCAP YP 2 SEAL, Felt YP 2 CAP, Dust YP 2 TUBE, Inner (For 4.10/3.50 x 4 Tire) BOLT, Hex Washer, 1/2-20 X YP 1 CAP, Hub, R.H., 1.35 ID x YP 1 HUB, Rear Wheel, 3 Hole 3/4 ID, LH YP 1 HUB, Rear Wheel, 3 Hole 1.25 ID, RH YP 1 BOLT, 5/16-24 x 1-5/8 Tapered, Axle (Left Hand) YP 1 BOLT, 5/16-24 x 2 Tapered, Axle (Right Hand) NUT, 5/16-24, Hex Crown Lock,GR C, Zinc/Clear YP 1 CAP, Hub, L.H.,.975 ID x YP 1 CLAMP, 2 ID YP 1 SEAL, 1.22 ID x OD YP 1 CAP, Seal 1.0 ID x 1.67 OD Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES 24 5 Manual No

6 Front End Group - Narrow Manual No " / 71cm REAR ENGINE RIDER 6 SERIES 24

7 Front End Group - Narrow Item Part No Qty Description DYP 1 WELDMENT, Front Axle, Narrow, Red YP 1 ASSEMBLY, Steering Wheel (for 5/8 shaft) YP 1 LOGO, Steering Wheel, Snapper YP 1 ROLL PIN, 1/4 x 1-1/ YP 1 CLAMP, Tube YP 1 SCREW, 5/16-24 x 2-1/2 Hex Head Cap, GR NUT, 5/16-24 Hex Flange Lock, BZ YP 1 FOAM COVER, Steering Shaft YP 1 COVER, Steering Shaft YP 1 PIN, 3/16 x 1 Cotter YP 3 WASHER,.66 x 1.31 x.09 Flat YP 1 BUSHING, Nylon RETAINING RING, 3/4 ID, ZC/CL YP 1 BUSHING, Nylon YP 4 BEARING, Nylon YP 1 RING, 1/2 External Retaining YP 1 SPRING, Parking Brake Latch YP 1 HAIR PIN, 2-1/ YP 1 LATCH, Parking Brake YP 2 FOOT PAD, Short (5.5 x 4.7) BMYP 1 WELDMENT, Clutch Pedal YP 1 PAD, Pedal SCREW, 1/4-20 x 3/4 Hex Head Cap, GR 5, Zinc/Clear YP 2 CONNECTOR, Cable (Single Part) NUT, 1/4-20, Center Lock, GR 5, Zinc/Clear YP 1 CABLE, Brake, Snap-In YP 1 CABLE, Clutch/Brake, long YP 4 BUSHING, Tie Rod WASHER. Flat, 3/ BMYP 1 WELDMENT, King Pin, Left Hand, Black BMYP 1 WELDMENT, King Pin, Right Hand, Black YP 2 CAP, Dust BMYP 1 WELDMENT, Steering Shaft, Black PIN, 3/16 x 1-1/2 Cotter PIN, 5/32 x 1 Cotter PIN, 1/8 X 0.75, Cotter, Zinc/Clear YP 1 TIE ROD, Left Hand (7.41 long) YP 1 TIE ROD, Right Hand (7.41 long) SM 6 WASHER,.77 x 1.13 x.06, Flat Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES 24 7 Manual No

8 Engine Group B&S 3130 Manual No " / 71cm REAR ENGINE RIDER 8 SERIES 24

9 Engine Group B&S 3130 Item Part No Qty Description YP 1 SEAT KIT, Operator (12 tall) (Milsco V-3405 Series - Plastic Back) (includes seat + # bolts) YP 1 SWITCH, Seat, Push Button (NC - Gray) BOLT, Carriage, 5/16-18 x 1 G BMYP 2 PLATE, Seat Adapter RETAINER, 5/16 X.625, Push Nut, GR 5, Zinc/Clear SCREW, 5/16-18 X.750, Flanged Whiz-Lock, GR SM 1 SCREW, 3/8-16 x 5/8 Hex Washer Self-Tap, BP SHIELD, Manifold, RER SM 2 SET SCREW, 5/16-18 x 3/4 Socket Head, GR8, BZ YP 1 MUFFLER, W/Guard, RER, B&S SCREW, 1/4-20 x 5/8, Hex Washer Head, Thread Roll, Zinc/Clear SM 1 GASKET, Exhaust SM 1 ASSEMBLY, Oil Drain Valve, Long SPACER,.328 ID X.623 OD X.151 Thick YP 2 SCREW, 5/16-24 X 1.75, Hex Head Cap, GR5, Zinc/Clear YP 1 ASSEMBLY, Gas Tank, W/Gage YP CAP, Fuel Tank w/gage B 2 CLAMP,.490 ID,.312 Wide, Fuel Hose, Band Type, Green YP 1 HOSE, Fuel,.25 ID,.5 OD, 8.50 LG, Low Perm YP 1 HOSE, Fuel, 1/4 ID X 3 Long S 1 FILTER, Fuel, In-Line WSHR, 5/16, GR5, FLAT, ZINC/CLEAR HHCS,5/16-24X2.000,GR5,ZINC/CLEAR WASHER, 5/16, Flat SAE, Zinc/Clear WASHER, 5/16 Split Lock, YZ NUT, 5/16-24, Hex, GR5, Zinc/Clear YP 1 DRIVE DISC, Steel, (4.56 P.D., 5.75 O.D. Pulley) YP 2 SCREW, 3/8-16 x 3/8 Hex Recess Set KEY, 1/4 Square x 2 Long BMYP 1 GUIDE, Belt, 1/4 Wire, 1.85 X 4.74 ID, 3.72 Tall, 5.74 Mount YP 1 CONTROL, Throttle (23.6 long) (Briggs Engines) DYP 1 PLATE, Throttle Control, Red SCREW, x 1/2 Hex Washer Self-Tap, Torx, ZC/CL SCREW, 1/4-20 X.500, Hex HD, Self-Tap, Zinc/Clear NUT, 5/16-18 Large Flange Center Lock, ZC/CL YP 2 KNOB, 5/16-18, Handle, Fluted 5 Prong, Black 46 21R B1 1 * ENGINE, Intek Series 3130, B&S, Euro, 21R B1 Footnotes: Note: * Purchase engine parts from engine manufacture dealer. 28" / 71cm REAR ENGINE RIDER SERIES 24 9 Manual No

10 Main Case, LH Fender & Yoke Lift Group Manual No " / 71cm REAR ENGINE RIDER 10 SERIES 24

11 Main Case, LH Fender & Yoke Lift Group Item Part No Qty Description DYP 1 WELDMENT, Main Case (Standard), Red YP 1 FENDER, ID Hole, LH, RER PIN, Hair, 3/32 x 1.6, GR5, Zinc/Clear YP 2 SCREW, 5/16-18 x 3/4 Hex Washer Self-Tap SM 2 SWIVEL, Adjustable, 5/ hole DYP 2 WING, Rear, Red SCREW, 5/16-18 X.750, Flanged Whiz-Lock, GR WASHER, 5/16, Flat SAE, Zinc/Clear BMYP 1 BUMPER, Rear, Black SM 2 SCREW, 3/8-16 x 5/8 Hex Washer Self-Tap, BP SCREW, 5/16-18 x 1-1/2 Hex Washer Self-Tap YP 1 COVER, Battery YP 1 COVER, Solenoid YP 6 FASTENER, 1/4 x 3/4 Ratchet DYP 1 BRACKET, Belt Adjuster, Red YP 1 TIE ROD, (5/16-24 thread- both ends) YP 1 BUSHING, Pivot, 1.89X5.88X BMYP 1 BRACKET, Switch, Black SCREW, #10-32 x 3/8, Torx Hex Washer Head Self-Tap, ZC/CL SCREW, 5/16-24 x 1 Hex Head Cap, GR 5, BZ NUT, 5/16-24, Hex Crown Lock,GR C, Zinc/Clear YP 1 YOKE YP 1 COLLAR, Yoke YP 2 BEARING, Yoke SM 2 WASHER, 5/16 I.D. 1 O.D. Fender YP 1 SPRING, Clutch / Brake PIN, 3/32 X 3/4, GR5, Cotter, Zinc/Clear WASHER, 3/8 (.406 X.816 X.65), Flat, Zinc/Clear BMYP 1 SLIDE, Drive Support, Black BOLT, 5/16-18 x.530 Shoulder, GR 2, Zinc/Clear YP 2 SLIDE HALF NUT, 5/16-18, Serated Lock Flange, GR5, Zinc/Clear BMYP 1 BRACKET, Drive Support WASHER,.32 X.58 X.08, Split Lock, YZ NUT, 5/16-18, GRB, Zinc/Clear YP 1 STUD, Clutch Link (3/8-24 thread) YP 1 ARM, Yoke WASHER, 3/8 Internal Tooth Lock, BZ NUT, 3/8-24, Hex, Grade 5, YZ YP 1 ASSEMBLY, Leaf Spring 41 B4300GS 1 SCREW, 1/4-20X.500, Hex HD, Self-Tap, Zinc/Clear SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/ SM 2 WASHER, 5/16, Internal Lock, Zinc/Clear YP 2 CLIP, Wire 7/16 Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

