NEW. High Pressure filters. FMM 150 series. Maximum pressure up to 420 bar - Flow rate up to 250 l/min
|
|
- Diane Harrell
- 5 years ago
- Views:
Transcription
1 NEW High Pressure filters FMM 50 series Maximum pressure up to 0 bar - Flow rate up to 50 l/min PASSION TO PERFORM
2 FILTER SIZING THE CORRECT FILTER SIZING HAVE TO BE BASED ON THE TOTAL PRESSURE DROP DEPENDING BY THE APPLICATION. THE MAXIMUM TOTAL PRESSURE DROP ALLOWED BY A NEW AND CLEAN HIGH PRESSURE PRESSURE FILTER HAVE TO BE IN THE RANGE bar. The pressure drop calculation is performed by adding together the value of the housing with the value of the filter element. The pressure drop pc of the housing is proportional to the fluid density (kg/dm ); all the graphs in the catalogue are referred to mineral oil with density of 0.86 kg/dm. The filter element pressure drop pe is proportional to its viscosity (mm /s), the corrective factor Y have to be used in case of an oil viscosity different than 0 mm /s (cst). Sizing data for single filter element, head at top pc = housing pressure drop [bar] pe = element pressure drop [bar] Y = Corrective factor Y (see correspondent table), depending on the filter type, on the filter element size, on the filter element lenght and on the filter media Q = flow rate (l/min) V reference oil viscosity = 0 mm /s (cst) V = operating oil viscosity in mm /s (cst) element pressure drop calculation with an oil viscosity different than 0 mm /s (cst) pe = Y : 000 x Q x (V:V) p Tot. = pc + pe Verification formula p Tot. p max allowed Maximum total pressure drop ( p max) allowed by a new and clean filter Application Range (bar) Suction filters Return filters Low & Medium Pressure filters High Pressure filters Stainless Steel filters return lines lubrication lines off-line in power systems off-line in test benches over-boost Calculation: pc = 0. bar (see graphic below) p bar Δ housings p pressure drop. The curves are plotted using mineral oil with density of 0.86 kg/dm in compliance with ISO 968. p varies proportionally with density. pe = (5.9 : 000) x 0 x (6 : 0) =.09 bar FMM50 corrective factor Corrective factor Y to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference oil viscosity 0 mm /s Absolute filtration Nominal filtration element N - R Series Type A0 A06 A0 A6 A5 M5 HP 50 * FMM Flow rate l/min p Tot. = =.9 bar / The selection is correct because the total pressure drop value is inside the admissible range for high pressure filters. In case the allowed max total pressure drop is not verified, it is necessary to repeat the calculation changing the filter lenght. FMM50 calculation example Application data: High pressure filter Pressure Pmax = 00 bar Flow rate Q = 0 l/min Viscosity V = 6 mm /s (cst) Oil density = 0.86 kg/dm Required filtration efficiency = 5 μm with absolute filtration With bypass valve and / inlet connection
3 Corrective factor FILTER SIZING Corrective factor Y to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference oil viscosity 0 mm /s High pressure filters element Type HP 0 A Absolute filtration N - R Series A06 A0 A A Nominal filtration M HP HP HP HP HP HP HP element Type A0 Absolute filtration A06 A0 A6 A5 Nominal filtration M5 HF Recommended maximum flow rate for complete FMM50 filter - Pressure drop of complete filter = p.5 bar - Reference oil viscosity 0 mm /s (cst) - Oil density 0.86 kg/dm - Connections of filter under test G / lenght A Flow rate (l/min) Filtration rating A06 A A6 6 5 A
4 FMM50 Technical data GENERAL INFORMATION High Pressure filters Maximum pressure up to 0 bar - Flow rate up to 50 l/min housing materials - Head: Painted cast iron - Housing: Painted steel - Bypass valve: Steel Bypass valve - Opening pressure 600 kpa (6 bar) - Other opening pressures on request. Seals - Standard NBR series A - Optional FPM series V Pressure - Working pressure: MPa (0 bar) - Test pressure: 6 MPa (60 bar) - Burst pressure: 6 MPa (60 bar) - Pulse pressure fatigue test: cycles with pressure from 0 to MPa (0 bar) p element type - Microfibre filter elements - series N: 0 bar - Wire mesh filter elements - series N: 0 bar - Fluid flow through the filter element from OUT to IN Temperature From -5 C to +0 C Connections In-line Inlet/Outlet Note FMM 50 filters are provided for vertical mounting Weights [kg] and volumes [dm ] Weights [kg] Lenght 5 FMM Lenght Volumes [dm ] Hydraulic symbols Style S Style B Pressure drop The curves are plotted using mineral oil with density of 0.86 kg/dm in compliance with ISO 968. p varies proportionally with density. housings p pressure drop Bypass valve pressure drop.50 FMM 50 FMM / 0 Δ p bar p bar 0.50 Δ Flow rate l/min Flow rate l/min
