Anderson Greenwood M4TL Liquid Level Manifolds
|
|
|
- Meryl Little
- 5 years ago
- Views:
Transcription
1 A single-flanged, two-valve manifold consisting of two block valves with no equalizer passage suitable for pressures up to 6000 psig (414 barg) Features General application The manifold is designed for direct mounting to ΔP-style differential pressure transmitters in liquid level service on pressurized vessels. Technical data Materials: CS, SS, Hastelloy Seats: Metal or soft Connections: ½ NPT Pressure (max.): 6000 psig (414 barg) Temperature (max.): 1000 F (538 C) Cost savings of 20-30% when manifolding instruments by eliminating several parts used in conventional methods of piping up. Compact design requires minimum space for operation and installation. Free-swivelling ball end stems ensure bubble-tight valve closure without seat galling. Easy instrument removal due to direct bolting to the manifold. Signal lines, purge lines, etc. are left undisturbed, facilitating repairs, service and calibration. Immediate installation with AGCO Mount as the manifold, steam block, bracket and all associated piping can be installed without the instrument at the time of plant construction. Secure mounting ensured by the AGCO Mount. Instrument piping stability is enhanced when supported directly by the pipe stand through the manifold. All packing is below stem threads, body-to-bonnet seal is below the threads minimizing process fluid corrosion. Reduced chance of instrument damage. With the AGCO Mount, the instrument can be warehoused safely until final loop checkout Emerson. All rights reserved. VCTDS EN 16/02
2 Metal Seat (Soft Seat available) Dimensions, inches (mm) 1.70 [43.2] 3.40 [86.4] 0.81 [20.6] 1.62 [41.1] Instrument side 2.38 [60.5] 2.41 [61.2] 3.70 [94.0] 0.94 [23.9] ½ - 14 NPT process connection 2 places 2.12 [53.8] A Max. open Ø 0.38 (9.6) Mounting holes 2 places Dimensions, inches (mm) Packing A PTFE 8.60 (218.4) GRAFOIL 9.90 (251.5) Block/ isolate Instrument Block/ isolate Process Standard Materials Valve Packing Body Bonnet Stem Ball Bolts CS [2] PTFE A576 10L18 A108 A PH A193-B7 CS [2] GRAFOIL / A576 10L18 A105 A PH A193-B7 SS PTFE A A A A193-B7 SS GRAFOIL / A A A A193-B7 SG [3] PTFE A Monel 400 Monel K500 A193-B7 PTFE SG [3] GRAFOIL / A A Monel 400 Monel K500 A193-B7 SG3 [4] PTFE Hastelloy C-276 Hastelloy C-276 Hastelloy C-276 Elgiloy A193-B7 Notes 1. Approximate valve weight: 5.0 lb (2.3 kg). Metal seat: inch (4.0 mm) diameter orifice. Valve C v 0.36 maximum. Soft seat: inch (4.8 mm) diameter orifice. Valve C v 0.83 maximum. 2. CS is zinc chromate plated to prevent corrosion. 3. SG (Sour Gas) meets the requirements of NACE MR0175/ISO (for chloride conditions 50 mg/l (ppm)) and NACE MR SG3 (Sour Gas) meets the requirements of NACE MR0175/ISO (for chloride conditions > 50 mg/l (ppm)) SS bolts lower pressure ratings to a maximum of 4500 psig (310 barg). Consult factory for full ratings. 2
3 Bonnet assembly options The 4TL has metal seats as standard with the option of soft seated designs. All stem threads are rolled and lubricated to prevent galling and reduce operating torque. The stem seal is a patented PTFE packing gland which is adjustable in service. All bonnets are assembled with a bonnet locking pin to prevent accidental removal while in service and a protective dust cap is fitted to contain stem lubricant and prevent the influx of contaminants. Metal-seated bonnet assemblies The metal-seated bonnet assemblies have a rotating stem with free swivel ball-type seat for long service life. The specially hardened ball seat is ideal for both gas and liquid service. Soft-seated bonnet assemblies The soft-seated bonnet assemblies have a one-piece rotating stem and plug. In addition to the adjustable PTFE packing gland, the bonnets are available with a FKM O-ring and PTFE back-up ring. Pressure and temperature ratings Valve Packing Ratings CS [1] PTFE 6000 psig at 200 F (414 barg at 93 C) 4000 psig at 500 F (276 barg at 260 C) CS [1] GRAFOIL / 6000 psig at 200 F (414 barg at 93 C) 4000 psig at 600 F (276 barg at 316 C) SS PTFE 6000 psig at 200 F (414 barg at 93 C) 4000 psig at 500 F (276 barg at 260 C) SS GRAFOIL / 6000 psig at 200 F (414 barg at 93 C) 1500 psig at 1000 F (103 barg at 538 C) SG [2], SG3 [3] PTFE 6000 psig at 200 F (414 barg at 93 C) 4000 psig at 500 F (276 barg at 260 C) SG [2] ), SG3 [3] GRAFOIL / 6000 psig at 200 F (414 barg at 93 C) 1500 psig at 1000 F (103 barg at 538 C) Notes 1. CS is zinc chromate plated to prevent corrosion. 2. SG (Sour Gas) meets the requirements of NACE MR0175/ISO (for chloride conditions 50 mg/l (ppm)) and NACE MR SG3 (Sour Gas) meets the requirements of NACE MR0175/ISO (for chloride conditions > 50 mg/l (ppm)) SS bolts lower pressure ratings to a maximum of 4500 psig (310 barg). Consult factory for full ratings. 5. Minimum temperature: -70 F (-57 C). Pressure vs. Temperature Pressure psig (barg) 6000 [414] 5000 [345] 4000 [276] 3000 [207] M4TLHIS-4 M4TLEIS-4 M4TLHIC-4 M4TLEIC-4 M4TLVIC-4 M4TLVIS-4 Denotes intersecting data 2000 [138] 1500 [103] 1000 [69] 0 0 [-18] 100 [38] 200 [93] 300 [149] 400 [204] 500 [260] 600 [316] 700 [371] 800 [427] 900 [482] 1000 [538] Temperature F ( C) 3
