NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. (Revised) Rendered to: EARTHWISE GROUP, L.L.C
|
|
- James White
- 6 years ago
- Views:
Transcription
1 NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT (Revised) Rendered to: EARTHWISE GROUP, L.L.C SERIES/MODEL: Patio Door Report Number: Original Report Date: Revised Report Date: D /27/15 04/14/ Derry Court York, PA p f
2 NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT (Revised) Rendered to: EARTHWISE GROUP, L.L.C 5796 Cedarview Court Liberty Township, Ohio Report Number: Simulation Date: Original Report Date: Revised Report Date: D /23/15 03/27/15 04/14/15 Project Summary: Architectural Testing, Inc. was contracted to perform U-Factor, Solar Heat Gain Coefficient, Visible Transmittance, and Condensation Resistance* computer simulations in accordance with the National Fenestration Rating Council (NFRC). The products were evaluated in full compliance with NFRC requirements to the standards listed below. *NFRC's Condensation Resistance rating is NOT equivalent to a Condensation Resistance Factor (CRF) determined in accordance with AAMA Standards: NFRC : Procedure for Determining Fenestration Product U-Factors NFRC : Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence NFRC : Procedure for Determining Fenestration Product Condensation Resistance Values Software: Frame and Edge Modeling: THERM Center-of-Glass Modeling: WINDOW Total Product Calculations: WINDOW Spectral Data Library: IGDB 40.0 Simulations Specimen Description: Series/Model: Patio Door Type: Sliding Glass Door, Sliding Glass Door (XX or OX) Frame Material: VY Vinyl Sash Material: VP Vinyl w/ Reinforcement - Partial Standard Size: 2000mm x 2000mm 130 Derry Court York, PA p f
3 D Page 2 of 22 Revised Report Date: 04/14/15 Modeling Assumptions/Technical Interpretations: 1) To prevent air infiltration, tape was applied to all interior sash crack locations. Specialty Products Table: The specialty products method allow the manufacturer to determine the overall product SHGC and VT for any glazing option. The center of glass SHGC and/or VT must be determined using WINDOW The method gives overall product SHGC and VT indexed on center of glass properties. All values used in the calculations are truncated to six decimal place precision. No Dividers Dividers < 1 Dividers > 1 SHGC SHGC VT VT SHGC = SHGC0 + SHGCc (SHGC1 - SHGC0) VT = VT0 + VTc (VT1 - VT0) Validation Matrix: The following products are part of a validation matrix. Only one is required for validation testing. Product Line Report Number None -
4 D Page 3 of 22 Revised Report Date: 04/14/15 Spacer Option Description Sealant Spacer Type Primary Secondary Code Quanex Duraseal Spacer Butyl Rubber None A8-S Cardinal XL Edge Spacer PIB Silicone SS-D Ramapo Aluminum Spacer PIB Silicone A1-D Grid Option Description Grid Size Grid Type Grid Pattern 3/16" x 13/16" Aluminum Flat Grid (Painted) NFRC Standard Reinforcement Option Description Location All vertical sash members and interior bottom rail Material Aluminum Gas Filling Technique Description Fill Type Method 90% Argon Single probe 95% Argon Dual probe Edge-of-Glass Construction Interior Condition Silicone between PVC sash and glass Exterior Condition PVC Glazing Bead against glass Weatherstripping Type Quantity Location Finpile 2 rows Head, Exterior Sill and Interior Jamb Frame Finpile 1 row Interior Sill Frame, Exterior Jamb Frame and Frame/Sash Materials Finish Interior Vinyl Exterior Vinyl
5 D Page 4 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 U-Factor Pane Thickness 2 1 EAS: clr / air / clr (DS/DS) - 1" IG U-Factor 0.46 SHGC (N / <1) 0.54 / 0.47 VT (N / <1) 0.57 / EAS: SB60 / air / clr (DS/DS) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.51 / EAS: SB70 / air / clr (DS/DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: E366 / air / clr (DS/DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / air / clr (4mm/4mm) - 1" IG U-Factor 0.46 SHGC (N / <1) 0.53 / 0.46 VT (N / <1) 0.57 / EAS: SB60 / air / clr (4mm/4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / air / clr (4mm/4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: E366 / air / clr (4mm/4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / air / clr (5mm/5mm) - 1" IG U-Factor 0.46 SHGC (N / <1) 0.51 / 0.45 VT (N / <1) 0.56 / EAS: SB60 / air / clr (5mm/5mm) - 1" IG Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 AIR CL A8-S N,G AIR 0.035(#2) CL A8-S N,G AIR 0.018(#2) CL A8-S N,G AIR 0.022(#2) CL A8-S N,G AIR CL A8-S N,G AIR 0.035(#2) CL A8-S N,G AIR 0.018(#2) CL A8-S N,G AIR 0.022(#2) CL A8-S N,G AIR CL A8-S N,G AIR 0.035(#2) CL A8-S N,G U-Factor 0.34 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / 0.43 Gap Fill Solar Heat Gain Coefficient (SHGC) Grids (None / <1 / >=1) Low-e (Surface#) Tint Visible Transmittance (VT) Grids (None / <1 / >=1) Spacer Grid Type Condensation Resistance CR 45 CR 45 CR 45 CR 55
6 D Page 5 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 11 EAS: SB70 / air / clr (5mm/5mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: E366 / air / clr (5mm/5mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / arg / clr (DS/DS) - 1" IG U-Factor 0.45 SHGC (N / <1) 0.54 / 0.47 VT (N / <1) 0.57 / EAS: SB60 / arg / clr (DS/DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.51 / EAS: SB70 / arg / clr (DS/DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: E366 / arg / clr (DS/DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / arg / clr (4mm/4mm) - 1" IG U-Factor 0.44 SHGC (N / <1) 0.53 / 0.46 VT (N / <1) 0.57 / EAS: SB60 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: E366 / arg / clr (4mm/4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance AIR 0.018(#2) CL A8-S N,G AIR 0.022(#2) CL A8-S N,G ARG90 CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G ARG90 CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / 0.39 CR 46 CR 46
7 D Page 6 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 21 EAS: clr / arg / clr (5mm/5mm) - 1" IG U-Factor 0.44 SHGC (N / <1) 0.51 / 0.45 VT (N / <1) 0.56 / EAS: SB60 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.44 / EAS: E366 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / air / clr (DS/DS) - 1" IG U-Factor 0.46 SHGC (N / <1) 0.54 / 0.47 VT (N / <1) 0.57 / EAS: E270 / air / clr (DS/DS) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.49 / EAS: E240 / air / clr (DS/DS) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.19 / 0.16 VT (N / <1) 0.28 / EAS: E340 / air / clr (DS/DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.27 / EAS: E366 / air / clr (DS/DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / air / clr (4mm/4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance ARG90 ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G AIR CL SS-D N,G AIR 0.037(#2) CL SS-D N,G AIR 0.057(#2) CL SS-D N,G AIR 0.028(#2) CL SS-D N,G AIR 0.022(#2) CL SS-D N,G AIR CL SS-D N,G U-Factor 0.46 SHGC (N / <1) 0.53 / 0.46 VT (N / <1) 0.57 / 0.49 CL A8-S N,G CR 46 CR 45 CR 55 CR 45
8 D Page 7 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 31 EAS: E270 / air / clr (4mm/4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.48 / EAS: E240 / air / clr (4mm/4mm) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.27 / EAS: E340 / air / clr (4mm/4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.27 / EAS: E366 / air / clr (4mm/4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / air / clr (5mm/5mm) - 1" IG U-Factor 0.46 SHGC (N / <1) 0.51 / 0.45 VT (N / <1) 0.56 / EAS: E270 / air / clr (5mm/5mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.48 / EAS: E240 / air / clr (5mm/5mm) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.27 / EAS: E340 / air / clr (5mm/5mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.27 / EAS: E366 / air / clr (5mm/5mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / arg / clr (DS/DS) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance AIR 0.037(#2) CL SS-D N,G AIR 0.057(#2) CL SS-D N,G AIR 0.028(#2) CL SS-D N,G AIR 0.022(#2) CL SS-D N,G AIR CL SS-D N,G AIR 0.037(#2) CL SS-D N,G AIR 0.057(#2) CL SS-D N,G AIR 0.028(#2) CL SS-D N,G AIR 0.022(#2) CL SS-D N,G ARG90 CL SS-D N,G U-Factor 0.45 SHGC (N / <1) 0.54 / 0.47 VT (N / <1) 0.57 / 0.49 CR 55 CR 55 CR 55 CR 44 CR 55 CR 54 CR 55 CR 55 CR 46
9 D Page 8 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 41 EAS: E270 / arg / clr (DS/DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.49 / EAS: E240 / arg / clr (DS/DS) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.28 / EAS: E340 / arg / clr (DS/DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.27 / EAS: E366 / arg / clr (DS/DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / arg / clr (4mm/4mm) - 1" IG U-Factor 0.44 SHGC (N / <1) 0.53 / 0.46 VT (N / <1) 0.57 / EAS: E270 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.48 / EAS: E240 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.27 / EAS: E340 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.27 / EAS: E366 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / arg / clr (5mm/5mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG90 CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG90 CL SS-D N,G U-Factor 0.44 SHGC (N / <1) 0.51 / 0.45 VT (N / <1) 0.56 / 0.49 CR 46 CR 46
