NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: PARAMOUNT WINDOWS CORPORATION

Transcription

1 Architectural Testing NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: PARAMOUNT WINDOWS CORPORATION SERIES/MODEL: ECO-View 6100/7100 Report Number: B Report Date: 02/20/12 Expiration Date: 01/27/ Derry Court York, PA phone: fax:

2 Architectural Testing NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: PARAMOUNT WINDOWS CORPORATION 550 West Southern Ave Tempe, Arizona Report Number: Simulation Date: Report Date: Expiration Date: B /27/12 02/20/12 01/27/16 Project Summary: Architectural Testing, Inc. was contracted to perform U-Factor, Solar Heat Gain Coefficient, Visible Transmittance, and Condensation Resistance* computer simulations in accordance with the National Fenestration Rating Council (NFRC). The products were evaluated in full compliance with NFRC requirements to the standards listed below. *NFRC's Condensation Resistance rating is NOT equivalent to a Condensation Resistance Factor (CRF) determined in accordance with AAMA Standards: NFRC : Procedure for Determining Fenestration Product U-Factors NFRC : Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence NFRC : Procedure for Determining Fenestration Product Condensation Resistance Values Software: Frame and Edge Modeling: THERM Center-of-Glass Modeling: WINDOW Total Product Calculations: WINDOW Spectral Data Library: 21.0 Simulations Specimen Description: Series/Model: ECO-View 6100/7100 Type: Vertical Slider, Single Hung Frame Material: VY Vinyl Sash Material: VI Vinyl w/ Reinforcement - Interlock Standard Size: 1200mm x 1500mm 130 Derry Court York, PA phone: fax:

3 Architectural Testing B Page 2 of 9 Modeling Assumptions/Technical Interpretations: 1) To prevent air infiltration, tape was applied to all interior sash crack locations. 2) Center-of-glass grouping of SS and DS options per NFRC , Section SS options are the group leaders. 3) Frame R1006 and R1744 are groupable per NFRC , Section Frame R1744 is the group leader. Specialty Products Table: The specialty products method allow the manufacturer to determine the overall product SHGC and VT for any glazing option. The center of glass SHGC and/or VT must be determined using WINDOW The method gives overall product SHGC and VT indexed on center of glass properties. All values used in the calculations are truncated to six decimal place precision. No Dividers Dividers < 1 Dividers > 1 SHGC SHGC VT VT SHGC = SHGC0 + SHGCc (SHGC1 - SHGC0) VT = VT0 + VTc (VT1 - VT0) Validation Matrix: The following products are part of a validation matrix. Only one is required for validation testing. Product Line ECO-View 6200/7200 Horizontal Sliding Window ECO-View 6100/7100 Single Hung Window Report Number B B

4 Architectural Testing B Page 3 of 9 Spacer Option Description Sealant Spacer Type Primary Secondary Code Truseal Duralite Spacer Butyl Rubber P1-S Truseal Duraseal Spacer Butyl Rubber Grid Option Description Grid Size Grid Type Grid Pattern 0.118" x 0.813" Aluminum Rectangular Grid - Painted NFRC Standard Reinforcement Option Description Location Lockstile Impost Material Galvanized Aluminum Gas Filling Technique Description Fill Type Method 90% Argon Single Probe - Timed Edge-of-Glass Construction Interior Condition Glazing tape betweeen glass and frame Exterior Condition Glazing Bead against glass Weatherstripping Type Quantity Location Mohair 2 Rows Interlock Mohair 1 Row Bottom Rail & Stiles Frame/Sash Materials Finish Interior Vinyl Exterior Vinyl

