Instrument Manifold Valves

Transcription

1 Instrument Manifold Valves eries 5000 Accurate flow measurement is of primary importance in achieving an efficient process system. Autoclave Engineers offers a complete line of needle, gauge and instrument manifold valves designed to provide accurate, safe and dependable flow measurement. Manufactured for Autoclave Engineers, the design of these valves reflects extensive engineering and manufacturing experience, resulting in attainment of the highest standards for valve quality and reliability. AE eries 5000 needle, gauge and instrument manifold valves have been engineered to provide versatility in meeting specific process requirements. everal standard bonnet assemblies offer different stem, seal and material selections. s are installed in hard seat, soft seat and roddable valve models of varied body designs to accommodate the process control, flow measurement and mounting requirements of specific applications. Most valves are rated for pressure service to 6,000 psi (414 bar) with certain models rated to 10,000 psi (690 bar). : One piece bar stock construction with full material traceability. Back seating of stems in a fully open position prevents stem backout. Permanent locking of valve bonnet prevents accidental removal while operating valve. tem seal isolates the lubricated stem threads from the process. tainless models of needle, gauge and instrument manifold valves, equipped with needle stems, meet NAE MR Optional high temperature packing for compatibility to 1000 F (538 ) on certain models. All valves are designed in accordance with AME/ANI B and AME ection VIII, Div. 1. All general terms and conditions of sale, including limitations of our liability, apply all products and services sold. Instrument Manifold Valves - eries 5000

2 Instrument Manifold Valves - General Information Needle Valves - Gauge Valve - Instrument Manifold Valves - ustomer upport Needle Valves Autoclave needle valves are engineered to provide a reliable method for isolating instrumentation from the process and for throttling or shut-off requirements. AE eries 5000 Valves are bubble tight in both the seated and back seated positions. Both hard and soft seated models are available. These needle valves will accept a variety of pipe sizes from 1/4" to 1" and are rated for either 6,000 psi (414 bar) or 10,000 psi (690 bar). Gauge Valves Gauge valves are primarily used to isolate the process from instrumentation such as gauges or transducers. These valves are typically used in conjunction with block and bleed valves. AE eries 5000 gauge valves are available with an extended length between the inlet and the bonnet centerline to ensure the valve extends far enough from the process connection to clear the pipeline insulation or to distance a socket weld end from the bonnet. Autoclave gauge valves accept a variety of bonnet styles, threaded pipe sizes and socket welds and are rated for service to 6,000 psi (414 bar). Pressure vs. Temperature Ratings for body, seat and packing materials Instrument Manifold Valves Autoclave instrument manifold valves provide a safe, economical and convenient method of isolating, blocking, bleeding and calibrating instruments, meters and pressure transmitters. These valves are available in numerous body, bonnet and seal configurations with FNPT, tube fittings and/or instrument flange connections. AE eries 5000 instrument manifold valves operate to pressures of 6,000 psi (414 bar) and offer excellent flexibility with different body patterns and hard seat models utilizing either a vee, ball or non-rotating stem. Valve models include 2, 3 and 5 bonnet remote line mounting; 2, 3 and 5 bonnet direct mounting single flange; and 2 and 3 bonnet direct mounting, dual flange. Vee, ball and non-rotating tips are available in hard seat models; soft seats use only vee tip stems. ustomer upport Autoclave Engineers is prepared to assist you in every phase of the design/application cycle. Our technical sales specialists will work with your design team to ensure the correct valve configuration is selected, and/or to custom engineer a special valve for your individual requirements. Our worldwide sales and service organization is available to conduct any on-site review/analysis of your application requirements or to provide timely installation and repair services. Whatever your need, Autoclave's engineering experience and customer oriented focus will help you find a solution. 6,000 (414) 316 Pressure PI (bar) 5,000 (345) 4,000 (276) 3,000 (207) 2,000 (138) 1,000 (69) Viton "O" Ring Grafoil Packing A105 Arlon 1000 eat Teflon Packing 100 (37.8) 200 (93) 300 (149) 400 (204) 500 (260) 600 (316) Temperature ϒF (ϒ) 700 (371) 800 (427) 900 (482) 1000 (538) Note: oft seats are bubble-tight at pressure vs. temperature ratings shown above. Metal seat meets ANI B6.04 lass V. All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