10 D Page 9 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 51 EAS: E270 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.48 / EAS: E240 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.27 / EAS: E340 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.27 / EAS: E366 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / air / clr (DS/DS) - 1" IG U-Factor 0.47 SHGC (N / <1) 0.54 / 0.47 VT (N / <1) 0.57 / EAS: SB60 / air / clr (DS/DS) - 1" IG U-Factor 0.36 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.51 / EAS: SB70 / air / clr (DS/DS) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / EAS: clr / air / clr (4mm/4mm) - 1" IG U-Factor 0.47 SHGC (N / <1) 0.53 / 0.46 VT (N / <1) 0.57 / EAS: SB60 / air / clr (4mm/4mm) - 1" IG U-Factor 0.36 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / air / clr (4mm/4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G AIR CL A1-D N,G AIR 0.035(#2) CL A1-D N,G AIR 0.018(#2) CL A1-D N,G AIR CL A1-D N,G AIR 0.035(#2) CL A1-D N,G AIR 0.018(#2) CL A1-D N,G U-Factor 0.35 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.45 / 0.39 CR 40 CR 49 CR 49 CR 40 CR 48 CR 49
11 D Page 10 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 61 EAS: clr / air / clr (5mm/5mm) - 1" IG U-Factor 0.47 SHGC (N / <1) 0.51 / 0.45 VT (N / <1) 0.56 / EAS: SB60 / air / clr (5mm/5mm) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / air / clr (5mm/5mm) - 1" IG U-Factor 0.35 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: clr / arg / clr (DS/DS) - 1" IG U-Factor 0.46 SHGC (N / <1) 0.54 / 0.47 VT (N / <1) 0.57 / EAS: SB60 / arg / clr (DS/DS) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.51 / EAS: SB70 / arg / clr (DS/DS) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / arg / clr (4mm/4mm) - 1" IG U-Factor 0.45 SHGC (N / <1) 0.53 / 0.46 VT (N / <1) 0.57 / EAS: SB60 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / arg / clr (4mm/4mm) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.45 / EAS: clr / arg / clr (5mm/5mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance AIR AIR 0.035(#2) CL A1-D N,G AIR 0.018(#2) CL A1-D N,G ARG90 CL A1-D N,G ARG (#2) CL A1-D N,G ARG (#2) CL A1-D N,G ARG90 CL A1-D N,G ARG (#2) CL A1-D N,G ARG (#2) CL A1-D N,G ARG90 CL A1-D N,G U-Factor 0.45 SHGC (N / <1) 0.51 / 0.45 VT (N / <1) 0.56 / 0.49 CL A1-D N,G CR 40 CR 48 CR 48 CR 42 CR 51 CR 52 CR 41 CR 50 CR 51 CR 41
12 D Page 11 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor 71 EAS: SB60 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.50 / EAS: SB70 / arg / clr (5mm/5mm) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.20 / 0.17 VT (N / <1) 0.44 / EAS: clr / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.44 SHGC (N / <1) 0.51 / 0.44 VT (N / <1) 0.55 / EAS: SB60 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.32 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: E366 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: clr / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.45 SHGC (N / <1) 0.50 / 0.43 VT (N / <1) 0.55 / EAS: SB60 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: E366 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance ARG (#2) CL A1-D N,G ARG (#2) CL A1-D N,G AIR CL A8-S N,G AIR 0.035(#2) CL A8-S N,G AIR 0.018(#2) CL A8-S N,G AIR 0.022(#2) CL A8-S N,G AIR CL A8-S N,G AIR 0.035(#2) CL A8-S N,G AIR 0.018(#2) CL A8-S N,G AIR 0.022(#2) CL A8-S N,G U-Factor 0.33 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / 0.38 CR 50 CR 50 CR 46 CR 45
13 D Page 12 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.46 SHGC (N) 0.48 VT (N) EAS: clr / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.47 SHGC (<1) 0.42 VT (<1) EAS: SB60 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.35 SHGC (N) 0.28 VT (N) EAS: SB60 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.37 SHGC (<1) 0.25 VT (<1) EAS: SB70 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.35 SHGC (N) 0.20 VT (N) EAS: SB70 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.37 SHGC (<1) 0.18 VT (<1) EAS: E366 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.35 SHGC (N) 0.20 VT (N) EAS: E366 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.37 SHGC (<1) 0.18 VT (<1) EAS: clr / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.43 SHGC (N / <1) 0.51 / 0.44 VT (N / <1) 0.55 / EAS: SB60 / arg / clr-lami (DS/DS 090 DS) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 81 EAS: clr / air / clr-lami (5mm/5mm 090 5mm) - 1" IG AIR AIR CL A8-S G AIR 0.035(#2) CL A8-S N AIR 0.035(#2) CL A8-S G AIR 0.018(#2) CL A8-S N AIR 0.018(#2) CL A8-S G AIR 0.022(#2) CL A8-S N AIR 0.022(#2) CL A8-S G ARG90 CL A8-S N,G ARG (#2) CL A8-S N,G U-Factor 0.30 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / 0.43 CL A8-S N CR 44 CR 44 CR 54 CR 54 CR 54 CR 54 CR 54 CR 54 CR 47
14 D Page 13 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.29 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: E366 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: clr / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.43 SHGC (N / <1) 0.50 / 0.44 VT (N / <1) 0.55 / EAS: SB60 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.29 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: E366 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.29 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: clr / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.44 SHGC (N) 0.48 VT (N) EAS: clr / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.45 SHGC (<1) 0.42 VT (<1) EAS: SB60 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.31 SHGC (N) 0.28 VT (N) EAS: SB60 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 91 EAS: SB70 / arg / clr-lami (DS/DS 090 DS) - 1" IG ARG90 ARG (#2) CL A8-S N,G ARG90 CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G ARG (#2) CL A8-S N,G ARG90 CL A8-S N ARG90 CL A8-S G ARG (#2) CL A8-S N ARG (#2) CL A8-S G U-Factor 0.33 SHGC (<1) 0.24 VT (<1) (#2) CL A8-S N,G CR 47 CR 46 CR 46
15 D Page 14 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.31 SHGC (N) 0.20 VT (N) EAS: SB70 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.33 SHGC (<1) 0.18 VT (<1) EAS: E366 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.31 SHGC (N) 0.20 VT (N) EAS: E366 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.33 SHGC (<1) 0.18 VT (<1) EAS: clr / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.44 SHGC (N / <1) 0.51 / 0.44 VT (N / <1) 0.55 / EAS: E270 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.48 / EAS: E240 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.27 / EAS: E340 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.26 / EAS: E366 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: clr / air / clr-lami (4mm/4mm 090 4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 101 EAS: SB70 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG ARG (#2) CL A8-S N ARG (#2) CL A8-S G ARG (#2) CL A8-S N ARG (#2) CL A8-S G AIR CL SS-D N,G AIR 0.037(#2) CL SS-D N,G AIR 0.057(#2) CL SS-D N,G AIR 0.028(#2) CL SS-D N,G AIR 0.022(#2) CL SS-D N,G AIR CL SS-D N,G U-Factor 0.45 SHGC (N / <1) 0.50 / 0.43 VT (N / <1) 0.55 / 0.48 CR 46 CR 45
16 D Page 15 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.33 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.47 / EAS: E240 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.26 / EAS: E340 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.26 / EAS: E366 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.33 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: clr / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.46 SHGC (N) 0.48 VT (N) EAS: clr / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.47 SHGC (<1) 0.42 VT (<1) EAS: E270 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.36 SHGC (N) 0.26 VT (N) EAS: E270 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.38 SHGC (<1) 0.23 VT (<1) EAS: E240 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.36 SHGC (N) 0.18 VT (N) EAS: E240 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 111 EAS: E270 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG AIR AIR 0.057(#2) CL SS-D N,G AIR 0.028(#2) CL SS-D N,G AIR 0.022(#2) CL SS-D N,G AIR CL SS-D N AIR CL SS-D G AIR 0.037(#2) CL SS-D N AIR 0.037(#2) CL SS-D G AIR 0.057(#2) CL SS-D N AIR 0.057(#2) CL SS-D G U-Factor 0.38 SHGC (<1) 0.16 VT (<1) (#2) CL SS-D N,G CR 55 CR 55 CR 55 CR 44 CR 44 CR 52 CR 52 CR 52 CR 52
