INTELLIQUILTER INSTALLATION ON INNOVA VERSION

Size: px
Start display at page:

Download "INTELLIQUILTER INSTALLATION ON INNOVA VERSION"

Transcription

1 INTELLIQUILTER INSTALLATION ON INNOVA VERSION EDGERIDER WHEELS ON THE CARRIAGE Slightly loosen the bolts ( A ) on the bracket that holds the front wheels, so it can allow for changes in the alignment of the rear wheels. Fig. 1 Prop up the middle of the rear wheel bracket and replace one of the outer wheels with a fixed-hub E/R wheel. Use the existing washer ( A ) and locknut ( B ). Move the bolt in the middle of the slot and tighten the nut. 1

2 Fig. 2 Replace the other outer wheel. Use the enclosed height leveler block ( A on Fig. 3) instead of the original nut. Set the adjusting screw ( B on Fig. 3) to its outermost position and push the wheel mounting screw to the top of the slot. Tighten the bolt enough to hold the wheel, but allow adjustments. Drive in the adjusting screw to pull the wheel down, until all four wheels have traction. 2

3 Fig.3 Remove both inner wheels and position the E/R wheels on the top of the track. You may need to slide the front wheel bracket in/out to allow this. Prop up the front of the carriage and replace both front wheels with sliding-hub E/R wheels using the existing washers and locknuts. Move the front bracket in/out until the middle of the groove of the wheels is aligned with the top of the rails and there is equal clearance on the sliding hub on both sides of the wheel. Roll the carriage all the way along the table and check the alignment of the wheels. If you find bent spots on the rails, or misaligned rails, correct them. The carriage should roll freely, with no noticeable drag. 3

4 2. COMPUTER BRACKET Remove one of the bolts that hold the front handles. Place the computer bracket on the top as Fig. 4 shows and mount it over the handle using the included bolt and the serrated washer above, the spacer below the computer bracket. Keep the bolt loose. Repeat the above on the other side. Push the mounting block of the handles against the black block on the head and tighten the bolts firmly to avoid any movement of the handles. Fig. 4 4

5 Remove the yellow thumbscrews and the other two screws on the docking station. Mount the docking station on the bracket. 3. THREAD BREAK DETECTOR Position the thread break detector on the top of the arm, so the hole in the bracket is about 2" (50mm) from the rear edge of the head and 1-1/4" (32mm) from the edge of the arm, as Fig. 5 shows. Clean the surface where the bracket will be placed with alcohol. Remove the clear protective foil from the double-sided tape on the bracket and push it firmly to the surface. Set the wheel position so it is aligned with the thread path as Fig. 5 shows. NOTE the proper threading: the thread goes up/down/up in the three-hole guide, then wrapped around the wheel once clockwise. Fig. 5 5

6 4. Y-MOTOR The EdgeRider wheels come with proper spacing, you don t need to use any of the original washers. Remove the rear left wheel (viewed from the font). Loosen the hex bolt that holds the sensor bracket to the rear axle and slide off the sensor from the axle. Mount a fixed EdgeRider wheel on the axle; don t use any of the original washers. Don t tighten the bolt, for it will be removed when you install the Y-motor. Fig. 6 Remove the wheel from the front left axle (viewed from the front). Remove the screws ( A and B on Fig. 7) holding the sensor and turn the sensor 180 degrees. 6

7 Slide in the sensor bracket, so the sensor is facing the back as Fig. 7 shows. NOTE that you may need to pull the sensor wire from the back to provide enough slack. Mount a fixed-hub E/R wheel on the front axle Fig. 7 Remove the rear right wheel (viewed from the front) and mount a sliding EdgeRider wheel on the axle. Install a sliding EdgeRider wheel on the front right axle. 7

8 Fig. 8 Push up the sensor wheel of the Y-motor and hold it at its highest position with the included spacer tool as shown on Fig. 8. Loosen the T-nuts (1 and 2) on the bracket. Remove the EdgeRider wheel from the rear left axle and slide the T-nuts in the top groove. Replace the wheel and tighten its bolt. Hand-tighten the screws and align the motor so the bracket is parallel with the carriage track and the gap between the drive roller and the side of the track is about 3/32 (2 mm), as shown on Fig. 9. Tighten the 1 and 2 screws firmly. Remove the spacer tool from the sensor limiting screw. 8

9 Fig. 9 Set the drive wheel parallel with the side of the track as Fig. 10 shows, using screws C and D on Fig. 9. 9

10 Fig 10 10

11 Hold a long ruler at the sensor wheel s side and adjust the bracket with screws A and B until the ruler is parallel with the top of the track. Tighten all four screws at this position. Fig

12 5. X-MOTOR Remove the nut and washers from the ¼ -20 bolt ( A ). Loosen the B screw until its end is flush with the tab on the bracket adjuster. Push the motor bracket to the tab. Fig. 12 Hold the bracket aligned with the second hole from the bolt that holds the front wheel bracket on the right-hand rail (viewed from the front). Drive in and tighten the ¼ -20 bolt. It is recommended to use a C-clamp or vise-grip to hold the bracket to the bottom of the carriage rail, as shown on Fig. 13. Put back the flat washer, the lock washer and the nut on the bolt and tighten the nut just enough so you can use the B adjustment screw. Push up the sensor wheel of the X-motor and hold it with the spacer tool. Mount the motor on the bracket. 12

13 Fig. 13 Turn the B adjustment screw to move the bracket closer to the track. The gap between the drive roller and the side of the track should be about 3/32 (2 mm), as shown on Fig. 10. Tighten the 1/4-20 bolt firmly. Remove the spacer tool from the sensor limiting screw. 13

14 Fig. 14 Fig

15 Set the drive wheel parallel with the side of the track using screws A and B. on Fig. 15. Hold the ruler at the sensor wheel s side and adjust the bracket with screws C and D until the ruler is parallel with the top of the track. Tighten all four screws at this position. Fig. 16 Install the two rubber stoppers on the top of the rear table rail, at positions that prevent the motors from bumping into the frame. 15

16 6. JUNCTION BOX Remove the drop-in nut from the junction box bracket and insert it in the top channel of the rear cross-bracket of the carriage. Mount the junction box horizontally, with the cables facing the back, using one ¼ - 20 x 1/2 screw. Fig

17 7. INSTALLATION OF CABLES Remove the cover from the back of the arm. Push the switch cable through the hole of the rear plate ( A ) and run it to the front in the lower channel on the left side of the upper arm (viewed from the front). Tie the cable to the cable harness ( B ) as Fig. 18 shows. Fig. 18 Unplug the R1 and L1 connectors from the main board. Plug in the connectors to the switch cable adapters as Fig. 19a shows: - R1 to the socket with R1 marker (BLACK and RED wires). - L1 to the socket with L1 marker (GREEN and WHITE wires). Plug in the adapters to the corresponding R1, L1 connectors as Fig 19b shows. 17

18 Fig. 19a Fig. 19b Insert the switch cable to the 6-position screw terminal as Fig. 20 shows. (1-GREEN, 2-WHITE, 4-RED, 5-BLACK) Fig

19 Bring forward the computer and Y-motor cables on the bottom of the rear compartment and push them through the opening on the front. Fig. 21 Run the computer cable up in the outer channel of the rear column and in the lower channel of the upper arm, where the switch cable is inserted, as Fig. 22 shows. Plug in the 2-position green communication connector and the power jack on the docking station. Pull back the cable, leaving some slack at the docking station, as Fig. 24 shows. Run the Y-motor cable directly to the motor. Plug in the cable and pull it back, leaving some slack at the motor. 19

20 Fig. 22 Hold together the Y-motor and computer cables at the back with wire ties and form a loop that allows both extreme arm positions without pulling the cables, as Fig. 17 shows. Tie the cables to the machine s power cord and replace the rear cover. Run the X-motor cable on the inside of the left carriage rail (viewed from the back) toward the front, as Fig. 23 shows. Clean their locations with alcohol and place sufficient number of cable clips along the rail. Plug in the cable on the X-motor, leaving some slack. 20

21 Fig

22 Fig. 24a Fig. 24b Plug in the thread break detector cable, arrange the cables and tie them with wire ties, as Fig. 24b shows. Secure the cables in the channels by replacing the channel covers. 22

