HITCH INSTALLATION INSTRUCTIONS TESLA MODEL 3 PACKAGE: RACK Present MODEL/TRIM: MAKE: YEARS: 2 HOURS TOOLS REQUIRED: PARTS SUPPLIED:
|
|
- Douglas Summers
- 5 years ago
- Views:
Transcription
1 HITCH INSTALLATION INSTRUCTIONS MAKE: TESLA YEARS: 2017 Present MODEL/TRIM: MODEL 3 WEIGHT CAPACITY TRAILER TONGUE N/A LBS. 200 LBS. PACKAGE: RACK INSTALLATION TIME: 2 HOURS DO NOT EXCEED VEHICLE MANUFACTURE S RECOMMENDATIONS NO WELDING, DRILLING OR VISIBLE TRIMMING UNDER VEHICLE TRIMMING NO YES NO HEAT SHIELD GRAVEL GUARD TRIMMING FASCIA PARTS SUPPLIED: TOOLS REQUIRED: Latching Mechanism (2) Bolts 1/2 13x 4 (2) Nylock Nuts 1/2 3/4 Open End Wrench 8mm 10mm 15mm deep well 17mm 3/4 Ratchet (6) M10 Flat Washers (6) Bolts M10 (6)M10 Serrated Flange Nuts Extension Plastic Pry Tools (8) Rubber Washers (2) Factory Reinforcement Beam Brackets Rack Receiver Flashlight Safety Glasses T25 Torx Dremel Tool File Page 1 of 7
2 1. Dislodge both rear side panels to gain access to rear taillights. Remove (1) plastic rivet on driver side of the vehicle. 2. Remove (2) plastic trunk stops by turning counter clock wise. 8mm s 3. Use a socket to remove (2) nuts securing the tail light. (per side) Unplug the wiring harness from the tail light by pushing down on the clips and pulling away from the light. Plastic Pry Tools 4. Slide the tail lights toward the rear of the vehicle. A plastic pry tool can be used, if necessary. 5. Use a socket to remove screw. 10mm Page 2 of 7
3 6. Remove (3) plastic rivets in the rear wheel well. Remove (1) screw with a torx. T25 Torx 7. Use a 90 degree pick to dislodge (2) plastic covers. Remove (7) screws from the gravel guard trim. Remove (1) plastic rivet. 10mm Plastic Pry Tool 8. With a partner starting above the wheel well at the forward most part of the fascia and apply outward pressure moving toward the rear of the vehicle, push down on the plastic clips to release fascia. 9. Unplug sensor plug on passenger side, before removing the fascia completely. A 90 degree pick can be used to open the clip and remove the plug. PLACE THE FASCIA ON A PAD OR BLANKET TO PREVENT DAMAGE OR SCRATCHES. Page 3 of 7
4 10mm Well Extension 10. Remove (5) screws from plastic trim piece to gain access to reinforcement beam base plate. 11. Remove (6) nuts securing the factory reinforcement beam. Remove reinforcement beam and SAVE for reinstallation. Well 12. Remove (8) nuts securing the factory reinforcement beam base plate. Remove reinforcement beam base plate and discard. SAVE the nuts for the hitch installation. Well (8) Rubber Washer 13. Clean the surface area before installing the hitch. Place (8) supplied Rubber washers on the factory studs before installing hitch beam. Secure the (4) inner vehicle studs with saved nuts. Torque to 45 ft. lbs. 45 ft. lbs. 45 ft. lbs. Page 4 of 7
5 3/4 14. Assemble the latching mechanism. Use a 3/4 Open End Wrench torque wrench and an open end 3/4 wrench to tighten the supplied, 1/2 bolts to 90 ft. lbs. Well 15. Use (6) M10 bolts, washers and nuts to secure factory reinforcement wide beam brackets, loosely to the factory reinforce- Slim ment beam. 17mm socket (Make sure the wide part of the factory reinforcement beam is on top) Tab is the top wide Slim 16. Install the factory rein- Well forcement beam with brackets to the hitch beam. Secure the (4) outer vehicle studs with saved nuts. Torque to 45 ft. lbs. Tighten (6) reinforce- ment beam M10 nuts. Torque to 45 ft. lbs. 45 ft lbs Page 5 of 7
