Rosemount Manifolds. Product Data Sheet October , Rev PB. Factory assembled, leak-tested, and calibrated

Transcription

1 Product Data Sheet October , Rev PB Rosemount Manifolds Factory assembled, leak-tested, and calibrated Full breadth of offering including integral, conventional, and in-line designs Integral design enables flangeless valve integration 2, 3, and 5-valve configurations Compact, lightweight design Easy in-process calibration Direct-mount capability

2 Rosemount Manifolds October 2014 Rosemount Manifolds Selection Guide Rosemount 305 Integral Manifold See Options on page 28. Assembles directly to transmitter, eliminating need for flange 2, 3, and 5-valve configuration Available in Coplanar and traditional styles Compact, lightweight assembly Factory assembled, seal-tested, and calibrated Rosemount 304 Conventional Manifold See Options on page 28. Attaches to transmitter flange 2, 3, and 5-valve configurations Traditional (Flange x Flange, Flange x NPT) & Wafer styles Factory assembled, seal-tested, and calibrated 50% fewer leak points than conventional transmitter/flange/manifold interface Rosemount 305 Integral Manifold- Coplanar Style Rosemount 306 In-Line Manifold Rosemount 304 Conventional Manifold-Traditional Style See Options on page 28. Assembled directly to in-line pressure transmitters Block-and-Bleed and 2-valve configurations Male or female threaded NPT process connection Rosemount 304 Conventional Manifold-Wafer Style Rosemount 306 In-Line Manifold Contents Valve Configuration Ordering Information Specifications Dimensional Drawings

3 October 2014 Rosemount Manifolds Valve Configuration Block-and-bleed The block-and-bleed configuration is available on the Rosemount 306 Manifold for use with in-line gage and absolute pressure transmitters. A single block valve provides instrument isolation and a plug provides drain/vent capabilities. 306 Manifold Transmitter Three-valve The three-valve configuration is available on Rosemount 305 and 304 Manifolds for use with differential pressure and multi-variable transmitters. Two block valves provide instrument isolation, and one equalize valve is positioned between the high and low transmitter process connections. 305 Manifold Bleed Screw Transmitter Drain/Vent Drain/Vent Isolate Equalize Process Isolate Process Isolate Two-valve The two-valve configuration is available on Rosemount 305, 306, and 304 Manifolds for use with absolute and gage pressure transmitters. A block valve provides instrument isolation and a drain/vent valve allows venting, draining, or calibration. 305 & 306 Manifolds Isolate Transmitter Test/Vent 304 (Traditional) Manifold Transmitter Equalize Isolate Process 304 (Wafer) Manifold Transmitter Isolate Test (Plugged) 304 Manifold Process Transmitter Isolate Equalize Isolate Test (Plugged) Test/Vent Process Isolate Process Note Test/vents receive plastic caps to protect threaded connections unless otherwise noted. Note Test (plugged) connections receive 1 /4-in. NPT plugs unless otherwise noted. 3

4 Rosemount Manifolds October 2014 Five-valve The five-valve configuration is available on Rosemount 305 and 304 Manifolds for use with differential pressure and multi-variable transmitters. Two block valves provide instrument isolation and one equalize valve is positioned between the high and low transmitter process connections. In addition, two drain/vent valves allow for controlled venting, 100% capture of vented or drained process, and simplified in-process calibration capability. 305 Manifolds & 304 (Wafer) Transmitter Five-valve natural gas The five-valve natural gas configuration is available on the Rosemount 305 and 304 Manifolds for use with differential pressure and multi-variable transmitters. Two block valves provide instrument isolation and a single drain/vent valve allows for controlled venting, 100% capture of vented or drained process, and simplified in-process calibration capability. In addition, two equalize valves provide extra protection from leaking to ensure DP signal integrity. 305 Manifolds & 304 (Traditional) Transmitter Test/ Vent Equalize Test/ Vent Test (Plugged) Equalize Equalize Test (Plugged) Isolate Isolate Isolate Isolate Process Process Drain/Vent Process Note Test/vents receive plastic caps to protect threaded connections unless otherwise noted. Note Test (plugged) connections receive 1 /4-in. NPT plugs unless otherwise noted. 4

