9-1. Accessories & Options. Fire Suppression System, Chassis. Rev: 07/2016 FF Page 1 of

Transcription

1 Accessories & Options -1 Fire Suppression System, Chassis Rev: 07/20 FF Page 1 of 7

2 Item Part No. Qty Description Item Part No. Qty Description Fire Suppression System - Chassis Tank, LVS Chemical, Fire Suppr Manifold Block Kit, Nozzle Actuator Cartridge, Nitrogen 7 R Fitting Lockwasher Elbow, Pipe Fitting Fitting Relief Valve R811. Locknut Tee, Pipe Fitting Grommet Clip, Insul Fitting W 17. Hard Washer R Clip, Insul R Clip, Insul '. Trim, Edge W 1. Washer 1 R8 2. Capscrew Clamp W. Washer 3 220W. Capscrew R812. Lockwasher Stud, Weld 70 YHGB 0 '. Hose Guard, Plastic Spiral Fitting Elbow, Pipe Control Module, Interface Actuator Cable Tie Weldment, Actuator Battery Connector, Tee Cable, Drop Actuation Device, Protracting Fused Power Circuit Cable Cable Assembly, Relay Circuit 8 R Locknut 8 R83. Capscrew Fitting Fitting Bracket Elbow, Pipe Valve, Cartridge Valve, Cartridge Clamp Fitting Connector, Tee R80 1. Clip, Insul Cable, Detection Mount, Tack Cable Tie, Double Loop Cable, Release Cable, Display Sleeve, Rubber Cable, Detection Cable, Linear Detector Connector, Eol Divice 8701 '. Loom, Wire RL. Tape 7 Y27E-1. Washer Cap, Blow-Off 221W 1. Capscrew Assembly, Cable Cable, Linear Detector 2 SHM Shim, Brg Air Cleaner Fitting Kit, Hose Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Hose Assembly Fire Suppression System should be serviced by an authorized ANSUL service technician. Page 2 of 7 FF Rev: 07/20

3 NOTES: 1. ITEMS 70,,,7, & 8 ARE NOT SHOWN. ITEM 8 COMES WITH NOZZLE KIT. ITEM 70 IS TO BE USED WHEN PASSING HOSE THROUGH OR AROUND ANY SHARP EDGES OF A DECK OR BULKHEAD. ITEM IS TO BE USED WHEN PASSING CHECKFRE WIRES THROUGH OR AROUND ANY SHARP EDGES OF A DECK OR BULKHEAD. THE USE OF ITEM IS TO BE USED ON ALL THREADED PIPE CONNECTIONS. DO NOT ALLOW TAPE INSIDE OF CONNECTION. THE USE OF LIQUID SEALANTS IS NOT APPROVED BY ANSUL. ITEM 7 IS TO BE USED AS REQUIRED TO ENSURE A TIGHT CONNECTION WHEN ATTACHING FITTINGS TO NOZZLE BRACKET. W 2. ANSUL RECOMMENDS THE FOLLOWING MINIMUM BEND RADII FOR PARKER 2 SERIES HOSES. # IN, # IN, # IN. ALL ANSUL CABLES HAVE A MINIMUM BEND RADIUS OF 2. INCHES. 3 WHEN FILLING TANK USE A FUNNEL AND LONG HOSE THAT REACHES BOTTOM OF TANK TO PREVENT SLOSHING OF LIQUID FOAM AGENT. THE CHEMICAL FOAM BUBBLES MAY TAKE DAYS TO DISSIPATE WHEN AGITATED. DO NOT INSTALL ITEM 80, THIS WILL ARM FIRE SUPPRESSION SYSTEM. THE ADDITION OF POWER BY ITEM 77 (BATTERY) OR 81 (POWER CABLE) WILL ACTIVATE SYSTEM FOR NORMAL DUTY. BAG ITEMS 77 & 80 IN A BAG LABELED FIRE SYS ACTIVIATION AND SECURE IN CAB TO DISPLAY UNIT WIRING WITH CABLE TIE. ITEM 2 IS USED TO STOW EXTRA CABLES, BY COILING WIRES AND STRAPPING IN PLACE. ALL ANSUL CABLE HAVE A MINIMUM BEND RADIUS OF 2. INCHES. X 3P 3P FOR BRAKE ACCUMULATOR PURGE SYSTEM INSTALL BEFORE SHIPPING TO FINAL CUSTOMER. REMOVE EXISITNG BRAKE ACCUMULTOR DRAIN VALVE AND INSTALL ITEMS 0 & 1. TORQUE ITEM 37 TO 30-3 FT LBS, THEN INSTALL ITEM 38 TO 20-2 FT-LBS. V V Q 3M 3N 3N Q X 3M Rev: 07/20 FF Page 3 of 7

4 DETAIL 2A TYP SINGLE NOZZLE MIDDLE OF LINE W/ 0 ELBOW ARRGT E DETAIL 2B TYP SINGLE NOZZLE ARRGT D 2A 2B C F T G S DETAIL 2C TYP MIDDLE OF LINE ARRGT R L 2D M DETAIL 2D TYP DOUBLE NOZZLE END OF LINE ARRGT V J H 2E X 2 3 U N 2F P X 2J 2H 2G A B 22 BATTERY DISSCONNECT Q 8 K 0 1 TO CAB DETAIL 2E TYP DOUBLE NOZZEL MIDDLE OF RUN W/ 0 ELBOW ARRGT 22 DETAIL 2J ICM INSTALL BRAKE ACC PURGE 88 DETAIL 2G TYP SINGLE NOZZLE MIDDLE OF LINE DETAIL 2F TYP DOUBLE NOZZLE END OF LINE ARRGT 2 W/ ELBOW ARRGT 2 DETAIL 2H PNEUMATIC ACCS DRIVER Rev: 07/20 FF Page of 7

5 K SECTION 3K-3K 3K 1. P N V U 1.7 3L 1. DETAIL 3L () PLACES SECTION 3M-3M 1. FRONT 1 LOOP END LEG LEFT X 1. SECTION 3P-3P FRONT CAB LOOP ABOVE TRANSMISSION LOOP START POINT X SECTION 3N-3N CAB DETECTION LOOP Rev: 07/20 FF Page of 7

6 0 FIRE SYSTEM CONDUIT PASS THROUGH R 1.12 T DETAIL R BRAKE ACC PURGE VALVE X 2 20 K Q B 2 A T U SECTION Q-Q SHARES HARDWARE LVS 30 TANK 78 EMA PNEUMATIC ACCS DRIVER 7 1 CAB LOOP ZTR HOOK UP 82 2 HOOD S 8 0 X X 7 DETAIL S SECTION T-T 81 ATTACH TO BATTERY DISCONNECT SWITCH DETAIL U DISTRIBUITION MANIFOLD 3 Rev: 07/20 FF Page of 7

7 2 X FRONT H J L M F G 1. S 1. R 1. X DETAIL W CAB LOOP TERMINATION ON DECK E 2 1. D 1.7 C 1. T 2 X TYP SPACING LEFT EMA SECTION V-V HOOD ROUTING FOR DISTRIBUTION AND DETECTION BATTERY DISCONNECT VIEW X-X RIGHT REAR BUMPER BOX Rev: 07/20 FF Page 7 of 7