![AGCO Mount kits Flow 5.0 [126.0] 4.5 [114.0] 3.0 [76.0] AGCO Mount kits are available for all manifolds where they apply. See AM option for each manifold.](/docs-images/89/100178253/images/4-0.jpg "AGCO Mount kits for liquid level manifold Manifold style Description Material M4TL Standard kit CS, zinc chromate plated For bottom test ports With steam block M4TL Standard kit SS For")
4 AGCO Mount kits Flow 5.0 [126.0] 4.5 [114.0] 3.0 [76.0] AGCO Mount kits are available for all manifolds where they apply. See AM option for each manifold. AGCO Mount kits for liquid level manifold Manifold style Description Material M4TL Standard kit CS, zinc chromate plated For bottom test ports With steam block M4TL Standard kit SS For bottom test ports With CS steam block 4
5 Selection guide Example: M4TL V I C AM Packing V PTFE H Grafoil Seat material I Integral (body material) Body material C CS, A576-10L18 S SS, A W 316L SS J Hastelloy Connections 4 Flange outlet x ½-inch FNPT (inlet) Connection style B Female socket weld Options AM AGCO mount AMMS AGCO mount kit -multi mount-stainless AMV AGCO mount kit (vertical) AMVS AGCO mount kit (vertical stainless steel) AMW AGCO mount kit (wall mounting) BL Bonnet lock device CL00 Chlorine cleaning (CL) HD Hydrostatic testing (100%) (MSS-SP-61) OC00 Oxygen clean (OC) PMI00 PMI body only PT Top purge port ¼" R3V Add for use with Rosemount model 305C (SS 18-8 Bolts) SB Steam block SG (Sour Gas) NACE edition 2003 /MR0103 SG3 (Sour Gas) NACE MR0175/ISO (latest edition) SS All 316 SS construction SSB 316 SS flange bolt (B8M Class 2) - will provide full pressure rating SSC 316 flange bolt (B8M) - maximum pressure rating 4500 psi [310 barg] SSD 696 material bolt T Large diameter gasket groove TB Bottom test port ¼" TF Top test ports ¼" FNPT XP ASME B31.1 (with Grafoil bonnets only) OR O-ring gasket Note SS bolts lower pressure ratings to a maximum of 4500 psig (310 barg). Consult factory for full ratings. 5
6 2017 Emerson. All rights reserved. 6
ANDERSON GREENWOOD M4AP/M4TP STATIC PRESSURE MANIFOLDS
ANDERSON GREENWOOD M4AP/M4TP STATIC PRESSURE MANIFOLDS Block and bleed, two valve manifolds with indirect and direct mount capabilities for static pressures to 6000 psig (414 barg) FEATURES GENERAL APPLICATION
Anderson Greenwood MB Series Integral Manifolds
A range of 2, 3 or 5-valve integral manifolds for connection to bottom inlet, low-profile pressure transmitters Features MB2 General application MB3 The MB series includes 2 valve manifolds for static
ANDERSON GREENWOOD MC/MT SERIES INTEGRAL MANIFOLDS
A range of 2, 3 and 5 valve integral manifolds to be used with Rosemount Coplanar style transmitters for static and differential pressure applications FEATURES MC2 MT2 GENERAL APPLICATION MC3 The MC/MT
Anderson Greenwood M25/M251 Block and Bleed Gauge Valves
Two-valve single outlet gauge valves that combine isolating, calibrating and venting facilities in a single compact unit Features General application These valves enable gauges, pressure transmitters or
Anderson Greenwood M1/M110 Differential Pressure Manifolds
A 3-valve differential pressure manifold with integral metal seats or replaceable, roddable soft seats for applications requiring remote mounting from the instrument Features General application The M1
Anderson Greenwood PTM/PT7 Static Pressure Manifolds
m o Anderson Greenwood PTM/PT7 Static Pressure Manifolds Two valve calibration manifolds with a choice of metal and soft seats for static pressures up to 6000 psig (414 barg) PT7 PTM Features Cost savings
Anderson Greenwood M24A/M24T Differential Pressure Manifolds
Lightweight and compact 5 valve manifolds designed for direct mounting to differential pressure transmitters for pressures to 6000 psig (414 barg) Features Direct mounting compact design requires minimum
ANDERSON GREENWOOD H7/H71 HAND VALVES
3 /16 (4.8 mm) orifice hard-seated hand valves for pressures to 6000 and 10000 psig (414 and 689 barg) FEATURES H7 GENERAL APPLICATION H7 series valves are designed for safe, repetitive bubble-tight closure,
Natural Gas Manifolds M6A, M6T, M6TA 5-Valve Manifolds
Natural Gas Manifolds M6A, M6T, M6TA 5- Manifolds Features and Benefits M6A M6A Easy Installation. The lightweight M6A is easily installed in meter tubing. No additional support is generally required.
