New Gateway 101/I.S.2/A440

Transcription

1 Architectural Testing Informational Bulletin #16 March 7, 2005 Topic: Comparison of the new AAMA/WDMA/CSA 101/I.S.2/A to the previously published industry standards. The purpose of this ATI-TIPS Bulletin is to provide manufacturers, architects, and specifiers with information regarding revisions and additional requirements specified in the recently approved standard for windows, doors, and skylights. The information provided in this Bulletin is not specific to any one manufacturer or product type. This Bulletin is intended to be advisory only and highlights only the significant changes. Reference must be made to the applicable specification for determination of the comprehensive requirements. This TIPS bulletin reviews the following specifications: ANSI/AAMA/NWWDA 101/I.S.2-97, Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors AAMA/WDMA 101/I.S. 2/NAFS-02, Voluntary Performance Specifications for Windows, Skylights and Glass Doors AAMA/WDMA/CSA 101/I.S. 2/A440-05, Standard/Specification for Windows, Doors and Unit Skylights Important Certification Information The American Architectural Manufacturers Association (AAMA) has officially approved AAMA/WDMA/CSA 101/I.S. 2/A440-05, Standard/Specification for Windows, Doors and Unit Skylights for use in the AAMA Certification Program as of March 1, Until further notice AAMA will allow certification to all three of the aforementioned documents. The following table and subsequent notes provides a comparison between the AAMA/WDMA/CSA 101/I.S.2/A and AAMA/WDMA 101/I.S (Reference: Table 25, page 109) Operator Type Awning, hopper, projected window (AP) Basement (BW) Casement (C) Fixed (FW) Class New Gateway 101/I.S.2/A440 Old Gateway 101/I.S.2-97 mm (R) 1200 x " x 16" 48" x 16" (LC) 1200 x " x 32" 48" x 16" (C) 1200 x " x 32" 48" x 16" (HC) 1500 x " x 32" 60" x 32" (AW) 1500 x " x 36" 60" x 36" (R) 800 x " x 14" 32" x 16" (R) 600 x " x 60" 17" x 48" (LC) 800 x " x 60" 24" x 48" (C) 800 x " x 60" 24" x 48" (HC) 900 x " x 60" 24" x 48" (AW) 900 x " x 60" 36" x 60" (R) 1200 x " x 48" 48" x 48" (LC) 1400 x " x 56" 54" x 54" (C) 1500 x " x 60" 60" x 60" (HC) 1500 x " x 71" 72" x 72" 130 Derry Court York, PA phone: fax:

2 Page 2 of 5 Operator Type Dual-action Sidehinged Door (DASHD) Dual-action (DAW) Greenhouse (GH) Hinged Rescue (HE) Horizontally or Vertically Pivoted (HP/VP) Horizontal Slider (HS) Hung (H) Jal-awning (JA) Jalousie (J) Non-hung - vertical sliding Class New Gateway 101/I.S.2/A440 Old Gateway 101/I.S.2-97 mm (R) 900 x " x 79" 32" x 78" (LC) 900 x " x 83" 34" x 80" (C) 1000 x " x 83" 36" x 82" (HC) 1200 x " x 95" 66" x 96" (R) 1100 x " x 60" 44" x 60" (LC) 1200 x " x 60" 48" x 60" (C) 1200 x " x 71" 48" x 72" (HC) 1500 x " x 99" 60" x 96" (R) 900 x 900 x " x 36" 36" x 36" x 12" (R) Varies Varies (R) 1100 x " x 60" 44" x 60" (LC) 1200 x " x 60" 48" x 60" (C) 1200 x " x 87" 48" x 84" (HC) 1500 x " x 99" 60" x 96" (R) 1600 x " x 44" 69" x 48" (LC) 1800 x " x 56" 69" x 56" (C) 1800 x " x 60" 71" x 59" (HC) 2500 x " x 79" 96" x 78" (AW) 2500 x " x 79" 96" x 78" (R) 1000 x " x 63" 44" x 60" (LC) 1100 x " x 75" 44" x 77" (C) 1400 x " x 91" 56" x 90" (HC) 1500 x " x 99" 60" x 96" (R) 1400 x " x 63" 53" x 63" (R) 900 x " x 48" 36" x 48" (R) 1000 x " x 63" 44" x 60" (LC) 1100 x " x 75" N/A (VS) (C) 1400 x " x 91" N/A (R) 900 x " x 79" 30" x 78" Side-hinged Door (SHD) (LC) 900 x " x 83" 34" x 80" (C) 1000 x " x 83" 36" x 82" (HC) 1000 x " x 95" 56" x 96" (AW) 1200 x " x 95" N/A