5 October 2014 Rosemount Manifolds Ordering Information Rosemount Manifolds can be ordered as a stand-alone product or as an integrated assembly that is attached to a transmitter. Stand-alone manifold 1. Reference the Rosemount Manifolds Selection Guide (see page 2) for assistance on choosing the type of manifold needed. 2. Specify a completed model number by referencing the applicable ordering table for the selected manifold type: a. Rosemount 305 Integral Manifold, see page 6. b. Rosemount 306 In-Line Manifold, see page 13. c. Rosemount 304 Conventional Manifold, see page 10. Transmitter/manifold assembly 1. Specify a completed Rosemount transmitter model number by referencing the applicable product data sheet. 2. Specify a completed manifold model number by referencing the applicable ordering table for the selected manifold type: a. Rosemount 305 Integral Manifold, see page 6. b. Rosemount 306 In-Line Manifold, see page 13 c. Rosemount 304 Conventional Manifold, see page Verify the transmitter model number contains the correct Process Connection code or Manifold Option code for the desired transmitter manifold assembly (see Table 1). Table 1. Ordering Codes for a Transmitter/Manifold Assembly Transmitter Manifold Process connection code Manifold option code 305 A11 N/A 3051S 3051/ A11 N/A 304 A12 N/A 305 N/A S5 306 N/A S5 304 N/A S6 305 N/A N/A 306 N/A S5 304 N/A N/A 5

6 Rosemount Manifolds October 2014 Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See page 12 for more information on Material Selection. Table 2. Rosemount 305 Integral Manifold Ordering Information The Standard offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Model Product description 0305 Integral Manifold Manufacturer R Rosemount Manifold style C Coplanar T Traditional M Traditional (DIN-compliant flange) Manifold type 2 2-valve 3 3-valve 5 (1) 5-valve 6 (2) 5-valve Natural Gas Metering Pattern 7 (2)(3) 2-valve (per ASME B31.1 [ANSI] Power and Piping Code) 8 (2)(3) 3-valve (per ASME B31.1 [ANSI] Power and Piping Code) 9 (2)(3) 5-valve (per ASME B31.1 [ANSI] Power and Piping Code) Body Bonnet Stem and tip/ball SST 316 SST 316 SST 3 (4) Alloy C-276 Alloy C-276 Alloy C Alloy 400 Alloy 400 Alloy 400/K-500 Process connection style A (5) 1 /4 18 NPT female B (6) 1 /2 14 NPT female Packing material 1 PTFE 2 (7) Graphite-based Valve seat 1 Integral 5 Soft delrin (only available with natural gas metering pattern) Options Extended product warranty WR3 3-year limited warranty WR5 5-year limited warranty 6

7 October 2014 Rosemount Manifolds Table 2. Rosemount 305 Integral Manifold Ordering Information The Standard offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Mounting brackets B1 Bracket for 2-in. pipe mounting, CS bolts B3 (8) Flat bracket for 2-in. pipe mounting, CS bolts B4 SST Mounting Bracket for 2-in. pipe mounting, 300 SST bolts B7 B1 bracket with 316 SST bolts B9 (8) B3 bracket with 316 SST bolts BA 316 SST B1 bracket with 316 SST bolts BC (8) 316 SST B3 bracket with 316 SST bolts BE 316 SST B4 bracket with 316 SST bolts Bolt materials L4 (9) Austenitic 316 SST bolts L5 ASTM A193, Grade B7M bolts L8 ASTM A193, Class 2, Grade B8M bolts Cleanings P2 (10) Cleaning for special services Material recommendations for NACE SG (4)(11) Sour Gas (meets NACE MR 0175 / ISO 15156, MR 0103) Adapters DF (12) 1 /2-14 NPT female flange adapter DQ (12) 12 mm ferrule tube flange adapter Process flange bolting connection HK (13) 10 mm (M10) process flange bolting connection HL (13) 12 mm (M12) process flange bolting connection Typical coplanar integral manifold model number: 305RC32B11B4 (1) Not available with traditional manifold style T. (2) Only available with Coplanar manifold style code C. (3) Only available with 316 SST materials of construction code 2 and graphite based backing code 2. (4) Materials of Construction comply with recommendations per NACE MR 0175/ISO for sour oil field production environments. Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments. (5) Only available with traditional manifold style codes T and M. (6) Not available with traditional manifold style code M. (7) Includes graphite tape on drain/vent valves and plugs. (8) Not compatible with the Rosemount 3095 transmitter. (9) Not available with ASME B31.1 manifold type codes 7, 8, and 9. (10) Not available with Graphite-Based Packing Material code 2. (11) Only available with 316 SST Materials of Construction Code 2: 316 SST body and bonnets; Alloy C-276 stems, tip/balls, and drain/vents. (12) Only allowed with Manifold Style code T. Not allowed with Graphite-Based Packing code 2. (13) Only available with traditional manifold style code M. 7