6 CUT OUT LOCATION (INSIDE VIEW) SEE CUT OUT TEMPLATE ATTACHED Dremel Tool 16. Cut out location see cut out template attached (page.7). Cut out the fascia with File Dremel tool. Use a file to smooth out the cut. 17. Reinstall the fascia. Complete steps 1 through 10 in reverse order, to complete the installation. Page 6 of 7
7 IF DOWNLOADING FROM WEB SITE PDF FILE IS NOT TO SCALE Page 7 of 7
HITCH INSTALLATION INSTRUCTIONS TOW XC 40 VOLVO MODEL/ TRIM YEARS: 2 1/2 HOURS to Present PARTS & SUPPLIES: TOOLS REQUIRES: INSTALLATION TIME:
HITCH INSTALLATION INSTRUCTIONS MAKE: VOLVO YEARS: 2018 to Present MODEL/ TRIM XC 40 PACKAGE: TOW INSTALLATION TIME: 2 1/2 HOURS WEIGHT CAPACITY TRAILER 3500 LBS. TONGUE 300 LBS. DO NOT EXCEED VEHICLE
More informationVELAR HITCH INSTALLATION INSTRUCTIONS TOW RANGE ROVER MODEL/ TRIM YEARS: WEIGHT CAPACITY to Present PARTS & SUPPLIES: TOOLS REQUIRES:
HITCH INSTALLATION INSTRUCTIONS MAKE: RANGE ROVER YEARS: 2018 to Present MODEL/ TRIM VELAR PACKAGE: TOW WEIGHT CAPACITY TRAILER TONGUE 5300 LBS. 300 LBS. INSTALLATION TIME: 2 HOURS NO YES YES PARTS & SUPPLIES:
More informationINVISIHITCH. Hidden Hitch Receiver for. BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit)
INVISIHITCH Hidden Hitch Receiver for BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit) Capacity: 7,700 lbs. Towed Weight / 600 lbs Tongue Weight* *
More informationINSTALLATION INSTRUCTIONS
11485 YEARS: 2015-CURRENT Safety glasses should be worn at all times while installing this product. INSTALLATION INSTRUCTIONS MODEL: C300 MAKE: MERCEDES STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE
More informationCADILLAC CTS(V) 10/27/2015 PAGE 1 of 2
11901 CADILLAC CTS(V) 10/27/2015 PAGE 1 of 2 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S
More informationBMW X3 UNDERBODY PANEL TRIM DIAGRAM in
13107 10/5/2012 BMW X3 PAGE 1 OF 2 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 3,500 LBS. TRAILER WEIGHT & 350 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH:
More information2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions
2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More information13316 INSTALLATION INSTRUCTIONS
13316 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2011-PRESENT 2016-PRESENT MAKE: BMW MODEL: X3 X4 STYLE: WARNING: NEVER EXCEED YOUR VEHICLE
More information11900 INSTALLATION INSTRUCTIONS
11900 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2016-PRESENT MAKE: CADILLAC / CHEVROLET MODEL: CTS(V) / CAMARO STYLE: SEDAN / COUPE WARNING:
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More information13387 INSTALLATION INSTRUCTIONS
13387 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2018-PRESENT MAKE: BMW MODEL: X3 STYLE: SUV WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More information11436 INSTALLATION INSTRUCTIONS
11436 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2016 - PRESENT MAKE: CHEVROLET MODEL: VOLT STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE
More informationInstallation Instructions