5 FMM50 Designation & Ordering code COMPLETE FILTER Series and size Configuration example: FMM50 B A D M5 N P0 FMM50 Length Valves S B Seals A V Without bypass With bypass 6 bar NBR FPM Connections C G D G / E NPT F / NPT G SAE 6-5/6 - UN H SAE 0-5/8 - UN Connection for differential indicator Without connection Upper connection Frontal connection Filtration rating (filter media) A0 Inorganic microfiber µm A06 Inorganic microfiber 6 µm A0 Inorganic microfiber 0 µm A6 Inorganic microfiber 6 µm A5 Inorganic microfiber 5 µm M5 Wire mesh 5 µm Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized FILTER ELEMENT Element series and size HP50 Configuration example: HP50 M5 A N P0 Element length Filtration rating (filter media) A0 Inorganic microfiber µm A06 Inorganic microfiber 6 µm A0 Inorganic microfiber 0 µm A6 Inorganic microfiber 6 µm A5 Inorganic microfiber 5 µm M5 Wire mesh 5 µm Seals A V NBR FPM Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized Differential indicators DEA Electrical differential indicator DEM Electrical differential indicator DLA Electrical / visual differential indicator DLE Electrical / visual differential indicator ACCESSORIES DTA DVA DVM Visual differential indicator Electronic differential indicator Visual differential indicator Additional features T Plug
6 FMM50 Dimensions FMM50 length Connections C-D E-F-G-H H [mm] R M0 /8 UNC Recommended clearance space for maintenance
7 FMM50 SPARE PARTS Order number for spare parts d e a b c f Item: series FMM 50 Q.ty: pc. Q.ty: pc. Seal Kit code number element NBR FPM See order table Q.ty: pc. (a f) Indicator connection plug NBR FPM TH TV All data, details and words contained in this publication are provided for information purposes only. MP Filtri reserves the right to make modifi cations to the models and versions of the described products at any time for both technical and / or commercial reasons. The colors and the pictures of the products are purely indicative. Any reproduction, partial or total, of this document is strictly forbidden. All rights are strictly reserved.
8 WORLDWIDE NETWORK HEADQUARTERS MP Filtri S.p.A. Via Maggio, 0060 Pessano con Bornago Milano - Italy BRANCH OFFICES MP Filtri U.K. Ltd. Bourton Industrial Park Bourton on the Water GL5-HQ Gloucestershire MP Filtri Canada Inc. 88 Keele Street Concord, Ontario LK N - Canada MP Filtri Germany GmbH Hans-Wilhelmi-Straße DE-6686 St. Ingbert ITALFILTRI LLC Russian Federation Yurievsky Pereulok a, Building 00 Moscow - Russia MP Filtri France SAS Parc d activités des Chanteraines 8 rue du Commandant d Estienne d Orves Immeuble D 990 Villeneuve la Garenne MP Filtri (Shanghai) Co., Ltd. 80 Lianxi Road, Bld 8 - nd Floor Shanghai - Pudong 00 China MP Filtri U.S.A. Inc. 055 Quaker Pointe PA 895 Drive Quakertown MP Filtri India Pvt. Ltd. Plot-7F, Raj Pinnacle, Beside RMZ Centennial Brookefield Road, Whitefield Bangalore PASSION TO PERFORM mpfiltri.com CMPAEN006A Rev
High Pressure fi lters. FHP series. Maximum pressure up to 420 bar - Flow rate up to 750 l/min. High Pressure fi lters
igh Pressure fi lters FP series Maximum pressure up to bar Flow rate up to 7 l/min igh Pressure fi lters FILTER SIZING The correct filter sizing have to be based on the variable pressure drop depending
More informationFHF325 series. Filter housing according to SAE J2066 for HF4 filter elements. High Pressure fi lters
High Pressure fi lters FHF5 series Maximum pressure up to 50 bar Flow rate up to 500 l/min housing according to SAE J066 for HF filter s 95 High Pressure fi lters FILTER SIZING The correct filter sizing
More informationDIN Filter element according to DIN Low & Medium Pressure filters. Maximum pressure up to 60 bar - Flow rate up to 330 l/min
Low & Medium Pressure filters & series Maximum pressure up to 60 bar Flow rate up to 0 l/min DIN 550 09 Low & Medium Pressure filters FILTER SIZING The correct filter sizing have to be based on the variable
More informationLMP series. 305 Low & Medium Pressure filters MULTIPORT. Maximum pressure up to 80 bar - Flow rate up to 200 l/min
Low & Medium Pressure fi lters LMP - series Maximum pressure up to 8 bar - Flow rate up to l/min 5 Low & Medium Pressure filters FILTER SIZING The correct filter sizing have to be based on the variable
More informationLDP & LDD series Filter element according to DIN Maximum working pressure up to 6 MPa (60 bar) - Flow rate up to 330 l/min
Low & Medium Pressure filters LDP & series Maximum working pressure up to 6 MPa (60 bar) Flow rate up to 0 l/min 7 Low & Medium Pressure filters Introduction FILTER SIZING INDEX CALCULATION CORRECTIVE
More informationLMP series
Low & Medium Pressure fi lters LMP 95-95-95 series Maximum working pressure up to.5 MPa (5 bar) - Flow rate up to 000 l/min 7 Low & Medium Pressure filters Introduction FILTER SIZG DEX CALCULATION CORRECTIVE
More informationReturn / Suction fi lters In-line. LMP 124 series MULTIPORT. Maximum pressure up to 80 bar - Flow rate up to 200 l/min. Return / Suction fi lters