17 D Page 16 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.35 SHGC (N) 0.14 VT (N) EAS: E340 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.37 SHGC (<1) 0.13 VT (<1) EAS: E366 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.35 SHGC (N) 0.20 VT (N) EAS: E366 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.37 SHGC (<1) 0.18 VT (<1) EAS: clr / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.43 SHGC (N / <1) 0.51 / 0.44 VT (N / <1) 0.55 / EAS: E270 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.26 / 0.23 VT (N / <1) 0.48 / EAS: E240 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.27 / EAS: E340 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.13 / 0.11 VT (N / <1) 0.26 / EAS: E366 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: clr / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 121 EAS: E340 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG AIR 0.028(#2) CL SS-D N AIR 0.028(#2) CL SS-D G AIR 0.022(#2) CL SS-D N AIR 0.022(#2) CL SS-D G ARG90 CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG90 CL SS-D N,G U-Factor 0.43 SHGC (N / <1) 0.50 / 0.44 VT (N / <1) 0.55 / 0.48 CR 53 CR 53 CR 53 CR 53 CR 47 CR 47
18 D Page 17 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.30 SHGC (N / <1) 0.25 / 0.22 VT (N / <1) 0.47 / EAS: E240 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.18 / 0.16 VT (N / <1) 0.26 / EAS: E340 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.30 SHGC (N / <1) 0.13 / 0.12 VT (N / <1) 0.26 / EAS: E366 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.29 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: clr / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.44 SHGC (N) 0.48 VT (N) EAS: clr / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.45 SHGC (<1) 0.42 VT (<1) EAS: E270 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.32 SHGC (N) 0.26 VT (N) EAS: E270 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.33 SHGC (<1) 0.23 VT (<1) EAS: E240 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.32 SHGC (N) 0.18 VT (N) EAS: E240 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 131 EAS: E270 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG ARG90 ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG (#2) CL SS-D N,G ARG90 CL SS-D N ARG90 CL SS-D G ARG (#2) CL SS-D N ARG (#2) CL SS-D G ARG (#2) CL SS-D N ARG (#2) CL SS-D G U-Factor 0.34 SHGC (<1) 0.16 VT (<1) (#2) CL SS-D N,G CR 45 CR 45
19 D Page 18 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.31 SHGC (N) 0.13 VT (N) EAS: E340 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.33 SHGC (<1) 0.12 VT (<1) EAS: E366 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.31 SHGC (N) 0.20 VT (N) EAS: E366 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.33 SHGC (<1) 0.18 VT (<1) EAS: clr / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.45 SHGC (N / <1) 0.51 / 0.44 VT (N / <1) 0.55 / EAS: SB60 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / air / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / EAS: clr / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.45 SHGC (N / <1) 0.50 / 0.43 VT (N / <1) 0.55 / EAS: SB60 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.34 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / air / clr-lami (4mm/4mm 090 4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 141 EAS: E340 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG ARG (#2) CL SS-D N ARG (#2) CL SS-D G ARG (#2) CL SS-D N ARG (#2) CL SS-D G AIR CL A1-D N,G AIR 0.035(#2) CL A1-D N,G AIR 0.018(#2) CL A1-D N,G AIR CL A1-D N,G AIR 0.035(#2) CL A1-D N,G AIR 0.018(#2) CL A1-D N,G U-Factor 0.34 SHGC (N / <1) 0.20 / 0.18 VT (N / <1) 0.44 / 0.38 CR 43 CR 51 CR 51 CR 42 CR 50 CR 50
20 D Page 19 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.47 SHGC (N) 0.48 VT (N) EAS: clr / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.48 SHGC (<1) 0.42 VT (<1) EAS: SB60 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.37 SHGC (N) 0.28 VT (N) EAS: SB60 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.38 SHGC (<1) 0.25 VT (<1) EAS: SB70 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.36 SHGC (N) 0.20 VT (N) EAS: SB70 / air / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.38 SHGC (<1) 0.18 VT (<1) EAS: clr / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.44 SHGC (N / <1) 0.51 / 0.44 VT (N / <1) 0.55 / EAS: SB60 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / arg / clr-lami (DS/DS 090 DS) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: clr / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 151 EAS: clr / air / clr-lami (5mm/5mm 090 5mm) - 1" IG AIR AIR CL A1-D G AIR 0.035(#2) CL A1-D N AIR 0.035(#2) CL A1-D G AIR 0.018(#2) CL A1-D N AIR 0.018(#2) CL A1-D G ARG90 CL A1-D N,G ARG (#2) CL A1-D N,G ARG (#2) CL A1-D N,G ARG90 CL A1-D N,G U-Factor 0.44 SHGC (N / <1) 0.50 / 0.44 VT (N / <1) 0.55 / 0.48 CL A1-D N CR 41 CR 41 CR 48 CR 48 CR 48 CR 48 CR 44 CR 53 CR 53 CR 43
21 D Page 20 of 22 Revised Report Date: 04/14/15 NFRC 100/200/500 Summary Sheet Patio Door ID Pane Thickness 1 Gap Width 1 Pane Thickness 2 Gap Width 2 Pane Thickness 3 Gap Width 3 Pane Thickness 4 Gap Fill Low-e (Surface#) Tint Spacer Grid Type U-Factor U-Factor 0.31 SHGC (N / <1) 0.28 / 0.25 VT (N / <1) 0.49 / EAS: SB70 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG U-Factor 0.31 SHGC (N / <1) 0.19 / 0.17 VT (N / <1) 0.44 / EAS: clr / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.45 SHGC (N) 0.48 VT (N) EAS: clr / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.46 SHGC (<1) 0.42 VT (<1) EAS: SB60 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.33 SHGC (N) 0.28 VT (N) EAS: SB60 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.34 SHGC (<1) 0.24 VT (<1) EAS: SB70 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG U-Factor 0.32 SHGC (N) 0.20 VT (N) EAS: SB70 / arg / clr-lami (5mm/5mm 090 5mm) - 1" IG Solar Heat Gain Coefficient (SHGC) Visible Transmittance (VT) Condensation Grids (None / <1 / >=1) Grids (None / <1 / >=1) Resistance 161 EAS: SB60 / arg / clr-lami (4mm/4mm 090 4mm) - 1" IG ARG90 ARG (#2) CL A1-D N,G ARG90 CL A1-D N ARG90 CL A1-D G ARG (#2) CL A1-D N ARG (#2) CL A1-D G ARG (#2) CL A1-D N ARG (#2) CL A1-D G U-Factor 0.34 SHGC (<1) 0.18 VT (<1) (#2) CL A1-D N,G CR 52 CR 53 CR 43 CR 42 CR 51 CR 51 CR 51 CR 51
22 D Page 21 of 22 Revised Report Date: 04/14/15 The Condensation Resistance results obtained from this procedure are for controlled laboratory conditions and do not include the effects of air movement through the specimen, solar radiation, and the thermal bridging that may occur due to the specific design and construction of the fenestration system opening. Ratings values included in this report are for submittals to an NFRC-licensed IA and are not meant to be used directly for labeling purposes. Only those values identified on a valid Certification Authorization Report (CAR) by an NFRC accredited Inspection Agency (IA) are to be used for labeling purposes. The ratings values were rounded in accordance to NFRC 601, NFRC Unit and Measurement Policy. Architectural Testing, Inc. is an NFRC accredited simulation laboratory and all simulations were conducted in full compliance with NFRC approved procedures and specifications. The NFRC procedure requires that the computational results be verified through actual test results. This report is reissued in the name of Earthwise Group, L.L.C through written authorization of Deceuninck North America, LLC, to whom the original report was rendered. The original Deceuninck North America, LLC report number is D Architectural Testing will service this report for the entire test record retention period. Test records that are retained such as detailed drawings, datasheets, representative samples of test specimens, or other pertinent project documentation will be retained by Architectural Testing, Inc. for the entire test record retention period. The test record retention end date for this report is March 23, Results obtained are simulated values and were secured by using the designated test methods. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the product simulated. This report may not be reproduced, except in full, without the written approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, INC.: SIMULATED BY: REVIEWED BY: Eric S. Leitner Simulation Technician Kristen L. Louder Senior Simulation Technician Simulator-In-Responsible-Charge ESL:esl D Attachments (pages): This report is complete only when all attachments listed are included. Appendix A: Drawings and Bills of Material (21)
23 D Page 22 of 22 Revised Report Date: 04/14/15 Revision Log Rev. # Date Page(s) Revision(s).01R0 03/23/15 All - Original Report Issued to Deceuninck North America, LLC.03R0 03/27/15 All - Reissued report in the name of Earthwise Group, L.L.C..03R1 04/14/15 All - Corrected sill insert, MR & HI air cavities - Updated SHGC/VT table - Updated drawing package This report produced from controlled document template ATI 00037, Revised 10/2/2012.
