INSTALL INSTRUCTIONS C-VS-1500-DUR-1 15 VEHICLE SPECIFIC CONSOLE for Dodge Durango with OEM Center Shifter
|
|
- Clementine Lyons
- 5 years ago
- Views:
Transcription
1 INSTALL INSTRUCTIONS C-VS-1500-DUR-1 15 VEHICLE SPECIFIC CONSOLE for Dodge Durango with OEM Center Shifter TOOLS NEEDED: Phillips Screw Driver Standard Socket set Metric Socket set 90 Phillips Screw Driver T-20 Torx Bit Wire Crimping tool Wire Cutters QTY DESCRIPTION PART # 1 Main Console Housing CM Base mount bracket CM Shifter mount platform CM Top console Bezel CM Shifter cover CM Driver side trim panel CM Passenger side trim panel CM Retaining bracket CM Nylock nut GSM Cup Holder CM Hardware kit C-HK-211 C-HK-211 Hardware Kit includes the following 2 12 volt socket CM /4 x 1/2 Hex head bolt GSM /4 x 3/4 Hex head bolt GSM /4 x 1 ¼ Hex head bolt GSM /4 x 1/2 Carriage bolt GSM /4 serrated nut GSM /4 Flat washer GSM /4 Lock washer GSM # 8 x 1/4 Flat head sheet metal screw GSM # 8 x 3/8 Torx head screw CM x 2 ½ x 8 foam block CM NOTES! Read all instructions before installing any Havis, Inc. products. Use hardware provided with install kit.
2 C-VS-1500-DUR-1 (Main Housing Assembly) CM Driver side cover panel CM Passenger side trim panel CM Shifter cover CM Cup Holder CM Top Console Bezel CM Retaining bracket CM Shifter mount platform (inside console) CM Main Console Housing CM Base mount bracket
3 O.E.M. console prior to removal Carefully slide down (unsnap) chrome trim piece under shifter knob. Carefully remove retaining clip that holds knob onto shifter shaft. (Needle nose pliers work well) Remove shifter knob Carefully pop out coin tray from console top panel and save to be reused. Note: Some vehicles may have the coin tray with traction control switch as shown. Carefully unclip and remove top console panel. Unplug wires as needed. Top console panel removed. Remove two (2) screws for side trim panels. (Phillips screwdriver) Remove bolt cover at lower rear end of console. (one each side). Remove bolts. (10 mm socket)
4 Carefully unclip and remove console rear end panel. Note: Some vehicles may have rear controls in panel that will require removal of electrical connectors. Remove arm rest and hinge assembly. (Phillips screwdriver) Carefully unclip and remove console side panels. Remove rear side screws holding housing to floor bracket. (90 Phillips screwdriver) Remove four (4) bolts holding the main plastic console housing to floor and Save hardware Unplug wire harnesses. Driver side / forward bolt shown. Remove four (4) bolts holding the shifter assembly to holding the main plastic console housing. Save Hardware (10mm socket) Unplug shifter harness from console base.
5 Carefully unclip shift cable mount and unbolt cable end. Take note of correct position of cable mount parts. Save Hardware Remove shifter assembly Remove forward base screws from lower dash and save screws.(one each side) (7 mm socket) Unplug main console harness from lower end of dash. Remove OEM plastic base plate O.E.M. console housing removed. Carefully remove wire harness from O.E.M. console housing. Place # CM base mount bracket into vehicle. Attach bracket to rear O.E.M. floor mount with O.E.M screws previously removed. (10 mm socket)
6 Attach base bracket to front O.E.M. floor mount with O.E.M screws previously removed. (10 mm socket) Attach # CM front shifter platform to base bracket with six (6) 1/4 x 1/2 Hex head bolts, lock washers and flat washers. (7/16 wrench) Place shifter assembly into base bracket. Do not bolt in yet. Carefully reattach shifter cable back onto original location and tighten cable end bolt. Reattach O.E.M. harnesses and plugs. Note: There some holes for attaching cable clips. Attach shifter assembly to shifter platform with three (3) 1/4 x 1¼ hex head bolts lock washers and flat washers. (7/16 socket) Insert 2 x 2.5 x 8 foam block into lower dash air duct to prevent air from blowing into console. Foam part number - CM Place coin tray on the underside of top console bezel. Clamp on with CM brackets as shown. (11/32 socket) Now coin tray is mounted to the console bezel. Proceed with installation of bezel. Note: Some vehicles may not have the traction control knob as shown. Carefully place main console housing into vehicle. Loosely attach rear housing sides to base bracket with 1/4 x 1/2" Carriage bolts and serrated nuts. (two each side) Do not tighten hardware yet.
