In This Section. Metal Framing, Pipe Hangers and Accessories. Superstrut Metal Framing, Pipe Hangers and Accessories D-1

Transcription

1 In This Section Superstrut Metal Framing Channels Overview...D-2 D- Threaded Products and Hardware...D-8 D- Fittings and Brackets...D-4 D-2 Concrete Inserts...D-22 D-2 Beam Clamps...D-24 D-2 Pipe Straps, Conduit Clamps and Hangers...D- D-9 Surface Raceway and Lighting Systems...D-80 D-84 Special Metals...D-85 D-94 Slotted ngle Metal Framing...D-95 D-96 Metal Framing Engineering Data...D-9 D-9 D-

2 Metal Framing Channels Overview New Trivalent Galv-Krom Finish Is RoHS Compliant Thomas & Betts is proud to introduce the new and improved Trivalent Galv-Krom finish. Galv-Krom finish is a combination of.5 mils electro-plated Zinc and a gold Trivalent Chromium finish. Gold Trivalent Chromium Finish The new Galv-Krom finish features a Trivalent Chromium formulation that provides all the features and protection of Hexavalent Chromium (CR VI) without the use of this chemical compound. Hexavalent Chromium is restricted by some standards such as the European Union directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS). RoHS Compliant One great feature for the new Trivalent Chromium formulation is RoHS compliance. Because Hexavalent Chromium is a substance that is restricted by RoHS, moving away from a Hexavalent formulation to the new Trivalent formulation will make the performance of Galv-Krom coating available to customers affected by RoHS and other standards like RoHS around the world. Trivalent Galv-Krom Finish Is OSH Safe The Hexavalent formulation of the Galv-Krom finish is safe with regard to the revised 2006 OSH standard. This new Trivalent formulation of the Galv-Krom finish does not contain any Hexavalent Chromium and therefore does not fall under the scope of the OSH standard at all. s a result, the new Trivalent Galv-Krom finish, just like the Hexavalent Galv-Krom finish, is OSH compliant. STM B6 Specification The improved Galv-Krom finish is applied in compliance with STM B6 coating, the same standard as used previously. This standard outlines electro-deposited coatings of zinc on steel. D-2

3 Metal Framing Channels Overview Finishes GoldGalv The standard GoldGalv finish is made up of a multi-step electrogalvanizing and zinc dichromate process. The trivalent Chromium finish is applied over the zinc, producing a chemically bonded non-porous barrier for protection from moisture and air. The.5 mil electro-plated zinc and gold trivalent Chromium finish provide all of the features and protection of hexavalent Chromium without the use of the chemical. Green or White Urethane Powder Coated (Suffix GR or WH) Urethane powder resins are applied electrostatically to the steel after fabrication. Once the material is completely covered with the powder-form urethane, it proceeds through a 400 baking process for ten minutes, creating a chemical bond. This results in a minimum of.5 mil thickness of urethane coating, providing excellent resistance to chipping or peeling. Pregalvanized (Suffix PG) zinc coating is applied by hot-dipping the steel coil at the mill prior to fabrication. Once the material is worked by roll-forming, cutting or punching, minimal protection is provided for raw edges. This weakness is typical with precoated material and affects the channel section around holes, extreme ends and the edges of the U shape lips. Superstrut pregalvanized material is in conformance with STM -525/G-90 specification standards, representing 0.90 ounces of zinc per square foot of steel. This finish is often referred to as hot-dipped mill galvanized or mill galvanized. Hot-Dipped Galvanized (Suffix HDG) The material is zinc coated after fabrication, providing total product protection on all surfaces. The fabricated channel or fitting is suspended and then dipped into tanks of hot zinc for a prolonged period, creating a coherent bond. The result is superior corrosion resistance as compared to pre galvanized material. Hot-dipped galvanizing is not recommended for threaded products, considering the zinc coating thickness will often disrupt the threads. Superstrut hot-dipped galvanized is in conformance with STM Specifications -2 (formerly -86) and -5. Superstrut channels maintain a minimum.5 ounces of zinc per square foot of steel or 2.5 mils (STM -2, Thickness Grade 65). This finish is also referred to as hot-dipped galvanized after fabrication. SilverGalv (Suffix EG) Often referred to as zinc plated or electroplated zinc, the steel and.5 mils of zinc are bonded by an electrolysis process. This is the identical process used in the Kindorf Galv-Krom finish without the numerous benefits of the gold colored trivalent chromium conversion coat (see Galv-Krom finish for more information). Electrogalvanizing is most commonly applied to small fittings, hardware and threaded products. PVC Coated (Suffix PVC) polyvinyl chloride (PVC) plastic coating is fused to the channel, fitting or accessory after fabrication by immersing the part in fluidized PVC tanks. The fused-melt mixed powder PVC coating thickness is 5 mils (.05") plus or minus five mils. PVC material is a thermoplastic and will soften in high temperature. n inherent weakness with PVC coatings occurs when field alterations are applied, such as cutting or drilling. These acts disrupt the sealed PVC product and warrant field touch-up. Thomas & Betts cannot be held responsible for field-altered PVC coated products. Copper Plated ( T inserted as the second digit of the part number; Example: CTL-0-2) Plain steel proceeds through a series of rinse tanks to clean the material surface. Once cleaned, the fabricated part is etched by dipping into an acid pickle bath to prepare the surface for adhesion. Copper is electrically applied by submerging in a copper bath. To seal the finish, the product continues to a sealer tank and is then dried by forced hot air. Black (Suffix B) black finish is raw steel with only a light oil finish as supplied by the steel manufacturer. There is no protection against red rust. Stainless Steel (Suffix SS) Superstrut channel is supplied in type 04 stainless steel when required. Type 6 stainless steel may be available upon request. luminum (Suffix L) Superstrut channel and hardware are available in aluminum. Warning: Load tables, charts and design criteria provided in this catalog are intended as guides only. Selection of proper product, installation intervals, erection and placement are the responsibility of the user. Superstrut products are intended to be used for the support and bracing of fixtures, cable, pipe and conduit. Improper use or installation may result in injury to persons or damage of property. Material and finish specifications are subject to change without notice. D-

4 Metal Framing Channels Overview Finishes (continued) GoldGalv Soak Degreasing Chemical solution removes bulk of oil and grease buildup. Formed Hot Rolled Steel Electro-Plated Zinc Coating Yellow Dichromate Conversion Coat Electro Cleaner The metal is negatively charged to remove minute surface particles. Rinse Live, clear water rinse. The standard GoldGalv finish is made up of a multi-step electrogalvanizing and zinc dichromate process. The trivalent Chromium finish is applied over the zinc, producing a chemically bonded non-porous barrier for protection from moisture and air. The.5 mil electro-plated zinc and gold trivalent Chromium finish provide all of the features and protection of hexavalent Chromium without the use of the chemical. (Refer to page D-5 for more details). Sulfuric cid Bath Prepares the metal by etching the surface for the zinc application. Rinse Live, clear water rinse. Zinc Tank Electrically applies the zinc metal coating. Rinse Chemically treated rinse water. Rinse Live, clear water rinse. Rinse Live, clear water rinse. Chromate Dip yellow dichromate conversion coat is applied to the zinc. Rinse Live, clear water rinse. Dryer Hot air is forced around strut until dry. D-4

5 Metal Framing Channels Overview Finishes (continued) SilverGalv Electro-Galvanized Finish From Superstrut Protection is the name of the game and SilverGalv delivers a winning combination of features designed to meet the most exacting specifications. SilverGalv offers the ultimate in corrosion protection versatility and performance, including Strong brasion Resistance SilverGalv provides strong abrasion resistance, even under extreme conditions, thanks to its unique zinc finish and chromate barrier. The green paint finishes typically used for strut cannot compare to this level of protection Clean Finish SilverGalv ensures a finished product that leaves no residue on your hands. In the SilverGalv process, a zinc finish is applied after fabrication. s a result, all the oil and grime that accumulates during manufacturing gets thoroughly cleaned off during the plating process Paintable Surface pplying SilverGalv after fabrication provides the end user with a clean, smooth surface to paint Interchangeable Silver Color SilverGalv s silver hue means it can be used interchangeably with either standard pre-galvanized channel systems or silver colored fittings commonly used with green painted strut systems No More White Rust With pre-galvanized strut, white rust frequently taints the zinc finish. With SilverGalv, this problem is eliminated thanks to a clear chromate applied over the zinc that stops white rust from forming Standard Channels Material Channels are cold formed from hot-rolled pickled and oiled strip steel. Material Thickness ll Series gauge material ll Series gauge material Punched Holes and Cut Ends are Protected Unlike a pre-galvanized finish where steel holes and cuts have no corrosion protection, Silver-Galv protects every portion of the strut. Because SilverGalv s finish is applied after fabrication, all punched holes and cut ends share a consistent quality with the rest of the material Salt Spray Hours Industry Enamel Green Metal Framing Channel Finish Corrosion Resistant Testing, STM B Epoxy Green Industry Pre-Galvanized G90 SilverGalv SilverGalv provides more corrosion protection than Pre-Galvanized or Green Painted finishes. New Trivalent GoldGalv Standard Lengths Standard lengths for channel are 0 ft. and 20 ft. Standard length tolerance ± 8". Shorter lengths are available at a small cutting charge. GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by gold colored zinc dichromate to give excellent corrosion resistance and superior paint base. See page D-4 for a complete description of the GoldGalv hardware finish. GoldGalv hardware will be furnished if no other finish is specified Series B Series C Series E Series H Series 4 D-5

6 Metal Framing Channels Overview Channel available in Solid, Half Slot, Punched, Slotted and Knockout configurations. Wt./Ft..90 lbs ga E-200 Channel available in Solid, Half Slot and Punched configurations. Wt./Ft. 2.4 lbs B-200 Channel available in Solid, Half Slot, Punched and Slotted configurations. Wt./Ft..28 lbs ga H-200 Channel available in Solid, Half Slot and Punched configurations. Wt./Ft..05 lbs. 6 2 ga C-200 Channel available in Solid, Half Slot and Punched configurations. Wt./Ft..0 lbs Channel available in Solid, Half Slot, Punched, Slotted and Knockout configurations. Wt./Ft..40 lbs B-400 Channel available in Solid, Half Slot, Punched and Slotted configurations. Wt./Ft lbs. D-6

7 Metal Framing Channels Overview Superstrut Channels Welding Combinations ll Superstrut Channels are available in a variety of combinations some are shown here. Multiple channels are spot welded on " centers. 2* 2-2-B 2-C -C How to Order - -B 0 and 20 ft. lengths steel. Special lengths may be ordered. Replace the last digits of the regular channel catalog number with the designation of the desired combination. EXMPLES: Two -200 channels back to back are ordered as Two -200 channels back to side are ordered as -202-C. Specify desired finish or material. * and B Series back-to-back combinations are joined using Thomas & Betts steel rivet joining process. The riveted channel is offered in standard GoldGalv, stainless steel, painted, pre-galvanized and hot-dip galvanized finishes. -D 4 Hole Configurations Half Slot Channel STD. CT. NO. DIM. (IN.) G. CTN HS 5 8 x * B-200-HS 5 8 x 6 2 * C-200-HS 5 8 x E-200-HS 5 8 x H-200-HS 5 8 x 4 2 * -400-HS 5 8 x * B-400-HS 5 8 x " x 8" slots on 2" centers. * Standard lengths 0 ft. and 20 ft. for standard cartons. Please consult your local T&B representative. Slotted Channel STD. CT. NO. DIM. (IN.) G. CTN S 5 8 x * B-200-S 5 8 x 6 2 * -400-S 5 8 x * B-400-S 5 8 x 6 4 * 6" x " slots on 4" centers. * Standard lengths 0 ft. and 20 ft. for standard carton. Please consult your local T&B representative. Punched Channel 2" 8" STD. CT. NO. DIM. (IN.) G. CTN P 5 8 x B-200-P 5 8 x H-200-P 5 8 x P 5 8 x B-400-P 5 8 x " holes on 8" centers. vailable in 0 & 20 ft. lengths. Channel with Knockouts STD. CT. NO. DIM. (IN.) G. CTN KO 5 8 x * -400-KO 5 8 x * KO for 2" conduit. Please consult your local T&B representative. Standard Finish GoldGalv brand. 4" 6" D-

8 Threaded Products & Hardware Trapnut Strut Fastener Features and Benefits The unique scissor action of the Trapnut Strut Fastener closes at any desired position on the threaded rod. Once closed, precision threads trap the threaded rod for a sturdy hold that can be adjusted up or down for fine-tune positioning. While the versatile Trapnut has a locking pin that holds it in the desired position, it can also be removed and reused. Standard method using nuts and washers. New method using Trapnut Strut Fastener. Unlike a hex nut, there is no need to thread the Trapnut from either end of the rod, saving valuable time on the job. While the Trapnut Strut Fastener is a time-saver for new construction, it is invaluable for retro-fit applications. Rather than disassembling an existing trapeze to run additional conduit above it, the Trapnut fastener can be clamped between the existing trapeze and the beam clamp for a speedy retro-fit solution. It s ideal for applications where the rod ends are not accessible. The Trapnut fastener has a sturdy steel construction that is load bearing, so you can be confident of a solid installation. nd, the Trapnut fastener functions as a hex nut, square washer and flat washer combined, so there are fewer parts to keep up with on the job. H 22 8 Trapnut Strut Fastener Galv-Krom H 22 8 EG Trapnut Strut Fastener SilverGalv Easy to Install 2 Hold in the open position. No need to thread the Trapnut fastener from either end of the rod saving valuable time Perfect for retro-fit applications where the rod ends are not accessible Insert the bottom plate on the rod and close the top plate. Precision threads trap the threaded rod for a sturdy hold that can be adjusted up or down for fine-tune positioning Functions as a hex nut, square washer and flat washer combined SIZE DESIGN STD. CT. NO. DESCRIPTION (IN.) LOD LBS. CTN. H 22 /4 4" Galv-Krom H 22 /8 8" Galv-Krom H 22 /2 2" Galv-Krom 2, H 22 /4 EG 4" SilverGalv H 22 /8 EG 8" SilverGalv H 22 /2 EG 2" SilverGalv 2, H 22 /4 SS6 4" Type 6 Stainless Steel H 22 /8 SS6 8" Type 6 Stainless Steel H 22 /2 SS6 2" Type 6 Stainless Steel 2, Press the pin with pliers. Locking pin holds it in the desired position Can be removed and reused Tighten to the desired position with pliers. Can be adjusted up or down for fine-tuned positioning Sturdy steel construction that is load bearing Sized to provide custom fit for either 5 8" or 2" strut systems D-8

9 Threaded Products & Hardware Easily installs above existing trapeze. Handle Retro-Fit Trapeze pplications with Ease! Trap-Eze Connector Can be used to extend existing trapeze. View window provides strut length safety zone for rough cuts versus precision cuts. Unique safety slot maintains bracket position on threaded rod and prevents disengagement of the trapeze system. Designed for use with the innovative Trapnut Strut Fastener. The innovative Trap-Eze Connector changes a time-consuming retro-fit trapeze application into a streamlined process. Using a Trapnut Strut Fastener, the new Trap-Eze Connector can be easily installed above or to the side of an existing assembly, eliminating the need to disassemble and reassemble the trapeze. It is designed for use with shorter strut lengths that can vary in length by as much as an inch, so the strut can be rough cut versus labor-intense precision cuts. Easily installs above or to the side of an existing assembly, eliminating the need to disassemble and reassemble the trapeze Connectors can be reused upon disassembly of a trapeze Designed for either 8" and 2" threaded rod Designed for use with the innovative Trapnut Strut Fastener, which can take up to 4% less time than standard nuts and washers on retro-fit trapeze applications View window provides safety zone for strut length STD. CT. NO. DESCRIPTION CTN. For 2 Strut B998 Trap-Eze End Connector Gold-Galv 20 B999 Trap-Eze Mid Connector Gold-Galv 0 B998EG Trap-Eze End Connector EG 20 B999EG Trap-Eze Mid Connector EG 0 Square Washer Located Square Washer B-24 BOLT STD. CT. NO. SIZE (IN.) CTN. B-24-/ B-24-5/ B-24-/ B-24-/ B-24-5/ B-24-/ B-24L BOLT STD. CT. NO. SIZE (IN.) CTN. B-24L-/ B-24L-5/ B-24L-/ B-24L-/ B-24L-5/ D-9

10 Threaded Products & Hardware Channel Nuts Superstrut channel nuts are manufactured from mild steel and are case hardened. Design Data Superstrut self-aligning channel nuts are designed to provide resistance to pull out and resistance to side slip in excess of the full strength of the channels with which they are used. The extreme resistance to side slip results from the unique design of the alternate teeth, spaced and designed to develop a wedging action that increases with pressure or load. Load Ratings for 4", 8" and 2" Strut Nuts used in Superstrut CHNNEL NUT SLIP TEST PULL TEST SIZES (IN.) RTING RTING ,000 2,200 2,000 If connections will be subjected to dynamic or seismic loading conditions, contact the factory for design assistance.. ll ratings have safety factor of applied. 2. Load ratings are for Static pplications. UC-00 Universal Cone Nut Eliminates the inventory and installation hassles of conventional spring nuts. Fits all 5 8" channel, regardless of depth, with a simple twist of your thumb. Pliable nylon cone secures the nut in place through the entire range of construction site temperatures. Screw Threads THRED SIZE (IN.) THREDS PER INCH DESIGN TORQUE (FT. LBS.) ll threaded products are merican Standard thread, free fit class 2. GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by goldcolored zinc dichromate to give excellent corrosion resistance and a superior paint base. See pages D- D-4 for a complete description of the GoldGalv hardware finish. NOTE: Standard Spring and Springless Nuts are supplied with a silver electro-galvanized (EG) finish. These items are not visible in a gold system and are universal with other systems finishes and colorations. D-0

11 Threaded Products & Hardware Nuts & Bolts -00 Regular Spring Nut Sizes: 4", 5 6", 8", 2", 5 8", 4" & 8" Nut is square over 2" size. For all and C series channel and inserts. E-42 Hex Head Cap Screw Sizes: 4" x ", 4" x 2", 8" x ", 8" x 2", 2" x 5 6" & 2" x 2" See price sheet for additional sizes. E-50-S Lag Bolt Screw Size: 8" & 2" Drill Size: 4" & 2" B-00 Springless Nut Sizes: 4", 5 6", 8", 2", 5 8" & 4" Nut is square over 2" size. For use with all channels. Silver Electroplated Finish. C-00 Springless Nut Sizes: 4", 8", 2", 5 8" & 4" Nut is square over 2" size. For all, C, E and H series channel and inserts. B-00 Short Spring Nut Sizes: 4", 5 6", 8" & 2" Nut is square over 2" size. For all B series channel and inserts. CM-00 Nylon Cone Nut Sizes: 4", 8", * 2" & **00B 2" For all 5 8" channel. *Will not fit B series channel. **For B Series channel. GoldGalv Finish. E-45 Standard Hex Nut Sizes: 4", 8", 2", 5 8", 4", 8" & " GoldGalv Finish. E-46 Standard Square Nut Sizes: 4", 5 6", 8", 2" & 5 8" GoldGalv Finish. E-4 Flat Steel Washer Sizes: 4", 5 6", 8", 2", 5 8", 4" & 8" GoldGalv Finish. E-48 Lock Washer Sizes: 4", 8", 2" & 5 8" GoldGalv Finish. E-49 Slotted Hex Indented Head Machine Screw Sizes: 4" x 4", 4" x ", 5 6" x 4" & 8" x 4" E-5-D Wood Screw Drive Size : 4" Size B: 2" Max. Rec. Load: 00 lbs. ES-42 Seismic Stiffner Nut Size: ES-42-2 x 2" Bolt Dia.: 2" ES-45 Swivel Nut and Jam Nut Combinations Sizes: 8" & 2" GoldGalv Finish. H-00 Long Spring Nut Sizes: 8", 2" & 5 8" Nut is square over 2" size. For all E and H series channel and inserts. UC-00 Universal Nylon Cone Nut Sizes: 4", 8" & 2" For all 5 8" & 2" channels. May be used with LL strut depths. Can be used for CM-00, -00, B-00 & B-00 Series. GoldGalv Finish. B D-