ANDERSON GREENWOOD M25/M25A/M25B/M251/M251B MANIFOLDS
Versatile two-valve static pressure manifolds with a variety of inlet and outlet connections that enable isolation, calibration and venting in single unit FEATURES M25 M25A Remote mounting compact design
Static Pressure Manifolds M4AP and M4TP Manifolds
Static Pressure Manifolds M4AP and M4TP Manifolds Product Overview The M4AP and M4TP are block and bleed, static pressure manifolds. They are designed for use with DP-style pressure transmitters. The manifold
ANDERSON GREENWOOD SERIES M9 BLOCK AND BLEED GAUGE VALVES
A valve with an interchangeable hard or soft seat and an integral bleed plug specifically designed to facilitate safe, compact, economical gauge installation and operation FEATURES GENERAL APPLICATION
Static Pressure Manifolds M25, M25A, M25B, M251 and M251B
Product Overview The M25, M25A, M25B, M25 and M25B are versatile two-valve manifolds with a variety of inlet and outlet connections. Lightweight and with compact dimensions, M25/M25 manifolds enable isolation,
Kerotest KM4AP & KM4TP Static Pressure Manifolds
Kerotest KM4AP & KM4TP Static Pressure Manifolds KM4AP KM4TP Product Brief The KM4AP and KM4TP are two-valve, block and bleed style manifolds. These manifolds are intended for static pressure applications
Anderson Greenwood Series M9 Block and Bleed Gauge Valves
A valve with an interchangeable hard or soft seat and an integral bleed plug specifically designed to facilitate safe, compact, economical gauge installation and operation Features General application
Gauge Valves. Block and Bleed Valves Multi-Port Valves OS&Y Valves
Gauge Valves Block and Bleed Valves Multi-Port Valves OS&Y Valves Anderson Greenwood is the industry leader in instrument valve technology and the original innovator of the 3-valve manifold. Our capabilities
Static Pressure Manifolds PTM and PT7 2-Valve Manifolds
Static Pressure Manifolds PTM and PT7 2-Valve Manifolds PT7 PTM Product Overview The PT Two-Valve Calibration Manifolds are used on static pressure transmitters, switches or gauges. The shutoff valve,
Anderson Greenwood Instrumentation Products - Manifolds and Accessories
Anderson Greenwood Instrumentation Products - Manifolds and Accessories Total Flow Control Solutions Flow, Static Pressure and Liquid Level Manifolds Flow Control ANDERSON GREENWOOD INSTRUMENTATION PRODUCTS
Multi-Port Gauge Valves M5 and M51
Multi-Port Gauge Valves M5 and M51 M5 Product Overview The M5 and M51 are multi-port gauge valves allowing the versatile positioning of gauges or pressure switches without requiring additional penetration
ANDERSON GREENWOOD LARGE BORE INTELLIMOUNT SYSTEM
Large bore direct mount 2, 3 or 5 valve manifold system with renewable block valve metal or soft seats and graphite or PTFE stem packings that reduces potential leakpoints FEATURES Close coupled straight
ANDERSON GREENWOOD. Hand Valves and Accessories INSTRUMENTATION PRODUCTS. Soft Seated Valves Hard Seated Valves Mini Valves
ANDERSON GREENWOOD INSTRUMENTATION PRODUCTS Hand Valves and Accessories Soft Seated Valves Hard Seated Valves Mini Valves Anderson Greenwood is the industry leader in instrument valve technology and the
Manifold and Isolation Valve Mounting System for Direct Mounting DP Transmitters
ANDERSON GREENWOOD INSTRUMENTATION PRODUCTS for Direct Mounting DP Transmitters Introduction The Anderson Greenwood SaddleMount has been developed to overcome the problems associated with traditional transmitter/manifold
Distributed By: M&M Control Service, Inc
The KM1 is a 3-valve manifold designed for applications where direct mounting to an instrument is impractical or undesirable. This style manifold is mounted to the lines from the instrument and signal
VALVES & CONTROLS ANDERSON GREENWOOD INSTRUMENTATION PRODUCTS LARGE BORE INTELLIMOUNT SYSTEM
VALVES & CONTROLS ANDERSON GREENWOOD INSTRUMENTATION PRODUCTS Stabilized Connector (Futbol) System, The next generation of manifold systems Product overview The Large Bore IntelliMount direct mount manifold
