DEPARTMENT OF THE ARMY TECHNICAL MANUAL DIRECT AND GENERAL SUPPORT AND DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST

Transcription

1 TM P DEPARTMENT OF THE ARMY TECHNICAL MANUAL DIRECT AND GENERAL SUPPORT AND DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST WELDING SET, ARC, INERT GAS SHIELDED: PLASTIC OR METAL LINED GUN; FOR 3/64 IN. WIRE; DC, 115V (WESTINGHOUSE MODEL SA-135) FSN HEADQUARTERS, DEPARTMENT OF THE ARMY FEBRUARY 1969

2

3 *TM P T ECHNICAL M ANUAL HEADQUARTERS DEPARTMENT OF THE ARMY No P W ASHINGTON, D. C., 8 February 1969 DIRECT AND GENERAL SUPPORT AND DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST WELDING SET, ARC, INERT GAS SHIELDED: PLASTIC OR METAL LINED GUN; FOR 3/64 IN. WIRE; DC, 115V (WESTINGHOUSE MODEL SA-135) FSN Current as of 12 December 1968 S ECTION I. II. Group SECTION III. IV. Paragraph INTRODUCTION Scope General Explanation of columns Special information How to locate repair parts Abbreviations Federal supply codes for manufacturers Report of equipment publications improvements REPAIR PARTS FOR DS, GS, AND DEPOT MAINTENANCE Miscellaneous Body, Chassis or Hull, and Accessory Items 2210 Data plates and instruction holders Welding, metalizing, metal heating and plating equipment Gas welding, flame cutting Control panels, housing, cubicles Connecting devices Protective services, electrical Switching, timing and speed control Resistors Rectifiers Head, torch and gun unitized components General Use Standardized Parts 9501 Bulk material SPECIAL TOOLS, TEST AND SUPPORT EQUIPMENT FOR DS, GS, AND DEPOT MAINTENANCE-NOT APPLICABLE FEDERAL STOCK NUMBER AND REFERENCE NUMBER INDEX Page iii iii iii iv v v v v Page 1 *This manual together with TM P, 8 February 1969 supersedes TM P, 27 August i

4

5 SECTION I INTRODUCTION 1. Scope This manual lists repair parts required for the performance of direct support, general support, and depot maintenance of the welder. 2. General a. The repair parts list is arranged as follows: (1) Individual parts and major assemblies are listed alphabetically by item name within the numbered functional groups. (2) Assembly components and subassemblies are indented and listed alphabetically by item name under major assemblies. b. This Repair Parts and Special Tools List is divided into the following sections: (1) Repair Parts-Section II. A list of repair parts authorized for the performance of maintenance at the direct support, general support, and depot level. (2) Special Tools, Test and Support Equipment-Section III. A list of special tools, test and support equipment authorized for the performance of maintenance at the direct support, general support, and depot level. (Not applicable) (3) Federal Stock Number and Reference Number Index-Section IV. A list of Federal stock numbers followed by reference numbers in ascending alpha-numeric sequence cross-referenced to index number. 3. Explanation of columns The following provides an explanation of columns in the tabular lists in Sections II and III: a. Source Maintenance, and Recoverability Codes (SMR), Column (1). (1) Source Code, indicates the selection status and source for the listed item. Source codes used are: Code P M Explanation Applied to repair parts which are stocked in or supplied from DSA/GSA or Army Supply system, and authorized for use at indicated maintenance categories. Applied to repair parts which are not procured or stocked but are to be manufactured at indicated maintenance categories. Code A X X1 X2 C G Explanation Applied to assemblies which are not procured or stocked as such but made up of two or more units, each of which carry individual stock numbers and descriptions and are procured and stocked and can be assembled by units at indicated maintenance categories. Applied to parts and assemblies which are not procured or stocked, the mortality of which is normally below that of the applicable end item, and the failure of which should result in retirement of the end item from the supply system. Applied to repair parts which are not procured or stocked, the requirement for which will be supplied by use of the next higher assembly or components. Applied to repair parts which are not stocked. The indicated maintenance category requiring such repair parts will attempt to obtain them through cannibalization; if not obtainable through cannibalization, such repair parts will be requisitioned with supporting justification through normal supply channels. Applied to repair parts authorized for local procurements. If not obtainable from local procurement, such repair parts will be requisitioned through normal supply channels with a supporting statement of nonavailability from local procurement. Applied to major assemblies that are procured with PEMA, Procurement Equipment Missile Army) funds for initial issue only to be used as exchange assemblies at DSU and GSU maintenance level. These assemblies will not be stocked above DSU and GSU level or returned to depot supply level. Note. Source code is not shown on common hardware items known to be readily available in Army supply channels and through local procurement. (2) Maintenance Code, indicates the lowest category of maintenance authorized to install the listed item. The maintenance level codes are: Code O F H D Explanation Organizational maintenance Direct support maintenance General support maintenance Depot maintenance iii

6 (3) Recoverability Code, indicates whether unserviceable items should be returned for recovery or salvage. Items not coded are expendable. Recoverability codes are: Code R T U Explanation Applied to repair parts and assemblies which are economically repairable at DSU and GSU activities and normally are furnished by supply on an exchange basis. Applied to high dollar value recoverable repair parts which are subject to special handling and are issued on an exchange basis. Such repair parts normally are repaired or overhauled at depot maintenance activities. Applied to repair parts specifically selected for salvage by reclamation units because of precious metal content, critical materials, high dollar value reusable casings or castings. (4) This column also lists, below the SMR code, an index number for each item in ascending numerical sequence, which is used to locate items in the publication when the Federal stock number and/or reference number is known. b. Federal Stock Number, Column (2). This column indicates the Federal stock number for the item. C. Description, Column (3). This column indicates the Federal item name and any additional description of the item required. A part number or other reference number is followed by the applicable five-digit Federal supply code for manufacturers in parentheses. Material required for manufacture or fabrication is identified. d. Unit of Issue, Column (4). This column indicates the unit used as basis for issue, e.g., ea, pr, ft, yd, etc. e. Quantity Incorporated in Unit Pack, Column (5). This column indicates the actual quantity contained in the unit pack. f. Quantity Incorporated in Unit, Column (6). This column indicates the quantity of the item used in the functional group. g. Thirty-Day DS/GS Maintenance Allowances, Columns (7) and (8). (1) The allowance columns are divided into three subcolumns. Indicated in each subcolumn is the quantity of items authorized for the number of equipments supported. Items authorized for use as required but not for initial stockage are identified with an asterisk in the allowance column. (2) The quantitative allowances for DS/GS levels of maintenance will represent initial stockage for a 30-day period for the number of equipments supported. (3) Determination of the total quantity of parts required for maintenance of more than 100 of these equipments can be accomplished by converting the equipment quantity to a decimal factor by placing a decimal point before the next to last digit of the number to indicate hundreths, and multiplying the decimal factor by the parts quantity authorized in the allowance column. Example, authorized allowance for equipments is 40; for 150 equipments multiply 40 by 1.50 or 60 parts required. h. One-Year Allowances Per 100 Equipments/ Contingency Planning Purposes, Column (9). This column indicates the quantity required for distribution and contingency planning purposes. The range of items indicates total quantities of all authorized items required to provide for adequate support of 100 equipments for one year. i. Depot Maintenance Allowance Per 100 Equipments, Column (10). This column indicates the quantity authorized for depot maintenance of 100 equipments. Items authorized for use but not for initial stockage are identified with an asterisk in the allowance column. j. Illustration, Column (11). (1) Figure number. Indicates the figure number of the illustration in which the item is shown. (2) Item number. Indicates the callout number used to reference the item in the illustration. 4. Special Information a. Repair parts mortality has been based on 1,000 hours of operation per year. b. Parts which require manufacture or assembly at a category higher than that authorized for installation will indicate in the source column the higher category. c. The following publications pertain to the welder and its components: TM Operator, organizational, field and depot maintenance manual. TM P Organizational maintenance repair parts and special tool lists. iv