7 Loosely attach front passenger side console housing to lower dash with previously removed O.E.M. screw. (7mm socket) Loosely attach front driver side console housing to lower dash with previously removed O.E.M. screw. (7mm socket) Loosely attach forward housing sides to base bracket with 1/4 x 3/4" hex bolts and flat washers. (two each side) Tighten all console mount hardware. Place top console bezel onto console. Note: Wire in the 12 volt sockets and run aftermarket wire harnesses before closing up front end of console. Attach angled shifter cover plate to top console bezel with four (4) # 8 x 1/4" flat head sheet metal screws. Note: You may need to slide bezel back to access forward screws. Push top console bezel forward and attach to console housing with # 8 x 3/8 Torx head screws (T-20 Torx) Reattach shifter knob and insert cup holder Attach driver side trim panel to console housing with # 8 x 1/4" flat head sheet metal screws.. Attach passenger side trim panel to console housing with # 8 x 1/4" flat head sheet metal screws. Note: If mounting a C-HDM-204 side computer mount, use the existing 1/4" hex bolts and nuts with 1/2" hex bolts in upper side extrusion. Before inserting cup holder, run necessary wiring and wire tie as needed. Make sure wiring is not stressed or that it does not interfere with shifter mechanism.
8 New console housing with control heads and accessories installed. View of console at rear end. Console includes mounting provisions for side mounted C-HDM-204 computer mount bracket. View of C-HDM side computer mount. View of completed installation on passenger side. View of completed console and laptop mount in a 2012 Dodge Durango.
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationINSTALL INSTRUCTIONS C-VS-1400-EQX-1 14 VEHICLE SPECIFIC CONSOLE for 2014 Chevy Equinox with OEM Center console
INSTALL INSTRUCTIONS C-VS-1400-EQX-1 14 VEHICLE SPECIFIC CONSOLE for 2014 Chevy Equinox with OEM Center console TOOLS NEEDED: Phillips Screw Driver Standard Socket set Metric Socket set Thin Tape T-20
More informationINSTALL INSTRUCTIONS C-VS-2000-TAH-2
INSTALL INSTRUCTIONS C-VS-2000-TAH-2 2015-2019 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (12.5 inches wide) 20 inches of Equipment mounting space Tools Required: Phillips Screw
More informationINSTALL INSTRUCTIONS C-VS-2000-TAH Chevy Tahoe (Special Service) Vehicle Specific Console 20 inches of Equipment mounting space
INSTALL INSTRUCTIONS C-VS-2000-TAH-1 2007-2014 Chevy Tahoe (Special Service) Vehicle Specific Console 20 inches of Equipment mounting space Tools Required: Phillips Screw Driver Standard Socket set T-20
More informationTools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool
INSTALL INSTRUCTIONS C-VS-1500-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (9 inches wide) 15 inches of Equipment mounting space Note: 2 inches of mounting space is
More informationTOOLS REQUIRED: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool
INSTALL INSTRUCTIONS C-VS-1200-INUT 2013-2018 FORD INTERCEPTOR UTILITY Fits Standard Interior and Optional Interior Upgrade (Code 65U) Vehicle Specific Console 12 inches of Equipment mounting space TOOLS
More informationTools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool
INSTALL INSTRUCTIONS C-VS-1013-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (9 inches wide) 23 inches of Equipment mounting space Tools Required: Phillips Screw Driver
More informationINSTALL INSTRUCTIONS C-VS-0812-TAH-1