23 Tie the cables on both motors with a wire tie as Fig. 25 shows. Fig

24 Put the plastic covers on the motors. Pull up the cable in the slot at the side of the cover as Fig. 26 shows. Fig

25 Remove the protective cover from the terminal of the motor power supply. Push the power cable through the wire-tie loop and connect the wires to the power supply: BLACK wire to the negative terminal, the wire with the in-line diode to the positive terminal. Tighten the wire tie. Replace the protective cover. Fig

26 Mount the power supply on the rear middle table leg using two 14" cable ties as Fig. 28 shows. Fig

27 8. COMPUTER SETUP Turn on the computer. When the booting completes, the motors will be engaged with the tracks. Select Manual Mode and move the motors all the way on the tracks. Check the gap between the drive wheel and the track. If the gap changes over the range, set the gap to 3/32 (about 2 mm) at the closest location. Go to Utilities->Preferences. Set the motor engagement strength for each motor separately. Start with a lower number, then increase the number and test the resistance of the motor in each direction, until there is definite resistance everywhere. The optimal settings range is on the standard motors, on the SuperMotors. You need to raise the motor if the final setting is below the lower limit, lower it if the setting is above the upper limit. Set the X-motor engagement strength when the arm is pushed all the way back. Go to Utilities->Measure/Calibrate and calibrate the sensor wheels following the onscreen instructions. Go to System->Interface Setup/Test. Ask the customer to set her/his preference for half or full cycle when the single stitch switch is pushed. Set the Single Stitch Phase accordingly. If the half stitch option is selected, warn the customer that the needle should be set at the top position before entering the Sew Quilt or Preview mode. Set the delays and pulse durations to match the electronic control of the quilting machine. Test the single stitch and start switches, and the thread break detector. Note that the detector works only when the machine is stitching (the Start Switch label is red). If the needle positioner is slow on the machine, increase the delays before and after the single stitch. Set the local date and time. Enter at least eight digits: two digits for the month, two digits for the day, two digits for hours (in 24-hour format) and two digits for minutes. Continue with another four digits for the year only if the display does not show the proper year. Show the brightness control to the customer and set the desired level. COPY THE LOGS AND THE logs.tar.gz FILE TO support@intelliquilter.com. 27

INTELLIQUILTER INSTALLATION ON A-1 MACHINES VERSION

INTELLIQUILTER INSTALLATION ON A-1 MACHINES VERSION INTELLIQUILTER INSTALLATION ON A-1 MACHINES VERSION 06.13.13 Before the IQ installation swap the wheels on the carriage, so the grooved, dual ball-bearing wheels are on the front. 1. DOCKING STATION Remove

More information

INTELLIQUILTER INSTALLATION ON PRODIGY VERSION

INTELLIQUILTER INSTALLATION ON PRODIGY VERSION INTELLIQUILTER INSTALLATION ON PRODIGY VERSION 05.09.16 1. COMPUTER BRACKET Remove the drop-in nuts from the tablet mounting bracket and insert them in the slots at the top of the upper arm, just behind

More information

INTELLIQUILTER INSTALLATION ON GAMMILL MACHINES VERSION

INTELLIQUILTER INSTALLATION ON GAMMILL MACHINES VERSION INTELLIQUILTER INSTALLATION ON GAMMILL MACHINES VERSION 11.10.13 1. COMPUTER BRACKET From the left side of the head (viewed from the front) remove the three screws circled on Fig 1. Fig. 1 Remove the tablet

More information

INTELLIQUILTER INSTALLATION ON APQS MILLENNIUM/FREEDOM SR ON BLISS-READY TABLE VERSION

INTELLIQUILTER INSTALLATION ON APQS MILLENNIUM/FREEDOM SR ON BLISS-READY TABLE VERSION INTELLIQUILTER INSTALLATION ON APQS MILLENNIUM/FREEDOM SR ON BLISS-READY TABLE VERSION 02.24.14 1. THREAD BREAK DETECTOR Position the thread break detector on the top of the arm, so the hole in the bracket

