Air and Vacuum Sewer Valves. Stainless Steel Trim Standard. Short Air & Vacuum Sewer Series
|
|
- Jessie Walters
- 6 years ago
- Views:
Transcription
1 ir and Vacuum Sewer Valves ir and Vacuum Sewer Valves Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Features Include Standard and short body series available vailable in sizes thru 10 ll RISPIN ir and Vacuum Valves have standard una-n seating material with a Shore durometer of This standard seat allows drip tight closure beyond - PSIG. Occasionally, a gravity system operates at pressures less than 10 PSIG. These applications require a soft seating material which will prevent leakage down to PSIG. This soft seating material should not be applied to systems with operating pressures greater than 0 PSIG, or high pressure leaks may occur around the seat. Stainless Steel Trim Standard ir and Vacuum Sewer Valves permit a large volume of air to be released from a pipeline when it is filling. It also allows air into a system when draining. RISPIN ir and Vacuum Sewer Valves feature a rigid stainless steel valve plug to seal off the outlet orifice. s a result, damage to the seating surface is much less likely to occur in surge conditions. drawing of a typical Sewer ir and Vacuum Valve seating area is shownbelow. The valve plug is protected from a rush of air by a stainless steel baffle. The baffle provides a rigid support for the float guide bushing while allowing the float rod enough clearance for self seating operation. The RISPIN ir and Vacuum Sewer Valve, like the light body Pressure Sewer Valve, is designed for a maximum cold water working pressure of 300 PSIG. ny combination of the Sewer ir and Vacuum Valve and Sewer Pressure ir Release Valve can be made with the appropriate piping arrangements to accommodate a specific application. Short ir & Vacuum Sewer Series MODEL INLET OUTLET HEIGHT S10S screwed 1 screwed 1 1/ S10S screwed 1 screwed 16 3/ S0S screwed screwed 1 1/ S0S screwed screwed 16 3/ Where height restrictions do not permit the use of the standard height valve, a short body Sewer ir and Vacuum or Pressure ir Release Valve can be supplied. Their function is identical to the standard Sewer Valves except that they operate in a shorter body. S SERIES rispin Valve, 600 Fowler ve., erwick, P IR-VLV T: (0) - F: (0) -6 sales@crispinvalve.com S
2 ir and Vacuum Sewer Valves ir and Vacuum Sewer Valves S SERIES D 0 1 ackflush Optional PRT ITEM MTERIL NO. 1 TOP ast Iron FLNGE ast Iron 3 ODY, SREW ast Iron 3F ODY, FLNGE ast Iron FLNGE GSKET rmstrong SET una-n Rubber 6 VLVE & FLOT ROD Stainless Steel ROD GUIDE STND Stainless Steel 8 FLOT ROD GUIDE Nylatron FLOT Stainless Steel 11 ROD GUIDE NUT Stainless Steel 1 STND ROD SREW Stainless Steel STND ROD SREW Stainless Steel 1 STND ROD GSKET Fibre 1 STND ROD NUT Steel 1 FLNGE OLT Steel FLNGE NUT Steel 33 FLUSH PLUG Steel Standard apacity/light ody Series Model Inlet Outlet Width Width Height Height NPT NPT w/ack w/ack w/ack Flush Flush Flush SL0 1-11/16 1-3/ 1-1/ -1/ 60 Note: Operating pressures below 0 PSIG require soft seating material. Dimensions and Weights Model Inlet Outlet Height Width NPT Height Width w/ack w/ack w/ack Flush Flush Flush S0 NPT 1/ 10 1/16 1/ -1/ 3 10 S1 1# Flg. 10 1/ / -1/ 6 S30 3 NPT 3 1 3/ 10 1/ -1/ S31 3 1# Flg / 10 /16-1/ S NPT 3 1/ 11 1/ S1 1# Flg. 3 1/ 11 1/ 3 1/ S61 6 1# Flg /8 1 1/ / S81 8 1# Flg. 8 /16 1 3/ 3-1/ 33 0 S # Flg / 1 1/ 3-1/ *ll rispin valves are hydrostatically tested at 10% of their maximum working pressure. ack flushing attachments are available with any sewer valve arrangement and include: isolation gate valve, - 1 flushing valves and of 1 hose with quick disconnect attachments. 10 S rispin Valve, 600 Fowler ve., erwick, P IR-VLV T: (0) - F: (0) -6 sales@crispinvalve.com