12 Threaded Products & Hardware Nuts & Bolts (continued) EF-4 - to -80 Swivel Eye B E-20 Fender Washer SIZE DI. HOLE STD. CT. NO. (IN.) (IN.) STD. (IN.) CTN. EF4 / EF-4-/ EF-4-/ Springless Stud Nut BOLT LENGTH STD. CT. NO. DI. (IN.) (IN.) CTN. / /4 X -/ /8 X /8 X -/ /2 X * /2 X -/4* * Cannot be used with B Series channel. B DESIGN STD. CT. NO. (IN.) (IN.) LOD LBS. CTN. E20 /8 8 E20 /2 2 8, , to -85 Swivel Joint E-22 B Regular Spring Stud Nut BOLT LENGTH STD. CT. NO. DI. (IN.) (IN.) CTN. 82 / /4 X -/ /8 X /8 X -/ /2 X /2 X -/ For all and C series channels. B DESIGN STD. CT. NO. (IN.) (IN.) LOD LBS. CTN. E22 /8 8 E-22-/2 2 8, ,800 0 Swivel Eye with Stud Swivel Joint with Stud E-0 B B DESIGN STD. CT. NO. (IN.) (IN.) LOD LBS. CTN. E0 /8 8 E-0-/2 2 8, , B E- B DESIGN STD. CT. NO. (IN.) (IN.) LOD LBS. CTN. E /8 8 E--/2 2 8, ,800 0 D-2

13 Threaded Products & Hardware Threaded Rod E-5 Coach Screw Rod H-04 Hanger Rod: Continuous Thread E-5 Black available upon request Machine-threaded opposite end, carbon steel Order by Cat. No., rod size and rod length ROD STNDRD STD. CT. NO. SIZE (IN.) ROD LENGTHS CTN. E-5-/8 8 4, 6, 8, 0, 2 00 E-5-/2 2 4, 6, 8, 0 00 R-Series Continuous Thread Rod Galvanized DT FOR PRESSURE PIPING ROD ULTIMTE ROOT RE NOMINL MX. SFE STD. CT. NO. SIZE LOD IN LBS. THRED PIPE SIZE LOD T 450 CTN. R628-6 FT R68-6 FT. 8 6, " 2" R648-6 FT. 2, " 2",0 60 R028-0 FT R08-0 FT. 8 6, " 2" R048-0 FT. 2, " 2",0 00 Load Ratings based on safely factor of three. Beam Clamps for Mounting Pipe and Conduit U-5, U-52 H-04 Series Rod SIZE THREDS DESIGN STD. CT. NO. (IN.) PER INCH LOD LBS. CTN. H-04-/ * H-04-/ * H-04-/2 2,0 * H-04-5/8 5 8,80 * H-04-/ ,0 * H-04-/8 8 9,0 * H ,960 * Black available upon request. *Standard lengths 6 ft., 0 ft. and 2 ft. Standard Rod Coupling ROD STD. CT. NO. SIZE (IN.) (IN.) CTN. H-9-/ H-9-5/ H-9-/ H-9-/ H-9-5/ H-9-/ H-9-/ H Standard Finish GoldGalv, unless otherwise stated. U-5, U-52 Conduit Clamp ROD STD. CT. NO. SIZE (IN.) (IN.) CTN. H-9-/4X/ H-9-/8X/ H-9-/2X5/ H-9-5/8X/ H-9-/4X/ CONDUIT MX. FLNGE DIM. STD. CT. NO. SIZE (IN.) THICKNESS (IN.) (IN.) CTN. U U U U U U U Standard Finish GoldGalv brand. For attaching 2" thru 2" conduit to beam, channel, angle or column. Secures conduit to the support parallel or at right angles to it. 5 6" set screw, 2 ga. material. Reducing Rod Coupling D-

14 Fittings & Brackets Fittings & Brackets Series " 5 8" Material Superstrut fittings and brackets are manufactured from hot rolled carbon steel. Dimensions The following standard dimensions apply to all fittings except as indicated on the individual drawings. Hole spacing: 6" from end of fittings Hole spacing: 8" centers Hole size: 9 6" diameter Material: 5 8" wide Material: 4" thickness pplication Instructions Parts drawings illustrate a typical use for the fitting, and in many cases other uses for the part are appropriate. 8" 2" 4 8" Design Data Ratings vary when used with 2 or 4 gauge channel and are shown for each channel material. GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by gold-colored zinc dichromate to give excellent corrosion resistance and a superior paint base. See page D- for complete description of the GoldGalv hardware finish. GoldGalv hardware will be furnished if no other finish is specified. Nuts and Bolts Required Unless otherwise noted, nuts and bolts for use with fittings and brackets should be ordered separately. The standard bolt for the 9 6" hole is a 2" hex head cap screw 5 6" long. The 5 6" length may be used with all series channel. 2 4" 2" 4 8" 6" 6" 8" 2" B20 B202 B20 B204 B205 2" 5 8" 4 8" 6" 4 8" 6" 2" 2" 4 8" 2" 2" B206 B20 B2 B24 B26 2" 2" 2" 5 8" 5 8" " Standard Dimensions Hole Spacing: 6" From End Material: 5 8" Width Hole Spacing: 8" Centers Material: 4" Thick Hole Size : 9 6" Diameter B29 B220 B240 D-4

15 Fittings & Brackets 8" 5 8" 6" 4 8" 4 8" 6" B-242 For use with either 8" or 2" hanger rod B252 STD. CT. NO. (IN.) CTN. B B B B " B25 2" B254 L B254 R 2" 8" " 4" 2" B " B26 6" N205 2" 5 8" 5 8" B25 2" 5 8" B " N-29 2" 2" 5 8" 2" 2" B24 2 4" 8" B260 L 4 8" 2 2" 2 2" X20 2" 5 8" B284 L 8" 2" 5 8" 2" 4 8" 8" 4" 8" 4" 6 8" B260 R 4 8" 5 8" 2" B284 R 2" 2" X204 Slot size is 9 6" x 2" 5 8" 5 8" B26 2" 2" B299 4" X20 9 8" 8" 4 8" 2" 2 5 8" 5 6" 5 8" 2" Standard Dimensions Hole Spacing: 6" From End Material: 5 8" Width Hole Spacing: 8" Centers Material: 4" Thick Hole Size : 9 6" Diameter X208 X289 X299 D-5

16 Fittings & Brackets Z Shape Fittings 2 8" 6" 209 For attaching series channel. 8" CZ209 For attaching back to back. 5 8" 6" 4" Wing Shape Fittings 8" 4" 8" 5 8" 2 8" 6" B209 For attaching B series channel. 8" 2 6" EZ209 For attaching E series channel. 8" 2 8" 8" 6" C209 For attaching C series channel Standard Dimensions Hole Spacing: 6" From End Hole Spacing: 8" Centers Hole Size: " Diameter Material: 5 8" Width Material: 4" Thick 2" 4" 8" 5 8" 2 2" 5 8" 2 2" 2 28 W204 W205 L 9 5 2" 8" 5 2" 8" 8" 8" 8" 2" 4" 5 8" 2 2" 5 8" 2 2" W205-R W24 W29 W220 8" 5 6" 2" 8" 5 2" 8" 4" 9 5 2" Standard Dimensions Hole Spacing: 6" From End Hole Spacing: 8" Centers Hole Size: " Diameter Material: 5 8" Width Material: 4" Thick 5 8" 2 2" 5 8" 2 2" 5 8" 2 2" W224 W226 W228 D-6

17 Fittings & Brackets U Shape Fittings 4" 5c" 5 8" 4" 5 8" 2 2" 6" 5 8" 2 2" e" 5 8" 208 Does not include strut nut or bolts. For series channel. 20 For attaching " series channel 2 For attaching " series channel. B20 9 2" 2" 4 2" 8" B " 8" 6" 2 2" 4"-6 UNF Thread 8" ngular Fittings " 2" " 8" 5 8" 2 2" C20 For attaching C" series channel " 5 8" N2 " 6" 5 8" 5 8" 5 8" " 9 2" " 5 8" E20 For attaching E" series channel. B 2 2" 5 8" " 2 2" 2 2" 2" B ga. 4" Standard Dimensions Hole Spacing: 6" From End Hole Spacing: 8" Centers Hole Size: 9 6" Diameter Material: 5 8" Width Material: 4" Thick Standard Finish GoldGalv, unless otherwise stated. B STD. CT. NO. (IN.) (IN.) CTN. B B B B225 B22 B-29 D-

18 Fittings & Brackets Post Bases 4 Holes 4" Dia. 4 2" 6" 2 Holes 4" Dia. 6 2" 8" 5 8" P-2 5 8" 4 Holes 4" Dia. P-2FL 5 8" 5 8" 6" 6" " 4 2" 6" 5 8" 6" 4 Holes 4" Dia. 2 Holes 4" Dia. 6 2" 8" 5 8" 5 8" P-22 P-22FL 4 Holes 4" Dia. 6" 2" " 6" 2" 5 8" 2 Holes 4" Dia. 4 Holes 4" Dia. 6" 4 2" 5 8" 6 2" 8" 8" 5 8" 8" 4 2" 6" P-24 8" 5 8" 8" P-24FL 5 8" 6" 2 Holes 4" Dia. 8" 6 2" 8" 5 8" 6" 4" P-25 P-25FL 8" 8" 2" 2" 4 Holes 4" Dia. 5 8" 5 8" 5 8" 4" Dia. 6" 4 2" 4 2" 6" 4 2" 6" 4 2" 6" 5 8" 5 6" 8" P-2SQ P-24SQ W " 4 Holes 4" Dia. 4 Holes 4" Dia. 4 Holes 6" Dia. 2" 6" 2" 5 6" 2" 6" 6" 6" 6" 5" 5 8" 4 4" 4 4" 4 4" 4 4" P-206 P-22SQ P-25SQ D-8

19 Fittings & Brackets Special pplication Fittings 4" 2 8" 5 8" 2 6" 5 8" Q255 For 2" standard pipe. Load,500 lbs. Q " 5 8" Q256 For 2" standard pipe. Load,500 lbs. 2" 2 6" 5 8" 4" Q205 6" 6" Q25 2 4" 2 4" 6" Q254 For 4" standard pipe. Load,500 lbs. 6" Standard Dimensions Hole Spacing: 6" From End Material: 5 8" Width Hole Spacing: 8" Centers Material: 4" Thick 9 6" Dia. Hole Size: 9 6" Diameter 4" 9 6" Dia. TR292 Frictionless needle bearings. Design load: 500 lbs. Safety factor of 5. TR294 Frictionless needle bearings. Design load:,000 lbs. Safety factor of 5. D-9

20 Fittings & Brackets Special pplication Fittings (continued) 6" " C N-20 B 2" S-20-L and R R as shown L opposite hand. 2 ga. steel. Design Uniform Load/lbs. -, , C 9 2" Dia. 4" 2" 6" B 6" Dia. Hole 9 6" 6" 4" 2 Holes 2 8" 6" 2 Holes 8 2" 6 8" S204 Design Uniform Load/lbs. -, , " 2 2" 8" 4" S2 Design Uniform Load/lbs. -, , " 5 8" 6" 5 8" 4" 4" 6" 4 8" S205 Design Uniform Load/lbs. -, , Hole 9 6" 0 2" 2 8" 4" 4 2" 4" 8" 5 4" S28 Design Uniform Load/lbs. -, , " 5 8" 5 8" " TS-22 Track Support Requires 8" x 2 2" bolt and nut (not included). Design load:,000 lbs. 6" 2" " TS2 Track Support For uses over channel splice. Requires 8" x 2 2" bolt and nut (not included). Design load: 2,000 lbs Standard Dimensions Hole Spacing: 6" From End Material: 5 8" Width Hole Spacing: 8" Centers Material: 4" Thick Hole Size: 9 6" Diameter B C STD. CT. NO. (IN.) (IN.) (IN.) CTN. S20-L6 or R S20-L8 or R S20L 0 or R S20-L2 or R S20-L4 or R S20-L6 or R S20-L8 or R S20-L20 or R B STD. CT. NO. (IN.) (IN.) CTN. N N N N N D-20

21 Fittings & Brackets Brackets 5 4" 8" 6 2" 6" 5 4" 8" 8 2" 6" 4" 8" 20 2" 4" 6" 6" 6" 6" 6" 6" S222 Design Uniform Load/lbs. -,200,000 -, " " 5 8" 5 8" S226 Design Uniform Load/lbs. -,200,000 -, " S248 Design Moment (channel upright as shown) When supported by -,200 0,800 inch lbs. -,400,550 inch lbs. pplies to fitting only, not to the arm. For -,200 -, " 5 8" S24 Design Moment (channel upright as shown) When supported by -,200 5,250 inch lbs. -,400,650 inch lbs. pplies to fitting only, not to the arm. For -,200 B-,202 -,400 B-, " 6 4" S26 Design Uniform Load/lbs. -, , " 5 8" S-250 May be installed inverted with no change in load ratings. Strut section made from half slot channel. Sizes: 6", 2", 8" & 24" S-25 Strut section made from half slot channel. Sizes: 2", 8", 24", 0" & 6" S-256 When installed in inverted position reduce load rating 40%. Strut section made from half slot channel. Sizes: 6", 2", 8" & 24" DESIGN STD. CT. NO. (IN.) LOD LBS. CTN. S ,500 S S S Standard Finish GoldGalv, unless otherwise stated. DESIGN STD. CT. NO. (IN.) LOD LBS. CTN. S ,650 S ,050 S S S DESIGN STD. CT. NO. (IN.) LOD LBS. CTN. S ,000 S S S D-2

22 Concrete Inserts Concrete Inserts (Series 00/400) B804 C-804 4" 4" B-02 C-02 Standard lengths 0 ft. and 20 ft. length tolerance 6". ssemblies available in any length from 2" to 20 ft. Consult factory. Insert with end caps and foam filler strip installed. Material: B-02 and C-02 Insert Channel-2 ga. steel. B-804 and C-804 End Caps 2 ga. steel. Superstrut continuous insert channel is cold formed from 2 gauge hot-rolled strip steel in two basic sizes as follows: CT. NO. B " x 6" dim. 8" slot CT. NO. C " x 8" dim. 8" slot Finishes Product is available in GoldGalv pre-galvanized (PG), hot-dipped galvanized (HDG) and stainless steel (SS). Contact your T&B Sales team for delivery and pricing. Standard lengths are 0 ft. and 20 ft. Product is supplied with foam filler and end caps to prevent seepage of concrete into channel. pplication For casting into concrete walls, floors or ceilings to provide attachment anywhere along the continuous slot. Design Data Load ratings as shown have a safety factor of in,000 lb. hard rock concrete. Where good concrete does not exist, the load ratings shall not apply. GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by gold-colored zinc dichromate to give excellent corrosion resistance and a superior paint base. See page D- for a complete description of the GoldGalv hardware finish. GoldGalv hardware will be furnished if no other finish is specified. Design Load lbs. 8" 5 6" 6" 8" 2 2" 6" 2,000 lbs. per foot in,000 lbs. hard rock concrete with a safety factor of 2. NOTE: B-02 and C-02 are furnished with:. Concrete safe tape applied to interior of channel to cover holes. B. Styrene insert between tape and 8" continuous opening. C. Two end caps on either side of strut to prevent concrete seepage. 6" 5 8" 5 8" 8" B-02 C-02 CT. NO. DESCRIPTION B-02* Insert channel 2 ga. steel 6" depth C-02* Insert channel 2 ga. steel 8" depth B804 End cap in B Series Concrete Insert C-804 End cap in C Series Concrete Insert *dd suffix -0 for 0' lengths and -20 for 20' lengths D-22

23 Concrete Inserts 450 End Cap FOR X STD. CT. NO. CHNNEL (IN.) MTERIL CTN. C-450TB C-,200 2 ga. 00 Does not come in pairs, order number of total pieces required. Inserts may be assembled from short pieces of channel by use of end caps. Order closure strip separately. x TB Spot Insert Top is Deep Drawn Cup n insert with a knockout saves covering the opening. ccommodates hanger rod sizes from 4" through 8" by means of an B-02 insert nut Design load:,50 lbs. in,000 lb. hard rock concrete with a safety factor of Order B-02 nut separately B-02 Unhardened Square Nut STD. CT. NO. SIZE (IN.) CTN. B02 / B-02-/ B-02-/ B-02-5/ B-002-/ B-02-/ For use with Spot Insert Cat. No C45 Metal Deck Ceiling Bolt Metal Deck Ceiling Bolts are used with our Figure 2. Rod Couplings ordered separately. Made special to customer order. Material: Steel Knockout 4" 5 8" 2" 2" 8" 9 2" 2 ga. Steel 452TB B-02 Finish: Standard Finish GoldGalv Black (add suffix -B ) Electro-Galvanized (add suffix -EG ) 6" Ordering: Specify size, dimension, catalog number and finish. C WT. B C MX. LOD CT. NO. ECH (IN.) (IN.) (IN.) (LBS.) C45 /8.5 S 8 60 C45 /2.9 p 2 4,0 e C45 5/ ,80 c C45 / i 2,0 C45 / f 8 2,0 C45 6 y 2 4 4,960 B C45 D-2

24 Beam Clamps Superstrut Beam Clamps Materials Most products are manufactured from hot-rolled carbon steel bars or hot-rolled strip steel. Pipe rollers are cast iron. Products which are copper placed carry the letter T in the prefix. Design Loads Where design loads are indicated, they provide for a safety factor of in conformance with the MERICN STNDRD CODE FOR PRESSURE PIPING. GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by gold-colored zinc dichromate to give excellent corrosion resistance and a superior paint base. See pages D- D-4 for a complete description of the GoldGalv hardware finish. GoldGalv hardware will be furnished if no other finish is specified. Beam Clamps for Mounting Channel 6" 2 8" " U50, U502 Furnished complete. Design load U50 2,50 lbs. U502 -,000 lbs. STD. CT. NO. FOR CHNNEL (IN.) CTN. U B-200 B-400 C-200 B-402 U C-202 H-200 8" 8" U504 U505 " 2 4" 8" " U50 2" x 2" set screw included. Order separately one 2" x 2" hex head cap screw and 2" channel nut. Channel -,200 -,400 Design Load lbs., U Order separately one 2" x 2" hex head cap screw and 2" channel nut. Channel -,200 -,400 Design Load lbs., D-24

25 Beam Clamps Beam Clamps for Mounting Channel (continued) 4" 4" 8" " 8" Hole 9 6" Dia. 8" U54 8" x 2" set screw included. Design load 50 lbs./per pair. 4" 2 8" U55B For all "B" series channel. 2" x 2" set screw included. Design load 800 lbs. 4" 5 8" U54 8" x 2" set screw included. Design load,650 lbs./per pair. FLNGE DESIGN STD. CT. NO. WIDTH* (IN.) (IN.) LOD LBS. CTN. U ,000 0 U ,00 0 U *When ordering specify flange width. U Channel Wide Flange Beam 4" 2" U55 For all series channel. 2" x 2" set screw included. Design load 800 lbs. 2" -59 Standard Finish GoldGalv brand. Channel Series Design load 800 lbs./ea. 5 8" 25 2 U520, U-52 & U-522 Standard Finish GoldGalv brand. Nuts, cap screws and set screws included. D-25