Return / Suction fi lters Inline LMP series Maximum pressure up to 8 bar Flow rate up to l/min 9 Return / Suction fi lters FILTER SIZING The correct filter sizing have to be based on the variable pressure
More informationSERIES. Maximum pressure 110 bar
SERIES Maximum pressure 0 bar F l o w r a t e s t o 9 5 l / m i n Technical data FMP 09 Compatibility Filter housing (Materials) Head: nodized aluminium Housing: nodized aluminium Bypass valve: Steel Pressure
More informationReturn fi lters. FRI series. Maximum pressure up to 20 bar - Flow rate up to 1500 l/min. Return fi lters
Return fi lters series Maximum pressure up to bar - Flow rate up to 15 l/min 193 Return fi lters GENERAL INFORMATION Technical data Return filter Maximum pressure up to bar - Flow rate up to 15 l/min Filter
More information525 Stainless steel high pressure filters. FZP series. Maximum pressure up to 420 bar. Stainless steel high pressure fi lters
Stainless steel high pressure fi lters FZP series Maximum pressure up to 0 bar 55 Stainless steel high pressure filters FILTER SIZING The correct filter sizing have to be based on the variable pressure
More informationSERIES FRI. Maximum working pressure 20 bar Flow rate to 1200 l/min. s.p.a
New Headquarters : MP FILTRI S.p.. Italy Via 1 Maggio, n. 3 Pessano con Bornago (Milano) Italy Tel. +39./973.1 Fax +39./9741497-974188 email: sales@mpfiltri.com http://www.mpfiltri.com GRT BRITIN MP FILTRI
More informationReturn / Suction fi lters Tank mounted. MRSX series. Maximum pressure up to 10 bar - Flow rate up to 300 l/min. Return / Suction fi lters
Return / Suction fi lters mounted MRSX series Maximum pressure up to bar Flow rate up to l/min 9 Return / Suction fi lters FILTER SIZG The correct filter sizing have to be based on the variable pressure
More informationFMP IN-LINE FILTER SERIES. Maximum working pressure 250 bar. Flow rate to 500 l/min
INLIN FILTR Maximum working pressure 0 bar Flow rate to 00 l/min R.F. Filter Symbol without bypass Filter Symbol with Reverse Flow R.F. Filter Symbol with bypass Filter Symbol with bypass & Reverse Flow
More informationFlow rates to 500 l/min
FF 5 Filter housing in according to SE J066 for F filter elements Maximum pressure 50 bar Flow rates to 500 l/min Technical data Filter housing (Materials) ead: Cast iron (chemical heat treatment) ousing:
More informationA complete line of pressure differential visual and electrical indicators are available with this series of filters.
D e s c r i p t i o n FHP series filters are designed for high pressure line applications and are suitable for in-line installation. Continued research and development on both the filter bodies and the
More informationSERIES SF2-250 SUCTION FILTER. Flow rate to 45 gpm
SERIES SF2-250 SUCTION FILTER Flow rate to 45 gpm D e s c r i p t i o n 250 The SF2 series suction filter are designed for reservoir side-wall applications. This completely new design of filter allows
More informationOUT. The SF2 series suction filter are designed for reservoir side-wall applications. This completely new design of filter allows the filter
D e s c r i p t i o n 250 The SF2 series suction filter are designed for reservoir side-wall applications. This completely new design of filter allows the filter within the filter preventing oil loss from
More informationFMM bar. Working pressure. Style T. Style D. Style S. Style B D.I. D.I. D.I. D.I.
30 FMM 050 SRIS FMM 050 Working pressure 0 bar Style S Style Style T Style D 3 3 Technical data Filter body (Materials) Head: Cast iron (chemical heat treatment) Housing: Steel (chemical heat treatment)
More informationMPF filters within this range are suitable for flow rates up to 750 l/min.
D e s c r i p t i o n MPF series filters are designed for return lines, and are installed semi-immersed in a reservoir. Continued Research & Development on both the filter bodies and the filter elements
More informationRF2 Maximum pressure 20 bar F l o w r a t e s t o l / m i n
RF2 96 Maximum pressure 20 bar F l o w r a t e s t o 4 5 5 l / m i n Filter housing (Materials) Filter body: luminium over: Nylon Valve: Nylon - Steel nti-emptying valve: Steel Pressure Working pressure:
More informationWorking pressure. 350 bar. Style B Series FHD 051. Series FHD 325/332 D.I. D.I. D.I. A A
98 FD SRIS FD Working pressure 350 bar Style S Style Series FD 05 Style Series FD 35/33 D.I. D.I. D.I. 99 Technical data body (Materials) ead: Cast iron (chemical heat treatment) ousing: Steel (chemical
More informationSERIES SF2-500 SUCTION FILTER. Flow rates to 225 gpm
SERIES SF2-5 SUTION FILTER Flow rates to 225 gpm D e s c r i p t i o n 5 The SF2 series are designed for reservoir side-wall mounting applications, suitable for flow rates to 225 gpm and filtration from
More informationA complete line of pressure differential visual and electrical indicators are available with this series of filters.