3 D Submittal Sheet for rispin S Series ir/vacuum Sewer Valve (standard) Manufactured in compliance with NSI/WW 1 Date: October, ITEM DESRIPTION MTERIL STM TOP ST IRON 16 L. FLNGE ST IRON 16 L. 3 ODY ST IRON 16 L. FLNGE GSKET RMSTRONG N-80 N/ SET UN-N RUER D000 6 VLVE & FLOT ROD STINLESS STEEL 8 ROD GUIDE STND STINLESS STEEL 8 FLOT ROD GUIDE NYLTRON D8 FLOT STINLESS STEEL 11 ROD GUIDE NUT STINLESS STEEL 1 1 STND ROD SREW STINLESS STEEL 13 STND ROD STINLESS STEEL 8 1 STND ROD GSKET FIER D10 1 OLT STEEL 30 NUT STEEL 63 * DRIN PLUG ST IRON 16 L. 0 INTERFERENE PIN STINLESS STEEL 8 OPTIONL K FLUSH OMPONENTS *1 HOSE SSEMLY D.PLT STEEL&RUER N/ * NIPPLE STEEL 3 *3 NIPPLE STEEL 3 * GTE VLVE RSS N/ * GTE VLVE RSS N/ Size MODEL INLET SIZE OUTLET SIZE D WHT. SL0 NPT 1 NPT. 1.0 SL0 NPT 1 NPT ir and Vacuum Release Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or is under negative pressure. The valve(s)hall be of the long body design, and shall operate by sealing the una-n Rubber seat with a stainless steel valve disc as the float rises when water enters the valve body. The valve(s) shall automatically open when the system drains, or is under negative pressure, so that air may enter the line. Valve construction shall be NPT screwed or NSI lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir and Vacuum Sewer Valves, as manufactured by rispin-multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG * Parts are interchangable and optional at customer s request. rispin Valve, 600 Fowler ve., erwick, P IR-VLV T: (0) - F: (0) -6 sales@crispinvalve.com SUMITTL SHEET FOR S SERIES 11 S
4 Submittal Sheet for rispin S Series ir/vacuum Sewer Valve (high) Manufactured in compliance with NSI/WW 1 Date: October, 001 SUMITTL SHEET FOR S SERIES 1 S ir & Vacuum Sewer Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or under negative pressure. Valve construction shall be NPT screwed or NSI lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir and Vacuum Sewer Valves, as manufactured by rispin-multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG Size MODEL INLET SIZE OUTLET SIZE D WT. S0 NPT NPT **S1 1# FLG NPT S0 NPT NPT **S1 1# FLG NPT S30 3 NPT 3 NPT S31 3 1# FLG 3 NPT S30 3 NPT 3 NPT S31 3 1# FLG 3 NPT S NPT NPT S1 1# FLG NPT S NPT NPT S1 1# FLG NPT * Parts are interchangable and optional at customer s request. **Includes NSI L.1 companion FLG and nipple D 3F ITEM DESRIPTION MTERIL STM TOP ST IRON 16 L. FLNGE ST IRON 16 L. 3 ODY ST IRON 16 L. FLNGE GSKET RMSTRONG N-80 N/ SET UN-N RUER D000 6 VLVE & FLOT ROD STINLESS STEEL 6/31 ROD GUIDE STND STINLESS STEEL 8 FLOT ROD GUIDE NYLTRON N/ FLOT STINLESS STEEL 11 ROD GUIDE NUT STINLESS STEEL 1 1 STND ROD SREW STINLESS STEEL 13 STND ROD STINLESS STEEL 31 1 STND ROD GSKET FIER D10 1 STND ROD NUT STEEL 63 1 FLNGE OLT STEEL 30 FLNGE NUT STEEL 63 1 OLT STEEL 30 * PLUG ST IRON 16 L. OPTIONL K FLUSH OMPONENTS *1 HOSE SSEMLY D.PLT STEEL & RUER N/ * 1 X L. NIPPLE STEEL 31 *3 1 X 3 NIPPLE STEEL 31 * 1 GTE VLVE RSS N/ * NUT STEEL 63 *6 OLT STEEL 30 * 3 GTE VLVE ST IRON N/ *8 GSKET RMSTRONG N-80 N/ 6 rispin Valve, 600 Fowler ve., erwick, P IR-VLV T: (0) - F: (0) -6 sales@crispinvalve.com 3 1
5 D Submittal Sheet for rispin S Series 6 10 ir/vacuum Sewer Valve (high) Manufactured in compliance with NSI/WW 1 Date: October, ITEM QTY. DESRIPTION MTERIL STM 1 TOP ST IRON 16 L. 1 FLNGE ST IRON 16 L. 3F 1 ODY ST IRON 16 L. 1 FLNGE GSKET RMSTRONG N-80 N/ 1 SET UN-N RUER D VLVE&FLOT ROD STINLESS STEEL 6/31 1 ROD GUIDE SUPPORT ST IRON 16 L. 8 1 FLOT ROD GUIDE NYLTRON N/ 1 FLOT STINLESS STEEL 11 1 ROD GUIDE NUT STINLESS STEEL 1 1 OLT STEEL FLNGE OLT STEEL 30 1 FLNGE NUT STEEL 63 0 OLT STINLESS STEEL 13 1 FLNGE LIGN. PIN HRDENED STEEL 63 EYE PIN STEEL 63 * PLUG ST IRON 16 L. OPTIONL K FLUSH OMPONENTS *1 1 HOSE SSEMLY D.PLT STEEL&RUER N/ * 1 1 X L. NIPPLE STEEL 31 *3 1 1 X 3 NIPPLE STEEL 31 * 8 STUD STEEL 30 * 16 NUT STEEL 63 *6 1 GTE VLVE ST IRON N/ *8 1 8 GTE VLVE ST IRON N/ * 1 GSKET RMSTRONG N-80 N/ 3F 8 6 ir and Vacuum Sewer Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or is under negative pressure. Valve construction shall be NPT screwed or NSi lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir and Vacuum Sewer Valves, as manufactured by Multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG * Parts are interchangable and optional at customer s request. Size MODEL INLET SIZE OUTLET SIZE D WT. S61 6 1# FLG 6 NPT S61 6 1# FLG 6 NPT S81 8 1# FLG 8 NPT S81 8 1# FLG 8 NPT S # FLG 10 NPT S # FLG 10 NPT rispin Valve, 600 Fowler ve., erwick, P IR-VLV T: (0) - F: (0) -6 sales@crispinvalve.com SUMITTL SHEET FOR S SERIES S
6 SUMITTL SHEET FOR S SERIES 1 Submittal Sheet for rispin S Series 1 ir/vacuum Sewer Valve (S) Manufactured in compliance with NSI/WW 1 Date: October, 001 ir and Vacuum Release Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or is under negative pressure. Valve construction shall be NPT screwed or NSi lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir & Vacuum Sewer Valves, as manufactured by rispin-multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: The valve(s) shall be a special short body short valve with overall height not to exceed 1 1/. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG * Parts are interchangable and optional at customer s request. ITEM DESRIPTION MTERIL STM 1 TOP ST IRON 16 L. FLNGE ST IRON 16 L. 3 ODY ST IRON 16 L. FLNGE GSKET RMSTRONG N-80 N/ SET UN-N RUER D000 6 VLVE & FLOT ROD STINLESS STEEL 8 ROD GUIDE STND STINLESS STEEL 8 FLOT ROD GUIDE NYLTRON D8 FLOT STINLESS STEEL 11 ROD GUIDE NUT STINLESS STEEL 1 1 STND ROD SREW STINLESS STEEL 13 STND ROD STINLESS STEEL 8 1 STND ROD GSKET FIER D10 1 STND ROD NUT STEEL 63 1 OLT STEEL 30 NUT STEEL 63 * FLUSH PLUG ST IRON 16 L. 0 INTERFERENE PIN STINLESS STEEL 8 OPTIONL K FLUSH OMPONENTS *1 HOSE SSEMLY D.PLT STEEL & RUER N/ * NIPPLE STEEL 3 *3 NIPPLE STEEL 3 * NIPPLE STEEL 3 * GTE VLVE RSS N/ *6 GTE VLVE RSS N/ Size MODEL INLET SIZE OUTLET SIZE D WHT. S10S NPT 1 NPT S10S NPT 1 NPT S0S NPT NPT S0S NPT NPT S rispin Valve, 600 Fowler ve., erwick, P IR-VLV T: (0) - F: (0) -6 sales@crispinvalve.com D
Stainless Steel Trim Standard. ir and Vacuum Sewer Valves permit a large volume of air to
ir and Vacuum Sewer Valves Valve Functio n Exhausts air as a pipeline fills, and allows air in as pipeline drains Features Include Standard and short body series available vailable in sizes thru 10 ll
More informationVacuum Relief Performance Curves
Vacuum Relief Valves Crispin Vacuum Relief Valves Valve Function llows air to enter system when vacuum occurs Prevents air exhaustion during pump start-up Features Cracks open to admit air at.25 PSIG differential
More informationUS SERIES. Universal Sewer Valves. Universal Sewer Valves. Valve Function. Features Include
Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Allows accumulating air to escape while line is in operation Features Include Standard and short body series available
More informationThe Universal Sewer Air Release Valve is designed to permit
Universal Sewer Valves Universal Sewer Valves Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Allows accumulating air to escape while line is in operation Features
More informationA ir can accumulate in a sewage collection system that is
The & U eries ewage Air Valves Helps Prevent ystem hutdown tandard and High Capacity eries Available eries Includes Air & Vacuum and Pressure Combination Units Crispin ince 1905 Crispin Multiplex Manufacturing
More informationThe SC Series Surge Check Valves Sizes 3 thru 24 Available Cast Iron Construction Limits the Effects of System Surge on Air Release Valves.