More information

INTELLIQUILTER INSTALLATION ON APQS MILENNIUM/FREEDOM/ULTIMATE-I VERSION

INTELLIQUILTER INSTALLATION ON APQS MILENNIUM/FREEDOM/ULTIMATE-I VERSION INTELLIQUILTER INSTALLATION ON APQS MILENNIUM/FREEDOM/ULTIMATE-I VERSION 10.18.13 If EdgeRider wheels are included in the conversion kit, install them first, following the instructions in the packaging

More information

SUPERMOTOR-V3 INSTALLATION VERSION

SUPERMOTOR-V3 INSTALLATION VERSION SUPERMOTOR-V3 INSTALLATION VERSION 09.03.14 IMPORTANT NOTE: Before starting the installation go to Utilities->Preferences and set the engagement strength for both motors to 3. 1. Remove their clear plastic

More information

TOYOTA 4RUNNER CROSS BARS Preparation

TOYOTA 4RUNNER CROSS BARS Preparation Preparation Part Number: PT78-8970 Kit Contents Front Crossbar Assembly Rear Crossbar Assembly Hardware Bag Hardware Bag Contents Rubber Stopper 4 M6 Wafer Head Screw Load Label, 60kg 4 User Manual Additional

More information

FlexJet - Flex Cable Replacement

FlexJet - Flex Cable Replacement P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer

More information

EZ-Glide Wheels Installation Patent Pending Revised 8/23/2011

EZ-Glide Wheels Installation Patent Pending Revised 8/23/2011 EZ-Glide Wheels Installation Patent Pending Revised 8/23/2011 Questions: Lakeside Quilt Co. Jack Boersma Toll Free (888) 361-4806 www.lovetoquilt.com Cell (406) 270-4715 sales@lovetoquilt.com Toll Free

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough

More information

AmTryke Adult Recumbent Model JT2000 #50-FC-2000

AmTryke Adult Recumbent Model JT2000 #50-FC-2000 AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

Hub Stands -- VERSION 5.0

Hub Stands -- VERSION 5.0 Hub Stands -- VERSION 5.0 Thanks for choosing our Alignment Hub Stands for your chassis setup needs. We hope you'll find them as handy, accurate, and easy to use as we do! Each stand has a max capacity

More information

AmTryke Adult Recumbent Model HP1000 #50-HC-1000

AmTryke Adult Recumbent Model HP1000 #50-HC-1000 AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

One- Touch Installation Instructions

One- Touch Installation Instructions One- Touch Installation Instructions 1 1 Height Adjustable Pivot w/ screws 9 Upper Work Surface 2 Rail Mount Knobs 10 Back Cover 3 Transformer 11 Center Pivot w/ screws 4 Support Legs 12 Left Monitor Arm

More information

Installation Instructions Table of Contents

Installation Instructions Table of Contents Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft

More information

INSTRUCTION MANUAL 16K - Fifth Wheel Hitch

INSTRUCTION MANUAL 16K - Fifth Wheel Hitch You can take it with you. INSTRUCTION MANUAL 16K - Fifth Wheel Hitch Product No. 30047 DEALER/INSTALLER: END USER: (1) Provide this Manual to end user. (2) Physically demonstrate hitching and unhitching

More information

Instruction Kit Gleaner K2, K3, F2, F Flow Sensor K2-F

Instruction Kit Gleaner K2, K3, F2, F Flow Sensor K2-F Parts List for Combine NOTE: Indented items indicate parts included In an assembly listed above. Quantity by Model Part Name/Description Part No. K2 F2 Instruction Kit 2005300-1 1 1 Flow Sensor K2-F2 2000292

More information

4, 6 Suspension System. Ford F250/350 4WD Part#: ,

4, 6 Suspension System. Ford F250/350 4WD Part#: , Part#: 013411, 013611 4, 6 Suspension System Ford F250/350 4WD 2005-2007 Rev. 071917 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read And Understand

More information

Prusa i3 Printer Assembly Guide

Prusa i3 Printer Assembly Guide Prusa i3 Printer Assembly Guide Special thanks to Carlos Sanchez and Miguel Sanchez for the graphics. All graphics captured from their great animation: http://www.carlos-sanchez.com/ Prusa3/ For copyright

More information

3D PRINTER. Pack 09. Anything you can imagine, you can make! 3D technology is now available for you at home! BUILD YOUR OWN