D e s c r i p t i o n FHB series filters are designed for pressure line applications where manifold mounting is a specific requirement. The manifold type filters are designed to integrate onto manifold
More informationFHA 051 Working pressure 6000 psi
6 SRIS Working pressure 6000 psi Style S Style Style T Style D Style V Style Z D.I. 7 8 Technical data Filter body (Materials) Head: Steel (chemical heat treatment) Housing: Steel (chemical heat treatment)
More informationFlow rates to 3000 l/min
MPH Maximum pressure bar Flow rates to l/min echnical data housing (Materials) Head: luminium: MPH nodised luminium: MPH 68 Painted luminium: MPH 66 Cover: Nylon: MPH luminium: MPH nodised luminium: MPH
More informationPOWER TRANSMISSION PRODUCTS ACCESSORIES
POWER TRANSMISSION PRODUCTS ACCESSORIES PASSION TO PERFORM A WORLDWIDE LEADER IN THE FIELD OF HYDRAULIC FILTRATION EQUIPMENT. Our company started life in 1964, when Bruno Pasotto decided to attempt to
More informationMPS/MST SERIES SPIN - ON FILTER SUCTION - RETURN. Maximum working pressure 12 bar. Flow rates to 300 l/min
MPS/MST SERIES SPIN - ON FILTER SUCTION - RETURN Maximum working pressure 12 bar Flow rates to 3 l/min D e s c r i p t i o n MPS/MST The spin-on filter series is a complete product range suitable, for
More informationD e s c r i p t i o n
e s c r i p t i o n MPH and MPI series filters are designed for returnline applications and provide various installation applications. The filters are installed semiimmersed (MPH) or totally immersed into
More informationMPH Maximum pressure 10 bar F l o w r a t e s t o l / m i n
MPH Maximum pressure bar F l o w r a t e s t o l / m i n 6 echnical data housing (Materials) Head: luminium: MPH ---- nodised luminium: MPH 6-8 Painted luminium: MPH 66 Cover: Nylon: MPH --- luminium:
More informationMPH Maximum pressure 10 bar F l o w r a t e s t o l / m i n
MPH Maximum pressure bar F l o w r a t e s t o l / m i n 6 echnical data Filter housing (Materials) Head: luminium: MPH ---- nodised luminium: MPH 6-8 Painted luminium: MPH 66 Cover: Nylon: MPH --- luminium:
More informationHydraulic Filtration. Product Range. Low & Medium Pressure Filters. Return Filters MPFX MPTX MFBX. China United Kingdom India Canada
M Y (Not LMP900-901/902-903/950-951/952-953-954) Positioned on the return line to the tank, return filters perform the task of filtering fluid and preventing particles entering the system - externally
More informationOil Solutions. RIF 300 Return Line Filters. Local solutions for individual customers worldwide FILTRATION TECHNOLOGY
Oil Solutions FILTRATION TECHNOLOGY RIF 3 Return Line Filters Local solutions for individual customers worldwide www.oilsolutions.com.au sales@oilsolutions.com.au Distributor Walter Stauffenberg GmbH &
More informationD e s c r i p t i o n
D e s c r i p t i o n 250 The SF2 series suction filter are designed for reservoir side-wall applications. This completely new design of filter allows the filter within the filter preventing oil loss from
More informationSPIN-ON FILTER - LOW PRESSURE LINE
SERIES MSH SPIN-ON FILTER - LOW PRESSURE LINE Maximum working pressure 5 psi Flow rate to 8 GPM D e s c r i p t i o n MSH working pressure of 5 psi, with a peak pressure This filter MSH series utilises
More informationSTAUFF STAUFF. Local solutions for individual customers worldwide. Medium Pressure Filters SMPF FILTRATION TECHNOLOGY
STAUFF THIS IS STAUFF RESPONSE AND FLEXIBILITY COMPETENT SERVICE PROMPT DELIVERY ENSURED QUALITY FRIENDLY SERVICE PROVEN IN PRACTICE Australia Stauff Corporation (Pty.) Ltd. P.O.Box 227, 24-26 Doyle Avenue,
More informationInline Filter MFM. Flow rates up to 100 l/min Pressure range up to 280 bar Material: EN-GJS / steel E /01.04
Inline Filter MFM Flow rates up to 100 l/min Pressure range up to 280 bar Material: EN-GJS 400-15 / steel 1. TECHNICAL SPECIFICATIONS 1.1. FILTER HOUSING Construction The inline filter consists of a filter
More informationReturn Line Filter HF4R up to 450 l/min, up to 10 bar
Return Line Filter HF4R up to 450 l/min, up to 10 bar 9" 18" 27" 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed in accordance with international regulations.
More informationSTAUFF. Local solutions for individual customers worldwide. Medium Pressure Filters MF-MQ. Operating Pressure: max 280 bar (4.