The Series Sizes 3 thru 24 Available Cast Iron Construction Limits the Effects of System Surge on Air Release Valves Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA
More informationCrispin. The UL Series Universal Air Release Valves. Compound Lever System NPT Screwed or ANSI Class Flanges Available.
The UL Series Universal Air Release s Compound Lever System NPT Screwed or ANSI Class Flanges Available Crispin Since 105 sales@crispinvalve.com Universal Air Release s Universal Air Release UL SERIES
More informationHelps Prevent System Shutdown Standard and High Capacity Series Available Series Includes Air & Vacuum and Pressure Combination Units.
The & U eries ewage Air Valves Helps Prevent ystem hutdown tandard and High Capacity eries Available eries Includes Air & Vacuum and Pressure Combination Units Crispin ince 1905 Crispin Multiplex Manufacturing
More informationSeries 36-WW COMBINATION AIR VALVES DATA AND SIZING WASTEWATER SERVICE. (Single Body Style) Installation. Specifications. Purchase Specification
Series -WW COMINTION IR S DT ND SIZING WSTEWTER SERVICE (Single ody Style) Stainless Steel T Trim Standard Stainless Steel Floats Guaranteed Fully Ported s - No Restrictions Engineered For Drip Tight Seal
More informationThe PL Series Pressure Air Release Valves. Sizes 1 thru 6 Available Compound Lever System Adjustable Buna-N Rubber Plunger. Crispin.
The PL Series Sizes 1 thru 6 Available Compound Lever System Adjustable Buna-N Rubber Plunger Crispin Since 1905 PL SERIES Functio n Allows air and/or gas to be released from a pressurized liquid system
More informationAIR/VACUUM VALVE AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION
AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION Scope. This specification is intended to cover the design, manufacture, and testing of / in. (3 mm) through 0 in. (00 mm) Air/Vacuum Valves suitable
More informationCrispin Valves Operating Guide. Crispin
Crispin Valves Operating Guide Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 www.crispinvalve.com sales@crispinvalve.com
More informationInstalled on the pump suction, CRISPIN Foot Valves prevent the
Foot Valves Crispin Foot Valves SERIES Valve Function Maintains pump prime upon pump outage Features Resilient seat provides positive shut off Full flow area Stainless steel inlet screen Rugged construction
More informationWater Wastewater Air Valves Check Valves
Water Wastewater ir s Check s Water ir s ir Release ir and Vacuum Combination Vacuum reaker Check s Silent Check Swing Check Two-Door Check Foot Flex Check Wastewater & Sewage ir s ir Release ir and Vacuum
More informationCUSTOM COMBINATION AIR VALVE
INSTALLATION / OPERATION / MAINTENANCE CUSTOM COMBINATION AIR VALVE INTRODUCTION This manual will provide you with the information to properly install and maintain this valve to ensure a long service life.