8 Rosemount Manifolds October 2014 Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See page 12 for more information on Material Selection. Table 3. Rosemount 306 Pressure Manifold Ordering Information The Standard offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Model Product description 0306 Pressure Manifold Manufacturer R Rosemount Inc. Manifold style T Threaded Manifold type 1 Block and bleed 2 2-valve 3 (1) 2-valve (per ASME B31.1 Power Piping Code) Body Bonnet Stem and tip/ball SST 316 SST 316 SST 3 (2)(3) Alloy C-276 Alloy C-276 Alloy C-276 Process connection AA 1 /2 14 male NPT BA (2) 1 /2 14 female NPT Packing material 1 PTFE 2 (4) Graphite-based Valve seat 1 Integral Options Extended product warranty WR3 3-year limited warranty WR5 5-year limited warranty Cleanings P2 (5) Cleaning for special services Material recommendations for NACE SG (3)(6) Sour Gas (meets NACE MR 0175 / ISO 15156, MR 0103) Typical integral manifold model number: 306RT22BA11 (1) Only available with 316 SST materials of construction and graphite-based packing. (2) Not available with block-and-bleed manifold type 8

9 October 2014 Rosemount Manifolds (3) Materials of Construction comply with recommendations per NACE MR0175/ISO for sour oil field production environments. Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments. (4) Includes graphite tape on plugs. (5) Not available with Graphite-Based Packing Material code 2. (6) Only available with 316 SST material of construction code 2. Manifolds with SG option are built with 316 SST body and bonnets; Alloy C-276 stems, tips/balls. 9

10 Rosemount Manifolds October 2014 Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See page 12 for more information on Material Selection. Table 4. Rosemount 304 Conventional Manifold Ordering Information The Standard offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Model Product description 0304 Conventional Manifold Manufacturer R Rosemount Manifold style T Traditional (Flange x Flange or Flange x NPT) W (1) Wafer Manifold type 2 (2) 2-valve 3 3-valve 5 (3) 5-valve 6 (2) 5-valve Natural Gas Metering Pattern 7 (2)(4) 2-valve (per ASME B31.1 [ANSI] Power and Piping Code) 8 (2)(4) 3-valve (per ASME B31.1 [ANSI] Power and Piping Code) Body Bonnet Stem Tip SST 316 SST 316 SST 316 SST 5 CS 316 SST 316 SST 316 SST Process connection style B 1 /2-14 NPT F (2) Flanged Packing material 1 PTFE 2 (1) Graphite-based Bolts 1 For assembly to 2051/3051 Traditional Flange 2 For assembly to 2051/3051 DIN Compliant Traditional Flange 3 For assembly to 2051/3051 Coplanar Flange 10

11 October 2014 Rosemount Manifolds Table 4. Rosemount 304 Conventional Manifold Ordering Information The Standard offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Options Extended product warranty WR3 3-year limited warranty WR5 5-year limited warranty Mounting brackets VC (2) Manifold Heavy Duty Mounting Bracket, CS for Traditional Style VS (2) Manifold Heavy Duty Mounting Bracket, 316 SST for Traditional Style B4 (3) Manifold SST Mounting Bracket for 2-in. pipe mount with series 300 SST bolts for wafer style Adapters DF (5) 1 /2-14 NPT Female Flange Adapter DT (5) 1 /2-in. ferrule tube flange adapter DQ (5) 12 mm ferrule tube flange adapter Bolt material L4 (6) Austenitic 316 SST Bolts L5 ASTM A193, Grade B7M Bolts L8 ASTM A193, Class 2, Grade B8M Bolts Material recommendations for NACE SG (1)(7) Sour Gas meets NACE MR 0175 / ISO 15156, MR 0103) Cleanings P2 (8) Cleaning for special service Heater block kits SB (9) Steam block kit, ¼-in. NPT connection Typical model number: 0304RT32B11VS (1) Only allowed with Material of Construction code 2. (2) Not available with Wafer Manifold Style code W. (3) Not available with Traditional Manifold Style code T. (4) Only available with 316 SST materials of construction code 2 and graphite based packing code 2. (5) Only allowed with both Manifold Style code T and Process Connection code F. Not allowed with Graphite-based Packing Code 2. (6) Not available with Manifold Type codes 7, 8. (7) Materials of construction comply with recommendations per NACE MR 0175 / ISO 1516 for sour oil field production environments. Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR 0103 for sour refining environments. (8) Not available with Graphite-Based Packing Material code 2. (9) Not available with Manifold Type code 6. 11