General Specifications
General Specifications GS 22B01C52-01EN-A M-650, M-750 and M-651 3-Valve Manifolds for Differential Pressure INTRODUCTION The PGI 3-Valve manifolds are designed for mounting on differential pressure transmitters
3/8-inch [9.5 mm] (optional 5/8-inch [16 mm]) bore, 6000 psig [414 barg], API Firesafe 607 rated
![3/8-inch [9.5 mm] (optional 5/8-inch [16 mm]) bore, 6000 psig [414 barg], API Firesafe 607 rated](/thumbs/85/92772568.jpg "3/8-inch [9.5 mm] (optional 5/8-inch [16 mm]) bore, 6000 psig [414 barg], API Firesafe 607 rated")
M50 and H70 ANDERSON GREENWOOD 3/8-inch [9.5 mm] (optional 5/8-inch [16 mm]) bore, 6000 psig [414 barg], API Firesafe 607 rated Features and Benefits Cost savings are realized as the root valves are in-line
General Specifications
General Specifications GS 22B01C53-01EN-A M-675, M-775 and M-678 5-Valve Manifolds for Natural Gas Differential Pressure INTRODUCTION The PGI 5-Valve manifolds are designed for natural gas service and
MANIFOLDS VALVE. Mfg & Exp. : Valves & Fittings. A Trusted Name in Valves and Fittings ISO 9001:2008 COMPANY. Catalogue No.
A Trusted Name in Valves and Fittings Mfg & Exp. : Valves & Fittings MANIFOLDS VALVE ISO 9001:2008 COMPANY Pressure Ratings: 6,000 PSI/10,000 PSI NPT, ISO/BSP, Threads 2-,3- and 5-valves Instrument manifolds
Rosemount Manifolds. Rosemount Manifolds. Product Data Sheet , Rev LA Catalog Contents
Product Data Sheet Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and inline designs Integral design enables flangeless valve integration 2, 3,
P3M3H, P6M3H 3-VALVE HARD SEAT MANIFOLD
3-VALVE MANIFOLD 3/16 and 3/8 Bore 3-valve Manifold The 3-valve hard seat manifold designed for instrument calibration incorporates two shut-off valves and an equalizing valve in a single body. The manifold
Solution Partner. Leak - Proof Flow & Control. Manifold & Gauge & Rising Plug Valves. W e. s u p p o r t. t h e
W e. s u p p o r t. t h e i n n o v a t i o n s. o f. c u s t o m e r s Leak - Proof Flow & Control The Best Partner for Value Creation Solution Partner Manifold & Gauge & Rising Plug Valves 2 Manifold
Rosemount Manifolds. Rosemount Manifolds. Product Data Sheet , Rev NB January Contents
Product Data Sheet Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and inline designs Integral design enables flangeless valve integration 2, 3,
Rosemount Manifolds. Product Data Sheet October , Rev PB. Factory assembled, leak-tested, and calibrated
Product Data Sheet October 2014 00813-0100-4733, Rev PB Rosemount Manifolds Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and in-line designs
5030/5130. Hard Seat & Soft Seat/Tip. Flow Schematic. Manifold Valves, 5-Valve Natural Gas
Manifold Valves, 5-Valve Natural Gas Hard Seat & Soft Seat/Tip 5030/5130 Flare Pattern option Flow Schematic Designed for use with differential pressure transmitters incorporating two gas applications
Rosemount Manifolds. Product Data Sheet September , Rev PA. Factory assembled, leak-tested, and calibrated
Product Data Sheet September 2014 00813-0100-4733, Rev PA Rosemount Manifolds Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and in-line designs
Recognized globally for our quality, service and the ability to deliver! ISO 9001: Quality Service Experience
Recognized globally for our quality, service and the ability to deliver! ISO 9001:2008 Quality Service Experience www.mac-weld.com CONTENTS Introduction Page 1-2 Needle Valves Page 3-6 Gauge Valves Page
Rosemount Manifolds. Rosemount Manifolds. Product Data Sheet , Rev MA August Contents
Product Data Sheet Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and inline designs Integral design enables flangeless valve integration 2, 3,
Enclosures and Sunshades
ANDERSON GREENWOOD INSTRUMENTATION PRODUCTS Enclosures and Sunshades EM Manifolds Accessories and Mounting To maintain the integrity of process measurement instrumentation, protection from the effects
115 Series, Needle Valves, Single Block, Male x Male