Installation Instructions Application Fits 2012-2016 Tesla Model S X7201 & X7202 2 & 1.25 EcoHitch Stealth 200 lbs Tongue Weight/2,000 lbs Towing Weight Torklift Central 315 Central Ave N Kent, WA 98032
More information11068 INSTALLATION INSTRUCTIONS
11068 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 009-PRESENT MAKE: INFINITI MODEL: G37 & Q60 POWER RETRACTABLE HARD TOP STYLE: CONVERTIBLE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2012 ZDX Publications No. BII 47089 Issue Date SEP 2011 PARTS LIST Tailgate spoiler 2 Brackets 4 Nuts 4 Bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationPLEASE READ THESE INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION
PART NUMBER: L0SSJ000 INSTALLATION INSTRUCTIONS DESCRIPTION: FORESTER TRAILER HITCH PLEASE READ THESE INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION SAFETY PRECAUTION: When installing Trailer Hitch,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27367 HITCH 2005 ODYSSEY Issue Date DEC 2004 NOTE: An optional heavy-duty power steering cooler, ATF cooler and air duct are required
More information(1) License Plate Light (2) License Plate Plugs
PARTS LIST: 1 HD Replacement Bumper 4 12mm x 40mm Hex Bolts 1 Driver/Left Bracket 4 12mm Nylon Lock Nuts 1 Passenger/Right Bracket 8 12mm x 37mm x 3mm Oversize Flat Washers 2 Thin Side Spacers 4 Rubber
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 38133-38406 HITCH 2008 ODYSSEY Issue Date NOV 2007 NOTE: A required heavy-duty power steering cooler, ATF cooler and air duct are required
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 30250 UNDER SPOILER 2006 RSX Issue Date JULY 2005 PARTS LIST Rear under spoiler 5 Stepped bolts 2 Bolts 7 Flange nuts, 6 mm 3 Square
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT (EX-L WITH NAVI) 2008 RIDGELINE AII 36587 Issue Date MAY 2007 PARTS LIST Attachment Kit P/N: 08B21-SJC-102 Template Rear camera
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationMINI COOPER COUNTRYMAN
2/19/2013 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL
More informationPLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION
INSTALLATION INSTRUCTIONS PART NUMBER: L0SXC000 DESCRIPTION: 09 ASCENT TRAILER HITCH PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION SAFETY PRECAUTION: When installing Trailer Hitch,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26033 KIT 2004 ODYSSEY Issue Date JAN 2004 PARTS LIST Trailer Hitch: P/N 08L92-S0X-100 Heavy-Duty P/S Cooler Kit P/N 53765-S0X-305 Heavy-duty
More informationGROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT.
PAGE 1 0F 6 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application CR-V Publications No. AII 32953-34081 Issue Date NOV 2006 PARTS LIST 2 Corner sensor clips Backup Sensor Attachment Kit P/N 08V67-SWA-100A Back-up sensor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08L92-S0X-100 ODYSSEY AII 22049 Issue Date AUG 2000 PARTS LIST Trailer hitch Receiver cover 2 Small wire ties (1 not used) Ball mount
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2012 CROSSTOUR Publications No. AII 46198 Issue Date JULY 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TP6-101 Upper spacer A (5 mm) (Some are not used.)