12 Rosemount Manifolds October 2014 Specifications Material selection Emerson provides a variety of Rosemount product with various product options and configurations including materials of construction that can be expected to perform well in a wide range of applications. The Rosemount product information presented is intended as a guide for the purchaser to make an appropriate selection for the application. It is the purchaser s sole responsibility to make a careful analysis of all process parameters (such as all chemical components, temperature, pressure, flow rate, abrasives, contaminants, etc.), when specifying product, materials, options and components for the particular application. Emerson Process Management is not in a position to evaluate or guarantee the compatibility of the process fluid or other process parameters with the product, options, configuration or materials of construction selected. Pressure and temperature ratings Figure 1. Rosemount 305 Integral Manifolds - Pressure vs. Temperature PTFE Packed, Soft Delrin Seat PTFE Packed, Integral Seat Graphite Packed, Integral Seat Graphite Packed, (ASME B31.1), Integral Seat 6000 (414) Pressure psig (bar) 5000 (345) 4000 (276) 3000 (207) 2000 (138) 1000 (69) 0 0 (-18) 100 (38) 200 (93) 300 (149) 400 (204) 500 (260) 600 (316) 700 (371) 800 (427) 900 (482) 1000 (538) Temperature F ( C) Table 5. Rosemount 305 Integral Manifolds - Pressure and Temperature Ratings (1) Packing (1) Seat Pressure and temperature ratings PTFE Integral F ( C) F ( C) PTFE Soft Delrin F ( C) Graphite Graphite (ASME B31.1) Integral Integral F ( C) F ( C) F ( C) F ( C) (1) Except option HK: PTFE, Integral seat: F ( C), F ( C) Graphite, Integral seat: F ( C), F ( C) 12

13 October 2014 Rosemount Manifolds Figure 2. Rosemount 306 In-Line Manifolds - Pressure vs. Temperature PTFE Packed, Integral Seat Graphite Packed, Integral Seat Graphite Packed, (ASME B31.1), Integral Seat (689) Pressure psig (bar) 8000 (552) 6000 (414) 4000 (276) 2000 (138) 0 0 (-18) 100 (38) 200 (93) 300 (149) 400 (204) 500 (260) 600 (316) 700 (371) 800 (427) 900 (482) 1000 (538) Temperature F ( C) Table 6. Rosemount 306 In-Line Manifolds - Pressure and Temperature Ratings Packing Seat Pressure and temperature ratings PTFE Graphite Graphite (ASME B31.1) Integral Integral Integral F ( C) F ( C) F ( C) F ( C) F ( C) F ( C) 13

14 Rosemount Manifolds October 2014 Figure 3. Rosemount 304 Conventional Manifolds PTFE Packed, Integral Seat Graphite Packed - Wafer, Integral Seat Graphite Packed - Flanged (SST), Integral Seat Graphite Packed - Flanged (CS), Integral Seat Graphite Packed (ASME B31.1), Integral Seat 6000 (414) 5000 (345) Pressure psig (bar) 4000 (276) 3000 (207) 2000 (138) 1000 (69) 0 0 (-18) 100 (38) 200 (93) 300 (149) 400 (204) 500 (260) 600 (316) 700 (371) 800 (427) 900 (482) 1000 (538) Temperature F ( C) Table Conventional Manifolds - Pressure and Temperature Ratings Packing Seat Pressure and temperature ratings PTFE Graphite - Wafer Graphite - Flanged (SST) Graphite - Flanged (CS) Graphite (ASME B31.1) Integral Integral Integral Integral Integral F ( C) F ( C) F ( C) F ( C) F ( C) F ( C) F ( C) F ( C) F ( C) F ( C) 14