INSTALL INSTRUCTIONS C-VS-0812-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console with 20 inches of Equipment mounting space Tools Required: Phillips Screw Driver Standard
More informationKK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel
More informationMOUNT BRACKET PARTS and HARDWARE: Installation parts with * come loose in hardware kit bag. Other parts are preassembled
INSTALL INSTRUCTIONS C-DMM-2006 Dash Monitor Mount 2017-2019 F-250, 350, 450 Pickup, F-450 and 550 Cab Chassis, 2015-2019 Ford F-150 and 2018-2019 Expedition Notes: 1. The C-DMM-2000 series Dash Monitor
More informationK9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN
K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for 2013-2018 FORD INTERCEPTOR SEDAN TOOLS Needed: Phillips Screw Driver Trim panel removal tools Caulk Gun Standard Socket set Metric Socket set Wire Cutters /Crimpers
More informationINSTALLATION INSTRUCTIONS C-DMM FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT
INSTALLATION INSTRUCTIONS C-DMM-123 2013-2018 FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system requires two or three main parts that are sold separately. See
More informationINSTALLATION INSTRUCTIONS
5 ALL VEHICLES KIT FEATURES Equalizer provisions Rear support provisions KIT COMPONENTS 99-7890 INSTALLATION INSTRUCTIONS -SHAFT HEAD UNITS: Snap the Shaft Supports into the Radio Housing. Slide the aftermarket
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationINSTALLATION INSTRUCTIONS C DMM Nissan Frontier SWING OUT DASH MONITOR MOUNT
INSTALLATION INSTRUCTIONS C DMM 134 2011 2018 Nissan Frontier SWING OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system may require two or three main parts that are Sold Separately. See web site
More informationAcura TSX 2009-up CH
INSTALLATION INSTRUCTIONS FOR PART KIT FEATURES ISO Double DIN radio provision Painted charcoal gray APPLICATIONS Acura TSX 2009-up Table of Contents Acura TSX 2009-up...2-5 Kit Assembly ISO Double DIN
More informationK9-C23 INSTALLATION INSTRUCTIONS K9 Kit for CHEVY TAHOE PPV (9C1)
K9-C23 INSTALLATION INSTRUCTIONS K9 Kit for 2015-2018 CHEVY TAHOE PPV (9C1) TOOLS Needed: Phillips Screw Driver Trim panel removal tool Caulk Gun Standard Socket set Wire Cutters /Crimpers Drill & Drill
More informationChrysler/Dodge/Jeep (without NAV)
Installation instructions for part 99-6507 Chrysler/Dodge/Jeep (without NAV) 2005-2010 99-6507 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket WIRING & ANTENNA CONNECTIONS
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationAcura/Honda/Isuzu AT-807HD, IBR-807HD, CF-807HD, AW-807HD
Installation instructions for part Acura/Honda/Isuzu 1988-2006 99-7898 AT-807HD, IBR-807HD, CF-807HD, AW-807HD WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: Not Required KIT FEATURES DIN
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More information2 Rubber Bumper GSM MM nut GSM30201 K9-F18-PT_INST_4-16
K9-F18-PT INSTALLATION INSTRUCTIONS K9 Kit for 2013-2019 FORD INTERCEPTOR UTILITY Vehicle Notes: 1. For K9 applications, it is recommended to order the Interceptor Utility with the OEM optional Aux Rear
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationRequired Parts and Tools
Welcome to the installation guide for the 2004 to 2009 CLK Class Mercedes Benz. Please thoroughly review this manual before installation as there are details that are essential to operation of the vehicle.