7 5. How to Locate Repair Parts a. When Federal stock number or reference number is unknown: (1) First. Using the table of contents, determine the functional group within which the repair part belongs. (2) Second. Find the illustration covering the functional group to which the repair part belongs. (3) Third. Identify the repair part on the illustration, and note the illustration figure and item number of the repair part. (4) Fourth. Using the Repair Parts Listing, find the functional group to which the repair part belongs and locate the illustration figure and item number noted on the illustration. b. When Federal stock number or reference number is known: (1) First. Using the Index of Federal Stock Numbers and Reference Numbers, find the pertinent Federal stock number or reference number. This index is in ascending alphanumeric sequence cross-referenced to an index number. (2) Second. Using the Repair Part Listing, find the index number referenced in the Index of Federal Stock Numbers and Reference Numbers. 6. Abbreviations ac alternating current amp ampere (s) AWG American Wire Gage dc direct current deg degree dia diameter (s) ea each ft feet (foot) grp group id inside diameter in inch (es) lg long mtg mounting No numher od outside diameter (s) sh sheet thd thread (ed) (s) thk thick (ness) uf microfarad (s) u/w used with v volt (s) w width w/ with 7. Federal Supply Codes for Manufacturers Code Manufacture Cornell-Dubilier Electric Corp Heyman Mfg. Co Sprague Electric Co Victor Equipment Co Cambridge Thermionic Corp Dzus Fastener Co. Inc Littlefuse Inc American Machine and Foundry Co Westinghouse Electric Corp. Control Division 8. Report of Equipment Publications Improvements Report of errors, omissions, and recommendations for improving this publication by the individual user is encouraged. Reports should be submitted on DA Form 2028 (Recommended Changes to DA Publications) and forwarded direct to Commanding General, U. S. Army Mobility Equipment Command, ATTN: AMSME- MPP, 4300 Goodfellow Boulevard, St. Louis, Mo v

8

9 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. SECTION II. REPAIR PARTS FOR DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE GROUP - 22 MISCELLANEOUS BODY, CHASSIS OR HULL, AND ACCESSORY ITEMS DATA PLATES AND INSTRUCTION HOLDERS X2 F PLATE, IDENTIFICATION: CORPS OF ENGINEER TYPE A EA X2 O PLATE, NAME: CONTROL EA P3340A (88725) F SCREW, TAPPING, THREAD FORMING: IDENTIFICATION PLATE EA 4 * * * * * * * * MOUNTING O SCREW, TAPPING, THREAD FORMING: NAME PLATE MOUNTING, EA 4 * * * * * * * * CADIMIUM OR ZINC PLATED; NO THD SIZE; 1/4 IN. LG GROUP 44 - WELDING, METALIZING, METAL HEATING AND PLATING EQUIPMENT GAS WELDING, FLAME CUTTING P O REGULATOR: ARGON GAS, TWO STAGES EA 1 * * 2 * * IN5945 (88725) X BALL, BEARING: CHECK, IN. DIA EA (63026) X1 BODY EA (63026) X1 BODY EA (63026) X BUTTON: SPRING EA SVJ90-02 (63026) X1 BUTTON: SPRING EA SVJ90-02 (63026) 1

10 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X1 CONNECTION: INLET EA (63026) X1 CONNECTION: OUTLET EA (63026) X1 CONNECTION: OUTLET EA (63026) X1 CUP: THORPE TUBE EA (63026) X WASHER, SPLIT: FRICTION HIGH PRESSURE AND LOW PRESSURE EA (63026) X1 DIAPHRAGM ASSEMBLY: HIGH PRESSURE EA (63026) X1 CENTRALIZER EA (63026) X DIAPHRAGM EA (63026) X1 PLATE: DIAPHRAGM EA (63026) X1 DIAPHRAGM ASSEMBLY: LOW PRESURE EA (63026) X1 CENTRALIZER EA (63026) X DIAPHRAGM EA (63026) X1 NUT EA (63026) X1 PLATE: DIAPHRAGM EA (63026) X1 WASHER EA (63026) 2

11 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X FILTER EA (63026) X PRESSURE, DIAL: GAGE, BRASS CASE, 2 IN., 0 TO 4000 EA POUNDS 4000LB (63026) X1 GASKET: THORPE TUBE, LOWER EA (63026) X1 GASKET: THORPE TUBE, UPPER EA (63026) X1 GUIDE: SPRING EA (63026) X1 HOUSING: CAP, HIGH PRESSURE EA (63026) X1 HOUSING: CAP, LOW PRESSURE EA (63026) X NOZZLE: HIGH PRESSURE AND LOW PRESSURE EA VTS85-06 (63026) X1 NUT: BODY EA (63026) X1 NUT, CAP EA (63026) X1 NUT: CAP, DIAPHRAGM PLATE EA (63026) X1 NUT: INLET EA A (63026) X NUT, PLAIN, CAP EA VTS85-09 (63026) X PACKING, PREFORMED EA (63026) X PACKING, PREFORMED: THORPE TUBE EA (63026) 3

12 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X RETAINER PACKING: HIGH PRESSURE AND LOW PRESSURE EA (63026) X1 RING: SLIP, DIAPHRAGM EA (63026) X1 SCREW: ADJUSTING EA VTS95-06 (63026) X1 SCREW: ADJUSTING, HIGH PRESSURE EA VTS40-13 (63026) X1 SEAT ASSEMBLY: HIGH PRESSURE EA (63026) X1 HOLDER: SEAT EA (63026) X1 SEAT UNIT EA V (63026) X NUT: SEAT EA V50-36 (63026) X1 SEAT EA SR47-02 (63026) X STEM, NEEDLE VALVE EA (63026) X1 SEAT ASSEMBLY: HIGH PRESSURE EA (63026) X1 HOLDER: SEAT EA (63026) X1 SEAT UNIT EA V (63026) X NUT: SEAT EA V50-36 (63026) X WASHER, NONMETALLIC EA VTS40-02D (63026) 4

