ELECTRICAL ACCESSORIES FOR 1 5 8" (41 MM) WIDTH SERIES CHANNEL
|
|
- Clementine Walters
- 5 years ago
- Views:
Transcription
1 ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL Page Electrical Fittings Receptacles Fixture Hangers ccessories and Connectors Junction Boxes In-Channel Joiners Swivel Hangers Cable Entrance Tubing and ccessories MTERIL Unistrut fittings, unless noted, are made from hot-rolled, pickled and oiled steel plates, strip or coil, and conform to STM specifications 55, 56, 635, or 36. The fitting steel also meets the physical requirements of STM 50 GR 33. The pickling of the steel produces a smooth surface free from scale. Maple cable saddles, cable clamps and bus bar clamps are made from kiln-dry maple treated with paraffin to a depth of 6" (.6mm). Special sizes of clamps can be fabricated upon request. Porcelain cable clamps are made by the dry process and white glazed. Cable saddles are fiberglass-reinforced polyester. FINISHES Components listed in this section are available in: electro-galvanized (EG), conforming to STM B633 Type III SC; Hot-dipped galvanized (HG), conforming to STM 23 or 53, Perma-Green II (GR), and plain (PL). Note: Many Unistrut Metal Framing components, when used with appropriate closures, are UL listed, and CS approved. DESIGN LOD Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 2.5, unless otherwise noted. DIMENSIONS Imperial dimensions are illustrated in inches. Metric dimensions are shown in parenthesis or as noted. Unless noted, all metric dimensions are in millimeters and rounded to one decimal place. 48
2 UNISTRUT RCEWY FILL CHRTS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL U.L. LISTED Unistrut channel is listed by Underwriters' Laboratories as a surface metal raceway. Snap-in closure strip is used to complete the raceway. ccessory parts listed by Underwriters are noted on drawings. The following tables represent maximum number of conductors when raceway is not employed with fixtures or where the clearance between fixtures and raceway is greater than 2" (2.). In all cases the snap-in cover is required to complete raceway enclosure. P3000, & -KO Number and Conductor Size (WG) Gage THWN, THHN XHHW T, TW THW RH RHH, RHW P3300, P4000 Number and Conductor Size (WG) Gage THWN, THHN XHHW T, TW THW RH RHH, RHW P5500, & -KO Number and Conductor Size (WG) Gage THWN, THHN XHHW T, TW THW RH RHH, RHW P000, & -KO, P00 & -KO, P2000 & -KO Number and Conductor Size (WG) Gage THWN, THHN XHHW T, TW THW RH RHH, RHW P5000, & -KO Number and Conductor Size (WG) Gage THWN, THHN XHHW T, TW THW RH RHH, RHW C.S.. PPROVED MXIMUM NUMBER OF WIRES FOR TYPES T, THHN, THW, THWN, TW, R, RH, RHH, RHW OR XHHW Suitable for number of wires in Column when installed to support and supply electric discharge type lighting fixtures when raceway wiring is suitable for at least 5 C except wire suitable for 60 C may be used when clearance between fixtures and raceways is at least 2" (2.). lso suitable for number of wires in column B when installed to support electric discharge type lighting fixtures when raceway wiring is suitable for at least 5 C and clearance between fixtures and raceway is at least 8" (3.2). Raceway Wire Size WG P000, &-KO P00, &-KO P2000. &-KO B B B B B Unistrut channels are also certified by Canadian Standards ssociation. P3000, &-KO P3300, P4000 P5000 &-KO P5500, &-KO 49
3 ELECTRICL FITTINGS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P53 FG P54 FG 2" (50.8) CBLE SDDLES Maximum "" Cable Diameter Weight/C In mm In mm Lbs kg Material: FG - Fiberglass Reinforced Polyester, PO - Dry Process White Glazed Porcelain P53 FG P54 FG P53 PO P54 PO P2649 thru P2649 H Hole Size 5 8" (4.3) B MPLE CBLE SDDLES 3 8" Flat Head Machine Screw included. Specify hole size when ordering. Order channel nuts as required. Material: Maple hardwood paraffin impregnated. Hole Size "" "B" Weight/C In mm In mm In mm Lbs kg P P2649 B P2649 C P2649 D P2649 E P2649 F P2649 G P2649 H over 4 over 0.6 P2645 thru P2645 H 5 8" (4.3) MPLE CBLE CLMPS Hole Size B 3 8" studs, square nuts and washers included. Specify hole size when ordering. Order channel nuts as required. Material: Maple hardwood paraffin impregnated. Hole Size "" and "B" Dimensions Weight/C In mm In mm Lbs kg P P2645 B P2645 C P2645 D P2645 E P2645 F P2645 G P2645 H over 4 over
4 ELECTRICL FITTINGS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P264 thru P264 F 4" (0.6) BUS BR MPLE CLMPS B 5 8" (4.3) 2 " studs, square nuts and washers are included. Channel nuts must be ordered separately. Bus bar maple clamps also available in 4" (6.4) x 2" (50.8) and 4" (6.4) x 6" (52.4) 4" (0.6) 3 8" (8.3) 4" (5.4) Maple Separator Material: Paraffin impregnated maple hardwood. "" "B" No. Bus Wt/C Separators Per Leg Lbs No. Bars In mm In mm kg P P264 B P264 C P264 D P264 E P264 F P690 thru P69 MPLE CBLE CLMPS Hole Size Use with steel clamp and Everdur hardware. Order clamp separately. Specify hole size when ordering. Material: Paraffin impregnated maple hardwood. Order Steel Clamp Number Hole Size "" Wt/C In mm In mm Lbs kg P690 P3 E P69 P5 E P692 P E P693 P8 E P694 P9 E P695 P20 E P696 P2 E P69 P23 E