STAUFF F I LT R AT I O N T E C H N O L O G Y Medium Pressure Filters MFMQ Operating Pressure: max 280 bar (4.000 PSI) Local solutions for individual customers worldwide STAUFF Filtration Technology MediumPressure
More informationSRK-COMBO. Return & Suction Filters Low Pressure Filter In-Tank up to 10 bar. Filter Elements Emergency Suction
Return & Suction Filters Low Pressure Filter In-Tank up to 10 bar Technical Data Filter Elements Main Operating pressure up to 1000 kpa (10 bar). Static pressure testing up to 1500 kpa (15 bar). Back pressure
More informationPressure: Max working 280 bar (4000 psi) (acc. to NFPA T ) Burst 840 bar (12200 psi) (acc. to NFPA T )
HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working 280 bar (4000 psi) (acc. to NFPA T 3.10.5.1) Burst 840 bar (12200 psi) (acc. to NFPA T 3.10.5.1) Housing
More informationSTAUFF STAUFF. Local solutions for individual customers worldwide. Return Line Filters RTF FILTRATION TECHNOLOGY. Ordering Code # :SFT A - UK
STAUFF THIS IS STAUFF RESPONSE AND FLEXIBILITY COMPETENT SERVICE PROMPT DELIVERY ENSURED QUALITY FRIENDLY SERVICE PROVEN IN PRACTICE Australia Stauff Corporation (Pty.) Ltd. P.O.Box 227, Unanderra Wollongong,
More informationReturn Line Filter RF
HYDAC return line filters type RF are designed to be mounted directly on tank tops. Inline mounting is also possible. Return Line Filter RF Flow rates up to 5, l/min Pressure range up to 25 bar Material:
More informationFiltrec elements are tested according to ISO 2941, ISO 2942 and ISO 23181
Common HYDRAULIC FILTRATION Side wall mounting suction filters Technical Information Connection Ports: 1-1 1/4-1 1/2 BSP (other thread options on request) 1 1/2 SAE J518-3000/M12 Housing Materials: Cover:
More informationConnection Ports: 3/4 1 1/4 BSP (other thread options on request)
HYDRAULIC FILTRATION Medium pressure, in line spin-on filters Technical Information Pressure: Max working (acc. to NFPA T 3.10.17): FA-4-1x: 34,5 bar (500 psi) FA-4-21: 24 bar (348 psi) Burst (acc. to
More informationMPT SERIES RETURN FILTER
MPT SRIS The series of filters MPT has specifically been designed for use on mobile power packs for industrial, mobil and lift truk applications. The MPT filter range is suitable for flow rates up to 50
More informationInline Filter RFL. Cast version Volume rates up to 1300 l/min* Pressure range 25/40 bar
RFL inline filters are designed for inline mounting in hydraulic and lubrication systems. Inline Filter RFL Cast version Volume rates up to 1300 l/min* Pressure range 25/40 bar * For larger flow rates,
More informationPressure Filter for Manifold Mounting DFP and for Reversible Flow DFPF
Pressure Filter for Manifold Mounting DFP and for Reversible Flow DFPF up to 600 l/min, up to 315 bar 60 110 140 160 240 280 330 500 660 1.X 660 2.X 990 1320 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING
More informationSuction Filter SF/SFM/SFF and Suction Filter Elements S/S..
Suction Filter /M/F and Suction Filter Elements S/S.. up to 500 l/min Filters: 60 110 160 240 330 M 330 F 400 F 500 Elements: S SH. SU. SG. 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The
More informationHD 790 HD 990 In-line mounting Operating pressure up to 630 bar / 9137 psi Nominal flow rate up to l/min / gpm
High Pressure Filters Worldline 4 HD 79 HD 99 In-line mounting Operating pressure up to bar / 97 psi Nominal flow rate up to. l/min / 4. gpm Description Application In the high pressure circuits of hydraulic
More informationPressure: Max working F280 D12x port size 1/2 & 3/4 : 420 bar (6000 psi) Burst F280 D12x port size 1/2 & 3/4 : 1260 bar (18000 psi)
HYDRAULIC FILTRATION F8-D1 series In line medium pressure filters Technical Information Housing Pressure: Max working F8 D1x port size 1/ & 3/4 : 4 bar (6 psi) F8 D1x port size 1 : 3 bar (4 psi) F8 D14x:
More informationConnection Ports: 3/4 1 1/4 BSP (other thread options on request) aluminium alloy NBR (FKM on request)
HYDRAULIC FILTRATION F4-DMD series In line medium pressure filters Technical Information Pressure: Max working (acc. to NFPA T 3.1..1): F4-DMD/8/11: 7 bar (11 psi) F4-DMD1/3/4: 4 bar (8 psi) Housing Burst
More informationBy-pass: 1,7 bar (24.6 psi) setting N.B. Cartridge with integrated bypass valve and antidrainback membrane