13 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X1 STEM EA VTS85-02A (63026) X SPACER, RING: SLIP, DIAPHRAGM, LOW PRESSURE EA (63026) X1 SPRING: ADJUSTING EA SVJ90-03 (63026) X1 SPRING: ADJUSTING, HIGH PRESSURE EA SVJ90-03 (63026) X SPRING, HELICAL, COMPRESSION: VALVE PRESSURE AND LOW EA PRESSURE (63026) X1 SWIVEL: INLET EA (63026) X TUBE: THROPE EA (63026) X VALVE: SAFETY EA (63026) X1 VALVE ASSEMBLY, CONTROL EA (63026) X WASHER, LOCK: VALVE STEM EA VTS50-07B (63026) CONTROL PANELS, HOUSING, CUBICLES X2 0 CONTROL ASSEMBLU: AC/DC EA G9359 (88725) X2 0 BASE: CABINET EA D037H02 (88725) X BUSHING, RUBBER: CAPACITOR CLAMP TO CABINET MOUNTING, EA 1 SEE GRP CADMIUM TO ZINC CHROMATE, NO THD SIZE, 1/4 IN. LG X BUSHING, STRAIN RELIEF: STRAIN, CURRENT EA 1 SEE GRP SR8P1 (28520) 5

14 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. P CABLE ASSEMBLY: CURRENT EA 1 SEE GRP C1598G13 (88725) P CABLE ASSEMBLY: GROUND EA 1 SEE GRP C524G10 (88725) P CABLE ASSEMBLY: LINE EA 1 SEE GRP C512G04 (88725) P CAPACITOR: ARMATURE RELAY EA 2 SEE GRP P47306 (56289) X2 0 CAPACITOR, FIXED, ELECTROLYTIC: WELDING GUN, RECEPTACLE EA TO LOAD RELAY BR30015 (14655) X2 0 CLAMP: CAPACITOR TO CABINET MOUNTING EA 1 SEE GRP (88725) X2 0 CLAMP, LOOP EA A027H01 (88725) X2 0 CLAMP, LOOP: CABLE TO BASE, RUBBER COVERED LOOP, EA /16 IN. ID, OF LOOP, 1/16 IN. THK MATERIAL, 5/8 IN. WIDE 11/16 IN. CENTER OF LOOP TO CENTER OF BOLT HOLE, U/W NO. 8 SCREW SIZE (88725) X2 0 CLIP, LOOP: NYLON FM10001, 3/8 IN. ID, IN. EA CENTER OF LOOP TO CENTER OF HOLE, IN. CENTER OF HOLE TO END, IN. THK, IN. W, IN. ID OF HOLE 52D9036H05 (88752) X2 0R CONTRACTOR EA 1 SEE GRP D9649COMBBB00 (88725) X2 0 ENCLOSURE EA D037G02 (88725) X2 0 CABINET ASSEMBLY EA D037G01 (88725) X2 0 GASKET EA D037H09 (88725) 6

15 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X2 0 GROMMET EA B188H05 (88725) X STUD, TURNLOCK FASTENER EA AJ5-40 (72794) X2 0 FISH PAPER: CONTRACTOR FRAME TO MOUNTING PANEL, 6-1/8 EA 1 SEE GRP IN. LG, 3 IN. WIDE, IN. THK 448A043H01 (88725) X2 0 FISH PAPER: CONTRACTOR MOUNTING PANEL TO CONTROL EA PANEL, 9-1/8 IN. LG, 3 IN. WIDE, IN. THK 448A043H02 (88725) X2 0 FITTING: GAS IN EA 1 SEE GRP A05AH01 (88725) X2 0 FITTING: GAS OUT EA 1 SEE GRP A049H01 (88725) P FUSE CARTRIDGE: LINE, 2 AMP EA 4 SEE GRP (75915) P FUSE CARTRIDGE: MOTOR, LAMP EA 2 SEE GRP (75915) P FUSE HOLDER: MOTOR AND LINE EA 3 SEE GRP C612H02 (88725) X2 0 KNOB EA 1 SEE GRP (88725) NUT, PLAIN, HEXAGON: CAPACITOR CLAMP TO CABINET EA 1 SEE GRP MOUNTING, CADMIUM PLATED, NO THD SIZE NUT, PLAIN, HEXAGON: CLAMP SCREW TO BASE MOUNTING EA 3 * * * * * * * * NUT, PLAIN, HEXAGON: CONTROL PANEL TO CABINET MOUNTING EA 2 * * * * * * * * NUT, PLAIN, HEXAGON: LOOP CLAMP TO CABINET MOUNTING, EA 2 * * * * * * * * CADMIUM OR ZINC CHROMATE. NO THD SIZE NUT, PLAIN, HEXAGON: RECTIFIER TO CONTROL PANEL MOUNTING, EA 1 SEE GRP CADMIUM OR ZINC PLATED, NO THD SIZE 7

16 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO NUT,PLAIN, HEXAGON: RELAY TO CABINET MOUNTING, EA 2 SEE GRP CADMIUM OF ZINC CHROMATE, NO THD SIZE NUT, PLAIN, HEXAGON: RESISTOR TO CONTROL PANEL EA 2 SEE GRP MOUNTING, CADMIUM OR ZINC PLATED, 1/4-20 THD SIZE NUT,PLAIN, HEXAGON: TERMINAL STRIP TO CABINET EA 4 SEE GRP MOUNTING, CADMIUM OR ZINC CHROMATE, NO THD SIZE X2 0 PANEL: CONTROL EA C249H01 (88725) X2 0 PANEL: CONTROL, CONTRACTOR EA 1 SEE GRP C251H01 (88725) M 0 PANEL, SIDE: CONTROL EA MANUFACTURE FROM: P STEEL SHEET, CARBON, HOT ROLLED (14-1/2 IN. X 12- SH SEE GRP /16 IN. REQUIRED) X2 0 PIPE: SOLENOID VALVE, INLET EA 1 SEE GRP A015H02 (88725) X2 0 PIPE: SOLENOID VALVE, OUTLET EA 1 SEE GRP A015H07 (88725) P RECEPTACLE, WELDING GUN POWER SUPPLY EA 1 SEE GRP A012H01 (88725) P RECTIFIER, SEMICONDUCTOR DEVICE EA 1 SEE GRP C516G60 (88725) P RELAY ARMATURE: W/100V, DC COIL, 2 CIRCUIT EA 1 SEE GRP PR11D (77342) P RELAY ASSEMBLY: LOAD EA 1 SEE GRP B224G01 (88725) P RELAY: W/110V, DC COIL, 4 CIRCUIT EA 1 SEE GRP A471H11 (88725) X RELIEF: STRAIN, GROUND EA 1 SEE GRP SR2M1 (28520) 8