15 October 2014 Rosemount Manifolds Process connections Table 8. Process Connections Model and style Connection Rosemount 305 Integral Manifold Coplanar Traditional 1 /2-14 Female NPT 1 /4-18 Female NPT (Process Adapters optional) Optional Process Adapters 1 /2-14 Female NPT Flange Adapter 12 mm Ferrule Tube Flange Adapter Rosemount 306 In-Line Manifold Block-and-Bleed 2-Valve Rosemount 304 Conventional Manifold Flange by Pipe Flange by Flange Wafer 1 /2-14 Male NPT 1 /2-14 NPT (Male or Female) 1 /2-14 Female NPT 2 1 /8-in. (54 mm) center-to-center connection (Process Adapters required) 1 /2-14 Female NPT Process Adapters 1 /2-14 Female NPT Flange Adapter 1 /2-in. Ferrule Tube Flange Adapter 12-mm Ferrule Tube Flange Adapter Instrument connections Table 9. Manifold - Transmitter Interface Model Rosemount 305 Integral Manifold Rosemount 306 In-Line Manifold Rosemount 304 Conventional Manifold Connection Mounted directly to Coplanar sensor module of transmitter, 1.3-in. (287 mm) center-to-center process isolators 1 /2-14 Male NPT Mounted to traditional transmitter flange, 2 1 /8-in. (54 mm) center-to-center connection per IEC 61518, Type B shut-off device (without SPIGOT) Test/vent connections 1 /4-18 Female NPT Manifold bolts Standard material is plated carbon steel per ASTM A449, Type 1 Alternative bolt materials offered through Option Codes L4 for Austenitic 316 Stainless Steel Bolts L5 for ASTM A193, Grade B7M Bolts L8 for ASTM A193, Class 2, Grade B8M Bolts 15

16 Rosemount Manifolds October 2014 O-rings Figure 4. Rosemount 305 Integral Manifold O-rings Sensor Module-to-Manifold O-rings Specified in the transmitter model number Figure 5. Rosemount 304 Conventional Manifold O-rings Manifold-to-Flange O-rings Same material as specified by manifold Packing Material selection (1) Flange Adapter O-rings Glass-filled PTFE (1) Available in Packing Material code 1 (PTFE) or code 2 (Graphite). 16

17 October 2014 Rosemount Manifolds Table 10. Rosemount 305 Integral Manifolds - Process Wetted Materials of Construction Component SST Alloy C SST with SG option Body 316 SST Alloy C SST Ball/Tip 316 SST /316Ti SST Alloy C-276 Alloy C-276 Stem 316 SST Alloy C-276 Alloy C-276 Packing PTFE/Graphite PTFE/Graphite PTFE/Graphite Bonnet 316 SST Alloy C SST Pipe Plug 316 SST Alloy C SST Drain/Vent Valve 316 SST Alloy C-276 Alloy C-276 Table 11. Rosemount 306 In-line Manifolds - Process Wetted Materials of Construction Component SST Alloy C SST with SG option Body 316 SST Alloy C SST Ball/Tip 316 SST /316Ti SST Alloy C-276 Alloy C-276 Stem 316 SST Alloy C-276 Alloy C-276 Packing PTFE/Graphite PTFE/Graphite PTFE/Graphite Bonnet 316 SST Alloy C SST Pipe Plug 316 SST Alloy C SST Bleed Screw 316 SST / 316Ti SST Alloy C-276 Alloy C-276 Table 12. Rosemount 304 Conventional Manifolds - Process Wetted Materials of Construction Component SST CS SST with SG option Body 316 SST CS 316 SST Ball/Tip 316 SST/316Ti SST 316 SST Alloy C-276 Stem 316 SST 316 SST Alloy C-276 Packing PTFE/Graphite PTFE PTFE/Graphite Bonnet 316 SST 316 SST 316 SST Pipe Plug 316 SST CS 316 SST 17

18 Rosemount Manifolds October 2014 Materials of construction - typical Figure 6. Typical Rosemount Manifold Valve A B E C A. Bonnet B. Stem C. Packing D. Ball/Tip E. Body D Estimated weight Model and description Weight Rosemount 305 Integral Manifold Rosemount 306 In-Line Manifold 2-valve coplanar 2-valve traditional 3-valve coplanar 3-valve traditional 5-valve coplanar Block-and-Bleed 2-valve Rosemount 304 Conventional Manifold 2-valve traditional flange x NPT 2-valve traditional flange x flange 3-valve traditional flange x NPT 3-valve traditional flange x flange 3-valve wafer flange x NPT 5-valve wafer flange x NPT 5-valve traditional flange x NPT 5-valve traditional flange x flange 4.5 lbs (2.0 kg) 6.0 lbs (2.7 kg) 4.7 lbs (2.1 kg) 6.0 lbs (2.7 kg) 6.5 lbs (3.0 kg) 1.1 lbs (0.5 kg) 2.5 lbs (1.1 kg) 5.0 lbs (2.3 kg) 5.5 lbs (2.5 kg) 5.2 lbs (2.4 kg) 5.7 lbs (2.6 kg) 4.0 lbs (1.8 kg) 5.7 lbs (2.6 kg) 5.7 lbs (2.6 kg) 5.7 lbs (2.6 kg) 18