5 ELECTRICL FITTINGS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P8 thru P95 B PORCELIN CBLE CLMPS Hole Size Use with steel clamp and Everdur hardware. Order clamp separately. Material: Dry process porcelain white glaze. Order Steel Clamp Number Hole Size "" Weight/C In mm In mm Lbs kg P P8 B P3 E P8 C P P P88 B P5 E P88 C P P P89 B P E P89 C P P P90 B P9 E P90 C P P P9 B P20 E P9 C P P P92 B P2 E P92 C P P P93 B P23 E P93 C P P P94 B P24 E P94 C P P95 P24 E P95 B
6 RECEPTCLES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P255 DUPLEX GROUNDED RECEPTCLE P2553 Wire Connectors 25 V, 5 amp receptacle, NEM configuration S-5R, cover plate. #6 screws, nuts and wire connectors included. Leads are 4 gage 05 C plastic covered. Ground wire is green 6 gage. 6" (52.4) Oval Head #6-32 X " P Finish: White powder coat. P384 Closure Wt/C 38 Lbs (.2 kg) P26 P262 RECEPTCLE BOX 4" x 5 8" P263 P264 P265 RECEPTCLE UNIT 8" Knockout 8" Knockout 4" x 5 8" Includes Nuts and Screws Includes Nuts and Screws P P Outlet Weight/C Lbs kg P26 Single P262 Duplex Outlet Lbs Weight/C P263 25V R P V R P265 2V R kg NEM Receptacle Configuration 53
7 FLUORESCENT FIXTURE HNGERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P253 P553 FLOURESCENT FIXTURE HNGERS 4" X " RHMS and Sq. Nut Included P2539 P3539 P5539 FLOURESCENT FIXTURE HNGERS 4" X " RHMS and Sq. Nut Included Hanger provides more than 2 " (2.) space between channel and fixtures. Materials: 8 gage (.2). 9 32" (.) Dia. Hole 5 8" (4.3) Design Load 20 Lbs (.5 kn) Hanger provides 8" (3.2) space between channel and fixtures. Materials: 8 gage (.2). 5 8" (4.3) 4" X 3 4" Carriage Bolt and Sq. Nut Included Design Load 20 Lbs (.5 kn) Part Number Use With Channel "" Weight/C In mm Lbs kg P000 P253 P P2000 P3000 P553 P Part Number Use With Channel "" Weight/C In mm Lbs kg P000 P2539 P P2000 P3539 P P5539 P P255 P256 P25 RCEWY HNGERS P2855 P2856 P285 RCEWY HNGERS 4 4" (08.0) 2 3 4" (69.9) 9 32" (.) Sq. Hole 9 32" (.) Sq. Hole Use with Channels: P00, P0, P200, P5000, & P5500. Design Load 20 Lbs (.5 kn) Use with Channels: P000, P00, P2000, P3000, P3300, P4000, P400, P400, & P40. Design Load 20 Lbs (.5 kn) Material: 4 gage (.9). Material: 4 gage (.9). "" Weight/C In mm Lbs kg P P P "" Weight/C In mm Lbs kg P P P
8 ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P3922 thru P3926 Back Clevis SPLICE FITTINGS P (.9) Gage Threaded Plate Nut 6 3 4" (.5) 4" X 5 8" Flat Head Machine Screws and 4 Hole Splice Plate Nut Included Use Back Plate ssembly "" Clevis With Weight/C Clevis Nut Number Number Channel In mm Number Number Lbs kg P000 P3922 P P23 P25 P P2000 P3923 P P33 P25 P P3924 P P53 P25 P P3925 P P23 P55 P Material: 6 gage (.6). P3926 P P23 P50 P P P CONDUIT SWING FITTING 2" (50.8) P For 2" Rigid Conduit P For 3 4" Rigid Conduit 4" X 3 4" Slotted Hex Head Screws and Nuts Included 2 Holes 9 32" (.) 3 6" (4.8) 2" (50.8) Bushing Not Included 4 3 6" (22.2) 2" (50.8) Ground Wire 5 (.08π) 5 (.08π) Design Load 300 Lbs (.3 kn) Conduit hanger fittings allow a free swivel of 5 in one direction. Fitting may be mounted to the slot side of the Unistrut channel or to the back. Wt/C 96 Lbs (43.5 kg) 55
9 ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P2535 8" (22.2) Dia. CONDUIT HNGER CONNECTION FOR 2" CONDUIT 4" X 5 8" Flat Head Machine Screws and P Nuts Included P " (2.8) Dia. CONDUIT HNGER CONNECTION FOR 3 4" CONDUIT 4" X 5 8" Flat Head Machine Screws and P Nuts Included 4" (0.6) Design Load 400 Lbs (.8 kn) 5 8" (4.3) 5 8" (30.2) Design Load 200 Lbs (.9 kn) Material: 2 gage (2.). Wt/C 28 Lbs (2. kg) Material: 6 gage (.5) Wt/C 36 Lbs (6.3 kg) P2522 OUTLET BOX CONNECTION P " (49.2) 3 6" 3 6" (30.2) (30.2) 5 6" (49.2) 4" X 5 8" Flat Head Machine Screws and P Nuts Included P3000 4" X 5 8" Flat Head Machine Screw and P Nut Included 2 4" (5.2) END CONNECTORS FOR 2" CONDUIT 8" (22.2) Dia. 6 4" (58.8) 3 Knockouts 8" (22.2) Dia. Wt/C 35 Lbs (5.9 kg) Material: 2 gage (2.). Wt/C 2 Lbs (2.2 kg) P P " X 5 8" Flat Head Machine Screw and P Nut Included Material: 2 gage (2.) END CONNECTORS FOR 2" & 3 4" CONDUIT 2 6" (52.4) For Unistrut channels P000, P00, & P2000. P P " X 5 8" Flat Head Machine Screw and P Nut Included P5500 Material: 2 gage (2.). END CONNECTORS FOR 2" & 3 4" CONDUIT 3 8" (34.9) Conduit Size Weight/C In Lbs kg P P Conduit Size Weight/C In Lbs kg P P