17 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X2 0 RELIEF: STRAIN, GUN EA 1 SEE GRP A526G03 (88725) X2 0 RELIEF: STRAIN, LINE EA 1 SEE GRP SR6P1 (77342) P RESISTOR, ADJUSTABLE MOTOR VOLTAGE SUPPLY EA 1 SEE GRP A473H05 (88725) P RESISTOR: ARMATURE RELAY TO LOAD RELAY EA 1 SEE GRP A473H03 (88725) P RESISTOR: CONTROL PANEL EA 1 SEE GRP A473H04 (88725) P RESISTOR: FUSE TO HOLDER TO LOAD RELAY EA 1 SEE GRP D436H33 (88725) P RHEOSTAT, WELDING WIRE FEED CONTROL EA 1 SEE GRP A460H01 (88725) SCREW, MACHINE: CLAMP TO BASE MOUNTING CADMIUM OR EA 3 * * * * * * * * ZINC PLATED, NO THD SIZE, 3/8 IN. LG SCREW, MACHINE: CONTROL PANEL TO CABINET MOUNTING, EA 2 * * * * * * * * CADMIUM OR ZINC PLATED, NO THD SIZE, 3/8 IN. LG SCREW, MACHINE: LOOP CLAMP TO CABINET MOUNTING, EA 1 * * * * * * * * CORROSION RESISTING, NO THD SIZE, 5/8 IN. LG SCREW, MACHINE: RELAY TO CABINET MOUNTING, CADMIUM EA 2 SEE GRP OR ZINC PLATED, NO THD SIZE, 5/8 IN LG SCREW, MACHINE: RESISTOR TO CONTROL PANEL MTG, EA 2 SEE GRP CADMIUM RO ZINC PLATED, 1/4-20 THD SIZE, 3/8 IN. LG SCREW, MACHINE: SOLENOID VALVE TO CABINET MOUNTING, EA 2 SEE GRP CADMIUM OR ZINC PLATED, NO THD SIZE, 1 1/4 IN. LG SCREW, MACHINE: TERMINAL STRIP TO CABINET MOUNTING, EA 1 SEE GRP CADMIUM OR ZINC PLATED, NO THD SIZE, 1 IN. LG SCREW, MACHINE: TERMINAL STRIP TO CABINET MOUNTING, EA 1 SEE GRP CADMIUM OR ZINC PLATED, NO THD SIZE, 1-1/8 IN. LG 9

18 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO SCREW, MACHINE: TERMINAL STRIP TO CABINET MOUNTING, EA 2 SEE GRP CORROSION RESISTING, NO THD SIZE, 5/8 IN. LG SCREW, TAPPING, THREAD CUTTING: RELAY AND ARMATURE EA 4 SEE GRP RELAY TO PANEL MOUNTING, CADMIUM OR ZINC PLATED, NO THD SIZE, 3/4 IN. LG SCREW, TAPPING, THREAD FORMING: CONTROL PANEL TO SIDE EA 2 * * * * * * * * PANEL MOUNTING, CADMIUM OR ZINC PLATED, NO THD SIZE, 3/8 IN. LG SCREW, TAPPING, THREAD FORMING: PANEL MOUNTING, EA 12 * * * * * * * * CADMIUM OR ZINC PLATED, NO THD SIZE, 3/8 IN. LG SCREW, TAPPING, THREAD FORMING: RESISTOR TO CONTROL EA 2 SEE GRP PANEL MOUNTING, CADMIUM OR ZINC PLATED, NO THD SIZE, 3/8 IN. LG M 0 SPACER: SOLENOID VALVE TO CABINET MOUNTING EA 2 SEE GRP P SWITCH, CONTROL PANEL: LINE EA 1 SEE GRP A051H02 (88725) P TERMINAL STRIP EA 1 SEE GRP B1029H15 (88725) P VALVE, SOLENOID EA 1 SEE GRP A472H02 (88725) WASHER, FLAT: CLAMP SCREW TO BASE MOUNTING, CADMIUM EA 3 * * * * * * * * OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: CAPACITOR CLAMP TO CABINET MOUNTING, EA 1 SEE GRP CADIUM OR ZINC PLATED, IN. ID, IN. OD, IN. THK WASHER, LOCK: CLAMP SCREW TO BASE MOUNTING, CADIUM EA 4 * * * * * * * * OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: CONTROL PANEL TO SIDE PANEL MOUNTING, EA 4 * * * * * * * * CADMIUM OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK 10

19 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO WASHER, LOCK: RECTIFIER TO CONTROL PANEL MOUNTING, EA 1 SEE GRP CADMIUM OR ZINC PLATED, IN. ID, IN. OD, IN. THK WASHER, LOCK: RELAY TO CABINET MOUNTING, CADMIUM OR EA 2 SEE GRP ZINC CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: RESISTOR TO CONTROL PANEL MOUNTING, EA 2 SEE GRP CADMIUM OR ZINC PLATED, IN. ID, IN. OD, IN. THK WASHER, LOCK: SOLENOID VALVE TO CABINET MOUNTING, EA 2 SEE GRP CADMIUM OR ZINC PLATED, IN. ID, IN. OD, IN. THK WASHER, LOCK: TERMINAL STRIP TO CABINET MTG, CADMIUM EA 1 SEE GRP OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK M 0 WIRING HARNESS: CONTROL EA MANUFACTURE FROM: X TERMINAL, LUG: COPPER, TINNED FINISH, NO EA AWG, FOR NO. 5 OR 6 SCREW SIZE P WIRE, ELECTRICAL (4 FT. REQUIRED) FT SEE GRP P WIRE, ELECTRICAL (24 IN. REQUIRED) FT SEE GRP P WIRE, ELECTRICAL ( 4 FT. REQUIRED) FT SEE GRP P WIRE, ELECTRICAL (24 IN. REQUIRED) FT SEE GRP P WIRE, ELECTIRCAL (24 IN. REQUIRED) FT SEE GRP P WIRE, ELECTRICAL (4 FT. REQUIRED) FT SEE GRP P WIRE, ELECTRICAL (4 FT. REQUIRED) FT SEE GRP P WIRE, ELECTRICAL (4 FT. REQUIRED) FT SEE GRP CONNECTING DEVICES X BUSHING, STRAIN REFLEF: STRAIN, CURRENT EA SR8P1 (28520) 11

20 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. P CABLE ASSEMBLY: CURRENT EA 1 * * 2 * * B142G01 (88725) P CABLE ASSEMBLY: CURRENT EA 1 * * 2 * * C1598G13 (88725) P CABLE ASSEMBLY: GROUND EA 1 * * 2 * * C524G10 (88725) P F CABLE ASSEMLBLY: GUN TO TERMINAL STRIP EA 1 * * 2 * * B796G03 (88725) P CABLE ASSEMBLY: LINE EA 1 * * 2 * * C512G04 (88725) X2 0 FITTING: GAS IN EA A050H01 (88725) X2 0 FITTING: GAS OUT EA A049H01 (88725) P HOSE ASSEMBLY: GAS EA 1 * * 2 * * C506G01 (88725) LOCKNUT, PIPE: GAS INLET AND OUTLET PIPE TO CABINET MTG, EA 2 * * * * * * * * ZINC PLATED, 1/8-27 THD SIZE LOCKNUT, PIPE; GUN RELIEF STRAIN MTG, 1/2-14 THD SIZE EA 1 * * * * * * * * NUT, PLAIN, HEXAGON; TERMINAL STRIP TO CABINET MTG, EA 4 * * * * * * * * CADMIUM OR ZINC CHROMATE, NO THD SIZE X2 0 PIPE: SOLENOID VALVE, INLET EA A015H02 (88725) X2 0 PIPE: SOLENOID VALVE, OUTLET EA A015H07 (88725) P RECEPTACLE, WELDING GUN POWER SUPPLY EA 1 * * 2 * * A012H401 (88725) LOCKNUT, PIPE; RECEPTACLE MTG, 1/2-14 THD SIZE EA 1 * * * * * * * * X RELIEF: STRAIN, GROUND EA SR2M1 (28520) 12