3 Two Valve alibration Manifold - 6M2R 6M2R two valve calibration manifold provides an econoical and convenient method of blocking, bleeding and calibrating pressure transmitters. This valve may be mounted rigidly to a mounting bracket, providing a safe isolation valve, while reducing the number of fittings and space required for installation..75" 0.25" Available with needle or self aligning ball stem (19.1) (6.4) 2.50" 3/16" bore 3.81" Typical ordering number: 6M2RF44TD-2 alibration & Bleed Port Instrument Port Process Port 2.50" (63.5) (63.5) (2) 9/32" dia. mounting holes alibration valve (96.8) max. open 2.50" (63.5) 5.06" (128.5) max. open 6M2R F44T D 2 6M2R F44T - 1/2" FNPT x 1/2" FNPT F44P - 1/2" integral tube fitting process connection x 1/2" FNPT D - Ball stem/ L - Locking device Three Valve Manifold - 6M3R 6M3R three valve manifold features over-sized Type bonnets to provide maximum durability. Two block valves and one equalizing valve are designed in a single body, making the manifold ideal for on-line instrument calibration. Integral valve construction eliminates the use of numerous valves, nipples and fittings. Large 3/16" diameter equalizing ports for viscous fluid service applications 3/16" bore Equalizer valve 4.38" (111.3) max. open 9/32" dia. mounting holes 2.88" (73.2).75" (19.1) 3.63" (92.2) 9.75" (247.7) max. open Typical ordering number: 6M3RF44T-G 6M3R F44T G 6M3R F44T - 1/2" FNPT x 1/2" FNPT A - Needle stem/ Viton O-ring - Ball stem/ All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 3

4 Five Valve Metering Manifold - 6M5R 6M5R five valve metering manifold consists of two shut off valves, two equalizing valves and a single vent valve. This single unit takes the place of the conventional piped up 5-valve manifold generally found on field meters or gas service differential transmitters. Replaceable soft seats of Arlon with rodding out capability on block valves with & D bonnets Arlon soft seat inserts available for equalizers and bleed valve with N bonnets 3/16" bore Bleed Valve Equalizer Valve Equalizer Valve 3.81" (96.8) max. open optional 1/4" static connections on bottom vent Equalizer Valve Line Valve 3.63" (92.2) Line Valve Line Valve Line Valve 3.00" (76.2) (2) 9/32" dia. mounting holes 1.00" Bleed Valve (25.4) Max. open 10.00" (254.0) Typical ordering number: 6M5RF44PND-L 6M5R F44P ND L 6M5R F44T - 1/2" FNPT x 1/2" FNPT F44P - 1/2" integral tube fitting process connection x 1/2" FNPT - Ball stem/ N - Needle stem/ L - Locking plate 2 - Arlon soft seat material ("ND" bonnet/ line valves only 4 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

5 Two Valve Manifold ingle Flanged - 6M2D 6M2D two valve, single-flanged manifold is designed for direct mounting to static pressure instruments where calibration capability is required. Rugged one piece construction is ideal for applications where remote mounting from the process is desired without compromising instrument stability. This calibration manifold features compact design and secure installation by eliminating unnecessary piping, valves and fittings. A rigid mounting kit is provided for convenient pipe stand unit assembly. Teflon gasket 6.75" (171.5) max. open 3.63" (92.2) Bleed valve 1/4"-20N mounting holes 1/4" FNPT vent Type "" & "F" valve bonnets feature self centering ball stem, providing positive shut-off capability 3/6" bore vent 2.38" (60.5) 3.75" (95.3) max. open Typical ordering number: 6M2DF49TF-G 3.81" (96.8) 6M2D F49T F G 6M2D F49T - 1/2" FNPT x Flanged Block Valve: - Ball stem/ Bleed Valve: F - Ball stem/ Three Valve Manifold ingle Flanged - 6M3D 6M3D three valve, single flanged manifold bolts directly to the pressure differential transmitter. This unit is used in applications where close coupling to orifice flanges is not desired. These manifold valves provide safe operation and eliminate the need for unnecessary piping, valves and fittings. The manifold comes complete with mounting kit for quick and easy installation. tandard (54.1mm) center-to-center inlets and outlets pecial 2.19" (55.6mm) center-to-center instrument flange outlets available 3/16" bore Equalizer valve (2) 9/32" dia. mounting holes 3.63" (92.2) 1.00" (25.4) 0.88" (22.4) Max. open 10.00" (254.0) 4.38" (111.3) max.oper Typical ordering number: 6M3DF49T-L 6M3D F49T L 6M3D F49T - 1/2" FNPT x Flanged - Ball stem/ N - Needle stem/ L - Locking plate A - Arlon soft seat material ("N" bonnet only) All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 5