3 Page 3 of 5 Operator Type Side-hinged (SHW) Sliding Door (SD) Top-hinged (TH) Tropical Awning multiple vent Class New Gateway 101/I.S.2/A440 Old Gateway 101/I.S.2-97 mm (AW) 1200 x " x 71" 48" x 72" (R) 1800 x " x 79" Minimum height x 78" (LC) 2200 x " x 83" Minimum height x 80" (C) 2400 x " x 83" Minimum height x 82" (HC) 3100 x " x 95" Minimum height x 94" (AW) 3100 x " x 95" Minimum height x 94" (C) 1200 x " x 60" 48" x 60" (HC) 1200 x " x 60" 48" x 96" (AW) 1500 x " x 99" 60" x 99" (R) 1200 x " x 63" 48" x 63" (LC) 1400 x " x 99" 53" x 96" (TA) (C) 1400 x " x 99" 53" x 96" (R) 1200 x " x 24" 48" x 24" (LC) 1400 x " x 28" 53" x 26" (TA) (C) 1400 x " x 28" 53" x 26" Addition of Architectural Terrace Door (HC) 1060 x " x 90" (AW) 1200 x " x 96" Tropical Awning single vent Architectural Terrace Door (ATD) Fixed Door (FD) Transom (TR) Side lite (SLT) Unit skylight or roof window glass glazed (SKG/RW) Unit skylight or roof window plastic glazed (SKG/RW) Addition of Fixed Door Classification (R) 900 x " x 79" (LC) 900 x " x 83" (C) 1000 x " x 83" (HC) 1200 x " x 95" (AW) 1500 x " x 99" Addition of Transom Classification (R) 1800 x " x 12" (LC) 1800 x " x 16" (C) 2000 x " x 20" Addition of Side lite Classification (R) 400 x " x 79" (LC) 400 x " x 83" (C) 500 x " x 83" Addition of Skylight/Roof Window Classification (R) 500 x " x 44" (C) 1100 x " x 44" (HC) 1100 x " x 95" (R) 500 x " x 44" (C) 1100 x " x 44" (HC) 1100 x " x 95"

