Siteline EX Clad Casement Windows Premium Wood

Transcription

1 TABLE OF CONTENTS Specifications QuickSpecGuide Elevations:1/4 Scale Casement CasementPicture CasementPicturewithFlankers CasementSectorTop SashGlazingOptions:3 Scale TrimOptions:3 Scale JambOptions:3 Scale Standard Mullion Options LiteCutInformation ClearOpeningandDaylightSpecifications Unit Sizing, Rough Openings & Masonry Openings SectionDetails:6 Scale Bay & Bow Specifications and Rough Opening Information SectionDetails:3 Scale(Bay&Bow) October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-1

2 EXTERIOR FINISH Exterior aluminum surfaces are low maintenance extruded aluminum coated with a thermo set polyester finish that meets or exceeds the AAMA 2603 performance standards. Standard colors include Brilliant White, Chestnut Bronze, Desert Sand, French Vanilla, Hartford Green, Mesa Red, Black, Arctic Silver and Dark Chocolate. AURALAST R WOOD AuraLast R wood is fundamentally different from wood resulting from traditional millwork preservation processes in that it uses a proprietary vacuum/pressure process to provide protection throughout the wood parts used to make windows and doors. AuraLast R wood is distinguished from wood using the current preservation methods by its unique ability to achieve greater penetration of the active ingredients into the wood parts, with a penetration of the treatment being a minimum of 92%. INTERIOR FINISH All interior surfaces are unfinished clear pine ready for on site finishing. Primed and pre-finished interiors are available in paint: Pure White, Extra White, Natural Choice, Moderate White; in stain: Wheat, Cherry, Cordovan; and Clear Lacquer. FRAME Frame is assembled from select kiln dried pine using AuraLast R wood on all exterior parts. Exterior surface is covered with.050 (1.27mm) extruded aluminum cladding; corner joints are mechanically fastened over a silicone injected nylon corner key. Frame thickness is 1-5/32 (29.4mm) at head, side jamb and at sill. Basic jamb width is 2- (63.5mm). Standard jamb width is 4-9/16 (116mm). Integral nailing fin is part of extrusion on all four sides. Assembled frame includes all weather-stripping and hardware installed. Exterior of frame extrusion is grooved to accept accessories. SASH Sash is 1-7/16 (36.5mm) thick and combines an extruded aluminum exterior with select kiln-dried pine using AuraLast R wood. Joints are mortise and tenoned, machine clamped for squareness and secured with metal fasteners. Exterior surfaces are covered with.045 (1.2mm) extruded aluminum. GLAZING 3/4 (19mm) thick sealed insulating glass is constructed from two panes of glass, utilizing a continuous roll formed stainless steel spacer with dual seal sealant. The glass is mounted into the sash using a silicone-glazing compound and secured with interior applied profiled wood stops. All insulating glass units comply with the performance requirements of IGCC in accordance with either ASTM E774 or E2190. GLAZING OPTIONS Siteline EX Clad Casement Windows 3/4 insulating glass available in Low-E with Argon, Low-E, Low-E 366, Clear, Neat Glass, reflective, tinted, or obscure, tempered or other specialty glass as specified. Preserve film is a thick polyethylene film with a low tack acrylic adhesive applied to the glass for protection during shipping and installation. 4,000 foot elevations and higher require a capillary tube to equalize environmental stress (otherwise known as High Altitude glazing). High Altitude glazing does not allow the use of Argon as listed under glazing options. PRODUCT SPECIFICATIONS WEATHER-STRIPPING Engineered system combines a flexible, lined weather-strip applied to the full perimeter of the sash and thermoplastic rubber bulb applied to the full perimeter of the frame. HARDWARE Sash pivot on concealed hinges with sliding steel reinforced nylon shoes in an integral frame track. Stainless steel concealed locking system is standard, and the window locks sequentially. EntryGard dual arm retro operator has removable polycarbonate cover, die cast zinc bash and hardened steel worm gears and arms. Hinges and retro operator arms feature stainless steel. The die cast locking lever is located on the side jamb at the lower corner of the window opposite the operator and has a molded bezel cover that snaps over the rout on the side stop. Units under 20 wide will feature a dyad operator. Color choices for locks and operator covers are White, Chestnut Bronze, Desert Sand or optional Bright Brass, Antique Brass, Polished Brass, Brushed Chrome or Imitation Oil Rubbed Bronze. INSECT SCREENS Charcoal fiberglass screen cloth (18x16 mesh) set in painted roll formed aluminum frame fitted to the inside of the window with all necessary hardware, in White, Chestnut Bronze, Desert Sand or optional Bright Brass, Antique Brass, Polished Brass, Brushed Chrome or Imitation Oil Rubbed Bronze. Aluminum mesh and Phantom screens are also available. Insect screens are intended to allow air and light in and to keep insects out. They are not intended to keep anyone or anything from falling through an open window. For safety screens or other security devices contact your local building supply retailer. GRILLES SDL (Simulated Divided Lites) - extruded aluminum muntins permanently applied to the exterior of the insulating glass unit (not available on textured glass) in 7/8 (22mm), 1-1/8 (28.5mm), or 1-3/8 (34.9mm) widths. SDL is standard with a light bronze internal shadow bar to give a true divided lite appearance. As an option, SDL may be ordered with a silver shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Also available is a 2-5/16 (59mm) SDL bar, which simulates a double-hung checkrail. Full Surround Wood Grilles - Rectangular unfinished clear pine wood grilles in 7/8 (22mm) are available in patterns selected by the owner. GBG (Grilles between the Glass) - 5/8 (15.9mm) flat and 23/32 or 1 contour mounted between the glass panes suspended within the air cavity. EXTERIOR TRIM 1-5/8 (41mm) wide aluminum brickmould or Adams casing with an integral nailing fin is available factory applied. Also available is 3- (88.5mm) flat casing with an integral nailing fin. All of the accessories are.050 (1.3mm) extruded aluminum. Two sizes of frame expander, 1-7/8 (48mm) and 3-1/4 (83mm) may be used alone or in conjunction with a 2-1/8 (54mm) mull expander. Standard 5/16 (8mm) clad mull cover used for joining windows together. Windows may also be joined with 1 (25.4mm), 2 (51mm), or 4 (102mm) mull covers. Color and finish match exterior finish specs above. Continued on next page October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-2