21 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X2 0 RELIEF: STRAIN, GUN EA A526G03 (88725) X1 LOCKNUT: STRAIN RELIEF, 3/8 IN. CONDUIT EA A526H02 (88725) X1 SEALING GRIP: STRAIN RELIEF EA A526H04 (88725) X2 0 RELIEF: STRAIN, LINE EA SR6P1 (77342) SCREW, MACHINE: TERMINAL STRIP TO CABINET MTG, CADMIUM EA 1 * * * * * * * * OR ZINC PLATED, NO THD SIZE, 1 IN. LG SCREW, MACHINE: TERMINAL STRIP TO CABINET MTG, CADMIUM EA 1 * * * * * * * * OR ZINC PLATED, NO. 8/32 THD SIZE 1 1/8 IN. LG SCREW, MACHINE: TERMINAL STRIP TO CABINET MTG, CORROSION EA 2 * * * * * * * * RESISTING, NO THD SIZE, 5/8 IN. LG P TERMINAL STRIP EA 1 * * 2 * * B1029H15 (88725) WASHER, LOCK: TERMINAL STRIP MTG, CADMIUM OR ZINC EA 1 * * * * * * * * CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: TERMINAL STRIP TO CABINET MTG, CADMIUM EA 1 * * * * * * * * OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK PROTECTIVE DEVICES, ELECTRICAL P FUSE, CARTRIDGE: LINE, 2 AMP EA (75915) P FUSE, CARTRIDGE: MOTOR LAMP EA (75915) P FUSE HOLDER: MOTOR AND LINE EA 3 * * 2 * * C612H02 (88725) 13

22 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO SWITCHING, TIMING AND SPEED CONTROL P CAPACITOR: ARMATURE RELAY EA (88725) X2 0 CAPACITOR, FIXED, ELECTROLYTIC: WELDING GUN RECEPTACLE EA TO LOAD RELAY BR30015 (14655) P F CAPACITOR: GUN EA 1 * * 2 * * P47302S2 (56289) P CAPACITOR: INSULATED TERMINAL TO ARMATURE RELAY, 1 UF, EA V+20 %, DC PJ4P1 (14655) X2 0 CLAMP: CAPACITOR TO CABINET MTG EA (88725) X2 OR CONTACTOR EA D9649COMBBBOO (88725) X1 BASE EA (88725) X1 BOX ASSEMBLY: ARC EA (88725) P F COIL: BLACK NO. 2, COMB B EA 1 * * 2 * * (88725) X1 COIL: BLOW OUT ARC HORM ASSEMBLY EA (88725) X1 CONNECTOR EA (88725) P F CONTACT, MOVING EA 1 * * 2 * * (88725) P F CONTACT, STATIONARY EA 1 * * 2 * * (88725) X1 CORE EA (88725) 14

23 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X1 FRAME ASSEMBLY EA (88725) X1 HOLDER: CONTACT SPRING EA (88725) X INSULATION: TUBE EA (88725) X1 LATCH EA (88725) X1 PIN: DOWEL EA D181H45 (88725) X1 PLATE: ARMATURE EA (88725) X1 PLATE: NAME, CONTACTOR EA (88725) X1 PLATE: NON-MAGNETIC EA (88725) X POLE FACE EA (88725) X POLE PIECE EA (88725) X POLE PIECE EA (88725) X1 RETAINING WASHER EA (88725) X SCREW, DRIVE: NAME PLATE, CADIMUM OR ZINC PLATED, EA NO. 2, 1/8 IN. LG X SCREW, MACHINE: ARMATURE PLATE MTG, CADMIUM OR ZINC EA PLATED, 1/4-20 THD SIZE, 1/2 IN. LG X SCREW, MACHINE: CADMIUM OR ZINC, PLATED, 1/4-20 THD EA SIZE, 5/8 IN. LG 15

24 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. X SCREW, MACHINE: COIL MTG, CADMIUM OR ZINC PLATED, EA /4-28 THD SIZE, 1/2 IN. LG X SCREW, MACHINE: CONTACT MTG, CADMIUM OR ZINCE PLATED, EA /4-28 THD SIZE, 3/8 IN. LG X SCREW, MACHINE: CONTACTOR TO MTG PLATE, CADMIUM OR EA ZINC PLATED, NO THD SIZE, 3/4 IN. LG X SCREW, MACHINE: LEAD ATTACHING, BRASS, NO EA THD SIZE, 1/4 IN. LG X1 SHUNT EA B9647G02 (88725) P F SPRING, CONTACT EA 1 * * 2 * * (88725) P F SPRING, KICK-OUT EA (88725) X STOP: ARMATURE EA (88725) X1 STUD EA D181H55 (88725) X1 SUPPORT: KICK-OUT SPRING EA (88725) X1 TERMINAL: FRONT CONNECTION EA B (88725) X WASHER, FLAT: COIL MTG, CADMIUM PLATED, 1/4 IN. ID, EA /8 IN. OD, IN. THK X WASHER, FLAT: CONTACT MOUNTING, CADMIUM OR ZINC CHROMATE, EA IN. ID, IN. OD, IN. THK X WASHER, FLAT: CONTACTOR SCREW MOUNTING, CADIMUM PLATED, EA IN. ID, 7/8 IN. OD, 1/16 IN. THK X1 WASHER: INSULATION EA (88725) 16

25 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (A) (B) 100 PER (C) (C) NO. PACK UNIT EQUIP 100 FIG ITEM CNTGCY EQUIP NO. NO. REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE X WASHER, LOCK: CADIMUM OR ZINC CHROMATE, IN. ID, EA IN. OD, IN. THK X WASHER, LOCK: CONTACT MOUNTING, CADIMUM OR ZINC CHROMATE, EA IN. ID, IN. OD, IN. THK X WASHER, LOCK: CONTACTOR SCREW MOUNTING, CADMIUM OR EA ZINC PLATED, IN. ID, IN. OD, IN.THK X WASHER, LOCK: LEAD SCREW ATTACHING CADIMUM OR ZINC EA CHROMATE, IN. ID, IN. OD, IN. THK X1 WASHER: MICA EA A560H05 (88725) X2 0 FISH PAPER: CONTACTOR FRAME TO MOUNTING PANEL, 6-1/18 IN. EA LG, 3 IN. W, IN. THK 448A043H01 (88725) M 0 LEAD, ELECTRICAL: RELAY GROUND EA MANUFACTURE FROM: X TERMINAL, LUG: NO. 16 TO NO. 22 AWG, 25/32 IN. LG, EA /16 IN. W, 1/4 IN. THK P WIRE, ELECTRICAL (6 IN. REQUIRED) FT SEE GRP NUT, PLAIN, HEXAGON: CAPACITOR CLAMP TO CABINET MOUNTING, EA 1 * * * * * * * * CADMIUM PLATED, NO THD SIZE NUT, PLAIN, HEXAGON: RELAY TO CABINET MOUNTING, CADMIUM EA 2 * * * * * * * * OR ZINC CHROMATE, NO THD SIZE 0 NUT: WELL, CONTACTOR MOUNTING, RUBBER W/BRASS THREADED EA 2 * * * * * * * * INSET 3/8-16 THD SIZE, SHOULDERED, 3/4 IN. OD, OF SMALL SHOULDER, 11/16 IN. HIGH, 1 3/4 IN. OD, OF LARGE SHOULDER, 3/8 IN. HIGH, 1-1/16 IN. OVERALL 419A065H01 (88725) X2 0 PANEL: CONTROL, CONTACTOR EA C251H01 P RELAY, ARMATURE: W/110V, DC COIL, 2 CIRCUIT EA 1 * * 2 * * PR11D (77342) 17