More informationTilting Disc Check Valve
Figures 123 123½ Tilting heck Valve lass 150 olted ap Figure 123 Figure 123½ utt Weld 2 through 36 inches (50-900 mm) STM 216 Grade W 285 psi @ -20 F to 100 F (20 bar @ -28 to 37 ) of onstruction* Inlet
More informationROBERT H. WAGER COMPANY. Installation, Operation and Maintenance Guide. Models 1500/1500-MC 1700/1750
ROERT H. WGER COMPNY Installation, Operation and Maintenance Guide Models 00/00-MC 00/0 MODELS 00/00-MC/00/0 Installation, Operation and Maintenance Guide Robert H. Wager Company, Inc. 0 Montroyal Road
More informationBACKFLOW PREVENTERS DUAL-CHECK BACKFLOW PREVENTER WITH ATMOSPHERIC VENT T/S-459 Certified to ASSE Standard 1012
CKFLOW PREVENTERS DUL-CHECK CKFLOW PREVENTER WITH TMOSPHERIC VENT T/S-459 Certified to SSE Standard 1012 Certified to CS Standard 64.3 Forged brass construction Threaded or sweat true union end connections
More informationResilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator
Worldwide ontacts www.tyco-fire.com Resilient-Seated Gate Valves with Vertical or ross Wall Post Indicator General Description TYO Resilient-Seated Gate Valves with Vertical and ross Wall Indicators are
More informationResilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator
Worldwide ontacts www.tyco-fire.com Resilient-Seated Gate Valves with Vertical or ross Wall Post Indicator General Description TYO Resilient-Seated Gate Valves with Vertical and ross Wall Indicators are
More informationAIRPRO MAX AIR VALVES. Engineering Creative Solutions for Fluid Systems Since 1901
AIRPRO MAX AIR VALVES Engineering Creative Solutions for Fluid Systems Since 0 TABLE OF CONTENTS AIRPRO MAX AIR VALVES Air Release Valve Data and Sizing Guide... Air Vacuum Valve Data and Sizing Guide...-
More informationKTM Three-Way Floating Ball Valves 2-seats (L-port) and 4-seats (L&T-port) General applications Diverting or mixing fluids
KTM Three-Way Floating all Valves -seats (L-port) and 4-seats (L&T-port) KTM single KTM 3-way ball valve replaces several -way saving valuable space and simplifying piping Features Positive alignment of
More informationThe SWL Series Swing Check Valves Meets AWWA C Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution
The Series Meets AWWA C-508-01 Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick,
More informationModulating Water Valves and Bulb Wells
Modulating Water Valves and ulb Wells PPLITION: These modulating valves regulate the flow of water to the heat exchanger to maintain a desired exiting oil temperature. They open automatically when temperature
More informationilent Silent Operation Proven Performance Cost Effective Silent Check Valves Check Valve
ulletin / Silent Operation Proven Performance Cost Effective ilent Check Silent Check s www.valmatic.com Certified Lead-Free NSF/NSI & 7 Certified Feature Highlights Threaded C F C Globe F C E Wafer F
More informationApproved. Size L H. 3" (76mm) 9-1/2" (241mm) 5-51/64" (147mm) 46. 4" (102mm) 11-1/2" (292mm) 6-45/64" (170mm) 81
pproved. Model: SD-NRV200CV Flanged Ends The Flanged End Check Valves are made of Iron Body, Bolted Bonnet and Horizontal Swing, painted with standard color. Epoxy coated inside and outside to WW C550
More informationW94. Specifications. Protection: Models Temperature Range Capillary Length Sensing Bulb Valve Body Selection
Temperature Model W91 (No Indicating Dial) W94 (Temperature Indicating Dial) Service Water, Steam, Other Liquids Sizes 1/2 4 onnections Threaded, Union Ends, 125# FLG 250# FLG (optional) ody Material 1/2
More informationAir/Gas Vents For automatically venting gases from liquids under pressure. Bulletin No. 451-E
ir/gas Vents For automatically venting gases from liquids under pressure. ulletin No. 451-E Selecting The rmstrong ir/gas Vent With the desired CFM capacity known, find the orifice size required from the
More informationSV73 Cast Iron Safety Valve
Page 1 of 5 TI-S13-25 H Issue 11 ert. No. LRQ 0963008 ISO 9001 SV73 ast Iron Safety Valve Description The SV73 cast iron series valves are built in conformance to Section I and VIII of the SME oiler and
More informationThe TD Series Tilting Disc Check Valve Sizes from 2 to 72 #125 and #250 ratings available 55 seating angle 40% size increase through seat.
The Series Sizes from 2 to 72 #125 and #250 ratings available 55 seating angle 40% size increase through seat Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603
More informationAir Valves Engineering Creative Solutions for Fluid Systems Since 1901
Air s Engineering Creative Solutions for Fluid Systems Since 1901 401 South Highland Avenue Aurora, Illinois 60506-5563 www.henrypratt.com phone: 630.844.4000 Email: moreinfo@henrypratt.com Table of Contents
More informationManufacturing Standards
HEK VLVE heck Valve pplication Swg check valves are designed to close quickly and automatically with positive shut off either horizontal or vertical (flow up) pipe runs. Inherently, swg check valves have
More information2010B. Available Materials Aluminum Carbon Steel Stainless Steel Ductile Iron Special Materials on Application
OVER EQUIPMENT VRE 0 / 00 Series PRESSURE N VUUM RELIEF VLVE The 0/00 protects tanks from damage or deformation, and minimizes emissions to the environment, as well as loss of product due to evaporation.