26 Beam Clamps Beam Clamps for Hanging Rod Beam Clamps Malleable Iron, Silver Electroplated Finish 4" 2 5 8" 500SS6, 502SS6 and 50SS6 in 6 Stainless Steel, also available. BSE SIZE JW TPPING SET SCREW (IN.) OPENING OF BSE ND LOD TORQUE IN STD. CT. NO. B (IN.) BCK HOLES RTING INCH-LBS. CTN. 500-SC SC , , , SC Safety Factor of. Loan Ratings based on bottom hole of Beam Clamp. CS File No. LR " C B C D STD. CT. NO. (IN.) (IN.) (IN.) (IN.) CTN. B 8" 2 8" U562 Beam Clamp 2" set screw included. Rod Size: 2" Design load 500 lbs. US562 Beam Clamp with Swing Hanger 2" screw included. Rod sizes: 2". Design load 800 lbs. 4" Square nut, order separately. U562 Beam Clamp Optional Use 2" set screw included. Rod sizes: 2" Design load 800 lbs. For 20 swivel application use ES-45-2 nut. " 8" 2 4" U56 Beam Clamp 8" set screw included. Rod sizes: 8" Design load 250 lbs. B 540 Side Beam Hanger Clip Finishes GoldGalv brand or Black (B) D 540 / /2 EC / / Square nut, order separately 9 6" Dia. 6" Dia. 4" Dia. 2 6" U56 Beam Clamp optional Use 8" set screw included. Rod sizes: 8" Design load 400 lbs. US56 Beam Clamp with Swing Hanger. 8" set screw included. Rod sizes: 8". Design load 540 lbs. 6" 2" 2 6" 542 Side Beam Hanger Clip Finishes GoldGalv brand or Black (B) Rod Size 8" 2" Design Load lbs. 60,000 Standard Finish GoldGalv, EG, HD, & SS available. U-568 Beam Clamp Safety Strap Standard Finish GoldGalv brand For U-56 beam clamp. U-568 Beam Clamp Safety Strap Standard Finish GoldGalv brand For U-562 beam clamp. D-26

27 Beam Clamps Beam Clamps for Hanging Rod (continued) Coach Screw U-560 Heavy-Duty Beam Clamp DIMENSIONS (IN.) DESIGN STD. CT. NO. B C LOD LBS. CTN. U560 /4 4 U-560-/8 8 U-560-/2 2 U-560-5/8 5 8 S-54 Swing Connector Standard Finish GoldGalv brand Rod Sizes: 8" For use with wood beam. 8" x 4" bolt, nut and clevis included. Channel ngle Connector. Standard Finish GoldGalv. vailable in Electro-Galvanized (EG) finish. Integral pilot, prevents twist x 2, x 2, x 2 2, x 2 2, U5 Clevis & Swing Connector Rod Size 2" Standard Finish GoldGalv brand For use with wood beam. B "C" Set Screw Included 8" Tapped Hole Size U-564 Heavy-Duty Beam Clamp "C" Set Screw Included DIMENSIONS (IN.) DESIGN STD. CT. NO. B C LOD LBS. CTN. U-564-/8 8 U-564-/2 2 U564 5/ x 2 4, x 2 4, x 2 4, " B vailable in Electro-Galvanized (EG) finish. Tapped Hole Size D-2

28 Beam Clamps B Beam Clamps for Hanging Rod C E-2 Structural Steel Clamp DIMENSIONS (IN.) WT. CT. NO. B C LBS./C 8" or 2" Rod *E **E ssembly requires two H-6-C ( 8") or two H-6-D ( 2") square nuts to attach hanger rod. 2" steel. * Load rating of 500 lbs. with a safety factor of three. ** Load rating of 800 lbs. with a safety factor of three. Galv-Krom finish. E-22 Clamp with Swing Connector E-2 nchor Clip Clamps to I-beams, channels, angles and column Two sizes are available, one for 8 inch and the other for 2 inch hanger rod. Each takes flanges up to.8 inch thickness For use with E-2 and E-22 clamps when hanger rod is not in straight through position. ROD MX. BEM FOR USE WT. CT. NO. SIZE (IN.) WIDTH "" (IN.) WITH LBS./C E E-2-8 or 20 E E-22-8 E E-2-2 or 26 E E-22-2 nchor Clips should be used when clamps are subject to excessive vibration. To obtain the correct size clips, add inch to the flange width. If length required is not standard, order next largest standard length. Galv-Krom finish. B C E-2 clamp with swing connector ffords a convenient method of attaching to angled beams DIMETER DIMENSIONS (IN.) WT. CT. NO. FOR ROD (IN.) B C LBS./C 8" or 2" Rod *E **E * Load rating of 400 lbs. with a safety factor of three. ** Load rating of 550 lbs. with a safety factor of three. Galv-Krom finish D-28

29 Beam Clamps Beam Clamps for Hanging Rod (continued) E-60 djustable Beam Clamp Clamps to I-beam where edge of beam flange does not exceed.8 inch thickness Hook rod is furnished in three lengths to fit beam flanges up to 6, 9 or 2 inch widths CT. NO. BEM FLNGE WT. 2" HNGER RODS WIDTH (IN.) LBS./C 2" Rod 2 8, or 4 E to 6 5 E to 9 25 E to 2 54 Load rating 800 lbs. with a safety factor of three. ssembly requires hanger rod of the proper length and size plus two H-4-D nuts 6" steel and 2" hook rod. Galv-Krom finish. U-568 Beam Clamps BEM FLNGE STD. CT. NO. WIDTH (IN.) (IN.) CTN. U U U U U U U U ga. material. U569 Beam Clamp Standard finish GoldGalv Maximum flange width 5" Design load 400 lbs. 8" 2 8 U-568 Beam Clamp Safety Strap Standard Finish - GoldGalv brand. For U-560 and U-564 beam clamp. U50 Beam Clamp with Safety Rod Standard finish GoldGalv Flange width 4" min. 8" max. 6 x 2 Min. 5 8 Max. Sizes: 2" For use with 8" rod, see U569 Design load 650 F 500 lbs. 8" C-5L Clamp with Lock Nut D C-5L C B ROD DIMENSIONS (IN.) DESIGN STD. CT. NO. SIZE (IN.) B C D LOD LBS. CTN. C5L /8 8 C-5L-/2 2 C-5L-5/8 5 8 C-5L-/4 4 C-5L-/ , Standard Finishes - GoldGalv brand, Black (B), Stainless Steel (SS) and Electro-Galvanized (EG). Carbon Steel. D-29

30 Beam Clamps Beam Clamps for Hanging Rod C- Steel Top Beam Clamp & C-8 Steel Wide JawTop Beam Clamp C-, C-88 ROD DESIGN SIZE PIPE DIMENSIONS (IN.) LOD STD. CT. NO. (IN.) SIZE B C D E F LBS. CTN. C / C--/ ,40 50 C-8-/ C-8-/ ,40 50 Standard Finish GoldGalv,, Black (B) and Electro-Galvanized (EG). M-5L Clamp with Lock Nut E C D B M- Steel Top Beam Clamp Junior Top Beam C-Clamp Standard finish is Gold-Galv vailable in Electro-Galvanized (EG) or Black (B) Malleable Iron Provides clamping under roof installations with bar joist construction. Max. joist thickness 5 8" Order by Cat. No., rod size M- 4" ROD SIZE (IN.) M-8 Steel Wide Jaw Top Clamp Top Beam C-Clamp Rod Size: 8", 2", 5 8" and 4" DESIGN LOD LBS ,000 vailable in Electro-Galvanized (EG) or Black (B) Malleable Iron Provides clamping under roof installations with bar joist type construction Order by Cat. No. and rod size B C M-8 4" ROD SIZE (IN.) DESIGN LOD LBS. M-5L ROD SIZE B C DESIGN STD. CT. NO. (IN.) (IN.) (IN.) LOD LBS. CTN. M-5L-/ M-5L-/ M-5L-5/ M-5L-/ vailable in Electro-Galvanized (EG) or Black (B). D-0

31 Beam Clamps for Mounting Pipe and Conduit Beam Clamps C-24, C-248 & C-249 Steel Conduit Clamps Pipe Supports Three types of pipe clamps are available to provide right angle, vertical and parallel attachment to a beam. Types RC, EC and PC are malleable iron clamps with an edge that grips the structural member for maximum holding power when tightened. Type RCS clamps are all steel, providing two bearing surfaces for strong attachment for mounting pipe or conduit at right angles to the beam. ll parts are electrogalvanized, including the threads. The clamps are designed for clamping to a wide variety of beam thicknesses and tapers. Can be installed using only a wrench. versatile clamp for attaching conduit to any type of beam, channel, angle or column Designed to hold the conduit snug against the support with conduit either parallel or at right angle to it The case-hardened set screw bites into the structural member for maximum security 8" steel CONDUIT MX. BEM FLNGE THICKNESS SIZE C-24 C-248 C C B Dim Dim. B Dim. C Dim. D Per Carton Wt. in lbs./c 6 59 Galv-Krom finish. 8 D 5 8 RC Clamp Malleable Iron RCS Clamp Steel For mounting pipe or conduit at right angles to the beam Use SS6 suffix for 6 Stainless Steel Use HDG suffix for hot-dip galvanized DIMENSIONS (IN.) O.D. OF NOM. CT. NO. CONDUIT CONDUIT OR STD. & SIZE OR PIPE PIPE SIZE CTN. RCS-/ RCS-/ RCS RCS--/ RCS--/ RCS RC-/ RC-/ RC-/ RC RC--/ RC--/ RC-2-SC RC-2-/ RC RC--/ RC-4-SC EC Clamp Malleable Iron For mounting pipe or conduit vertically across the beam Use SS6 suffix for 6 Stainless Steel Use HDG suffix for hot-dip galvanized PC Clamp Malleable Iron For mounting pipe or conduit parallel to the beam Use SS6 suffix for 6 Stainless Steel Use HDG suffix for hot-dip galvanized DIMENSIONS (IN.) O.D. OF NOM. CT. NO. CONDUIT CONDUIT OR STD. & SIZE OR PIPE PIPE SIZE CTN. EC / EC-/ EC EC--/ EC--/ EC EC-2-/ EC PC-/ PC / PC-/ PC PC--/ PC--/ PC PC-2-/ PC PC--/ PC D-

32 Beam Clamps Conduit and Pipe Hangers 6H Series Without bolt Fig. 6H- T Threaded Series Threaded without bolt Fig. 6H-B Series With bolt and hex nut Fig. 2 6H- TB Threaded Series Threaded with bolt Fig. 4 6H Series Conduit and Pipe Hanger ccommodates 2" through 4" EMT or rigid conduit Can be used for either vertical or horizontal installation 6HTB Series have a built-in nut so there are less parts to handle or drop Installs easily with a screwdriver WITHOUT BOLT WITH BOLT CT. FIG. CT. FIG. EMT RIGID CONDUIT STD. NO. NO. NO. NO. (IN.) OR PIPE (IN.) CTN. 6H0 6H0 B H0 T 6H0 TB H 6H-B H-T 6H-TB H2 6H2-B H2-TB H2 /2 6H2 /2-B H2 /2-TB H-SC 6H-B H-TB H4 6H4-B H4-TB H5 6H5-B H5-TB H6 6H6-B H 6H-B H8 6H8-B H9 6H9-B Standard Finish Electro-Galvanized (EG). Use SS suffix for Stainless Steel. Loading rating 500 lbs. with a safety factor of. D-2

33 Pipe Straps, Conduit Clamps & Hangers Excellent Corrosion Resistance and a Superior Paint Base GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by gold-colorized zinc dichromate to give excellent corrosion resistance and a superior paint base. See page D- for a complete description of the GoldGalv hardware finish. GoldGalv hardware will be furnished if no other finish is specified. Materials Most products are manufactured from hot-rolled carbon steel bars or hot-rolled strip steel. Pipe rollers are cast iron. Products which are copper plated carry the letter T in the prefix. Design Loads Where design loads are indicated, they provide for a safety factor of in conformance with the MERICN STNDRD CODE FOR PRESSURE PIPING. Hanger Design Pipe hangers are of advanced design and afford a new and better way of ordinary use. Standard Dimensions The following, except where noted, apply to all beam clamp fittings. Hole Size: 9 6" diameter Material: 5 8" wide Material: 4" thick GoldGalv Outperforms Copper Plated In a test conforming to STM G-8-84, also known as the Kesternich Test, Superstrut s GoldGalv electrogalvanized zinc dichromate finish achieved superior corrosion resistance in comparison to copper plated. Performed and certified by an independent testing laboratory, the stringent Kesternich test is equivalent to an acid rain environment. The test procedure exposes subject material to condensed moisture containing harsh sulfur dioxide (S02) which accelerates the aging process. During the series of test time cycles, the material is thoroughly inspected for signs and progression of damaging red rust. The first test series conducted included various light-duty adjustable clevis hangers assembled to copper tubing. The GoldGalv finish exhibited five times the red rust resistance as compared to copper plated. The second test series was performed on various O.D. pipe straps attached to copper tubing and continuous slot channel. GoldGalv achieved greater red dust resistance by seven times over copper plating. Once tests were completed, all copper tubes were split open and inspected for signs of electrolysis. The copper tubes showed minimal deterioration as a result of the test and no indication of electrolysis occurrence when attached to material with GoldGalv finish. STM G-8-84 Corrosion Test Results INITIL 50% 00% FINISH RED RUST RED RUST RED RUST Test Series I: Light-Duty djustable Clevis Hanger GoldGalv 20 hours 26 hours *Never obtained Copper Plated 24 hours 48 hours 2 hours Test Series II: O.D. Pipe Straps GoldGalv 68 hours 92 hours 240 hours Copper plated 24 hours 48 hours 68 hours *Test series ended after 60 hours. D-

34 Pipe Straps, Conduit Clamps & Hangers Superstrut Pipe Straps Pre-ssembled for Easy Handling and Sorting Superstrut Pipe Straps are designed to be twist inserted anywhere along the slot side of the channel. Pipes can be placed as closely as pipe couplings permit. Some unique features of the straps include: Bolt head is combination slot and hex head for flexibility of attachment Square nut is captivated on the shoulder for easy one-handed tightening Straps are interchangeable with 2" strut for broader application Straps are shipped assembled so counting and sorting are easier Pipe or conduit sizes are sown on the strap for easy identification ll Superstrut Straps are preassembled for easy handling and sorting 00 Superstrut Straps for EMT EMT O.D. STEEL STRP DESIGN LOD STD. CT. NO. SIZE (IN.) SIZE (IN.) THICKNESS (LBS.) CTN. Standard Finishes GoldGalv brand. Consult Factory regarding other Finishes and Materials 00 8-STR ga STR ga STR ga STR.6 4 ga STR ga STR ga STR ga Design Loads 0 Superstrut Straps for O.D. Tubing TUBING STEEL STRP DESIGN LOD STD. CT. NO. O.D. (IN.) THICKNESS (LBS.) CTN ga ga /2-STR 2 4 ga / ga /4 4 4 ga /8 8 4 ga STR 4 ga /8 8 4 ga., /4 4 4 ga., /8 8 4 ga., /2 2 4 ga., / ga., /4 4 2 ga., /8 8 2 ga., ga., / ga., / ga., / ga., / ga., ga.,00 50 D-4

35 Pipe Straps, Conduit Clamps & Hangers Superstrut Pipe Straps (continued) 0 Superstrut Straps for O.D. Tubing (continued) 02 Superstrut Straps for Rigid Conduit, IMC and Pipe For Rigid or IMC Conduit, Pipe and Electric Metal Tubing (EMT) TUBING STEEL STRP DESIGN LOD STD. CT. NO. O.D. (IN.) THICKNESS (LBS.) CTN 0-2-/ ga., / ga., ga., ga., ga., /8 8 2 ga., /2 2 2 ga., /8 5 8 ga., /4 4 ga., /8 8 ga., ga., /8 4 8 ga., /4 4 4 ga., /8 4 8 ga., /2 4 2 ga., / ga., /4 4 4 ga., /8 4 8 ga., ga., /8 5 8 ga., /4 5 4 ga., /8 5 8 ga., /2 5 2 ga., / ga., / ga., / ga., ga., / ga., / ga., / ga., / ga., / ga., / ga., / ga., ga.,650 0 RIGID CONDUIT OR O.D. STEEL STRP DESIGN LOD STD. CT. NO. PIPE SIZE (IN.) SIZE (IN.) THICKNESS (LBS.) CTN. Standard Finishes GoldGalv brand, Electro-Galvanized EG (Silver) ga ga ga ga ga ga STR ga ga., ga., ga., ga., ga., ga., ga., ga., ga., ga., Universal Clamp PIPE STEEL STRP DESIGN LOD STD. CT. NO. O.D. (IN.) THICNESS (LBS.) CTN. Standard Finishes GoldGalv brand, Electro-Galvanized (Silver) use EG suffix, (i.e.) 0--/2EG 0-/ ga / ga ga / ga / ga ga Standard Finishes GoldGalv brand, Electro-Galvanized (i.e.) 0--/2EG (Silver) Copper Plated CT0--/2. Consult factory regarding other finishes and materials. D-5

36 Pipe Straps, Conduit Clamps & Hangers Cobra One-Piece Cable and Pipe Clamp Takes a bite out of your installation time! One-piece, heavy-duty construction ready to install right out of the box, no need to break apart and re-assemble, no screws or bolts to drop Installs quickly and securely using one hand Universal bolt head accepts a range of tools Eliminates the guesswork from clamp selection one catalog number attaches equal trade sizes of EMT and rigid conduit Parallel hook design keeps conduits and cable square with strut Reconfigure wiring without complete disassembly. Remove cables easily without disturbing neighboring clamps Simple Product Selection, Solid Installation Clear markings on each clamp identify the catalog number, min./max. outer cable diameters, EMT/Rigid trade sizes, CS and UL stamps Works with all depths of strut 6" to 4" One-size clamp works on equal trade sizes for both EMT and rigid conduit Two hooks on the same side make the clamp easy to install and keep conduits and cable square with strut Rugged stirrup and wide saddle design holds securely with no damage to conduit or cable Suggested design load is 200 lbs. ( 2" to 2"); 50 lbs. (2 2" to 4"). Safety factor 4: (safety factor = ratio of ultimate load to the design load) Heavy-duty 5 6" hex bolt with multi-driver head (Robertson square, Phillips cross-recess and slot) provides full range of installation options. Virtually any tool will work! Bright zinc finish clamps are electrogalvanized after fabrication for additional durability ccepts Multi-driver combination bolt head accepts a wrench, screwdriver or nut driver. ttaches ttaches a full range of EMT, rigid conduit and cable to strut channels. Remove Remove cable or pipes easily without disturbing neighboring clamps. FOR EMT ND RIGID STTIC LOD CONDUIT CBLE O.D. LIMIT (LB) STD. CT. NO. TRDE SIZE (IN.) RNGE (IN.) SFETY FCTOR = 4 CTN. Electro-Galvanized Steel CPC CPC CPC CPC CPC CPC CPC CPC CPC CPC Stainless Steel; dd suffix SS or SS6. FOR EMT ND RIGID STTIC LOD CONDUIT CBLE O.D. LIMIT (LB) STD. CT. NO. TRDE SIZE (IN.) RNGE (IN.) SFETY FCTOR = 4 CTN. 6 Stainless Steel CPC050SS CPC05SS CPC00SS CPC25SS CPC50SS CPC200SS CPC250SS CPC00SS CPC50SS CPC400SS D-6