More information2017 Current Ford Raptor Bump Stop Kit Installation Instructions
2017 Current Ford Raptor Bump Stop Kit Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationSide Rocker Installation Instructions
Side Rocker Installation Instructions Guidelines + Trial fit all parts prior to painting + Do not use the side rockers as an attachment point for tie downs + Every 3-6 months, make sure all fasteners are
More information13102 INSTALLATION INSTRUCTIONS
1310 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 010-PRESENT MAKE: MERCEDES BENZ MODEL: ML350 BlueTEC, GL350 BlueTEC AWD, GL50, & GL550 STYLE:
More informationInstallation Instructions
Installation Instructions Application Fits 2015+ Subaru Legacy X7271 & X7272 2 & 1.25 EcoHitch Stealth LEGACY 2,000 lbs Weight Carrying/200 lbs Tongue Weight Torklift Central 315 Central Ave N Kent, WA
More information11367 INSTALLATION INSTRUCTIONS
11367 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2012-2015 MAKE: BMW MODEL: 2 SERIES EXCLUDING M2 & 3 SERIES SEDAN & WAGON EXCLUDING M STYLE:
More information11522 INSTALLATION INSTRUCTIONS
522 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 207-PRESENT MAKE: MINI COOPER MODEL: COUNTRYMAN STYLE: WAGON WARNING: NEVER EXCEED YOUR VEHICLE
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More information12167 INSTALLATION INSTRUCTIONS
12167 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2017-PRESENT MAKE: LINCOLN MODEL: CONTINENTAL STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08L92-TX4-200 Application 2013 RDX Publications No. BII 13467 Issue Date MAR 2012 PARTS LIST 4 Nuts, Trailer hitch 10 Plain washers, Ball mount 6 Spring washers,
More informationFRAME AND BUMPERS 13-1 FRAME AND BUMPERS TABLE OF CONTENTS
DN FRAME AND BUMPERS 13-1 FRAME AND BUMPERS TABLE OF CONTENTS BUMPERS... 1 FRAME... 5 BUMPERS TABLE OF CONTENTS DESCRIPTION AND OPERATION BUMPERS...1 AND FRONT BUMPER...1 DESCRIPTION AND OPERATION BUMPERS
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Tow Hitch Wire Harness Kit Quest (2011) 999T8 NW000 Installation of this accessory requires installation of
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2013 ACCORD 4-DOOR Publications No. AII 13026 Issue Date AUG 2012 PARTS LIST Aluminum tape Backup Sensors Attachment Kit P/N 08V67-T2A-100A Control unit
More information2015+ Mustang Rear Valance Installation Instructions P/N: (R F953) (R F953BS)
2015+ Mustang Rear Valance Installation Instructions P/N: 421894 (R1315-17F953) 421919 (R1315-17F953BS) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Rear Valance Kit Installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 201 CR-V Publications No. Issue Date PARTS LIST Trailer Hitch Kit P/N 08L92-T0A-100 Hex nut, 12 mm Trailer hitch Hitch pin Hitch pin clip Ball
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2012 ODYSSEY Publications No. AII 46724 Issue Date SEP 2011 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-TK8-100A Right center sensor clip
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-110 2007 CIVIC 2-DOOR All33536-34848 Issue Date FEB 2007 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 CR-V Publications No. AII 44647 Issue Date AUG 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-SWA-101 Trailer Hitch Harness Kit P/N 08L91-SWA-100 Trailer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 28593 2006 RIDGELINE P/N 08F23-SJC-100 Issue Date FEB 2005 PARTS LIST Center front bumper trim (Not used if the vehicle is equipped
More information11333 INSTALLATION INSTRUCTIONS
11333 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2011-PRESENT MAKE: MINI COOPER MODEL: COUNTRYMAN STYLE: SEDAN WARNING: NEVER EXCEED YOUR
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2012 CR-V Publications No. AII 12095 Issue Date DEC 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-T0A-100 Hex nut, 12 mm Trailer hitch Hitch
More information12114 INSTALLATION INSTRUCTIONS
12114 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2012-PRESENT MAKE: LEXUS MODEL: LS 460 STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2014 CR-V Publications No. AII 49959 Issue Date JULY 2013 PARTS LIST Right corner sensor clip (Black) Backup Sensor Attachment Kit P/N 08V67-T0A-100