3 EXTENSION JAMBS Extension jambs are factory applied to the interior on all four sides of the frame and are 4/4 standard thick pine to accommodate wall depths up to 7-1/4 with one piece, and up to 12 with two pieces. 9/16 (14.2mm) and 5/4 option or 5/4-4/4 stacked option also available. INSTALLATION Siteline EX Clad Casement Windows Installation per JELD-WEN Installation Method for Metal Clad Windows JII002 or JII013. See for instructions. PRODUCT SPECIFICATIONS PERFORMANCE NFRC Certified - (Rated and labeled in accordance with NFRC) WDMA Hallmark Certified - In accordance with AAMA/NWWDA/101/I.S.2-97 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-3

4 SPECIFICATION EXTERIOR FINISH S Brilliant White S Chestnut Bronze S Desert Sand S French Vanilla S Mesa Red EXTERIOR TRIM S Nailing Fin S Drip Cap STANDARD FEATURES QUICK SPEC GUIDE S S S S Hartford Green Black Arctic Silver Dark Chocolate INTERIOR FINISH S Natural S Priming Available SIZE S Width: Operators and Stationary Casements 18, 20, 24, 28, 30, 36 Casement Fixed Units 42, 48, 54, 60, 66, 72 S Height: Operators, Stationary Casements and Casement Fixed Units 12, 18, 20, 24, 28, 30, 36, 42, 48, 54, 60, 66, 72, 78, 84 S For RO, add 3/4 GLAZING S Low-E Insulating Glass S Preserve Protective Film OPTIONAL FEATURES Some options may require additional lead times. Consult your JELD-WEN Sales Representative. S Aluminum 1-5/8 Brickmould with integral nailing fin S Adams or 3- Flat Casing with integral nailing fin Pre-finished Interior Options are: S Paint - Pure White, Extra White, Natural Choice, Moderate White S Stain - Wheat, Fruitwood, Cherry, Cordovan S Clear Lacquer S Operator: Any width: 14-1/4 to 36 S Stationary & Fixed Units: Any Width: 12 to 72 S Operator, Stationary & Fixed Units: Any Height: 12 to 84 Operating Units: 14 to 84 S 36 x 78, and 28, 30, 36 x 84 not available as operating S For RO, add 3/4 S Clear S Obscure S Bronze S Low-E 366 S High Altitude S S S Neat Glass Reflective Tempered GRILLES S 5/8 Flat, 23/32 or 1 Contour GBG S 7/8 Full Surround Wood Grilles SDL Bead Profile: S 7/8, 1-1/8, 1-3/8, 2-5/16 with Light Bronze Shadow Bar S 7/8, 1-1/8, 1-3/8, 2-5/16 with Silver Shadow Bar HARDWARE S Standard Folding Nesting Handle S Concealed Locking System HARDWARE COLOR S White S Desert Sand S Chestnut Bronze Siteline EX Clad Casement Windows S T-Handle S Round Knob S S S Antique Brass Polished Brass Brushed Chrome S Imitation Oil Rubbed Bronze Continued on next page October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-4

5 QUICK SPEC GUIDE SPECIFICATION STANDARD FEATURES OPTIONAL FEATURES Some options may require additional lead times. Consult your JELD-WEN Sales Representative. JAMB S 4-9/16 S Minimum: 2- S Maximum: 7-1/4 (one piece) S Maximum: 12 (two piece) SCREENS S Fiberglass S Aluminum Mesh available S Phantom Screen - some size limitations apply SCREEN FRAME COLOR S Brilliant White S Desert Sand S Chestnut Bronze October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-5

6 GENERAL INFORMATION CASEMENT DIMENSIONAL WINDOWS Clad casement windows may be specified as dimensional, by adjusting the desired rough opening width or height in 1/4 increments from standard. Clad casement windows are available with left or right hand operation, or stationary (non-venting). Operating mechanism includes corrosion resistant steel hinges and dual arm roto-type operator with hardened steel gears and operating arms. Sash locks are concealed unison type with an exposed locking lever and escutcheon plate. There are several interior hardware finish options. Refer to the Specifications for finish options. MULTIPLE ASSEMBLIES Clad casement windows may be mulled above, below, or beside other clad casement windows, or other clad window products. Factory assembled mulls are limited in height (100 ), width (150 ), and a total area (75 square feet). October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-6