37 Pipe Straps, Conduit Clamps & Hangers ngled for Easy Tightening! ngler Pipe and Conduit Clamp Pipe and Conduit Clamp For EMT, IMC, Rigid and Standard Pipe Universal Series STRP DESIGN INSTLL TORQUE STD. CT. NO. SIZE (IN.) THICKNESS LOD (LBS.) (IN. LBS.) CTN. Galv-Krom Finish C 09 /2 2 4 ga C 09 /4 4 4 ga C 09 4 ga C 09 /4 4 4 ga C 09 /2 2 2 ga C ga C 09 2 / ga C 09 2 ga C 09 /2 2 ga., C ga., SilverGalv Finish C 09 /2 EG 2 4 ga C 09 /4 EG 4 4 ga C 09 EG 4 ga C 09 /4 EG 4 4 ga C 09 /2 EG 2 2 ga C 09 2 EG 2 2 ga C 09 2 /2 EG ga C 09 EG 2 ga C 09 /2 EG 2 ga., C 09 4 EG 4 ga., For Rigid Conduit and Standard Pipe Rigid Series STRP DESIGN INSTLL TORQUE STD. CT. NO. SIZE (IN.) THICKNESS LOD (LBS.) (IN. LBS.) CTN. Galv-Krom Finish C 09R /2 2 4 ga C 09R /4 4 4 ga C 09R 4 ga C 09R /4 4 4 ga C 09R /2 2 2 ga C 09R ga C 09 2 / ga C 09 2 ga C 09 /2 2 ga., C ga., SilverGalv Finish C 09R /2 EG 2 4 ga C 09R /4 EG 4 4 ga C 09R EG 4 ga C 09R /4 EG 4 4 ga C 09R /2 EG 2 2 ga C 09R 2 EG 2 2 ga C 09 2 /2 EG ga C 09 EG 2 ga C 09 /2 EG 2 ga., C 09 4 EG 4 ga., Hex head size 8" for 2" to 4" sizes, 2" for 2" to 4" sizes. Material: Stamped Steel. Pipe sizes 2 2" to 4" utilize the same clamps for the Rigid Series and the Universal Series. D-

38 Pipe Straps, Conduit Clamps & Hangers Pipe Straps -6 Snap Guard Cushioned Clamp Tube Series P-6 Pipe Series ssembly consisting of GoldGalv finish steel clamp with bolt/locknut and cushion Secure pipes, tubes and hoses for fluid conductors Installation is easy and requires no more time than a simple pipe clamp installation Cushion absorbs the shocks and associated vibrations from fluid surges in tubes, pipes and hoses It can handle temperatures from -40 F to 00 F Cushioned Clamp assemblies are available individually bagged -6 P-6 U-6, U- Two-Hole Cushioned Clamp U-6 U- Guides, protects and uniformly spaces line runs. Low-cost, time-saving method of attaching tubing and hose to equipment Cushion is built to withstand the effects of most oils, chemical and industrial cleaning compounds, in temperatures from -50 F to 25 F. Interlock edge insures cushion remains in place Clamp available in steel with the GoldGalv hardware finish ttached with two standard fasteners to any flat surface, this clamp eliminates the use of special channels, providing a savings in both space requirements and cost Cushioned clamps reduce vibration, shock and noise in fluid systems and eliminates electrolysis O.D. TUBING SIZES STNDRD PIPE SIZES SSEMBLY TUBE SSEMBLY NOMINL STD. CT. NO. O.D. (IN.) CT. NO. PIPE SIZE (IN.) CTN. Standard Finishes GoldGalv brand. vailable in Stainless Steel use SS suffix. (i.e) -6-SS, Electro-Galvanized (Silver) use EG suffix. (i.e) -6-EG -6-/4 4 P-6-/ /8 8 P-6-/ /2 2 P-6-/ /8 5 8 P-6-/ /4 4 P /8 8 P-6--/ P-6--/ /8 8 P /4 4 P6-2-/ /8 8 P /2 2 P-6--/ /8 5 8 P / / / / / / / COPPER ND COPPER NOMINL SSEMBLY STEEL TUBING WTER PIPE PIPE STD. CT. NO. O.D. (IN.) (NOM.) (IN.) SIZE (IN.) CTN. Standard Finishes GoldGalv Brand U6 / U-6-/ U-6-/ U-6-5/ U-6-/ U-6-/ U-6-25 U-6--/ U-6--/4 4 0 U-6--/ U-6--/2 2 0 U-6--5/ U-6--/4 4 0 U-6--/ U U-6-2-/ U-6-2-/ U--/ U-- 0 U---/4 4 0 D-8

39 Pipe Straps, Conduit Clamps & Hangers Pipe Straps (continued) C-6 Isolator for Copper Tubing Features: Designed for use with Superstrut channel and pipe straps and Superstrut C- Hangers, and may also be used with all standard flatbar or malleable iron hangers. Materials: Manufactured from one-piece steel shell with reinforcing ribs for stiffening and alignment. Padding is of processed non-conducting hairfelt and is cemented to the metal. Design of ribs creates a hinge so isolator may be opened and closed to install. pplication: To provide a means to effectively isolate copper tubing from its supports to prevent the transmission of sound and vibration. S6 Cushioned Strip For Isolation and Vibration pplications For use with 0 O.D. tubing and pipe clamp. To determine 0 clamp size, add 4" to O.D. tube size to allow for the cushioned strip material. 4" markings for fast measuring and cutting. Measurement chart is printed on back of carton. 20 feet included in each carton. Prevent metal-to-metal contact with the cushioned strip material. It aids in sound insulation, shock absorption and protects against corrosion, distortion and abrasion. Cushioned strip material is designed for optimal use between -0 F and 00 F. Cushioned strip material combined with the Superstrut 0 pipe strap can handle clamping assignments from 4" to 6. C-08-U Short Strap for Channel or Wall Mounting B NOMINL HNGER, C- WIDTH SIZE PIPE SIZE OR STD. CT. NO. (IN.) (IN.) PIPE STRP, 02 (IN.) CTN. C6 / C-6-/ C C-6--/ C-6--/ C C-6-2-/ C C-6--/ C Order by Cat. No. and size. S6 Sold in a carton of 20 feet. CUSH--STRIP Order 0 clamp separately. DIMENSIONS (IN.) PIPE HOLE STOCK DESIGN STD. CT. NO. SIZE B SIZE SIZE LOD LBS. CTN. C-08-U-/ x C-08-U-/ x C-08-U x C-08-U--/ x C-08-U--/ x C-08-U x C-08-U-2-/ x 5 8, C-08-U x 5 8, C-08-U--/ x 5 2, C-08-U x 5 2, C-08-U x 5 2,200 0 C-08-U x 5 8,200 0 Carbon Steel. 5 8" D-9

40 Pipe Straps, Conduit Clamps & Hangers Cable Clamps CB8 Counter Bed CH8 CH8 and CX8 Heavy-Duty Cable Clamp FIG. EMT RIGID CBLE STD. CT. NO. NO. SIZE (IN.) SIZE (IN.) O.D. (IN.) DESCRIPTION CTN. CH8-055EG Conduit to strut clamp 00 CH8-08EG Conduit to strut clamp 00 CH8-0EG Conduit to strut clamp 00 CH8-25EG Conduit to strut clamp 00 CH8-5EG Conduit to strut clamp 00 CH8-5PG Conduit to strut clamp 00 CH8-205EG Conduit to strut clamp 00 CH8-250EG Conduit to strut clamp 00 CH8-00EG Conduit to strut clamp 25 CH8-5EG Conduit to strut clamp 25 CH8-425EG Conduit to strut clamp 0 CH8-45EG Conduit to strut clamp 0 CX8-08EG Conduit to strut clamp without saddle 00 CX8-0EG Conduit to strut clamp without saddle 00 CX8-25EG 2 4 Conduit to strut clamp without saddle 00 CX8-5EG 2 4 Conduit to strut clamp without saddle 00 CX8-5PG Conduit to strut clamp without saddle 00 CX8-205EG Conduit to strut clamp without saddle 00 vailable in double or triple configurations. Example: Double CH28-04EG Triple CH8-04EG CX8-08EG C-08 Universal Pipe Strap EZ-Strap Fits EMT, IMC or rigid conduit Size range 2" through 2" Can be used on 2" or 5 8" channel Saves inventory dollars Corrosion-resistant GoldGalv hardware finish One-piece construction means no assembly required Installs directly over conduit for easy installation 50% reduction of installation time No twisting required to install Slotted hex head screw CONDUIT OR PIPE SIZE STEEL O.D. SIZE CT. NO. (EMT, I.M.C., RIGID) (IN.) STRP THICKNESS (IN.) STD. CTN. C-08-/2 2 6 ga C-08-/4 4 6 ga C-08-6 ga C-08--/4 4 4 ga C-08--/2 2 4 ga C ga CT. NO. Counter Bed CT. NO. Extended Bed CT. NO. Double Bed CB8 Counter Bed STD. CTN. CB8-04PG 00 CB8-055PG 00 CB8-00PG 00 CB8-090PG 00 CB8-0PG 00 STD. CTN. EB8-04PG 00 EB8-055PG 00 EB8-00PG 00 EB8-090PG 00 EB8-0PG 00 STD. CTN. DB8-04PG DB8-055PG CT. NO. EB8 Extended Bed Counter Bed EB8 Extended Bed DB8 Double Bed NOTE: Not sold in pairs. CT. NO. Extended Bed DB8 Double Bed CT. NO. Double Bed STD. CTN. CB8-40PG 00 CB8-5PG 00 CB8-200PG 00 CB8-250PG 00 CB8-00PG 00 STD. CTN. EB8-40PG 00 EB8-5PG EB8-200PG EB8-250PG EB8-00PG STD. CTN. DB8-00PG DB8-090PG D-40

41 Pipe Straps, Conduit Clamps & Hangers Cable Clamps (continued) C-55 Porcelain Cable Clamps Hole Size C-55 HOLE SIZE STD. CT. NO. (IN.) (IN.) CTN. C C-55-B C-55-C C C C-55-2B C-55-2C C C C-55-B C-55-C C C C-55-4B C-55-4C C C C-55-5B C-55-5C C C C-55-6B C-55-6C C C C-55-B C-55-C C C C-55-8B C-55-8C C-55-8D C-55-8E C-55-8F Finish GoldGalv brand with bronze hardware. lso fits 2" wide channel. C-55 TPE n easy-to-use one-piece insulator made from Sarlink 49D, a flame retardant, high hardness grade TPE polymer that is UL Listed. The tapered flange of the insulator insures complete isolation and protection of the cable. Options include a Stainless Steel Clamp and hardware or an Electro-Galvanized Clamp with Everdur nut and bolt. Non-breakable TPE material Exceptional chemical resistance Dielectric strength of 640 Volts per mil Stainless Steel Clamps Type 04 or 6 Electro-Galvanized Steel Clamps with Everdur Nut and Bolt Flame-retardant TPE insulator Excellent UV resistance HOLE SIZE CT. NO. (IN.) (IN.) C55 TP 8.6 C-55-B-TP 2.6 C-55-C-TP C-55-2-TP 4.86 C-55-2-TP 8.86 C-55-2B-TP.86 C-55-2C-TP 8.86 C-55--TP C-55--TP C-55-B-TP C-55-C-TP C-55-4-TP C-55-4-TP C-55-4B-TP C-55-4C-TP C-55-5-TP C-55-5-TP Hole Size HOLE SIZE CT. NO. (IN.) (IN.) C-55-5B-TP C-55-5C-TP C-55-6-TP C-55-6-TP C-55-6B-TP.86 C-55-6C-TP 8.86 C-55--TP C-55--TP C-55-B-TP C-55-C-TP C-55-8-TP C-55-8-TP C-55-8B-TP C-55-8C-TP C-55-8D-TP C-55-8E-TP C-55-8F-TP D-4

42 Pipe Straps, Conduit Clamps & Hangers Pipe Clamps HS Series Two-Hole Pipe Strap C-20, C-20SS Extension Riser Clamp STD. CT. NO. PIPE SIZE (IN.) CTN. HS HS HS HS HS HS HS HS HS HS Standard Finish Galvanized. Carbon steel. Specify pipe size and catalog number. For stainless steel, add suffix ss. HS Series One-Hole Pipe Straps Designed for the support or steadying of vertical pipe risers. It is made of carbon steel and is designed to hold tight to the pipe, transmitting the load to the structure through the ears on each end. When possible, the clamp should be placed under a coupling, hub or lugs welded to the pipe. C-20, C-20SS NOTE: This product is not designed to be supported with rods. Install using the maximum suggested torque values shown in the Technical Section of this catalog. Material: Carbon Steel. Compliance: Federal Specification --92 Type 8, MSS-SP-69 (Type 8) and BSPSS-BS94. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify catalog number, finish and pipe size. C-20, C-20SS STD. CT. NO. PIPE SIZE (IN.) CTN. HS HS HS HS0 500 HS HS HS HS HS08 25 HS HS For stainless steel, add suffix ss. PIPE MX. WT. CT. NO. SIZE (IN.) LOD (LBS.) (IN.) ECH C-20-/ C-20-/ C C-20--/ C-20--/ C C-20-2-/ C C-20--/ C C , C , C , C , C , C , C , C , C , C , D-42

43 Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) C-20L Offset Pipe Clamp CX-25 Extended Offset Pipe Clamp The Offset Pipe Clamp is used on pipe lines running at a fixed distance from a wall or floor. The standard clearance is two inches from the O.D. of pipe to the face of the surface. Non-standard clearances can be fabricated upon request. Material: Carbon Steel. Load Rating: Up to 650 F (4 C). Finish: Ordering: C Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Specify pipe size, catalog number and finish. C-20L PIPE MX. LOD B C WT. ECH CT. NO. SIZE (IN.) (LBS.) (IN.) (IN.) (IN.) (LBS.) C-20L-/ C-20L-/ C-20L C-20L--/ C-20L--/ C-20L C-20L-2-/ C-20L C-20L C-20L C-20L C-20L C-20L-0 0, C-20L-2 2, B Designed to attach directly to piping where the exact distance between the structure and the pipe cannot be determined until the piping is in place. The extended legs can be modified in the field to suit the location. Legs of longer lengths can be furnished on order. Material: Carbon Steel. Finish: Standard Finish Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify pipe size, catalog number and finish. PIPE B WT. ECH CT. NO. SIZE (IN.) (IN.) (IN.) (LBS.) CX-25-/ CX-25-/ CX-25-/ CX CX-25--/ CX-25--/ CX CX-25-2-/ CX CX CX CX CX CX CX CX CX-25 B C-20P PVC Coated Riser Clamp The C-20P is normally used for the support of uninsulated vertical piping where no movement will occur. PVC coating the contact surface prevents galvanic corrosion with the pipe. Please use our C-20 for carbon steel piping or CT-20 for copper tubing requirements. NOTE: This product is not designed to be supported with rods. Install using the maximum suggested torque values shown in the Technical Section of this catalog. Material: Carbon Steel. Compliance: Federal Specification --92 Type 8, MSS-SP-69 T400 F / 600 C. Finish: Polyvinyl Chloride. Ordering: Specify pipe size and catalog number. 4" C-20P PVC Coating 4" C-20P PIPE MX. WT. ECH CT. NO. SIZE (IN.) LOD (LBS.) (IN.) (LBS.) C20P-/ C-20P-/ C-20P C-20P--/ C-20P--/ C-20P C-20P-2-/ C-20P C-20P D-4

44 Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) CT-20 Copper Riser Clamp Normally used for the support of uninsulated vertical tubing where no movement will occur. Please use C-20 for carbon steel piping or C-20P for plastic coating requirements. NOTE: This product is not designed to be supported with rods. Install using the maximum suggested torque values shown in the Technical Section of this catalog. Material: Carbon Steel. Compliance: Federal Specification --92 Type 8, MSS-SP-69 Type 8. Finish: Copper. Ordering: Specify tubing size and catalog number. 4" 4" CT-20 C-24 Ductile Iron Pipe Clamp Can be used to secure mechanical joint piping or socket fittings together to prevent separation under pressure either under or above ground, vertically or horizontally. If using in this fashion, two (2) W-24 Socket Clamp Washers and Figure Rods are also required, but must be ordered separately. The C-24 may also be used to support and guide vertical Ductile Iron pipe. Materials: Carbon Steel. Finish: Ordering: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Specify pipe size, catalog number and finish. C-24 CT-20 TUBE SIZE MX. LOD WT. ECH CT. NO. (IN.) (LBS.) (IN.) (LBS.) CT-20-/ CT-20-/ CT CT-20--/ CT-20--/ CT CT-20-2-/ CT CT-20--/ CT CT CT , C-24 PIPE SIZE CTUL WSHER WT. ECH CT. NO. (IN.) PIPE O.D. (IN.) SIZE (IN.) (LBS.) C C C C C C C C C C C C D-44

45 Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) C-25 Two-Bolt Pipe Clamp Designed to suspend cold or hot pipe lines where little or no insulation is required. The C-25 is usually used with an E-20- Weldless Eyenut or E-5 Welded Eyerod. See Figure 298 heavy-duty Two-Bolt Clamp when higher loads are required. We will also design to meet special requirements such as special pipe sizes. Rated Loads are for up to 50 F (99 C). Material: Carbon Steel. Compliance: Finish: Ordering: C-25 Federal Specification --92 Type 4, MSS-SP-69 Type 4 and BSPSS-BS94. Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify catalog number, finish and pipe size. lso, include any special requirements for C-25. C-26 MXIMUM LOD ROD TKE WT. PIPE SIZE 650 F/ 50 F/ C OUT D E F ECH CT. NO. (IN.) 4 C 4 C (IN.) (IN.) (IN.) (IN.) (LBS.) C25 / C-25-/ C C-25--/ C-25--/ C , C-25-2-/2 2 2, C-25-, C , C , C ,65, C ,65, C ,490 2, C ,490 2, C ,490 2, C ,490 2, C ,060 2, C ,060 2, C ,060 2, C ,500, F C D D E E C D-45

46 Pipe Straps, Conduit Clamps & Hangers Pipe Clamps (continued) C-26 Three-Bolt Pipe Clamp Designed for hot-insulated pipe lines up to 50 F. The spacer on the top inner bolt provides uniform space for the connecting eyerod or weldless eyenut. We will also design to meet special requirements such as special pipe sizes. Rated Loads are for up to 50 F (99 C). Material: Carbon Steel. Compliance: Federal Specification --92 Type, MSS-SP-69 Type and BSPSS-BS94. Finish: Ordering: C-26 Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify catalog number and pipe size. lso, include any special requirements. PIPE MXIMUM LOD TKE WT. SIZE 650 F/ 50 F/ B C D OUT E F H ECH CT. NO. (IN.) 4 C 99 C (IN.) (IN.) (IN.) (IN.) (IN.) (IN.) (LBS.) C-26-/ C-26-/ C C-26-/ C-26--/4 4,545, C ,545, C-26-2-/4 2 4,545, C-26-,545, C ,500 2, C ,500 2, C ,865 2, C ,865 2, C ,240 2, C ,240 2, C ,00, C ,00, C ,00, C ,500 4, C ,490 4, C ,500 6, C ,0500 9, Standard Finish GoldGalv unless otherwise stated. F C E B C-26 D H D-46