More informationBooster Pump Control Valve
MODEL 60-7 660-7 ooster Pump Control Valve Simple Hydraulic Operation Low Head Loss Horizontal or Vertical Mounting uilt-in Check Valve Proven Reliable Design The Cla-Val Model 60-7/660-7 ooster Pump Control
More informationD I S T R I B U T E D V A L V E S. NAVCO Series E Resilient Seat Butterfly Valve NAVCO
NVCO Series E Resilient Seat utterfly Valve NVCO SERIES E RESILIENT SET UTTERFLY VLVE Features vailable in sizes 2 in. - 24 in. (50 mm - 600 mm) 200 psi 2 in. - 12 in. (50 mm - 300 mm) 150 psi 14 in. -
More informationVALVE INSERTION WHEN YOU ARE UNDER PRESSURE TO INSTALL A VALVE IN AN OPERATING LINE VALVE INSERTION PAGE QV-2
www.romac.com 1-800-426-9341 WHEN YOU RE UNDER PRESSURE TO INSTLL VLVE IN N OPERTING LINE PGE QV-2 4", 6" or 8" installations in cast iron, ductile iron, /C and some classes of PVC pipe Uses modern resilient
More informationFTV-S (Straight) & FTV-A (Angle Body) Tri-Service Valve
VLVES & ESSORIES FTV-S (Straight) & FTV- (ngle ody) SERVIE REOMMENDTIONS: The Model FTV-S & FTV- is primarily designed for installation in pump discharge piping where it functions as a spring loaded silent
More informationVal-Matic 1/2-3 Well Service Air Valve With Dual Port Throttling Device
Manual No. WSAV-OM1-2 Val-Matic 1/2-3 Well Service Air Valve With Dual Port Throttling Device Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF
More information6SC SERIES MODELS 910F, 910FLW, 920F IRON SWING CHECK VALVE INSTALLATION OPERATION MAINTENANCE GUIDE
6SC SERIES MODELS 910F, 910FLW, 920F IRON SWING CHECK VALVE INSTALLATION OPERATION MAINTENANCE GUIDE DOCUMENT NO.: ES-1495 REVISION LEVEL: A ISSUED BY: Bill Hooks DATE: 09/25/13 APPROVED BY: DATE: APOLLO
More informationINSTALLATION INSTRUCTIONS FOR PISTON TYPE FLUSHOMETER EXPOSED CLOSET AND URINAL INSTALLATIONS
ode No. 0816477 Rev. 0 (04/07) Flushometers INSTLLTION INSTRUTIONS FOR PISTON TYPE FLUSHOMETER EXPOSED LOSET ND URINL INSTLLTIONS loset Flushometer for 1½" Top Spud rown II & rown 111 rown II & rown 115
More informationA single KTM 3-Way ball valve replaces several 2-Way saving valuable space and simplifying piping
single KTM -Way ball valve replaces several -Way saving valuable space and simplifying piping Features Positive alignment of body low out-proof stem Sphericity tolerance of the ball is unsurpassed Reinforced
More informationTechnical Data TYPE A SERIES AIR ADJUSTED PILOT SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 4011 OPERATING PRINCIPLE
Technical Data SD 4011 SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY 12586-2035 TYPE A SERIES AIR ADJUSTED PILOT PRINTED IN U.S.A. SD 4011/9504 Type A or A83 (wt 6 lb) Type A53 or A 85
More informationIFC Series DR Retainerless Dual Disc Check Valves
IF Series DR Retainerless Dual Disc heck Valves 6 1 2 3 4 9 7 8 5 10 Design Features Retainerless design meets industry fugitive emissions control requirements. This design eliminates the potential leak
More informationYARWAY BLOW-OFF VALVES SEATLESS, HARDSEAT AND UNIT TANDEM
YRWY LOW-OFF VLVS STLSS, HRDST ND UNIT TNDM Designed for blow-off service in boiler systems with pressures of 36 psig. FTURS GNRL LICTION low-off service in boiler systems to remove dirt, sediment and
More informationYSB SERIES Y - STRAINER
YS SERIES Y - STRINER ronze Y Strainer to 4 100% merican Made Self-ligning Screen Design vailable NPT or Solder onnection Working Pressure (cold non-shock) 125 psi @ 350 F Steam 400 psi @ 150 F WOG RN