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0921 APPLICATION 2007-08 E92 335i/xi without stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2014 ODYSSEY Publications No. AII 49544 Issue Date JUNE 2013 PARTS LIST Bumper edge trim Trailer Hitch Kit P/N 08L92-TK8-100 Trailer hitch
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2009 CR-V Publications No. AII 40373 Issue Date AUG 2008 PARTS LIST Plain washer, 12 mm Trailer Hitch Kit P/N 08L92-SWA-100 Trailer hitch 6 Spring
More informationTOYOTA RAV TRAILER WIRE HARNESS Preparation
Preparation Part Number: PU322-42013-UW Kit Contents Item # Qty Description 1 1 Trailer Module Harness 2 1 Trailer 4-Flat Harness 3 1 Trailer Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24
More informationMustang Classic LightBar Instructions
1994-2004 Mustang Classic LightBar Instructions Note: Read installation instructions before starting. Component List: 1 LightBar 4 Poly Plugs 4 LightBar Bolts 4 LightBar Washers 2 LightBar Rivets 2 Light
More information2015 COLORADO 1 /2 LEVELING KITS
92921000 2015 COLORADO 1 /2 LEVELING KITS Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More information13410 INSTALLATION INSTRUCTIONS
13410 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2010-PRESENT MAKE: SUBARU MODEL: OUTBACK (EXCLUDING SPORT) STYLE: WAGON WARNING: NEVER EXCEED
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Fog Lamp Kit Versa Note (SV Only) 999L1 4Z000 - Fog Lamp Kit Item QTY Description Service Part Number
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
Installation Instructions SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal: Release these clips
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationLingenfelter Signature Series Camaro SS Rear Valance
Lingenfelter Signature Series 2010-2012 Camaro SS Rear Valance PN: L850161410 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-0422 fax www.lingenfelter.com
More informationLights TURN SIGNAL/PARKING LIGHT HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT. Maintenance
Check the operation of your car s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car s visibility and the ability to signal your intentions to
More informationClassic Light Bar Mustang
Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket
More informationWATSON RACING S550 MUSTANG DRAG CHUTE & BUMPER KIT
WATSON RACING 2015+ S550 MUSTANG DRAG CHUTE & BUMPER KIT The Watson Racing Drag Race Parchute Bumper and Chute Kit was designed as an upgrade to the 2016 Super Cobra Jet drag cars, and can also be used
More informationCurrent Ford F150 Race Series R Rear Bumper Installation Instructions
2015 - Current Ford F150 Race Series R Rear Bumper Installation Instructions PREPARATION STEPS 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationINSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370
INSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370 USE EXTREME CAUTION WHEN DRILLING ON ANY VEHICLE. MAKE SURE THAT ALL FUEL LINES, BRAKE LINES, ELECTRICAL
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN & HDX GRILLE GUARD APPLICATION: 2015 & UP Ford F-150 PART NUMBER: 40-3835, 45-3830, 57-3830, 57-3835 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1
More informationMM009 6TH GEN CAMARO MOTOR MOUNT KIT
BMR recommends professional installation of this product. A service lift is also recommended for installation of this product. If the vehicle is equipped with an oil cooler, engine coolant is drained during
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WJ2 FULL-WIDTH FRONT BUMPER APPLICATION: 2018 Jeep Wrangler JL PART NUMBER: 59-80105, 59-80115, 59-80125 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationM-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS
M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationRFB MK6 Jetta Fog Light Kit Wiles Rd.Coral Springs, FL
What s Included: Tools Required: (2) Fog Lights (2) Front Grills Wire Harness Headlight Switch Hardware Kit T25 Torx Wire Cutters 10mm Socket and Rachet Headlight Switch Composite Wedge Tool 01 1. Remove
More informationPart Number: Code: YU1 Kit Contents Item # Quantity Reqd. Description 1 1 RH Lamp Assy. 2 1 LH Lamp Assy.