10 ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P P502-5 END CONNECTOR FOR 2" & 3 4" CONDUIT P END CONNECTOR FOR " CONDUIT P5000 4" X 5 8" Flat Head Machine Screw and P Nut Included 5 8" (4.3) 4" X 5 8" Flat Head Machine Screw and P Nut Included P000 Tapped for " Conduit Thread 2 6" (52.4) Material: 2 gage (2.). Conduit Size Weight/C In Lbs kg P P Material: 2 gage (2.). Wt/C 24 Lbs (0.9 kg) P END CONNECTOR FOR " CONDUIT P END CONNECTOR FOR " CONDUIT Tapped for " Conduit Thread Tapped for " Conduit Thread P5000 P5500 4" X 5 8" Flat Head Machine Screw and P Nut Included 5 8" (4.3) 4" X 5 8" Flat Head Machine Screw and P Nut Included 5 8" (4.3) Material: 2 gage (2.). Material: 2 gage (2.). Wt/C 28 Lbs (2. kg) Wt/C 24 Lbs (0.9 kg) P80 W thru P5580 W WIREWY END CPS Material:.05" (.9) Use Weight/C With Lbs kg P80 W P P280 W P P2280 W P P3280 W P P4280 W P P5280 W P P5580 W P
11 ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P254 SPCER CLEVIS 8" DI. (22.2) 8" (3.2) UNISTRUT Channel P " (42.) 2" (50.8) 4" (0.6) 2" (50.8) Flourescent Fixture P2540 Wiring Stud Nut Material: 2 gage (2.). Wt/C 24 Lbs (0.9 kg) P2540 P2540 WIRING STUD NUT P36-25 FIXTURE STUD NUT 2" merican Standard Pipe Thread 4" x 20 Thd. 3 6" (30.2) Material: Sintered metal. Design Load 320 Lbs (.4 kn) "" Weight/C In mm Lbs kg P2552 P P Wt/C Lbs (5.0 kg) POLYPROPYLENE WIRE RETINER 2" (38.) 2" (38.) Retainer may be easily pushed into channel to support wires until closure strip is installed. Wt/C.30 Lbs (. kg) 58
12 JUNCTION BOXES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P280 JUNCTION BOX P28 JUNCTION BOX * See note below. Wt/C 35 Lbs (6.2 kg) * See note below. Wt/C 55 Lbs (0.3 kg) P282 JUNCTION BOX P283 JUNCTION BOX * See note below. Wt/C 55 Lbs (0.3 kg) * See note below. Wt/C 5 Lbs (9.4 kg) P284 JUNCTION BOX * ll Junction Boxes illustrated on this page are: UL listed, CS approved. Junction boxes are for P000, P00 or P2000 channels. ll channel entries in box are 8" (28.6) diameter finished holes with no bushing needed. ll knockouts are 8" (22.2) diameter. 4" x 5 8" flat head machine screws and P included. * See note below. Wt/C 95 Lbs (88.5 kg) 59
13 IN-CHNNEL JOINERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P2900 P290 P000 Jam screws included. P000 Jam screws included. Material: Cast aluminum. P2902 Wt/C 20 Lbs (9. kg) Material: Cast aluminum. P2903 Wt/C 35 Lbs (5.9 kg) Jam screws included. P000 Jam screws included. P000 Material: Cast aluminum. Wt/C 2 Lbs (2.2 kg) Material: Cast aluminum. Wt/C 45 Lbs (20.4 kg) 60
14 SWIVEL HNGERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL M203 M2050 SWIVEL HNGERS M23 M250 SWIVEL HNGERS 3 8" (9.5) DI. B 3 8" (9.5) DI. B " (24.5) Part "B" Weight/C Number "" In mm Lbs kg M " " M2050 2" " Part "B" Weight/C Number "" In mm Lbs kg M23 3 8" " M250 2" " M2250 SWIVEL HNGER M2350 SWIVEL HNGER 3 8" (9.5) DI. 3 4" (44.5) 3 8" (9.5) DI. 3 4" (44.5) 2" - 3 THD. " (24.5) 2" - 3 THD. Wt/C 8 Lbs (8.2 kg) Wt/C 20 Lbs (9. kg) 6
15 CBLE ENTRNCE TUBING P6F Slot Size 3 4" (9.) X 8" (22.2) 3 4" (44.5) 2 32" (5.6) 23 32" (43.) Slot Size 32" (3.5) X 8" (22.2) Slot spacing 4" (3.8) on center. 2 32" (5.6) P2H Slot Size 3 4" (9.) X 8" (22.2) 2 3 6" (55.6) 2 32" (5.6) " (54.8) Slot Size 32" (3.5) X 8" (22.2) Slot spacing 4" (3.8) on center. 2 32" (5.6) BEM LOD* LOD (Lbs) P6F P2H * Maximum allowable uniform load. SPN (In) Channel Weight llowable Moment Material Thickness Lbs/Ft kg/m In-Lb N m In mm 0' 20' PL GR HG PG SS L P6F P2H Standard Lengths Finishes Other Materials 62
16 CBLE ENTRNCE TUBING DESIGN LOD DT Beam Data Column Data Span Channel Max. llowable Uniform Load Deflection at Uniform Load Uniform Load at Deflection Span/240 Max. Column Load pplied at C.G.* Max. Design Load pplied at Column Face* In mm Lbs kn In mm Lbs kn Lbs kn Lbs kn P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H ** ** ** ** *K = 0.80 **KL r > 200 Notes:. bove loads include the weight of the member. This weight must be deducted to arrive at the net allowable load the beam will support. 2. Long span beams should be supported in such a manner as to prevent rotation and twist. 3. llowable uniformly distributed loads are listed for various simple spans, that is, a beam on two supports. If load is concentrated at the center of the span, multiply load from the table by 0.5 and corresponding deflection by 0.8. ELEMENTS OF SECTION Channel reas of xis - xis 2-2 Section I S r I S r In 2 cm 2 In 4 cm 4 In 3 cm 3 In cm In 4 cm 4 In 3 cm 3 In cm P6F P2H I - Moment of Inertia S - Section Modulus r - Radius of Gyration 63
17 CBLE ENTRNCE FITTINGS P2820 P2940 CHNNEL/TUBE CONNECTORS P2822 P2932 SPLICE FITTINGS 5 3 8" (36.5) 3 3 4" (95.3) 5 8" (4.3) Splice Fitting ssembly Secured to Flat Side with Hardware Provided Use Either Threaded Hole 9 6" (4.3) Dia. Holes 3" (6.2) 6" (.) Dia. Holes Splicing should occur within the top one quarter of column height. Use Weight/C With Lbs kg P2820 P6F P2940 P2H Use Weight/C With Lbs kg P2822 P6F P2932 P2H P RCK FITTING P282 LOCKING CLIP P4000 P282 Locking Clip 5" (2.0) Cable Hook supplied by others. Exclusive Cable Hook Locking Clip prevents Cable Hook removal. Wt/C 66 Lbs (29.9 kg) Wt/C 3 Lbs (.4 kg) 64