More informationCast Steel Tilting Disc Check Valve
ast Steel Tilting heck Valve Typical Tilting heck Valve Tilting heck Valves consist of a cylindrical housing, with a pivoted circular disc. The pivots are located just above the center of the disc, and
More informationTri-Pro Series. Models / Full HPF50 - (316SS) HPF40 - (WCB) Size: 1/4-4 Pressure Rating: 3000 WOG 1/4-3/ WOG 1-4
FLO TITEE valves & controls Tri-Pro Series Models / Full HPF50 - (316SS) HPF40 - (WCB) Size: 1/4-4 Pressure Rating: 3000 WOG 1/4-3/4 2250 WOG 1-4 TM Page 1 3pc High Performance Fire Safe Valves Models
More informationCast Steel Bolted Cover Swing Check Valves Sizes: 2 thru 24 Pressure Class: 150 thru 1500
Cast Steel olted Cover Swing Check Valves s: 2 thru 24 Pressure Class: 150 thru 1500 Manufactured by Newmans 33 Newco Cast Carbon Steel olted onnet Valves Typical Newco Cast Steel olted Cover Swing Check
More informationSeries 34. Specifications
Series Air Release Valves Stainless Steel T Trim Standard Stainless Steel Floats Guaranteed Easily Serviced Without Removal From Pipeline Working Pressures to 800 PSI Engineered For Drip Tight Seal At
More informationG Series Investment Cast Stainless Steel Ball Valves
G Series Investment ast Stainless Steel all Valves G1 E Reduced port NPT ends to NSI 1.2.1 One piece body lowout-proof stem (Ring lock with 1 /4" to 3 /8", Latch lock with 1 /2" to 2") omplies with NE
More informationNominal Flow Pressure Range Temp. Range Viscosity Range
VIKING UNIVERSL XPD 676 PUMPS - FULL COMPLINCE with PI 676 STNDRDS SERIES 4223X & 4323X Section 633 Page 633.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps Offering Full Compliance with PI 676 Design Standards
More informationTubing, Fittings and Air Handling System Components
Tubing, Fittings and ir Handling System omponents INDEX Tubing 5 METLLI TUING ND FITTINGS FOR IR HNDLING SYSTEMS Standard fittings Special fittings Vacuum system inlet valves Special fabrication services
More informationSPIRA-TROL. ½" to 4" ASME (ANSI) Two-port KEA, KFA and KLA Control Valves
Page 1 of 11 MNGMNT SYSTMS TI-P375-1 Issue 3 SPIR-TROL ISO 91 ½" to 4" SM (NSI) Two-port K, KF and KL ontrol Valves ert. No. LRQ 9638 Description SPIR-TROL is a range of two-port single seat globe valves
More informationTABLE OF CONTENTS FORGING AHEAD OF THE REST
ORGED STEEL VLVES YO Valve Co., Ltd ddress: NO. 111, CaoliRoad, engjing Town,Jinshan District,Shanghai, China. TEL: 86-21-67360922 X: 86-21-67360966 Post Code: 201502 E-Mail: info@yaaovalve.com Website:http://www.yaaovalve.com
More informationVisibility & REliability Sight Flow Indicators & Sight Windows
Visibility & REliability Sight Flow Indicators & Sight Windows Featuring KSF SIHt Flow INDITORS Engineered Liquid Flow Solutions www.kenco-eng.com SIHT FLOW INDITORS KENO Engineering ompany offers a variety
More informationFireLock NXT Actuated Valve with Preaction Trim. System No. Submitted By Spec Sect Para Location Date Approved Date
VNIIPO ME: 248-98-E CSFM: 7770-0531-117 The patent-pending Victaulic Series 769 FireLock NXT Preaction Valve controls the water supply entry into the Preaction system piping and sprinklers. The Preaction
More informationAN ISO 9001 : 2008 COMPANY GLOBE VALVES. Get the edge in process control. Butterfly Valves India Pvt. Ltd.