6 Five Valve Manifold ingle Flanged - 6M5D 6M5D five valve manifold mounts directly to the differential pressure transmitter. The two horizontal block valves allow easy removal of the instrument for servicing and the three valves on top of the manifold provide an easy method for accurate field calibration using the manifold vent connection rather than the instrument drain connections. Manifolds are shipped complete with mounting kit for quick and easy installation. elf-centering ball seats provide positive shut-off tandard center-to-center inlets and outlets pecial 3.11" (79.0) center-to-center instrument flange outlet available 3/16" bore 4.38" (111.3) 2.38" (60.5) Bleed Valve Equalizer Valve optional 1/4" static connections on bottom 1/4" FNPT vent 4 mounting holes Teflon gasket 31/64" dia. on 1.63" (41.4) center 1/4" 20 N mounting holes vent ("" bonnet assembly) 9.75" (247.7) max. open 3.63" (92.2) ( bonnet assembly) Typical ordering number: 6M5DF49TD-L 6M5D F49T D L 6M5D F49T - 1/2" FNPT x Flanged F49P - 1/2" integral tube, single ferrule process connection x Flanged - Ball stem/ N - Needle stem/ L - Locking plate A - Arlon soft seat material ("DN" bonnet only) 6 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

7 Three Valve Manifold Dual Flanged - 6M3F 6M3F three valve, dual flanged manifolds is designed for close mounting differential pressure instruments to orifice flanges or orifice changer fittings. The flanged valve outlet is bolted directly to the pressure transmitter body. By bolting standard football flanges to the manifold inlet, the complete assembly can be close coupled to orifice flange taps using eccentric solid bar stock nipples. These manifold valves provide a simple, rugged and dependable installation. Available with needle or self-aligning ball stems tandard center-to-center inlets and outlets 3/16" bore 3.69" (93.7) 4 holes 31/64" dia. 1.63" (41.4) 3.81" (96.8) 4 holes 7/16" x " (12.7) deep 2.38" (60.5) 2 holes 1/4" 20 at 1.00" (25.4) centers 0.38" deep at rear 1.38" (35.1) Typical ordering number: 6M3FF99T-G 3.63" (92.2) 10.00" (254.0) max. open 6M3F F99T G 6M3F F99T - Flanged x Flanged - Ball stem/ N - Needle stem/ L - Locking plate A - Arlon soft seat material ("N" bonnet only) All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 7

8 3/8" Bore Roddable Manifold Valve - 6M3 6M3 three valve single or double flanged manifold bolts directly to the pressure differential transmitter. This unit is used in applications where close coupling to orifice flanges is desired. These manifold valves provide safe operation and eliminate the need for unnecessary piping valves and fittings. The manifold comes complete with mounting kit for quick and easy installation. The bonnet assembly is suitable for severe service applications. 4.00" (101.6) 5.13" (130.3) closed 5.38" (136.7) open 4 holes 31/64" dia. 1.50" (38.1) 5.66" (143.8) tandard center-to-center inlets and outlets pecial 3.11" (79.0) center-to-center instrument flange outlet available 1.63" (41.4) 1.88" (47.8) 1.12" (28.4) Two 9/32" holes at 1.00" center 11.50" (292.1) closed 12.50" (317.5) open 3.88" (98.6) Typical ordering number: 6M3F49TH-A 6M3 F49T H A 6M3 F44T - 1/2" FNPT x 1/2" FNPT F49T - 1/2" FNPT x Flanged F49P - 1/2" integral tube fitting process connection x Flanged F99T - Flanged x Flanged H - Threaded bonnet, tapered, self-aligning, nonrotating plug/ K - Threaded bonnet, tapered, selfaligning, non-rotating plug and non-rotating stem (for high temperature, with Grafoil packing) A - Arlon soft seat material ("H" bonnet only) 8 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

9 3/16" Orifice Liquid Level Manifold - 6M2L 6M2L manifold uses the hydrostatic head technique to efficiently utilize a differential pressure transmitter for level measurement. The 6M2L reduces the number of vessel entry points which eliminates the need for instrument piping supports. This reduces the installation cost on pressurized or atmospheric vessels requiring a "wet log" or "diptube" utilizing the 6M2L's unique mounting system. 4 holes 31/64" dia. 3.81" (96.8) Optional Arlon soft seats Available with needle or self-aligning ball stems tandard center-to-center inlets and outlets 4 holes 7/16" x 20.50" (12.7) deep 1.63" (41.4) 2.38" (60.5) 3.63" (92.2) 10.00" (254.0) max. open Typical ordering number: 6M2LF99TN-A 6M2L F99T N G 6M2L F49T - 1/2" NPT x Flanged F49P - 1/2" integral tube fitting process connection x Flanged F99T - Flanged x Flanged - Ball stem/ N - Needle stem/ A - Arlon soft seat material ("N" bonnet only) All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 9

10 Three Valve Meter Manifold - 6M3M 6M3M three valve meter manifold is designed for convenient isolation, venting and on-line calibration of local chart recording meters. Durable bar stock body construction with integral equalizing and vent valves is ideally suited for mounting beneath field meter cases. Replaceable Arlon soft seats are field serviceable and feature positive shut-off capability Multi-ported pressure taps allow static pressure measurement to be taken upstream or downstream 4.31" (109.5) max. open Vent port sq. 3.75" max. open (95.3) 10.00" (254.0) Two Valve alibration Manifold 3/8" Bore, Roddable - 6M2 6M2 two valve pressure manifold is designed for remote mounting, single-instrument applications. Both line and vent valves are integral with the single piece body making this manifold ideal for on-line calibrations and testing. It is also available with process tube connections. One-piece solid barstock construction High temperature model available Optional, replaceable, roddable Arlon soft seats Vent Inst. 0.88" (22.4) 3.75" (95.3) 1.75" (44.5) 0.75" (19.1) 2 holes 9/32"dia. 7.50" (190.5) closed 8.00" (203.2) open Proc. 1.13" (28.7) 0.75" (19.1) 3.75" (95.3) 0.25" (6.35) 1.75" (44.5) 5.63" closed 6.13" open (143.0) (155.7) Typical ordering number: 6M3MF22TN-2 6M3M F22T N 6M3M 6M2 F22T - 1/4" FNPT x 1/4" FNPT F44T - 1/2" FNPT x 1/2" FNPT F44P - 1/2" integral tube fitting process connecton x 1/2" FNPT Equalizing valves: N - Needle stem/ Vent Valves D - Ball stem/ H - Threaded bonnet, tapered, self-aligning non-rotating plug/ K - Threaded bonnet, tapered, self-aligning, non-rotating plug and non-rotating stem (with Grafoil packing) (For both 6M3M and 6M2) (except "H" bonnet) A - Arlon soft seat material ("H" bonnet only) 10 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

11 Two Valve ingle Mount alibration Manifold - 6M2M 6M2M two valve pressure manifold is designed for direct mounting, single instrument applications. ecure installation is ensured by a rigid mounting block manifold. Both line and vent valves are integral with the single piece body making this manifold ideal for on-line calibration and testing. Type "" and "F" bonnets feature self centering ball stem, providing positive shut-off capability 3/16" bore 4.38" (111.3) max open Adapter Teflon gasket Dia. 11/32" 2.88" (73.2) Bleed valve 3.50" (88.9) 6.13" (155.7) max. open 0.75" (19.1) 4.56" (115.8) Inst. Vent Proc. Two Valve Dual Mount Manifold - 6M4M 6M4M two valve dual mount manifold connects two separate pressure instruments to a single process connection and assures secure installation. Twin sets of integral block and bleed valves are provided in a single piece body allowing independent instrument operation and servicing. Vent Inst. Inst. Vent eparate integral bleed valves with 1/4" lower side vent connections Type "" and "F" valve bonnets feature self-centering ball stem, providing positive shut-off capability Proc. 11/32" dia. 1.00" (25.4) 6.50" (165.1) 2.88" (73.2) 4.56" (115.8) 4.38" (111.3) max. open Adapter 6.88" (174.8) max. open Typical ordering number: 6M4MF44TN-2 Teflon gasket Bleed valve 6M4M F44T N G 6M2M F44T - 1/2" FNPT x 1/2" FNPT - Ball stem/ N - Needle stem/ (For both 6M2M and 6M4M) 6M4M F44T - 1/2" FNPT x 1/2" FNPT Block valves: - Ball stem/ packing Bleed valves: N - Needle stem/ packing All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 11