26 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. P RELAY ASSEMBLY: LOAD EA 1 * * 2* * B224G01 (88725) P RELAY: W/110V, DC COIL, 4 CIRCUIT EA 1 * * 2 * * AX71H11 (88725) X1 COIL EA B222H01 (88725) X1 COIL ASSEMBLY: RELAY EA B222G01 (88725) X1 RELAY: SPST, ONE OPEN CONTACT EA PR2949 (77342) X1 TERMINAL EA B222H02 (88725) SCREW, CAP, HEXAGON HEAD: CONTACTOR MOUNTING, CADIMUM OR EA 2 * * * * * * * * ZINC PLATED, 3/8-16 THD SIZE, 1 1/4 IN. LG SCREW, MACHINE: CAPACITOR CLAMP TO CABINET MOUNTING, EA 1 * * * * * * * * CADMIUM OR ZINC CHROMATE, NO THD SIZE, 1/4 IN. LG X SCREW, MACHINE: INSULATED TERMINAL MOUNTING EA SCREW, MACHINE: RELAY TO CABINET MOUNTING, CADMIUM EA 2 * * * * * * * * OR ZINC CHROMATE, NO THD SIZE, 5/8 IN. LG SCREW, MACHINE: SOLENOID VALVE TO CABINET MTG, CADMIUM EA 2 * * * * * * * * OR ZINC PLATED, NO THD SIZE, 1-1/4 IN. LG X SCREW, TAPPING, THREAD CUTTING: RELAY AND ARMATURE RELAY EA TO PANEL MTG, CADMIUM OR ZINC PLATED, NO THD SIZE, 3/4 IN. LG M 0 SPACER: SOLENOID VALVE TO CABINET EA MANUFACTURE FROM: P PIPE, STEEL (13/16 IN. REQUIRED FOR EACH SPACER) FT SEE GRP P SWITCH, CONTROL PANEL: LINE EA 1 * * 2 * * A051H02 (88725) 18

27 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (A) (B) 100 PER (C) (C) NO. PACK UNIT EQUIP 100 FIG ITEM CNTGCY EQUIP NO. NO. REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE P F SWITCH, INCHING EA 1 * * 2 * * B663H09 (88725) P F SWITCH, TRIGGER EA 1 * * 2 * * A3880H17 (88725) X2 0 TERMINAL: INSULATED EA F6 (71279) P VALVE, SOLENOID EA 1 * * 2 * * A472H02 (88725) WASHER, FLAT: INSULATED TERMINAL MOUNTING, CADMIUM EA 1 * * * * * * * * OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: CAPACITOR CLAMP TO CABINET MTG, CADMIUM EA 1 * * * * * * * * OR ZINC PLATED, IN. ID, IN. OD, IN. THK WASHER, LOCK: CONTACTOR SCREW MTG, IN. ID, EA 2 * * * * * * * * IN. OD, IN. THK WASHER, LOCK: INSULATED TERMINAL MTG EA 1 * * * * * * * * WASHER, LOCK: RELAY TO CABINET MTG, CADMIUM OR ZINC EA 2 * * * * * * * * CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: SOLENOID VALVE TO CABINET MTG, CADMIUM EA 2 * * * * * * * * OR ZINC PLATED, IN. ID, IN. OD, IN. THK RESISTORS X2 0 KNOB EA (88725) NUT, PLAIN, HEXAGON: RESISTOR TO CONTROL PANEL MTG, EA 1 * * * * * * * * CADMIUM OR ZINC CHROMATE, NO THD SIZE NUT, PLAIN, HEXAGON: RESISTOR TO CONTROL PANEL MTG, EA 2 * * * * * * * * CADMIUM OR ZINC PLATED, 1/4-20 THD SIZE P RESISTOR, ADJUSTABLE MOTOR VOLTAGE SUPPLY: CONTROL PANEL EA 1 * 2 2 * A60H5 (88725) P RESISTOR: ARMATURE RELAY TO LOAD RELAY EA 1 * 2 2 * A4730H03 (88725) 19

28 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO. P RESISTOR: CONTROL PANEL EA 1 * 2 2 * A473H04 (88725) P RESISTOR: FUSE HOLDER TO LOAD RELAY EA 1 * 2 2 * D436H33 (88725) P RHEOSTAT, WELDING WIRE FEED CONTROL EA 1 * 2 2 * A460H01 (88725) SCREW, MACHINE: RESISTOR TO CONTROL PANEL MTG, CADMIUM EA 1 * * * * * * * * OR ZINC PLATED, NO THD SIZE, 2 1/2 IN. LG SCREW, MACHINE: RESISTOR TO CONTROL PANEL MTG, CADMIUM EA 2 * * * * * * * * OR ZINC PLATED, 1/4-20 THD SIZE, 3/8 IN. LG SCREW, TAPPING, THREAD FORMING: RESISTOR TO CONTROL EA 2 * * * * * * * * PANEL MTG, CADMIUM OR ZINC PLATED, NO THD SIZE, 3/8 IN. LG WASHER, FLAT: RESISTOR TO CONTROL PANEL MTG, 3/16 IN. EA 1 * * * * * * * * ID, 7/16 IN. OD, IN. THK WASHER, LOCK: RESISTOR TO CONTROL PANEL MTG, CADMIUM EA 1 * * * * * * * * OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: RESISTOR TO PANEL MTG, CADMIUM OR ZINC EA 2 * * * * * * * * PLATED, IN. ID, IN. OD, IN. THK X WASHER, NONMETALLIC: RESISTOR TO CONTROL PANEL MTG, EA FIBER, 13/64 IN. ID, 5/16 IN. OD, 1/16 IN. THK RECTIFIERS NUT, PLAIN, HEXAGON: RECTIFIER TO CONTROL PANEL MTG, EA 1 * * * * * * * * CADIMUM OR ZINC PLATED, NO THD SIZE P RECTIFIER, SEMICONDUCTOR DEVICE EA C516H60 (88725) WASHER, LOCK: RECTIFER TO CONTROL PANEL MTG, CADMIUM EA 1 * * * * * * * * OR ZINC PLATED, IN. ID, IN. OD, IN. THK 20