7 HANDING & OPERATION CASEMENT LEFT HAND RIGHT HAND OPERATOR OPERATOR CASEMENT UNIT HANDING: UNIT HANDING IS DEFINED (FROM THE EXTERIOR) AS THE DIRECTION THE SASH OPENS. October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-7

8 ELEVATION NOTES CASEMENT ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDED TO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THE STRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 21 (546) 24 (645) 18 3/4 (476) 18 (457) 12 3/32 (307) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include sillnose. (Subtract from Masonry Opening for Unit Size) 20 5/16 (515) 21 13/16 (554) 18 3/4 (476) 18 (457) 12 3/32 (307) OUTSIDE OF FRAME DAYLIGHT OPENING ECC1818 ECC INDICATES SITELINE EX CLAD CASEMENT THE FIRST TWO NUMBERS INDICATE THE UNIT WIDTH BOOK CODE THE LAST TWO NUMBERS INDICATE THE UNIT HEIGHT GENERAL CASEMENT NOTES ELEVATION SYMBOL LEGEND: 1. SITELINE EX CLAD CASEMENT (ECC) UNITS ARE AVAILABLE AS OPERATING OR STATIONARY UNITS. 2. ECCP IN A BOOK CODE DENOTES THE UNIT IS A CLAD CASEMENT PICTURE (STATIONARY) UNIT. 3. UNIT ELEVATIONS ARE SHOWN WITHOUT EXTERIOR TRIM. UNIT SIZES & MASONRY OPENING DIMENSIONS WILL CHANGE WITH THE ADDITION OF EXTERIOR TRIM. SEE THE UNIT SIZING, ROUGH OPENINGS & MASONRY OPENINGS PAGE FOR EXTERIOR TRIM EFFECTS. 4. OPERATING UNITS ARE AVAILABLE AS LEFT OR RIGHT HAND OPERATION. 5. DIMENSIONAL VALUES IN PARENTHESES ARE MILLIMETER CONVERSIONS. M.O. MASONRY OPENING October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-8

9 1-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 21 (546) 24 (645) 18 3/4 (476) 18 (457) 12 3/32 (307) 23 (597) 27 (699) 31 (800) 33 (851) 39 (1003) 26 (673) 30 (775) 34 (876) 36 (927) 42 (1054) 20 3/4 (527) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 36 3/4 (933) 20 (508) 24 (610) 28 (711) 30 (762) 36 (914) 14 3/32 (358) 18 3/32 (460) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) S S S S S S ECC1812 ECC2012 ECC2412 ECC2812 ECC3012 ECC /4 (476) 18 (457) ECC1818 ECC2018 ECC2418 ECC2818 ECC3018 ECC /4 (527) 20 (508) ECC1820 ECC2020 ECC2420 ECC2820 ECC3020 ECC /4 (933) 36 (914) 48 3/4 (1238) 48 (1219) 30 3/4 (781) 30 (762) 24 3/4 (629) 24 (610) ECC1824 ECC2024 ECC2424 ECC2824 ECC3024 ECC /16 (770) 31 13/16 (808) 28 3/4 (730) 28 (711) 22 3/32 (561) 26 5/16 (668) 27 13/16 (706) 20 5/16 (515) 21 13/16 (554) 12 3/32 (307) 22 5/16 (578) 23 13/16 (605) 14 3/32 (358) 18 3/32 (460) ECC1828 ECC2028 ECC2428 ECC2828 ECC3028 ECC /16 (821) 33 13/16 (859) 24 3/32 (612) ECC1830 ECC2030 ECC2430 ECC2830 ECC3030 ECC /4 (1086) 42 (1067) 38 5/16 (973) 39 13/16 (1011) 30 3/32 (764) E ECC1836 ECC2036 ECC2436 ECC2836 ECC3036 ECC /16 (1126) 45 13/16 (1164) 36 3/32 (917) E E ECC1842 ECC2042 ECC2442 ECC2842 ECC3042 ECC /16 (1278) 51 13/16 (1316) 42 3/32 (1070) E E E ECC1848 ECC2048 ECC2448 ECC2848 ECC3048 ECC3648 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS E BASIC UNIT CLEAR OPENING EXCEEDS 20 IN WIDTH, 24 IN HEIGHT & A MINIMUM OF 5.7 SQ. FT. S AVAILABLE AS STATIONARY ONLY. Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-9

10 1-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 21 (546) 24 (645) 18 3/4 (476) 18 (457) 12 3/32 (307) 23 (597) 27 (699) 31 (800) 33 (851) 39 (1003) 26 (673) 30 (775) 34 (876) 36 (927) 42 (1054) 20 3/4 (527) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 36 3/4 (933) 20 (508) 24 (610) 28 (711) 30 (762) 36 (914) 14 3/32 (358) 18 3/32 (460) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 78 3/4 (2000) 78 (1981) 72 3/4 (1848) 72 (1829) 66 3/4 (1695) 66 (1676) 60 3/4 (1543) 60 (1524) 56 5/16 (1430) 57 13/16 (1468) 54 3/4 (1391) 54 (1372) 48 3/32 (1222) E E E ECC1854 ECC2054 ECC2454 ECC2854 ECC3054 ECC /16 (1583) 63 13/16 (1621) 54 3/32 (1374) E E E ECC1860 ECC2060 ECC2460 ECC2860 ECC3060 ECC /16 (1735) 69 13/16 (1773) 60 3/32 (1526) E E E ECC1866 ECC2066 ECC2466 ECC2866 ECC3066 ECC /16 (1888) 75 13/16 (1926) 66 3/32 (1679) E E E ECC1872 ECC2072 ECC2472 ECC2872 ECC3072 ECC /16 (2040) 81 13/16 (2078) 72 3/32 (1831) E E S ECC1878 ECC2078 ECC2478 ECC2878 ECC3078 ECC3678 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS E BASIC UNIT CLEAR OPENING EXCEEDS 20 IN WIDTH, 24 IN HEIGHT & A MINIMUM OF 5.7 SQ. FT. S AVAILABLE AS STATIONARY ONLY. Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-10