HYDRAULIC FILTRATION Spin-on, tank top return filters Technical Information Pressure: Max working 12 bar (175 psi) (acc. to NFPA T 3.10.17) Burst 20 bar (290 psi) (acc. to NFPA T 3.10.17) Connection Ports:
More informationReplacement cartridge filter
Replacement cartridge filter RE 426/0. /2 Type 7 SL 0 to 260; 7 SLS 90 to 260; SL 0 to 80 D Size 7 SL: 0 to 260 7 SLS: 90 to 260 SL: 0 to 80 D Nominal pressure 7 and/or bar Port up to G /4, SAE /2 (000
More informationConnection Ports: 1/2 1 1/2 BSP (other thread options on request) aluminium alloy NBR (FKM on request)
HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working (acc. to NFPA T 3.1.5.1): F1-XD4/63/1: 1 bar (15 psi) F1-XD16/25/4: 8 bar (12 psi) Housing Burst (acc. to
More informationPressure: Max working 8 bar (116 psi) (acc. to NFPA T ) Burst 16 bar (232 psi) (acc. to NFPA T )
HYDRAULIC FILTRATION Tank top return filters Technical Information Pressure: Max working 8 bar (116 psi) (acc. to NFPA T 3.1..1) Burst 16 bar (232 psi) (acc. to NFPA T 3.1..1) Housing Connection Ports:
More informationPressure: Max working 110 bar (1600 psi) (acc. to NFPA T ) Burst 330 bar (4800 psi) (acc. to NFPA T ) Wire mesh µm
HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working 110 bar (1600 psi) (acc. to NFPA T 3.10.5.1) Burst 330 bar (4800 psi) (acc. to NFPA T 3.10.5.1) Housing
More informationChange-Over Pressure Filter DFDK
Change-Over Pressure Filter up to 2500 l/min, up to 315 bar 30 60 110 140 160 240 280 330 500 660 1.x 660 2.x 990 2.x 1320 2.x 1320 3.x 2640 3.x 3960 3.x 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING
More informationHD 790 HD 990 In-line mounting Operating pressure up to 630 bar Nominal flow rate up to l/min
High Pressure Filters Worldline HD 79 HD 99 In-line mounting Operating pressure up to bar Nominal flow rate up to. l/min Description Application In the high pressure circuits of hydraulic systems. Performance
More informationOil Solutions. Tank Top Return Filters RTF. Local solutions for individual customers worldwide FILTRATION TECHNOLOGY
Oil Solutions FILTRATION TECHNOLOGY Tank Top Return Filters RTF Local solutions for individual customers worldwide www.oilsolutions.com.au sales@oilsolutions.com.au Distributor Walter Stauffenberg GmbH
More informationTank top return-line filter Pi 5000
MAHLE Industrialfiltration is now Filtration Group. For more information, visit www.filtrationgroup.com Tank top return-line filter Pi 5000 Nominal size 160 up to 1000 according to DIN 24550 1. Features
More informationPressure Filter DF...K P, DF...M P, Flange Mounted
Pressure Filter, DF...M P, Flange Mounted up to 550 l/min, up to 260 bar DF...M P 330...1.X 160 240 280 500...1.X 660...1.X 660...2.X 990...2.X 1320...2.X 660...3.X 990...3.X 1320...3.X 1. TECHNICAL SPECIFICATIONS
More informationTHE IMPORTANCE OF AN EFFICIENT FILTRATION
In line high pressure filters HF 745 / HF 748 series THE IMPORTANCE OF AN EFFICIENT FILTRATION The main cause of anomalies in hydraulic systems has to be attributed to the presence of contaminants in the
More informationHIGH PRESSURE FILTERS
APPLICATION HIGH PRESSURE FILTERS For Manifold Block Mounting Series DF...P Pressures to 45 psi Flows to 18 gpm HYDAC DF...P High Pressure Filters are designed to be mounted directly onto the manifold
More informationSPIN-ON FILTERS & ELEMENTS
ABSOLUTE RATED (BETA SPIN ) & NOMINAL RATED SPIN-ON FILTERS & ELEMENTS Single and Twin Element Models Pressures to 20 psi Flows to 120 gpm APPLICATION HYDAC Spin-On Filters are for filtration of hydraulic
More informationInline Filter RFLD. Change-Over. Cast Version Flow Rates up to 1300 l/min* Pressure Range 25/40/64 bar With Ball Change-Over Valve E /01.
Change-Over Inline Filter RFLD Cast Version Flow Rates up to 3 l/min* Pressure Range 25/4/64 bar With Ball Change-Over Valve * For higher flow rates, please refer to brochure RFLD Welded Version E 7.9.2/.4
More informationHigh Pressure Filters HD 044 HD 064. Flangeable Operating pressure up to 500 bar Nominal flow rate up to 105 l/min e
High Pressure Filters HD HD Flangeable Operating pressure up to bar Nominal flow rate up to l/min.3-e Description Application In the high pressure circuits of hydraulic systems. Performance features Protection
More informationSuction Filter SF/SFM/SFF and Suction Filter Elements S and S..