19 October 2014 Rosemount Manifolds Dimensional Drawings Rosemount 305 Manifold Rosemount 305R Two-Valve Coplanar Style Manifold 5.21 (132) 4.20 (107) 4.55 (116) 8.95 (228) 7.70 (196) 4.30 (109) 7.2 (183) 1 /2-14 NPT on Manifold for Process Connection 1 /4-18 NPT for test/vent connection. Rosemount 305R Three-Valve Coplanar Style Manifolds 5.21 (132) 4.20 (107) 4.55 (116) 8.95 (228) 7.70 (196) Drain/Vent Valve 5.00 (127) 9.20 (234) 1 /2-14 NPT on Manifold for Process Connections, inch center-to-center 19

20 Rosemount Manifolds October 2014 Rosemount 305R Five-Valve Coplanar Style Manifold 5.21 (132) 4.20 (107) 4.55 (116) 8.95 (228) 7.70 (196) 5.00 (127) (269) 1 /2-14 NPT on Manifold for Process Connections, inch center-to-center 1 /4-18 NPT for test/vent connection. Rosemount 305RT Two-Valve Traditional Style Manifold 5.21 (132) 4.20 (107) 4.55 (116) 7.70 (196) 1 /2-14 NPT on optional Process Adapter 1.63 (41) 3.75 (95) 3.50 (89) 1 /4-18 NPT on traditional manifold for process connection without the use of a process adapter 1.10 (28) (54) 6.40 (163) 20

21 October 2014 Rosemount Manifolds Rosemount 305RT Three-Valve Traditional Style Manifold 5.21 (132) 4.20 (107) 4.55 (116) 7.70 (196) 1 /2-14 NPT on optional Process Adapter (1) Drain/Vent Valve 1.63 (41) 3.75 (95) 1.05 (27) 3.5 (87) 1.10 (28) 1 /4-18 NPT on traditional manifold for process connections without the use of process adapters (54) 6.40 (163) 8.90 (226) 2.70 (69) Max Open (1) Adapters can be rotated to give adapter connection centers of 2.0 (51), (54), or 2.25 (57). Rosemount 305RM Two-Valve Traditional Style Manifold 5.21 (132) 4.20 (107) 4.55 (116) 7.70 (196) 1 /2-14 NPT on optional Process Adapter 1.63 (41) 4.20 (107) 1 /4-18 NPT on traditional manifold for process connection without the use of a process adapter (54) 1 /4-18 NPT Vent Connection 4.13 (105) 1.10 (28) 6.5 (165) 21

22 Rosemount Manifolds October 2014 Rosemount 305RM Three-Valve Traditional Style Manifold 5.21 (132) 4.20 (107) 4.55 (116) 0.75 (19) Clearance for Cover Removal 7.70 (196) Drain/Vent Valve 1 /2-14 NPT on optional Process Adapter (1) 1.63 (41) 4.20 (107) 1 /4-18 NPT on traditional manifold for process connections without the use of process adapters 1.05 (27) 4.13 (105) 1.10 (28) (54) 6.5 (165) 9.02 (230) 2.5 (63) Max Open (1) Adapters can be rotated to give adapter connection centers of 2.0 (51), (54), or 2.25 (57). Rosemount 305RM Five-Valve Traditional Style Manifold 4.20 (107) 5.21 (132) 4.55 (116) 7.70 (196) 1 /2-14 NPT on optional Process Adapter (1) 1.63 (41) 4.2 (107) 2.6 (66) 4.13 (105) 1 /4-18 NPT on traditional manifold for process connections without the use of process adapters (28) (54) 6.5 (165) 9.02 (230) 2.5 (63) Max Open (1) Adapters can be rotated to give adapter connection centers of 2.0 (51), (54), or 2.25 (57). 22