11 1-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 21 (546) 24 (645) 18 3/4 (476) 18 (457) 12 3/32 (307) 23 (597) 27 (699) 31 (800) 33 (851) 39 (1003) 26 (673) 30 (775) 34 (876) 36 (927) 42 (1054) 20 3/4 (527) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 36 3/4 (933) 20 (508) 24 (610) 28 (711) 30 (762) 36 (914) 14 3/32 (358) 18 3/32 (460) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 86 5/16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) S S S ECC1884 ECC2084 ECC2484 ECC2884 ECC3084 ECC3684 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS S AVAILABLE AS STATIONARY ONLY. Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-11

12 2-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 39 (1003) 42 (1054) 36 3/4 (933) 36 (914) 12 3/32 (307)[2] 43 (1105) 51 (1308) 59 (1511) 63 (1613) 75 (1918) 46 (1181) 54 (1384) 62 (1588) 66 (1689) 78 (1994) 40 3/4 (1035) 48 3/4 (1238) 56 3/4 (1441) 60 3/4 (1543) 72 3/4 (1848) 40 (1016) 48 (1219) 56 (1422) 60 (1524) 72 (1829) 14 3/32 (358)[2] 18 3/32 (460)[2] 22 3/32 (561)[2] 24 3/32 (612)[2] 30 3/32 (764)[2] ECC ECC ECC ECC ECC ECC /4 (476) 18 (457) ECC ECC ECC ECC ECC ECC /4 (527) 20 (508) 24 3/4 (629) 24 (610) 30 3/4 (781) 30 (762) 36 3/4 (933) 36 (914) 42 3/4 (1086) 42 (1067) 48 3/4 (1238) 48 (1219) ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /4 (1391) 54 (1372) ECC ECC ECC ECC ECC ECC /4 (1543) 60 (1524) ECC ECC ECC ECC ECC ECC /4 (1695) 66 (1676) 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) 20 5/16 (515) 21 13/16 (554) 12 3/32 (307) 22 5/16 (578) 23 13/16 (605) 26 5/16 (668) 27 13/16 (706) 30 5/16 (770) 31 13/16 (808) 32 5/16 (821) 33 13/16 (859) 38 5/16 (973) 39 13/16 (1011) 44 5/16 (1126) 45 13/16 (1164) 50 5/16 (1278) 51 13/16 (1316) 28 3/4 (730) 28 (711) 14 3/32 (358) 18 3/32 (460) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 36 3/32 (917) 42 3/32 (1070) 68 5/16 (1735) 69 13/16 (1773) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) ECC ECC ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-12

13 2-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 39 (1003) 42 (1054) 36 3/4 (933) 36 (914) 12 3/32 (307)[2] 43 (1105) 51 (1308) 59 (1511) 63 (1613) 75 (1918) 46 (1181) 54 (1384) 62 (1588) 66 (1689) 78 (1994) 40 3/4 (1035) 48 3/4 (1238) 56 3/4 (1441) 60 3/4 (1543) 72 3/4 (1848) 40 (1016) 48 (1219) 56 (1422) 60 (1524) 72 (1829) 14 3/32 (358)[2] 18 3/32 (460)[2] 22 3/32 (561)[2] 24 3/32 (612)[2] 30 3/32 (764)[2] 72 3/4 (1848) 72 (1829) ECC ECC ECC ECC ECC ECC /16 (2040) 81 13/16 (2078) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 74 5/16 (1888) 75 13/16 (1926) 66 3/32 (1679) ECC ECC ECC ECC ECC ECC /16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) ECC ECC ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-13

14 3-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 57 (1448) 60 (1537) 54 3/4 (1391) 54 (1372) 12 3/32 (307)[3] 63 (1613) 75 (1918) 87 (2223) 93 (2380) 111 (2832) 66 (1689) 78 (1994) 90 (2299) 96 (2451) 114 (2908) 60 3/4 (1543) 72 3/4 (1848) 84 3/4 (2153) 90 3/4 (2305) 108 3/4 (2762) 60 (1524) 72 (1829) 84 (2134) 90 (2286) 108 (2743) 14 3/32 (358)[3] 18 3/32 (460)[3] 22 3/32 (561)[3] 24 3/32 (612)[3] 30 3/32 (764)[3] 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) ECC ECC ECC ECC ECC ECC /16 (515) 21 13/16 (554) 22 5/16 (578) 23 13/16 (605) 18 3/4 (476) 18 (457) 20 3/4 (527) 20 (508) 12 3/32 (307) ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /4 (629) 24 (610) 30 3/4 (781) 30 (762) 36 3/4 (933) 36 (914) 42 3/4 (1086) 42 (1067) 48 3/4 (1238) 48 (1219) ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /4 (1391) 54 (1372) ECC ECC ECC ECC ECC ECC /4 (1543) 60 (1524) ECC ECC ECC ECC ECC ECC /4 (1695) 66 (1676) 14 3/32 (358) 26 5/16 (668) 27 13/16 (706) 30 5/16 (770) 31 13/16 (808) 32 5/16 (821) 33 13/16 (859) 38 5/16 (973) 39 13/16 (1011) 44 5/16 (1126) 45 13/16 (1164) 50 5/16 (1278) 51 13/16 (1316) 28 3/4 (730) 28 (711) 18 3/32 (460) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 36 3/32 (917) 42 3/32 (1070) 68 5/16 (1735) 69 13/16 (1773) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) ECC ECC ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-14

