Primed Traditional Sliding Patio Doors Premium Wood

Transcription

1 TABLE OF CONTENTS Elevations/Sizes: 1/8 Scale StationaryPanel-WideStile Panel-WideStile Panel-WideStile Panel-WideStile Transoms:1/4 Scale GlazingOptions:3 Scale TrimOptions:3 Scale Standard Mullion Options: 3 Scale LiteCutInformationandOptions Unit Sizing, Rough Openings & Masonry Openings SectionDetails October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-1

2 GENERAL INFORMATION DIMENSIONAL DOORS Wood sliding patio doors may be specified as dimensional, by adjusting the desired rough opening width or height in 1/8 increments from standard. Wood sliding patio doors are available in single, twin, triple and quad panel doors. The standard size range includes sizes specifically designed for replacement of older patio door models in existing structures, as well as a full range of products for architectural consistency. RIGHT STATIONARY OPERATION Wood sliding patio doors are available in a full range of operating and stationary styles. Single panel doors are only available as stationary (non-venting) styles. Two-panel doors are available with left or right operation. Three-panel doors are available with left and right operation and with center or end operators. Four-panel doors are available with two panels operating from the center. Configuration and handing is based on viewing the door from the exterior. MULTIPLE ASSEMBLIES Wood sliding patio doors are available in a wide variety of multiple panel configurations from the factory, all of which are assembled with continuous sills. Mulling of wood sliding patio doors to like products in the field is not recommended. Instead, individual factory assembled units should be installed in contiguous rough openings, in order to provide adequate framing support to assure the best performance of the door systems. October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-2

3 ELEVATION NOTES ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDED TO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THE STRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS. Unit Size Rough Opening Frame Size Daylight Opening 61 27/32 ( 1571 ) 60 ( 1524 ) 59 1/4 ( 1505 ) 21 9/16 ( 547 ) [2] SEE SYMBOL LEGEND BELOW ##* ##** 80 1 ( 2053 ) 80 ( 2032 ) 79 1/2 ( 2019 ) 64 1/8 ( 1629 ) OUTSIDE OF FRAME DAYLIGHT OPENING TWSLDW INDICATES TRADITION PLUS PRIMED SLIDING PATIO DOOR TWSLDW5068 BOOK CODE THE LAST TWO NUMBERS INDICATE THE UNITS HEIGHT THE FIRST TWO NUMBERS INDICATE THE UNIT WIDTH GENERAL SLIDING PATIO DOOR NOTES 1. TRADITION PLUS PRIME SLIDING PATIO DOOR (TWSLDW) UNITS ARE AVAILABLE AS OPERATING OR FIXED UNITS. 2. OPERATING UNITS ARE AVAILABLE AS LEFT OR RIGHT HAND OPERATION. 3. HANDICAP SILL, 10-1/4 BOTTOM RAILS AND INTERMEDIATE LOCK RAILS ARE AVAILABLE FOR ALL UNITS. ELEVATION SYMBOL LEGEND ##* NUMBER INDICATES DESIGN PRESSURE (DP) DP RATING WITH STANDARD GLAZING. OPERATING UNITS UTILIZE MULTI-POINT LOCKING HARDWARE FOR DP RATINGS. ##** NUMBER INDICATES OPTIONAL DESIGN PRESSURE RATING. October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-3

4 STATIONARY PANEL SLIDING PATIO DOORS UNIT SIZE ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 35 15/32 (902) 33 9/16 (852) 32 1(833) 21 9/16 (547) 41 15/32 (1053) 53 15/32 (1358) 39 9/16 (1005) 51 9/16 (1310) 38 1(986) 50 1(1291) 27 9/16 (700) 39 9/16 (1005) 80 1(2053) 80 (2032) 79 1/2 (2019) 64 1/8 (1629) TWSLDW2968 TWSLDW3368 TWSLDW (2459) 96 (2438) 95 1/2 (2426) 80 1/8 (2035) 83 5/16 (2116) 82 1/2 (2063) 82 (2083) 66 (1692) TWSLDW29611 TWSLDW33611 TWSLDW43611 TWSLDW2980 TWSLDW3380 TWSLDW4380 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS SCALE: 1/8 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-4

5 2-PANEL SLIDING PATIO DOORS UNIT SIZE 61 27/32 (1571) 73 27/32 (1876) 97 27/32 (2485) ROUGH OPENING 60 (1524) 72 (1829) 96 (2438) FRAME SIZE 59 1/4 (1505) 71 1/4 (1810) 95 1/4 (2419) DAYLIGHT OPENING 21 9/16 (547)[2] 27 9/16 (700)[2] 39 9/16 (1005)[2] 80 1(2053) 80 (2032) 79 1/2 (2019) 64 1/8 (1629) TWSLDW5068 TWSLDW6068 TWSLDW (2459) 96 (2438) 95 1/2 (2426) 80 1/8 (2035) 83 5/16 (2116) 82 1/2 (2063) 82 (2083) 66 (1692) TWSLDW50611 TWSLDW60611 TWSLDW80611 TWSLDW5080 TWSLDW6080 TWSLDW8080 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT SCALE: 1/8 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-5