23 October 2014 Rosemount Manifolds Rosemount 306 Manifold Rosemount 306R Pressure Style Manifold (3051S_T Shown) BLOCK AND BLEED STYLE TWO-VALVE STYLE 4.20 (107) 4.55 (116) 8.00 (203) 1 /4-18 NPT on traditional vent connection (pipe plug shown) 4.85 (123) Bleed Screw 4.40 (112) 3.75 (96) Manifold valve orientation may vary with respect to transmitter mounting holes. 1 /2-14 NPT Female NPT Process Connection (code BA) Traditional Manifold with Optional Brackets for 2-in. Pipe Mounting 8.18 (208) 3.56 (90) 1.1 (28) (86.9) (89) B3/B9/BC MOUNTING BRACKET 2.62 (66) 7.7 (196) 1.94 (49.2) (331) 0.93 (24) B1/B7/BA MOUNTING BRACKET 5.32 (135) 3.50 (89) 3.56 (90) 4.85 (123) 1.1 (28) 23

24 Rosemount Manifolds October 2014 Coplanar Manifold with Optional Bracket for 2-in. Pipe Mounting 7.68 (195) OPTION CODE B4 2-in. U-Bolt for Pipe Mounting 4.9 (125) 3.54 (90) 6.25 (159) VS/VC Heavy Duty Manifold Mounting Bracket 2-IN. PIPE MOUNT Drain/Vent Valve 1.05 (26.67) PANEL MOUNT 2.93 (74) 4.20 (107) 3.46 (88) 3.75 (95) 2-in. Pipe 5.88 (145) 3.50 (89) Max Open 5.88 (149) 2.75 (70) 24

25 October 2014 Rosemount Manifolds Rosemount 304 Manifold Rosemount 304 Two-Valve Flange X NPT Conventional Manifold φ0.281 Mounting Holes (2) INSTRUMENT SIDE 2.12 (54) 1 /4 NPT Test 1 /4 NPT Test 3.75 (95) 5.78 (147) 1.13 (29) PROCESS SIDE 3.50 (89) 1 /2 NPT Process Connection on (54) Centers (2) Rosemount 304 Two-Valve Flange X Flange Conventional Manifold φ0.281 Mounting Holes (2) 1 /4 NPT Test INSTRUMENT SIDE 2.12 (54) 1 /4 NPT Test 3.75 (95) 1.13 (29) 5.78 (147) PROCESS SIDE 3.50 (89) 7 /16 20 UNF Mounting Holes (4) on a x in. Hole Pattern 25

26 Rosemount Manifolds October 2014 φ0.281 Mounting Holes (2) 1 /4 NPT Test (2) Rosemount 304 Three-Valve Flange X NPT Conventional Manifold INSTRUMENT SIDE 2.12 (54) 3.75 (95) 1.13 (29) 8.18 (208) PROCESS SIDE 3.50 (89) 1 /2 NPT Process Connection on (54) Centers (2) Rosemount 304 Three-Valve Flange X Flange Conventional Manifold φ0.281 Mounting Holes (2) 1 /4 NPT Test (2) INSTRUMENT SIDE 2.12 (54) 3.75 (95) PROCESS SIDE 1.13 (29) 8.18 (208) 3.50 (89) 7 /16 20 UNF Mounting Holes (4) on a x in. Hole Pattern 26

27 October 2014 Rosemount Manifolds Rosemount 304 Natural Gas Five-Valve Flange X NPT Conventional Manifold INSTRUMENT SIDE 2.12 φ0.281 Mounting (54) Holes (2) 1 /4 NPT Test (2) 3.75 (95) 1.13 (29) 8.18 (208) PROCESS SIDE 1 /4 NPT Vent 3.5 (89) Max Open 1 /2 NPT Process Connection on (54) Centers (2) Rosemount 304 Natural Gas Five-Valve Flange X Flange Conventional Manifold INSTRUMENT SIDE 2.12 φ0.281 Mounting (54) Holes (2) 1 /4 NPT Test (2) 3.75 (95) 1 /4 NPT Vent 1.13 (29) 8.18 (208) PROCESS SIDE 3.5 (89) 7 /16 20 UNF Mounting Holes (4) on a x in. Hole Pattern Rosemount 304 Three-Valve Wafer Manifold INSTRUMENT SIDE 9.13 (232) 4.88 (124) 1 /2 14 NPT Process Connection (2) 1.25 (32) PROCESS SIDE 3 /8 16 UNC Mounting Holes (2) 1.50 (38) 3.35 (85) 27