47 Pipe Straps, Conduit Clamps & Hangers Pipe Clamps -26, lloy Three-Bolt Pipe Clamp Designed for hot-insulated pipelines. The spacer on the top inner bolt provides uniform space for the connecting eyerod or weldless eyenut. Temperature range: above 50 F (99 C) to 050 F (566 C). Material: Chrome Molybdenum Steel, STM -8 Grade 22. Compliance: Federal Specification --92 Type, -26 MSS-SP-69 Type and BSPSS-BS94. Ordering: Specify catalog number and pipe size. -26 PIPE SIZE MXIMUM LOD B C D TKE OUT E F H WT. ECH CT. NO. (IN.) 950 F/50 C 000 F/58 C 050 F/566 C (IN.) (IN.) (IN.) (IN.) (IN.) (IN.) (LBS.) -26-/ / /2 2,400, ,400, /2 2 2,400, ,400, ,00,600, ,00,600, ,600,800, ,600,800, ,000 2,00, ,000 2,00, ,900 2,800 2, ,900 2,800 2, ,800 2, ,000,200 2, ,500,500 2, Pipe Hangers C-0, C-0F, C-0P, C-0SS Designed to support non-insulated, stationary lines from above, allowing for approximately " to 2" of vertical adjustment after the pipe is in place. The lower nut (not furnished) adjusts the pipe line to the proper elevation, the top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. Rated Loads are for up to 650 F (4 C) for carbon steel. Maximum PVC temperature is 40 F (60 C). Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). F Material: Carbon Steel (lso available in Stainless Steel as C-0SS). Compliance: Federal Specification --92 Type, MSS-SP-69 Type, BSPSS-BS94, UL and FM. Finish: Standard Finish GoldGalv, Black B (add suffix -B ), Electro-Galvanized (add suffix -EG ). C Ordering: Specify catalog number, finish and pipe size. C-0 C E B D H E PIPE MX. B C ROD TKE WT. ECH CT. NO. SIZE (IN.) LOD (LBS.) (IN.) (IN.) (IN.) OUT E (IN.) (LBS.) C-0-/ C-0-/ C C-0--/ C-0--/ C C-0-2-/2 2 2, C-0-, C-0--/2 2, C-0-4 4, C-0-5 5, C-0-6 6, PIPE MX. B C ROD TKE WT. ECH CT. NO. SIZE (IN.) LOD (LBS.) (IN.) (IN.) (IN.) OUT E (IN.) (LBS.) C-0-2, C , C-0-0 0, C-0-2 2, C , C , C , C , C , C , C , D-4

48 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) CL-0 Light-Duty Clevis Hanger CTL-0 Copper Clevis Hanger Designed to support non-insulated, stationary lines from above, allowing for approximately " to 2" of vertical adjustment after the pipe is in place. The lower nut (not furnished) adjusts the pipe line to the proper elevation, the top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. Material: Carbon Steel. Compliance: Federal Specification --92 Type, MSS-SP-69 Type. Finish: Ordering: CL-0 Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify catalog number, finish and pipe size. C B CL-0 PIPE SIZE MX. LOD B C E WT. ECH CT. NO. (IN.) (LBS.) (IN.) (IN.) (IN.) (IN.) (LBS.) CL0 / CL-0-/ CL CL-0--/ CL-0--/ CL CL-0-2-/ CL CL-0--/ CL E Designed to support non-insulated, stationary copper tubing lines from above, allowing for approximately " to 2" of vertical adjustment after the tubing is in place. The lower nut (not furnished) adjusts the pipe line to the proper elevation. The top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. Material: Carbon Steel. Compliance: Federal Specification --92 Type, MSS-SP-69 Type and BSPSS-BS94. Rated Loads are for up to 650 F (4 C). Finish: Copper. Ordering: Specify tubing size and catalog number. C CTL-0 B CTL-0 PIPE SIZE MX. LOD B C ROD TKE WT. ECH CT. NO. (IN.) (LBS.) (IN.) (IN.) (IN.) OUT E (IN.) (LBS.) CTL0 / CTL-0-/ CTL CTL-0--/ CTL-0--/ CTL CTL-0-2-/ CTL CTL-0--/ CTL CTL CTL E D-48

49 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) ETL-0 Light-Duty Clevis Hanger ETL-0 Light-Duty Clevis Hanger E TUBING MTERIL DIMENSIONS (IN.) STD. CT. NO. SIZE (IN.) SIZE B C E F CTN. ETL0 /2 2 6 ga x 8 ETL-0-/4 4 6 ga x 8 ETL-0-6 ga x 8 ETL-0--/4 4 6 ga x 8 ETL-0--/2 2 6 ga x 8 ETL ga x 8 ETL-0-2-/ x 4 ETL-0-8 x 4 ETL-0--/2 2 8 x 4 ETL x 4 ETL x 4 ETL x 4 Standard Finish GoldGalv. Carbon Steel. Copper tube sized. For the suspension of stationary copper tubing lines. Order by Cat. No., tubing size. C L OF PIPE F B C D-49

50 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) CI-0 Clevis Hanger for Ductile Iron and.w.w.. Cast Iron Pipe Designed to support non-insulated, stationary ductile iron and.w.w.. cast iron lines from above, allowing for approximately " to 2" of vertical adjustment after the pipe is in place. The lower nut (not furnished) adjusts the pipe line to the proper elevation. The top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. Material: Carbon Steel. Compliance: MSS-SP-69 Type, --92 Type. Finish: Ordering: CI-0 Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify pipe size, catalog number and finish. PIPE MX. DIMENSIONS (IN.) ROD TKE WT. ECH CT. NO. SIZE (IN.) LOD (LBS.) B C OUT E (IN.) (LBS.) CI-0-4 4, CI-0-6 6, CI , CI-0-0 0, CI-0-2 2, CI , CI , CI , CI , CI , C B CI-0 E C L D-50

51 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) C- J Pipe Hanger Standard Finish GoldGalv brand Complies with Specification MSS SP 58, Type 5. Sizes through 5" conform to Ca. Code Title 24, Div. T22 for seismic restraint bracing. Standard Felt Lined Plastic Coated C-F Felt-Lined J Pipe Hanger Standard Finish GoldGalv brand vailable in sizes up to 8". C-P Plastic-Coated J Pipe Hanger Standard Finish GoldGalv brand Isolates hanger from glass and other piping for corrosion or cushioning purposes. vailable in sizes up to 4". Order by Cat. No. and pipe size. Hole provided for side mounting to wall as bracket. B F E D DI. C G PIPE BOLT SIZE ROD SIZE DIMENSIONS (IN.) SIZE G STOCK MX. REC. STD. CT. NO. (IN.) (IN.) B C D E F (IN.) (IN.) SIZE LODS (LBS.) CTN. C--/ ga x C--/ ga x C ga x C---/ ga x C---/ ga x C ga x C--2-/ ga x C ga x C---/ x C x C x C--6 6* x C--8 8* x *Hangers 6" and over have hole instead of slot. D-5

52 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) C-2 djustable Swivel Ring Designed for the support of non-insulated static pipe lines. The swivel nut is knurled to provide a gripping surface when adjusting the pipe elevation. Compliance: Federal Specification --92 Type 0, MSS SP-69 Type 0, UL Listed and FM pproved ( 4" through 8"). We also offer Swivel Ring hangers that are for Copper Tubing (CT-2), PVC coated (C-2-P) and for NFP requirements (C-2-NFP) in this catalog. Material: Carbon Steel. Finish: Standard Finish Pre-Galv, Black (add suffix -B ). Electro-Galvanized (add suffix -EG ). Ordering: Specify pipe size, catalog number and finish. C-2 PIPE SIZE MX. LOD DIMENSIONS (IN.) WT. ECH CT. NO. (IN.) (LBS.) B D E (LBS.) C-2-/ C-2-/ C C-2--/ C-2--/ C C-2-2-/ C C-2--/ C-2-4 4, C-2-5 5, C-2-6 6, C-2-8 8, Standard Finish: Pre-Galv only. dd F suffix for felt lining. E C-2 B D D-52

53 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) C-2-P PVC-Coated djustable Swivel Ring Designed for the support of non-insulated static pipe lines and to protect the pipe from coming into direct contact with the hanger by having the contact surface PVC coated. The swivel nut is knurled to provide a gripping surface when adjusting the pipe elevation. C-2-NFP NFP Swivel Ring Designed for the support of non-insulated static pipe lines. The swivel nut is knurled to provide a gripping surface when adjusting the tubing elevation and is tapped to the reduced rod standards of NFP. Compliance: Federal Specification --92 Type 0, MSS SP-69 Type 0, UL Listed and FM pproved ( 4" through 8"). We also offer Swivel Ring hangers that are for Copper Tubing (CT-2) and for NFP requirements (C-2-NFP) in this catalog. Operating temperature should not exceed 40 F / 60 C. Material: Carbon Steel. Finish: Ordering: C-2-P Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify pipe size and catalog number. PIPE MX. LOD DIMENSIONS (IN.) WT. CT. NO. SIZE (IN.) (LBS.) B D E ECH (LBS.) C2P / C-2-P-/ C-2-P C-2-P--/ C-2-P--/ C-2-P C-2-P-2-/ C-2-P C-2-P--/ C-2-P-4 4, C-2-P-5 5, C-2-P-6 6, C-2-P-8 8, E C-2-P B D Compliance: Federal Specification --92 Type 0, MSS SP-69 Type 0, UL Listed and FM pproved ( 4" through 8") and NFP standards. We also offer Swivel Ring hangers that are for standard commercial pipe (C-2), copper tubing (CT-2) and PVC coated (C-2-P) in this catalog. Material: Carbon Steel. Finish: Ordering: C-2-NFP Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify pipe size, catalog number and finish. PIPE MX. LOD DIMENSIONS (IN.) WT. CT. NO. SIZE (IN.) (LBS.) B D E ECH (LBS.) C-2-NFP-/ C-2-NFP-/ C-2-NFP C-2-NFP--/ C-2-NFP--/ C-2-NFP C-2-NFP-2-/ C-2-NFP C-2-NFP--/ C-2-NFP C-2-NFP-5 5, C-2-NFP-6 6, C-2-NFP-8 8, E C-2-P B D D-5

54 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) CT-2 Copper Tubing Swivel Ring Designed for the support of non-insulated static copper tubing lines. The swivel nut is knurled to provide a gripping surface when adjusting the tubing elevation. Compliance: Material: Finish: Ordering: CT-2 Federal Specification --92 Type 0, MSS SP-69 Type 0. We also offer Swivel Ring hangers that are for carbon steel pipe (C-2), PVC coated (C-2-P) and for NFP requirements (C-2-NFP) in this catalog. Carbon Steel. Copper. Specify copper tubing size. PIPE MX. DIMENSIONS (IN.) WT. ECH CT. NO. SIZE (IN.) LOD (LBS.) B D E (LBS.) CT2 / CT-2-/ CT CT-2--/ CT-2--/ CT CT-2-2-/ CT CT-2--/ CT CT-2-5 5, CT-2-6 6, Standard Finish GoldGalv unless otherwise stated. E CT-2 B D ET-2 Copper Sized djustable Ring Standard Finish GoldGalv barrier for separation of dissimilar metals. vailable in sizes 2" through 2". Sized for Copper Tubing. TUBING ROD DIMENSIONS (IN.) STOCK MX REC. STD. CT. NO. SIZE (IN.) SIZE (IN.) B C SIZE LOD (LBS.) CTN. ET2 / ga x ET-2-/ ga x ET ga x ET-2--/ ga x ET-2--/ ga x ET ga x ET-2-2-/ * ga x ET ga x ET-2--/ ga x ET * ga x 4, ET ga x 4, ET ga x 4, " CT filled with water weighs less than 2" IP filled with water, 4" CT less than 2" IP with water. 2 2" CT available with 2" thread and 4" CT available with 5 8" thread for Government Specs. D-54

55 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) M-8, M-8-B Extension Ring Hanger M-8 (Rod Tapped Electro-Galvanized) M-8-B (Rod Tapped Plain Finish) This split ring hanger is designed for the support of non-insulated stationary pipe lines. lso available in a two-screw design. The MT-42-R Ceiling Plate is normally used with this product. Material: Malleable Iron. Finish: Standard Finish EG (silver), Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Compliance: Federal Specification --92 Type 2, MSS-SP-69 Type 2. Ordering: Specify pipe size and catalog number. PIPE MX. PIPE ROD WT. SIZE LOD SIZE SIZE ECH CT. NO. (IN.) (LBS.) (IN.) (IN.) B (IN.) (LBS.) M-8-/ M-8-/ M-8-/ M M-8--/ M-8--/ M M-8-2-/ M M Standard Finish EG (silver). MT-8 Copper Extension Ring Hanger This split ring hanger is designed for the support of non-insulated copper tubing lines. The MT-8 is furnished tapped for bolt thread and is used with the MT-42-R Ceiling Plate. lso available in a two-bolt design. Material: Malleable Iron. Finish: Copper. For Electro-Galvanizing please see M-8. Compliance: Federal Specification --92 Type 2, MSS-SP-69 Type 2. Ordering: Specify tube size and catalog number. M-8 B TUBE MX. ROD WT. SIZE LOD SIZE ECH CT. NO. (IN.) (LBS.) (IN.) B (IN.) (LBS.) B MT8-/ MT-8-/ MT-8-/ MT-8-5/ MT-8-/ MT MT-8--/ MT-8--/ MT MT-8-2-/ MT MT-8 D-55

56 Pipe Straps, Conduit Clamps & Hangers Pipe Hangers (continued) Seismic Bracing (Consult Superstrut Seismic Hanger bulletin for additional information.) 4" 5 8" 4 2" 4" 5 8" C49N Seismic Brace,500 lb. load safety factor ll braces have plastisol coating on the flat member. Plastisol insulates against vibration noise transmission and eliminates rattle at the connection points. 2 Holes 9 6" Dia. Standard Finish GoldGalv brand. pproved for seismic applications. 4" 4" 5 8" 5 8" 4 2" 2 8" 2 Holes 9 6" Dia. 5 8" C49N 5/8 Seismic Brace,650 lb. load safety factor 4 4" 6" 2 Holes 9 6" Dia. C-49-N--/8 Seismic Brace,650 lb. load safety factor 2" 6" Dia. 6" Dia. 4" 5 8" 4 2" 2 8" 2 Holes 9 6" Dia. 5 8" C49N /8 Seismic Brace,650 lb. load safety factor ES-42 Size: 2" x 4" Bolt Size: 2" Seismic bracing rod stiffener connector 5 6" S-20 djustable Pipe Hanger PIPE ROD BOLT STOCK BOLT DESIGN STD. CT. NO. SIZE (IN.) SIZE (IN.) DJUSTMENT (IN.) CENTERS (IN.) SIZE (IN.) SIZE (IN.) LOD (LBS.) CTN. S20 / x S x S-20--/ x S-20--/ x S x S-20-2-/ x S x 4 2 4,00 0 S-20--/ x 4 2 4,00 0 S x 4 2 4,00 0 S x ,600 0 S x ,600 5 S x ,000 5 D-56

57 Pipe Straps, Conduit Clamps & Hangers PG-94 Pipe lignment Guide Designed to maintain the axial alignment of piping as it expands and contracts during operation. It is most typically installed adjacent to expansion joints and at reasonable distances between the expansion joint and the anchor point. Our Figures 00 and 00 also offer alternative means for your piping alignment needs. NOTE: Guides are not designed to carry dead weight loads. Maximum temperature is 50 F. B I Material: Finish: Carbon Steel. EG (Silver), Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify pipe size, insulation thickness, catalog number and finish. Example Catalog Number: PG94 T-2-/2 would be 2 2" pipe with 2" thick insulation. PG-94 DIMENSIONS (IN.) WT. ECH SIZE B C D E F G H (LBS.) SIZE THICKNESS OF INSULTION (IN.) NUMBER Standard Finish EG (silver). Insulation Thickness H Dia. 4 Holes PIPE SIZE (IN.) DIM. I MX. MVT E D M-8 C Insulation Thickness Table PRODUCT INSULTION FOR PIPE DESIGNTION THICKNESS (IN.) SIZES T 2 24 T T T T T T F G Pipe D-5

58 Pipe Straps, Conduit Clamps & Hangers Structure ttachments M-42-R, M-42-RB, MT-42-R Single Plate M-42-R (Rod Tapped Electro-Galvanized) M-42-RB (Rod Tapped Plain Finish) MT-42-R (Rod Tapped Copper Finish) Designed for attaching a rod to a wooden member. This part is normally used in conjunction with our M-8 Split Ring. Material: Malleable Iron. M-42-R is Carbon Steel. Ordering: Specify rod size and catalog number. M-42-R Ceiling Flange M-42-R, M-42-RB, MT-42-R ROD MX. DIMENSIONS (IN.) WT. ECH CT. NO. TP (IN.) LOD (LBS.) B C (LBS.) M-42-R-/ M-42-R-/ Standard Finish Black (B), EG (Silver) or Copper-Colored Epoxy Paint.. C-6-Side Clip Steel Bracket Clip Clip can be used to support piping 2" or smaller from the horizontal member of a C-6 Steel Bracket. The clip is composed of two steel plates and one bolt and nut. Tap M-42-R Rod Sizes: 8" & 2" C B Material: Finish: Carbon Steel. Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Ordering: Specify size number, catalog number and finish. ROD SIZE SIZE MX. LOD WT. ECH CT. NO. (IN.) (IN.) (LBS.) (LBS.) C-6-SIDE CLIP C-6-SIDE CLIP D-58

59 Pipe Straps, Conduit Clamps & Hangers Structure ttachments (continued) C-6 Light Welded Steel Bracket Designed to support up to 6" pipe. This bracket is for installation to walls as shown or inverted, and may require a backing plate. Holes for up to 4" rods are located at each end of the bracket to allow for use in either orientation. The C-6 Side Clip Steel Bracket Clip can be attached to the C-6 to support piping 2" or smaller. Please see the Figure 9 for more information. Compliance: --92 Type, MSS-SP 69 Type. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify size number, catalog number and finish. C-6 ROD MX. LOD DIMENSIONS (IN.) WT. ECH CT. NO. TP (LBS.) B C (LBS.) C C C C-9-H Heavy Welded Steel Bracket Designed to support pipe from either above or below. Slotted construction allows for drop rod use along the length of the bracket. This bracket is for bolted installation to walls and may require a backing plate. Special steel brackets can be fabricated to customers loads and/or dimensions. Compliance: --92 Type, MSS-SP 69 Type. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify size number, catalog number and finish. " " C B D C H B " 4" 6" TYP () PLCS. L G C-6 F K L " C-9-H L One Bolt Hole in Size 0 Bracket 2" D 2" E J C-9-H MX. LOD DIMENSIONS (IN.) WT. ECH CT. NO. SIZE (LBS.) B C D E F G H J K L (LBS.) C-9-H-0 0, N C-9-H-, C-9-H-2 2, C-9-H-, C-9-H-4 4, C-9-H-5 5, D-59

60 Pipe Straps, Conduit Clamps & Hangers PG-95 Pipe Block " Standard Finish Black (B). 8" 2" Pipe ttachments H-5, H-5SS Standard U-Bolt Our standard U-Bolts are recommended for use as supports or guides for piping. They are supplied with four hex nuts. The H-5SS is recommended for support of stainless steel piping. Please specify the grade of stainless steel you require when ordering. Load Ratings shown are for Carbon Steel. PVC coating should not exceed 40 F / 60 C. Materials: Carbon Steel, Stainless Steel. Compliance: Federal Specification --92 Type 24, MSS-SP 69 Type 24, and BSPSS-BS94. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ), SS (add suffix SS), SS6 = 6. Side loads are given for the H-5 for a maximum temperature of 650 F / 4 C. When the loading condition requires the simultaneous application of a normal load and side load, the following interaction equation must be used to determine if the H-5 can be used. (ctual Load / Maximum Design Load) + (ctual Side Load / Maximum Side Load). The result of this equation cannot exceed the value of.0 if the H-5 is to be used. Ordering: Specify pipe size, catalog number and finish. 6" Dia. H-5-/2 B E D C H-5 PIPE MX. LOD (LBS.) MX. SIDE WT. SIZE 650 F/ 50 F/ LOD (LBS.) DIMENSIONS (IN.) ECH CT. NO. (IN.) 4 C 99 C 650 F/4 C B C D E (LBS.) H-5-/ H-5-/ H H-5-/2 2,200, H-5-/4 4,200, H-5-,200, H-5--/4 4,220, H-5--/2 2,220, H-5-2 2,220, H-5-2-/ ,260 2, H-5-2,260 2, H-5--/2 2 2,260 2, H ,260 2, D-60