6 3-PANEL DOORS WIDE STILE UNIT SIZE ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 94 21/32 (2404) 92 1(2357) 92 1/16 (2338) 21 9/16 (547)[2] 21 9/16 (547) /32 (2709) /32 (3319) 104 1(2662) 128 1(3272) 104 1/16 (2643) 128 1/16 (3253) 27 9/16 (700)[2] 39 9/16 (1005)[2] 21 9/16 (547) 21 9/16 (547) 96 1(2459) 96 (2438) 95 1/2 (2426) 80 1/8 (2035) 83 5/16 (2116) 82 1/2 (2063) 82 (2083) 66 (1692) 80 1(2053) 80 (2032) 79 1/2 (2019) 64 1/8 (1629) TWSLDW5068-1S29 TWSLDW6068-1S29 TWSLDW8068-1S29 TWSLDW S29 TWSLDW S29 TWSLDW S29 TWSLDW5080-1S29 TWSLDW6080-1S29 TWSLDW8080-1S29 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT SCALE: 1/8 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-6

7 3-PANEL DOORS WIDE STILE /32 (2557) 98 1(2510) 98 1/16 (2491) 21 9/16 (547)[2] 27 9/16 (700) UNIT SIZE /32 (2861) /32 (3471) ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 110 1(2815) 110 1/16 (2796) 27 9/16 (700)[2] 27 9/16 (700) 134 1(3424) 134 1/16 (3405) 39 9/16 (1005)[2] 27 9/16 (700) 96 1(2459) 96 (2438) 95 1/2 (2426) 80 1/8 (2035) 83 5/16 (2116) 82 1/2 (2063) 82 (2083) 66 (1692) 80 1(2053) 80 (2032) 79 1/2 (2019) 64 1/8 (1629) TWSLDW5068-1S33 TWSLDW6068-1S33 TWSLDW8068-1S33 TWSLDW S33 TWSLDW S33 TWSLDW S33 TWSLDW5080-1S33 TWSLDW6080-1S33 TWSLDW8080-1S33 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT SCALE: 1/8 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-7

8 3-PANEL DOORS WIDE STILE UNIT SIZE ROUGH OPENING FRAME SIZE DAYLIGHT OPENING /32 (2861) 110 1(2815) 110 1/16 (2796) 21 9/16 (547)[2] 39 9/16 (1005) /32 (3166) /32 (3776) 122 1(3120) 146 1(3729) 122 1/16 (3100) 146 1/16 (3710) 27 9/16 (700)[2] 39 9/16 (1005) 39 9/16 (1005)[2] 39 9/16 (1005) 96 1(2459) 96 (2438) 95 1/2 (2426) 80 1/8 (2035) 83 5/16 (2116) 82 1/2 (2063) 82 (2083) 66 (1692) 80 1(2053) 80 (2032) 79 1/2 (2019) 64 1/8 (1629) TWSLDW5068-1S43 TWSLDW6068-1S43 TWSLDW8068-1S43 TWSLDW S43 TWSLDW S43 TWSLDW S43 TWSLDW5080-1S43 TWSLDW6080-1S43 TWSLDW8080-1S43 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT SCALE: 1/8 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-8

9 4-PANEL DOORS WIDE STILE UNIT SIZE ROUGH OPENING FRAME SIZE DAYLIGHT OPENING /32 (3047) 118 1/8 (3000) 117 3/8 (2981) 21 9/16 (547)[4] /32 (3657) /32 (4876) 142 1/8 (3610) 190 1/8 (4829) 141 3/8 (3591) 189 3/8 (4810) 27 9/16 (700)[4] 39 9/16 (1005)[4] 96 1(2459) 96 (2438) 95 1/2 (2426) 80 1/8 (2035) 83 5/16 (2116) 82 1/2 (2063) 82 (2083) 66 (1692) 80 1(2053) 80 (2032) 79 1/2 (2019) 64 1/8 (1629) TWSLDW10068 TWSLDW12068 TWSLDW16068 TWSLDW TWSLDW TWSLDW TWSLDW10080 TWSLDW12080 TWSLDW16080 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT SCALE: 1/8 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-9