115 Series, Needle Valves, Single Block, Male x Male Conformance Standards NACE MR0175 / ISO 15156, NACE MR0103 / ISO 17495 CRN (Canadian Registration Number) Approved/Registered ASTM B31.3 Process Piping,
instrument manifolds Instrument Manifolds Index General Purpose Manifolds Overview 1 2 Valve 2 3 Valve 4 5 Valve 6 Mounting kits 8
Instrument Manifolds Index General Purpose Manifolds Overview 1 2 Valve 2 3 Valve 4 5 Valve 6 Mounting kits 8 Special Application Manifolds Trifold 3 Valve 9 Rotofold 3 Valve 12 Pentafold 5 Valve 15 Mounting
Gauge Valves and Instrumentation Manifolds
Gauge Valves and ation Manifolds GV, GR Series 2-valve, 3-valve and 5-valve Manifold Series Nantong Naco Fluid Equipment Co.,LTD Pingchao Town, Tongzhou rea, Nantong City, jiangsu Province, China Tel:86-53-85400443
INTRODUCTION AND STANDARD SPECIFICATIONS
INTRODUCTION AND STANDARD SPECIFICATIONS INTRODUCTION Instrument valves and manifolds are often used on general applications for liquid and gas service and are suitable for shutting-off impulse lines to
Instrument Manifolds. V, VB, and VL Series. 2-, 3-, and 5-valve instrument manifolds
www.swagelok.com Manifolds V, VB, and VL Series 2-, 3-, and 5- instrument manifolds All 316 stainless steel construction with PTFE packing Working pressures up to 6000 psig (413 bar) Temperatures up to
P3M5S, P4M5S, P6M5S 5-VALVE SOFT SEAT MANIFOLD
P3M5S, P4M5S, P6M5S 5-VALVE MANIFOLD GAS STYLE MANIFOLD 5-Valve Gas Style Manifold The 5-valve manifold features 2 isolation valves, 2 equalizer valves and 1 vent valve in a single body for isolation and
needle valves Needle Valves
Needle Valves Index At a Glance 1 1700 Series 5 Forged Body, Integral Bonnet Needle Valves 2100 Series 8 Bar Stock, Screwed Bonnet Needle Valves 2200 Series 12 Bar Stock, Screwed Bonnet Needle Valves 2219
needle valves Needle Valves
Needle Valves Index At a Glance 1 1700 Series 5 Forged Body, Integral Bonnet Needle Valves 2100 Series 8 Bar Stock, Screwed Bonnet Needle Valves 2200 Series 12 Bar Stock, Screwed Bonnet Needle Valves 2219
3 & 5 VALVE DIFFERENTIAL MANIFOLDS Pressures to 10,000 psi (690 bar)
3 & 5 VALVE DIFFERENTIAL MANIFOLDS Quality Pascal Industries manufactures each component with the utmost care and attention. Materials are carefully selected to Pascal Industries proprietary standards
Hexagonal Bar Stock Needle Valve
Hexagonal Bar Stock Needle Valve HBNV Series Features Maximum working pressure: 6000 psi (414bar) at 100 F (38 C) 10000 psi (690bar) at 100 F (38 C) Working temperature: -65 F (-54 C) to 464 F (240 C)
Recognized globally for our quality, service and the ability to deliver! ISO 9001:
Recognized globally for our quality, service and the ability to deliver! ISO 9001:2008 www.mac-weld.com MACHINING LTD. CONTENTS Introduction Page 1-2 2 Valve Manifolds Page 3-4 3 Valve Manifolds Page 5-7
CONSTRUCTION MATERIAL 2 HOW TO ORDER 2 DESIGN FEATURES 3 PRODUCTS INDEX 4
Fluid control division MANIFOLD CONSTRUCTION MATERIAL 2 HOW TO ORDER 2 DESIGN FEATURES 3 INDEX 4 ACCESSORIES MOUNTING BRACKETS 35 OVAL FLANGES 35 BLEED 35 CONDENSING POTS 36 SYPHONS 36 AIR FEED HEADERS
VM Series Manifolds / Gauge Valves Manifolds- Direct & Remote Mount Gauge Valves Gauge Mount / Block & Bleed
VM Series Manifolds / Gauge Valves Manifolds- Direct & Remote Mount Gauge Valves Gauge Mount / Block & Bleed Catalog No. VM-3 July 2015 VMD Series Direct Mount Manifolds EN 61518: IEC 61518 standard is
)SLIM LINE) MONOFLANGE VALVES
)SLIM LINE) MONOFLANGE VALVES OVERVIEW The ASTAVA monoflange range is designed to seamlessly connect process piping to instrumentation. By offering a primary isolate bonnet, our line of monoflanges are
413 barg 38 C 200 barg 230 C psig 100 F 3000 psig 750 F
Model 101 Picture model: 101-06 Standard materials Body, Bonnet, Bellows (101-28) AISI 316 L Needle point Rotating ceramic ball Al 2O 3 Stem AISI 316 Ti with chromium-carbide diffusion coating Connections
The model M Valve Manifold is designed for direct mounting the manifold and transmitter together in a convenient and accessible location.