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationby B6 Boost Volkswagen -> (46) Golf & Jetta V (13) Passat B6 (11) Passat B5.5 (4) Phaeton (8) Eurovan (7) Touareg (3) Audi
1 of 10 Top» Volkswagen» Passat B6» European Cup Holder DIY Installations European Cup Holder by B6 Boost Volkswagen -> (46) Golf & Jetta V (13) Passat B6 (11) Passat B5.5 (4) Phaeton (8) Eurovan (7) Touareg
More informationMazda S
INSTALLATION INSTRUCTIONS FOR PART 99-7523S KIT FEATURES Double DIN radio provision ISO DIN radio provision with pocket Painted silver Pre-wired ASWC-1 harness included (ASWC-1 sold separately) APPLICATIONS
More informationInstallation Instructions HURST BILLET COMPETITION/PLUS SHIFTER Dodge Challenger
Installation Instructions HURST BILLET COMPETITION/PLUS SHIFTER 2009-2015 Dodge Challenger Catalog #3916020 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with
More informationor Chrysler Multikit 2007-up* TABLE OF CONTENTS See page 2 KIT FEATURES
95-6511 or 99-6511 INSTALLATION INSTRUCTIONS 95-6511 ISO DDIN radio provision Textured 99-6511 DIN radio provision with pocket ISO DIN radio provision with pocket KIT COMPONENTS 95-6511 A) Long nose (wide)
More informationChrysler Multi-kit TABLE OF CONTENTS Dash Disassembly...2 Kit Assembly
99-650345 INSTALLATION INSTRUCTIONS Chrysler Multi-kit 1998-2010 INTRODUCTION This instruction booklet will cover (3) different kits, yet carry the same applications and dash disassembly. After dash disassembly
More informationInstallation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed
Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationFord multi-kit 2004-up
INSTALLATION INSTRUCTIONS FOR PART 99-5812 APPLICATIONS See application list inside Ford multi-kit 2004-up 99-5812 KIT FEATURES DIN head unit provision with pocket ISO DIN head unit provision with pocket
More informationTOYOTA SOLARA EC REARVIEW MIRROR Section I - Installation Preparation
Section I - Installation Preparation Part Number: PT374-33020 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass 2 1 Hardware Bag 3 1 Installation
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationPassenger/Right Upper U- Bracket OE fog light only. Driver/Left Upper U- Bracket OE fog light only. Winch Tray
PARTS LIST: 1 HD Bull Nose Bumper 48 12mm x 32mm x 3mm Flat Washers 1 Driver/left Frame Bracket 28 12mm Lock Washers 1 Passenger/right Frame Bracket 28 12-1.75mm Hex Nuts 1 Winch Tray 1 Access Cover 2
More informationHD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:
PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for
More informationMINI COOPER HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT DESIGNED FOR USE WITH BALL MOUNT # D-19 / 45519
10/8/2012 PAGE 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED RATCHET TORQUE WRENCH 12" EXTENSION 12mm SOCKET 8mm SOCKET OFFSET SCREWDRIVER FLAT BLADE
More informationGenuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for Corvettes.
Genuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for 2005-2007 Corvettes. Difficulty: 3 out of 5. Time: Plan on about 1 hour. The tools used are: A small flashlight A
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Chrysler Multi Kit. A) Radio Housing B) ISO Trim Plate C) ISO Snap in Brackets
INSTALLATION INSTRUCTIONS FOR PART 99-60 APPLICATIONS Chrysler Multi Kit 99-60 KIT FEATURES DIN Head Unit Provision with pocket ISO DIN Head Unit Provision with pocket KIT COMPONENTS A) Radio Housing B)
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More informationM-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationPARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2)
Installation Instructions SHORT THROW SHIFTER Fits: Porsche Boxter, Boxter S, 911, 996 Cayman & Cayman S models See Application Guide for specific year ranges and engine sizes Catalog # 45135 WORK SAFELY!
More informationInstallation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion
Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion It s preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral.