Suction Filter /M/F and Suction Filter Elements S and S.. up to 500 l/min Filters: 60 100 160 240 330 M 330 F 400 F 500 Elements: S SH. SU. SG. 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationPOWER TRANSMISSION PRODUCTS COUPLINGS
POWER TRANSMISSION PRODUCTS COUPLINGS PASSION TO PERFORM A WORLDWIDE LEADER IN THE FIELD OF HYDRAULIC FILTRATION EQUIPMENT. Our company started life in 1964, when Bruno Pasotto decided to attempt to cater
More informationInline Filters NF. Flow rates up to 3,500 l/min Pressure range 25 bar Material: Aluminium / Aluminium-Cast Iron
NF filters are designed for inline mounting and as tank-top mounted return line filters. These filters can also be used on filling, flushing and off-line units. Inline Filters NF Flow rates up to 3,500
More informationMobile Filtration Systems SMFS-P and SMFS-U
SMFS-P-015 SMFS-U-030 SMFS-U-DL-015-G SMFS-U-060 SMFS-U-110 SMFS-U-CM-110 Mobile Filtration Systems SMFS-P and SMFS-U Introduction 2 Introduction STAUFF Filtration Technology offers a complete range of
More informationPressure: Max working 8 bar (116 psi) (acc. to NFPA T ) Burst 16 bar (232 psi) (acc. to NFPA T ) Buna-N (FKM on request)
HYDRAULIC FILTRATION Return filters, tank top mounting, inside-to-outside filtration Technical Information Pressure: Max working 8 bar (116 psi) (acc. to NFPA T 3.10.5.1) Burst 16 bar (232 psi) (acc. to
More informationSuction Filter Pi 200
Suction Filter Pi 0 Nominal size up to 90 1. Features High performance filters for modern hydraulic systems Provided for pipe installation Modular system Compact design Minimal pressure drop through optimal
More informationLS 025 LS 035 In-line mounting Connection up to G¾ / -12 SAE Nominal flow rate up to 33 l/min / 8.7 gpm
Suction Filters LS 025 LS 035 In-line mounting Connection up to G¾ / -2 SAE Nominal flow rate up to 33 l/min / 8.7 gpm Description Application To be installed in the suction line of the pumps of hydraulic
More informationPRESSURE FILTERS. BYPASS VALVE Setting: 170 kpa (1,7 bar) ± 10% WORKING TEMPERATURE From -25 to +110 C
COMPONENTS MATERIALS Head: Aluminium alloy Spinon cartridge: Steel Bypass valve: Polyammide Seals: NBR Nitrile (FKM on request fluoroelastomer) Indicator housing: Brass APPLICATION EXAMPLE PRESSURE (ISO
More informationReturn Line Filter RF
Return Line Filter up to 15000 l/min, up to 25 bar 30 60 110 160 240 330 450 580 660 950 1300 2500 4000 5200 6500-7800 15000 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings
More informationInline Filter LPF D A Flange-Mounted up to 280 l/min, up to 25 bar
Inline Filter LPF D A Flange-Mounted up to 280 l/min, up to 25 bar 160 240 260 280 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed in accordance with international
More informationRETURN FILTERS. MATERIALS Head: Aluminium alloy Cover & bowl: Polyammide Bypass valve: Polyammide Seals: NBR Nitrile Indicator housing: Brass
COMPONENTS RB MATERIALS Head: Aluminium alloy Cover & bowl: Polyammide Bypass valve: Polyammide Seals: NBR Nitrile Indicator housing: Brass APPLICATION EXAMPLE PRESSURE (ISO 10771-1:2) Max working: 0 kpa
More informationSeries TSW Sheet No J. SUCTION FILTER, horizontal tank mounted. Dimensions: mounting surface
SUCTION FILTER, horizontal tank mounted Sheet No. 1905 J Series TSW 210-310 Dimensions: type TSW 210 TSW 310 connection - 20 SAE -20 SAE A 12.09 15.47 B 11.57 14.96 C 11.42 14.76 D 8.62 12.00 E.26.30 weight
More informationLow Pressure Filters
MF, MFD, MFDS Series Spin-On Filters 250 PSI up to 120 GPM Hydraulic Symbol /80/85/160/180 MF 90/95/190/195 A A B B Features MF Filters are manufactured with an aluminum head. Choice of NPT, SAE straight
More informationPressure Filters DF...M A / DF...Q E DF...MHA / DF...MHE Flow rates up to 500 l/min Pressure range up to 315 bar Material: SG Iron/ADI, Steel
Manifold Mounted, Rear Flanged Pressure Filters DF...M A / DF...Q E DF...MHA / DF...MHE Flow rates up to 5 l/min Pressure range up to 35 bar Material: SG Iron/ADI, Steel . DESCRIPTION.. FILTER HOUSING
More informationReturn Line Filter RFM with 4-Hole Mounting
Return Line Filter with 4-Hole Mounting Tank-top mounted versions: up to 850 l/min, up to 10 bar 75 90 150 165 185 210 270 330 500 600 661 851 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationHIGH PRESSURE FILTERS
HIGH PRESSURE FILTERS Series DF & LF Pressures to 6 PSI Flows to 18 GPM APPLICATION HYDAC DF & LF In-line High Pressure Filters are designed for use on hydraulic power units, machine tools, plastics machinery,
More informationPRESSURE FILTER Series HPV DN 25 PN 420
PRESSURE FILTER Series HPV 60-150 DN 25 PN 420 Sheet No. 1478 E 1. Type index: 1.1. Complete filter: (ordering example) HPV. 90. 10VG. HR. E. P. -. G. 5. -. D2. AE 1 2 3 4 5 6 7 8 9 10 11 12 HPV = pressure