12 Main Case, LH Fender & Yoke Lift Group Manual No " / 71cm REAR ENGINE RIDER 12 SERIES 24

13 Main Case, LH Fender & Yoke Lift Group Item Part No Qty Description YP 1 NUT, 5/16-24 Hex Flange Lock, ZP SCREW, 5/16-18 x 3/4 Hex Head Cap, GR 5, YZ YP 1 CLAMP, 2 ID YP 2 BOOT, Rear Axle, Thick Flange YP 1 WASHER, Thrust, (Hex Flanged) YP 2 WASHER, Thrust, (.765 ID, OD)(Nylon) YP 1 WASHER, Notched Shim, Nylon (Can make from ) YP 1 BRACE, CROSS BMYP 1 WELDMENT, Shift Arm, Black YP 1 SHIFT LINK, Long (5/16-24 both ends) YP 1 SHIFT LINK, Short (1.44 Long, 5/16-24 thread) NUT, 5/16-24, Hex, GR5, Zinc/Clear YP 1 ASSEMBLY, 3/4 DX Axle Bearing, (Includes , , & ) YP 2 BEARING, 3/4 ID, DX YP 1 FITTING, Lube, 45 Degree, 3/16 w/hex (long shank) YP 1 SEAL,.750X1.25X.25, Dust / Grease Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

14 Differential Assembly Manual No " / 71cm REAR ENGINE RIDER 14 SERIES 24

15 Differential Assembly Item Part No Qty Description YP 1 FENDER, RH, Hole, RER YP 1 GASKET, Transmission Case NUT, 5/16-24, Serated Flange, Zinc/Clear, GR SCREW, 5/16-18 X.625, Hex Washer Head, Thread Roll, Zinc/Clear SCREW, 1/4-20 x 5/8, Hex Washer Head, Thread Roll, Zinc/Clear YP 1 BEARING, Axle, ID, OD, PM YP 1 WASHER, Thrust (1.37 ID, OD) YP 4 BOLT, 5/16-24 x 1-5/8 Hex Nylock, G5, Black YP 1 PLATE, Differential, Heat Treated (8 holes) YP 4 SPACER, Pinion YP 4 GEAR, Differential Pinion (12T, 12P) YP 1 GEAR, 63 Tooth 10 Pitch (4 Hole) YP 1 ASSEMBLY, Short Axle, 23T YP 1 SPACER, Differential (1.25 ID x.425 Wide) YP 1 KIT, 23 Tooth Long Axle & Spacer (Includes Axle & Spacer ) YP 1 WASHER, Thrust, (Hex Flanged) YP 1 ASSEMBLY, Drive Hex Tube 13.2 Long YP 1 WASHER, Nylon YP 2 O-RING, 5/ YP 2 WASHER, 5/16 X 5/8 X.05, Belleville YP 1 GEAR, 11 Tooth, 10 Pitch, PM YP 1 SPROCKET, 34T, 3/8P YP 1 RING, 1-3/16 External Retaining YP 1 CHAIN, 46 Pitch (#35 Endless) YP 1 SPACER,.50 OD X.031 ID X 1.75 Long, Heat Treated YP 1 CASE, Transmission YP 3 PLUG, 3/ WASHER, External Tooth, 5/ WASHER, 5/16, Flat SAE, Zinc/Clear YP 1 SCREW, 5/16-24 x 2-5/8 Hex Head Cap, ZP YP 2 BOOT, Rear Axle YP 2 CLAMP, 2 ID YP 1 GRIP, Shift Handle YP 1 WELDMENT, Shift Handle PIN, 3/32 X 3/4, GR5, Cotter, Zinc/Clear YP 1 PIN,.25 X 1.25, Clevis YP 1 BUSHING, 3/4 ID, 1.62 Flange (Nylon) YP 2 WASHER, Thrust.76 ID, 1.62 OD,.025 Thick NUT, 5/16-18, Hex Nylock, Zinc/Clear YP 1 SPEED ADJUSTMENT LATCH ASSY YP 1 SPRING YP 1 SPRING, Shift Detent YP 1 BUSHING, 3/4 ID, 1 Flange (Nylon) YP 1 WELDMENT, Shift Arm Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