18 CBLE ENTRNCE BRCKETS P2920 thru P2924 CBLE BRCKETS 3 6" (4.8) x 3 4" (9.) Slots 2 3 4" (69.9) on Center 5 8" (4.3) B L Use with P6F or P2H. Material: 2 gage steel. "L" "" "B" Weight/C Uniform Design Load In mm In mm In mm Lbs kg Lbs kn P P P P P Safety factor of 3. P2928 P2929 P " (4.3) CBLE BRCKETS B L Use with P6F or P2H. Material: 2 gage steel. "L" "" "B" Weight/C Uniform Design Load In mm In mm In mm Lbs kg Lbs kn P P P Safety factor of 3. 65
Electrical Accessories
complete system of top quality, time saving products, designed for surface metal raceways, lighting and cable supports. Innovative designs offer many installation advantages. -Line s surface raceways are
More informationPIPE/CONDUIT CLAMPS, SUPPORTS AND HANGERS FOR 1 5 8" (41 MM) WIDTH SERIES CHANNEL
PIPE/CONDUIT CLMPS, SUPPORTS ND HNGERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL Page Pipe/Conduit Clamps Pipe Hangers Pipe Rollers Pipe Brackets Reference Tables 2 40 4 44 MTERIL Unistrut pipe supports, unless
More informationElectrical Applications. Metal Framing & Cable Tray Superstrut Metal Framing System. Column A. Design Data: Materials: Column B
Electrical Raceway Series 800 Surface Raceway and Lighting Systems Superstrut channel together with snap-in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories
More informationBeam Clamps. Materials & Finishes (Unless otherwise
Beam Clamps Our beam attachments and pipe supports offered in this section are designed to provide supports without drilling or welding. complete selection of beam clamps, pipe clamps, rollers, supports
More informationSeries 1 Steel - Straight Sections
Series 1 Steel - Straight Sections Series 1 Steel H-1 B-Line series Cable Tray Systems Series 1 Steel - ccessories & Fittings Series 1 Steel How The Service dvisor Works We know that your time is important!
More informationSeries 2, 3, 4, & 5 Steel - Accessories
- ccessories Splice Plates Standard 8-hole pattern for all steel splice plates. One pair including hardware provided with straight section. Boxed in pairs Expansion Splice Plates Expansion plates allow
More informationSeries 2, 3, 4, & 5 Aluminum - Accessories
The following is a list of accessories and fittings that can be provided with S8 tray. For more information on these items, contact our Engineering Department. Fittings Horizontal Bends 30 Bends with 24,
More informationCOMPANY PROFILE: Eastman Impex is a global company, established in year 1996 and it has been accredited with ISO 9001: 2008.
COMPNY PROFILE: Eastman Impex is a global company, established in year 996 and it has been accredited with ISO 900: 008. Since 996 group is growing with increasing trend every year and now it comprises
More informationSeries 2, 3, 4, & 5 Aluminum - Accessories
Wedge Lock Splice Plates Standard 4-hole pattern. Furnished in pairs, with hardware. One pair including hardware provided with each section. Boxed in pairs with hardware. For field installation drill 13
More informationSeries 1 Steel - Accessories
- ccessories Standard (L-Shaped) Splice Plates One pair including hardware provided with each section. Prepackaged in pairs in a plastic bag, with hardware. 4-hole pattern L-shaped splice plates. L-shaped
More informationSeries 1 Steel - Straight Sections
- Straight Sections H-1 -Line series able Systems - ccessories & Fittings How The Service dvisor Works We know that your time is important! That s why the color-coding system in this catalog is designed
More informationTo Convert From To Multiply By To Convert From To Multiply By
Reference Data Metric Conversion Chart Reference Data To Convert From To Multiply By To Convert From To Multiply By Angle Length degree radian (rad) 0.01745329 foot (ft) meter (m) 0.3048 radian (rad) degree
More informationSeries 2, 3, 4 Steel Cable Ladder Steel Cable Ladder, Series 2, 3, 4 & 5
Cable Ladder with Slotted Rung (shown with alternating slot orientation) Cable Ladder with Slotted Rung (shown with continuous slot down - also available with continuous slot up) HDS-1 Steel Cable Ladder,
More informationSeries 1 Steel - Straight Sections
LST-1 able Systems - Straight Sections How The Service dvisor Works -Line knows that your time is important! That s why the color-coding system in this catalog is designed to help you select products that
More informationSeries 2, 3, 4, & 5 Aluminum - Straight Sections
- Straight Sections I-1 B-Line series Cable Tray Systems - Accessories For Aluminum Fittings see fittings section pages L-1 thru L-17 How The Service Advisor Works We know that your time is important!