5 Architectural Testing B Page 4 of 9 NFRC 100/200/500 Summary Sheet ECO-View 6100/7100 ID Pane Thickness 1 Gap Width 1 U-Factor Pane Thickness 2 Gap Width 2 1 Clr / Air / Clr - 3/4 - (SS-SS) Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Solar Heat Gain Coefficient (SHGC) Grids (None / <1 / >=1) Low-e (Surface#) Visible Transmittance (VT) Grids (None / <1 / >=1) Tint Spacer Grid Type Condensation Resistance AIR CL U-Factor 0.48 SHGC (N / >1) 0.65 / 0.52 VT (N / >1) 0.67 / 0.53 CR 43 Clr / Air / Clr - 3/4 - (DS-DS) AIR CL U-Factor 0.48 SHGC (N / >1) 0.64 / 0.51 VT (N / >1) 0.67 / 0.53 CR 43 2 RLE 5527 / Air / Clr - 3/4 - (SS-SS) AIR 0.024(#2) CL U-Factor 0.34 SHGC (N / >1) 0.23 / 0.19 VT (N / >1) 0.45 / RLE 5527 / Air / RLE /4 - (SS-SS) U-Factor 0.33 SHGC (N / >1) 0.20 / 0.17 RLE 5527 / Air / Clr - 3/4 - (DS-DS) U-Factor 0.33 SHGC (N / >1) 0.23 / 0.19 RLE 5527 / Air / RLE /4 - (DS-DS) U-Factor 0.33 SHGC (N / >1) 0.20 / RLE 5527 / Arg / Clr - 3/4 - (SS-SS) U-Factor 0.30 SHGC (N / >1) 0.23 / RLE 5527 / Arg / RLE /4 - (SS-SS) U-Factor 0.30 SHGC (N / >1) 0.20 / 0.16 RLE 5527 / Arg / Clr - 3/4 - (DS-DS) U-Factor 0.30 SHGC (N / >1) 0.23 / 0.19 RLE 5527 / Arg / RLE /4 - (DS-DS) U-Factor 0.30 SHGC (N / >1) 0.20 / 0.16 AIR 0.024(#2) / 0.024(#3) CL VT (N / >1) 0.30 / 0.24 AIR 0.024(#2) CL VT (N / >1) 0.44 / 0.35 AIR 0.024(#2) / 0.024(#3) CL VT (N / >1) 0.30 / 0.23 ARG (#2) CL VT (N / >1) 0.45 / 0.35 ARG (#2) / 0.024(#3) CL VT (N / >1) 0.30 / 0.24 ARG (#2) CL VT (N / >1) 0.44 / 0.35 ARG (#2) / 0.024(#3) CL VT (N / >1) 0.30 / 0.23 CR 54 CR 54 CR 54 CR 54 CR 57 CR 57 CR 57 CR 57

6 Architectural Testing B Page 5 of 9 NFRC 100/200/500 Summary Sheet ECO-View 6100/7100 ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 6 Clr / Air / Clr - 3/4 - (4mm-4mm) Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance AIR U-Factor 0.48 SHGC (N / >1) 0.63 / 0.50 VT (N / >1) 0.66 / RLE 5527 / Air / Clr - 3/4 - (4mm-4mm) U-Factor 0.34 SHGC (N / >1) 0.23 / RLE 5527 / Air / RLE /4 - (4mm-4mm) U-Factor 0.33 SHGC (N / >1) 0.20 / RLE 5527 / Arg / Clr - 3/4 - (4mm-4mm) U-Factor 0.30 SHGC (N / >1) 0.23 / 0.19 RLE 5527 / Arg / RLE /4 - (4mm-4mm) U-Factor 0.30 SHGC (N / >1) 0.20 / Clr / Air / Clr - 3/4 - (5mm-5mm) U-Factor 0.50 SHGC (N) Clr / Air / Clr - 3/4 - (5mm-5mm) U-Factor 0.50 SHGC (>1) RLE 5527 / Air / Clr - 3/4 - (5mm-5mm) U-Factor 0.36 SHGC (N) RLE 5527 / Air / Clr - 3/4 - (5mm-5mm) U-Factor 0.37 SHGC (>1) RLE 5527 / Air / RLE /4 - (5mm-5mm) U-Factor 0.35 SHGC (N) 0.20 AIR 0.024(#2) CL VT (N / >1) 0.44 / 0.35 AIR 0.024(#2) / 0.024(#3) CL VT (N / >1) 0.29 / 0.23 ARG (#2) CL VT (N / >1) 0.44 / 0.35 ARG (#2) / 0.024(#3) CL AIR AIR VT (N / >1) 0.29 / 0.23 VT (N) 0.66 VT (>1) 0.52 CL CL CL AIR 0.024(#2) CL VT (N) 0.44 AIR 0.024(#2) CL VT (>1) 0.35 AIR 0.024(#2) / 0.024(#3) CL VT (N) 0.29 CR 42 CR 52 CR 52 CR 54 CR 54 N CR 41 G CR 41 N CR 51 G CR 51 N CR 51