15 3-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 57 (1448) 60 (1537) 54 3/4 (1391) 54 (1372) 12 3/32 (307)[3] 63 (1613) 75 (1918) 87 (2223) 93 (2380) 111 (2832) 66 (1689) 78 (1994) 90 (2299) 96 (2451) 114 (2908) 60 3/4 (1543) 72 3/4 (1848) 84 3/4 (2153) 90 3/4 (2305) 108 3/4 (2762) 60 (1524) 72 (1829) 84 (2134) 90 (2286) 108 (2743) 14 3/32 (358)[3] 18 3/32 (460)[3] 22 3/32 (561)[3] 24 3/32 (612)[3] 30 3/32 (764)[3] 72 3/4 (1848) 72 (1829) ECC ECC ECC ECC ECC ECC /16 (2040) 81 13/16 (2078) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 74 5/16 (1888) 75 13/16 (1926) 66 3/32 (1679) ECC ECC ECC ECC ECC ECC /16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) ECC ECC ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-15

16 M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 75 (1918) 78 (1994) 72 3/4 (1848) 72 (1829) 12 3/32 (307)[4] Siteline EX Clad Casement Windows 4-WIDE UNITS 83 (2121) 99 (2527) 115 (2934) 123 (3137) 86 (2197) 102 (2604) 118 (3010) 126 (3213) 80 3/4 (2051) 96 3/4 (1238) 112 3/4 (1441) 120 3/4 (3067) 80 (2032) 96 (2457) 112 (2864) 120 (3048) 14 3/32 (358)[4] 18 3/32 (460)[4] 22 3/32 (561)[4] 24 3/32 (612)[4] 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) ECC ECC ECC ECC ECC /16 (515) 21 13/16 (554) 18 3/4 (476) 18 (457) 12 3/32 (307) ECC ECC ECC ECC ECC /16 (578) 23 13/16 (605) 20 3/4 (527) 20 (508) 14 3/32 (358) ECC ECC ECC ECC ECC /16 (668) 27 13/16 (706) 24 3/4 (629) 24 (610) 18 3/32 (460) ECC ECC ECC ECC ECC /16 (770) 31 13/16 (808) 30 3/4 (781) 30 (762) 36 3/4 (933) 36 (914) ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /4 (1086) 42 (1067) ECC ECC ECC ECC ECC /4 (1238) 48 (1219) ECC ECC ECC ECC ECC /4 (1391) 54 (1372) ECC ECC ECC ECC ECC /4 (1543) 60 (1524) ECC ECC ECC ECC ECC /4 (1695) 66 (1676) 32 5/16 (821) 33 13/16 (859) 38 5/16 (973) 39 13/16 (1011) 28 3/4 (730) 28 (711) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 44 5/16 (1126) 45 13/16 (1164) 36 3/32 (917) 50 5/16 (1278) 51 13/16 (1316) 42 3/32 (1070) 68 5/16 (1735) 69 13/16 (1773) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) ECC ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-16

17 4-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 75 (1918) 78 (1994) 72 3/4 (1848) 72 (1829) 12 3/32 (307)[4] 83 (2121) 99 (2527) 115 (2934) 123 (3137) 86 (2197) 102 (2604) 118 (3010) 126 (3213) 80 3/4 (2051) 96 3/4 (1238) 112 3/4 (1441) 120 3/4 (3067) 80 (2032) 96 (2457) 112 (2864) 120 (3048) 14 3/32 (358)[4] 18 3/32 (460)[4] 22 3/32 (561)[4] 24 3/32 (612)[4] ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) 80 5/16 (2040) 81 13/16 (2078) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 66 3/32 (1679) ECC ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-17

18 4-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 147 (3747) 150 (3823) 144 3/4 (3677) 144 (3658) 30 3/32 (764)[4] M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 147 (3747) 150 (3823) 144 3/4 (3677) 144 (3658) 30 3/32 (764)[4] 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) 20 5/16 (515) 21 13/16 (554) 18 3/4 (476) 18 (457) ECC ECC ECC /4 (527) 20 (508) 24 3/4 (629) 24 (610) ECC ECC ECC /4 (781) 30 (762) ECC ECC ECC /4 (933) 36 (914) ECC /4 (1086) 42 (1067) ECC /4 (1238) 48 (1219) ECC /4 (1391) 54 (1372) ECC /4 (1543) 60 (1524) ECC /4 (1695) 66 (1676) 12 3/32 (307) 22 5/16 (578) 23 13/16 (605) 26 5/16 (668) 27 13/16 (706) 14 3/32 (358) 18 3/32 (460) 30 5/16 (770) 31 13/16 (808) 32 5/16 (821) 33 13/16 (859) 28 3/4 (730) 28 (711) 22 3/32 (561) 24 3/32 (612) 38 5/16 (973) 39 13/16 (1011) 30 3/32 (764) 68 5/16 (1735) 69 13/16 (1773) 44 5/16 (1126) 45 13/16 (1164) 60 3/32 (1526) 36 3/32 (917) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) 50 5/16 (1278) 51 13/16 (1316) 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 66 3/32 (1679) 80 5/16 (2040) 81 13/16 (2078) 42 3/32 (1070) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 86 5/16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose,seeTrim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-18