More informationInstallation Instructions PISTOL GRIP HANDLE Fits: Dodge Challenger and Charger w/ Automatic Transmission Catalog #
Installation Instructions PISTOL GRIP HANDLE Fits: 2015-2018 Dodge Challenger and Charger w/ Automatic Transmission Catalog # 5380437 WORK SAFELY! For maximum safety, perform this installation on a clean,
More information1. Disconnect the battery. This is important! This will prevent air bag deployment.
PARTS PACKING LIST Evaporator assembly Drain tube Plastic air plug Hardware package 11040 3601 W. Clarendon Phoenix, Arizona 85019 (602) 233-0090 800-648-4475 www.ackits.com 2003-4 Jeep Wrangler EVAPORATOR
More informationTOYOTA TACOMA LED DRL. Part Number: TTA-712
Part Number: TTA-712 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware Bag Contents Item # Quantity Reqd. Description
More informationADVANCE ADAPTERS INC. P/N:
Paso Robles, CA 93447 PAGE 1 of 6 KIT CONSISTS OF: Qty Part No. Description 1 303303 SHIFTER BODY BARREL RETAINER 11 303311 HEAT SHIELD-FIREPROOF SLEEVE 1/2" 2 303312 BUSHING- IGUS 3/8" 2 303313 HEIM JOINT-
More informationPassenger/right Upper U- Bracket OE fog light only. Driver/Left Upper U- Bracket OE fog light only. Winch Tray
PARTS LIST: 1 Elevation Bull Nose Bumper 48 12mm x 32mm x 3mm Flat Washers 1 Driver/left Frame Bracket 28 12mm Lock Washers 1 Passenger/right Frame Bracket 28 12-1.75mm Hex Nuts 1 Winch Tray 2 8-1.25mm
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationTru-Billet Climate Control Knob Installation Instructions
P/N S197-525-07 2007-08 Tru-Billet Climate Control Knob Installation Instructions Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the installation.
More informationInstallation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter
Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the
More information97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS
92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best
More informationInstallation Manual TWM Performance Honda Accord 2008+
Installation Manual TWM Performance Honda Accord 2008+ Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationPARTS LIST: HEAVY DUTY FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: HEAVY DUTY FRONT BUMPER 1 Heavy Duty Bumper Assembly 18 12-1.75mm x 50mm Hex Bolts 1 Driver/Left Frame Mounting Bracket 36 12mm x 32mm x 3mm Flat Washers 1 Passenger/Right Frame Mounting Bracket
More informationTOYOTA AVALON EC REARVIEW MIRROR
Section I - Installation Preparation Part Number: PT732-07000 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Full Mirror Assembly, Compass 2 1 Hardware Bag 3 1
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More informationMobile Video Installation Guide
000MVGUIDE Revision 04/29/04 Mobile Video Installation Guide This installation guide offers examples of mobile video system types and suggested layouts. The installation of your system will depend upon
More informationInstallation Manual TWM Performance Short Shifter Subaru STi 2008+
- 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationMANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER
MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER P.O. BOX 313 ~ ODESSA, FL 33556 ~ 1-844-NUM-RACE Tools Needed T20 Torx Driver T27 Torx Driver Needle Nose Pliers ¼ Ratchet with 10MM Socket 3MM Allen Wrench
More information8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationChevrolet Camaro 2010-up S-LC
INSTALLATION INSTRUCTIONS FOR PART 99-10S-LC APPLICATIONS Chevrolet Camaro 2010-up 99-10S-LC KIT FEATURES DIN and DDIN head unit provision Painted silver to match factory dash AXXESS Interface included
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationADVANCE ADAPTERS INC. P/N:
Paso Robles, CA 93447 PAGE 1 of 6 KIT CONSISTS OF: Qty Part No. Description 1 303303 SHIFTER BODY BARREL RETAINER 11 303311 HEAT SHIELD-FIREPROOF SLEEVE 1/2" 2 303312 BUSHING- IGUS 3/8" 2 303313 HEIM JOINT-
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationAPPROXIMATE ASSEMBLY TIME (R&R): 45 minutes -1-
PLOW ANGLE CONTROL KIT P/N 2879224 Application For use with the Glacier Pro Plow System P/N 2879103 on the below listed models MY09 and newer full size Ranger 500, 700 & 800 models MY13 and newer Ranger
More informationNissan Sentra (without pocket door)
INSTALLATION INSTRUCTIONS FOR PART 99-7422 APPLICATIONS See application list inside Nissan Sentra 2007-2012 (without pocket door) 99-7422 KIT FEATURES DIN radio provision with pocket Double DIN radio provision
More informationPARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs
More informationAir Conditioner for M915 A0/A1 Truck
RD-2-4530-0 Air Conditioner for M915 A0/A1 Truck INSTALLATION INSTRUCTIONS Install refrigerant compressor per instructions provided with compressor mount kit. CAUTION: Edges of sheet metal can be sharp!
