Tools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool

Size: px

Start display at page:

Download "Tools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool"

Winfred Chase
5 years ago
Views:

1 INSTALL INSTRUCTIONS C-VS-1500-TAH Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (9 inches wide) 15 inches of Equipment mounting space Note: 2 inches of mounting space is for the supplied Aux panel. Console only includes an additional 13 inches of customer specified equipment brackets and filler panels. Tools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool Parts and Mounting Hardware: 1 Main console housing CM CM Sub Assembly 2 Floor bracket CM /2 Aluminum spacer for floor bracket (rear) CM /4 Aluminum spacer for floor bracket (front) CM Driver side trim panel CM Passenger side trim panel CM Electrical accessory mounting plate CM Rear mounting plate CM inch panel for OEM 12 volt socket and Aux module C-EB20-USD1-1P 2 7/8 hole plug (included with C-EB20-USD1-1P) CM Dome plug for rear mounting plate GSM #8 x 3/8 Torx head sheet metal screws CM /4 serrated nut GSM /4 Flat washer GSM /4 x 3/4 Carriage bolt GSM /4 x 3/4 Hex bolt GSM /8 Flat washer GSM mm x 45mm Hex bolts (if floor is already threaded) GSM /8 x 1.75 Hex bolt (if floor mount location is not threaded) GSM33303 ALWAYS! Read all instructions before installing any Havis, Inc products. Use hardware provided with install kit

C-VS-1500-TAH-1 (Assembly) Electrical Accessory mounting plate Between trim

C-EB20-USD1-1P For OEM 12 volt socket and Aux module.

Order 12 volts socket kit C-HK-181 separately (if desired) CM006831 Rear

Floor bracket (one each side) IMPORTANT NOTE: Install CM006193 floor brackets

Between bracket and hump, use 1/2 spacers at rear and 3/4 spacers at front.

75 self threading bolts and 3/8 flat washers and spacers RE: Retail Tahoe or

or seat and use 10mm x 45mm bolts and 3/8 flat washers and spacers Photos

2 C-VS-1500-TAH-1 (Assembly) Electrical Accessory mounting plate Between trim panels CM CM Passenger side trim panel 2 inch panel # C-EB20-USD1-1P For OEM 12 volt socket and Aux module. Also has two (2) 7/8 holes for optional 12 volts sockets. Order 12 volts socket kit C-HK-181 separately (if desired) CM Rear mounting plate CM Driver side trim panel Main Console Housing CM Floor bracket (one each side) IMPORTANT NOTE: Install CM floor brackets to existing OEM mount points as follows. Between bracket and hump, use 1/2 spacers at rear and 3/4 spacers at front. RE: Police Pursuit Vehicle without center seat or OEM console Use 3/8 x 1.75 self threading bolts and 3/8 flat washers and spacers RE: Retail Tahoe or PPV (code A95) with OEM center console or PPV with center seat Remove console or seat and use 10mm x 45mm bolts and 3/8 flat washers and spacers Photos currently do not show the new speaker vents in the side trim panels. It is up to the installer to determine if a speaker or other device can be mounted behind these vents for their specific application.

View of 2015 Tahoe transmission hump between front seats

vehicle had a factory center console or seat installed.

75 self-threading bolts and washers if vehicle does not

Between bracket and hump, use 1/2 spacers at rear and

Place console on the floor brackets and line up to dash

Using the opening in the bottom of the console attach

Rear Mounting Plate (CM006831) behind the console and

3 View of 2015 Tahoe transmission hump between front seats Install CM floor brackets to existing OEM mount points. Use 10mm x 45mm bolts and 3/8 flat washers if the vehicle had a factory center console or seat installed. Use 3/8 x 1.75 self-threading bolts and washers if vehicle does not have the center seat or console. Between bracket and hump, use 1/2 spacers at rear and 3/4 spacers at front. Place console on the floor brackets and line up to dash and the slots in the track. Using the opening in the bottom of the console attach the 1/4" serrated nuts (GSM30023) to the bolts Place the Rear Mounting Plate (CM006831) behind the console and line up with the tabs. Using the 2 hole slip in the 1/4 serrated nuts and attach to the bolts. Loosely attach the electrical accessory mounting plate (CM005915) to the console U bracket with 1/4 x 3/4" Hex bolts and washers. (forward mount tabs face down)

Attach driver side trim panel to console with four (4) #8 x 3/8 Torx

Attach passenger side trim panel the same way as driver side.

trim after metal knockout plate has been removed.

Wire and eight (8) butt connectors for extensions must be supplied by

Once both side trim panels are attached check for final fitment and

4 Attach driver side trim panel to console with four (4) #8 x 3/8 Torx head sheet metal screws. Attach passenger side trim panel the same way as driver side. Note: This photo shows the OEM 120 volt socket mounted in the side trim after metal knockout plate has been removed. OEM wire ties and tape may need to be cut in order to have enough wire to extend to this location. Splicing four (4) wire extensions may also be required. Wire and eight (8) butt connectors for extensions must be supplied by the installer. Once both side trim panels are attached check for final fitment and tighten all hardware Console housing installation complete Install 2 inch panel C-EB20-USD1-1P for OEM 12 volt socket and Aux module (if desired) Console shown with C-CUP-I-A11 cup holder and equipment bracket Console mounted with optional C-ARM-104

5 Optional C-1000 enclosed console provides an additional 10 of mounting space. Installation complete View of C-HDM-204 mounted to the console housing with C-MD-302, PKG-KB- 106, and DS-GTC-201. View of C-HDM-204 mounted to the outside of console housing with C-MD-302, PKG-KB- 106, and DS-GTC-201. DMM 130 installed with CM and PKG- KB-106. Also works with C-DMM-135. Double check all mounting and equipment functions.

Tools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool

INSTALL INSTRUCTIONS C-VS-1013-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (9 inches wide) 23 inches of Equipment mounting space Tools Required: Phillips Screw Driver