3D PRINTER. Pack 09. Anything you can imagine, you can make! 3D technology is now available for you at home! BUILD YOUR OWN BUILD YOUR OWN Pack 09 Anything you can imagine, you can make! 3D PRINTER Compatible with Windows 7 & 8 Mac OS X 3D technology is now available for you at home! www.model-space.com BUILD YOUR OWN 3D PRINTER

More information

Section 5: Parts Replacement

Section 5: Parts Replacement Section 5: Parts Replacement Should the STAR TRAC 4500 Treadmill experience a problem requiring replacement of a specific part, the following procedures will help and instruct in the replacement of major

More information

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax) INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough

More information

C15C C15C. Page 1 of 20

C15C C15C. Page 1 of 20 2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket

More information

TOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation

TOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear

More information

INSTALLATION INSTRUCTIONS CHEVY C-10 4-Link Rear End

INSTALLATION INSTRUCTIONS CHEVY C-10 4-Link Rear End INSTALLATION INSTRUCTIONS 73-87 CHEVY C-10 4-Link Rear End Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating to ensure proper

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab Diesel 2011 and newer Part Number: 75147-15 Chevy Silverado/GMC Sierra

More information

Hub Stands -- VERSION 5.0

Hub Stands -- VERSION 5.0 Hub Stands -- VERSION 5.0 Thanks for choosing our Alignment Hub Stands for your chassis setup needs. We hope you'll find them as handy, accurate, and easy to use as we do! Each stand has a max capacity

More information

Installation Instructions

Installation Instructions Installation Instructions Automatic Retracting Running Board Vehicle Application Ford F150 Supercrew 2001-2003 (2004 Heritage) Part Number: 75111-01 www.bestop.com - We re here to help! Visit our web site

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0921 APPLICATION 2007-08 E92 335i/xi without stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler

More information

MF 9690, 9790, Challenger 660, 670

MF 9690, 9790, Challenger 660, 670 Ag Leader Technology Parts List Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. MF 9690 MF 9790 Challenger 660 Challenger 670 Instruction

More information

License Plate Bracket (4) Rubber Plugs. (2) Retaining Rings (2) Foam Spacers

License Plate Bracket (4) Rubber Plugs. (2) Retaining Rings (2) Foam Spacers LDB-NTIT62-FB PARTS LIST: 1 LD1 Bumper Assembly 2 8mm Hex Nuts 1 Driver/left L Bracket (center LED light) 2 6mm x 20mm Button Head Bolts 1 Passenger/right L Bracket (center LED light) 4 6mm x 18mm x 1.6mm

More information

Ford Super Duty Recoil Traction Bar System. Part#: ,123409

Ford Super Duty Recoil Traction Bar System. Part#: ,123409 Part#: 123418,123409 Ford Super Duty Recoil Traction Bar System Rev. 011017 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail: tech-bds@sporttruckusainc.com

More information

BX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler

BX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler Operator Manual & Installation Instructions ALLURE Tow Bar (10,000 lb) Pintle Coupler Hooking Up to Towed Vehicle 1. Position the towing vehicle on a level surface with a straight driveway ahead and engage

More information

Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.

Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore

More information

LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation

LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated

More information

SCdefault. 900 Installation instructions

SCdefault. 900 Installation instructions SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0924 APPLICATION: 2011-12 E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler Congratulations for being selective enough

More information

STEERING SYSTEM - MANUAL RACK & PINION

STEERING SYSTEM - MANUAL RACK & PINION STEERING SYSTEM - MANUAL RACK & PINION 1993 Nissan Sentra 1993 STEERING Nissan Manual Rack & Pinion NX, Sentra DESCRIPTION & OPERATION Steering gear assembly is a manual rack and pinion type. Unit is mounted

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram 1500 Crew Cab 2009 - Current : 75138-15 Dodge Ram 2500/3500 & HD Crew Cab 2010 - Current : 75138-15

More information

Installation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino

Installation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in

More information

2011+ Adjustable Tie-rod Ends (Mm5TR-2)

2011+ Adjustable Tie-rod Ends (Mm5TR-2) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2011+ Adjustable Tie-rod Ends (Mm5TR-2) Instructions 1. Set the parking brake

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Ford Super Duty F-250/350/450 Crew Cab 2008 and newer Part Number: 75134-15 www.bestop.com - We re here to help!