4 Page 4 of 5 General Comments on the new Specification: 1. Test specimens shall be installed per the manufacturer's instructions. All modifications (alterations) made to the test specimen to obtain the reported values shall be described in the report. 2. Ratings may be indicated in SI (metric) or IP. For example, a double hung R class window may be rated as an H-R15 or H-RM 720. If the rating is desired in SI, the design pressure in pascals is preceded by an "M". 3. Any geometric shape must fit within the rectangular gateway size tested. 4. A fixed unit tested in one orientation does not qualify a reversed unit. 5. Drawings are required for reporting but need not be incorporated in the body of the report. 6. Addition of Specialty Products (SP) as an Operator Type. 7. Sealed insulating glass units shall conform to the requirements of ASTM E 774, Level A; CAN/CGSB 12.8; or ASTM E Operating Force (Section 5.3.1, Page 47) 1. Operating products are tested to new ASTM 2068 test method. All operating products are required to pass: 1) Maximum force to maintain positions, and 2) maximum force to open. 2. Latches are required to be tested for latch and unlatch force. 3. Side hinged doors must be tested for the force to close and latch. Air Infiltration (Table 6, Page 52) 1. Air Leakage of composite units does not qualify stand alone individual units. Composite Unit Window or glass door unit consisting of two or more sash or panels within a single frame utilizing an integral mullion. 2. Products may be optionally tested to high performance levels for purpose of code, compliance. 3. Canadian (only) air infiltration/exfiltration testing. Levels are permitted to be reported in the secondary designator. Water Penetration (Table 3, Page 4, Page 38 and Page 53) For U.S. applications, the water penetration resistance test pressure for all products is never more than 580 Pa (12 psf). For Canadian applications, the water penetration resistance test pressure for all products is never more than 720 Pa (15 psf). If a manufacturer supplies an exterior full screen and 1/2 screen; test first with one screen then the other. If interior screens are supplied with the test unit they shall be removed prior to testing. For side-hinged door systems, an allowable exception is to test and rate the products for water penetration resistance at an air pressure differential that ranges from 0 Pa (0.0 psf) to any pressure less than the minimum water penetration resistance test pressure required for the indicated performance class and performance grade (design pressure). Side-hinged door systems tested and rated to this exception have a designation identifying the product for "limited water" (LW) performance. This exception is permitted for side-hinged door systems and is not permitted for any other product type.

5 Page 5 of 5 Uniform Load Deflection (Section , Page 55) 1. Load duration shall be 60 seconds for unit skylights and roof windows and 10 seconds for all other products. It should be noted that some jurisdictions require longer than 10 second load durations for all fenestration products. (i.e. 3600/V = 52 seconds for 70 mph wind zone) 2. Deflection shall be measured at design pressure and reported in millimeters () for all products. There is no maximum allowable deflection for R/LC/C windows. 3. Maximum allowable deflection is L/175 for HC and AW. Uniform Load Structural (Section , Page 55) 1. Test duration shall be 60 seconds for unit skylights and roof windows and 10 seconds for all other products. a. Permanent set limit <0.4%L for R and LC <0.3%L for C and HC <0.2%L for AW 2. Skylights are tested at 200% of Design Pressure. Note: The minimum structural pressures for unit skylight or roof window (glass or plastic glazing) in Table 25, page 114 are incorrect. Reference Page 27, Table 1 Gateway requirements, for the correct minimum structural test pressures. Forced Entry - FER (Section 5.3.5, Page 55) 1. The insect screen shall be removed prior to FER testing. 2. ASTM F842 or ASTM F588 is mandatory. Where local codes require compliance to other FER specifications, this additional testing is optional. (e.g. CAWM 301 and 300) 3. FER tests for swinging doors is mandatory (AAMA 1304). 4. FER tests for skylights is not mandatory. Deglazing Test (Section , Page 57) 1. Maximum movement is limited to 90% of original glazing bite. Side Hinged Doors are required to be tested to Operation/Cycling (Hinged Patio Doors fall under this classification now) (Section , Table 18, Page 73), (Figure 29, Page 107 for qualifying configurations) (R) 25,000 cycles (LC) 100,000 cycles (C) 250,000 cycles (HC) 500,000 cycles (AW) 1,000,000 cycles