200 Series M-220 & M-222 2-Valve Manifolds The model M-220 2-Valve Manifold is designed for remote mounting of a static or gauge transmitter. This design permits the user to mount each unit separately
Instrument Manifold Systems
www.swagelok.com Instrument Manifold Systems Instrument, Direct, and Remote-Mount Manifolds and Modular Systems V, VB, and VL series 2-, 3-, and 5- instrument manifolds VE series 2-, 3-, and 5- direct-mount
Rosemount 1195 Integral Orifice Primary Element
September 2014 Rosemount DP Flow Rosemount 1195 Integral Orifice Primary Element Rosemount 1195 Integral Orifice Primary Element utilizes a self centering orifice plate design to eliminate installation
Type Pneumatic Control Valve Type 3525 Globe Valve
Type 355-1 Pneumatic Control Valve Type 355 Globe Valve Application Dump valve designed for use in high-pressure on/off applications in upstream oil and gas production. Valve size NPS 1 to 3 Pressure rating
TBV Instrumentation Valves
TBV Instrumentation Valves A TBV Instrumentation Valves Cameron s TBV instrumentation valves were developed in response to concerns expressed by plant engineers. Common problems such as irregular center-to-center
Hand & Gauge Isolation Valves Needle Valves Gauge Valves Block & Bleed Valves. Manifolds
Hand & Gauge Isolation Valves Needle Valves Gauge Valves Block & Bleed Valves Manifolds Two, Three & Five Valve Manifolds for Gauge and Differential Pressure Applications Accessories Built Hex tough for
Hand & Gauge Isolation Valves Needle Valves Gauge Valves Block & Bleed Valves. Manifolds
Hand & Gauge Isolation Valves Needle Valves Gauge Valves Block & Bleed Valves Manifolds Two, Three & Five Valve Manifolds for Gauge and Differential Pressure Applications Accessories Built Hex tough for
* Contact your sales representative for compliance to NACE MR or later requirements.
VALVES & CONTROLS crosby SERIES 00, 00 OMNI-TRIM, AND BP OMNI-TRIM Crosby s Series 00 adjustable blowdown, Series 00 fixed blowdown OMNI-TRIM, and BP OMNI-TRIM full nozzle pressure relief valves have a
General Specifications
General Specifications GS 22B01C06-01EN-A C13ST Manifolds for Traditional Mount Differential Pressure Transmitters Designed and manufactured by AS-Schneider, Yokogawa C13ST-3 and C13ST-5 manifolds are
T-Bar Bonnet. Monoflanges STANDARD OPTIONS. O.S.&Y. Bonnet (firesafe) Gas Solution Bonnet. Anti-Tamper Bonnet
T-Bar Bonnet Gas Solution bonnet with non-rotating Metal Stem Tip The Gas Solution bonnet protects the internal and external threads. Moreover, the bonnet thread is less subject to wear, since it is not
Spring loaded Thermal Relief Safety Valves, manufacturers standard Medium and high pressure
Series Thermal Relief Safety Valves Spring loaded Thermal Relief Safety Valves, manufacturers standard Medium and high pressure Applications The Sempell series provides a complete and comprehensive range
Gauge Valves and Instrumentation Manifolds
Gauge Valves and ation Manifolds GV, GVH, GR Series 2-valve, 3-valve and 5-valve Manifold Series FITOK Group FITOK GmbH (Headquarter) Sprendlinger Landstr. 5, 6369 Offenbach am Main, Germany Tel.: +49
Swing - Out Ball Valves. High Technology Valve & Fitting Series
Swing - Out Ball Valves High Technology Valve & Fitting SWB 30 SERIES SPECIFICATION Pressure Rating up to 000 psig (9 bar) at 00 (37 ) Temperature Range from -0 (- ) to 50 (3 ) TESTING Each valve is tested
Instrumentation Products Overview. Flow Control
Instrumentation Products Overview Flow Control World Leading Instrument Valve Solutions Century Valve is the number one choice for Instrument Valves and Manifolds; number one for range of products and
Rosemount Manifolds. Product Data Sheet April , Rev PC. Factory assembled, leak-tested, and calibrated
Product Data Sheet pril 2015 00813-0100-4733, Rev PC Rosemount Manifolds Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and in-line designs Integral
Needle Valves. Catalog 1203/1205 Aug 2012
Catalog 1203/1205 Aug 2012 Visual Index Click on link for desire page. At present image not available BAX-NVFF-01 FEMALE FEMALE Page 8 BAX-NVAMF-05 MALE FEMALE (ANGLE TYPE) Page 12 BAX-NVMFD-09 MALE -
HOKE Monoflange Valves. Primary Isolation Valves
HOKE Monoflange Valves Primary Isolation Valves Table of Contents Conventional Double Block & Bleed Assembly... 3 Applications, Specifications, Features & Benefits... 4 Features Cutaway... 5 HOKE Integral
Instrumentation Manifolds Traditional C13WT series. For DPharp EJX & EJA-E Differential Pressure and Pressure Transmitters
Instrumentation Manifolds Traditional C13WT series For DPharp EJX & EJA-E Differential Pressure and Pressure Transmitters Introduction About Yokogawa and WIKA About the catalogue Yokogawa and WIKA have
Manifold Valve Accessories
Accessories Manifold Valve Accessories DIELECTRIC KITS The dielectric kit is designed to maintain the integrity and reliability of the pipeline and piping system through safety and corrosion protection.