More information

Loose Parts Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts Note: Determine the left and right sides of the machine from the normal operating position. Brake Kit Dingo TX 0 & Compact Utility Loader Part No. 0 0 & 0 Loose Parts Note: Determine the left and right sides of the machine from the normal operating position. Description Qty. Use Drive wheel Brake

More information

Z-Gate Universal Shifter

Z-Gate Universal Shifter Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum

More information

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before

More information

Setup, Assembly, & Adjustment

Setup, Assembly, & Adjustment Setup, Assembly, & Adjustment 34877 Rev. B 1 of 8 Melco Fast Clamp Instructions The Melco Fast Clamp is a versatile clamping system for your embroidery machine. This document will walk you through the

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92/E93 335i/xi with stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92/E93 335i/xi with stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0920 APPLICATION 2007-10 E92/E93 335i/xi with stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY TRUTRACK TRUNNION BAR WEIGHT DISTRIBUTION SYSTEM MAINTENANCE Keep the socket-mounted ends of the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REAR SPOILER Application 2011 CR-Z MUGEN Publications No. AII 45919 Issue Date APRIL 2011 PARTS LIST Right wing bracket Rear wing Left wing bracket Right wing base Right

More information

Stowe Cargo Management System

Stowe Cargo Management System Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages

More information

4 Radius Arm Suspension System. Dodge Ram WD Power Wagon Part#:

4 Radius Arm Suspension System. Dodge Ram WD Power Wagon Part#: Part#: 012402 4 Radius Arm Suspension System Dodge Ram 2500 4WD Power Wagon 2014-18 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web: www.bds-suspension.com. E-mail: tech-bds@sporttruckusa.com

More information

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:

More information

2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw

2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8 pilot drill 1-3/4 Hole saw 2 Hole saw 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill

More information

***Be sure that the loaded trailer weight does not exceed 24,000 lbs. or the vertical load rating does not exceed 6000 lbs.

***Be sure that the loaded trailer weight does not exceed 24,000 lbs. or the vertical load rating does not exceed 6000 lbs. April 2006 INSTALLATION INSTRUCTIONS MODEL NO. 70680 07068 24K 5th Wheel with Heavy Duty EZ-ROLLER For use on shortbed P/U applications US Pat. No. 6247720 PARTS INCLUDE: 1. 1675-07 Head Assembly (1) 15.

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

4 & 6 4-Link Suspension Systems. Ford Super Duty 4WD Part#: ,

4 & 6 4-Link Suspension Systems. Ford Super Duty 4WD Part#: , Part#: 013013, 013014 4 & 6 4-Link Suspension Systems Ford Super Duty 4WD 2011-2016 Rev. 051817 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Ford F150 Super Crew Cab 2009 Current : 75141-15 www.bestop.com - We re here to help! Visit our web site and

More information

INSTALLATION INSTRUCTIONS Air Spring Kit Ford F-150 4WD IMPORTANT NOTES

INSTALLATION INSTRUCTIONS Air Spring Kit Ford F-150 4WD IMPORTANT NOTES INSTALLATION INSTRUCTIONS 6154 Air Spring Kit 2004+ Ford F-150 4WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY BEFORE STARTING YOUR INSTALLATION IMPORTANT

More information

Read and understand all instructions and warnings prior to installation of system and operation of vehicle.

Read and understand all instructions and warnings prior to installation of system and operation of vehicle. 491 W. Garfield Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech@bds-suspension.com Part#: 023624 Product: 4 & 6" Suspension System Application: 2009-2013

More information

SCION tc STRUT TIE BAR Preparation

SCION tc STRUT TIE BAR Preparation SCION tc 2005 - STRUT TIE BAR Preparation Part Number: 00016-80440 Code: YY1 Kit Contents 1 1 DS Mount Plate 2 1 PS Mount Plate 3 1 Cross Bar 4 1 Hardware Bag Hardware Bag Contents 1 4 8mm Screws 2 4 8mm