Document # 3263 5/16/05 SCION tc 2005 - TAIL LIGHT ENHANCEMENT Preparation Part Number: 00016-21550 Code: YU1 Kit Contents 1 1 RH Lamp Assy. 2 1 LH Lamp Assy. 3 1 Hardware Bag Hardware Bag Contents 1 1
More information11381 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-CURRENT MAKE: BMW MODEL: -SERIES STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 40454 XM SATELLITE RADIO 2009 S2000 Issue Date AUG 2008 PARTS LIST Template XM Radio Unit Kit (sold separately): P/N 08A53-S2A-101 XM
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25830 2004 MDX Issue Date SEP 2003 PARTS LIST 2 Clips Trailer Hitch Kit: P/N 08L92-S3V-200A Receiver cover Trailer hitch Harness Kit:
More information54531/ FORD FUSION
54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill
More informationInstallation Instructions
Installation Instructions Page 1 of 15 November 2007 Equipment Parts, Trailer Hitch Version 3.0 Accessory Development These Installation Instructions supersede all previous versions. SUBJECT MODEL TRAILER
More informationINSTALLATION INSTRUCTIONS LD-1 REAR BUMPER RAM 1500 PART#R R #PW017838
INSTALLATION INSTRUCTIONS LD-1 REAR BUMPER PART#R102617 R102620 #PW017838 PARTS LIST: 1 LD1 Bumper Assembly 4 12-1.75mm x 40mm Hex Bolts 1 Push in License Plate Light 4 12mm x 37mm x 3mm Flat Washers 2
More informationTOYOTA 4-RUNNER TOWING HITCH Preparation
Preparation Part Number: PT228-89460 Kit Contents 1 1 High Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Frame Spacer 6 2 Center Spacer 7 1 Close-out Panel Hardware Bag Contents
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25877 PILOT Issue Date AUG 2003 Optional ATF and power steering coolers are required when installing the trailer hitch. 2 Spacers PARTS
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationInstallation Instructions 2019 Chevy and GMC 1500 Rear Bumper Product Number: E4050, E4051 Application: Chevy and GMC 1500 Trucks
IMPORTANT SAFETY GUIDE Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided the following warnings, safety precautions, installation
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2003 ELEMENT AII 24318 Issue Date DEC 2002 PARTS LIST Trailer Hitch Kit P/N 08L92-SCV-100 4 Bolts, 12 x 35 mm Trailer hitch U-bolt 2 Nuts,
More information2005 and 09 Mustang install instructions Sequential / Chase Unit Partial Plug-N-Play Kit Meter4it Eng. Updated: 3/28/09
Updated: 3/28/09 Verify content of kit: 1- Unit with wiring harness 1- Red power wire with 15 amp fuse 1- Color instruction 2- Velcro for mounting 1-Driver taillight harness 1- Passenger taillight harness
More information2010 Mustang V6 Shaker CDC #
- - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker
More information2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete E
BILLET GRILLS IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete 5122-1900-11E TOOLS REQUIRED Automotive
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More informationInstallation Instructions
Installation Instructions Application Fits 2011-2014 Subaru Impreza WRX Sedan X7279 & X7280 DOES NOT FIT HATCHBACK MODEL 2 & 1.25 EcoHitch Invisi 200 lbs. Tongue Weight/2,000 lbs Weight Carrying Torklift
More informationLEXUS GX TOWING HITCH Preparation
LEXUS GX460 2014 - TOWING HITCH Preparation Part Number: PT228-60140 Kit Contents Item # Quantity Reqd. Description 1 1 Hitch Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Center
More informationBX3821 Installation Instructions / VW Passat 1.8 L
BX3821 Installation Instructions 2001 1/2-2002 VW Passat 1.8 L The front fascia and metal bumper are removed for baseplate installation. There is trimming to air dam and lower grill opening (option to
More information11221 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-CURRENT MAKE: CHEVROLET MODEL: VOLT STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationInstallation Instructions
Installation Instructions Page 1 of 13 October 2006 Equipment Parts, Trailer Hitch Ver 4.0 Accessory Development These Installation Instructions supersede all previous versions. SUBJECT MODEL TRAILER HITCH
More information