12 Equalizing Valve - 6M1D The 6M1D equalizing valve is an economical valve with compact body, designed to mount between the differential pressure transmitter and the flanges which are generally supplied with the transmitter. A mounting kit is provided for quick and easy installation. Replaceable Arlon soft seats are field serviceable and feature positive shut-off capability Multi-ported pressure taps allow static pressure measurement to be taken upstream or downstream 1.625" (41.3).95" (24.1).68" (17.3) (54.0) 6.13"(155.6) max. open Equalizer Valve Typical ordering number: 6M1DD- 6M1D G 6M1D D - Ball stem/ Two Valve Direct Mounting Miniature Manifold - *6,000 psig (414 bar) - 6M2P Rated to 10,000 psi (690 bar) Direct mounting to miniature transmitters without utilizing mating flange Integral vent for process isolation & removal Inst. Proc. Vent 4.87"(123.7) open 1.63" (41.4) 2.38" (60.5) Partial section illustrating connection for Rosemount transmitter #3051 F2A (33.0) 2.63" (92.2) F2B Typical ordering number: 6M2PF2ADN " (27.0) 5.0" (127.0) 6M2P 6M2P *For Rosemount 3051 transmitters **F & **FN bonnets are utilized to obtain 10,000 psi (690 bar) rating F2A *F2A - Flange x flange with.30" (33.0) centers F2B - Flange x flange with.14" (54.4) centers DN B - Needle stem/ viton o-ring D - Ball stem/ DN - Needle stem/ **F - Ball stem/ **FN - Needle stem/ A - Arlon soft seat material ("DN" & "BN" bonnets only) 12 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

13 Five Valve Direct Mounting Miniature Manifold - 6,000 psig (414 bar) - 6M5P Direct mounting to miniature transmitters without utilizing mating flange Integral vent for process isolation & removal Inst. Inst. 9.75" (247.7) open 2.38" (60.5) Proc. Vent Proc. Partial section illustrating connection for F2B 2-1/8" center transmitter 1.63" (41.4) 2.63" (66.8) 1.3" (33.0) Typical ordering number: 6M5PF2ADN- flow 5.00" (127.0) flow 6M5P 6M5P **F & **FN bonnets are utilized to obtain 10,000 psi (690 bar) rating F2A *F2A - Flange x flange with.30" (33.0) centers F2B - Flange x flange with.14" (54.4) centers DN B - Needle stem/ viton o-ring D - Ball stem/ DN - Needle stem/ **F - Ball stem/ **FN - Needle stem/ A - Arlon soft seat material ("DN" & "BN" bonnets only) All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 13

14 Instrument Manifold Valves - s Assemblies Autoclave Engineers needle, gauge and instrument manifold valves utilize several different bonnet styles to increase operational flexibility and process compatibility. These bonnets offer both adjustable and non-adjustable packing as well as designs incorporating ball or needle stems, non-rotating stems and a non-rotating plug. tandard materials for bonnet, stem and handle construction are offered in either carbon or stainless with monel available as an option. Handles are pinned to the stem and are designed to sheer the pin to prevent over torquing. tandard seal materials are Viton O-rings or with Grafoil packing available as an option. tem back seat the bonnet for a metal-to-metal seal isolating the packing from the process. All stem packing is located below the stem threads thereby isolating stem threads from process fluids. All bonnets include color-coded dust covers to prevent. abrasive materials from entering the stem threads. The color coding identifies the packing materials. All threaded bonnets include a lock pin to prevent accidental removal of the bonnet. Lockplates also available as an option and are standard on the H and K bonnets. eal Temperature Limits Type Minimum Maximum over Temperature Temperature olor Viton O-ring -20 F (-29 ) 400 F (204 ) orange Teflon Packing -100 F (-73 ) 500 F (260 ) red Grafoil Packing -40 F (-40 ) 1000 F (538 ) silver For NAE requirements-needle stem required Type A (Interchangeable with "" bonnet) Type B (Interchangeable with "D" bonnet) oft eat Hard eat Handle (12L14 or 303 ) Handle (12L14 or 303 ) Dust cover (plastic) Dust cover (plastic) crewed bonnet (carbon or 316 ) Back-up ring (Teflon) O ring (Viton) tem (303 or 316 ) eat (Arlon) Lock Pin crewed bonnet (carbon or 316 ) Back-up ring (Teflon) O ring (Viton) tem (303 or 316 ) 14 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