16 Differential Assembly Manual No " / 71cm REAR ENGINE RIDER 16 SERIES 24

17 Differential Assembly Item Part No Qty Description SM 1 FITTING, Lube (Straight press fit for.187 hole, n WASHER,.32 X.58 X.08, Split Lock, YZ NUT, 5/16-24, Hex, GR5, Zinc/Clear YP 1 LEVER, Over-Ride WASHER,.922 X.065 X.065, Flat, Zinc/Clear BOLT, 5/16-18 X.750, Hex Washer Head Shoulder, Zinc/Clear YP 1 GREASE, 00 (Not Shown) YP 1 KIT, Differential Assembly (Not Shown) YP 1 KIT, Long & Short Axle (Includes items 13, 14, & 15) Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

18 Primary Chain Case Manual No " / 71cm REAR ENGINE RIDER 18 SERIES 24

19 Primary Chain Case Item Part No Qty Description YP 1 ASSEMBLY, Primary Chain Case (Contains all except Rubber Disc and Brake related parts) YP 1 KEY, #5 (1/8 x 5/8) Woodruff YP 1 SPRING, Brake Return Torsion NUT, 1/4-28 Hex Top Lock, GR 5, BZ (Was ) YP 1 CHAIN, 46 Pitch (#35 Endless) YP 1 SPACER, Brake Arm Pivot (.265 ID,.375 OD,.418 long) YP 2 WASHER, Thrust, Nylon YP 1 WELDMENT, Sprocket & Shaft YP 2 O-RING, 1/2 x 5/8" YP 1 GASKET, Primary Chain Case YP 1 SCREW, 1/4-28 X 1, Hex HD, GR5 BZ YP 1 WELDMENT, Hub & Sprocket SM 10 SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx), Zinc/Clear SM 2 WASHER, Belleville.64 x x YP 1 WASHER, Wave.625 x YP 1 WELDMENT, Primary Chain Case Half, RH YP 2 BEARING, Ball 5/8 ID x 1-3/8 OD YP 1 RING, 1/2 External Retaining YP 2 BEARING, Needle ID x OD x.5 Wide YP 1 ROLLER, 1-3/8 Long YP 1 COVER, Primary Chain Case, LH YP 1 PLUG, 3/4" NUT, 5/8-18, Nylon Insert Lock, Zinc/Clear YP 1 KIT, Smooth Clutch Assembly YP 1 WASHER, Thrust YP 1 PLATE, Smooth Clutch YP 1 DRIVEN DISC, Rubber, Smooth Start Clutch YP 1 ASSEMBLY, Driven Hub & Cup (Incl. Ref ) NUT, 5/16-24 Hex Flange Lock, BZ SCREW, 5/16-24 x 1-1/8 Rib Neck, GR 5 (Not Shown) YP 1 ASSEMBLY, Brake Lever & Pad Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