19 5-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 93 (2380) 96 (2451) 90 3/4 (2305) 90 (2286) 12 3/32 (307)[5] 103 (2629) 123 (3137) 143 (3645) 106 (2705) 126 (3213) 146 (3721) 100 3/4 (2559) 120 3/4 (3067) 140 3/4 (3575) 100 (2540) 120 (3048) 140 (3556) 14 3/32 (358)[5] 18 3/32 (460)[5] 22 3/32 (561)[5] 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) ECC ECC ECC ECC /16 (515) 21 13/16 (554) 18 3/4 (476) 18 (457) 12 3/32 (307) ECC ECC ECC ECC /16 (578) 23 13/16 (605) 20 3/4 (527) 20 (508) 14 3/32 (358) ECC ECC ECC ECC /4 (629) 24 (610) ECC ECC ECC ECC /4 (781) 30 (762) 36 3/4 (933) 36 (914) 42 3/4 (1086) 42 (1067) 48 3/4 (1238) 48 (1219) ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /4 (1391) 54 (1372) ECC ECC ECC ECC /4 (1543) 60 (1524) ECC ECC ECC ECC /4 (1695) 66 (1676) 26 5/16 (668) 27 13/16 (706) 18 3/32 (460) 30 5/16 (770) 31 13/16 (808) 32 5/16 (821) 33 13/16 (859) 38 5/16 (973) 39 13/16 (1011) 44 5/16 (1126) 45 13/16 (1164) 50 5/16 (1278) 51 13/16 (1316) 28 3/4 (730) 28 (711) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 36 3/32 (917) 42 3/32 (1070) 68 5/16 (1735) 69 13/16 (1773) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-19

20 5-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 93 (2380) 96 (2451) 90 3/4 (2305) 90 (2286) 12 3/32 (307)[5] 103 (2629) 123 (3137) 143 (3645) 106 (2705) 126 (3213) 146 (3721) 100 3/4 (2559) 120 3/4 (3067) 140 3/4 (3575) 100 (2540) 120 (3048) 140 (3556) 14 3/32 (358)[5] 18 3/32 (460)[5] 22 3/32 (561)[5] ECC ECC ECC ECC ECC ECC ECC ECC /16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) 80 5/16 (2040) 81 13/16 (2078) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 66 3/32 (1679) ECC ECC ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-20

21 5-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 153 (3899) 183 (4661) 156 (3975) 186 (4737) 150 3/4 (3829) 180 3/4 (4591) 150 (3810) 180 (4572) 24 3/32 (612)[5] 30 3/32 (764)[5] 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) ECC ECC /16 (515) 21 13/16 (554) 18 3/4 (476) 18 (457) 12 3/32 (307) ECC ECC /16 (578) 23 13/16 (605) 20 3/4 (527) 20 (508) 24 3/4 (629) 24 (610) ECC ECC ECC ECC /4 (781) 30 (762) 36 3/4 (933) 36 (914) 42 3/4 (1086) 42 (1067) 48 3/4 (1238) 48 (1219) ECC ECC ECC ECC ECC ECC ECC ECC ECC ECC /4 (1391) 54 (1372) ECC ECC /4 (1543) 60 (1524) ECC ECC /4 (1695) 66 (1676) 26 5/16 (668) 27 13/16 (706) 14 3/32 (358) 18 3/32 (460) 30 5/16 (770) 31 13/16 (808) 32 5/16 (821) 33 13/16 (859) 38 5/16 (973) 39 13/16 (1011) 44 5/16 (1126) 45 13/16 (1164) 50 5/16 (1278) 51 13/16 (1316) 28 3/4 (730) 28 (711) 22 3/32 (561) 24 3/32 (612) 30 3/32 (764) 36 3/32 (917) 42 3/32 (1070) 68 5/16 (1735) 69 13/16 (1773) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-21

22 5-WIDE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 153 (3899) 183 (4661) 156 (3975) 186 (4737) 150 3/4 (3829) 180 3/4 (4591) 150 (3810) 180 (4572) 24 3/32 (612)[5] 30 3/32 (764)[5] ECC ECC ECC ECC /16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) 80 5/16 (2040) 81 13/16 (2078) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 74 5/16 (1888) 75 13/16 (1926) 72 3/4 (1848) 72 (1829) 66 3/32 (1679) ECC ECC ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-22