61 Pipe Straps, Conduit Clamps & Hangers Beam ttachments M-50 Side Beam Bracket Designed for bolted connections. G Compliance: --92 Type 4 and MSS-SP 69 Type 4. Material: Malleable Iron (Maximum Temperature 450 F / 22 C). Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify rod size and catalog number. F F ROD MX. LOD (LBS.) WT. SIZE WITH WITH BOLT DIMENSIONS (IN.) ECH CT. NO. (IN.) LG SCREW TO STEEL C D F G (LBS.) M-50-/ M-50-/ , M-50-5/ , M-62 Side Beam Connector Designed for use on buildings of wood construction. They can be secured to the side of beams or joists by means of our Figure 66 Drive Screws (ordered separately). Material: Finish: Malleable Iron. Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify size, catalog number and finish. SIZE MX. LOD DIMENSIONS (IN.) WT. ECH CT. NO. (IN.) (LBS.) B C (LBS.) M-62-/8 8 rod M-62-/2 2 rod M-62-/4 4 pipe C-4 djustable Beam ttachment For attachment to timber with coach screws or to the bottom of beams with bolts C B B D M-50 M-62 D C E F C C-4 ROD HOLE STOCK DESIGN SIZE SIZE DIMENSIONS (IN.) SIZE LOD STD. CT. NO. (IN.) (IN.) B C D E F (IN.) (LBS.) CTN. C-4-/8B 8B x C-4-/2B 2B x 2,0 50 C-4-5/8B 5 8B x 2,80 50 C-4-/4B 4B x 2 2,0 50 C-4-/8B 8B x 2,0 50 Standard Finish Black (B). Order by Cat. No., rod size. D-6

62 Pipe Straps, Conduit Clamps & Hangers Rods and Rod ttachments F-2 Turnbuckle M-29 Extension Piece Used to connect right- and left-hand threaded rods together and provide for adjustment. Material: Forged Steel. Compliance: Federal Specification --92 Type, MSS-SP 69 Type and BSPSS-BS94. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify catalog number, finish and rod size. F-2 F-2 ROD MX. LOD (LBS.) SIZE 650 F/ B WT. ECH CT. NO. (IN.) 4 C (IN.) (LBS.) F-2-/ F-2-/2 2, F-2-5/8 5 8, F-2-/4 4 2, F-2-/8 8, F-2-4, F-2--/4 4 8, F-2--/2 2, F-2--/4 4 5, F , F-2-2-/ , F-2-2-/2 2 2, B 6" " Rod Take Out Designed for attaching rods to the M-2-EXT Clamp and similar types of attachments. Material: Malleable Iron. Compliance: Federal Specification --92 Type 0, MSS-SP-69 Type 0 when used with a Figure 82. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify rod size, catalog number and finish. M-29 M-29 ROD SIZE MX. LOD DIMENSIONS (IN.) WT. ECH CT. NO. (IN.) (LBS.) B C G H (LBS.) M-29-/ M-29-/2 2, M-29-5/8 5 8, M-29-/4 4 2, M-29-/8 8 2, C B H D-62

63 Pipe Straps, Conduit Clamps & Hangers Structure ttachments C-80 W/OB, C-80 W/HWB Welded Beam ttachment Recommended for attachment to the bottom of beams when little or no pipe movement is expected. C-80 W/HWB is recommended for attachment to the bottom of beams, when pipe movement is expected. bolt and nut or pin is supplied. pin with cotters is normally supplied for rod sizes over ". E S C Compliance: Federal Specification --92 Type 22, MSS SP-69 Type 22 and BSPSS-BS94. Material: Carbon Steel. Finish: Ordering: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify catalog number, rod size and finish. C-80 W/OB, C-80 W/HWB Rod Size ROD MX. LOD (LBS.) ROD TKEOUT ROD TKEOUT WT. ECH (LBS.) SIZE 650 F/ BOLT OR C C-80 W/OB C-80 W/HWB H R S C-80 W/OB C-80 W/HWB CT. NO. (IN.) 4 C PIN SIZE (IN.) (IN.) E (IN.) E (IN.) (IN.) (IN.) (IN.) W/O B&N W B&N C-80-/ C-80-/2 2, C-80-5/8 5 8, C-80-/4 4 2, C-80-/8 8, C-80-4, C-80--/4 4 8, C-80--/2 2, C-80--/4 4 5, C , N/ C-80-2-/ , N/ C-80-2-/2 2 2, N/ C-80-2-/ , N/ C-80-50, N/ C-80--/4 4, N/ C-80--/2 2, N/ E R S C-80 C H D-6

64 Pipe Straps, Conduit Clamps & Hangers Beam Clamps C-55 Beam Clamp Designed to attach to the bottom of flanged beams. Normally used with the E-5 Eye Rod or E-20- Eye Nut. Material: Carbon Steel. Compliance: Federal Specification --92 Type 2, MSS-SP-69 Type 2. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro- Galvanized (add suffix -EG ), Thermoplastic (add suffix -TP ). Ordering: Specify clamp size, flange width, flange thickness, catalog number and finish. D C C-55 B C-55 CLMP MX. LOD DIMENSIONS (IN.) BOLT SIZE CT. NO. SIZE (LBS.) B C D (IN.) C C C C , C , C , C-55-5, WEIGHT ECH (LBS.) CLMP BEM WIDTH DIMENSION CT. NO. SIZE C C C C C C C D-64

65 Pipe Straps, Conduit Clamps & Hangers Beam Clamps (continued) M-2-H Steel Beam Clamp with Weldless Eyenut Beam Flange Width The M-2-H beam clamp with eyenut is used when welding to the structure is prohibited for supports where some movement is expected. The clamping effect is produced by the ice-tong action of the arms and is locked in place by the through bolt located just under the beam flange. Material: Carbon Steel with Forged Steel Eyenut. Compliance: Federal Specification --92 Type 28, MSS-SP-69 Type 28 and BSPSS-BS94. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify catalog number, rod size, clamp number and finish. M-2-H MX. MX. BODY MX. WT. CLMP LOD ROD SIZE BEM SIZE FLNGE ECH CT. NO. SIZE (LBS.) (IN.) WIDTH (IN.) THICKNESS (IN.) (LBS.) M-2-H- 2, M-2-H-2 2 4, M-2-H- 4, M-2-H-4 4 4, M-2-H-5 5 4, M-2-H-6 6, M-2-H-, M-2-H-8 8, CLMP BODY DIMENSIONS (IN.) CT. NO. SIZE SIZE (IN.) M-2-H M-2-H M-2-H M-2-H M-2-H M-2-H M-2-H M-2-H M-2-H E D-65

66 Pipe Straps, Conduit Clamps & Hangers Beam Clamps (continued) M-2-EXT djustable Beam Clamp Designed to attach to the bottom of flanged beams without requiring welding. Normally used with the M-29 Extension Piece (not furnished) up to a maximum 8" (M20) rod diameter. Loading is achieved through the clamp jaws while locking is accomplished by tightening the through-bolt located directly below the flange. Maximum flange thickness is 0.60 inches. Material: Malleable Iron. Compliance: Federal Specification --92 Type 0, MSS-SP-69 Type 0 when used with a Figure 5. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify catalog number and finish. Order M-29 separately if required. M-2-EXT M-2-EXT ROD TKE OUT MX. BEM FLNGE WIDTH B (IN.) MX. ROD LOD 2C WT. ECH CT. NO. SIZE (IN.) (LBS.) (LBS.) M-2-EXT-/ M-2-EXT-/2 2, M-2-EXT-5/8 5 8, M-2-EXT-/4 4, M-2-EXT-/8 8, D-66

67 Pipe Straps, Conduit Clamps & Hangers Rollers, Shields and Saddles C-28 Pipe Roller (Pair) Cast aluminum rollers, steel brackets Designed for standard saddles Order separately for each pair of rollers: Two 2" x 5 6" hex head cap screws, two 2" channel nuts Space to fit O.D. of pipe and wrapping djustable for radius up to 8" DESIGN MX OS B LOD STD. CT. NO. RDIUS (IN.) (IN.) (LBS.) CTN ,50 5 pair (0 pieces) C28 C ,50 5 pair (0 pieces) ,50 5 pair (0 pieces) ,50 5 pair (0 pieces) CR-29 Roller Support Used on steam or hot water systems where pipe is to be supported in tunnels, trenches, structural brackets and frames. djustment is made by raising and lowering the top nut on the legs and locked into position by tightening the lower nut. E B CR " 2-2" CR-29 C-89 C-89 C-89B C-89C C-89D C-89E PIPE SIZE " COV. 2" COV. 2" COV. 2 2" COV. " COV. 4" COV. OF ROLL H C D C28H Pipe Roller ssembly (Pair) Cast aluminum roller, steel brackets. Order separately for each pair of rollers: Two 2" x 5 6" hex head cap screws Two 2" channel nuts djustable to fit O.D. pipe 6" through 8". B PIPE SIZE B DESIGN STD. CT. NO. (IN.) (IN.) (IN.) LOD (LBS.) CTN ,920 5 pair (0 pieces) 8 6 8,920 5 pair (0 pieces) ,920 5 pair (0 pieces) C-28-H C28H ,920 5 pair (0 pieces) ,920 5 pair (0 pieces) ,920 5 pair (0 pieces) ,920 5 pair (0 pieces) Material: Finish: CR-29 Steel xle, Cast Iron Roll. Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify pipe size, catalog number and finish. PIPE SIZE MX. LOD DIMENSIONS (IN.) WT. ECH CT. NO. (IN.) (LBS.) C D E H (LBS.) CR CR-29-2-/ CR CR-29--/ CR CR CR , CR , CR , CR , CR , CR , D-6

68 Pipe Straps, Conduit Clamps & Hangers Pipe Rolls C-29 Harvard Roll Hanger Designed to support piping lines from above, allowing for vertical adjustment and axial movement in the piping. The lower nut (not furnished) adjusts the pipe line to the proper elevation. The top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. Material: Carbon Steel frame with a Cast Iron Roll. Do not exceed 450 F / 22 C at the contact point to the roll. Compliance: --92 Type 4 and MSS-SP-69 Type 4. Finish: Ordering: C-29 Black (add suffix -B ), Electro-Galvanized (add suffix -HDG ). For pipe with insulation and a pipe covering protection saddle the C-29 will have to be oversized to suit. Please see the table below showing the correct sizing for insulated pipe. Specify pipe size, catalog number and finish. DIMENSIONS (IN.) PIPE MX. ROD WT. SIZE LOD SIZE ECH CT. NO. (IN.) (LBS.) B C D E (LBS.) C C-29-2-/ C C-29--/ C C C C C C C C , C , C , C , C , C C-29 C-29 C-89 C-89 C-89B C-89C C-89D C-89E PIPE SIZE " COV. 2" COV. 2" COV. 2 2" COV. " COV. 4" COV. OF ROLL LC E D B D-68

69 Pipe Straps, Conduit Clamps & Hangers Pipe Rolls (continued) CR-29 Roller Chair RC-29 djustable Roll Support Designed for longitudinal movement of pipe where vertical adjustment is not required. lthough two bolts are supplied for installation, the chair can be alternatively welded in position. Material: Carbon Steel Chair and xle with Cast Iron Pipe Roll. Use a Figure when a Cast Iron Chair is required. Do not exceed 450 F / 22 C at the contact point to the roll. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). For pipe with insulation and a pipe covering protection saddle, the CR-29 will have to be oversized to suit. Please see the Table for the RC-29 which shows the correct sizing for insulated pipe. Ordering: Specify pipe size, catalog number and finish. CR-29 B C CR-29 PIPE MX. BOLT WT. SIZE LOD DIMENSIONS (IN.) SIZE ECH CT. NO. (IN.) (LBS.) B C D G (IN.) (LBS.) CR x 2.0 CR-29-2-/ x 2.40 CR x 2.60 CR-29--/ x CR x CR x 2.90 CR , x CR , x CR , x CR , x CR , x CR , x 4.90 CR , x CR , x CR , x D G Material: Cast Iron Pipe Roll and Sockets, Carbon Steel xle, Continuous Thread Rods and Hex Nuts. Do not exceed 450 F / 22 C at the contact point to the roll. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). For pipe with insulation and a pipe covering protection saddle, the RC-29 will have to be oversized to suit. Please see the table for the RC-29 which shows the correct sizing for insulated pipe. Ordering: Specify pipe size, catalog number and finish. RC-29 H PIPE MX. WT. SIZE LOD DIMENSIONS (IN.) ECH CT. NO. (IN.) (LBS.) B D H (LBS.) RC-29--/ RC-29--/ RC RC-29-2-/ RC RC-29--/ RC RC RC , RC , RC , RC , RC , RC , RC , RC , RC , RC , B D RC-29 D-69

70 Pipe Straps, Conduit Clamps & Hangers Pipe Rolls (continued) RC-29 djustable Roll Support Designed for longitudinal movement of pipe where vertical adjustment is required. lthough primarily used for support of the pipe, this component may also be placed over the pipe to act as a guide. Material: Cast Iron Pipe Roll and Sockets with a Carbon Steel xle. Do not exceed 450 F / 22 C at the contact point to the roll. Compliance: --92 Type 42, MSS SP-69 Type 4. Finish: Ordering: RC-29 Black (add suffix -B ). Electro-Galvanized (add suffix -HDG ). For pipe with insulation and a pipe covering protection saddle, the RC-29 will have to be oversized to suit. Please see the table below which shows the correct sizing for insulated pipe. Specify pipe size, catalog number and finish. DIMENSIONS (IN.) PIPE MX. ROD WT. SIZE LOD SIZE ECH CT. NO. (IN.) (LBS.) B D K (LBS.) RC RC-29--/ RC-29--/ RC RC-29-2-/ RC RC RC RC , RC-29-, RC , RC , RC , RC , RC , RC , RC , RC , RC , RC-29 PIPE SIZE OF COVERING PROTECTION SDDLE TO BE USED WITH RC-29 RC-29 C-89 C-89 C-89B C-89C C-89D C-89E PIPE SIZE " COV. 2" COV. 2" COV. 2 2" COV. " COV. 4" COV. OF ROLL B K D D-0

71 Pipe Straps, Conduit Clamps & Hangers Pipe Rolls (continued) S-0-C Chair and Roll Designed for longitudinal movement of pipe where vertical adjustment is not required. Because the chair is made of steel, it can be either welded or bolted in position. Material: Carbon Steel Chair and xle with Cast Iron Pipe Roll. Use a Figure when a Cast Iron Chair is required. Do not exceed 450 F / 22 C at the contact point to the roll. Compliance: Federal Specification --92 Type 44, MSS-SP-69 Type 44. Finish: Black (add suffix -B ). Electro-Galvanized (add suffix -HDG ). For pipe with insulation and a pipe covering protection saddle, the S-0-C will have to be oversized to suit. Please see the Table below showing the correct sizing for insulated pipe. Ordering: Specify chair number, catalog number and finish. S-0-C C K E N S D J P O S-0-C D P J Chair No. & Chair No. 2 thru 6 N E K S O C BRE C-89 C-89 C-89B C-89C C-89D C-89E CHIR PIPE " COV. 2" COV. 2" COV. 2 2" COV. " COV. 4" COV. NO. SIZE ,050, CHIR MX. LOD BRE PIPE DIMENSIONS (IN.) WT. ECH CT. NO. NO. (LBS.) SIZE (IN.) C D E J K M N O P S (LBS.) S-0-C S-0-C S-0-C-2 2 2, S-0-C-, S-0-C-4 4 4, S-0-C-5 5 6, S-0-C-6 6, S-0-C- 2, D-

72 Pipe Straps, Conduit Clamps & Hangers Pipe ttachments CR-86 djustable Pipe Support Used for support of piping from below without welding to the pipe, and consists of a steel saddle, nipple and pipe reducer. It connects to a threaded pipe standard and base. Rated loads are for up to 650 F (4 C). Materials: Reducer is Cast Iron, Pipe saddle and nipple are carbon steel. Compliance: Federal Specification --92 Type 9, MSS-SP-69 Type 9. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify pipe size, catalog number and finish. C-86 PIPE MX. DIMENSIONS (IN.) WT. SIZE LOD MIN. MX. ECH CT. NO. (IN.) (LBS.) B D E E (LBS.) C-86--/2 2 5, C , C-86-2-/ , C-86-5, C , C , C , C , C , C , C , C , C , C , C , C , C , E B C-86 D C L D-2

73 Pipe Straps, Conduit Clamps & Hangers Pipe Saddles and Pipe Shields C-89, C-89, C89B, C-89C, C-89D, C-89E Pipe Covering Protection Saddle The C-89 saddles are used to protect the insulation against damage and keep heat loss to a minimum. They are designed for " to 5" of covering. ll Saddles are 2" long with three tabs on each side for welding to pipe. Sizes 2" and larger have a welded-in center rib. Covering Thickness 2" Material: Carbon Steel (except C-89 and C-89-8 which are Chrome Molybdenum Steel). Compliance: Federal Specification --92 Type 9 or 9B, MSS-SP-69 Type 9 or 9B and BSPSS-BS94. Finish: Ordering: C-89 Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Specify catalog number and pipe size. Center Rib Sizes 2" & Larger Figure MX. CTUL PIPE COVERING COVERING MX. FIGURE (IN.) FIGURE 2 (IN.) WT. SIZE THICKNESS THICKNESS LOD ROLL ROLL ECH CT. NO. (IN.) (IN.) (IN.) (LBS.) SIZE B SIZE B (LBS.) C-89-/ , C-89-/ , C-89B-/ , C-89-6, C , C-89B , C-89--/4 4 8, C-89--/ , C-89B--/ , C-89C--/ , C-89--/2 2 6, C-89--/ , C-89B--/ , C-89C--/ , C , C , C-89B , C-89C , C-89D-2 2 6, C-89-2-/ , C-89-2-/ , C-89B-2-/ , C-89C-2-/ , C-89D-2-/ , B C-89 Figure 2 B D-

74 Pipe Straps, Conduit Clamps & Hangers Pipe Saddles and Pipe Shields C-89 (continued) MX. CTUL PIPE COVERING COVERING MX. WT. SIZE THICKNESS THICKNESS LOD FIGURE (IN.) FIGURE 2 (IN.) ECH CT. NO. (IN.) (IN.) (IN.) (LBS.) ROLL SIZE B ROLL SIZE B (LBS.) C-89-6, C , C-89B , C-89C , C-89D- 6, C , C , C-89B , C-89C , C-89D , C-89E , C , C , C , C , C-89B , C-89C , C-89D-5 5 6, C-89E , C , C , C , C , C-89B , C-89C , C-89D-6 6 6, C-89E , C , C , C , C , C-89B , C-89C , C-89D-8 8 6, C-89E , C , C , C , C , C-89B , C-89C , C-89D , C-89E , C , C , C , C , C-89B , C-89C , C-89D , C-89E , C , C , D-4

75 Pipe Straps, Conduit Clamps & Hangers Pipe Saddles & Pipe Shields Covering Thickness 2" Center Rib Sizes 2" & Larger B B C-89 (continued) Figure C-89 MX. CTUL PIPE COVERING COVERING MX. WT. SIZE THICKNESS THICKNESS LOD FIGURE (IN.) FIGURE 2 (IN.) ECH CT. NO. (IN.) (IN.) (IN.) (LBS.) ROLL SIZE B ROLL SIZE B (LBS.) C , C-89B , C-89C , C-89D-4 4 5, C-89E , C , C , C , C-89B , C-89C , C-89D-6 6, C-89E , C , C , C , C-89B , C-89C , C-89D-8 8, C-89E , C , C , C , C-89B , C-89C , C-89D-20 20, C-89E , C , C , C , C-89B , C-89C , C-89D-24 24, C-89E , C , Figure 2 D-5

