REDI-RAIL - Accessories

Size: px

Start display at page:

Download "REDI-RAIL - Accessories"

Judith Janice Allen
6 years ago
Views:

1 Standard Splice Plates One pair including hardware provided with each straight section. Offset Reducing Splice Plates FLEX-MOUNT djustable Splice Plates 1 /4" hardware. Horizontally adjustable to 90. Vertically adjustable to 15. For optional rung, see page RER-12. Requires supports within 24 on both sides, per NEM VE 2. Right (or Left) Reducer R4-SSP R4-FSP R5-SSP R5-FSP Step Down Splice Plates Furnished in pairs with 1 /4" hardware. R6-SSP R7-SSP Center Reducer R6-FSP R7-FSP To Box Splice Plates R4-RSP- r R5-RSP- r to to to to to to R-DSP-45 R-DSP-46 R-DSP-47 R-DSP-56 R-DSP-57 R-DSP-67 Specify the following: C = center reducer S = side reducer R6-RSP- r R7-RSP- r r (tray reduction) 3, 6, 9, 12, 15, 18, 21, 24, 27, or 30 R4-TTB R5-TTB R6-TTB R7-TTB Vertical djustable Splice Plates Expansion Splice Plates daptor Splice Plates Bonding jumper required. For connecting to old Redi-Rail system. Requires supports within 24 on both sides, per NEM VE 2. R4-VSP R5-VSP R6-VSP R7-VSP R4-ESP R5-ESP R6-ESP R7-ESP R4-SP R5-SP R6-SP R7-SP RER-5 Cable Systems

Loading is 1,000 lbs. (4.45kN) per pair with safety factor of 3. Position TR 3 (76mm) wider than cable tray.

2 Bonding Jumper Furnished with 1 /4" hardware. Conduit to daptors Conduit to daptors Mounting hardware not included. Conduit Size in mm Conduit Size 1 /2, 3 /4 15, 20 9G /2, 3 /4 1 /2 BL1400 mpacity Hanger Rod Bracket Furnished as pair of studded clamps with 1 /4 serrated flanged lock nuts. Loading is 1,000 lbs. (4.45kN) per pair with safety factor of 3. Position TR 3 (76mm) wider than cable tray. 1, 1 1 /4 25, 32 9G , 1 1 /4 1 1 /2, 2 40, 50 9G /2, /2, 3 65, 80 9G /2, /2, 4 90, 100 9G /2, 4 Drop-Out Provides 4 (101mm) radius. Holes provided to secure cables. 3 /4 BL BL /2 BL1430 Redi-Rail Clamp/Guide Features a no-twist design. Has four times the strength of the traditional design. Each side is labeled to ensure proper installation. Designed for 1 /4 hardware. or without hardware. Patent No. RE (38mm) Support TR Size 3 /8 9(*)-R238 1 /2 9(*)-R250 R-OUT- 9ZN-1204 (without hardware) (*) Insert ZN or SS = tray width 9ZN-1204NB (with hardware) Frame Type Box Connector Furnished with 1 /4" hardware for tray connection. Blind End Furnished as one plate with 1 /4" hardware. R4-FTB- R4-END- R5-FTB- R5-END- R6-FTB- R6-END- R7-FTB- = tray width R7-END- = tray width Cable Systems RER-6

3 Trapeze Support Kit B-Line trapeze kits provide the components required for a single trapeze support in one package. These kits are available in pregalvanized steel with zinc-plated hardware or hot dip galvanized steel with 316 stainless steel hardware. The SH channel provides the convenience of pre-punched slots, which eliminate the need for field drilling. The illustrated hardware is sealed in a plastic bag and boxed with the channel, which is pre-cut to the appropriate length as shown in the chart. (2) 1/2" x 7/8" Hex Head Cap Screw (2) 9ZN-1205 Hold-Down Guide Clamp (2) N525WO Channel Nut (4) 1/2" Hex Nut (4) B202 Square Washer (1) B22 Channel cut to the required length Catalog Channel Uniform No. Width Length Load in. mm in. mm lbs kn 9P SH( ) P SH( ) P SH( ) P SH( ) P SH( ) P SH( ) P SH( ) P SH( ) Designed for use with 1 /2" threaded rod. Order rod separately. Heavy Duty Trapeze Support Kit B-Line trapeze kits provide the components required for a single trapeze support in one package. These kits are available in Dura-Green epoxy coated steel with zinc-plated hardware or hot dip galvanized steel with 316 stainless steel hardware. The SH channel provides the convenience of pre-punched slots, which eliminates the need for field drilling. The illustrated hardware is sealed in a plastic bag and boxed with the channel, which is pre-cut to the appropriate length as shown in the chart. Designed for use with 1 /2" threaded rod. Order rod separately. (2) 1/2" x 7/8" Hex Head Cap Screw (2) 9ZN-1205 Hold-Down Guide Clamp (2) N525WO Channel Nut (4) 1/2" Hex Nut (4) B202 Square Washer (1) Channel cut to the required length ( ) Insert 3 /8 for 3 /8" threaded rod hardware. Safety factor of 3.0 on all loads. Catalog Channel Uniform No. Width Length Load in. mm in. mm lbs kn 9(*) SH (*) SH (*) SH (*) SH (*) SH (*) SH (*) SH (*) SH (*) Insert GRN or G Safety factor of 3.0 on all loads. Trapeze Hardware Kit 9ZN /2 9G /2 In plastic bag 1 pr. 9ZN pr. 9G HHC Screw 1 /2 x 7 /8 ZN 2 HHC Screw 1 /2 x 7 /8 SS6 2 N525 WO ZN 2 N525 WO SS6 4 B202 ZN 1 /2" sq washer 4 B202 HDG 1 /2" sq washer 4 HN 1 /2 ZN 4 HN 1 /2 SS6 Rooftop Support Bases with B22 Channel Height x Width x Length Designed as a superior rooftop support for cable tray, UV resistant and approved for most roofing material or other flat surfaces. Can be used with any of B-Line cable tray clamps and guides. Ultimate Load Capacity: 1,000 lbs. (uniform load) DB /8 x 6 x 28.0 DB /8 x 6 x 36.0 DB /8 x 6 x 42.0 DB /8 x 6 x 50.0 DB /8 x 6 x 60.0 LEEDS credit available, base made from 100% recycled material. General Note: Consult roofing manufacturer or engineer for roof load capacity. The weakest point may be the insulation board beneath the rubber membrane. RER-7 Cable Systems