23 PICTURE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 45 (1156) 51 (1308) 57 (1448) 63 (1613) 48 (1232) 54 (1384) 60 (1537) 66 (1689) 42 3/4 (1086) 48 3/4 (1238) 54 3/4 (1391) 60 3/4 (1543) 42 (1067) 48 (1219) 54 (1372) 60 (1524) 36 3/32 (917) 42 3/32 (1070) 48 3/32 (1222) 54 3/32 (1374) 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) 18 3/4 (476) 18 (457) 20 3/4 (527) 20 (508) ECCP4212 ECCP4812 ECCP5412 ECCP6012 ECCP4218 ECCP4818 ECCP5418 ECCP6018 ECCP4220 ECCP4820 ECCP5420 ECCP /4 (1238) 48 (1219) 42 3/4 (1086) 42 (1067) 36 3/4 (933) 36 (914) 30 3/4 (781) 30 (762) 24 3/4 (629) 24 (610) ECCP4224 ECCP4824 ECCP5424 ECCP /16 (770) 31 13/16 (808) 28 3/4 (730) 28 (711) 22 3/32 (561) 26 5/16 (668) 27 13/16 (706) 20 5/16 (515) 21 13/16 (554) 22 5/16 (578) 23 13/16 (605) 12 3/32 (307) 14 3/32 (358) 18 3/32 (460) ECCP4228 ECCP4828 ECCP5428 ECCP /16 (821) 33 13/16 (859) 24 3/32 (612) ECCP4230 ECCP4830 ECCP5430 ECCP /16 (973) 39 13/16 (1011) 30 3/32 (764) ECCP4236 ECCP4836 ECCP5436 ECCP /16 (1126) 45 13/16 (1164) 36 3/32 (917) ECCP4242 ECCP4842 ECCP5442 ECCP /16 (1278) 51 13/16 (1316) 42 3/32 (1070) ECCP4248 ECCP4848 ECCP5448 ECCP6048 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-23

24 PICTURE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 45 (1156) 51 (1308) 57 (1448) 63 (1613) 48 (1232) 54 (1384) 60 (1537) 66 (1689) 42 3/4 (1086) 48 3/4 (1238) 54 3/4 (1391) 60 3/4 (1543) 42 (1067) 48 (1219) 54 (1372) 60 (1524) 36 3/32 (917) 42 3/32 (1070) 48 3/32 (1222) 54 3/32 (1374) 78 3/4 (2000) 78 (1981) 72 3/4 (1848) 72 (1829) 66 3/4 (1695) 66 (1676) 60 3/4 (1543) 60 (1524) 56 5/16 (1430) 57 13/16 (1468) 54 3/4 (1391) 54 (1372) 48 3/32 (1222) ECCP4254 ECCP4854 ECCP5454 ECCP /16 (1583) 63 13/16 (1621) 54 3/32 (1374) ECCP4260 ECCP4860 ECCP5460 ECCP /16 (1735) 69 13/16 (1773) 60 3/32 (1526) ECCP4266 ECCP4866 ECCP5466 ECCP /16 (1888) 75 13/16 (1926) 66 3/32 (1679) ECCP4272 ECCP4872 ECCP5472 ECCP /16 (2040) 81 13/16 (2078) 72 3/32 (1831) ECCP4278 ECCP4878 ECCP5478 ECCP6078 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-24

25 PICTURE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 45 (1156) 51 (1308) 57 (1448) 63 (1613) 48 (1232) 54 (1384) 60 (1537) 66 (1689) 42 3/4 (1086) 48 3/4 (1238) 54 3/4 (1391) 60 3/4 (1543) 42 (1067) 48 (1219) 54 (1372) 60 (1524) 36 3/32 (917) 42 3/32 (1070) 48 3/32 (1222) 54 3/32 (1374) 86 5/16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) ECCP4284 ECCP4884 ECCP5484 ECCP6084 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-25

26 PICTURE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 69 (1765) 75 (1918) 72 (1842) 78 (1994) 66 3/4 (1695) 72 3/4 (1848) 66 (1676) 72 (1829) 60 3/32 (1526) 66 3/32 (1679) 14 5/16 (364) 15 13/16 (402) 12 3/4 (324) 12 (305) 6 3/32 (155) ECCP6612 ECCP6618 ECCP6620 ECCP7212 ECCP7218 ECCP7220 ECCP6624 ECCP7224 ECCP6628 ECCP /4 (781) 30 (762) 24 3/4 (629) 24 (610) 18 3/4 (476) 18 (457) 20 3/4 (527) 20 (508) ECCP6630 ECCP /4 (933) 36 (914) ECCP6636 ECCP /4 (1086) 42 (1067) ECCP6642 ECCP /16 (1278) 51 13/16 (1316) 48 3/4 (1238) 48 (1219) 42 3/32 (1070) 44 5/16 (1126) 45 13/16 (1164) 28 3/4 (730) 28 (711) 20 5/16 (515) 21 13/16 (554) 22 5/16 (578) 23 13/16 (605) 12 3/32 (307) 14 3/32 (358) 36 3/32 (917) 38 5/16 (973) 39 13/16 (1011) 30 3/32 (764) 32 5/16 (821) 33 13/16 (859) 24 3/32 (612) 30 5/16 (770) 31 13/16 (808) 22 3/32 (561) 26 5/16 (668) 27 13/16 (706) 18 3/32 (460) ECCP6648 ECCP7248 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-26