24 All drawings and Bills of Material used to simulate this product are enclosed in this Appendix Some drawings may be omitted at the extruder's request. Appendix A D
25 CAD MAINTAINED. CHANGES SHALL BE INCORPORATED BY THE DESIGN ACTIVITY. REVISION HISTORY REV DESCRIPTION DATE APPROVED /21/ usjgm CONFIDENTIAL UNPUBLISHED WORK ' 2010 DECEUNINCK NORTH AMERICA THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS. UNLESS OTHERWISE SPECIFIED DIM ARE IN INCHES TOL ON ANGLES 1 2 PL: 0.010" 3 PL: 0.005" INTERPRET DIM AND TOL PER ASME Y14.5M THIRD ANGLE PROJECTION DESIGN BY: DRAWN BY: FILENAME: JGM 08/10/08 JGM 10/08/ NORTH GARVER ROAD MONROE, OHIO NORTH AMERICA NAME: SIZE DWG. NO: D PD REV PD-003 NEW \\monsrv01\dectech$\data\dgn\77167.dgn SCALE: (LBS/FT.) SHEET: 1 : 1
26 PD BILL OF MATERIALS 2 LITE ITEM NO. DESCRIPTION QUANTITY PART NO. FAB DWG. NO SOURCE 1 HEAD F-01 A 2 JAMB F-05 A 3 EXTERIOR FRAME COVER F-01 A 4 INTERIOR FRAME COVER STRAIGHT CUT A 5 SILL F-01 A 6 SILL THRESHOLD F-01 PPPP 7 SILL RISER F-01 A 8 WEATHER-STRIPPING x.250 AS REQ'D W21255MW HHHH 9 10 MISC SNUBBER F-01 PPPP 11 ROLLER TRACK CAP STRAIGHT CUT N 12 L - BRACKET 2 011H027 LLLL 13 SILL FRAME GASKET 2 QUAS CANLK CC KEEPER 1 F KEEPER - YZD MILD STEEL DECU KEEPER - STAINLESS STEEL DECU SCREEN KEEPER 1 011H040 MMMM 19 BUMPER STOP F SCREWS SNUBBER 16 #8 x 1.25" PFH - ZINC 22 L - BRACKET - HEAD & SASH 8 #8A x 1" PFH - ZINC 23 L - BRACKET - HEAD & SASH 4 #8 x 2.5" PFH - ZINC 24 KEEPER (INSTALLATION) 2 #8 x 2.5" PFH - ZINC 25 SILL RISER 4 #8 x 1.25" PFH - ZINC 26 FRAME ASSEMBLY 12 #8 x 3" PPH - ZINC 27 SCREEN KEEPER 2 #6 x.375" PPH REV DATE DESCRIPTION BY MONROE, OH COPYRIGHT 2008 NAME: PD CONFIDENTIAL DWN BY: JGM UNPUBLISHED WORK 2008 CHKD BY: DECEUNINCK NORTH AMERICA DWG NO: PD-005 THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS.
27 ITEM NO. DESCRIPTION QUANTITY PART NO. FAB DWG. NO SOURCE 1 FXD PNL TOP RAIL F-01 A 2 STILE F-01 A 3 BOTTOM RAIL F-02 A 4 INTERLOCK F-04 A 5 SCREW COVER STRAIGHT CUT A 6 GLAZING BEAD F-01 A 7 STILE REINFORCEMENT - JAMB STRAIGHT CUT PPPP 8 STILE REINFORCEMENT - INTERLOCK STRAIGHT CUT PPPP 9 WEATHER-STRIPPING x.250 AS REQ'D W21255MW HHHH OPR PNL RAIL - TOP F-01 A 12 STILE - INTERLOCK F-03 A 13 STILE - LOCK F-04 A 14 RAIL - BOTTOM F-05 A 15 INTERLOCK F-02 A 16 SCREW COVER STRAIGHT CUT A 17 GLAZING BEAD F-01 A 18 STILE REINFORCEMENT - INTERLOCK STRAIGHT CUT PPPP 19 STILE REINFORCEMENT - LOCK F-01 PPPP 20 RAIL REINFORCEMENT - BOTTOM F-01 PPPP 21 WEATHER-STRIPPING x.250 AS REQ'D W21255MW HHHH MISC LOCK SET ASSEMBLY LOCK W/ TRIMPLATE 1 DECU-XXX4 ADH-3006 AMESBURY F 24 HANDLE SET ASSEMBLY / AMESBURY F 25 HANDLE SET - INTERIOR SWITCH DECU-XXX1 AMESBURY 26 HANDLE SET - INTERIOR SWITCH / KEY DECU-XXX2 27 HANDLE SET - BLANK DECU-XXX3 28 ROLLER ASSEMBLY - PRECISION 1.66" WHEEL TRUTH F 29 DRAFT PLUG DIA. 2 HHHH 30 3/8" HOLE PLUG D 31 IMPACT BRACKET 2 011H055-D MMMM 32 1" INSULATED GLASS - NOTE 2 REFER TO APPLICABLE TEST REPORT 33 SETTING BLOCKS (REFER TO IG SUPPLIER GUIDELINES) AS REQ'D REFER TO APPLICABLE TEST REPORT 34 GLAZING COMPOUND AS REQ'D REFER TO APPLICABLE TEST REPORT VENTURE TAPE SCREWS LOCK SET 2 #8 x 1.5" PFH - ZINC 37 ROLLER ASSEMBLY 4 #8 x 1" PPH - ZINC 38 FIXED PANEL TO JAMB 10 #8 x.75" PFH - PAINTED 39 REINFORCMENT TO PANEL AS REQ'D #8 x 1" PFH - ZINC 40 INTERLOCK AS REQ'D #8 x.75" PPH - ZINC 41 IMPACT BRACKET 6 #8 x 3" PFH - PAINTED 42 NOTE LAMINATED GLASS UTILIZES.090" SOLUTIA PVB REV DATE DESCRIPTION BY PD BILL OF MATERIALS 2 LITE MONROE, OH COPYRIGHT 2008 NAME: CONFIDENTIAL DWN BY: PD JGM UNPUBLISHED WORK 2008 CHKD BY: DECEUNINCK NORTH AMERICA DWG NO: PD-006 THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS.
28 UNLESS OTHERWISE SPECIFIED CONFIDENTIAL DIM ARE IN INCHES TOL ON ANGLES 1 DRAWN BY: UNPUBLISHED WORK ' 2 PL: 0.010" 3 PL: 0.005" DECEUNINCK NORTH AMERICA INTERPRET DIM AND TOL PER ASME Y14.5M THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY THIRD ANGLE PROJECTION OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS. DESIGN BY: FILENAME: NAME: 351 NORTH GARVER ROAD MONROE, OHIO NORTH AMERICA SIZE DWG. NO: REV. SCALE: (LBS/FT.) SHEET: CAD MAINTAINED. CHANGES SHALL BE INCORPORATED BY THE DESIGN ACTIVITY. REVISION HISTORY REV DESCRIPTION DATE APPROVED L REMOVED INTERIOR WSS DIMENSIONS 10/05/26 BWB $PLOTDATE$ R S K.020 A U Q V J A AD WALL THICKNESS AB M X P AE G AF $USER$ KEY PRODUCT CHARACTERISTICS GAUGE AG G DIMENSION AN Z A J DIMENSION AJ AH Q DIMENSION V DIMENSION AL A AM.020 A AI Z GAUGE _ AH DIMENSION AK AN DIMENSION CTC 05/03/ CTC NOTES: 05/03/30 1. STD00013 STRAIGHTNESS CLASS A AND LENGTH TOLERANCES APPLY 2. INTERPRET ALL TOLERANCE APPLICATIONS PER STD0013 B A MAIN FRAME - PD 3. UNSPECIFIED EXTERNAL RADII =.XXX / C 4. UNSPECIFIED INTERNAL RADII =.XXX / D 5. UNSPECIFIED EXTERNAL WALL THICKNESS =.XXX +/- 10% 6. UNSPECIFIED INTERNAL WALL THICKNESS =.XXX +/- 20% E F $FILE NAME$ B _SH 1 : OF 1 L $FILEL$
29 UNLESS OTHERWISE SPECIFIED CONFIDENTIAL DIM ARE IN INCHES TOL ON ANGLES 1 DRAWN BY: UNPUBLISHED WORK ' 2 PL: 0.010" 3 PL: 0.005" DECEUNINCK NORTH AMERICA INTERPRET DIM AND TOL PER ASME Y14.5M THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY THIRD ANGLE PROJECTION OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS. DESIGN BY: FILENAME: NAME: 351 NORTH GARVER ROAD MONROE, OHIO NORTH AMERICA SIZE DWG. NO: REV. SCALE: (LBS/FT.) SHEET: CAD MAINTAINED. CHANGES SHALL BE INCORPORATED BY THE DESIGN ACTIVITY. REVISION HISTORY REV DESCRIPTION DATE APPROVED F KPC 09/11/04 BWB $PLOTDATE$ KEY PRODUCT CHARACTERISTICS H DIMENSION M A S M N DIMENSION DIMENSION N T DIMENSION K L USE GAUGES I-1 I-2B USE GAUGES I-1 O I-2B P Y Q USE GAUGE I-1 I R.020 J T H G.020 $USER$ A V.020 WALL THICKNESS A W X RJC 00/10/ RJC NOTES: 00/10/20 1. STD00013 STRAIGHTNESS CLASS A AND LENGTH TOLERANCES APPLY 2. INTERPRET ALL TOLERANCE APPLICATIONS PER STD0013 B 3. UNSPECIFIED EXTERNAL RADII =.XXX / C 4. UNSPECIFIED INTERNAL RADII =.XXX / D 5. UNSPECIFIED EXTERNAL WALL THICKNESS =.XXX +/- 10% E 6. UNSPECIFIED INTERNAL WALL THICKNESS =.XXX +/- 20% F A $FILE NAME$ B SILL FRAME - PD _SH 1 : OF 1 F $FILEL$