20 Mower Deck, Blade & Spindle Cover Group Manual No " / 71cm REAR ENGINE RIDER 20 SERIES 24

21 Mower Deck, Blade & Spindle Cover Group Item Part No Qty Description SM 3 WASHER,.77 x 1.13 x.06, Flat YP 1 RING, 2 ID x 3/4 High, Tolerance YP 1 COVER, Spindle WASHER, 5/16, Flat SAE, Zinc/Clear YP 2 SCREW, 1/4-20 x 3-1/2 Hex Head w/free Spinning Wa SCREW, 1/4-20 x 5/8, Hex Washer Head, Thread Roll, Zinc/Clear BOLT, 5/16-18 x 3/4, Carriage, Short Neck, G5, Zin YP 2 SCREW, 1/2-20 x 1-1/4 Hex Head Cap, GR YP 2 WASHER, 1/2 Internal Tooth Lock, BZ BOLT, 3/8-16X0.75, Serrated Flange, GR5, Zinc/Clea YP 1 ASSEMBLY, Mulching Cover, RER, NUT, Hex Flange, 3/ SCREW, 5/16-18 x 7/8 Hex Head Cap, GR 5, Zinc/Clea YP 2 NUT, 1/2-20 Hex, GR 5 ZP RETAINER, 5/16 X.625, Push Nut, GR 5, Zinc/Clear NUT, 5/16-18, Flange Nylock, GR F, Zinc/Clear YP 1 KIT, Deck Replacement, 28 w/anti-scalp, Red BZYP 1 BLADE, 28 (Standard 3 Hole Air Lift) YP 1 CHUTE, Side Discharge, 28 / WASHER,.325 ID X.850 OD X.041 Thk, Internal External Lock, Type A, ZC/CL Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

22 Mower Belt, Brake & Interlock Group Manual No " / 71cm REAR ENGINE RIDER 22 SERIES 24

23 Mower Belt, Brake & Interlock Group Item Part No Qty Description SM 1 NUT, 3/4-16 Hex Jam, GR YP 1 BELT, Spindle Drive (72.75 AA Section, Kevlar) SM 2 WASHER, 49/64x1-1/2x.06, Flat YP 1 PULLEY, Deck Spindle, 6.95 OD YP 1 HUB, Pulley, PM WASHER, 3/8 (.406 X.816 X.65), Flat, Zinc/Clear YP 1 KIT, Brake Band, 10.1 L, 1.25 H (Formed) WASHER, 1/4, Flat, GR5 Zinc/Clear YP 1 BUSHING, Flanged,.27 ID, Nylon, Black YP 1 SPRING, Rectangular Wire Die, Blue NUT, 1/4-20 Hex Top Lock, Zinc/Clear YP 1 PIN, 1/4 x 1-5/8 Clevis PIN, 3/32 X 3/4, GR5, Cotter, Zinc/Clear YP 1 EYE-BOLT, 1/4-20 x YP 1 SPACER,.31 I.D. x.39 O.D. x 1 Nylon YP 1 DRUM, Brake Spindle (3 OD, 1.6 Tall) YP 2 RING, 2 External Retaining YP 1 SPRING, Extension, 4 x 1/2 Diameter WELDMENT, Idler Arm, RER SCREW, 3/8-16 X 1.50, Hex HD Cap, GR5, Zinc/Clear YP 1 RESTRICTOR, Belt, 2.18 w/lock YP 1 PULLEY, Idler,.375 ID, 4 OD NUT, 3/8-16, Nylock, GR5, Zinc/Clear YP 1 SCREW, #10F X1, GR2, Hex Washer Self-Tap, ZP YP 1 SWITCH, Deck Interlock (NO) YP 1 MOUNT, Handle/Switch YP 1 ROD, Idler Control YP 1 SPRING, Blade Handle YP 1 WELDMENT, Blade Engagement Handle YP 1 SPRING, Torsion, Flip Handle YP 1 PIN, 3/16 x 1 Clevis BMYP 1 HANDLE, Blade Engagement (Flip) YP 1 GRIP, Handle SCREW, 1/4-20 x 5/8, Hex Washer Head, Thread Roll, Zinc/Clear Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