7 Architectural Testing B Page 6 of 9 NFRC 100/200/500 Summary Sheet ECO-View 6100/7100 ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 15 RLE 5527 / Air / RLE /4 - (5mm-5mm) AIR 0.024(#2) / 0.024(#3) CL G U-Factor 0.37 SHGC (>1) 0.17 VT (>1) RLE 5527 / Arg / Clr - 3/4 - (5mm-5mm) U-Factor 0.31 SHGC (N) 0.23 RLE 5527 / Arg / RLE /4 - (5mm-5mm) U-Factor 0.31 SHGC (N) RLE 5527 / Arg / Clr - 3/4 - (5mm-5mm) U-Factor 0.32 SHGC (>1) 0.19 RLE 5527 / Arg / RLE /4 - (5mm-5mm) U-Factor 0.32 SHGC (>1) RLE 5527 / Arg / Clr - 3/4 - (SS-SS) U-Factor 0.28 SHGC (N / >1) 0.23 / RLE 5527 / Arg / RLE /4 - (SS-SS) U-Factor 0.28 SHGC (N / >1) 0.20 / 0.16 RLE 5527 / Arg / Clr - 3/4 - (DS-DS) U-Factor 0.28 SHGC (N / >1) 0.23 / 0.19 RLE 5527 / Arg / RLE /4 - (DS-DS) U-Factor 0.28 SHGC (N / >1) 0.20 / RLE 5527 / Arg / Clr - 3/4 - (4mm-4mm) U-Factor 0.28 SHGC (N / >1) 0.23 / 0.19 ARG (#2) CL VT (N) 0.44 ARG (#2) / 0.024(#3) CL VT (N) 0.29 ARG (#2) CL VT (>1) 0.35 ARG (#2) / 0.024(#3) CL VT (>1) 0.23 ARG (#2) CL VT (N / >1) 0.45 / 0.35 ARG (#2) / 0.024(#3) CL VT (N / >1) 0.30 / 0.24 ARG (#2) CL VT (N / >1) 0.44 / 0.35 ARG (#2) / 0.024(#3) CL VT (N / >1) 0.30 / 0.23 ARG (#2) CL VT (N / >1) 0.44 / 0.35 CR 51 N CR 54 N CR 54 G CR 54 P1-S G CR 54 P1-S CR 61 P1-S CR 61 P1-S CR 61 P1-S CR 61 CR 60

8 Architectural Testing B Page 7 of 9 NFRC 100/200/500 Summary Sheet ECO-View 6100/7100 ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance RLE 5527 / Arg / RLE /4 - (4mm-4mm) ARG (#2) / 0.024(#3) CL P1-S U-Factor 0.28 SHGC (N / >1) 0.20 / 0.17 VT (N / >1) 0.29 / 0.23 CR RLE 5527 / Arg / Clr - 3/4 - (5mm-5mm) ARG (#2) CL P1-S N U-Factor 0.30 SHGC (N) 0.23 VT (N) 0.44 CR 58 RLE 5527 / Arg / RLE /4 - (5mm-5mm) ARG (#2) / 0.024(#3) CL P1-S N U-Factor 0.30 SHGC (N) 0.20 VT (N) 0.29 CR RLE 5527 / Arg / Clr - 3/4 - (5mm-5mm) ARG (#2) CL P1-S G U-Factor 0.31 SHGC (>1) 0.19 VT (>1) 0.35 CR 58 RLE 5527 / Arg / RLE /4 - (5mm-5mm) ARG (#2) / 0.024(#3) CL P1-S G U-Factor 0.31 SHGC (>1) 0.17 VT (>1) 0.23 CR 58