76 Pipe Straps, Conduit Clamps & Hangers Pipe Saddles and Pipe Shields (continued) C-90 Insulation Shield Designed to protect the insulation and distribute the load at the hanger point. This item is usually used with our C-0 Clevis Hanger. pprovals: Federal Specification --92 Type 40, MSS-SP-69 Type 40. Material: Carbon Steel. Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ). Ordering: Specify hanger size and catalog number. Shield Size Selection Table PIPE SIZES 2 Insulation Thickness (Inches) * B 0B B 6 0B B 2B 8 C 4C 0 4C 5C 6C 2 6C C 9C 4 C 9C C-90 C-90 INSIDE CLEVIS HNGER LENGTH WT. ECH CT. NO. DIMETER (IN.) SIZE (IN.) (IN.) (LBS.) C C C C C C C C C C C-90-B C-90-2B C-90-C C-90-4C C-90-5C C-90-6C C-90-C C-90-8C M- Eye Socket Designed for attaching a rod to split ring type clamps. M- is only available in 4", 8" and 2" rod sizes. Material: Malleable Iron. Compliance: Federal Specification WW-H-E Type 6, MSS-SP-69 (Type 6). Finish: Plain, Copper. Ordering: Specify rod size and catalog number. ROD SIZE MX. LOD MX. B E WT. ECH CT. NO. (IN.) (LBS.) (IN.) (IN.) (LBS.) M--/ M--/ M--/2 2, M--5/8 5 8, M--/4 4 2, M--/8 8 2, B Max. Dia. M- Rod Size E D-6

77 Pipe Straps, Conduit Clamps & Hangers Rods and Rod ttachments How to Order Shield Size Selection Table Sizes of CL-0 OR C-0 Clevis PIPE CT. NO. SIZES D F D 2 Insulation Thickness (Inches) C-90-/2 2 * C-90-/ C C-90--/ C-90--/ C C-90-2-/ C C-90--/ C C B 0B B C B B 2B C C 4C C C 5C 6C C C C 8C C C 8C *For Unarco foam, specify X E-5 Lag Rod Designed for a vertical rod connection to wood. Material: Carbon Steel Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Ordering: Specify rod diameter, rod length, catalog number and finish E-5 PIPE SIZES For Use with Shields Outside of Insulation. Insulation Thickness (Inches) WT. ECH (LBS.) ROD MX. MIN. LENGTH (IN.) LENGTH DIMENSION L SIZE LOD MCHINE COCH CT. NO. (IN.) (LBS.) B C E-5-/ E-5-/ E-5-5/ Standard Finish GoldGalv, unless otherwise stated B E-5 L C D-

78 Pipe Straps, Conduit Clamps & Hangers Rods and Rod ttachments (continued) E-5 Machine Thread Eye Rod Welded Eyerods are designed to permit swing in the attachment component due to pipe movement. Material: Finish: Ordering: E-5 Carbon Steel. Larger rod diameters over 2 2", special materials and special eye dimensions can be furnished upon request Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Specify catalog number, finish, rod size, rod length and thread length if other than standard (IN.) B (IN.) Thread Length D (IN.) Load at (LBS.) 60,0,80 2,0,0 4,960 8,000,60 5,00 20,00 2,200, F/4 C Load at (LBS.) 540,00,60 2,420,60 4,420,40 0,0 4,000 8,460 24,260 29, F/99 C Standard Finish GoldGalv, unless otherwise stated B Specify E-5 D D-8

79 Pipe Straps, Conduit Clamps & Hangers Rods and Rod ttachments (continued) F- Forged Steel Clevis Used to connect rod ends with structural steel welding lug plates or lugs welded to pipe. It provides a pivot point and adjustment. It can be supplied with a pin as F-. Material: Forged Steel Compliance: Federal Specification --92 Type 4, MSS-SP 69 Type 4 and BSPSS-BS94 Finish: Ordering: F- ROD MX. LOD PIN/BOLT SIZE WT. ECH CT. NO. SIZE 650 F/4 C DI. NO. P (LBS.) F--/ F--/2 2, F--5/8 5 8, F--/4 4 2, F--/8 8, F-- 4, F---/4 4 8, F---/2 2, F---/4 4 5, F , F--2-/ , F--2-/2 2 2, Standard Finish GoldGalv, unless otherwise stated E-20- Forged Weldless Eyenut E-20- Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Specify catalog number, rod size, pin size, grip G and finish Used to connect rod ends with structural steel welded beam attachments or pipe clamps as a substitute for a welded eyerod. It provides a pivot point and adjustment. It can also be supplied tapped left hand as E-20-. Material: Forged Steel Compliance: Federal Specification --92 Type, MSS-SP 69 Type, and BSPSS-BS94 Finish: Standard Finish GoldGalv, Black (add suffix -B ), Electro-Galvanized (add suffix -EG ) Ordering: Specify catalog number, rod size and finish ROD TP MX. LOD WT. ECH CT. NO. 650 F/4 C F (LBS.) E-20--/ E-20--/2 2,0 0. E-20--5/8 5 8, E-20--/4 4 2,0.00 E-20--/8 8, E , E-20---/4 4 8, E-20---/2 2, E-20---/4 4 5, E , E / , E /2 2 2, Standard Finish GoldGalv, unless otherwise stated E Take Out P F- NOTE: Pins and Cotter Pins supplied when requested as Fig. F-. F C L E-20- Tap Grip D-9

80 Series 800 Surface Raceway and Lighting Systems Surface Raceway & Lighting Systems Electrical Raceway Superstrut channel together with snap in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories listed by Underwriters Laboratories are identified on the drawings. Electrical pplications Column Suitable for number of wires indicated when used as a raceway. lso suitable for number of wires indicated when installed to support and supply electric discharge type fixtures when raceway wiring is suitable for not less than 5 C. Column B Suitable for number of wires indicated when used as a raceway. lso suitable for number of wires indicated when installed to support electric discharge type fixtures when clearance of not less than 8" is provided between raceway and fixture and when wiring is suitable for 5 C. GoldGalv hardware finish is standard for all Superstrut products. This is a multi-process finish of electro-plated zinc, followed by goldcolored zinc dichromate to give excellent corrosion resistance and a superior paint base. See page D-4 for a complete description of the GoldGalv hardware finish. GoldGalv hardware finish will be furnished if no other finish is specified. Materials: Superstrut electrical raceway, fixture hanging channel, closure strip and accessories are cold formed from hot-rolled strip steel. Design Data: Deflections at various hanger rod spacings for raceway channels, based on 40 to 45 lbs. per fixture. UL Listed Channels -200 B KO B200L -200 L B PG C E KO H SS Maximum Number of Wires DEFLECTION CHNNEL T 0 FT. T 2 FT. T 4 FT " 2" 4" C-200 8" 4" * " 4" * DEFLECTION CHNNEL T 6 FT. T FT. T 9 FT. B-200 8" 9 6" 5 8" B-400 " 2" * *Not recommended for this spacing RCEWY WITH OR WITHOUT KO WIRE -200 B-200 E-200 SIZE -400 B-400 C-200 H-200 VG B B B B D-80

81 Surface Raceway & Lighting Systems Electrical pplications (continued) Surface Raceway Systems 822 Page D-8 B-888 Page D-84 H04 Page D- B-844 Page D Page D-8-85 Page D Page D-8 B-80 Page D Page D-8 B-885 Page D-84 8 Page D-8 Standard Finish GoldGalv brand B-866 Page D Page D-8 D-8

82 Surface Raceway & Lighting Systems Electrical pplications (continued) Standard Finish GoldGalv brand 802 Page D-8-89 Page D Page D-8 B-844 Page D Page D-8 B-288 Page D- B-888 Page D Page D Page D-8 E-45 Page D- ES-45 Page D P Page D- Order nuts separately 452TB Concrete Spot Insert Page D Side Beam Hanger Clip Page D-26 S-54 Swing Connector Page D Beam Clamp Page D-26 U-59 Ceiling Flange US-56 Beam Clamp Page D-26 U-569 Beam Clamp with Safety Rod Page D-29 D-82

83 Surface Raceway & Lighting Systems Fixture Fittings 2 2" 8" 2" 4" 6 UNF Thread * Listed -24- End Cap for -200 Channel " 8" 2 6" 802 Raceway Joiner with Reinforcing Plate furnished complete with nuts. STD. CT. NO. FOR CHNNEL CTN. 802 Series 25 B-802 B Series 25 E-802 E Series 0 H-802 H Series End Cap STD. CT. NO. FOR CHNNEL CTN B804 B C-804 C E-804 E H-804 H Tapped End Cap 2 ga for 4" or " Conduit. Furnished complete with 4" x 5 8" Flat Head Machine Screw and B-00-4" nut. STD. CT. NO. FOR CHNNEL CTN Series 25 H-809 H Series 25 8 Stud Nut For attaching fixture to Slot Down Channel or to Slot up Knockouts. Specific length. Hex Nut included. STD. CT. NO. FOR CHNNEL CTN. 8 -STR 4 x STR 4 x Channel Hanger Use hanger rod 8" or 2". Use with, B or C series single channel. 854 Channel Hanger Illustration showing -854 with nut and bolt furnished to attach to fluorescent fixture. Use with, B or C series channel. 85L Channel Hanger Long type for all series channel. 854L Channel Hanger Long Illustration showing -854-L with nut and bolt furnished to attach to fluorescent fixture. Long type for all series channel. 4" 4" 805 End Cap with Knockout KO for 2" conduit. Furnished complete with 4" x 5 8" flat Head Machine Screw and B-00-4" nut. STD. CT. NO. FOR CHNNEL CTN Series 25 H-805 H Series Raceway Jointer & Seal STD. CT. NO. (IN.) FOR CHNNEL CTN. 822* 6 Series 25 B-822* 8 B Series 25 C-822* 6 C Series * 892* 89* 890* 89 D-8

84 Surface Raceway & Lighting Systems Fixture Fittings (continued) * Listed 4" B80* Cast Conduit Connector To connect 2" or 4" conduit to raceway channel Furnished complete with stud nuts & hex nuts. Part has removable bushing to increase size from 2" to 4". B-866 2" Pipe thread 8" 2" 2" 4 4" B85 Swing Connector Nuts & bolts to clamp to channel included. For 2" or 4" conduit. 8" B-844* Steel Closure Strip 5 8" B-844-PC* Plastic Closure Strip When used as a raceway channel, it is normally installed with the slot up and after wiring is complete, the closure strip is installed. For all channels. Standard lengths 0 ft. B86* Spacer Clevis For use with B-866 wiring stud nuts. B868 Fiber Retainer for cables until closure strip is installed. B885 5 Swivel Nuts and bolts to clamp to channel included. For 2" or 4" conduit " B-880 B-88 " and 4" Porcelain Saddles B88* Single Outlet Complete unit including housing, standard SINGLE -wire, 5 mp., 25 Volt, NEM ground receptacle and cover plate. B888* Duplex Outlet Complete unit including housing, standard DUPLEX -wire, 5 mp., 25 Volt, NEM ground receptacle and cover plate. MX. CBLE STD. CT. NO. DIM. (IN.) CTN. B-880 B D-84

85 Special Metals Properties for Design Stainless Steel (Suffix SS/Type 04 and 6SS/Type 6) Superstrut stainless steel products are made from high-quality austenitic Type 04 and Type 6 material. Stainless steel contains large amounts of chromium and nickel, is non magnetic and offers superior corrosion resistance. Tolerant to hightemperature environments, Superstrut s stainless steel framing provides dependable support, resulting in reduced maintenance cost. The channel is roll-formed to shape when cold, enhancing its structural strength for the most rigid of applications. Stainless Steel Channel Elements of sections are the same as shown on pages D-04 D- for standard steel channel. Load ratings meet or exceed ratings for standard steel channel shown elsewhere in this catalog. dditional stainless steel and aluminum items are available. Contact your local Superstrut representative. Properties for Design luminum Channel (Suffix L) X 5 8" Y Y Span (IN.): 2, 8, 24, 0, 6, 42, 48, 54, 60, 2, 84, 96, 08 & 20. X.9 5 8" 2 ga. =.05" I Moment of Inertia S Section of Modulus r Radius of Gyration rea Calculations based on maximum fiber stress of 0,000 psi, maximum deflection /60th of span. For concentrated loads, multiply load by Typical Physical and Mechanical Properties and Characteristics lloy and Temper: 606-T6 Tensile Strength: Yield 25,000 PSI Ultimate 0,000 PSI Shear Ultimate: 9,000 PSI Elongation: (Percent in 2 inches) -2 Density: Lbs./Cu. Inch Modules of Elasticity: 0 X 06 PSI M 5 8" Y X X.5 Y X - X XIS Y - Y XIS SECTION I S R I S R MEMBER IN. 2 IN. 4 IN. IN. IN. 4 IN. IN B Safe Uniform Total Load Table (X-X XIS) SPN B-200-L -200-L -202-L (IN.) (LBS.) (LBS.) (LBS.) 2 540,490 4, , , , , , X 5 8" Y Y X 5 8" 4" D-85

86 Special Metals luminum Products (L Suffix) 5 8" 8" Series " deep channel and combination B " 8" B Series 5 8" 6" 8" -200-HS Slots 2" on center. Slot size 9 6" x 8" B " 5 8" 4" " 2 ga. 2 ga. -00 Regular Spring Nut 02 Rigid Conduit Pipe Strap B-00 Springless Nut D-86

87 Special Metals Type #04 Stainless Steel Products (SS Suffix) 5 8" 8" 5 8" Series 8" HS -200-HS B " 8" B Series 6" " B-400-HS -00 Regular Spring Nut B-00 Short Spring Nut B-00 Springless Nut E-42 Hex Head Cap Screw E-45 Standard Hex Nut EF-4 Fender Washer D-8

88 Special Metals Type #04 Stainless Steel Products (SS Suffix) (continued) B-24 E-4 Flat Steel Washer H-9 Rod Coupling B20 D C B ROD STD. CT. NO. SIZE (IN.) CTN. B-24-/ B-24-/ B-24-/ U50, U502 STD. CT. NO. FOR CHNNEL (IN.) CTN. U B-200 B-400 C-200 B-402 U C-202 H-200 Furnished complete Design Load U lbs. U lbs. C-5L Clamp with Lock Nut ROD DIMENSONS (IN.) DESIGN STD. CT. NO. SIZE (IN.) B C D LOD (LBS.) CTN. C-5L B205 H-04 Hanger rod Continuous threaded NTIONL CORSE THRED SIZE THREDS DESIGN STD. CT. NO. (IN.) PER INCH LOD (LBS.) CTN. 02 Pipe and Rigid or IMC Conduit Clamp H-04--/ H-04-/ H-04-/2 2,0 500 H-04-5/8 5 8, H-04-/ ,0 500 H-04-/8 8 9,0 500 H , Standard lengths 2' only 0 Series D-88

89 Special Metals Type #04 Stainless Steel Products (SS Suffix) (continued) 4 8" 2 2" 5 8" 2" 8" 6H Series 6H-B Series Conduit and Pipe Hanger 4 8" B20 5 8" 2 4" X20 5 8" B204 4" B " B206 2" 4 8" B20 X20 B2 2" 4" 9 5 2" 4 8" 2" 8" 2" 5 8" 2 2" B24 B29 W29 D-89

90 Special Metals Type #04 Stainless Steel Products (SS Suffix) (continued) 5 5 8" 2" 4 Holes 4" Dia. 5 8" B220 6" 2" 4" Dia. P-22 4 Holes 4" Dia. 45 2" 2 2" B225 6" 2" 6" 4 4" 4 4" P-22SQ 4 4" 6" 45 4" Dia. 6" 2 5 6" SPB-22 4" 6" P-25 " 6" 2" 6" 5 6" 2" 6" " 4 5 8" 4 4" P-25SQ 4 4" S-250 is in lengths: 6,2,8 & 24. May be installed inverted with no change in load ratings. Strut section made from half slot channel. -6 Cushioned Clamp Tube Series C-0 Series Standard Clevis C-20 C-25 C-2 Standard Ring Hanger D-90

91 Special Metals Type #6 Stainless Steel Products (T6SS Suffix) 5 8" 8" 5 8" 8" 5 8" 6" B Series Series 8" " -200-T6SS 8" B-400-HS-T6SS 2" B225 B20 2 4" -200-HS-T6SS 02 Pipe and Rigid or IMC Conduit Clamp H-04 Hanger rod Continuous threaded 2" B-400-T6SS 5 8" B " 4 8" 2" NTIONL CORSE THRED SIZE THREDS DESIGN STD. CT. NO. (IN.) PER INCH LOD (LBS.) CTN. H-04--/4SS H-04-/8SS H-04-/2SS6 2,0 500 H-04-5/8SS6 5 8, H-04-/4SS ,0 500 H-04-/8SS6 8 9,0 500 H-04-SS6 8 4, Standard lengths 2' only B20 B205 D-9

92 Special Metals White Painted Products for the Computer Industry (WH Suffix) 5 8" 8" 5 8" 8" 5 8" B Series Series 8" HS B-400 8" B-400-HS HS 4 8" 5 8" 2 2" 8" 2 4" 2 2" 6" 2" 8" B20 X20 B29 4 8" 4 8" 8" 2" 2" B20 W204 B205 D-92

93 Special Metals White Painted Products for the Computer Industry (WH Suffix) (continued) 8" 4" 8" 8" 4" " 4" 6" 2" 5c" W205 L W-205-R N-205 B-206 B-20 X " e" 5 8" 20 For attaching Series channel 8" 5 8" 5 8" 5 6" " 2" B-29 2" 4" 5 8" 45 " 2" 2" 2 5 6" 6" 5 8" N-29 B-220 B-22-WH D-9

94 Special Metals White Painted Products for the Computer Industry/Clean Room pplications (WH Suffix) 4 Holes 4" Dia. 5 8" 2" 5 6" B-24 ROD STD. CT. NO. SIZE (IN.) CTN. B-24-/ B-24-/ B-24-/ " P-22 4 Holes 4" Dia. 5 8" 6" 6" 4 Holes 4" Dia. 6" P-22SQ 2" 6" 6" 4 4" 4 4" 5 8" 5 8" 4 Holes 4" Dia. 6" 5 8" B25 4" P-25 2" 6" 4 4" 4 4" 4" 5 8" 4" 5 8" P-25SQ 804 NEOP WH 5 8" x 5 8" White Plastisol End-Cap B 804 NEOP WH 5 8" x 6" White End-Cap 5 8" 4 " 4" 4 " H804 NEOP WH 5 8" x 4" White Plastisol End-Cap SPB-844-PC White White Closure Strip For all channels D-94

95 Slotted ngle Metal Framing With Superangle, You Get Flexibility Simplicity Economy! Superangle Slotted ngle Metal Framing Create the support framing you need. Superangle is manufactured from structural-quality steel in three different sizes. The small sizes are 4 ga. steel, the larger size is 2 ga. steel. With this offering, an endless variety of metal framing requirements can be met, from light-weight supporting needs to larger shelving for inventory storage. One of the legs on all sizes is 5 8" wide, while the other is either 5 8", 2 8" or 8" long. Depending on the frame requirements, a single size can be utilized throughout, or the sizes can be interchanged to get the most efficient usage from the material. Installation time is reduced inventory space is minimal. Scribe marks are placed every 4", which saves planning, layout and cutting time and provides accuracy. The exclusive slot and hole pattern, repeated every ", is scientifically designed for ease of assembly. The proper nuts and bolts are included with the material to ensure fast and easy erection. Superangle Metal Framing is packaged in 0' and 2' lengths to minimize cutoffs and ensure maximum use of material. 0', 2' lengths of Superangle take up the same amount of space as one 2 x 4. standard package includes five pieces to a bundle, therefore handling and storage space are significantly reduced. The importance of cutting Superangle easily, quickly and accurately is the key to time-saving assembly. The Portable Cutter provides these advantages and makes layout and erection of any structure a light-work job. Finish is designed for long lasting durability. The standard GoldGalv hardware finish is applied to all Superangle products after rolling and punching of the holes. This provides you with a number of benefits. First, raw ends resulting from cuts will be protected by the sacrificial quality of zinc. Second, the edges of all holes are protected against formation of rust, to provide a call-back free installation. Third, the electro-galvanizing process provides an excellent bonding surface for paint if desired for aesthetic reasons. NOTE: Product is also available with Pre-Galvanized (PG) sections D-95