24 Deck Rails & Lift Group Manual No " / 71cm REAR ENGINE RIDER 24 SERIES 24

25 Deck Rails & Lift Group Item Part No Qty Description YP 1 RAIL, Deck Lift, Left Hand YP 1 RAIL, Deck Lift, Right Hand YP 2 BOLT, 1/4-20 x 1/2 Hex Flange Lock, GR 5, ZP NUT, 5/16-18 Hex Flange Lock, GR 5, YZ YP 1 CLUTCH PLATE ASSY, RLM YP 1 SPRING, Latch,.072 DIA., 3.6 Long SM 3 SCREW, 3/8-16 x 5/8 Hex Washer Self-Tap, BP SCREW, 5/16-18 X.625, Hex Washer Head, Thread Roll, Zinc/Clear YP 1 BRACE, Top Rail YP 1 GUIDE, Belt ANCHOR WASHER, 5/16, Internal Lock, Zinc/Clear NUT, 5/16-24, Hex, GR5, Zinc/Clear SCREW, 5/16-24 x 3/4 Hex Head Cap, GR YP 2 SPRING, Assist YP 1 BOLT, #10-24 x 1 Flat Head Square Neck NUT, #10-24, Hex Nylock, GRB, Zinc/Clear YP 2 RING, Rear Lift Arm (Blue) YP 1 PIVOT, Leveling WASHER, 3/8 (.406 X.816 X.65), Flat, Zinc/Clear NUT, 3/8-24, Hex Nylock, Zinc/Clear YP 1 WELDMENT, Rear Lift Arm ADJUSTER, Chain (5/16-18 X 3.68 ) SM 2 SWIVEL, ADJUSTABLE, 5/ hole PIN, Hair, 3/32 x 1.6, GR5, Zinc/Clear YP 1 GRIP, DECK LIFT YP 1 LEVER, Height of Cut YP 1 SPRING, Lever SCREW, 3/8-24 x 1-3/4 Hex Head Cap, GR SM 2 WASHER, 13/32 ID x 1.25 x 1/8 Thick, Flat, ZP YP 2 SPACER, Deck Lift NUT, 3/8-24 Hex Center Lock, GR B, YZ YP 1 SPACER, Detent YP 1 DETENT, Height Adjust SCREW, 3/8-16 X 1.0, Hex Washer Self-Tap, ZC/CL YP 1 CABLE ASSEMBLY, No Reverse in Mow YP 1 RING,.438 External Retaining YP 2 RING, Front Lift Arm (Red) YP 1 WELDMENT, Front Lift Arm PIN, 1/8 X 0.75, Cotter, Zinc/Clear YP 1 ROD, Leveling (3/4-24 thread) BOLT, 5/16-18 x 5/8 Hex Flange lock, GR 5, YZ YP 1 ARM, Front Lift YP 1 ROD, Deck Support (Front Lift Arm to Front End) Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

26 Deck Rails & Lift Group Manual No " / 71cm REAR ENGINE RIDER 26 SERIES 24

27 Deck Rails & Lift Group Item Part No Qty Description YP 1 BOLT, 3/8-24 X 9/16, 1/2 Dia. Shoulder, ZP WASHER,.531 ID X OD X.094 Thk, Flat, ZC/CL YP 1 SPRING, Pedal YP 1 FOOT PEDAL, Blade Stop Control NUT, 1/4-20 Hex Flange Lock, GR 5, Zinc/Clear YP 1 CLIP, Cable BOLT, 1/4-20 x 3 x 3/4 Square Neck Carriage, GR YP 1 SHOULDER BOLT, 3/8-24 w/nylon Patch, GR 5 Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

28 Spindle Assembly Manual No " / 71cm REAR ENGINE RIDER 28 SERIES 24

29 Spindle Assembly Item Part No Qty Description SM 1 WASHER,.77 x 1.13 x.06, Flat SM 2 RING, 1.85, Internal Retaining SM 2 BEARING, Ball, 1.78 OD,.750 ID,.610 Wide SM 1 WASHER, Spindle,.75 ID, 1.75 OD,.28 Thick, PM YP 1 HOLDER, Blade (3 Hole) BMYP 1 WELDMENT, Spindle Housing, 7.5 Tall YP 1 SPACER, Blade Centering (.63 X 1.05 X.094) YP 1 SPINDLE, Rider ( overall length) YP 1 NUT, 5/8-18 Hex Center Lock Jam, GR5, ZP Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

30 French Guard Group Euro RER Manual No " / 71cm REAR ENGINE RIDER 30 SERIES 24

31 Item Part No Qty Description YP 3 PLUG, 1 Hole WASHER, 5/16, Flat SAE, Zinc/Clear SCREW, 3/8-16 X.750,Washered Thread Roll, ZC/CL BOLT, 1/4-20 X.75, Carriage, GR5, Zinc/Clear NUT, 1/4-20 Hex Flange Lock, GR 5, Zinc/Clear YP 1 ASSEMBLY, Guard Wire Form, Euro BMYP 1 GUARD, Front Main Case, Euro, RER-Black BMYP 1 GUARD, Rear Main Case, Euro, RER-Black BMYP 2 GUARD, Strap, Euro, RER-Black X3MA 2 SCREW, 1/4-20 X 1, Thread Forming SM 1 BOLT, 1/4-20 X.750, Hex Flanged Cap, GR5, Zinc/Clear French Guard Group Euro RER Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