More informationInstallation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #
Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,
More informationPART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationInstallation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only)
Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER 2005-2010 Mustang w/5-speed Manual Transmission (GT only) Catalog# 3915201 WORK SAFELY! For maximum safety, perform this installation
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS GM/SUZUKI MULTI KIT
INSTALLATION INSTRUCTIONS FOR PART 99-2003 APPLICATIONS GM/SUZUKI MULTI KIT 99-2003 KIT FEATURES DIN Head Unit Provisions with Pocket ISO DIN Head Unit Provisions with Pocket Double DIN head unit provision
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationInstallation Manual TWM Performance Short Shifter Subaru Forester up to 2005
- 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationNissan 370Z 2009-up (without navigation) B
REV. 4/2/2014 INST99-7607B INSTALLATION INSTRUCTIONS FOR PART 99-7607B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte black to match
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REMOTE ENGINE STARTER SYSTEM 2008 CIVIC 2-DOOR AII 38215 Issue Date OCT 2007 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationGentex Autodim Homelink Compass Temperature Mirror Installation in 2014 Tacoma Purchased from Bob s Automotive Mirrors & More LLC (Robert Prim)
Gentex Autodim Homelink Compass Temperature Mirror Installation in 2014 Tacoma Purchased from Bob s Automotive Mirrors & More LLC (Robert Prim) This is my 50-GENK51A Gentex mirror kit and instructions.
More information(Ford Transit Rear Bumper) INSTALLATION INSTRUCTIONS
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 (Ford Transit Rear Bumper) INSTALLATION INSTRUCTIONS Please read before beginning Stainless steel hardware may bind together
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationSUBARU/VOLVO VOLKSWAGEN INSTALLATION INSTRUCTIONS (pgs. 1-6) (pgs. 7-10)
3b 4 5 C A B D Fig. C Fig. D 00 SERIES (LOWER DASH), 00 SERIES: For -Shaft head units, slide the aftermarket head unit into the Radio Housing and secure with shaft nuts. (see ). For DIN head units, cut
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More informationTOYOTA CAMRY EC REARVIEW MIRROR Preparation
TOYOTA CAMRY 2010 - EC REARVIEW MIRROR Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ Compass 2 1 Hardware bag Hardware Bag Contents
More informationLincoln Navigator / MKX Lincoln MKZ / Zephyr 2006 (excludes models equipped with factory navigation)
99-5813 INSTALLATION INSTRUCTIONS Lincoln Navigator 2007-2014 / MKX 2007-2010 Lincoln MKZ 2007-2009 / Zephyr 2006 (excludes models equipped with factory navigation) KIT FEATURES DIN radio provision with
More informationMercedes Benz SLK Class
INSTALLATION INSTRUCTIONS FOR PART 99-8713 KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision APPLICATIONS See application list inside Mercedes Benz
More information2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions
2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationINSTALLATION INSTRUCTIONS DRAWERS #240
INSTALLATION INSTRUCTIONS DRAWERS #240 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS #1 Lid #2 Rear #3 Left side panel #4 Right side panel
More information