FORTUNE BRASS, CARBON, STAINLESS STEEL BALL VALVES
FORTUNE BRASS, CARBON, STAINLESS STEEL BALL VALVES FORGED BRASS BALL VALVES 2-pc Full Port Forged Brass Ball Valve, Packing Gland Design, 600 WOG/150 WSP, MSS-SP-110 CSA, UL, FM, NSF61 and LP Gass Approved
CROSBY J-SERIES DIRECT SPRING PRESSURE RELIEF VALVES
J-Series valves provide high quality and dependable overpressure protection for air, gas, steam, vapor, liquid and two-phase applications in one simple design FEATURES ASME/NB certified capacities for
One and Two-Piece Carbon Steel Flanged Ball Valves Illustrated Index
One and Two-Piece Carbon Steel Ball Valves Illustrated Index Unibody Carbon Steel Ball Valve ANSI Class 50 Unibody Carbon Steel Ball Valve ANSI Class 50 Unibody Design Detail Split-Body Design Detail Page
Dual Chamber Orifice Fitting
Dual Chamber Orifice Fitting Sure Shot Dual Chamber Orifice Fitting 1 11 2 3 10 4 9 8 5 7 6 1. Top Clamping Bar Gasket: Seals easily by tightening square head clamping bar screws. Non- Asbestos flat gasket
* Contact your sales representative for compliance to NACE MR or later requirements.
VALVES & CONTROLS crosby SERIES 800, 900 OMNI-TRIM, AND BP OMNI-TRIM Crosby s Series 800 adjustable blowdown, Series 900 fixed blowdown OMNI-TRIM, and BP OMNI-TRIM full nozzle pressure relief valves have
SUBSEA VALVES
SUBSEA VALVES Fitok Subsea Valves are manufactured with some notable differences to standard models to help ensure effective fluid transfer for the Oil and Gas Industry. Valves within the range include
High-Pressure Needle Valves
www.swagelok.com High-Pressure Needle Valves Working pressures up to 4 000 psig (3100 bar) Temperatures up to 40 F (232 C) Weep holes for leak detection Packing below stem threads Nonrotating stem design
Keystone WINN Hi-Seal High Performance Butterfly Valve
m o Keystone WINN Hi-Seal High Performance Butterfly Valve Hi-Seal, high performance butterfly valves offer efficient, bi-directional sealing across a wide spectrum of service conditions Features Positive
we are very grateful to our valuable customers who have shown a deep attention on to KpLÕ s growth and extended generous supports.
introduction we are very grateful to our valuable customers who have shown a deep attention on to KpLÕ s growth and extended generous supports. KpL valve ind. co., Ltd. was established in 1986 and for
Contents. General Arrangements 1 Horizontal Mounts 2 Vertical Mounts 3 Transmitter and Adapter Mounts
Contents General Arrangements 1 Horizontal Mounts 2 Vertical Mounts 3 Transmitter and Adapter Mounts Manifolds 4 Ordering Tree 5 Pressure vs. Temperature Ratings 6 5-Valve Manifold Overview 8 5-Valve Manifold
WKM 320F. Flanged floating ball valves
WKM 20F Flanged floating ball valves Contents WKM 20F Flanged Floating Ball Valves Features and benefits.................................................................... Exploded views and specifications....................................................5
General Specifications
General Specifications GS 22B01C05-00EN-A C13ST Manifolds for Traditional Mount Gauge and Absolute Pressure Transmitters Designed and manufactured by AS-Schneider, Yokogawa C13ST-2 2-Valve manifolds are
Instrument Manifold Valves
Instrument Manifold Valves eries 5000 Accurate flow measurement is of primary importance in achieving an efficient process system. Autoclave Engineers offers a complete line of needle, gauge and instrument
INSTRUMENTATION MANIFOLDS VALVES. VM Series.