32 Decals Manual No " / 71cm REAR ENGINE RIDER 32 SERIES 24

33 Decals Item Part No Qty Description YP 1 DECAL, 72cm (28 Inch) (Hi-Vac) YP 1 DECAL, Clutch Brake YP 1 DECAL, Height-Of-Cut, Symbol, RER YP 1 DECAL, SNAPPER/w Turtle YP 1 DECAL, Symbol, Blade/Belt Part #'s YP 3 DECAL, Deck Symbols- International YP 1 DECAL, Remove Battery, Symbols, Euro YP 1 DECAL, Battery Orientation, Euro RER YP 1 DECAL, Caution, Fuel Leakage YP 1 DECAL, SAFETY/RMO, ERER YP 1 DECAL, Blade Caution, Euro RER YP 1 DECAL, ID, Parking Lock YP 2 LABEL, Equip. Soley for Export, Exempt YP 1 DECAL, Reverse Lockout, RER DECAL, ID Tag, Model/Serial # (Not a Sellable Item) Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

34 Electrical Group 13.5 B&S ES Manual No " / 71cm REAR ENGINE RIDER 34 SERIES 24

35 Electrical Group 13.5 B&S ES Item Part No Qty Description YP 1 SWITCH, Seat, Push Button (NC - Gray) TIE, 7, Self Locking RETAINER, 1/4, Pushnut YP 1 SWITCH, Deck Interlock (NO) YP 1 SWITCH, DP, NO/NC, Snap-In SM 1 SWITCH, Ignition-Afterfire Solenoid YP 1 NUT, 5/8-32 Hex YP 1 CABLE, Battery, 8 Gauge, Black, 14, 1/4 Terminals YP 1 HARNESS, (Deck Interlock Wiring) YP 1 INTERLOCK MODULE, Briggs YP 1 WIRE HARNESS, B&S (13.5, 14.5 & 17.5) NUT, 1/4-20, Center Lock, GR 5, Zinc/Clear SM 1 BOOT, Insulator, Battery Termnal, Red YP 1 HOLDER, Fuse YP 1 FUSE, Round 10 Amp (Not shown) YP 1 WIRE, Positive, 17 Long, 8 AWG, 1/4 Terminal Holes, Red YP 1 WIRE HARNESS, Starter WASHER, 1/4 Internal Tooth Lock, YZ NUT, 1/4-20, G5 Zinc/Clear YP 1 SOLENOID, 12V, Super Trombetta, RER YP 1 KEYS, Blister Pk (Kids+MWRS Don't Mix) English/French (set of two, one coated) SM 1 KEY, Ignition Indak (Set of 2) One Coated YP 1 WIRE HARNESS, Ignition Switch, 13.5, 14.5, 17.5 B&S YP 1 SCREW, #10-32 x 1 Hex Washer Head Self-Tap SCREW, 1/4-20 X.500, Hex HD, Self-Tap, Zinc/Clear SM 1 WASHER, 5/8 Internal Tooth Lock YP 1 FASTENER, 1/4 x 3/4 Ratchet BMYP 1 BRACKET, Battery, RER NUT, #10-24, Hex Flanged Whiz Lock, ZC YP 1 BOLT, #10-24 X 3/4, Carriage, GR2, YZ YP 1 BATTERY, 12V 20HR, 190CCA SCREW, 1/4-20 X 0.625, Hex Head Cap, GR5, Zinc/Clear Footnotes: 28" / 71cm REAR ENGINE RIDER SERIES Manual No

36 Wiring Schematic (for 13.5 & 14.5 HP Briggs) Manual No " / 71cm REAR ENGINE RIDER 36 SERIES 24

37 Wiring Schematic (for 13.5 & 14.5 HP Briggs) Item Part No Qty Description * Wiring Schematic incl. harness #'s , , & Footnotes: NOTE: * For harness # image & description see: Electrical Group (For 13.5 HP Briggs) page. 28" / 71cm REAR ENGINE RIDER SERIES Manual No

38

39

40 Parts Manual for 28" / 71cm REAR ENGINE RIDER EUROPEAN SERIES 24 IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough, GA, U.S.A Copyright 2015 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Manual No Revision: - 4/23/2015