9 Architectural Testing B Page 8 of 9 The Condensation Resistance results obtained from this procedure are for controlled laboratory conditions and do not include the effects of air movement through the specimen, solar radiation, and the thermal bridging that may occur due to the specific design and construction of the fenestration system opening. Ratings values included in this report are for submittals to an NFRC-licensed IA and are not meant to be used directly for labeling purposes. Only those values identified on a valid Certification Authorization Report (CAR) by an NFRC accredited Inspection Agency (IA) are to be used for labeling purposes. The ratings values were rounded in accordance to NFRC 601, NFRC Unit and Measurement Policy. Architectural Testing, Inc. is an NFRC accredited simulation laboratory and all simulations were conducted in full compliance with NFRC approved procedures and specifications. The NFRC procedure requires that the computational results be verified through actual test results. Detailed drawings, simulation data files, a copy of this report, or other pertinent project documentation will be retained by Architectural Testing, Inc. for a period of four years from the original test date. At the end of this retention period, such materials shall be discarded without notice and the service life of this report will expire. Results obtained are simulated values and were secured by using the designated test methods. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the product simulated. This report may not be reproduced, except in full, without the written approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, INC.: SIMULATED BY: REVIEWED BY: Elizabeth A. Moser Simulation Technician Michael J. Thoman Director - Simulations and Thermal Testing Simulator-In-Responsible-Charge EAM:eam B Attachments (pages): Appendix A: Drawings and Bills of Material (16) This report is complete only when all attachments listed are included.

10 Architectural Testing B Page 9 of 9 Revision Log Rev. # Date Page(s) Revision(s).01R0 02/20/12 All Original Report Issue. Work Requested by Mr. Howard Hiebert of Paramount This report produced from controlled document template ATI 00037, Revised 08/31/2009.

11 All drawings and Bills of Material used to simulate this product are enclosed in this Appendix Appendix A B

12 PARAMOUNT WINDOWS BILL OF MATERIALS 6100 SH WITH N/W 1-3/8'' FIN SET BACK Description Supplier Part No Costs EA Quantity XO-SH MAIN FRAME Royal R SH VENT RAIL Royal R SH VENT STILE Royal R BOTTOM RAILS AND VENT STILE Royal R XO & SH LOCKSTILE Royal R GLAZING BEAD 3/4 SH/SL/PW Royal R SH VENT STOP AND FFPW FILLER Royal R IMPOST Royal KE WEATHERSTRIPPING Royal.187x.240 inserted in extrusions by Royal as needed 1/16 X 3/8 BLACK GLAZING TAPE Bron GL-NO516-WT 8 Reinforcing / Lockstile Northstar NS Reinforcing / Impost Sierra Aluminum Sweep lock Ultra Hardware Balance/Top and Bottom Guide Caldwell series 86 2 Sash cam Caldwell 15P12 2 Take-out clip Caldwell 15P22 2 Setting blocks Bandlock BL /8"X3/4" 16 BAL/CAMS # 8 X 3/8" PH PN TSA ZINC US INDUSTRIAL 4 Pal Lock # 8 X 3/4 " PH FL TSA BLK US INDUSTRIAL 2 IMPOST # 8 X 1-1/2" PH PANCAKE WAFER TSA ZINC US INDUSTRIAL 4 C:\Users\emoser\AppData\Local\Temp\Temp2_vinyl window test submittal documents.zip\vinyl window test submittal documents\window and Door BOM