6 AAMA Standards Comparison - Windows, Doors & Unit Skylights Revisions & Additional Requirementsas Compared to 1997 Version AAMA/NWWDA 101/I.S.2-97 (Windows and Glass Doors) AAMA/WDMA 101/I.S.2/NAFS-02 (Windows, Glass Doors & Skylights) AAMA/WDMA/CSA 101/I.S.2/A (Windows, Doors & Unit Skylights) Basis of Rating IP Only IP Primary (Metric Optional) IP Primary (Metric Optional) Compliance Measurement Units IP Primary (Metric Secondary) Metric Primary (IP Secondary) Metric Primary (IP Secondary) # of Product Operator Types Operator Type Codes F, DA, HGD & SGD same as 93 F, DA, HGD & SGD same as 93 Chg to FW, FD, DAW, SHD & SD Performance Grade Caps Operating Force (SGD require both forces) No upper limit on Grade (Design Pressure) Upper limit of 60 psf above Gateway except AW Upper limit of 60 psf above Gateway except AW Force to maintain motion ONLY Force to initiate and maintain motion Force to maintain motion but test and record force to initiate Canadian Operating Force Not included Not included Optional Air Leakage 0.3 and 0.1 cfm/ft cfm/ft 2 ONLY 0.3 and 0.1 cfm/ft 2 Canadian Air Leakage Not included Optional Optional Frame/Sash Deflection Limits AW and HC Hung ONLY AW and HC ONLY AW and HC ONLY Glass Deflection Limits Exception Noted Exception Noted Exception Noted Frame/Sash Permanent Set 0.4% (0.2% for AW) 0.4% (0.2% for AW) 0.4% for R & LC, 0.3% for C & HC, 0.2% for AW Forced Entry Resistance Standard ASTM, CMBSO, or AAMA ASTM, CMBSO, or AAMA ASTM ONLY Glass Strength Standard - basis of glass selection ASTM E use weakest glass for testing ASTM E use weakest & thinnest glass for testing ASTM E use weakest glass for testing Plastic Glazing Requirements No Requirements No Requirements Added 6 requirements Materials Referenced Aluminum, Wood and Vinyl Added 5 additional materials Added 8 additional materials Mullion Definitions and Illustrations Definition Only Examples & Illustrations Expanded Explanation Skylights, Sidelites & Transoms Not included Added Added & Expanded Side-Hinged Exterior Doors Not included Not included Added Architectural Terrace Doors Not included Not included Added Limited Water Rating for SHD Not included Not included Added Secondary Designator Not included Not included Added Use of Residential, Light Included Included Deleted Commercial, Commercial, Heavy Commercial and Architectural names in Ratings Cycle/Operating Testing for SHD Not included Not included Added Hardware Water Testing for SHD Not included Not included Added Vertical Load Testing for SHD Not included Not included Added FER Testing for Swinging Doors Not included Not included Added Skylight Testing Orientation Not included Vertical or Sloped Vertical or Sloped Skylights Structural Test Load 1.4 to 3.0 times DP in 1600/I.S x DP, Pos x DP Neg 2.0 x DP, Pos and Neg Skylights Structural Test Duration Not included Neg 10s, Pos 60s Neg & Pos 60s Specimen Structural Damage Same as previous editions Adds actuating mechanisms, disengagements Limits retests due to glass breakage or hardware to two Deglazing Sash Movement < 100% < 90% < 90% Laboratory Test Report Not included - in AAMA Report format & Stamped dwgs Report format & Stamped dwgs Tempered Glass Can be used for testing if it was the weakest, thinnest glass per ASTM E 1300 to qualify other glass types in production. Can be used for testing if it was the weakest, thinnest glass per ASTM E 1300 to qualify other glass types in production. Can be used for testing if it is the weakest per ASTM E 1300 and meets the L/175 requirement for edge deflection, to qualify other glass types in production. Transoms Not included Maximum height is 700 mm Maximum height is 800 mm Reference Standards: AAMA NWWDA I.S AAMA/NWWDA 101/I.S.2-97 AAMA/WDMA 101/I.S.2/NAFS-02 CAN/CSA A440-M00 AAMA/WDMA/CSA 101/I.S.2/A Title Voluntary Specifications for Aluminum and Poly (Vinyl Chloride)(PVC) Prime Windows and Glass Doors Industry Standard for Wood Window Units Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors Voluntary Performance Specification for Windows, Skylights and Glass Doors Windows Standard/Specification for Windows, Doors and Unit Skylights Note: The information included in this table has been provided compliments of AAMA.