96 Slotted ngle Metal Framing Superangle Slotted ngle Metal Framing (continued) LENGTH FT. PER STD. CT. NO. (FT.) PKG. CTN. R ,000 R ,200 R ,000 R ,200 R ,000 R ,200 5 Lengths, 6 Nuts and Bolts Superangle ccessories Casters STD. STD. CT. NO. PKG. CTN. R RC 2 2 R SC 2 2 Portable Cutter R-RC Rigid Center R-60 4 Gauge 5 8" X 5 8" R-00 2 Gauge 8" X 5 8" Rigid & Swivel Casters Hard rubber composition 2" dia. with load rating of 225 lbs. per wheel. R Gauge 2 8" X 5 8" R-SC Swivel Caster STD. STD. CT. NO. PKG. CTN. R C R-C Portable Cutter Gusset Plate STD. STD. CT. NO. PKG. CTN. R GP R-GP Gusset Plate For extra-rigid assembly. Extra Nuts and Bolts PCKGE STD. CT. NO. 00 SETS CTN. R BN 5/8 8" 6 x 5 8" lg. 00 Use with R-60 & R-225 R BN /4 8" 6 x 4" lg. 00 Use with R-00 Extra Nuts and Bolts D-96

97 Metal Framing Engineering Data Design Data Metal Framing Channel Elements of Sections X W Y Y Single Channels X Z Double Channels Table Properties for Design: Single Channel Nominal Thickness (IN.) 2 ga. =.05 I Moment of Inertia 4 ga. =.05 S Section of Modulas 6 ga. =.060 r Radius of Gyration Z Nominal xis rea X-X XIS Y-Y XIS H W I S R Z I S R CT. NO. IN. IN. IN.2 IN.4 IN. IN. IN. IN.4 IN. IN B C E H B Table Properties for Design: Double Channel H X W Y Y X Z H X-X XIS Y-Y XIS H W I S R Z I S R CT. NO. IN. IN. IN.2 IN.4 IN. IN. IN. IN.4 IN. IN B C E H B Table 2 Load Ratings for 2" Strut Nuts used in Superstrut Channel SLIP PULL-OUT CHNNEL RESISTNCE STRENGTH NO. (LBS.) (LBS.) -200,500 2,000 C-200,500 2,000 B-200,400, ,000,400 B-400,000,400 Safety Factor of If connections will be subjected to dynamic or seismic loading conditions, contact Thomas & Betts Technical Services for design assistance. D-9

98 Metal Framing Engineering Data Design Loads for Channel Used as Beam or Column. Design Data Metal Framing Channel (continued) Table Beam Loads Table contains simple beam, uniformly-distributed loads calculated at 25,000 psi fiber stress. Beam loads are based on channel being loaded across the x-x axis. Loads are also listed at reduced deflections for long spans. Maximum 25,000 psi Stress Maximum allowable deflections and maximum uniform loads for all 25,000 psi fiber stress. Reduced Load for all /80 Span Deflection For moderate deflections on the longer spans, reduced loads are listed which will produce a deflection equal to /80 of the span. When maximum loads do not induce deflections exceeding /80 x the span length, reduced loads are not required. Reduced Load for /60 Span Deflection For very slight deflections on the longer spans, reduced loads are listed which will produce a deflection equal to /60 of the span. When maximum loads do not induce deflections exceeding /60 x the span length, reduced loads are not required. Concentrated Loads To obtain values for concentrated loads from Table, multiply uniform load by 0.5 and deflection by.25. Slotted, Punched or KO Channel Reduce load rating 5%. Long Span Deep Beams Support in a manner to prevent rotation at supports and tie between supports to prevent twist. Column Loads llowable column loads given are for uniform axial loading with pinned ends. For eccentric loading or other end conditions, reduce allowable loads according to standard engineering practice. Dynamic Loads llowable dynamic loads may be calculated by dividing the static loads shown in Table, by D-98

99 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Single Channel MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 2" Beam or Column , ,5 B , ,68 C , ,45 E , ,80 H , , , ,55 B ,950 8" Beam or Column , ,20 B ,058 C , ,90 E , ,482 H , , , ,4 B ,50 24" Beam or Column , ,842 B ,5 C , ,545 E , ,082 H , , , ,058 B ,000 0" Beam or Column , ,49 B ,465 C , , ,060 E , ,640 H , , ,5 B ,420 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-99

100 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Double Channel (Single Channels Welded Back-to-Back) MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 2" Beam or Column , B , ,0 C ,990 E ,62 H , ,250 B , ,90 8" Beam or Column ,609 B , ,440 C , ,40 E ,926 H , ,86 B , ,90 24" Beam or Column , ,94 B , ,60 C , ,890 E ,4 H , , ,426 B , ,50 0" Beam or Column , ,26 B , ,80 C , ,20 E , ,259 H , , ,9 B ,0 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-00

101 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Single Channel MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 6" Beam or Column , ,962 B ,498 C ,525 E , ,60 H , , ,46 B ,55 42" Beam or Column , ,466 B ,59 C ,945 E , ,698 H , , ,05 B ,060 48" Beam or Column ,94 B ,98 C ,25 E , ,092 H , , ,658 B ,580 54" Beam or Column ,69 B ,555 C ,650 E , ,2.50 0,505 H , , ,24 B ,250 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-0

102 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Double Channel (Single Channels Welded Back-to-Back) MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 6" Beam or Column , ,40 B , ,840 C , ,500 E , ,6 H , , ,46 B ,050 42" Beam or Column , ,65 B ,90 C , ,0 E , ,22 H , , , ,82 B ,00 48" Beam or Column , ,0 B ,640 C , ,890 E , ,0 H , , , ,22 B ,480 54" Beam or Column , ,6 B ,405 C , ,26.50,990 E , ,980 H , , , ,566 B ,580 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-02

103 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Single Channel MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 60" Beam or Column ,62 B C ,920 E , ,84 H , , ,92 B " Beam or Column ,2 B C ,45 E , ,2 H , , , B " Beam or Column ,46 B C ,485 E , ,509 H , ,.200 0, ,809 B " Beam or Column ,06 B C ,565 E ,99 H , , ,82 B When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-0

104 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Double Channel (Single Channels Welded Back-to-Back) MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 60" Beam or Column , ,8 B ,00 C , ,02.6,050 E , ,4 H , , , ,88 B ,640 66" Beam or Column , ,4.8,646 B ,055 C , ,00 E , ,45 H , , , , B ,840 2" Beam or Column , , ,500 B ,20 C , ,980 E , ,02 H , , , ,40 B ,220 84" Beam or Column , ,992 B ,00 C , ,60 E , ,99 H , , ,682 B ,0 When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-04

105 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Single Channel MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 96" Beam or Column ,08 B C ,960 E ,42 H , , ,65 B " Beam or Column ,456 B C E ,29 H , , ,08 B " Beam or Column B C E ,48 H , , B " Beam or Column C E H When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-05

106 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Double Channel (Single Channels Welded Back-to-Back) MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 96" Beam or Column , ,65 B C ,640 E , ,9.26 0,85 H , , ,95 B " Beam or Column , ,0 B C ,250 E , , ,599 H , , ,02 B " Beam or Column B C ,250 E , ,22. 6,946 H , , ,805 B " Beam or Column B C E , H , , B When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-06

107 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Single Channel MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 68" Beam or Column C E H " Beam or Column E H " Beam or Column E H " Beam or Column E H When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-0

108 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table Double Channel (Single Channels Welded Back-to-Back) MXIMUM /80 /60 DEPTH UNIFORM SPN SPN COL. CT. NO. (IN.) G. LOD DEFL. LOD DEFL. LOD DEFL. LOD 68" Beam or Column B C E ,94.040, H , , B " Beam or Column C E , H , , " Beam or Column C E , H , " Beam or Column C E H , When no numbers are shown, use the maximum uniform load. Deflections are given in inches; loads in lbs. D-08

109 Metal Framing Engineering Data Design Data Metal Framing Channel (continued) Table 4 Safe Bearing Loads for 5 8" Channel and Combinations SECTION RECOMMENDED LOD IN LBS. SECTION RECOMMENDED LOD IN LBS. SECTION RECOMMENDED LOD IN LBS , ,500 B-200 6,000 B-400,400 C-200 5,000 E-200 5,000 H-200 4,000 Safety factor of 2 2 B-202 Both ends supported. -200,500 lbs. -400,000 lbs. Both ends supported. -200,000 lbs lbs. -200, ,500 B-200 4,000 B-400 2,600 C-200,500 E-200,500 H-200 2,000 Table 5 Design Load Table for Typical Channel Connections Safety factor of 2 2 based on ultimate strength of the connection. Load diagrams indicate up to three design loads, for 2 gauge, 4 gauge and 6 gauge channel applications. 90 Fittings (when used in position shown). B-20 Both ends supported ,000 lbs. -400,500 lbs. Both ends supported. -200,000 lbs ,000 lbs , ,500 B-200 9,000 B-400 4,800 C-200 8,000 E-200 8,000 H-200 5,500 B lbs. B lbs. B-202 B-2 B-24 B-200,500 lbs. Both ends supported ,000 lbs ,000 lbs. Both ends supported. -200,500 lbs. -400,000 lbs. Flat Plate Fittings Both ends supported. -200,000 lbs lbs. B-206 B-205 B-26 B-204 B-25 D-09

110 Metal Framing Engineering Data Design pplications Cantilever Beams Simple Beams Beams Fixed on One End, Supported at Other Beams Fixed at Both Ends D-0

111 Metal Framing Engineering Data Design pplications (continued) Load tables on page D-50 D-56 for, B, C, E and H series channel are for single span beams supported at the ends. These can be used in the majority of cases. There are times when it is necessary to know what happens with other loading and support conditions. Some common arrangements are shown in Table 6. Simply multiply the loads from the Design Load Tables times the factors given in Table 6. Examples shown on page D-2. Table 6 Conversion Factors for Beams with Various Static Loading Conditions LOD DEFLECTION LOD ND SUPPORT CONDITION FCTOR FCTOR. Simple Beam Uniform Load Simple Beam Concentrated Load at Center Simple Beam Two Equal Concentrated Loads at 4 Points Beam Fixed at Both Ends Uniform Load Beam Fixed at Both Ends Concentrated Load at Center 6. Cantilever Beam Uniform Load Cantilever Beam Concentrated Load at End Continuous Beam Two Equal Spans.0.92 Uniform Load on One Span Span Span 9. Continuous Beam Two Equal Spans Continuous Beam Two Equal Spans.62. Concentrated Load at Center of One Span. Continuous Beam Two Equal Spans.6.48 Concentrated Load at Center of Both Spans D-

112 Metal Framing Engineering Data Design pplications (continued) 5" 0" 5" 0" " 0" EXMPLE I PROBLEM: Determine the load and deflection of an -200 beam continuous over one support and loaded uniformly on one span. SOLUTION:. From load table for -200 the load for a 5'0" span is 06 lbs. and deflection is.58". B. Multiply by factors from Table 6. Load = 06 lbs. x.0 = 9.8 lbs. Deflection =.58 x.92 =.29" EXMPLE II PROBLEM: Determine load and deflection of an E-200 cantilever beam with a concentrated load on the end. SOLUTION:. From load table for E-200 the load for a '0" span is 226 lbs. and deflection is.088". B. Multiply by factors from Table 6. Load = 226 lbs. x.2 = lbs. Deflection =.088 x.20 =.282" Column Height K Value Illustration COLUMN LODING The load bearing capacity of column or compression members is a function of the inherent configurational strength, the unbraced length and design of the end connections. Values of axial column loading given in Table were calculated using a rotationally free and translation fixed correction at each end (see illustration I). This gives an end condition constant (K) of. If other end conditions are used, axial loading should be calculated using procedures in the ISI specification for the design of cold formed steel structural members (SG6) and the engineering values for Superstrut channel given in Table. End Condition Code Rotation fixed and translation fixed Rotation free and translation fixed Rotation fixed and translation free D-2

113 Metal Framing Engineering Data Design pplications (continued) Table Load Carrying Capacities of Hot-Rolled Steel Rod Table 8 Rod Size Determined by Pipe Size for Fire Protection Safety factor of 5. Table 9 Maximum Spacing between Pipe Supports Steel Pipe Nom. Pipe Size (IN.) Max. Spacing (FT.) Copper Size DIMENSIONS (IN.) LODS NOMINL ROOT RE ROD DI. THRED Nom. Pipe Size (IN.) Max. Spacing (FT.) Safety factor of 5. Table 0 Minimum Spacing (IN.) between Centers of Standard Pipe When Using Superstrut #02 Pipe Straps DIMENSIONS (IN.) LODS NOMINL ROOT RE ROD DI. THRED 4 to to to to 2 8 NOM. PIPE SIZE D-

114 Metal Framing Engineering Data Design pplications (continued) Table Standard Dimensions and Weights of Piping Materials and Conduit MECHNICL (SCHEDULE 40) NOMINL STD. PIPE PIPE COUPLING SIZE O.D. O.D. (IN.) (IN.) (IN.) ELECTRICL CONDUIT NOMINL RIGID STEEL THIN WLL (EMT) CONDUIT CONDUIT CONDUIT SIZE O.D. O.D. (IN.) (IN.) (IN.) * Includes weight of heaviest conductor combination D-4

115 Metal Framing Engineering Data Design pplications (continued) Table 2 Extra Strong Pipe (Schedule 80).S.. B6.0 SCHEDULE NOMINL NOS. ND NOMINL PIPE OUTSIDE WLL INSIDE WLL THICKNESS SIZE DIMETER THICKNESS DIMETER DESIGNTIONS (IN.) (IN.) (IN.) (IN.) EXTR STRONG PIPE and SCHEDULE 80 PIPE (through 8") OD EXTR STRONG PIPE 6 OD (0" through 24" OD) 8 OD OD OD SCHEDULE 80 PIPE 4 OD (0" through 24" OD) 6 OD OD OD OD Table Pipe Covering Weights Thickness (Intended as Guide Only) and Weight of Calcium Silicate Covering NOMINL PIPE THICK. THICK. THICK. THICK. THICK. THICK. THICK. SIZE (IN.) (IN.) (IN.) (IN.) (IN.) (IN.) (IN.) D-5

116 Metal Framing Engineering Data Design pplications (continued) Column height, equal shelf spacing Table 4 Column Loading for Rack Construction General Storage Racks Pallet Racks Barrel Racks Bulk Furniture Racks Cable Racks Bar Stock Racks Display Racks Special Purpose Racks For Uniform Loads on Horizontal Members, See Table Typical general storage rack for use with plywood or other decking LLOWBLE LOD IN LBS. PER UPRIGHT COLUMN NUMBER OF SHELVES PER UPRIGHT HEIGHT CT. NO ' ,2,925,650,4, ,0,580,00 2,0 2,450 B B-402,90,00,500,00,90 ' ,50,850,60,425,280, ,000,525,000 2,00 2,40 2,200 B B-402,800,650,450,00, ' ,000,820,600,400,250,50, ,900,45,000 2,00 2,400 2,85 2,000 B B-402,650,60,450,00, ' -200,950,80,55,400,250,0, ,800,400,020 2,65 2,400 2,80,95,800 B B-402,500,500,40,25,60, ' -200,80,00,500,00,200,00, ,600,00,000 2,650 2,50 2,000,95,800,650 B B-402,450,480,400,250,40, D-6

117 Metal Framing Engineering Data Federal Specifications (WW-H-)/ Manufacturers Society Specifications (MSS SP69) C-0 dj. Steel Clevis Sizes 4" through 20" IPS Federal Type SP69 Type C-2 / CT-2 dj. Swivel Ring Hanger Sizes 2" through 8" IPS 2" through 4" tube Federal Type 0 SP69 Type 0 "B" Max. Dia. Rod Size M- MI Socket only for S Split Ring Hanger Sizes 8" through 8" Rod Federal Type 6 SP69 Type 6 C-26 Steel Double Bolt Pipe Clamp Sizes 2" through 24" IPS Federal Type SP69 Type M-8 / MT-8 MI Split Pipe Ring w/wo turnbuckle adj. Sizes 2" through 8" IPS 2" through 4" tube Federal Type SP69 Type 2 E-20- Forged Steel Weldless Eye Nut Sizes 8" through 2" rod Federal Type SP69 Type C-25 Steel Pipe Clamp Sizes 2" through 24" IPS Federal Type 4 SP69 Type 4 CL-0 Light-Duty Clevis Hanger Sizes 2" through 4" Federal Type Steel Concrete Insert Federal Type 9 SP69 Type 8 CF-0 dj. Steel Band Hanger Sizes 2" through 8" IPS 4" through 4" tube Federal Type F-2 Forged Steel Turnbuckle Sizes 8" through 2" rod Federal Type SP69 Type C-55 T / C-5 T Center I-Beam Clamp Federal Type 2 SP69 Type 2 C-20 / CT-20 Extension Pipe or Riser Clamp Sizes 4" through 20" IPS 2" through 6" tube Federal Type 8 SP69 Type 8 F- Forged Steel Clevis Sizes 8" through 2" rod Federal Type 4 SP69 Type C-80 Welded attachment as shown or inverted less bolt Federal Type 22 SP69 Type 22 M-5-L / C-5-L MI or Steel C-Clamp Sizes 8" through 8" Federal Type 2 SP69 Type 2 H-5 U-Bolt Sizes 2" through 24" IPS Federal Type 24 SP69 Type 24 M-8 Top Beam C-Clamp Sizes 8" through 4" rod SP69 Type 9 M- Junior Top Beam C-Clamp Sizes 8" through 2" rod SP69 Type 8 C- J Pipe Hanger Sizes 2" through 8" pipe SP69 Type 5 D-

118 Metal Framing Engineering Data Federal Specifications (WW-H-)/ Manufacturers Society Specifications (MSS SP69) C-04- Offset J-Hook Sizes 2" through " IPS Federal Type 2 C-9-H Heavy Welded Steel Bracket Max. Load,000 lbs. Federal Type 4 SP69 Type M-2-H I-Beam w/eye Nut Federal w/o links Type 28 Federal w/links Type 29 SP69 Type 28 M-50 Side Beam Bracket Sizes 8" through 8" Rod Federal Type 5 SP69 Type 4 M-2 / M-2 Ext I-Beam Clamp w/swing Nut Sizes 8" through 8" Rod Federal Type 0 SP69 Type 0 C-85- Pipe Stanchion Saddle Sizes 4" through 6" IPS Federal Type 8 SP69 Type C-6 Light Welded Steel Bracket Federal Type 2 SP69 Type C-86 dj. Pipe Saddle Support Sizes 2 2" through 6" IPS Federal Type 9 SP69 Type 8 C-89 Steel Pipe Covering Protection Saddle Sizes up to and including 0" IPS Federal Type 40 SP69 Type 9 C-89-L Steel Pipe Covering Protection Saddle Sizes 2" IPS and larger Federal Type 40B SP69 Type 9 C-90 Insulation Protection Shield for Vapor sealed pipe lines and insulated copper tubing Sizes 4" through 2" IPS Federal Type 4 SP69 Type 40 RC-29 Single Pipe Roll Sizes " through 24" IPS Federal Type 42 SP69 Type 4 C-29 dj. Roller Hanger Sizes " through 20" IPS Federal Type 44 SP69 Type 4 S-0-C Pipe Roll Complete Federal Type 45 SP69 Type 44 S-0-D dj. Pipe Roll & Base Federal Type 4 SP69 Type 46 D-8