4 Center Hung Support Center Hung Cable Support allows cable to be laid-in from both sides. Eliminates costly cable pulling and field cutting of cable tray supports. Labor costs are dramatically reduced. Required hardware and threaded rod material for trapeze assemblies are reduced by 50%. Designed for use with 1 /2" threaded rod. (Order rod separately) Use with all aluminum and steel cable trays through 24" width. Load capacity is 700 lbs. per support. Safety factor of 3.0. Eccentric loading is not to exceed a 60% vs. 40% load differential. The maximum recommended unsupported span length is 144"/12 ft. (3.66 m). Hardware shown is furnished. (2) 1/2" Hex Nut (1) B202 Square Washer (2) 1/2" x 7/8" Hex Head Cap Screws (1) 9/16" Inside diameter steel tubing welded to strut (2) 9ZN-1205 Hold Down Guide Clamp (2) N525WO (1) B22 Channel cut to the required length Catalog Channel No. Width Length 9ZN ", 9", 12" 18" 9ZN ", 24" 30" ZN = Zinc Plated Center Hung Support Hardware Kit In plastic bag 9ZN pr. 9ZN HHC Screw 1 /2 x 7 /8 ZN 2 N525 WO ZN 1 B202 ZN 1 /2" sq washer 2 HN 1 /2 ZN Bracket Bracket Finishes available: ZN GRN or HDG Uniform Load Width '' B & & B B Finishes available: ZN GRN or HDG Uniform Load Width '' B B B B Cable Systems RER-8

5 Cantilever Bracket Cantilever Bracket Finishes available: ZN GRN HDG or SS4 Finishes available: ZN GRN HDG SS4 or SS6 Uniform Load Width '' B & & B B Uniform Load Width '' B & & B B B B B Underfloor Support (U-Bolts not included) Finish available: ZN U-Bolt Size Fits Pipe O.D. B501-3 / B B / B / B B / Order properly sized U-Bolts separately. Uniform Load Width '' B409UF & & B409UF & & Heavy Duty Hold Down Bracket Design load is 2000 lbs/pair. Two bolt design. Sold in pairs. 3 /8" cable tray attachment hardware provided. 1 /2" support attachment hardware not provided. (*) Insert ZN SS4 or SS6 Heavy Duty Hold-Down Bracket Design load is 4000 lbs/pair. Four bolt design. Sold in pairs. 3 /8" cable tray attachment hardware provided 1 /2" support attachment hardware not provided. (*) Insert ZN SS4 or SS6 9(*) (*)-1242 RER-9 Cable Systems

Mounting Bracket Furnished with 1 /4" hardware. #12-24 U-Nuts sold separately. ttaches to in over 20 positions. EI/TI panel mounting holes - both sides. Mounting holes for NEM outlet/junction boxes.

6 Mounting Bracket Furnished with 1 /4" hardware. #12-24 U-Nuts sold separately. ttaches to in over 20 positions. EI/TI panel mounting holes - both sides. Mounting holes for NEM outlet/junction boxes. Zinc plated steel. Includes mounting screws. Inside flange application bracket must match side rail height. See page RER-16 for Voice/Data/ Video and Power Options " 9ZN-MB1-4 mounting bracket shown. Inside Side Rail Flange pplication 9ZN-MB1-4 mounting bracket shown with 4" electrical box. Outside Side Rail Flange pplication Inside Outside Flange Flange pplication pplication in (mm) 9ZN-MB1-4 4" for RSI04 4" or 5" as desired 3 5 /8 92 9ZN-MB1-5 5" for RSI05 4" or 5" as desired 4 5 / ZN-MB1-4 mounting bracket shown with patch panels. Low Voltage dapter Mounting for low voltage wall plates. Snaps into mounting bracket 9ZN-MB1-4 or 9ZN-MB1-5. Zinc plated steel. #6-32 U-nuts included. See page RER-16 for Voice/Data/ Video and Power Options " " 2.938" 9ZN-LV1-1 (cutout on front) 9ZN-LV1-1 (cutout on bottom) 3.500" 3.28" Ref 3.500" 9ZN-LV " 9ZN-LV1-1 shown 9ZN-LV1-1 Under Rung Fastener ttachment Supports electrical fixtures from bottom of rung or siderails. Wing nut included. Various 1 /4"-20 stud lengths available. Static Load Capacity: 75 Lbs. (34kg). BX-4-16 BX BX BX Stud Length 5 /8 (16mm) 1 1 /2 (38mm) 2 (51mm) 3 (76mm) Cable Systems RER-10

REDI-RAIL - Accessories

REDI-RAIL - Accessories - ccessories Standard Splice Plate One pair including hardware provided with each straight section. (Expansion splice quantity subtracted) R4-SSP R5-SSP R6-SSP R7-SSP Expansion Splice Plate Bonding jumpers