15 Instrument Manifold Valves - s Type Optional needle stem available ( N ) (Interchangeable with A bonnet) Hard eat Type D Optional needle stem available ( DN ) (Interchangeable with B bonnet) Hard eat Handle (12L14 or 303 ) Handle (12L14 or 303 ) Dust cover (aluminum) Dust cover (aluminum) Packing adjuster (carbon or ) Packing adjuster (carbon or ) Lock nut (carbon or ) Lock-nut (carbon or ) crewed bonnet (carbon or 316 ) crewed bonnet (carbon or 316 ) Packing (Teflon or Grafoil) Lock Pin Packing (Teflon or Grafoil) Lock Pin tem (303 or 316 ) 316 ball tem (303 or 316 ) 316 ball Type E Type G Handle (12L14 or 303 ) Hard eat Handle (12L14 or 303 ) Hard eat Dust cover (plastic) Yoke head (12L14 or 303 ) Dust cover (aluminum) Yoke stud (stress proof or 316 ) Packing washer (12L14 or 303 ) Packing follower (316 ) Packing (Teflon) Packing guide (316 ) Bolted bonnet (1018 or 316 ) Gasket (Flexitalic) tem (303 or 316 ) Packing tud (stress proof or 316 ) Packing adjuster (carbon or ) Lock-nut (carbon or ) crewed bonnet (carbon or 316 ) Packing (Teflon or Grafoil) tem (303 or 316 ) 316 ball Lock Pin Type H Hard and oft eat Type K (For high temperature and severe service applications) Handle (303 ) Handle (4140) Dust cover (aluminum) Packing adjuster (416 ) Lock-nut (303 ) crewed bonnet (316 ) Injection Nipple Packing adjuster (416 ) crewed bonnet (316 ) Injection nipple Packing (Teflon) tem (316 ) Plug (416 ) eat (316 or Arlon) Packing (Grafoil) Lock nut () tem (316 ) Plug (416 ) eat (316 ) All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 15

16 Instrument Manifold Valves - Accessories Gauge iphon- 6G 5.75" (146.1) (Approximate) 1/2"-FNPT Gauge onnection 2.28" (57.9) Typical ordering number: 6GM44T 1/4" Inner Tube Outer Tube RETRITED FLOW FEATURE 1 In case of gauge process flow would be restricted to approximately 10% if volume. 1 Patent Pending Hexagon 1/2"-14 MNPT 6G 6G M44T M44T - 1/2" MNPT x 1/2" FNPT Bleed Valve with Integral Vent- 6BV Typical ordering number: 6BVM4T 1/2" MNPT tandard Bleed Valve 1/2" MNPT Optional Bleed Valve with Tee Handle 6BV M4 T 6BV M4-1/2" MNPT T - Tee handle bleed All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.! WARNING! FAILURE OR IMPROPER ELETION OR IMPROPER UE OF THE PRODUT AND/OR YTEM DERIBED HEREIN OR RELATED ITEM AN AUE DEATH, PERONAL INJURY AND/OR PROPERTY DAMAGE. This document and other information from nap-tite, Inc., its subsidiaries and authorized distributors, provides product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operation conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by nap-tite, Inc. and its subsidiaries at any time without notice. IO-9001:2000 ertified BE-0107 Industrial Estate Whitemill-Wexford 8325 Hessinger Drive Republic of Ireland Erie, Pennsylvania UA PH: FAX: PH: FAX: ste_sales@snap-tite.com ae_sales@snap-tite.com All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.