More information

2015 Ford F150 Front Bumper w/ LED

2015 Ford F150 Front Bumper w/ LED PARTS LIST: 2015 Ford F150 Bumper w/ LED 1 Bumper Assembly 4 8mm Lock Washers 1 Driver/left L Bracket (center LED light) 2 8mm Hex Nuts 1 Passenger/right L Bracket (center LED light) 2 6mm x 20mm Button

More information

Installation Guide. Stowe Cargo Management System. Table of Contents

Installation Guide. Stowe Cargo Management System. Table of Contents Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

LD1 FRONT BUMPER GMC SIERRA 1500

LD1 FRONT BUMPER GMC SIERRA 1500 LDB-GSIE52-FB PARTS LIST: 1 LD1 Bumper Assembly 6 12mm Lock Washers 1 Driver/left Frame Mounting Bracket 6 12mm Hex Nuts 1 Passenger/right Frame Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Tow Hook

More information

Photo 1. Shift pattern gate plate

Photo 1. Shift pattern gate plate Installation Instructions MAGNUM GRIP STREET BANDIT SHIFTER Fits: GM, Chrysler, and Ford Automatic Transmissions See Application Guide for Specific Vehicles Catalog # 81050 WORK SAFELY! For maximum safety,

More information

(Refer to qualified personnel)

(Refer to qualified personnel) 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm (Slide-Above-Arm Configuration)

More information

Ford Super Duty Recoil Traction Bar System. Part#: ,

Ford Super Duty Recoil Traction Bar System. Part#: , Part#: 123408, 123409 Ford Super Duty Recoil Traction Bar System Rev. 090817 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read And Understand All

More information

FITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No )

FITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No ) ARB WINCH / NON WINCH BULL BAR TO SUIT LANDROVER DISCOVERY 2003 ONWARD. FITTING KIT No s :- 617 1793 BULL BAR WINCH ( P/No 343 2120 ) 617 1794 BULL BAR NON WINCH ( P/No 323 2120 ) WARNING FOR VEHICLES

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. S 1998 CIVIC 2/3/4-DOOR All 18767 Issue Date SEP 1997 PARTS LIST Fog Light Kit: P/N 08V31-S01-100 Right fog light (marked R ) Fuse label

More information

2. Remove front wheels.

2. Remove front wheels. 1 PARTS DIAGRAM 2 Installation Instructions: (PASSENGER SIDE) 1. Place jack under center of RUV front end and lift until front wheels clear the ground. Be careful to support the RUV properly so that it

More information

5.5 Gas & 6 Diesel Radius Arm Suspension System. Dodge Ram WD Pickup Dodge Ram WD Pickup

5.5 Gas & 6 Diesel Radius Arm Suspension System. Dodge Ram WD Pickup Dodge Ram WD Pickup Part#: 012610 5.5 Gas & 6 Diesel Radius Arm Suspension System Dodge Ram 3500 4WD Pickup 2013-17 Dodge Ram 2500 4WD Pickup 2014-17 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web: www.bds-suspension.com.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket

More information

w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required

w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required -J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.

More information

Type 2 Push-Through 37 Ton Log Splitter. Assembly Manual

Type 2 Push-Through 37 Ton Log Splitter. Assembly Manual Type 2 Push-Through 37 Ton Log Splitter Assembly Manual Refer to this manual for the following models: RS37PT-LF09PC-16-1 RS37PT-LF09EC-16-1 RS37PT-LF09EC-16-2 RS37PT-LF13EC-22-1 RS37PT-LF13EC-22-2 RS37PT-LF15EC-22-1

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 23086 SYSTEM CR-V Issue Date NOV 2001 PARTS LIST Security System P/N 08E51-EP4-100 Security System Attachment P/N 08E55-S9A-100 Security

More information

HD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:

HD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST: PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for

More information

PRODUCT INFORMATION BULLETIN #3365 DIGITAL MOTOR CONTROL PLATTER SYSTEMS For Serial Number and After

PRODUCT INFORMATION BULLETIN #3365 DIGITAL MOTOR CONTROL PLATTER SYSTEMS For Serial Number and After PRODUCT INFORMATION BULLETIN #3365 DIGITAL MOTOR CONTROL PLATTER SYSTEMS For Serial Number 28640996 and After Record Platter System Identification Numbers Here: Model # Serial # Table of Contents Program