29 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO HEAD, TORCH AND GUN UNITIZED COMPONENTS X GUN ASSEMBLY: WELDING EA N5941 (88725) P ADAPTER EA 1 * * 2 * * A003H01 (88725) X2 0 ADAPTER, STRAIGHT, PIPE TO HOSE: BRASS, SPECIAL EA A043H01 (88725) X2 0 BARREL ASSEMBLY: GUN EA A002G01 (88725) X1 BARREL: GUN EA A001H02 (88725) X1 LUG: CURRENT EA A001H01 (88725) X2 0 BOLT, MACHINE: BEARING ARM EA A025H01 (88725) X2 0 BOLT, MACHINE: REEL COVER EA A029H01 (88725) P BOOT EA 1 * 2 * * A046H01 (88725) X2 0 BRACKET AND FITTING ASSEMBLY, MOUNTING EA C605G03 (88725) X2 0 BRACKET ASSEMBLY EA C554G02 (88725) X1 BRACKET, MOUNTING EA C554H04 (88725) X1 INSERT EA C554H03 (88725) X2 0 FITTING ASSEMBLY: GAS EA C605G04 (88725) 21

30 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO ELBOW, PIPE: BRASS; ONE END MALE, OTHER END FEMALE, EA 1 * * * * * * * * /8-27 THD SIZE ELBOW, PIPE: 45 DEG, ONE END MALE, OTHER END FEMALE, EA 1 * * * * * * * * /8-27 THD SIZE P BRACKET, REEL BRAKE SUPPORT EA 1 * * 2 * * A008H01 (88725) P BRAKE: REEL EA 1 * * 2 * * A011H01 (88725) P BUSHING, GUIDE: REAR EA A007H02 (88725) P BUSHING, SLEEVE: FRONT EA A338H03 (88725) P CABLE ASSEMBLY: CURRENT EA 1 SEE GRP B142G01 (88725) P F CABLE ASSEMBLY: GUN TO TERMINAL STRIP EA 1 SEE GRP B796G03 (88725) P F CAPACITOR: GUN EA 1 SEE GRP P47302S2 (56289) P COVER, WIRE REEL PROTECTING EA 1 * * 2 * * B71G01 (88725) X COVER: REEL EA C247H01 (88725) P GROMMET, RUBBER: 1/2 IN. ID. 1 IN. OD, 3/32 IN. THK EA 1 * * 2 * * (88725) X2 F HANDLE ASSEMBLY: GUN EA B663G01 (88725) P HANDLE EA 1 * * 2 * * D467G03 (88725) F SCREW, MACHINE: HANDLE MTG, CADIMUM OR ZINC PLATED, EA 1 * * * * * * * * NO THD SIZE, 5/8 IN. LG 22

31 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO SCREW, MACHINE: SHIELD TO BRACKET MTG, CADMIUM OR EA 3 * * * * * * * * ZINC PLATED, NO THD SIZE, 3/8 IN. LG P F SPRING, HELICAL, COMPRESSION: TRIGGER EA 1 * * 2 * * D4432H01 (88725) P F SPRING, TRIGGER EA 1 * * 2 * * A091H01 (88725) P F SWITCH, INCHING EA 1 SEE GRP B663H09 (88725) P F SWITCH, TRIGGER EA 1 SEE GRP A3880H17 (88725) P F TRIGGER EA 1 * * 2 * * A089H01 (88725) P HOSE ASSEMBLY: - GAS EA 1 SEE GRP C506G01 (88725) P INSULATION EA 1 * * 2 * * A010H01 (88725) P INSULATION, GUN BARREL EA 1 * * 2 * * A005H02 (88725) X2 F INSULATOR: MOTOR EA A550H01 (88725) P F MOTOR EA 1 * * 2 * * C550G02 (88725) P NOZZLE, GAS EA B703H02 (88725) NUT, PLAIN, HEXAGON: DRIVE ROLL ATTACHING 1/4-20 EA 1 * * * * * * * * THD SIZE P ROLL, DRIVE EA 1 * * 2 * * A009G01 (88725) SCREW, MACHINE: BEARING ARM MTG, CADMIUM OR ZINC EA 1 * * * * * * * * PLATED, NO THD SIZE 5/8 IN. LG 23

32 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (A) (B) 100 PER (C) (C) NO. PACK UNIT EQUIP 100 FIG ITEM CNTGCY EQUIP NO. NO. REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE SCREW, MACHINE: BRACKET AND FITTING ASSEMBLY MTG, EA 1 * * * * * * * * CADMIUM OR ZINC CHROMATE, NO THD SIZE 1 IN. LG SCREW, MACHINE: BRACKET AND FITTING ASSEMBLY MTG, EA 3 * * * * * * * * CADIMUM OF ZINC PLATED, NO THD SIZE, 1 1/2 IN. LG F SCREW, MACHINE: HANDLE MTG, CADMIUM OR ZINC PLATED, EA 3 * * * * * * * * NO THD SIZE, 3/8 IN. LG X2 0 SCREW, MACHINE: HOUSING TO GUN BARREL MTG, NO EA THD SIZE, 1/4 IN. LG 576D964H68 (88725) SCREW, MACHINE: REEL SHAFT MTG, CADMIUM OR ZINC PLATED, EA 1 * * * * * * * * /16-18 THD SIZE, 3/4 IN. LG SCREW, TAPPING, THREAD CUTTING: BRAKE TO BRAKE SUPPORT EA 2 * * * * * * * * MTG, CADMIUM OR ZINC PLATED, NO THD SIZE, 1/4 IN. LG SCREW, TAPPING, THREAD FORMING: BRAKE SUPPORT MTG, EA 2 * * * * * * * * CADMIUM OR ZINC PLATED, NO THD SIZE, 3/8 IN. LG P SCREW: THUMB EA 1 * * 2 * * A505G01 (88725) P SEAL, WIRE FEED REEL SHAFT EA 2 * * 2 * * D964H07 (88725) SETSCREW: FRONT AND REAR GUIDE BUSHING TO BRACKET EA 2 * * * * * * * * ATTACHING, NO THD SIZE, 1/8 IN. LG X2 0 SETSCREW: 1/4-20 THD SIZE, 1/4 IN. LG EA A3880H45 (88725) X2 0 SHAFT: REEL EA A024H01 (88725) X2 0 SHIELD: REEL COVER EA D963G02 (88725) X2 F SLEEVING: MOTOR LEAD EA A484H02 (88725) P SPRING, HELICAL, COMPRESSION EA 1 * * 2 * * A027H01 (88725) 24

33 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (A) (B) 100 PER (C) (C) NO. PACK UNIT EQUIP 100 FIG ITEM CNTGCY EQUIP NO. NO. REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE X2 0 STRAP: COPPER EA D964H64 (88725) P SWING ARM ASSEMBLY EA 1 * * 2 * * B141G01 (88725) X2 0 ARM: BEARING EA A026H02 (88725) P BEARING, IDLER-ROLL EA 1 * * 2 * * D415H39 (88725) P SCREW: NYLON EA 1 * * 2 * * A169H01 (88725) P WASHER, WIRE PRESSURE ARM EA 2 * * 2 * * B141H04 (88725) P TUBE, GUIDE EA B172H09 (88725) X2 0 TUBE: GUN EA A004H01 (88725) P WASHER EA 2 * * 2 * * A006H01 (88725) P WASHER EA 1 * * 2 * * A006H02 (88725) WASHER, FLAT: DRIVE ROLL ATTACHING, IN. ID, EA 1 * * * * * * * * IN. OD, IN. THK WASHER, FLAT: REEL SPACER, CADMIUM OR ZINC CHROMATE, EA 1 * * * * * * * * IN. ID, IN. OD, IN. THK WASHER, FLAT: SHIELD TO BRACKET, BRAKE SUPPORT MTG, EA 5 * * * * * * * * CADMIUM OR ZINC CHROMATE, IN. ID, IN. OD, IN. THK WASHER, LOCK: BRACKET AND FITTING ASSEMBLY MTG, CADMIUM EA 9 * * * * * * * * OR ZINC PLATED, IN. ID, IN. OD, IN. THK WASHER, LOCK: DRIVE ROLL ATTACHING IN. ID, EA 1 * * * * * * * * IN. OD, IN. THK 25

34 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) SMR QTY 30-DAY 30-DAY 1-YR DEPOT ILLUS- CODE FEDERAL DESCRIPTION INC QTY DS MAINT GS MAINT ALW MAINT TRATION STOCK IN INC ALLOWANCE ALLOWANCE PER ALW- (A) (B) INDEX NUMBER UNIT IN (A) (B) (C) (A) (B) (C) 100 PER NO. PACK UNIT EQUIP 100 FIG ITEM REFERENCE NO. & MFR. CODE USABLE ON CODE UNIT OF ISSUE CNTGCY EQUIP NO. NO GROUP 95 - GENERAL USE STANDARDIZED PARTS BULK MATERIAL P PIPE, STEEL: 1/2 IN DIA, IN. WALL THK FT * * * * * * P STEEL SHEET, CARBON, HOT ROLLED: IN. THK, SH * * * * * * IN. WIDE, 120 IN. LG P WIRE, ELECTRICAL: COPPER TINNED FINISH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 28 AWG, IN. DIA P WIRE,ELECTRICAL: COPPER, TINNED FINSIH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 28 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 28 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 29 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 29 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH, NO. 16 AWG FT * * * * * * STRANDS OF NO. 29 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 29 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH, NO. 16 AWG, FT * * * * * * STRANDS OF NO. 29 AWG, IN. DIA P WIRE, ELECTRICAL: COPPER, TINNED FINISH NO. 16 AWG, FT * * * * * * STRANDS OF NO. 29 AWG, IN. DIA 26

35 Figure 1. 27

36 28 Figure 2.

37 FIGURE 2 29

38 FIGURE 3 Figure 3. 30

39 Figure 4. 31

40 32 FIGURE 4

41 Figure 5. 33

42 3 4 FIGURE 5

43 Figure 6. Handle, Motor, and Related Parts. 35

44 36 Figure 7.

45 INDEX TO PARTS, FIGURE 7 REFERENCE FUNCTIONAL ITEM REFERENCE FUNCTIONAL ITEM NUMBER GROUP NAME NUMBER GROUP NAME ELBOW SWING ARM AY ELBOW SCREW FITTING AY SCREW ADAPTER WASHER GROMMET BARREL AY SHIELD INSULATION WASHER WASHER WASHER SCREW SCREW SCREW SCREW TUBE SCREW NOZZLE WASHER ADAPTER SHAFT TUBE SEAL SCREW COVER INSULATION BOLT SETSCREW SCREW BRACKET AY BRAKE BRACKET-FITTING AY BOLT BUSHING SPRING SETSCREW ARM SCREW WASHER BUSHING BEARING BRACKET 37

46 SECTION IV. INDEX-FEDERAL STOCK NUMBER AND REFERENCE NUMBER CROSS-REFERENCE TO INDEX NUMBER STOCK NUMBER INDEX NUMBER STOCK NUMBER INDEX NUMBER

47 SECTION IV. INDEX-FEDERAL STOCK NUMBER AND REFERENCE NUMBER CROSS-REFERENCE TO INDEX NUMBER (CONTINUED) STOCK NUMBER INDEX NUMBER STOCK NUMBER INDEX NUMBER

48 SECTION IV. INDEX-FEDERAL STOCK NUMBER AND REFERENCE NUMBER CROSS-REFERENCE TO INDEX NUMBER (CONTINUED) REFERENCE NO. MFG CODE INDEX NO. REFERENCE NO. MFG CODE INDEX NO. AJ P47302S BR P47302S BR PJ4P PR11D PR11D PR SR2M SR2M SR SR6P SR6P SR8P SR8P SVJ SVJ SVJ SVJ B5866G VTS40-02D VTS VTS50-07B VTS85-02A VTS VTS VTS V V V V B9647G P3340A F A007H A089H A091H A560H N N A338H A550H B663G B663H B663H B172H B188H D4432H D9649COMBBBOO

49 SECTION IV. INDEX-FEDERAL STOCK NUMBER AND REFERENCE NUMBER CROSS-REFERENCE TO INDEX NUMBER (CONTINUED) REFERENCE NO. MFG CODE INDEX NO. REFERENCE NO. MFG CODE INDEX NO. 31D9649COMBBBOO A473H B141G A484H B141H A505G B142G A526G B142G A526G B703H A526H B711G A526H B796G C605G B796G C605G C612H C612H A051H A051H B1029H C550G B1029H C554G B222G C554H B222H C554H B222H C506G B224G C506G B224G C524G LB C524G A001H C512G A001H C512G A002G A3880H A003H A3880H A004H A3880H A005H A169H A006H A024H A006H A027H A008H A043H A009G A043H A010H A043H A011H A012H C516H A012H C516H A015H D9036H A015H D181H A015H D181H A015H D415H A025H D436H A026H D436H A027H D467G A029H A043H D963G A046H D964H A049H D964H A049H C1598G A050H C1598G A050H C247H A065H C249H AX71H C251H A460H C251H A460H P A460H D964H A471H D037G A472H D037G A472H D037H A473H D037H A473H G A473H A473H A

50 By Order of the Secretary of the Army: Official: KENNETH G. WICKHAM, Major General, United States Army, The Adjutant General. W. C. WESTMORELAND, General, United States Army, Chief of Staff. Distribution: To be distributed in accordance with DA Form 12-25, Sec I (qty rqr Block #183), Direct and General Support maintenance requirements for Welding equipment.

51

52 TM P

53 This fine document... Was brought to you by me: Liberated Manuals -- free army and government manuals Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap watermarks and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends? I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on. I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines: <A HREF= Military and Government Manuals</A> Sincerely Igor Chudov Chicago Machinery Movers