30 UNLESS OTHERWISE SPECIFIED CONFIDENTIAL DIM ARE IN INCHES TOL ON ANGLES 1 DRAWN BY: UNPUBLISHED WORK ' 2 PL: 0.010" 3 PL: 0.005" DECEUNINCK NORTH AMERICA INTERPRET DIM AND TOL PER ASME Y14.5M THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY THIRD ANGLE PROJECTION OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS. DESIGN BY: FILENAME: NAME: 351 NORTH GARVER ROAD MONROE, OHIO NORTH AMERICA SIZE DWG. NO: REV. SCALE: (LBS/FT.) SHEET: CAD MAINTAINED. CHANGES SHALL BE INCORPORATED BY THE DESIGN ACTIVITY. REVISION HISTORY REV DESCRIPTION DATE APPROVED H ADDED GAUGE 09/05/26 BWB $PLOTDATE$ SCALE 1: 1 I.010 A R Q.020 A J KEY PRODUCT CHARACTERISTICS G FRAME DIMENSION H FRAME DIMENSION I FRAME DIMENSION H DNA G U L K M $USER$ J FRAME DIMENSION L FRAME DIMENSION WALL THICKNESS.020 A T A S O N SJD 01/06/ SJD NOTES: 01/06/21 1. STD00013 STRAIGHTNESS CLASS B AND LENGTH TOLERANCES APPLY 2. INTERPRET ALL TOLERANCE APPLICATIONS PER STD0013 B 3. UNSPECIFIED EXTERNAL RADII =.XXX / C 4. UNSPECIFIED INTERNAL RADII =.XXX / D 5. UNSPECIFIED EXTERNAL WALL THICKNESS =.XXX +/- 10% E 6. UNSPECIFIED INTERNAL WALL THICKNESS =.XXX +/- 20% F A $FILE NAME$ B MAIN SASH - PD _SH 2 : OF 1 G $FILEL$
31 UNLESS OTHERWISE SPECIFIED CONFIDENTIAL DIM ARE IN INCHES TOL ON ANGLES 1 DRAWN BY: UNPUBLISHED WORK ' 2 PL: 0.010" 3 PL: 0.005" DECEUNINCK NORTH AMERICA INTERPRET DIM AND TOL PER ASME Y14.5M THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DO NOT COPY THIRD ANGLE PROJECTION OR DISCLOSE THIS INFORMATION WITHOUT THE EXPRESS WRITTEN CONSENT OF DECEUNINCK NORTH AMERICA. DECEUNINCK NORTH AMERICA RESERVES THE RIGHT TO CHANGE THIS DRAWING AND ANY ASSOCIATED DOCUMENTS. DESIGN BY: FILENAME: NAME: 351 NORTH GARVER ROAD MONROE, OHIO NORTH AMERICA SIZE DWG. NO: REV. SCALE: (LBS/FT.) SHEET: CAD MAINTAINED. CHANGES SHALL BE INCORPORATED BY THE DESIGN ACTIVITY. REVISION HISTORY REV DESCRIPTION DATE APPROVED B GDT-3 07/12/04 DBF 8/8/2008 C TOLERANCE CHANGE, WAS +/ /08/06 JGM SCALE 1 : 1 WALL THICKNESS G C = = H J C (.298 ) (1.051 ) usjgm I C (2.128 ) NOTES: 1. STD00013 STRAIGHTNESS CLASS E AND LENGTH TOLERANCES APPLY 2. INTERPRET ALL TOLERANCE APPLICATIONS PER STD0013 B 3. UNSPECIFIED EXTERNAL RADII =.XXX / C 4. UNSPECIFIED INTERNAL RADII =.XXX / D 5. UNSPECIFIED EXTERNAL WALL THICKNESS =.XXX +/- 10% E 6. UNSPECIFIED INTERNAL WALL THICKNESS =.XXX +/- 20% F A 2008 CTC 05/11/14 CTC 05/11/ DGN B FRAME ADAPTOR _SH 2 : C \\monsrv01\dectech$\data\dgn\73961.dgn
NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. (Revised) Rendered to: SPECIALTY WHOLESALE SUPPLY
NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT (Revised) Rendered to: SPECIALTY WHOLESALE SUPPLY SERIES/MODEL: 4000 / 4500 DuraGard XT Double Hung Report Number: Original
More informationNFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: PARAMOUNT WINDOWS
Architectural Testing NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: PARAMOUNT WINDOWS SERIES/MODEL: 6700/ 6750/ 7700/ 8700/ 8750 Report Number: Report Date:
More informationNFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: EARTHWISE GROUP, L.L.C.
Architectural Testing NFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: EARTHWISE GROUP, L.L.C. SERIES/MODEL: 143.095 SH 145.095 SH 143.095 SH Common Head Baseline
More informationNFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: EARTHWISE GROUP, L.L.C. SERIES/MODEL: SS 145.
Architectural Testing NFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: EARTHWISE GROUP, L.L.C. SERIES/MODEL: 143.095 SS 145.095 SS Baseline Product for Validation
More informationNFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: EARTHWISE GROUP, L.L.C.
Architectural Testing NFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: EARTHWISE GROUP, L.L.C. SERIES/MODEL: 143.095 DH 143.195 DH 145.095 DH 145.195 DH Baseline
More informationNFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: EARTHWISE GROUP, L.L.C.
Architectural Testing NFRC U-FACTOR, SHGC / VT, CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: EARTHWISE GROUP, L.L.C. SERIES/MODEL: 143.191 Casement / Awning / Fixed Baseline Product
More informationNFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: CR LAURENCE CO., INC.
FRC U-FACTOR, SHGC, VT, & CODESATIO RESISTACE COMPUTER SIMULATIO REPORT Rendered to: CR LAURECE CO., IC. SERIES/MODEL: StormWall XL Curtain Wall Report umber: Report Date: 10/14/16 FRC U-FACTOR, SHGC,
More informationNFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT. Rendered to: PARAMOUNT WINDOWS CORPORATION
Architectural Testing NFRC U-FACTOR, SHGC, VT, & CONDENSATION RESISTANCE COMPUTER SIMULATION REPORT Rendered to: PARAMOUNT WINDOWS CORPORATION SERIES/MODEL: ECO-View 6100/7100 Report Number: B6000.01-301-45
More informationU-Factor, Solar Heat Gain Coefficient, Visible Transmittance and Condensation Resistance Calculation Report
U-Factor, Solar Heat Gain Coefficient, Visible Transmittance and Condensation Resistance Calculation Report REPORT NO: NCTL-110-16086-01 SIMULATION DATE: 08/30/13 REPORT DATE: 08/30/13 Client: Product
More informationU-Factor, Solar Heat Gain Coefficient, Visible Transmittance and Condensation Resistance Calculation Report
U-Factor, Solar Heat Gain Coefficient, Visible Transmittance and Condensation Resistance Calculation Report REPORT NO: NCTL-110-14975-01 SIMULATION DATE: 03/25/13 REPORT DATE: 03/25/13 Client: Product
More informationAAMA THERMAL PERFORMANCE REPORT. Rendered to: TORO ALUMINUM. SERIES/MODEL: Commdoor 225 Awning (Project Out) TYPE: Projecting, Awning
Architectural Testing AAMA 507-12 THERMAL PERFORMANCE REPORT Rendered to: TORO ALUMINUM SERIES/MODEL: Commdoor 225 Awning (Project Out) TYPE: Projecting, Awning Report No: Report Date: 130 Derry Court
More informationAAMA THERMAL PERFORMANCE REPORT (Revised) Rendered to: UNITED STATES ALUMINUM
AAMA 507-07 THERMAL PERFORMANCE REPORT (Revised) Rendered to: UNITED STATES ALUMINUM SERIES/MODEL: 7600 Projected Vent TYPE: Projecting (Awning - Single) Report No: Original Report Date: Revised Report
More informationAAMA THERMAL PERFORMANCE REPORT. Rendered to: UNITED STATES ALUMINUM. SERIES/MODEL: 3150 Curtain Wall TYPE: Glazed Wall System
AAMA 507-07 THERMAL PERFORMANCE REPORT Rendered to: UNITED STATES ALUMINUM SERIES/MODEL: 3150 Curtain Wall TYPE: Glazed Wall System Report No: Report Date: 08/22/08 130 Derry Court York, PA 17406-8405
More informationAAMA THERMAL PERFORMANCE REPORT. Rendered to: TUBELITE, INC. SERIES/MODEL: 200 Series Curtainwall (E2297) TYPE: Glazed Wall System
AAMA 507-03 THERMAL PERFORMANCE REPORT Rendered to: TUBELITE, INC. SERIES/MODEL: 200 Series Curtainwall (E2297) TYPE: Glazed Wall System Report No: Report Date: 05/23/07 130 Derry Court York, PA 17406-8405
More informationAAMA THERMAL PERFORMANCE REPORT. Rendered to: US ALUMINUM INC., DIVISION OF CR LAURENCE CO., INC.
