AAMA/WDMA/CSA 101/I.S.2/A NAFS North American Fenestration Standard/Specification for windows, doors, and skylights

Transcription

1 AAMA/WDMA/CSA 101/I.S.2/A NAFS North American Fenestration Standard/Specification for windows, doors, and skylights Registered trade-mark of American Architectural Manufacturers Association Registered trade-mark of Window & Door Manufacturers Association

2 American Architectural Manufacturers Association 1827 Walden Office Square, Suite 550 Schaumburg, Illinois USA Copyright American Architectural Manufacturers Association 2008 Window & Door Manufacturers Association 1400 East Touhy Avenue, Suite 470 Des Plaines, Illinois USA Copyright Window & Door Manufacturers Association 2008 Canadian Standards Association A not-for-profit private sector organization 5060 Spectrum Way, Suite 100 Mississauga, Ontario, Canada L4W 5N To purchase CSA Standards and related publications, visit CSA s Online Store at or call toll-free or ISBN Technical Editor: Vanessa Mitchell 2008 Published by AAMA, WDMA, and CSA in January All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher.

3 American Architectural Manufacturers Association NAFS North American fenestration Standard/ Specification for windows, doors, and skylights Contents Preface vii 0 Introduction General Applicability Content Performance classes and levels Performance classes Guidance for the specifier/purchaser Performance grade (PG) designations Side-hinged door systems Positive and negative design pressure (DP) Water penetration resistance testing and performance Operation/cycling performance Short-form specification 6 1 Scope General Terminology Units of measurement 7 2 Reference publications 8 3 Definitions 18 4 General requirements General Gateway performance requirements General Alternative minimum test sizes for Performance Class R products (optional) Performance grades (PG) Assignment of performance grade (PG) Optional performance grades (PG) Product designations General Primary designator Secondary designator Dual windows or dual doors General Requirements 45 5 Testing Testing sequence Test specimen requirements General Composite units and combination assemblies Alterations Specimen size Test specimen installation Testing methods Operating force and force to latch 50 January 2008 iii

4 AAMA/WDMA/CSA 101/I.S.2/A American Architectural Manufacturers Association Air leakage resistance test Water penetration resistance test Uniform load tests Forced-entry resistance test Auxiliary (durability) tests Condensation resistance (optional) Thermal transmittance (optional) Acoustical performance (optional) Impact performance (optional) Laboratory test report 75 6 Materials Material tolerance Glazing and glass Reference standards General requirements Glazing selection Removable multiple glazing panels Plastic glazing Framing/cladding materials General Wood Wood flush and molded fiber doors Vinyl Cellular PVC Aluminum Fiberglass Steel Cellulosic composite materials Fiber-reinforced PVC Acrylonitrile-butadiene-styrene (ABS) Doorlite insert frame materials Other materials 87 7 Components Hardware General Hung window hardware Casement, awning, hopper, and projected window hardware Door hardware Hinged window hardware Tropical window hardware Dual-action window hardware Fasteners Reinforcing Weatherstrip Insect screens Sealants Coatings/finishes Mullions Mullion rating Composite units Combination assemblies Field mulling without manufacturer s involvement 98 iv January 2008

5 American Architectural Manufacturers Association NAFS North American fenestration Standard/ Specification for windows, doors, and skylights Windload deflection Operational interference Vertical (dead load) deflection Integral ventilating systems/devices Blinds in dual-glazed products Setting blocks Dividers (muntins) True divided lites Simulated divided lites, removable grids, and grills Fenestration type and test size General Product dimensions and tolerances Dimensions Tolerances Qualification of designs, configurations, and assemblies General Geometry and components Operation and orientation Composite units and unique framing members Specialty products, basement windows, hinged windows, side lites, and transoms Specialty products Basement windows Hinged windows Side lites and transoms Alternative minimum test sizes and minimum performance grades (PG) for selected Class R products (optional) 110 Annexes A (informative) Contact information for standards development organizations 118 Tables 1 Gateway requirements 28 2 U.S. (only) optional performance grades (PG) 30 3 Canada (only) optional performance grades (PG) 31 4 Optional performance grades (PG) for unit skylights, TDDs, and roof windows 32 5 Product types 36 6 Canadian (only) operating force requirements 51 7 U.S. (only) operating force requirements 52 8 Maximum allowable air leakage 54 9 Canadian (only) air infiltration/exfiltration levels Deflection limits for sash/leaf torsion test Deflection limits for sash vertical deflection test Deflection limits for sash/leaf concentrated load test on latch rail Deflection limits for vertical concentrated load test Deflection limit for vertical concentrated load test on intermediate frame rails Loads for distributed load test Loads for stabilizing arm load test Load for hold-open arm/stay bar test Deflection limits for sash blocked operation test Operation/cycling performance (side-hinged door systems) Allowable IGU glass loads for Examples 1 and 2 in Clause Plastic glazing combustibility classes 83 January 2008 v

6 AAMA/WDMA/CSA 101/I.S.2/A American Architectural Manufacturers Association 22 Door hardware reference Standards Requirements for fasteners and reinforcing Requirements for exterior finishes Window assembly qualification Alternative minimum test sizes and associated minimum performance grades (PG) for selected Class R products Gateway performance requirements 111 Figures 1 Short-form specification 6 2 Primary designator (Example 1) 33 3 Primary designator (Example 2) 34 4 Primary designator (Example 3) 35 5 Product type illustrations 37 6 Examples of specialty products 40 7 Secondary designator (Example 1) 43 8 Secondary designator (Example 2) 44 9 Secondary designator (Example 3) Corner sealant detail Test specimen mounting Set-up for thermoplastic corner weld test Set-up for sash/leaf torsion test Set-up for sash vertical deflection test Perpendicular load for sash/leaf concentrated load test on latch rail Parallel load for sash/leaf concentrated load test on latch rail Set-up for vertical concentrated load test Set-up for vertical concentrated load test on intermediate frame rails Set-up for distributed load test Set-up for stabilizing arm load test Set-up for hold-open arm/stay bar test Set-up for awning, hopper, projected hardware load test Set-up for unit dead load test Test report summary of results Mullion types and applications Product dimension measurement Window assembly qualification Typical configurations Side-hinged door assembly qualification 107 vi January 2008