More information

TCI FastGate Shifter Installation Instructions

TCI FastGate Shifter Installation Instructions 151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING

INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, 76250 Application: 08-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make informed

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to

More information

2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions

2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions 2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set

More information

FlexJet Carriage Circuit Board (PCB) Replacement

FlexJet Carriage Circuit Board (PCB) Replacement P/N: 111484 R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 ioline.com FlexJet Carriage Circuit Board (PCB) Replacement Notices: Warning! Ensure that all AC power cables

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC

More information

A B C D E F. Tools Required (supplied by others)

A B C D E F. Tools Required (supplied by others) Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)

More information

2017 Current Ford Raptor Bump Stop Kit Installation Instructions

2017 Current Ford Raptor Bump Stop Kit Installation Instructions 2017 Current Ford Raptor Bump Stop Kit Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend

More information

M Damper Mount Linkage Kit Installation. Item Description Quantity Item Description Quantity Nuts 2

M Damper Mount Linkage Kit Installation. Item Description Quantity Item Description Quantity Nuts 2 FANs 268.1, 1628.3 Installation Bulletin M9000-150 Issue Date 0796 M9000-150 Damper Mount Linkage Kit Installation 21 18 19 20 2 22 17 2 4 3 2 15.5 393.7 1 17 16 15 11 13 12 8 9 10 2 5 Note: Damper mount

More information

ASSEMBLY MANUAL. 45-Foot Air Double Disc Drill. Amity Technology, LLC th Avenue North Fargo, ND (701)

ASSEMBLY MANUAL. 45-Foot Air Double Disc Drill. Amity Technology, LLC th Avenue North Fargo, ND (701) ASSEMBLY MANUAL 45-Foot Air Double Disc Drill Amity Technology, LLC 2800 7th Avenue North Fargo, ND 58102 (701) 232-4199 www.amitytech.com TABLE OF CONTENTS Main Frame 1 Wing Lock Towers 3 Wing Frames

More information

PREMIUM FRONT BUMPER FOR RAM 2500/3500. AEV30239AJ Last Updated: 09/05/17 INSTALLATION GUIDE

PREMIUM FRONT BUMPER FOR RAM 2500/3500. AEV30239AJ Last Updated: 09/05/17 INSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM 2500/3500 AEV30239AJ Last Updated: 09/05/17 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS THOROUGHLY

More information

E-LIFT II+ SYSTEM WITH SPRING LEVER FOR A-SERIES AND FULL FRAME LOOMS

E-LIFT II+ SYSTEM WITH SPRING LEVER FOR A-SERIES AND FULL FRAME LOOMS Congratulations on your purchase of the E-Lift II+ system. This system replaces the action of treadling, eliminating leg strain and fatigue. When you activate the Foot Switch, the motor turns, and selected

More information

STOP---READ THIS FIRST!

STOP---READ THIS FIRST! STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2011-13 FORD F-250 & F350 6 & 8 LIFT KITS 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196 (559) 277-0457 FAX www.mcgaughys.com

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

PARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F

PARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24307 SYSTEM 2003 ELEMENT Issue Date DEC 2002 NOTE: An optional keyless entry system (sold seperately) must be installed before you

More information

D40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws

D40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws HINGE # 1017 2 x Support Plate 1018 8 x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws 2 x Lid mount gas strut bracket 1041 2 x Self tap strut mount 1040 1 x Central Lock bracket 1510

More information

Current Range Rover Sport STRUT Collection Installation Manual

Current Range Rover Sport STRUT Collection Installation Manual 2014 - Current Range Rover Sport STRUT Collection Installation Manual 1 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille

More information

ECO-SERIES FRONT BUMPER FOR GM SIERRA #GM-19337

ECO-SERIES FRONT BUMPER FOR GM SIERRA #GM-19337 #GM-19337 Body Armor 4x4 272 Corporate Terrace St. Corona, CA 92879 951-808-0750 Customer Service hours: M-TH: 7:30am to 4:30 PM Pacific Time Friday: 8 AM Noon Pacific Time PARTS LIST: 1 LD1 Bumper Assembly

More information

Installation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY

Installation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY Installation Instructions 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500 P/U ONLY 2007-13 GM 1500 Truck Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500

More information