Archi t ectural Testing THERMAL PERFORMANCE REPORT Rendered to: US ALUMINUM INC., DIVISION OF CR LAURENCE CO., INC. SERIES/MODEL: S80 Bi-Fold Door (1" Dual Glazed) TYPE: Swinging Door - Double Report No:
More informationAAMA/WDMA/CSA 101/I.S.2/A TEST REPORT. Rendered to: MASTER WINDOW SYSTEMS, INC.
AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT Rendered to: MASTER WINDOW SYSTEMS, INC. SERIES/MODEL: Master 2000 Double Hung Window PRODUCT TYPE: PVC Double Hung Window Summary of Results Title Test Specimen
More informationTEST REPORT. Report No.: G Rendered to: VELUX America LLC Greenwood, South Carolina
TEST REPORT Report No.: G4212.01-109-44 Rendered to: VELUX America LLC Greenwood, South Carolina PRODUCT TYPE: Skylight with Curb SERIES/MODEL: Specials Dome Skylight 0.118 thickness PC smooth/0.118 thickness
More informationCOMPUTER SIMULATION U-FACTOR, SHGC, VT PERFORMANCE EVALUATION OF FIXED WINDOW 3000 SERIES LOW PROFILE FIXED. Dominion Doors & Windows Ltd.
COMPUTER SIMULATION U-FACTOR, SHGC, VT PERFORMANCE EVALUATION OF FIXED WINDOW 3000 SERIES LOW PROFILE FIXED FOR Dominion Doors & Windows Ltd. IN ACCORDANCE WITH: CAN/CSA A440.2-14 Report to: Dominion Doors
More informationCOMPUTER SIMULATION U-FACTOR, SHGC, VT PERFORMANCE EVALUATION OF FIXED WINDOW 3000 SERIES CASEMENT WINDOW. Dominion Doors & Windows Ltd.
COMPUTER SIMULATION U-FACTOR, SHGC, VT PERFORMANCE EVALUATION OF FIXED WINDOW 3000 SERIES CASEMENT WINDOW FOR Dominion Doors & Windows Ltd. IN ACCORDANCE WITH: CAN/CSA A440.2-14 Report to: Dominion Doors
More informationASTM E 1886 and ASTM E 1996 TEST REPORT. Report No.: A Rendered to: GLASSCRAFT DOOR COMPANY Houston, Texas
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Report No.: A6457.01 801 18 Rendered to: GLASSCRAFT DOOR COMPANY Houston, Texas PRODUCT TYPE: In Swing Fiberglass Door with Side Lites SERIES/MODEL:
More informationASTM E 1886 and ASTM E 1996 TEST REPORT. Report No.: A Rendered to: GLASSCRAFT DOOR COMPANY Houston, Texas
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Report No.: A6458.01 801 18 Rendered to: GLASSCRAFT DOOR COMPANY Houston, Texas PRODUCT TYPE: Fiberglass In Swing Glazed Double Doors SERIES/MODEL:
More informationASTM E 1886 and ASTM E 1996 TEST REPORT. Report No.: A Rendered to: GLASSCRAFT DOOR COMPANY Houston, Texas
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Report No.: A6839.01 801 18 Rendered to: GLASSCRAFT DOOR COMPANY Houston, Texas PRODUCT TYPE: In Swing Fiberglass Double Doors with Speak Easy
More informationNotice of Product Certification Authorization
Keystone Certifications, Inc. 564 Old York Road, Suite 5 Etters, PA 17319 / Phone 717-932-8500 Notice of Product Certification Authorization National Fenestration Rating Council Issued To: Manufacturer:
More informationCREEP PERFORMANCE TEST REPORT. Rendered to: TREX COMPANY LLC. Seclusions Composite Privacy Fence System TYPE: Composite Fence System
Architectural Testing CREEP PERFORMANCE TEST REPORT Rendered to: TREX COMPANY LLC Seclusions Composite Privacy Fence System TYPE: Composite Fence System Report No.: Report Date: Expiration Date: 130 Derry
More information8400 SERIES THERMAL PERFORMANCE CHART
Page 1 of 5 Pages LE-CL WCW-M-30-00386-00001 0.32 3.13 0.23 0.45 WCW-M-30-00386-00002 0.32 3.13 0.21 0.40 DS-LAMI (PVB030) LE-CL (Lami) WCW-M-30-00388-00001 0.32 3.13 0.23 0.44 WCW-M-30-00388-00002 0.32
More informationSINGLE SLIDING WINDOW 1000 SERIES 4-1/2" FRAME SINGLE SLIDER LIFT OUT
PERFORMANCE EVALUATION OF SINGLE SLIDING WINDOW 1000 SERIES 4-1/2" FRAME SINGLE SLIDER LIFT OUT For Dominion Doors & Windows Ltd. IN ACCORDANCE WITH: AAMA/WDMA/CSA 101/I.S.2/A440-11 AND A440S1-17 Report
More informationSRD Design CORPORATION. Fenestration Specialists!
SRD Design CORPORATION Fenestration Specialists! Series 5000 By Champion Window & Door Syosset, New York Design by: SRD Design 2002 SRD Design CORPORATION ENGINEERING ENGINEERING SPECIALISTS DIVERSITY
More informationTEST REPORT. Report No.: G Rendered to: SKYCO SKYLIGHTS Costa Mesa, California
TEST REPORT Report No.: G1418.01-301-44 Rendered to: SKYCO SKYLIGHTS Costa Mesa, California PRODUCT TYPE: Fall Protection Security Bars SERIES/MODEL: FSB-1A/FSB-10A/FSB-1/FSB-10 SPECIFICATION: Occupational
More informationCONSTRUCTION CONSULTING LABORATORY, INTERNATIONAL
TEST REPORT: SERIES 8220 ALUMINUM SINGLE HUNG WINDOW Prepared for: 5625 E. Firestone Boulevard South Gate, CA 90280 1601 Luna Road S-UNITED, INC. Office: (972) 242-0556 Carrollton, Texas 75006 A Quality
More informationTEST REPORT. Rendered to: HOMELAND VINYL PRODUCTS, INC. For: PVC Guardrail System Utilizing New Nylon/PVC Rail Mounting Bracket
TEST REPORT Rendered to: HOMELAND VINYL PRODUCTS, INC. For: PVC Guardrail System Utilizing New Nylon/PVC Rail Mounting Bracket Report No: Report Date: 10/31/12 130 Derry Court York, PA 17406-8405 phone:
More informationDouble Hung. Power Lift 28,000 Constant Force
Insul-Tec Double Hung Stylish Full 3¼ Depth Welded Mainframe with beveled colonial exterior curves that are not only beautiful, but also allow for maximum weld surface resulting in outstanding strength
More informationPERFORMANCE TEST REPORT. Rendered to: AIR VENT, INC. SERIES/MODEL: Hip Ridge Vent PRODUCT TYPE: Ridge Vent
Architectural Testing PERFORMANCE TEST REPORT Rendered to: AIR VENT, INC. SERIES/MODEL: Hip Ridge Vent PRODUCT TYPE: Ridge Vent This report contains in its entirety: Cover Page: 1 page Report Body: 6 pages
More informationLUXURY SLIDING PATIO & SWINGING FRENCH DOORS
M A L I B U LUXURY SLIDING PATIO & SWINGING FRENCH DOORS M A L I B U THE BEAUTY OF YOUR HOME Malibu Sliding Patio and Swinging French Doors enhance the beauty of your home, both inside and out. Each door
More informationGuide Specification SECTION VINYL WINDOWS
February 2018 3948 Townsfair Way, Suite 200 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com Email archdetails@simonton.com Guide Specification Specifier Notes: This guide specification
More informationSize and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data. Detailed Product Description
SCTIN DIRCTRY Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information published in this document
More informationSliding Patio Doors Builders Vinyl
TABLE OF CONTENTS Specifications... 7-2 QuickSpecGuide... 7-3 Elevations/Sizes: 1/4 Scale 2-Panel... 7-4 3-Panel... 7-5 2-Panel withtransom... 7-6 Sidelite... 7-8 Transom... 7-9 3-PanelTransom... 7-10
More informationProduct Guide Specification
July 2013 3948 Townsfair Way, Suite 200 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com E-Mail archdetails@simonton.com Product Guide Specification Specifier Notes: This product guide
More information3948 Townsfair Way, Suite 200 July 2013 Columbus, Ohio Toll Free Website
3948 Townsfair Way, Suite 200 July 2013 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com E-Mail archdetails@simonton.com Product Guide Specification Specifier Notes: This product guide
More informationNew $1500 Stimulus Plan Tax Credit
New $1500 Stimulus Plan Tax Credit Eagle windows and doors can help maximize your home s comfort and minimize your energy bills. And, if you buy them now, you may qualify for up to a $1,500 credit on your
More informationSize and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data. Detailed Product Description
ncompass by Pella SCTION DIRCTORY SINGL-HUNG Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information
More informationSIZE AND PERFORMANCE SUMMARY GLAZING PERFORMANCE GRILLE PROFILES AND PATTERNS SIZE TABLES DESIGN DATA DETAILED PRODUCT DESCRIPTION CROSS SECTIONS
SECTION DIRECTORY SIZE AND PERFORMANCE SUMMARY GLAZING PERFORMANCE GRILLE PROFILES AND PATTERNS SIZE TABLES DESIGN DATA DETAILED PRODUCT DESCRIPTION CROSS SECTIONS The information published in this document
More informationHURRICANESHIELD IMPACT-RESISTANT GLASS SECTION DIRECTORY. Size and performance summary. Glazing performance. Grille profiles and patterns.
SECTIN DIRECTRY Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information published in this document
More informationPerformance Data and Comparisons
Performance Data and Comparisons The performance of Cardinal s LoE products are shown on the attached Insulating Glass Performance Comparison charts. The following products and combination of products
More informationBS EN :2006. Windows and doors Product standard, performance characteristics. A Report To: Mila Hardware Ltd. Document Reference:
Exova Warringtonapt Key Industrial Park Fernside Road Willenhall West Midlands WV13 3YA T : +44 (0) 1902 722 122 F : +44 (0) 1902 727 242 E : willenhall@exova.com W: www.exova.com BS EN 14351-1:2006 Test
More informationPella Impervia 350 Series Vinyl Awning Windows and Sliding Patio Doors
Pella Impervia 350 Series Vinyl Awning Windows and Sliding Patio Doors Pella 350 Series premium vinyl windows and patio doors are available in a variety of frame types to help ensure a smooth installation
More informationGeneral Information SECTION DIRECTORY
SECTION DIRECTORY General Information Product Summary... V-AW-2 Product Selection Guide... V-AW-3 Size and Performance Data... V-AW-3 Features and Options... V-AW-3 Sound Transmission Class and Outdoor-Indoor
More informationCHAPTER 3 INTEGRITY WOOD ULTREX DOUBLE HUNG
CHAPTER 3 INTEGRITY WOOD ULTREX DOUBLE HUNG Specifications / NFRC Values... 3.2 Egress, Lite and Vent Measurements... 3.3 Egress, Lite and Vent Measurements / Abbreviations... 3.4 Sizing Guidelines / Measurement
More informationProduct Guide Specification
October 2011 3948 Townsfair Way, Suite 200 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com E-Mail archdetails@simonton.com Product Guide Specification Specifier Notes: This product
More informationSize and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data. Detailed Product Description
SECTIN DIRECTRY Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information published in this document
More informationBS EN ISO :2006
Exova (UK) Ltd Key Industrial Park Fernside Road Willenhall West Midlands WV13 3YA T : +44 (0) 1902 722 122 F : +44 (0) 1902 727 242 E : willenhall@exova.com W: www.exova.com BS EN ISO 10077-1:2006 Calculation
More informationAAMA/WDMA/CSA 101/I.S.2/A440-08
PERFORMANCE TESTS IN ACCORDANCE WITH AAMA/WDMA/CSA 101/I.S.2/A440-08 Product Manufacturer: Report No.: AI-04016-U1 Rev.1 ACRYLON PLASTICS 122 PAQUIN ROAD WINNIPEG, MANITOBA R2J 3V4 204-669-2345 Report
More informationSize and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data. Detailed Product Description
SCTION DIRCTORY Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information published in this document
More informationSIZE AND PERFORMANCE SUMMARY GLAZING PERFORMANCE GRILLE PROFILES AND PATTERNS SIZE TABLES DESIGN DATA DETAILED PRODUCT DESCRIPTION CROSS SECTIONS
SECTIN DIRECTRY SIZE AND PERFRMANCE SUMMARY GLAZING PERFRMANCE GRILLE PRFILES AND PATTERNS SIZE TABLES DESIGN DATA DETAILED PRDUCT DESCRIPTIN CRSS SECTINS The information published in this document is
More informationSolarban 70XL and Solarban 70XLVT Coated Glass Technical Considerations and Guidelines
General Vitro (formerly PPG Industries) Solarban 70XL and Solarban 70XLVT coated glass are another innovative improvement in energy efficient coated glass technology from Vitro Solarban 70XL low emissivity
More informationAAMA/WDMA/CSA 101/I.S.2/A440-08
PERFORMANCE TESTS IN ACCORDANCE WITH AAMA/WDMA/CSA 101/I.S.2/A440-08 Product Manufacturer: Report No.: AI-04016-T1 Rev.1 ACRYLON PLASTICS 122 PAQUIN ROAD WINNIPEG, MANITOBA R2J 3V4 204-669-2345 Report
More informationyour vision, our windows
your vision, our windows WHY FIBERGLASS? ENERGY EFFICIENCY ALUMINUM 500x lower thermal conductivity than aluminum, so it doesn t allow heat or cold from the outside into your home. Fiberglass uses 78%
More informationCALIBRATION REPORT. Rendered to: United States Aluminum Corp. LOCATION: Waxahachie, Texas
CALIBRATION REPORT Rendered to: United States Aluminum Corp. LOCATION: Waxahachie, Texas Report No.: 79241.01-801-47 Calibration Date: 12/14/07 Report Date: 03/20/08 2865 Market Loop Southlake, Texas 76092
More informationSize and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data. Detailed Product Description
SECTON DRECTORY Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information published in this document
More informationArchitect Series Traditional
SECTION DIRECTORY Architect Series Traditional Product Selection Guide Size and Performance Data...W-HG-2 STC/OITC...W-HG-2 Features and Options...W-HG-3 Combination Assemblies...W-HG-4 Glazing Performance...W-HG-6
More informationNFPA 285 TEST REPORT. Report No.: H Test Date: June 1, Rendered to: ARCONIC ARCHITECTURAL PRODUCTS Eastman, Georgia
NFPA 285 TEST REPORT Report No.: H1152.01-121-24 Test Date: June 1, 2017 Rendered to: ARCONIC ARCHITECTURAL PRODUCTS Eastman, Georgia WALL SYSTEM: Exterior Non-loadbearing Wall Assembly COMBUSTIBLE COMPONENTS:
More informationDF COLLECTION. Architectural Detail Guide Hybrid Awning Window DF 3113 TABLE OF CONTENTS
TABLE OF CONTENTS Specifications... 1-2 Quick Spec Guide... 1-3 Clear Opening and Daylight Specifications... 1-5 General Information Multiple Assemblies... 1-6 Handing and Operation... 1-7 Elevation Drawing
More information2300/2320. MORTISE LOCKS AND HANDLESET ACCESSORIES (Keepers, Spacers, Adapters and Bumpers)
HANDLES & LOCKSETS MORTISE LOCK APPLICATIONS 2300/2320 Truth Hardware realizes that each profile in the marketplace may require its own particular hardware component due to the variety of mounting applications
More informationDOUBLE HUNG. Power Lift 28,000 Constant Force
INSUL-TEC DOUBLE HUNG The secret behind this window s performance is its exceptionally low air infiltration ratings which can lower the energy consumption of a typical home by 25 40%. This unique feature,
More informationLifestyle Series Casement
Product Selection Guide Size and Performance Data...LS-CM-2 Features and Options...LS-CM-3 Combination Assemblies...LS-CM-4 Glazing Performance Dual-Pane...LS-CM-8 Triple-Pane... LS-CM-10 Grille Types
More informationProduct Selection Guide Size and Performance Data...W-HG-2 Features and Options...W-HG-3 Combination Assemblies...W-HG-4 Glazing Performance...
SECTION DIRECTORY Product Selection Guide Size and Performance Data...W-HG-2 Features and Options...W-HG-3 Combination Assemblies...W-HG-4 Glazing Performance...W-HG-6 Grille Types Grille Profiles...W-HG-10
More informationVisions 3000 Series 924 Parts Catalog
3000 Series Visions 3000 Series 924 Parts Catalog #1218583 FOR PRODUCT PRODUCED AFTER 4/07 Casement Casement Awning awning French Casement french casement Visions Windows and Doors 880 South View Drive
More informationWeather Shield Thermal Performance Criteria
Weather Shield Thermal Perfmance Criteria As a proud ENERGY STAR partner, we ensure our products are rated, certifi ed and labeled f and by the National Fenestration Council (NFRC). The 2010 ENERGY STAR
More informationPella 450 Series. Size and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data
SECTION DIRECTORY Pella 450 Series Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information published
More informationVINYL WINDOWS & DOORS
VINYL WINDOWS & DOORS By FLEETWOOD FLEETWOOD FleetwoodUSA.com HIGH-PERFORMANCE VINYL WINDOWS Energy Efficient Means Smaller Energy Bills Because vinyl windows and doors keep cold air out in winter and
More informationSliding Patio Doors Flat Casing Vinyl
TABLE OF CONTENTS Specifications... 5-2 QuickSpecGuide... 5-3 Elevations/Sizes: 1/4 Scale 2-PanelSlidingPatioDoors... 5-4 2-PanelSlidingPatioDoorswithTransoms... 5-5 Transoms... 5-7 Sidelights... 5-9 SectionDetails...
More informationArchitect Series Traditional
SECTION DIRECTORY Product Selection Guide Size and Performance Data... OSBF-2 Glazing Performance... OSBF-3 Grille Types... OSBF-7 Design Data Vent... OSBF-11 Detailed Product Descriptions... OSBF-14 Unit
More information6100 SERIES SINGLE HUNG
STORMSTRONG IMPACT RESISTANT 6100 SERIES SINGLE HUNG 1. 8 0 0. 3 2 7. 3 0 8 6 w w w. C W S. c c STORMSTRONG Impact Resistant Single Hung Windows Storm Strong 6100 Series Single Hung 1-1/2 pre-punched Nail
More informationManufacturer s Certification Ply Gem Replacement Windows
Manufacturer s Certification Ply Gem Replacement Windows Ply Gem Windows, located at 4415 Pheasant Ridge Road, Suite 300, Roanoke, Virginia 24014, manufactures certain Premium and Pro Series exterior windows
More informationV3 Series Awning Windows (2011 to Present)
What s in This Section Standard and Custom Windows...................................... Page 3 Parts Illustration........................................................... 3 Options- Exterior..................................................
More information100 Series Awning Windows (2008 to Present)
100 Series Awning Windows (2008 to Present) CCParts Catalog Main Menu Section TOC Search What s in This Section Standard and Custom Windows...................................... Page 3 Parts Illustration...........................................................
More informationArchitectural Manual. Vinyl Windows & Patio Doors
Architectural Manual Vinyl Windows & Patio Doors Style Line Series Vinyl Windows & Patio Doors Instructions on how to use this manual: This document has been designed for easy navigation and to quickly
More information2000T TERRACE DOOR. Features
AUGUST, 0 000T TERRACE DOOR FEATURES Features Performance class and grade: Single: AW-PG90-ATD Pairs: AW-PG45/65-ATD Inswing or outswing -/4" deep door rails and stiles Mitered door and frame corners Heavy
More informationAIR-INS inc. 1320, boul. Lionel-Boulet, Varennes (Québec) J3X 1P7 Tél. : (450) Fax : (450)
1320, boul. Lionel-Boulet, Varennes (Québec) J3X 1P7 Tél. : (450) 652-0838 Fax : (450) 652-7588 info@air-ins.com FORCED-ENTRY RESISTANCE TESTS AS PER THE ASTM F476-84(2002) TESTING PROCEDURE ON AN ENTRANCE
More informationSliding Windows Brickmould Vinyl
TABL OF CONTNTS Specifications........................................................... 6-2 Quick Spec Guide....................................................... 6-3 levations/sizes: 1/4 Scale 2-Wide
More informationSpecifications... Quick Spec Guide...
TABLE OF CONTENTS Specifications........................................... Quick Spec Guide....................................... Elevations/Sizes: 1/4" Scale Full Awning Units..................................
More information100 Series Awning Windows (2008 to Present)
100 Series Awning Windows (2008 to Present) CCParts Catalog Main Menu Section TOC Search What s in This Section Standard and Custom Windows...................................... Page 3 Parts Illustration...........................................................
More information350/500 Tuffline TM Entrances 1
JANUARY, 2017 350/500 Tuffline TM Entrances 1 FEATURES Features 350 Tuffline TM has 3-1/2" (88.9) vertical stile, 3-3/8" (85.8) top and 6-3/4" (171.5) bottom rail 500 Tuffline TM has 5" (127) vertical
More informationVista Series Vinyl Windows & Doors
Vista Series Vinyl Windows & Doors Options maximize COmFORt, beauty & StyLE Vista PLUS vs. Vista Windows SEE the DIFFERENCE & ChOOSE with CONFIDENCE LE3 STC SPL CC LowE3 performance glass with Argon gas
More informationAmbassador ALUMINUM WINDOWS & DOORS FOR ALL SEASONS
Ambassador ALUMINUM WINDOWS & DOORS FOR ALL SEASONS THE REVOLUTION IS HERE. I N T E R N AT I O N A L W I N D O W CO R P O R AT I O N About Ambassador The name says it all. Representing International Window
More informationGOLD LABEL CERTIFICATION
2 Great Windows You Can See The Difference! Full Head Bevel Drip Cap These days, with so many choices, deciding on a window can be challenging. So we ve made it easy for you! We feature two extremely energy
More informationWarranty, Parts & Install Info 1. Series 4600 Double Hung Windows 2. Series 4710 Casement Windows 3. Series 9000 Sliding Patio Door 4
Warranty, Parts & Install Info 1 Series 4600 Double Hung Windows 2 Series 4710 Casement Windows 3 Series 9000 Sliding Patio Door 4 Series 9200 Inswing Doors 5 Series 9300 Outswing Doors 6 Series 9380 Outswing
More informationVisions 2000 Double Hung Tilt Window Parts Reference Catalog
Visions 2000 Double Hung Tilt Window Parts Reference Catalog (Includes Parts and Information for Double Hung Tilt Oriel and Double Hung Tilt Picture) #010636 (Revised 01/03) Weather Shield Mfg., Inc. Medford,
More informationPella 250 Series. Size and performance summary. Glazing performance. Grille profiles and patterns. Size tables. Design Data
SCTIN DIRCTRY Pella 250 Series DUBL-HUNG Size and performance summary Glazing performance Grille profiles and patterns Size tables Design Data Detailed Product Description Cross sections The information
More information5400 Armor Max Plus Windows Maximum Impact Protection
5400 Armor Max Plus Windows Maximum Impact Protection Exceptional hurricane protection, beauty, energy efficiency, security, safety and sound reduction. America s Toughest, Prettiest and Most Versatile
More informationAriel Sliding Patio Doors
Ariel Sliding Patio Doors REPLACEMENT PARTS CATALOG 2-Panel Unit... 2 3-Panel Unit... 4 4-Panel Unit... 6 Screens... Back Cover Unit Sizes... Back Cover Notice: The replacement parts shown herein are for
More information100 Series Awning Windows (2008 to Present)
100 Series Awning Windows (2008 to Present) CCParts Catalog Main Menu Section TOC Search What s in This Section Standard and Custom Windows...................................... Page 3 Parts Illustration...........................................................
More informationAAMA/WDMA/CSA 101/I.S.2/A NAFS North American Fenestration Standard/Specification for windows, doors, and skylights
AAMA/WDMA/CSA 101/I.S.2/A440-08 NAFS North American Fenestration Standard/Specification for windows, doors, and skylights Registered trade-mark of American Architectural Manufacturers Association Registered
More informationArchitect Series Designer Series Pella ProLine. Architect Series...AW-1 Designer Series...AW-2 Pella ProLine...AW-2
SECTION DIRECTORY Brand Directory Architect Series...AW-1 Designer Series...AW-2 Pella ProLine...AW-2 General Information Brand Summary...AW-3 Product Selection Guide Size and Performance Data...AW-4 Features
More informationU.S. ALUMINUM 3025 SERIES SLIDING DOORS
U.S. ALUMINUM 3025 SERIES SLIDING S 83 83 1/8" 40" 72" 71 1.1 1.5 1.3 1.7 1.8 1.9 (BEYOND) TESTED TO AAMA LC25 ACCOMODATES 1" (25mm) AND 1 (32mm) GLAZING OPTIONAL THERMALLY BROKEN HEAD AND JAMB CHANNELS
More informationSIZE AND PERFORMANCE SUMMARY GLAZING PERFORMANCE GRILLE PROFILES AND PATTERNS SIZE TABLES DESIGN DATA DETAILED PRODUCT DESCRIPTION CROSS SECTIONS
SCTION DIRCTORY DOUBL-HUNG SIZ AND PRFORMANC SUMMARY GLAZING PRFORMANC GRILL PROFILS AND PATTRNS SIZ TABLS DSIGN DATA DTAILD PRODUCT DSCRIPTION CROSS SCTIONS The information published in this document
More informationBasic steps for installing the AmeriGlide Express Dumbwaiter
Basic steps for installing the AmeriGlide Express Dumbwaiter 1. Remove Shroud. 2. Mount lower section of Track and Unit to hoistway wall and Brackets. 3. Remove Shipping Bracket from Top of Car. 4. Install
More informationcero by NanaWall The Minimal Framed Large Panel Sliding Glass Wall
INTRODUCTION CERO BY NANAWALL cero by NanaWall The Minimal Framed Large Panel Sliding Glass Wall cero is the minimal framed large panel sliding glass wall by NanaWall Systems. Simple in form yet engineered
More informationSingle-Hung Windows Premium Atlantic Vinyl
TABL OF CONTNTS Specifications... 3-2 QuickSpecGuide... 3-3 levations/sizes: 1/4 Scale Single-Hung... 3-4 ImpactSingle-Hung... 3-10 GlazingOptions: Scale... 3-11 Grille Patterns... 3-12 SectionDetails:
More informationSentinel Single Hung Window 110
Available Finishes: White & Bronze Standard Glass Colors: Clear, Gray, Dark Gray (Turtle Code), Bronze, Solexia Green, Azuria Blue, White Interlayer, Mist (Pattern 62), Rain Sentinel Single Hung Window
More informationAluminum Sliding Glass Corner Meet Door Series SGD680 Product Specifications
Product Specifications Monolithic glazing does not provide hurricane protection Specifications: Door members are extruded from a minimum of 6063-T6 aluminum alloy (except where noted) Finish is white or
More information