More informationChannel Cable Tray - Accessories & Fittings
hannel able Tray - Straight Sections E-1 -Line series able Tray Systems hannel able Tray - ccessories & Fittings How The Service dvisor Works We know that your time is important! That s why the color-coding
More informationBrackets. B (304.8) BRACKET Uniform Loading 900 Lbs. (4.00 kn) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 260 Lbs. (117.
B187 BRCKET Uniform Loading 1450 Lbs. (6.45 kn) Hole Spacing on Bracket Top 5 5 /1 (150.8) Center to Center t./c 193 Lbs. (87.5 kg) 2 1 / B188 BRCKET Uniform Loading 1080 Lbs. (4.80 kn) Hole Spacing on
More informationPipe/Conduit Clamps & Hangers
Our beam attachments and pipe supports offered in this section are designed to provide supports without drilling or welding. complete selection of beam clamps, pipe clamps, rollers, supports and accessories
More informationCTSCL-10. Steel Cable Ladder Cable Support Systems
TSL-10 Steel able Ladder able Support Systems Tray onstruction I-Beam Side Rails ooper B-Line s I-Beam siderails are an integral part of all 2, 3, 4, and 5 series ladder trays. The I-Beam is ideal for
More informationWe offer two fire retardant (FR) resins for strut systems: polyester and vinyl ester. Both resins are ideal for corrosive environments.
Materials We offer two fire retardant (FR) resins for strut systems: polyester and vinyl ester. Both resins are ideal for corrosive environments. While polyester is sufficient for most uses, vinyl ester
More informationMaximum Support for Your Projects
Maximum Support for Your Projects Broadest Range of Concrete Solutions Concrete inserts are an ideal solution for drop rod support of trapeze. With the widest range of styles and accessories in the industry,
More informationSERVICE ENTRANCE - UNDERGROUND Single & Three Phase 200, & 320/400 Amp
Printed from NIPSCO.com 04-01-17 PAGE 1 OF 6 USE: Arrangement of service equipment to supply electric energy to an underground, outdoor self contained meter installation. LATEST REVISION: PREVIOUS REVISION
More informationMiscellaneous Fittings
B214 R&L REEL RCK SUPPORT FOR (32) PIPE 200 Lbs. (90.7 kg) B514 R&L REEL RCK SUPPORT FOR 2 (50) PIPE 246 Lbs. (111.6 kg) 3 5 /8 (92.1) 3 5 /8 (92.1) B214R Right Hand B214L Left Hand B514R Right Hand B514L
More informationPRODUCT CATALOG. 2010, Halex/Scott Fetzer Company TABLE OF CONTENTS. LIQUID Liquid-Tight Conduit Fittings
Electrical Metallic Tubing Fittings MC & C Cable & Flexible Metallic Conduit Fittings Non-Metallic Sheathed Cable Fittings Liquid-Tight Conduit Fittings Rigid & Intermediate Metallic Conduit Fittings Service
More information229 B-Line series Pipe Hangers & Supports
accessories offered in this section are designed to reduce installation time. wide range of types and sizes are available for various applications. Materials For maximum loading design, Carbon Steel, Forged
More informationSeries 3 & 4 Stainless Steel - Accessories
Splice Plates Standard 8-hole pattern for all stainless steel splice plates. One pair including hardware provided with straight section. Boxed in pairs with hardware. Expansion Splice Plates Expansion
More informationCLEVIS HANGER 401. Standard Duty B A
CLEVIS HNGER 40 Standard Duty Size Range: /2 through 24 Surface Finish: Electro-zinc plated non-insulated pipe lines Standard electro-zinc plated finish is cleaner, provides superior corrosion protection
More informationJACKSON ELECTRIC COOP METER LOOP CONSTRUCTION SPECIFICATIONS JUNE 2018
JACKSON ELECTRIC COOP METER LOOP CONSTRUCTION SPECIFICATIONS JUNE 2018 GANADO OFFICE PHYSICAL ADDRESS: 8925 State Highway 111 E Ganado, TX 77962 Phone: (361)771-4400 BAY CITY OFFICE PHYSICAL ADDRESS: 100
More informationCABLE MANAGEMENT SOLUTIONS CATALOGUE2003/04 A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS.
CABLE MANAGEMENT SOLUTIONS CATALOGUE03/04 A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS www.legrand.co.uk CHANNEL SUPPORT THE BACKBONE OF ALL YOUR SUPPORT NEEDS Swifts
More informationOperator Enclosures. Console Type 12 - AW-14 Data Sheet
Console Data Sheet Construction Console body, panel cover and door, top assembly and writing desk are fabricated from (14) gauge steel ll continuous welded seams are finished smooth Panel cover is secured
More informationUNEQUAL FLANGE RACK ACCESSORIES
CUSTOM CBINETS & RCKS Products for Custom Installation Solutions www.custcab.com UNEQUL FLNGE RCK CCESSORIES Custom Cabinets & Racks offers a large range of accessories to custom tailor UEF equipment racks
More informationSeries 3 & 4 Stainless Steel - Accessories
- Accessories Splice Plates Standard 8-hole pattern for all steel splice plates. One pair including hardware provided with straight section. (Expansion splice quantity subtracted) Boxed in pairs with hardware.
More informationUses, Certifications, and Standards STRUT FITTINGS,BF-FTGS,MISCELLANEOUS
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 B82352 Profile End Cap Cooper B-Line/Cable Tray Catalog Number Manufacturer Description Weight per unit Product Category
More informationCent-R-Rail Systems. WARNING: Do NOT use as a walkway, ladder or support for personnel. Cent-R-Rail. Cable Tray Systems
114 How The Service Advisor Works Cooper B-Line knows that your time is important! That s why the color-coding system in this catalog is designed to help you select products that fit your service needs.
More informationWire Mesh Safety Grips
Straight Male 90 Male Straight Female L7901 L7915 L7951 Liquid-Tight Grips U* R* Liquid-Tight Grips are woven stainless steel mesh with an anodized aluminum body for corrosion-resistance. They are used
More informationSuperstrut. Metal Framing. Threaded Products and Hardware. Channel Nuts. Design Data. Screw Threads. Finish and special materials
Channel Nuts Superstrut channel nuts are manufactured from Grade 2 mild steel and are case hardened. Design Data Superstrut self aligning channel nuts are designed to provide resistance to pullout and
More informationTC/American Product Catalog
CONTENTS Table of Contents -5 Rail Index B-1 Suspension Index C-1 Switches and Curves Index D-1 Trolleys Index E-1 Cranes Index F-1 End Trucks Index G-1 Drivetractors and Motorized Trolleys Index H-1 Electrification
More informationAnvil-Strut Price Sheet AS-3.11C Effective: March 28, 2011 Cancels Price Sheet AS.06.10C of June 28, 2010
nvil-strut Price Sheet S-3.11C Effective: March 28, 2011 Cancels Price Sheet S.06.10C of June 28, 2010 FOR THE MOST CURRENT PRODUCT/PRICING INFORMTION ON NVIL PRODUCTS, PLESE VISIT OUR WEBSITE T WWW.NVILINTL.COM
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationWire Mesh Safety Grips
Pulling Grips PS Series S PS Series grips feature a double weave of galvanized steel strands for greater strength and added mesh contact with the cable. Leviton Double Weave Pulling Grips are designed
More informationCABLE TRAY SURFACE RACEWAY J-HOOKS IN-FLOOR SYSTEMS POWER POLES DESK PEDESTALS CHANNEL TRAY
LE TY SUFE EWY J-HOOKS IN-FLOO SYSTEMS POWE POLES DESK PEDESTLS HNNEL TY hannel Tray from MonoSystems MTEIL LENGTH ft. m () HNNEL () HNNEL () HNNEL For 5-years MonoSystems has been creating innovative
More informationPipe Hangers. 47 B-Line series Pipe Hangers & Supports
Pipe hangers offered in this section are designed to support insulated or non-insulated pipe allowing for vertical adjustment and limited movement in the piping system. Materials arbon Steel, Malleable
More informationCATALOG. Superstrut metal framing system Metal framing channel and accessories
CTLOG Superstrut metal framing system Metal framing channel and accessories S U P E R S T R U T M E T L F R M I N G S Y S T E M M E T L F R M I N G C H N N E L & C C E S S O R I E S Thomas & etts is now
More informationT&B Cable Tray. Nonmetallic Strut Systems NM -SS P- 100 ( ) ( ) Channels
Channels Thomas & Betts is proud to present its new line of nonmetallic struts and accessoires. You ll find a complete selection of nonmetallic accessoires, fasteners, hangers, pipe clamps and channels.
More informationREDI-RAIL - Accessories
- ccessories Standard Splice Plate One pair including hardware provided with each straight section. (Expansion splice quantity subtracted) R4-SSP R5-SSP R6-SSP R7-SSP Expansion Splice Plate Bonding jumpers
More informationRigid Metal Conduit, IMC or EMT K-Clamps
65178 Rigid Metal Conduit, IMC or EMT K-Clamps Wt. Lbs. Std. Catalog No. Size (In.) Per 100 Pkg. Right Angle Type Right Angle Type Hot Dip/Mechanically Galvanized* For Rigid, IMC, EMT PC-50RA 1/2 37.0
More informationPipe Hangers. Pipe Hangers. Pipe Hangers & Supports
Pipe hangers offered in this section are designed to support insulated or non-insulated pipe allowing for vertical adjustment and limited movement in the piping system. Materials arbon Steel, Malleable
More informationThe Reliable Choice. Field Pocket Guide
The Reliable Choice Field Pocket Guide Allowable Ampacities of STABILOY Brand XHHW-2 and Copper 75 C (167 F) 90 C (194 F) 75 C (167 F) 90 C (194 F) Conductor Size (AWG or kcmil) Types RHW, THHW, THW, THWN,
More informationgrounded in service wired to innovate STABILOY Type XHHW-2 and USE-2/RHH/RHW-2
grounded in service wired to innovate STABILOY Type XHHW-2 and USE-2/RHH/RHW-2 grounded in service wired to innovate www.cable.alcan.com Type XHHW-2 and Type USE-2/RHH/RHW-2 Alcan manufactures XHHW-2 and
More informationForm 35 Malleable Iron Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC Conduit.
