10 PSE53 0 M5. Port size. M5 x 0.8 ø6 reducer 1/4-inch reducer. the cable at the time of shipment. 10-PSE to -101 kpa

Size: px

Start display at page:

Download "10 PSE53 0 M5. Port size. M5 x 0.8 ø6 reducer 1/4-inch reducer. the cable at the time of shipment. 10-PSE to -101 kpa"

Patrick Wade
5 years ago
Views:

Series 0-PSE50 Remote type pressure sensor How to Order Clean series 0 PSE5 0 M5 Pressure sensing range Option 0 2 High pressure [0 to MPa] Vacuum [0 to 0 kpa] Low pressure [0 to 0 kpa] Compound

1 Series 0-PSE50 Remote type pressure sensor How to Order Clean series 0 PSE5 0 M5 Pressure sensing range Option 0 2 High pressure [0 to MPa] Vacuum [0 to 0 kpa] Low pressure [0 to 0 kpa] Compound pressure [ 0 to 0 kpa] M5 R06 Port size M5 x 0.8 ø6 reducer /4-inch reducer Nil L Without cable Sensor cable ( m) Option When only optional parts are required, order using the part numbers listed below. Description Part no. Note Connector Sensor cable 0-ZS-28-C 0-ZS-26-F pc. per set Cable length: m Connector for pressure sensor controller Cable length: m 0-ZS-26-J The connector is not connected to connection + Sensor cable the cable at the time of shipment. Specifications C2L Connector for pressure sensor controller connection (pc.) + Cable for sensor (m) Note) At the factory, the connector is not connected to the cable, but packed together with it for shipment. Model 0-PSE50 0-PSE5 0-PSE52 0-PSE5 Rated pressure range Proof pressure 0 to MPa.5 MPa 0 to -0 kpa 0 to 0 kpa 500 kpa -0 to 0 kpa Fluid Power supply voltage Current consumption Output specification Accuracy (Ambient temperature of 25 C) Linearity Repeatability Power supply voltage effect Enclosure Operating temperature range Withstand voltage Insulation resistance Vibration resistance Impact resistance Temperature characteristics Sensor cable / Option Particle generation grade (Refer to front matter pages to 22 for details.) Air, Non-corrosive gas, Non-flammable gas 2 to 24 VDC, Ripple (p-p) 0% or less (with power supply polarity protection) 5 ma or less (at no load) Analog output ( to 5 V, Output impedance: Approx. kω) ±2% F.S. or less ±% F.S. or less ±% F.S. or less ±% F.S. or less based on the analog output at 8 V ranging from 2 to 24 VDC IP40 Operating: 0 to 50 C; Stored: -0 to 70 C (No freezing or condensation) 000 VAC, 50/60 Hz for minute between live parts and case 5 MΩ between live parts and case (measured by 500VDC megameter) 0 to 500 Hz at whichever is smaller of.5 mm amplitude or 98 m/s 2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized) 980 m/s 2 in X, Y, Z directions, times each (De-energized) ±2% F.S. or less (based on 25 C) Halogen-free heavy-duty cord, ø2.7, 0.5 mm 2, cores, m Grade 2 Environmental resistance This product is blown with air and double packed in a Class M.5 (ISO Class 5) clean room. Piping specifications Port size Model M5 M5 x 0.8 male R06 ø6 reducer type /4-inch reducer type Wetted parts material Body: Stainless steel 04 Pressure sensor: Silicon, O-ring: FKM Body: PBT Weight With sensor cable ( m) Without sensor cable 4 g 7 g 8 g.8 g 950

2 Remote type pressure sensor 0-PSE50 Internal circuit Analog output 0-PSE5 Voltage output style to 5V Output impedance Approx. kω Dimensions Main circuit kw Brown DC (+) Black OUT (Analog output) Load Blue DC ( ) + 2 to 24 VDC to 5 VDC Analog output (V) 5 A Air cylinder Rotary actuator 0-PSE5 -M M5 x 0.8 Pressure port ø2.5 ø Air gripper Directional control valve Fittings & Tubing Clean gas filter Pressure switch 5.4 ø2 ø7.2 0-PSE5 -R Pressure port Flow control 5.4 ø2 ø7.2 ød B Range Rated pressure range A B Vacuum 0 to 0kPa 0 0kPa Compound 0 kpa to 0kPa 0kPa 0kPa pressure Low pressure 0 to 0kPa 0 0kPa Positive 0 to MPa 0 MPa pressure 0 to 500kPa 0 500kPa Pressure (mm) Model Applicable fitting size (D) 0-PSE5 -R PSE5 - /4" With sensor cable ø0.4 ø Filter, Pressure control Air preparation 95

