TCD (H2) EFC INSTALLATION

Transcription

1 DOC: PAGE: of TCD (H2) EFC INSTALLATION CONTROL: INDUSTRIAL ENGINEERING. DATE:

2 DOC: PAGE: 2 of INJ FRONT DET. FRONT INJ MIDDLE DET. MIDDLE INJ REAR DET. REAR MANIFOLD PLUMBING SCREW, 4EA ASSY., TCD AND OVEN, 20V NOTE: SEE PAGE 0 FOR PWA CONNECTION ASSY., TCD AND OVEN, 230V ASSY., TCD AND OVEN, 0V ASSY., TCD AND OVEN, W/ TRANSFER LINE 20V NOTE: TOP OF THE COLUMN OVEN, CUT AWAY FOR CLARITY REFERENCE MAKE UP ASSY., TCD AND OVEN, W/ TRANSFER LINE 220V ASSY., TCD AND OVEN, W/ TRANSFER LINE 0V NOTE: SEE MOTHER BD. FOR HTR. PROBE CONN SCREW, 4EA TRANSFER LINE CONTROL: INDUSTRIAL ENGINEERING. DATE:

3 DOC: PAGE: 3 of CABLE INSTALLATION CABLE PLUG-IN TO MAIN BOARD CABLE, FLAT FOR DETECTOR EFC CONTROL: INDUSTRIAL ENGINEERING. DATE:

4 DOC: PAGE: 4 of INLET MANIFOLD SUBASSEMBLY TUBING, PEEK /8 26 (NATURAL) TUBING, PEEK 22 (RED) , 3 PLCS NUT, VITON FERRULE , 3 PLCS WASHER, FERRULE , 3 PLCS VITON, FERRULE INLET MANIFOLD CONTROL: INDUSTRIAL ENGINEERING. DATE:

5 DOC: PAGE: 5 of MODULE INSTALLATION , 2 PLCS SCREW, GROMMET, FLEXIBLE 7 CONTROL: INDUSTRIAL ENGINEERING. DATE:

6 DOC: PAGE: 6 of INLET MANIFOLD INSTALLATION NOT USE (REF.) ( , /8 NATURAL) CARRIER INLET ( , RED) H2 INLET NOT USE (REF.) CONTROL: INDUSTRIAL ENGINEERING. DATE:

7 DOC: PAGE: 7 of MODULE INSTALLATION NOTES:. CONNECT CABLE TO MODULE, THEN MOUNT MODULE TO FRONT PANEL. 2 MOVE MODULE LOCATION JUMPER TO SPECIFY FRONT, MIDDLE, OR REAR. 3. ADD CABLE HOLDER WHEN NO REAR MODULE PRESENT. NOTE MOUNTING LOCATION , 4 PLCS SCREW, 6-32 DET. FRONT DET. MIDDLE DET. BACK 2 JUMPER LOCATION (REF.) EFC MODULE, TCD (H2) CABLE HOLDER 3 CONTROL: INDUSTRIAL ENGINEERING. DATE:

8 DOC: PAGE: 8 of ADDITIONAL MODULE CABLEING (IF REQ D) NOTE CABLE SERVICE LOOP FOR ADDITIONAL DETECTOR EFC MODULE CONTROL: INDUSTRIAL ENGINEERING. DATE:

9 DOC: PAGE: 9 of PNEUMATICS SIDE MANIFOLD REFERENCE ONLY PNEU. MANIFOLD MODULE PNEUMATICS CONNECTIONS REFERENCE LINE FROM MODULE TO DETECTOR RED (26 ) MAKE UP LINE FROM MODULE TO DETECTOR RED (26 ) MAKEUP LINE TO MODULE, RED (6 ) CHANNEL REFERENCE MODULE, RED (6 ) CHANNEL 2 REF. ONLY VITON FERRULE SCREW CONDYNE PLATE NOTES:. DRESS PLUMBING IN PNEUMATICS COMPARTMENT USING CABLE TIE. INSPECT TO ENSURE PNEUMATICS PANEL SWINGS FREELY. CONTROL: INDUSTRIAL ENGINEERING. DATE:

10 DOC: PAGE: 0 of NOTE: POSITION & ROUTING OF CABLE AND TIES NOT NESS. AS SHOWN. DRESS CABLE W/ QTY. NEEDED USING AVAILABLE SPACE ASSY., TCD, PCB CONNECTION TO TCD PWA CLICK HERE FOR PROBE CONNECTION TO J7 ON MAIN BD. CLICK HERE FOR HEATER CONNECTION J4 ON POWER BOARD TCD PWA INSTALLATION FLAT, WASHER SCREW, 6-32 X / , 2 PLCS SET SPRING WASHER MOUNTING SCREWS DETAIL CLAMP, CABLE, STANDOFF CONTROL: INDUSTRIAL ENGINEERING. DATE:

11 DOC: PAGE: of TCD DETECTOR LOCATION 6 5. TCD (4) IS FRONT (5) IS MIDDLE (6) IS REAR TCD WITH ONE OTHER DETECTOR USE (4) AND (5) TCD 4 CONTROL: INDUSTRIAL ENGINEERING. DATE: