Pipe hanger solutions

Transcription

1 Product catalog Middle East offering Pipe hanger solutions for commercial and industrial applications

2 B00 series B00 - Standard clevis hanger Pipe will not pinch when installing. 5 swing in either direction allows pipe to easily feed thru. Engineered design aligns bolt holes for quicker overhead installation. E A (Rod Size) Hanger Rod Not Included Component of State of California OSHPD Approved Seismic Restraints System B Bottom of pipe to top of hanger. * D F C Center of pipe to top of hanger. D Rod Take-Out Center of pipe to bottom of hanger rod. C E Minimum thread length of hanger rod B F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger. *SLIDE-RITE Clevis Hanger design, as shown above, for sizes 2, 2 /2,, 4, 5 & 6. Pat. No. 5,848,770 5,924,655 Nominal Pipe Size Rod Size A B C D Part No. in mm Std NFPA* in mm in mm in mm B00- " 5 "-6 "-6 2 " 54.0 " / 6" 2.8 B00- " 20 "-6 "-6 2 " 6.5 2" 50.8 " 28.6 B00- " 25 "-6 " " " 57. " 4.9 B00- " 2 "-6 "-6 " / 6" 68.2 / 6" 46.0 B00- " 40 "-6 "-6 4" 0.6 / 6" " 57. B00-2* 2" 50 "-6 "-6 4 " 4. 5 / 6" " 6.5 B00-2 * 2 " 65 "- "-6 5 " / 6" 00.0 / 6" 77.8 B00- " 80 "- "-6 6 " " / 6" 00.0 B00- " 90 "- "-6 7 " ". 4 / 6" 0.2 B00-4* 4" 00 5 "- "-6 7 " " " 9.7 B00-5* 5" 25 5 "- "- 8 " " " 52.4 B00-6* 6" 50 "-0 "- 0 5 / 6" / 6" " 77.8 B00-8 8" 200 "-0 "- 2 " / 6" " 8.0 B00-0 0" "-9 5 "- 5 " " " 22.7 B00-2 2" 00 7 "-9 5 "- 7 " " / 6" 246. B00-4 4" 50 " " " " B00-6 6" 400 " " " / 6" 29.7 B00-8 8" 450 " " " / 6" 60. B " 500 " " " " 422. B " 600 " " " " 47. B00-0 0" 750 " / 6" / 6" " B00-6 6" 900 " " " "

3 B00 - Standard clevis hanger B00 series Size range: /2" (5mm) to 6" (900mm) Material: Steel Function: Recommended for the suspension of non-insulated pipe or insulated pipe with a B5 shield. Note: When an oversized clevis is used, a pipe spacer should be placed over the cross bolt to assure that the lower U-strap will not move in on the bolt. When attaching seismic bracing to the clevis hangers, a Fig. CBS (cross bolt spacer) must be installed. See Seismic Restraints Approval Guidelines. Order pipe sleeves Fig. CBS-(pipe size) separately. Approvals: Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the Eaton s Tolco Seismic Restraint Systems Guidelines. Underwriter s Laboratories Listed in the USA (UL) and Canada (cul) for sizes /4" (20mm) thru 2" (00mm). Factory Mutual Engineering Approved (FM) for /4" (20mm) thru 2" (00mm) pipe. Conforms to Federal Specification WW-H-7E & A-A-92A, Type and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type. Also available to accommodate rod schedule per National Fire Protection Association (NFPA) Pamphlet. Maximum temperature: 650 F (4 C). Standard finish: Plain, Electro-Galvanized, DURA GREEN, or Hot-Dip Galvanized also available in Stainless Steel Order by: Part number and finish. Special note: Do not use the dimensions shown in the B00 chart for NFPA hanger sizes. Contact customer service for NFPA rod sizing on " (5mm) thru 2" (00mm) pipe. Part numbers will be NFPA-pipe size. Load values based on safety factor of.5 E Adjustment F Design Load Approx. Wt./00 Part No. in mm in mm Lbs. kg Lbs. kg B00-2 " / 6 " B00-2 " 6.5 " B00-2 " " B00-2 " " B00-2 " 6.5 / 6 " B " " B " 6.5 2" B00-2 " 6.5 2" B00-2 " 6.5 2" B " 6.5 2" B " 6.5 2" B00-6 " " B00-8 " / 6 " B00-0 " / 6 " B00-2 " " B00-4 4" " B00-6 4" / 6 " B " 4. 5 / 6 " B " " B " " B00-0 5" " B00-6 5" / 6 "

4 M00 series M00 - Standard clevis hanger D Size Range: " - 6" Nominal Pipe (schedule 40/80); Intermediate sizes also available Material: Steel Function: Recommended for the suspension of non-isulated or insulated pipe Approvals: Conforms to Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type. Finish: Zinc plating per ASTM Standard B6 SC or Hot-Dip galvanized after fabrication per ASTM A2 Order by: Part Number, size, & finish Notes: Full range of sizes available to match outer diameters of Rubber Support Inserts (RSI), providing a simple and effective support solution for insulated pipes Load values based on safety factor of.5 For intermediate sizing of pipe and insulation thickness, see back page. Part No. Nominal Pipe Size Pipe OD A B C D Approx. Wt./00 in mm mm lbs. kg Part No. Nominal Pipe Size Pipe OD A B C D Loading kg Loading kg Approx. Wt./00 in mm mm lbs. kg M00- /2 M00- /4 /2" /4" M00-8 8" M00-2mm M00- " M00- /4 /4" M00- /2 /2" M00-2 2" M00-65mm M00-2 /2 2 /2" M00-77mm M00-8mm M00-86mm M00- " M00-9mm M00-99mm M00- /2 /2" M00-0mm M00-07mm M00-0mm M00-4 4" M00-22mm M00-27mm M00-7mm M00-5 5" M00-49mm M00-54mm M00-6mm M00-6 6" M00-74mm M00-79mm M00-90mm M00-206mm M00-242mm M00-0 0" M00-284mm M00-296mm M00-2 2" M00-8mm M00-500mm M00-4 4" M00-74mm M00-88mm M00-400mm M00-6 6" M00-42mm M00-4mm M00-8 8" M00-47mm M00-48mm M00-507mm M " M00-522mm M00-54mm M00-56mm M00-575mm M00-587mm M " M00-6mm M00-0 0" M00-6 6"

5 Fig Trimline adjustable band hanger Fig. 200F - Trimline adjustable band hanger with felt lining for copper tubing Fig. 200C - Trimline adjustable band hanger with plastic coated Fig. 200S - Trimline adjustable band hanger with removable nut (For sizes " thru 2") Fig. 200 series Size range: Fig /2" (5mm) thru 8" (200mm) pipe Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation. Features: " (5mm) thru 2" (50mm) sizes have flared edges for ease of installation on all pipe types and protects CPVC plastic pipe from abrasion. Captured knurled nut design (flared top) on " thru 2" sizes keep nut from separating with hanger. Hanger is easily installed around pipe. /2" (5mm), /4" (20mm), and 2 /2" (65mm) thru 8" (200mm)) Spring tension on nut holds it securely in hanger before installation. Knurled nut is easily removed. For /2" (5mm) and /4" (20mm) sizes with non-captured knurl nuts order Fig. 200S Approvals: Underwriters Laboratories listed ( /2" (5mm) thru 8" (200mm)) in the USA (UL) and Canada (cul) for steel and CPVC plastic pipe and Factory Mutual Engineering Approved ( /4" (20mm) thru 8 (200mm)). Conforms to Federal Specifications WW-H-7E & A-A-92A, Type 0 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 0. A Overall Height B Center of pipe to top of knurled hanger rod nut. D Top of pipe to bottom of hanger rod nut. Fig to Fig /2 & 200- /4 A B D Fig /2 to Maximum temperature: 650 F (4 C) Finish: Pre-Galvanized. Stainless Steel materials will be supplied with (2) hex nuts in place of a knurl nut. Order by: Part number and pipe size Note: For metric hanger rod sizes add the metric rod size to the figure number. Example: 200M8- /2 or 200M0- /2 Load values based on safety factor of.5 Fig. 200C 200C- /2 shown Fig. 200F 200F- /2 shown Fig. 200 shown with captured nut thru 2 sizes only Fig. 200 & Fig. 200S shown with non-captured nut Part No.** Nominal Pipe Size Rod Size A B D Max. Rec. Load Approx. Wt./00 in. mm in mm** in mm in mm in mm lbs. kg lbs. kg 200- " 5 "-6 M8 or M0 " " 66.7 " " 20 "-6 M8 or M0 " " 6.5 / 6" " 25 "-6 M8 or M0 " " 66.7 " " 2 "-6 M8 or M0 " " " " 40 "-6 M8 or M0 7 " " 7.0 / 6" " 50 "-6 M8 or M0 4 " 4. " 76. / 6" " 65 "-6 M0 5 5 " " / 6" " 75 "-6 M0 5 7 " 49. 4" 0.6 " " 90 "-6 M0 7 " ". 2 / 6" " 00 "-6 M0 7 " 87. 5" 27.0 " " 25 "- M2 9 " " 58.7 " " 50 "- M2 0 " " " " 200 "- M2 ".4 8 " "

6 Rubber lined split clamps Rubber lined split clamp Size range: "- 8" Standard finish: electro-zinc plated complies with ASTM B6 Function: design for suppressing vibration and sound "A" bolt thread size: M8 & M0 for all part #'s Note: twin threads with suspension nuts for flexibility M8 & M0 Design load: safety factor of Part No. Dimensions (mm) Pipe OD (mm) B C D min max Steel Nom (OD) Copper Nom (OD) UPVC/PE Cast Iron Nom (OD) Rubber (mm) Locking Screw Min Torque " (4) x.5 M6/ , x.5 M6/ " (22) x.5 M6/ " (27) x.5 M6/ " (4) x.5 M6/ " (42) 42 40, x.5 M6/ " (48) " 20x.5 M6/ x4.5 M6/ " (60) " 20x4.5 M6/ , x4.5 M6/ " (7) x4.5 M6/ , x4.5 M6/ " (89) - - 8, 90 " 20x4.5 M6/ " (02) 02, x5.5 M8/ " (4) " 20x5.5 M8/ x5.5 M8/ x5.5 M8/ x5.5 M8/ " (4) " 20x5.5 M8/ x5.5 M8/ " (68) " 20x5.5 M8/ " (29) " 20x5.5 M8/ x5.5 M8/ Design Load (kg) 6

7 s SCPH-ME Non-rubber lined split clamp Size range: "- 8" Standard finish: electro-zinc plated complies with ASTM B6 Function: use as ceiling suspension as well as vertical piping wall mounting Split clamp pipe hangers "A" bolt thread size: M8 & M0 for all part #'s Design load: safety factor of Note: twin threads with suspension nuts for flexibility M8 & M0 Non-rubber lined split clamp SCPH-ME (mm) ax Dimension (mm) Pipe OD (mm) Steel Copper Design Nom Nom Locking Min. Load Part No. B C D min max (OD) (OD) UPVC/PE Screw Torque (kg) Steel Copper Cast " (4) Iron- - Locking - - Qty - - Min. M6x6 80 Design2 Nom (OD) Nom 27 5 (OD) 20 UPVC/PE 5 8 Nom - - (OD) 5 Screw - - (box) - - Torque M6x6 80 Load (kg) /8" (4) " (22) 22 M6x M6x " (27) M6x M6x " (4) M6x /2" (22) " (42) 42 M6x6 8, 40, M6x /4" (27) M6x M6x " (48) " (48) M6x " (4) 5 2 M6x M6x /4" (42) , 57 40, 46 2" (60) - - M6x " (60) 80 M6x , 67 M6x M6x " (7) M6x /2" (48) /2" (48) M6x M6x M6x M6x " (60) " " (89) (60) - - M6x20 8, " (89) 80 M6x Size range: / " (02) 02, M8x , 67 M6x " (4) Standard 08 0 finish: 4" electro-zinc (4) M8x /2" (7) plated 25 complies M6x20 25 with M8x ASTM B6 M6x M8x M8x Function: M6x20 use as 50ceiling " (4) " (40) M8x " (89) suspension as well as , " -(89) - 59 M6x M8x vertical piping wall mounting /2" (02) 02, " (68) 68 M8x " (65) 00 M8x "A"- -Bolt Thread - - Size: - - M8x " (4) " (4) M8x " (29) M8 - -& M0 220 for all 8" part (29) #'sm8x M8x M8x Note: twin threads with 4 M8x Cast Iron Nom (OD) suspension nuts for flexibility M8 & M0 M8x

8 B7 series B7 - Standard riser clamp B7F - Felt lined standard riser clamp for copper tubing B7C - PVC Coated standard riser clamp Size range: (B7) /2" (5mm) thru 0" (760mm) pipe (B7F) /2" (5mm) thru 2 /2" (65mm) copper tubing (B7C) /2" (5mm) thru 6" (50mm) pipe Material: Steel Insulation material: (B7F) /8" (.2mm) thick felt. Function: Used for supporting vertical piping. Approvals: Underwriters Laboratories Listed in the USA (UL), Canada (cul) /4" (20mm) - 8" (200mm). Factory Mutual Engineering Approved (FM) for plain and electro-galvanized zinc, /4" (20mm) thru 8" (200mm). Conforms to Federal Specification WW-H-7E & A-A-92A, Type 8 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 8. Maximum temperature: 650 F (4 C) Finish: Plain. Contact customer service for alternative finishes and materials. Order by: (B7 and B7C) pipe size and finish. B7F is available for Iron Pipe Size, consult factory. Load values based on safety factor of.5 Load values shown are for standard B7 only. Design Load Bolt Size L Bolts and Nuts Included B7C B7F B7 Pipe Size L Design Load Approx. Wt./00 Part No. in mm in mm Bolt Size lbs kg lbs kg B7- " 5 9" "-6x " B7- " 20 9 " 24.9 "-6x " B7- " / 6" "-6x " B7- " 2 0" "-6x " B7- " 40 0 " 260. "-6x " B7-2 2" 50 0 " 27.0 "-6x " B7-2 " 65 " "-6x " B7- " 80 5 / 6" 0.2 "-6x " B7- " 90 2 " 4. "-x " B7-4 4" " 27.0 "-x " B7-5 5" 25 4" 55.6 "-x " B7-6 6" 50 5 / 6" 85.8 "-x2" B7-8 8" " "-x2 " B7-0 0" / 6" "-x2 " B7-2 2" 00 2 / 6" "-x" B7-4 4" / 6" "-x" B7-6 6" " "-0x " B7-8 8" " 7.4 "-0x " B " " "-0x " B " " "-0x " B7-0 0" " "-9x " Notes: For ductile iron (D.I.) pipe use part number B7DIpipe size. Contact us Engineering for more information. 8

9 M7 series M7 - Riser clamp Size range: /2" - 0" Nominal Pipe (schedule 40/80) Function: Used for supporting vertical piping Approvals: Confoms to Manufactuers Standardization Society ANSI/MSS SP-69 & SP-58, Type 8. Finish: Zinc plating per ASTM Standard B6 SC or Hot-Dip galvanized after fabrication per ASTM A2 Order by: Part Number, size, & finish Load values based on safety factor of.5 M7 Design Load Bolt Size Bolts and Nuts Included L Pipe Size Length Strip Width Strip Thickness Bolt Size Loading Approx. Wt./00 Part No. in mm mm mm mm in kg lbs kg M " M " M " M " M " M / 6 " M / 6 " M / 6 " M " M " 50 4 M " M " M " M " M " M7-4 4" " M7-6 6" " M7-8 8" " M " " M " " M7-0 0" "

10 M2400 series M Pipe strap Size range: ½" 6" Nominal Pipe (schedule 40/80); Intermediate sizes also available Function: Recommended for clamping plain or insulated pipes to structural channel supports such as trapeze hangers, floor stands or wall brackets Material: Steel Finish: Zinc plating per ASTM Standard B6 SC or Hot-Dip galvanized after fabrication per ASTM A2 Approvals: Conforms to Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 26. Order by: Part Number, size, & finish Note: Full range of sizes available to match outer diameters of Rubber Support Inserts (RSI),providing a simple and effective support solution for insulated pipes Load values based on safety factor of.5 Part No. Pipe Size OD Width Slot Size A B Loading Thickness Loading Approx. Wt./00 mm mm mm mm mm mm kg lbs kg M2400- /2 ½" Ø M2400- /4 ¾" Ø M2400- " 25 2 Ø M2400- /4 ¼" Ø M2400- /2 ½" Ø M Ø M mm Ø M /2 2 ½" x M mm x M2400-8mm x M mm x M2400- " x M mm x M mm x M2400- /2 ½" x M2400-0mm x M mm x M2400-0mm x M " x M mm x M mm x M2400-7mm x For intermediate sizing of pipe and insulation thickness, see back page. Part No. Pipe Size OD Width Slot Size A B Thickness Approx. Wt./00 mm mm mm mm mm mm kg lbs kg M " x M mm x M mm x M2400-6mm x M " x M mm x M mm x M mm x M mm x M " x M2400-2mm 2 8 6x M mm x M " x M mm x M mm x M " x M2400-8mm x M mm x M " x M mm x M mm x M mm x M " x M mm x M2400-4mm x M " x M mm x M mm x M mm x M " x M mm x M mm x M mm x M mm x M mm x M " x M2400-6mm x M " x M " x Eaton

11 M88 - U-Bolt M88 series Size range: ½ 6 Nominal Pipe (schedule 40/80); Intermediate sizes also available Function: recommended to grip, guide or support plain or insulated pipes Material: Steel Finish: Zinc plating per ASTM Standard B6 SC or Hot-Dip galvanized after fabrication per ASTM A2 Approvals: Conforms to Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 24. Order by: Part number, size, & finish Notes: -Provided with 4 hex nuts -Full range of sizes available to match outer diameters of Rubber Support Inserts (RSI), providing a simple and effective support solution for insulated pipes Load values based on safety factor of.5 Nominal OD X Y Z Loading Approx. Wt./00 Part no. pipe size in mm mm mm mm Rod dia. kg lbs kg M88-½ ½ M M88-¾ / M M M M88- ¼ ¼ M M88- ½ ½ M M M M88-65mm M M88-2 ½ 2 ½ M M88-77mm M M88-8mm M M88-86mm M M M M88-9mm M M88-99mm M M88- ½ ½ M M88-0mm M M88-07mm M M88-0mm M M M M88-22mm M M88-27mm M M88-7mm M M M M88-49mm M M88-54mm M M88-6mm M M M M88-74mm M M88-79mm M M88-90mm M M88-206mm M For intermediate sizing of pipe and insulation thickness, see back page. Nominal OD X Y Z Loading Approx. Wt./00 Part no. pipe size in mm mm mm mm Rod dia. kg lbs kg M M M88-2mm M M88-242mm M M M M88-284mm M M88-296mm M M M M88-8mm M M88-50mm M M M M88-74mm M M88-88mm M M88-400mm M M M M88-42mm M M88-4mm M M M M88-47mm M M88-48mm M M88-507mm M M M M88-522mm M M88-54mm M M88-56mm M M88-575mm M M88-587mm M M M M88-6mm M M M M M

12 Insulation protection shield Selection tables for: B5 Insulation Protection Shield B5 Insulation Protection Shield with Loc Tabs B54 Short Insulation Protection Shield B55 Short Insulation Protection Shield with Loc Tabs Nominal pipe or tubing size Insulation thickness in. (mm) " (2.7mm) " (9.0mm) " (25.4mm) " (8.mm) 2" (50.8mm) 2 " (6.5mm) " (76.2mm) 4" (0.6mm) " (5) X 2X X 5X 7X " (20) 2X X X 5X 7X " (25) 2X X 4X 6X 8X " (2) X 4X 4X 7X 8X " (40) X 4X 5X 7X 9X " (50) 4X 5X 6X 8X 9X 0X* X* -- 2 " (65) 5X 6X 7X 9X 0X* X* X* Y* " (80) 6X 7X 8X 9X 0X* X* 2Y* 4Z " (90) 7X 8X 9X 0X* X* 2Y* Y* 5Z 4" (00) 8X 9X 9X 0X* X* 2Y* Y* 5Z 5" (25) Y* Y* 2Y* Y* 4Z 6Z 6" (50) Y* 2Y* Y* 4Z 5Z 7Z 8" (200) Y* 4Z 5Z 6Z 7Z 9Z 0" (250) Z 6Z 7Z 8Z 9Z 2Z 2" (00) Z 8Z 9Z 20Z 2Z 2Z 4" (50) Z 9Z 20Z 2Z 22Z 24Z 6" (400) Z 2Z 22Z 2Z 24Z 26Z 8" (450) Z 2Z 24Z 25Z 26Z 28Z 20" (500) Z 25Z 26Z 27Z 28Z 0Z 24" (600) Z 29Z 0Z Z 2Z Z *When selecting B54 or B55, replace X or Y designation with Z. Nominal pipe or tubing size Insulation thickness in. (mm) " (2.7mm) " (9.0mm) " (25.4mm) " (8.mm) 2" (50.8mm) 2 " (6.5mm) " (76.2mm) 4" (0.6mm) " (5) " (20) " (25) " (2) " (40) " (50) " (65) " (80) " (90) " (00) " (25) " (50) " (200) " (250) " (00) " (50) " (400) " (450) " (500) " (600)

13 B5 - Insulation protection shield B5 - Insulation protection shield with loc tabs Insulation protection shield Material: Steel (Stainless steel available) Function: Designed to protect pipe insulation when used with hangers. Approvals: Complies with Federal Specification WW-H-7E & A-A-92A Type 4 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58 Type 40. Finish: Pre-Galvanized (ASTM A65 G90) Order by: Part number and finish. Note: See Selection Tables on page 2 for proper sizing. Stock Size B5 L Shield I.D. (Inside Dia.) L Shield I.D. (Inside Dia.) Stock Size B5 same dimension as B5, but with bottom tabs for centering and securing the shield to hanger. B5 Part Part Stock size L Shield I.D. Approx. Wt./00 Pipe hanger size no. no. in. (mm) in. (mm) in. (mm) Lbs. (kg) in. (mm) B5-X B5-X 8 Ga. (.2) 2 (04.8).90 (48.2) 50 (22.7) /2 (40) B5-2X B5-2X 8 Ga. (.2) 2 (04.8) 2.8 (60.4) 62 (28.) 2 (50) B5-X B5-X 8 Ga. (.2) 2 (04.8) 2.88 (7.) 75 (4.0) 2 /2 (65) B5-4X B5-4X 8 Ga. (.2) 2 (04.8).50 (88.9) 92 (4.7) (80) B5-5X B5-5X 8 Ga. (.2) 2 (04.8) 4.00 (0.6) 04 (47.2) /2 (90) B5-6X B5-6X 8 Ga. (.2) 2 (04.8) 4.50 (4.) 8 (5.5) 4 (00) B5-7X B5-7X 8 Ga. (.2) 2 (04.8) 5.00 (27.0) 29 (58.5) 5 (25) B5-8X B5-8X 8 Ga. (.2) 2 (04.8) 5.56 (4.2) 47 (66.7) 5 (25) B5-9X B5-9X 6 Ga. (.5) 2 (04.8) 6.64 (68.6) 29 (99.) 6 (50) B5-0X B5-0X 6 Ga. (.5) 2 (04.8) 7.64 (94.0) 25 (4.7) 8 (200) B5-X B5-X 6 Ga. (.5) 2 (04.8) 8.64 (29.4) 286 (29.7) 8 (200) B5-0Y -- 6 Ga. (.5) 8 (457.2) 7.64 (94.0) 77 (7.0) 8 (200) B5-Y -- 6 Ga. (.5) 8 (457.2) 8.64 (29.4) 424 (92.) 8 (200) B5-2Y -- 6 Ga. (.5) 8 (457.2) 9.64 (244.8) 475 (25.4) 0 (250) B5-Y -- 6 Ga. (.5) 8 (457.2) 0.76 (27.) 529 (29.9) 0 (250) B5-4Z -- 4 Ga. (.9) 24 (609.6).76 (298.7) 964 (47.) 2 (00) B5-5Z -- 4 Ga. (.9) 24 (609.6) 2.76 (24.) 045 (474.0) 2 (00) B5-6Z -- 4 Ga. (.9) 24 (609.6) 4.00 (55.6) 46 (59.8) 4 (50) B5-7Z -- 4 Ga. (.9) 24 (609.6) 5.00 (8.0) 227 (556.5) 6 (400) B5-8Z -- 4 Ga. (.9) 24 (609.6) 6.00 (406.4) 08 (59.) 6 (400) B5-9Z -- 4 Ga. (.9) 24 (609.6) 7.00 (4.8) 9 (6.8) 8 (450) B5-20Z -- 2 Ga. (2.6) 24 (609.6) 8.00 (457.2) 2064 (96.2) 8 (450) B5-2Z -- 2 Ga. (2.6) 24 (609.6) 9.00 (482.6) 278 (987.9) 20 (500) B5-22Z -- 2 Ga. (2.6) 24 (609.6) (508.0) 2292 (09.6) 20 (500) B5-2Z -- 2 Ga. (2.6) 24 (609.6) 2.00 (5.4) 2406 (09.) 24 (600) B5-24Z -- 2 Ga. (2.6) 24 (609.6) (558.8) 2520 (4.) 24 (600) B5-25Z -- 2 Ga. (2.6) 24 (609.6) 2.00 (584.2) 264 (94.8) 24 (600) B5-26Z -- 2 Ga. (2.6) 24 (609.6) (609.6) 275 (248.7) 24 (600) B5-27Z -- 2 Ga. (2.6) 24 (609.6) (65.0) 2862 (298.2) 0 (750) B5-28Z -- 2 Ga. (2.6) 24 (609.6) (660.4) 2980 (5.7) 0 (750) B5-29Z -- 2 Ga. (2.6) 24 (609.6) (685.8) 094 (40.4) 0 (750) B5-0Z -- 2 Ga. (2.6) 24 (609.6) (7.2) 208 (455.) 0 (750)

14 Short insulation protection shield B54 - Short insulation protection shield B55 - Short insulation protection shield with loc tabs Material: Steel (Stainless steel available) Function: Designed for protection of foam, fiberglass, or high density insulation when used with pipe hangers. Finish: Pre-Galvanized (ASTM A65 G90) Order by: Part number and finish. Note: See Selection Tables on page 2 for proper sizing. L Stock Size B54 Shield I.D. (Inside Dia.) L Shield I.D. (Inside Dia.) Stock Size B55 B55 same dimension as B54 but with bottom tabs for centering and securing the shield to hanger. Part Part Stock size L Shield I.D. Approx. Wt./00 Pipe hanger size no. no. in. (mm) in. (mm) in. (mm) Lbs. (kg) in. (mm) B54-X B55-X 8 Ga. (.2) 8 (20.2).90 (48.2) 6 (6.) /2 (40) B54-2X B55-2X 8 Ga. (.2) 8 (20.2) 2.8 (60.4) 45 (20.4) 2 (50) B54-X B55-X 8 Ga. (.2) 8 (20.2) 2.88 (7.) 54 (24.5) 2 /2 (65) B54-4X B55-4X 8 Ga. (.2) 8 (20.2).50 (88.9) 66 (29.9) (80) B54-5X B55-5X 8 Ga. (.2) 8 (20.2) 4.00 (0.6) 75 (4.0) /2 (90) B54-6X B55-6X 8 Ga. (.2) 8 (20.2) 4.50 (4.) 84 (8.) 4 (00) B54-7X B55-7X 8 Ga. (.2) 8 (20.2) 5.00 (27.0) 9 (42.2) 5 (25) B54-8X B55-8X 8 Ga. (.2) 8 (20.2) 5.56 (4.2) 05 (47.6) 5 (25) B54-9X B55-9X 8 Ga. (.2) 8 (20.2) 6.64 (68.6) 26 (57.) 6 (50) B54-0Z B55-0Z 8 Ga. (.2) 2 (04.8) 7.64 (94.0) 28 (98.9) 8 (200) B54-Z B55-Z 8 Ga. (.2) 2 (04.8) 8.64 (29.4) 247 (2.0) 8 (200) B54-2Z B55-2Z 8 Ga. (.2) 2 (04.8) 9.64 (244.8) 27 (2.8) 0 (250) B54-Z B55-Z 8 Ga. (.2) 2 (04.8) 0.76 (27.) 04 (7.9) 0 (250) B54-4Z B55-4Z 8 Ga. (.2) 2 (04.8).76 (298.7) 2 (50.6) 2 (00) B54-5Z B55-5Z 8 Ga. (.2) 2 (04.8) 2.76 (24.) 60 (6.) 2 (00) 4

15 Rubber support insert Rubber Support Insert Better than wood or foam products Resistant to deterioration and distortion from exposure to moisture Dimensional accuracy Noise and vibration dampening Locking upper and lower part design improves installation simplicity and reduces labor Thermal conductivity: 0.4 W/m C Density: 200 Kg/m Load capacity: meets max expected operating weight of piping systems for spans suggested by MSS SP-69 BS-974-: 974 compliant Temperature range: -20 C to 0 C SERIES B-LINE 50MM B-LINE SERIES 50MM Standard widths Nominal pipe size Insert width /2" - 2" 25mm 2" - 5" 8mm 6"+ 50mm Nom. pipe size Sch. 40 steel pipe OD " mm in mm in mm " 9mm " 25mm " 2mm " 8mm 2" 50mm 2 " 65mm " 75mm RSI525 RSI5925 RSI52525 RSI5225 RSI5825 RSI55025 RSI56525 RSI RSI2025 RSI20925 RSI RSI20225 RSI20825 RSI RSI RSI RSI2525 RSI25925 RSI RSI25225 RSI25825 RSI RSI RSI RSI225 RSI2925 RSI22525 RSI2225 RSI2825 RSI25025 RSI26525 RSI RSI4025 RSI40925 RSI RSI40225 RSI40825 RSI RSI RSI RSI5025 RSI50925 RSI RSI50225 RSI50825 RSI RSI RSI RSI658 RSI6598 RSI65258 RSI6528 RSI6588 RSI65508 RSI65658 RSI RSI808 RSI8098 RSI80258 RSI8028 RSI8088 RSI80508 RSI80658 RSI RSI908 RSI9098 RSI90258 RSI9028 RSI9088 RSI90508 RSI90658 RSI RSI008 RSI0098 RSI00258 RSI0028 RSI0088 RSI00508 RSI00658 RSI RSI258 RSI2598 RSI25258 RSI2528 RSI2588 RSI25508 RSI25658 RSI RSI5050 RSI50950 RSI RSI50250 RSI50850 RSI RSI RSI RSI20050 RSI RSI RSI RSI RSI RSI RSI RSI25050 RSI RSI RSI RSI RSI RSI RSI RSI0050 RSI00950 RSI RSI00250 RSI00850 RSI RSI RSI RSI5050 RSI50950 RSI RSI50250 RSI50850 RSI RSI RSI RSI40050 RSI RSI RSI RSI RSI RSI RSI RSI45050 RSI RSI RSI RSI RSI RSI RSI RSI50050 RSI RSI RSI RSI RSI RSI RSI RSI60050 RSI RSI RSI RSI RSI RSI RSI

16 Selection for common pipe/insulation sizes Nom Appropriate size for insulation / RSI thickness pipe size 9mm 25mm 2mm 8mm 50mm ½" 2"* or 60 2-½"* or ¾" " 2-½"* or ¼" "* or 4 ½" "* or " ½" 4"* or "* or " 27 5"* or "* or ½" 5"* or "* or " 54 6"* or "* or 29 5" "* or " 206 8"* or "* or 27 8" 0"* or "* or 24 0" 2"* or " " 6"* or "* or 457 6" 8"* or " 20"* or " *Indicates nominal pipe size Eaton 000 Eaton Boulevard Cleveland, OH 4422 United States Eaton.com B-Line Division 509 West Monroe Street Highland, IL Eaton.com 207 Eaton All Rights Reserved Printed in USA Publication No. CA0002EN October 207 Eaton is a registered trademark. All other trademarks are property of their respective owners. Eaton reserves the right to make changes to the specifications, materials, equipment, prices, or the availability of products at any time without prior notice. While every effort has been made to assure the accuracy of information contained in this catalog at the time of publication, we cannot accept responsibility for inaccuracies resulting from undetected errors or omissions.