27 PICTURE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 69 (1765) 75 (1918) 72 (1842) 78 (1994) 66 3/4 (1695) 72 3/4 (1848) 66 (1676) 72 (1829) 60 3/32 (1526) 66 3/32 (1679) ECCP6654 ECCP7254 ECCP6660 ECCP /4 (1695) 66 (1676) 60 3/4 (1543) 60 (1524) 54 3/4 (1391) 54 (1372) ECCP6666 ECCP /4 (1848) 72 (1829) ECCP6672 ECCP /16 (2040) 81 13/16 (2078) 78 3/4 (2000) 78 (1981) 72 3/32 (1831) 74 5/16 (1888) 75 13/16 (1926) 66 3/32 (1679) 68 5/16 (1735) 69 13/16 (1773) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 48 3/32 (1222) ECCP6678 ECCP7278 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-27

28 PICTURE UNITS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 69 (1765) 75 (1918) 72 (1842) 78 (1994) 66 3/4 (1695) 72 3/4 (1848) 66 (1676) 72 (1829) 60 3/32 (1526) 66 3/32 (1679) 86 5/16 (2192) 87 13/16 (2230) 84 3/4 (2153) 84 (2134) 78 3/32 (1984) ECCP6684 ECCP7284 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/4 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-28

29 PICTURE UNITS WITH 18 FLANKERS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 81 (2070) 84 (2146) 78 3/4 (2000) 78 (1981) 12 3/32 (307)[2] 36 3/32 (917) 93 (2380) 96 (2451) 90 3/4 (2305) 90 (2286) 12 3/32 (307)[2] 48 3/32 (1222) 105 (2680) 108 (2756) 102 3/4 (2610) 102 (2591) 12 3/32 (307)[2] 60 3/32 (1526) ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF /16 (1735) 69 13/16 (1773) 66 3/4 (1695) 66 (1676) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 60 3/4 (1543) 60 (1524) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 54 3/4 (1391) 54 (1372) 48 3/32 (1222) 44 5/16 (1126) 45 13/16 (1164) 42 3/4 (1086) 42 (1067) 36 3/32 (917) 50 5/16 (1278) 51 13/16 (1316) 48 3/4 (1238) 48 (1219) 42 3/32 (1070) ECCPF ECCPF ECCPF ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-29

30 PICTURE UNITS WITH 20 FLANKERS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 85 (2172) 88 (2248) 82 3/4 (2102) 82 (2083) 14 3/32 (358)[2] 36 3/32 (917) 97 (2477) 100 (2553) 94 3/4 (2407) 94 (2388) 14 3/32 (358)[2] 48 3/32 (1222) 109 (2781) 112 (2858) 106 3/4 (2711) 106 (2692) 14 3/32 (358)[2] 60 3/32 (1526) ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF /16 (1735) 69 13/16 (1773) 66 3/4 (1695) 66 (1676) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 60 3/4 (1543) 60 (1524) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 54 3/4 (1391) 54 (1372) 48 3/32 (1222) 50 5/16 (1278) 51 13/16 (1316) 48 3/4 (1238) 48 (1219) 42 3/32 (1070) 44 5/16 (1126) 45 13/16 (1164) 42 3/4 (1086) 42 (1067) 36 3/32 (917) ECCPF ECCPF ECCPF ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-30

31 PICTURE UNITS WITH 24 FLANKERS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 93 (2380) 96 (2451) 90 3/4 (2305) 90 (2286) 18 3/32 (460)[2] 36 3/32 (917) 105 (2680) 108 (2756) 102 3/4 (2610) 102 (2591) 18 3/32 (460)[2] 48 3/32 (1222) 117 (2985) 120 (3061) 114 3/4 (2915) 114 (2896) 18 3/32 (460)[2] 60 3/32 (1526) ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF /16 (1735) 69 13/16 (1773) 66 3/4 (1695) 66 (1676) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 60 3/4 (1543) 60 (1524) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 54 3/4 (1391) 54 (1372) 48 3/32 (1222) 44 5/16 (1126) 45 13/16 (1164) 42 3/4 (1086) 42 (1067) 36 3/32 (917) 50 5/16 (1278) 51 13/16 (1316) 48 3/4 (1238) 48 (1219) 42 3/32 (1070) ECCPF ECCPF ECCPF ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-31

32 PICTURE UNITS WITH 28 FLANKERS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 101 (2578) 104 (2654) 98 3/4 (2508) 98 (2489) 22 3/32 (561)[2] 36 3/32 (1222) 113 (2883) 116 (2959) 110 3/4 (2813) 110 (2794) 22 3/32 (561)[2] 48 3/32 (1222) ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF ECCPF /16 (1735) 69 13/16 (1773) 66 3/4 (1695) 66 (1676) 60 3/32 (1526) 62 5/16 (1583) 63 13/16 (1621) 60 3/4 (1543) 60 (1524) 54 3/32 (1374) 56 5/16 (1430) 57 13/16 (1468) 54 3/4 (1391) 54 (1372) 48 3/32 (1222) 44 5/16 (1126) 45 13/16 (1164) 42 3/4 (1086) 42 (1067) 36 3/32 (917) 50 5/16 (1278) 51 13/16 (1316) 48 3/4 (1238) 48 (1219) 42 3/32 (1070) ECCPF ECCPF ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note: Elevations shown DO NOT have exterior trim. Subtract (12.7) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE 1/8 = 1 October 2007 JELD-WEN reserves the right to change specifications without notice. Page 1-32