NEC/CEC Suitable for use in the following Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing. Connect and change direction of conduit runs. Allow connections
More informationCable Tray CT2D-18. Tray2Day SM. cable tray service program
Cable Tray CT2D-18 Tray2Day SM cable tray service program * * At, we believe that power is a fundamental part of just about everything people do. That s why we re dedicated to helping our customers s find
More informationIn This Section. Metal Framing, Pipe Hangers and Accessories. Superstrut Metal Framing, Pipe Hangers and Accessories D-1
In This Section Superstrut Metal Framing Channels Overview...D-2 D- Threaded Products and Hardware...D-8 D- Fittings and Brackets...D-4 D-2 Concrete Inserts...D-22 D-2 Beam Clamps...D-24 D-2 Pipe Straps,
More informationPART NUMBER POLE DIAMETER RANGE CARTON QTY " to 5" " to 6 3 4" " to 7 3 4" " to 8 3 4" 10
PH1 Offset Pole Band Bands Single Double Offset Pole Bands are used for dead-ending, guying, and mounting secondary racks on metal poles, pipe masts, or conduit. Each Pole Band Assembly contains two 1
More informationT&B Cable Tray. Nonmetallic Strut Systems NM -SS P- 100 ( ) ( ) Channels
Channels Thomas & Betts is proud of its line of nonmetallic strut and accessoires. You ll find a complete selection of nonmetallic accessoires, fasteners, hangers, pipe clamps and channels. Most Thomas
More informationElectrical Design/Build Guide
2017 Electrical Design/Build Guide Based on the 2017 National Electrical Code Copyright Durand & Associates 1986-2016 60 C Copper Ampacity 4 - Wire Fill - (Non-Current Carrying Neutral) 4 or 5 - Parallel
More informationPipe hanger solutions
Product catalog Middle East offering Pipe hanger solutions for commercial and industrial applications B00 series B00 - Standard clevis hanger Pipe will not pinch when installing. 5 swing in either direction
More informationCOMMERCIAL AND INDUSTRIAL FITTINGS: CONDUIT BODIES. Applications
Class I, Division per NEC 50.0(B)() Applications Larger body size facilitates pulling of large and heavy conductors. Specially designed raised cast covers provide additional wiring area. Mogul Unilets
More informationArmoured Cable/Flex. Conduit
Armoured Cable/Flex. Conduit Connectors Fittings & Accessories Grounding Trade Clamping Range Suggested Application Flex. Cat. No. Size min. max. AC90 (BX) Conduit CI70 CI71 / CI73 CI2210 / CI2236 L-16
More informationELMGR Compact Fluorescent Series Element Rodded Metal over Glass (glass lined) High Bay
Type No. Catalog No. Job. Name ELMGR Compact Fluorescent Series Element Glass (glass lined) High Bay PPLICTIONS pplications include large and small retail facilities, lobbies, conference rooms, auditoriums
More informationCable Tray Ladder, Trough, Channel, Under Floor, Shielded CH-117O
Cable Tray, Trough, Channel, Under Floor, Shielded C-117O Style Cable Tray Typical Installations Chalfant Cable Trays Tray When metal ladder cable trays came of age, they were used to support the new armored
More informationElectrical and Mechanical Supports Systems
Electrical and Mechanical Supports Systems Index - Mechanical & Electrical Support Systems This catalogue contains Mechanical & Electrical Support Systems information only as indicated below. For any additional
More informationDisconnect Enclosures
Type 12 Heavy-Duty Single & Multi-Door Data Sheet pplication Houses electrical controls and equipment Protects against circulating dust, falling dirt and dripping non-corrosive liquids Standards UL 508
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationJIB KITS BENCH OR FLOOR MOUNTED, 30 lb. CAPACITY
JIB KITS BENCH OR FLOOR MOUNTED, 30 lb. CAPACITY JIBS Jib kits feature either fixed or swing booms mounted on vertical columns and are painted polyester beige. The boom may be adjusted vertically higher
More informationPOWER BUTTON: 25mm (1") CONDUIT X 3048mm (10'-0") LONG TO HOUSE POWER AND CONTROL CABLES (SUPPLIED BY DIEBOLD)
R Easy-aire GX PNEUMTIC DELIVERY SYSTEM 24mm(") DI. PNEUMTIC TUBE SYSTEM 86G OPERTOR ND 8G CUSTOMER DETILS L962 CLL -8-999-6 OPERTOR CONTROL PNEL PROJECTION FILE NO. 8-26 REV. SUBJECT TO CHNGE W ITHOUT
More informationSpecifications. S&C Omni-Rupter Switches Outdoor Distribution (14.4 kv and 25 kv) Conditions of Sale
S&C Omni-Rupter Switches Outdoor istribution (14.4 kv and 5 kv) Specifications Conditions of Sale STNR: Seller s standard conditions of sale as set forth in Price Sheet apply. SPECIL TO THIS PROUCT: INCLUSIONS:
More informationDISCONTINUED PRODUCT POWER PROTECTION. Series 600 UPS. Multi-Module Three Phase 338 kva to 1000 kva; 60 Hz. Installation Manual
POWER PROTECTION Series 600 UPS Multi-Module Three Phase 338 kva to 1000 kva; 60 Hz Installation Manual TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.............................................1 1.0
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationGeneral characteristics
Multipole Industrial Connectors General characteristics The multipole connectors for industrial purposes are used in electric and electronic machinery, robots, electric panels, control equipments and wherever
More informationCable & Wire Management
Type 1 Screw over... 8-14 Type 1 Quick-onnect inge over... 15-20 Type 3R nviroshield... 21-24 Type 12... 25-31 eed-through Wireway Type 12... 32-35 eed-through Wireway Type 4X... 36-39 Wiring Trough Type
More informationClippard offers more types of miniature pneumatic cylinders for the MINIMATIC CYLINDER
MINIMATIC CYLINDER Clippard offers more types of miniature pneumatic cylinders for the designer s convenience, including: spring return, spring extend, air retract, double-acting and double rod models.
More informationREDI-RAIL - Accessories
Standard Splice Plates One pair including hardware provided with each straight section. Offset Reducing Splice Plates FLEX-MOUNT djustable Splice Plates 1 /4" hardware. Horizontally adjustable to 90. Vertically
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationData Bulletin. Wire Temperature Ratings and Terminations INTRODUCTION WHY ARE TEMPERATURE RATINGS IMPORTANT?
Data Bulletin March 2002 Lexington, KY, USA Wire Temperature Ratings and Terminations INTRODUCTION WHY ARE TEMPERATURE RATINGS IMPORTANT? Table 1: Insulation Type Figure 1: Figure 2: Ampacity of a 1/0
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationProduct Range Handbook
Product Range Handbook 1 Where to find us Building 144 Culham Number 1 Site Station Road CULHAM Oxon OX14 3DA Sales: +44 (0)1865 409300 Fax: +44 (0)1865 407991 2 INDEX PAGE ROUND BARS 4 SQUARE BAR 5 TEES
More informationLIF TING SOLUTIONS. Lifting Solutions
Center Pull Style... 484-485 Envirolox Protective Finish... 494 Eye Bolts...500 Eye Nuts... 499 Forged Center Pull...487 488 Forged Center Pull Stainless Steel...486 Kwik-Lok Lifting Pin...495 496 Hold
More informationCABLE MANAGEMENT SOLUTIONS CATALOGUE2003/04 A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS.