More informationQuality and Service worldwide. Hydraulic Accessories Flow Indicators
Quality and Service worldwide Hydraulic Accessories Flow Indicators Distributor Walter Stauffenberg GmbH & Co. KG P.O.Box 1745 D-58777 Werdohl Im Ehrenfeld 4 D-58791 Werdohl Tel. : + 49 (0) 2392 916-0
More informationInline filter with filter element according to DIN 24550
Inline filter with filter element according to DIN 24550 RE 51422/07.11 Replaces: 12.10 1/18 Type 350LEN0040 to 1000; 350LE0130, 0150 Size according to DIN 24550: 0040 to 1000 Additional sizes: 0130, 0150
More informationES 074 ES 094 Tank top mounting Connection up G1¼ Nominal flow rate up to 80 l/min
Suction Filters ES 074 ES 094 Tank top mounting Connection up G1¼ Nominal flow rate up to 80 l/min Description Application To be installed in the suction line of the pumps of hydraulic systems resp. upstream
More informationPressure Filter DF Pressure Filter for Reversible Oil Flow DFF/DFFX
Pressure Filter DF Pressure Filter for Reversible Oil Flow DFF/DFFX up to 2000 l/min, up to 420 bar DF/DFF...1.X/2.X 30 60 110 140 160 240 280 330 500 660 990 1320 1500 2000 3000 4000 DF...3.X DFFX...1.X/2.X
More informationHigh Pressure Filters SF
FILTRTION TECHNOLOGY High Pressure Filters SF Quality and Service worldwide ustralia: Stauff Corporation (Pty.) Ltd. P.O. ox 227 24-26 Doyle venue, Unanderra Wollongong, N.S.W. US-2526 Unanderra Tel.:
More informationPiston Pumps Series P2 / P3 Variable Displacement
Piston Pumps Series P2 / P3 Variable Displacement Catalogue HY11-2600/UK July 2003 Contents Series P2/P3 Description Technical information 3 Ordering code 4 Control options LA and LB 6 Control options
More informationTank top return-line filter Pi 5000
MAHLE Industrialfiltration is now Filtration Group. For more information, visit www.filtrationgroup.com Tank top return-line filter Pi 5000 Nominal size 160 up to 00 according to DIN 24550 1. Features
More informationDuplex Pressure Filters
Duplex Pressure Filters Series DFDK Ball Valve Selector Pressures to 45 psi Flows to 9 gpm APPLICATIONS HYDAC DFDK Duplex Filters are ideal for use on hydraulic test equipment, robots, or other critical
More informationChange-Over Inline Filter RFLD Welded Version
Change-Over Inline Filter RFLD Welded Version up to 15000 l/min, up to 16 bar RFLD 1300 CAS to RFLD 15000 CBW 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed
More informationOff-line Filters FNS 060. With flow control valve Operating pressure up to 320 bar Nominal flow rate up to 4 l/min e
Off-line Filters FNS 060 With flow control valve Operating pressure up to 320 bar Nominal flow rate up to 4 l/min 80.20-2e Description Application In the high pressure circuits of hydraulic and lubricating
More informationInline filter with filter element according to DIN 24550
Inline filter with filter element according to DIN 24550 RE 51421/07.11 Replaces: 12.10 1/16 Type 245LEN0040 to 400; 245LE0130, 0150 Size according to DIN 24550: 0040 to 0400 Additional sizes: 0130, 0150
More informationRETURN FILTERS. MATERIALS Head: Aluminium alloy Spin-on cartridge: Steel Bypass valve: Polyammide Seals: NBR Nitrile Indicator housing: Brass
COMPONENTS RC MATERIALS Head: Aluminium alloy Spin-on cartridge: Steel Bypass valve: Polyammide Seals: NBR Nitrile Indicator housing: Brass APPLICATION EXAMPLE PRESSURE (ISO 10771-1:2002) Max working:
More informationFPG-MDS PRESSURE FILTERS MATERIALS PRESSURE BYPASS VALVE WORKING TEMPERATURE COMPATIBILITY (ISO 2943) HYDRAULIC DIAGRAM.
MATERIALS Head: Aluminium alloy Bowl: Steel Bypass valve: Steel Seals: NBR Nitrile (FKM - on request fluoroelastomer) Indicator housing: Brass PRESSURE Max working: 5 MPa ( bar) Collapse, differential
More informationTank top return-line filter Pi 5000
Tank top return-line filter Pi 5000 Nominal size 40 up to 100 according to DIN 24550 1 Features High performance filters for modern hydraulic system Provided for tank top installation Modular system Compact
More informationIn-Line Filters. Section Index. High FPK
Hydraulic In-Line Filters Section Index NEW Medium Pressure Filters FMK-FM............................ FCK-LC............................. 123 HMK04 Duramax.................... 124 HMK05 Duramax....................
More informationBlock mounting filter, lateral flange-mounting possible
Block mounting filter, lateral flange-mounting possible RE 0/.0 Replaces: 0.09 / Types 0/0 FEN 000 to 000; 0/0 FE 000, 00, 008 Nominal sizes according to DIN 0: 000 to 000 Nominal sizes according to BRFS:
More informationCourtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800)
Features MF Filters are manufactured with an aluminum head. MF, MFD, MFDS Series Spin-On Filters Choice of NPT, SAE straight thread O-ring boss, BSPP, and SAE 4-bolt flange porting to allow easy installation
More information