28 Rosemount Manifolds October 2014 Options Module guard A sensor module guard is available to protect the transmitter process isolating diaphragms. This guard should be used whenever the transmitter is removed from the integral manifold to avoid damage to the isolating diaphragms. Part number: (5/pack) ASME B31.1 power piping code Rosemount Manifolds are available in configurations that meet the requirements of the ASME B31.1 Power Piping Code. This code specifies design criteria for most air, gas, steam, water, and oil systems used in electric generating systems, central and district heating systems, industrial power plants, and geothermal plants. ASME B31.1 includes requirements for manifolds, valves, and piping. Transmitters and other measuring devices do not fall within the scope of this code. Marking Manifolds are tagged with a part number, schematic drawing, temperature, and pressure limits. Other publications P2 cleaning for special services For additional information, go to. Per ASTM G93-96, this option minimizes process contaminants by cleaning wetted surfaces with a suitable detergent. SG sour gas Materials of Construction comply with recommendations per NACE MR 0175/ISO for sour oil field production environments. Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments. Heat block kits Rosemount 304 Manifolds are available with steam heat block kits for cold environments and services. The steam block attaches directly to the manifold to prevent the process from freezing. 28

29 October 2014 Rosemount Manifolds Spare parts list Table 13. Rosemount 305 Integral Manifold Part description Part number (traditional style) Part number (coplanar style) Mounting brackets (qty. 1) Manifold SST Mounting Bracket for 2-in Pipe Mount N/A Bolt kits (set of 4) CS Bolt Kit SST Bolt Kit ANSI/ASTM-A-193-B7M Bolt Kit Drain/vents (qty. 1) 316 SST Drain/Vent for use with 3-valve 305 Manifold Alloy C-276 Drain/Vent for use with 3-valve 305 Manifold Coplanar flange kits (qty. 1) Differential Flange Kit, SST N/A Gauge Flange Kit, SST N/A O-rings (set of 12) Manifold-to-Module O-ring, Glass-filled PTFE Manifold-to-Module O-ring, Graphite-filled PTFE Sensor guard (set of 5) Coplanar Module Sensor Guard

30 Rosemount Manifolds October 2014 Table 14. Rosemount 304 Conventional Manifold Part description Part number (traditional style) Part number (wafer style) Mounting brackets (qty. 1) Manifold Heavy Duty Mounting Bracket, CS N/A Manifold Heavy Duty Mounting Bracket, 316 SST N/A Manifold SST Mounting Bracket for 2-in. Pipe Mount N/A O-rings (set of 12) Manifold-to-Flange O-ring, Virgin PTFE Manifold-to-Flange O-ring, Graphite Manifold-to-flange bolt kits (set of 4) Consult factory for part numbers Consult factory Consult factory Heater block kits (qty. 1) Steam Block Kit (1) N/A Socket weld adapter kit (qty. 2) Virgin PTFE O-rings, Carbon Steel Bolts, 316L SST adapter N/A Virgin PTFE O-rings, 316 SST Bolts, 316L SST adapter N/A Graphite O-rings, Carbon Steel Bolts, 316L SST adapter N/A Graphite O-rings, 316 SST Bolts, 316L SST adapter N/A (1) Not available with Manifold Type code 6. 30

31 October 2014 Rosemount Manifolds 31

32 Rosemount Manifolds , Rev PB Product Data Sheet October 2014 Emerson Process Management Rosemount Inc Market Boulevard Chanhassen, MN USA T (U.S.) T (International) (952) F (952) Emerson Process Management Blegistrasse 23 P.O. Box 1046 CH 6341 Baar Switzerland T +41 (0) F +41 (0) Emerson Process Management Asia Pacific Pte Ltd 1 Pandan Crescent Signapore T F Service Support Hotline: Enquiries@AP.EmersonProcess.com Emerson Process Management Latin America 1300 Concord Terrace, Suite 400 Sunrise, Florida USA T Standard Terms and Conditions of Sale can be found at \terms_of_sale. The Emerson logo is a trade mark and service mark of Emerson Electric Co. Coplanar, Rosemount, and the Rosemount logotype are registered trademarks of Rosemount Inc. All other marks are the property of their respective owners Rosemount Inc. All rights reserved.