CLE MNGEMENT SOLUTIONS CTLOGUE2003/04 COMPLETE CLE MNGEMENT SOLUTION FOR COMMERCIL ND INDUSTRIL PPLICTIONS www.legrand.co.uk FSTRCK F31 FSTRCK F31 SYSTEM STEEL WIRE CLE TRY Legrand With a large range of
More informationT&B Cable Tray. In this section...
In this section... T& Cable Tray T& Cable Tray Overview... -260-261 luminum Tray... -262-309 Steel Tray... -310-333 One-Piece Tray... -334-357 Channel Tray... -358-373 Common ccessories... -374-376 Grounding
More informationTG/RB/2M/Web Rev.12/1/16. Pipe Hangers & Devices
TG/RB/2M/Web Rev.12/1/16 Pipe Hangers & Devices Pipe Welcome Hangers to PHD & Devices Manufacturing PHD Manufacturing, Inc. was founded in 1972 by a group of industry veterans with strong management, financial,
More informationETA-5 RAIL SYSTEMS. , Unified Industries, Inc. All Rights Reserved.
RAIL SYSTEMS PAGE 1 TABLE OF CONTENTS PAGE Rail Profiles...2-4 Rail Load Charts...5-6 ETA-4 & Hangers...7-10 Inspection Gate...11 ETA-4 & Load Trolleys...12-15 ETA-4 & Festoon Trolley...16-19 ETA-4 &
More informationSECTION PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More informationWIRE BASKET TRAY CANADIAN ELECTRICAL RACEWAYS INC.
CANADIAN ELECTRICAL RACEWAYS INC. WIRE BASKET TRAY Made of heavy-gauge zinc plated wire mesh, CER basket tray is ideal for your commercial or industrial cable management project. A full range of cable
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationC12. Grounding / Isolation / Electrical. Note: XX= finish code. DUPLEX AC OUTLET ASSEMBLY NETBAY AC OUTLET STRIP / BLANK STRIP.
Grounding / Isolation / Electrical DUPLEX C OUTLET SSEMBLY Phone: (99) 575- Fax: (99) 575-708 Modified:09/9/0 Part Number 0000xx 8 5 7 front bracket rear bracket outlet box outlet box cover 5 duplex receptacle
More informationRigid/Aluminum Conduit Bodies, Gaskets and Covers
Rigid/luminum Conduit odies, Gaskets and Covers Conduit odies, Covers and Gaskets Weatherproof oxes and Covers pplications Junction for branch conduits Series bodies for Rigid and IMC conduit maintain
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS ELECTRIC CONVECTION OVENS MODELS ECO4C ECO6C ML-52503 ML-52505 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 30943 (6-95) MODEL ECO4C/ECO6C
More informationCable & Wire Management
able & ire Management able & ire Management Lay-In ireway Type 1 Screw over... 8-14 Lay-In ireway Type 1 Quick-onnect inge over... 15-20 Lay-In ireway Type 3R EnviroShield... 21-24 Lay-In ireway Type 12...
More informationMDOTProjectwise\Documents\Reference Documents\Traffic Reference\Signals\Wayne County Special Details\Develop
MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Signals\Wayne County Special Details\Develop Green Orange Red White-black stripe G R "" phase Blue Black "B" phase White Green-black stripe
More informationSEISMIC RESTRAINTS Multi-Directional Bracing For Electrical Conduit, Cable Tray And Mechanical Piping Systems
SEISMIC RESTRAINTS Multi-Directional Bracing For Electrical Conduit, Cable Tray And Mechanical Piping Systems SYSTEMS THAT MAKE SENSE INTRODUCTION INTRODUCTION What is Seismic Bracing? Seismic forces are
More informationCOMPACT BUSWAY 40 & 60 AMP HOUSING
40 & 60 AMP HOUSING B40 & HOUSING Each Track Busway housing section consists of an extruded aluminum housing with an insulated strip containing copper conductors mounted on the top interior wall. The aluminum
More informationEngineer The Lift!! HOIST RINGS. Applied Load Changes With Sling Angle. Sample Calculation: DO S DON TS
H&O DIE SUPPLY, INC. 1-800-222-5441 sales@hodie.com HOIST RINGS 10 Adjustable Alloy Chain Sling... 10.16 Center Pull Style... 10.4-10.5 Envirolox Protective Finish... 10.11 Eye Bolts... 10.15 Eye Nuts...
More information[ ] ] [ 6a2O s6 Height B PW CABLE TRAY PW CABLE TRAY
PW CBE RY PW CBE RY Covers protect and contain cables. hey are highly recommended ray Covers to avoid damage to the tray contents and to protect against the elements. Some covers can also be attached to
More informationWire Mesh Safety Grips
Wire esh Safety Grips Leviton are built tough to provide the strength, reliability and gripping force required for today s demanding wire management applications. They are designed to distribute stress
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS ELECTRIC CONVECTION OVENS MODEL ECO4S ML-52501 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 30941 (6-95) MODEL ECO4S REPLACEMENT PARTS
More information35-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 35 kv Separable Insulated Connector (elbow) Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other
More informationSpring Test 7 due 05/03/2013
Spring Test 7 due 05/03/2013 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A raceway contains two 3-phase, 3-wire circuits that supply 38 ampere continuous
More informationORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and C-to-C dimension. C - C LOAD lb.
Fig. 2110 www.pipingtech.com/fig2110 Sway Strut with 4 of Adjustment Engineered spring supports option 1 option 2 ORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and
More informationCable Tray Straight Sections Pages Fittings Pages Inside Vertical Bends. 90 Page Page Page Page 1-15
Premier Ladder Tray When metal ladder cable trays came of age, they were used to support the new armored shielded power cables that were permitted outside the conduit environment. Utilities and industrial
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More information