INSTRUMENTATION MANIFOLDS VALVES VM Series www.unilok.com s - VM Series Features Pressure rating up to 6000psig (413bar) @38 C (100 F) Temperature rating from -53 C(-65 F) to 232 C (450 F) with standard
P R O C E S S V A L V E S. TBV Instrument Valves TBV
TBV Instrument Valves TBV TBV s Process / Instrument Valves were developed in response to concerns expressed by plant engineers. Common problems such as center-to-center spacing in Differential Pressure
Instrument Valves and Manifolds
Instrument Valves and Manifolds Needle Valves Instrument Valve Orifice Block Valves Gauge Block Valves Block & Bleed Valves Integral Block & Bleed Valves Two Valve Manifolds Three Valve Manifolds Five
INSTRUMENTATION MANIFOLDS VALVES. VM Series.
INSTRUMENTATION MANIFOLDS VALVES VM Series www.unilok.com s - VM Series Features Pressure rating up to 6000psig (413bar) @38 C (100 F) Temperature rating from -53 C(-65 F) to 232 C (450 F) with standard
Double Block and Bleed Manifolds and Flanged Products. Catalog 4190-FP October 2003
Double Block and Bleed Manifolds and Flanged Products Catalog 4190-FP October 2003 Contents Page 3 Introduction. Page 4/5 Application illustrations. Page 6 Ball valve specification. Page 7 Outside screw
ball valves ball valves 7 Series Fire Safe 2-way, 3-piece Bolted Ball Valves
7 Series Fire Safe 2-way, 3-piece Bolted Ball Valves HOKE s 7 Series Fire Safe Valves meet demanding application requirements in the production environment of chemical and petrochemical processing facilities.
I N N O VAT I V E I N N O VAT I V E S Y S T E M S & S O L U T I O N S B AT T E R Y C H A R G E R S TEC T HERMO E LECTRIC C HARGERS
DB1 DIFFERENTIAL PRESSURE B AT T E R Y C H A R G E R S The DB1 Differential Battery Charger uses the differential pressure developed across a pressure regulator to operate a small turbine generator which
PERFECTION IS OUR STANDARD...
PERFECTION IS OUR STANDARD... WELCOME TO COLSON X-CEL LTD Providing Precision engineering solutions for the most demanding environments Colson X-Cel Ltd is a well established and most highly respected
Crosby Series BP OMNI-TRIM Pressure Relief Valves for applications involving variable back pressure.
CROSBY Crosby Series BP OMNI-TRIM Pressure Relief Valves for applications involving variable back pressure. Features The balanced piston design offsets the effects of variable back pressure on valve set
Model DF100 Control Valve
FEATURES NACE Service Ready Standard construction for the DF100 control valve features NACE trim. The valve bonnet and body also conform to NACE MR0175 (National Association of Corrosion Engineers) recommendations.
Introduction. Application & Installation. Integral Block & Bleed Valves
Integral Block & Bleed Valves Introduction SUPERLOK's response to the demand for reduction in leakage paths has been the combination of primary and secondary valves into one compact unit. The combining
HANCOCK 600 GATE, GLOBE AND CHECK VALVES FORGED STEEL
HANCOCK 600 GATE, GLOBE AND CHECK VALVES A range of ASME class 800 and 1500 reduced bore forged steel valves with screwed, socket weld, butt weld or flanged ends GATE VALVES A compact but extremely sturdy
SVF FLOW CONTROLS. Series # Flanged Standard Port Fire Safe / API th Edition. Performance Engineered I N C O R P O R A T E D
Series 41 150# Flanged Standard Port Fire Safe / API-607 4 th Edition 1 PIECE REDUCED PORT BALL VALVE UNITS = INCHES SIZE CLASS 150 WEIGHTS L H W 1 1/2 11 6.50 3.86 9.06 2 21 7.01 4.65 9.06 3 40 7.99 5.98
VN Series Needle Valves
VN Series Needle Valves VN5, VN6, and VNS6 Series Regulating and Shut-Off Applications Catalog No. VN-2 January 2015 VN5 Series Integral-Bonnet Needle Valves VN6 Series Bar-Stock Needle Valves VNS6 & VNS10
Block & Bleed Valve.
Block & Bleed Valve www.nacoroke.com BLOCK & BLEED VALVES CONTENTS Introduction Application installaltions Specification Ball valve type OS&Y Needle type Glove Needle Valve type Block & Bleed valve Monoflange