13

14 PARAMOUNT WINDOWS BILL OF MATERIALS 7100 SH WITH FLUSH FIN FOR RETRO FIT APPLICATION Description Supplier Part No Costs EA Quantity FLUSH FIN MAIN FRAME Royal R SH VENT RAIL Royal R SH VENT STILE Royal R BOTTOM RAILS AND VENT STILE Royal R XO & SH LOCKSTILE Royal R GLAZING BEAD 3/4 SH/SL/PW Royal R SH VENT STOP AND FFPW FILLER Royal R IMPOST Royal KE WEATHERSTRIPPING Royal.187x.240 inserted in extrusions by Royal as needed 1/16 X 3/8 BLACK GLAZING TAPE Bron GL-NO516-WT 8 Reinforcing / Lockstile Northstar NS Reinforcing / Impost Sierra Aluminum Sweep lock Ultra Hardware Balance/Top and Bottom Guide Caldwell series 86 2 Sash cam Caldwell 15P12 2 Take-out clip Caldwell 15P22 2 Setting blocks Bandlock BL /8"X3/4" 16 BAL/CAMS # 8 X 3/8" PH PN TSA ZINC US INDUSTRIAL 4 Pal Lock # 8 X 3/4 " PH FL TSA BLK US INDUSTRIAL 2 IMPOST # 8 X 1-1/2" PH PANCAKE WAFER TSA ZINC US INDUSTRIAL 4 C:\Users\emoser\AppData\Local\Temp\Temp2_vinyl window test submittal documents.zip\vinyl window test submittal documents\window and Door BOM

15

16

17

18

19

20

21

22

23

24

25

26

27 A Muntin Bar Aluminum: Painted, Mill Finish, Clear & Color-In TM Anodized B TOLERANCE A, ±.005 (.127mm) B, ±.005 (.127mm) SPECIAL NOTICE Cleaning and Handling of Muntin Bar We recommend muntin bar to be wiped clean before installation into an insulating glass unit. A household grade liquid cleaner may be used for this purpose. To avoid breakdown of painted surfaces, do not use M.E.K., Triethane, Alcohol or like substances for the cleaning of painted muntin bar. When machining and processing muntin bar in your plant, keep saw tables and work areas free of saw cut filings to avoid scratching the painted surfaces. Muntin Bar Size Part # Packaging Information Pieces Per Shipping Carton 12' 8" Lengths Lineal Feet Per Shipping Carton 12' 8" Lengths 1/8 x /16 x 9/ /16 x /16 x 5/ /16 x 3/ /16 x 13/ /16 x /4 x 9/ /4 x 5/ /4 x 3/ /4 x 13/ /4 x /4 x 1 1/ /16 x /8 x 5/ /8 x 3/ /8 x 13/ /8 x 7/ /8 x /8(.375) x 3/ /16 x 3/ /16 x 3/ ** /16 x 1/ /16 x 5/ /2 x 3/4* /2 x Specification In Inches Muntin Bar Size A B 1/8 x /16 x 9/ /16 x /16 x 5/ /16 x 3/ /16 x 13/ /16 x /4 x 9/ /4 x 5/ /4 x 3/ /4 x 13/ /4 x /4 x 1 1/ /16 x /8 x 5/ /8 x 3/ /8 x 13/ /8 x 7/ /8 x /8(.375) x 3/ /16 x 3/ /16 x 3/ /16 x 1/ /16 x 5/ /2 x 3/4* /2 x Part numbers shown are standard white color. Material thickness:.0185 Available in tutone. Please see Color Selection Chart located in front of catalog. Part number shown is Dark Bronze Anodized Color. * Part number shown is Clear Anodized. **Part number shown is white welded. Note: Available in pre-cut lengths and pre-notched; tutone and post-painted. Custom colors also available. D 2 Please see terms & conditions of sale. Copyright 2008 Allmetal, Inc.