10 TRANSOMS UNIT SIZE ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 35 15/32 (902) 33 9/16 (852) 32 1(833) 21 9/16 (547) 41 15/32 (1053) 39 9/16 (1005) 38 1(986) 27 9/16 (700) 53 15/32 (1358) 51 9/16 (1310) 50 1(1291) 39 9/16 (1005) 18 9/16 (471) 16 3/4 (425) 16 (406) 7 5/16 (186) TCSLDTW2914 TCSLDTW3314 TCSLDTW4314 TCSLDTW2920 TCSLDTW3320 TCSLDTW /16 (979) 36 3/4 (933) 36 (914) 27 5/16 (694) 26 9/16 (674) 24 3/4 (629) 24 (610) 15 5/16 (389) TCSLDTW2930 TCSLDTW3330 TCSLDTW4330 UNIT SIZE ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 61 27/32 (1571) 60 (1524) 59 1/4 (1505) 48 (1219) 73 27/32 (1876) 72 (1829) 71 1/4 (1810) 60 (1524) 97 27/32 (2485) 96 (2438) 95 1/4 (2419) 84 (2134) 18 9/16 (471) 16 3/4 (425) 16 (406) 7 5/16 (186) TCSLDTW5014 TCSLDTW6014 TCSLDTW /16 (674) 24 3/4 (629) 24 (610) 15 5/16 (389) TCSLDTW5020 TCSLDTW6020 TCSLDTW /16 (979) 36 3/4 (933) 36 (914) 27 5/16 (694) TCSLDTW5030 TCSLDTW6030 TCSLDTW8030 ELEVATION SYMBOL LEGEND VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT SCALE: 1/4 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-10

11 GLAZING OPTIONS INTERIOR GLAZED 3/4 1/8 1/8 3/4 1/8 3/4 DS//3/16 DS//DS 5/32//5/32 SCALE: 3 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-11

12 TRIM OPTIONS EXTERIOR TRIM 1 7/32 [31] 1 1/16 [27] 1 7/32 [31] 3 1 [97] 1 31/32 [50] 1 5/16 [33] 31/2 [89] 2 27/32 [72] 4 15/32 [114] BRICKMOULD FLAT CASING 1 X 4 BACKBAND 1 [30] 2 19/32 [66] 31/4 [83] WILLIAMSBURG SCALE: 3 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-12

13 STANDARD MULLION OPTIONS 11 5/16 [287] 3 19/32 [92] 2 5/16 [59] 4 5/16 [110] 11/2 [38] 10 3/32 [256] Patio Door with Sidelite Patio Door with Transom SCALE: 3 = 1 October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-13

14 LITE CUT INFORMATION Wood sliding patio doors are available with removable grilles in 7/8, 1-1/8 and 1-3/8 widths, with grilles between the glass (GBG), or with Simulated Divided Lites. Standard lite cuts are rectangular. LITE CUT OPTIONS Special lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown here represent just a few of the possibilities. Rectangular, horizontal, vertical and Prairie lite patterns are available in all standard size wood sliding patio doors. Uneven, diamond, radius and Gothic lite cuts are available, subject to approval. Approvals are based on the ability to fulfill the design requirement while maintaining the construction integrity of the finished product. RECTANGULAR HORIZONTAL VERTICAL PRAIRIE UNEVEN DIAMOND RADIUS GOTHIC SDL ONLY SDL ONLY SDL ONLY SDL ONLY BAR ALIGNMENT Alignment of divided lite muntin bars from one product to the next is often required by fine architectural design. Wood grilles, GBG S, and Simulated Divided Lites may be specified with muntin bars aligned. October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-14

15 DIRECT SET DIVIDED LITE OPTIONS 3/4 1/4 3/4 1/4 3/4 1/4 3/4 1/4 7/8 7/8 11/8 13/8 11/8 13/ /8 SDL 1 1/8 SDL 1 3/8 SDL 2 5/16 SDL 3/4 3/4 3/4 5/16 GRILLES MEETING NFRC 3mm RULE 11/16 1 GRILLE 23/32 GRILLE 1 GRILLE 11/16 11/16 11/16 11/16 7/8 7/8 11/8 11/8 13/8 13/ /16 2 5/16 7/8 SDL 1 1/8 SDL 1 3/8 SDL 2 5/16 SDL 11/16 11/16 11/16 5/16 11/16 1 GRILLE 23/32 GRILLE 1 GRILLE 7/8 7/8 11/8 11/8 13/8 13/ /16 2 5/16 7/8 SDL 1 1/8 SDL 1 3/8 SDL 2 5/16 SDL 5/16 11/16 1 GRILLE 23/32 GRILLE 1 GRILLE GRILLE PROFILES: X X 1 1/4 X 1/4 X 1 5.5mm X 18mm CONTOUR 8mm X 25mm CONTOUR ALLMETAL XX140 ALLMETAL XX164 ALLMETAL XX140 ALLMETAL XX164 ALLMETAL XX255 ALLMETAL XX380 ALL GLASS AND AIRSPACE DIMENSIONS PER CURRENT CARDINAL GLASS SPECS LITES WITH SHAPES, ANGLES, OR RADII OUTSIDE THE LISEC BENDER CAPABILITIES FOR STAINLESS STEEL WARM EDGE SPACER WILL HAVE ALUMINUM BOX SPACER WITH THE SAME AIRSPACE DIMENSION SHOWN HERE October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-15

