INSTALLATION INSTRUCTIONS C DMM Nissan Frontier SWING OUT DASH MONITOR MOUNT

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS C DMM Nissan Frontier SWING OUT DASH MONITOR MOUNT"

Cathleen Parks
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS C DMM Nissan Frontier SWING OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system may require two or three main parts that are Sold Separately. See web site Monitor Configurator for more detailed bracket information. 1 Vehicle Specific dash mount bracket. (C DMM 134) 1 Computer Specific Monitor adaptor bracket. (C MM 200 series) 1 Offset adaptor bracket. (C MM 301) The C MM 301 offset adaptor goes between the C DMM 134 and C MM 2XX. It may not be required in some applications. Tablet docking stations with Vesa 75 hole pattern can be bolted directly to C DMM without adaptor. Offset adaptor C MM 303 is available if additional positioning options are desired for docking station. TOOLS REQUIRED: (some tools are not needed for all vehicle installations) Socket set metric & standard Phillips screwdriver Trim removal tools File or plastic cutting tool HARDWARE and PARTS: QTY: DESCRIPTION: PART #: 1 Driver side lower mounting bracket CM Passenger side lower mounting bracket CM Forward upper mounting bracket CM Rear upper mounting bracket CM /4" Serrated nut GSM x 1/2 Machine screw GSM #10 Flat washer GSM31003 Note: The swing door utilizes a gas spring to assist in opening the door and to eliminate the possibility of it slamming shut. If additional damping is desired because of heavier equipment, an optional stronger gas spring is available under Part Number CM (sold separately) Always! Read all instructions before installing any Havis, Inc. products. Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes! Use hardware provided with install kit

C-DMM-134 assembly CM008527 Forward upper mounting Small L bracket CM008528 Rearward upper mounting bracket CM008635 Passenger lower mounting bracket CM008634

2 C-DMM-134 assembly CM Forward upper mounting Small L bracket CM Rearward upper mounting bracket CM Passenger lower mounting bracket CM Driver lower mounting bracket C MM 301 Offset Adaptor Note: Rotation adaptor must be removed in order to use C MM 301 C MM 201 Monitor Mount Adaptor (VESA bracket shown)

View of Frontier dash before installation

starting at the front and working along the

Remove the three (3) screws at the top of the

Unplug all harnesses and remove from the

Locate the two (2) screws beneath the vents.

The plastic tabs at the outer part of the

3 View of Frontier dash before installation Gently pry along the upper change tray starting at the front and working along the edges. Remove the three (3) screws at the top of the trim. Pull the dash assembly towards you. Unplug all harnesses and remove from the truck. Locate the two (2) screws beneath the vents. Remove and set aside. The plastic tabs at the outer part of the screws will need to filed down or cut off. Attach the driver side and passenger side standoff brackets using the previously removed screws. Mounting flange goes inboard.

4 View of the removed dash assembly Drill a 5/16 hole centered in the boxed area shown in red. Repeat for the other side. These holes should line up to lower standoff brackets. Reinstall the dash assembly and plug back in all harnesses. Install the rearward mounting bracket by sliding it under the dash panel. You may have to slightly pop the main dash panel to position it properly. Install the forward mounting L bracket using previously removed OEM screws.

5 Place the DMM frame bracket onto the dash and attach with three (3) x 1/2" machine screws Attach lower frame to standoff brackets trough dash panel holes with x 1/2" machine screws. Test to make sure the door opens and closes properly. Mount equipment and run wiring as needed. Installation is now complete. DS GTC 201 shown with C FAM 117, C ADP 112, and KB 101

INSTALLATION INSTRUCTIONS C-DMM FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT

INSTALLATION INSTRUCTIONS C-DMM-123 2013-2018 FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system requires two or three main parts that are sold separately. See