4 Remote type pressure sensor 0-PSE5 Specific Product Precautions Be sure to read before handling. Air cylinder Pressure sensor Warning Handling. Do not drop, bump or apply excessive impacts (0-PSE50 and 540: 980m/s 2, 0-PSE560: 500m/s 2, PSE550: 00m/s 2 ) while handling. Although the body of the sensor may not be damaged, the inside of the sensor could be damaged and lead to a malfunction. 2. The tensile strength of the cord is 2N for 0-PSE50 and not more than 50N for 0-PSE540, 550, and 560. If the applied force exceeds this specification, the sensor will be damaged.. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. (0-PSE50). Do not exceed the screw-in torque of.5 N m when installing piping. Exceeding this value may cause malfunction of the sensor. 2. Connecting the sensor cable (optional) Hold the female connector of the sensor cable with your fingers and carefully insert it into the connector. Sensor Male connector Female connector A connector cover is provided as part of the cable assembly. It is designed to keep the female connector from slipping out of the sensor. To lock the connector cover in place, first make sure it is facing in the right direction as you slip it over the female connector, then lock it to the sensor body by turning it clockwise. To remove the cover, first unlock it by turning it counterclockwise, then pull back on it. To remove the female connector, grab it with your fingers and pull back on it. Do not pull on the cable. Lock Unlock Sensor Connector cover (0-PSE540/550). Care should be taken when stripping the outer cable covering as the insulator may be accidentally torn or damaged if incorrectly stripped. Sensor series Sumitomo M 0-PSE FL 0-PSE FL 0-PSE FL 0-PSE FL Wiring. Connecting sensor cable and connector Cut the sensor cable as illustrated to the right. Referring to the table below, insert each lead wire of the cable at the position marked with a number corresponding to the color of the lead wire. Sheath 20mm or more Confirm that the numbers on the connector match the colors of the wires and that the wires are inserted to the bottom. Press Part A by hand for temporary fixing. Connector no. 2 4 Press in the central part of Part A vertically with a tool such as pliers. A sensor connector cannot be taken apart for reuse once it is crimped. If the wire arrangement is incorrect or if the wire insertion fails, use a new sensor connector. For connection to SMC pressure sensor monitors, use sensor connectors (ZS- 28-C ) or e-con connectors listed below. Tyco Electronics AMP K.K Insulator Wire core color Brown (DC (+)) Unconnected Blue (DC ( )) Black (OUT: to 5V) Section A Omron Corporation For detailed information about e-con connectors, please consult the manufacturers of the respective connectors. Rotary actuator Air gripper Directional control valve Flow control Filter, Pressure control Fittings & Tubing Air preparation Pressure switch Clean gas filter 97

5 Remote type pressure sensor 0-PSE5 Specific Product Precautions Be sure to read before handling. Warning Pressure source (0-PSE560). Use of toxic, corrosive or flammable gases Do not use toxic or corrosive gases with the sensors. 2. Fluid The fluid contact (wetted) areas are SUS6L (pressure sensor, fittings). Use fluid that will not corrode the materials. (For corrosiveness of fluid, consult with the manufacturer of the fluid.) A2 (0-PSE56 - B2 only) Helium leakage test Helium leakage test is conducted on the welding parts. Use a ferrule (Swagelok ) by Crawford Fitting Co. as the TSJ fittings, and packing, ground, etc. (VCR fittings) by Cajon as the URJ fittings. If a ferrule, packing or ground by other manufacturers are to be used, conduct helium leakage test before using them. Piping connection (0-PSE550) Air tubing Cut the air tubing vertically. Carefully hold the air tubing and slowly push it into the resin pipe, ensuring that it is inserted by more than 8mm. For your information, the pull strength is Resin pipe approx. 25 N when inserted by more than 8mm. Insert the low pressure tubing into Lo pipe, and the high pressure tubing into Hi pipe. When the air tubing of the brand other than SMC is to be used, its ID accuracy is required to be ø4±0.mm. Air tubing should be inserted surely into the pipe so that it will not come off. (Pull strength is about 25N in 8mm insertion. ) 972

Low Differential Pressure Sensor ±1% F.S.

CAT.ES100-49 A Low Differential Pressure Sensor Rated differential pressure range: 0 to 2 kpa Accuracy: ±1% F.S. LED display to confirm energization Series PSE550 Proof pressure: 65kPa Output: 1 to 5VDC