16 UNIT SIZING, ROUGH OPENINGS & MASONRY OPENINGS STANDARD OFFERING BRICKMOULD HORIZONTAL FRAME = UNIT SIZE GENERAL NOTES: UNITS WITH NO EXTERIOR TRIM FRAMESIZE=UNITSIZE UNITSIZEISALWAYSTHE EXTREME SIZE OF THE DOOR WITH OR WITHOUT TRIM ROUGHOPENINGISALWAYS3/4 OVER FRAME SIZE OF THE DOOR MASONRY OPENING IS ALWAYS 1/2 OVER THE UNIT SIZE OF THE DOOR VERTICAL FRAME = UNIT SIZE ROUGH OPENING: BRICKMOULD HORIZONTAL 3/8 [10] ROUGH OPENING 3/8 [10] 1 19/64 [33] 2 45/64 [69] 2 61/64 [75] 3 61/64 [100] 3/4 [19] UNIT SIZE FRAME TO EXTERIOR TRIM (UNIT) SIZE 4 [102] 3 [76] 23/4 [70] 1 11/32 [34] HORIZONTAL UNIT SIZE 1 X 4 BACKBAND FRAME + 8 [246] HORIZONTAL UNIT SIZE 31/2 FLATCASING FRAME + 6 [195] HORIZONTAL UNIT SIZE WILLIAMSBURG FRAME + 5 1/2 [148] HORIZONTAL UNIT SIZE BRICKMOULD FRAME+2[67] 4 [102] 3 [76] 23/4 [70] 1 11/32 [34] VERTICAL UNIT SIZE BRICKMOULD FRAME /32 [34] VERTICAL UNIT SIZE WILLIAMSBURG FRAME+23/4 [70] VERTICAL UNIT SIZE 31/2 FLATCASING FRAME + 3 [76] VERTICAL UNIT SIZE 1 X 4 BACKBAND FRAME + 4 [102] VERTICAL ROUGH OPENING October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-16

17 STATIONARY PANEL 1 7/ / /32 4 9/16 1/2 Unit Size Panel Size Glass Size Daylight Opening Frame Size Rough Opening 7 23/32 11/2 5 15/16 VERTICAL SECTION SCALE: NTS October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-17

18 STATIONARY PANEL Rough Opening 3/8 Frame Size 3/8 4 9/16 4 9/ / /32 1 7/32 Daylight Opening 1 7/ /32 Glass Size Panel Size Unit Size 2 11/32 HORIZONTAL SECTION SCALE: NTS October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-18

19 2-PANEL DOOR 11/4 53/4 2 5/16 4 9/16 1/2 1 Unit Size Panel Size Glass Size Daylight Opening Daylight Opening Glass Size Panel Size Frame Size Rough Opening 7 23/ /32 11/2 11/2 5 15/16 VERTICAL SECTION SCALE: NTS October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-19

20 2-PANEL DOOR 3/8 1 Panel Size Glass Size Daylight Opening Rough Opening Frame Size 53/4 4 9/16 Daylight Opening Glass Size Panel Size Unit Size HORIZONTAL SECTION 3/8 4 9/16 2 5/16 53/4 11/4 October 2011 JELD-WEN reserves the right to change specifications without notice. Page /4 SCALE: NTS

21 3-PANEL DOOR 3/8 1 Panel Size 53/4 4 9/16 Glass Size Daylight Opening Rough Opening Frame Size Daylight Opening Glass Size Panel Size Unit Size HORIZONTAL SECTION October 2011 JELD-WEN reserves the right to change specifications without notice. Page /4 SCALE: NTS

22 4-PANEL DOOR 53/4 11/4 3/8 4 9/16 2 5/16 Daylight Opening Glass Size Panel Size Rough Opening Frame Size Unit Size HORIZONTAL SECTION Panel Size Glass Size Daylight Opening SCALE: NTS October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-22

23 TRANSOM 1 7/ /32 21/4 4 9/16 1/2 2 1 Unit Size Panel Size Glass Size Daylight Opening Frame Size Rough Opening / /32 VERTICAL SECTION SCALE: NTS October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-23

24 TRANSOM 3/8 Rough Opening Frame Size 3/8 4 9/16 4 9/ / /32 1 7/32 Daylight Opening Glass Size 2 11/32 Panel Size 2 11/32 Unit Size 1 7/32 HORIZONTAL SECTION SCALE: NTS October 2011 JELD-WEN reserves the right to change specifications without notice. Page 20-24