N ISO 9001 : 2008 OMPNY GLOE VLVES Get the edge in process control utterfly Valves India Pvt. Ltd. Introduction Hi-TEH Manufacturing Programme Valve Type End SME 2 2½ 3 4 5 6 8 10 12 onn. lass DESIGN STNDRD
More information3. Installation and Commissioning 4. Maintenance 5. Spares
INSTLLTION ND MINTENNCE INSTRUCTIONS IM-P305-06 US November 2003 1/2" to 4" (DN15 to DN100) KE41, 43, 61, 63, 71 and 73 NSI Control Valves 1. Safety 2. Technical details 3. Installation and Commissioning
More informationMALE X FEMALE LARGE-PORT BALL VALVE T-900 M x F and T-900 M x F-T
MLE X FEMLE LRGE-PORT LL VLVE T-900 M x F and T-900 M x F-T urable forged brass construction Space-saving male-by-female end connections are ideal for confined piping installations T-handle equipped models
More informationParts List Recessed Laboratory Units
Recessed Laboratory Units Item Part Number Description C P470-021LDC FS-Plus Spray Head P450-048 10 Dia. Stainless Steel Shower Head P450-062 P450-016 10 Dia. Recessed Flanged Stainless Steel Shower Head
More informationElectronic Globe Valve Guide Specifications
Electronic Globe Valve Guide Specifications Two and Three-Way Screwed Valves Valves 1/2" through 2" shall be bronze body, NPT screw type, and shall be rated for NSI Class 250 working pressure. The operating
More informationAir Valves. Patent Pending. Engineering Creative Solutions for Fluid Systems Since 1901
Air Valves Patent Pending Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the
More informationVALVULAS. Modelo 215V, 337 Sección VIII, Vacío De Asme Aire/Gas, Válvulas De Seguridad Certificadas Tarjeta Nacional ' UV'
VLVULS Modelo 215V, 337 Sección VIII, Vacío De sme ire/gas, Válvulas De Seguridad Certificadas Tarjeta Nacional ' UV' Descripciones Modelo Model 337: Tiene dispositivo para la elevación 'tirar-anillo'
More informationVal-Matic 1-4 Combination Air Valve (Single Housing Type)
Manual No. ARCO-OM1-3 Val-Matic 1-4 Combination Air Valve (Single Housing Type) Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1
More informationBooster Pump Control Valve
MODEL 60-7 (Full Internal Port) 660-7 (Reduced Internal Port) ooster Pump Control Valve Simple Hydraulic Operation Low Head Loss Horizontal or Vertical Mounting uilt-in Check Valve Proven Reliable Design
More informationValves & Flow Control Components Valves & Flow Control Components
Section 4 Valves & Flow ontrol omponents Valves & Flow ontrol omponents... 106 SJ-200 Low-Profile utterfly Valve... 107 SJ-300N utterfly Valve... 108 SJ-300F utterfly Valve (for Fire Protection)... 110
More informationMaximum leakage rate is less than half of the AWWA allowable Can be adapted to any channel Low-maintenance gates ***
Maximum leakage rate is less than half of the WW allowable Can be adapted to any channel Low-maintenance gates *** The Fontaine gate is designed to control water flows in channels. It is the same construction
More informationGP 300 Grooved Butterfly Valve
GP 300 Grooved utterfly Valve Nominal Pressure: 20 ar ydraulic Shell Test Pressure 30 ar ydraulic Seat Test Pressure 22 ar 20 ar at: 10º to 100º Suitable Media: Water, Oil, Gas 65 80 100 150 Pipe O/ Item
More informationD-023 PN 16 / 25. Combination Air Valve for Wastewater PATENTED. Description. Applications. Operation. Main Features
PN 16 / 25 Wastewater Combination Air Valve for Wastewater PATENTED EuroC-D023SWG-15-2 Description The D-023 Combination Air Valve combines an air & vacuum component and an air release component in a single
More informationAppendix E Head and Valve Assembly Details All D-Style Models 351
Appendix E Hed nd Vlve Assemly Detils All D-Style Models FD Hed Vlve Holddown Assemlies Suction (spec P) 0 0 Suction (spec P) 0 0 Dischrge (ll specs) 0 WFD Hed Appendix E Hed nd Vlve Assemly Detils All
More informationSection 3. Stainless Steel Series. Shurjoint Stainless Steel Piping Series Grooved Mechanical Couplings. Cast Grooved Fittings.
Section 3 Stainless Steel Series Shurjoint Stainless Steel Piping Series... 84 Grooved Mechanical ouplings SS-5 Rigid oupling... 85 SS-7 Rigid oupling... 86 SS-7X Rigid oupling... 87 SS-8 Flexible oupling...
More informationKnife gate valves Index
Index General information page Introduction 144 Product information page ast Iron/SS; Uni-directional 146 ast Iron/SS; i-directional; Throught conduit 147 ast Iron/SS; i-directional 148 ast Iron/SS; Silo
More informationTechnical Data P3 PISTON POWER PUMP NON-ELECTRIC CONDENSATE PUMP SD 9952B
Technical Data SD 9952B SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NEW YORK, 12586-2035 P3 PISTON POWER PUMP NON-ELECTRIC CONDENSATE PUMP Pressures To 250 PSIG (20.7 barg) Temperatures
More informationVB-9313 Series. Application. Features. Applicable Literature
V-9313 Series 2-1/2" and 3" Screwed NPT 2-1/2" to 6" 125 Lb. Flanged Three-Way Mixing s General Instructions pplication V-9313 series three-way mixing valves control hot or chilled water in heating or
More informationHIGH PERFORMANCE SEGMENTED V-BALL CONTROL VALVE
HIGH PERFORMNE SEGMENTE V-LL ONTROL VLVE GENERL INFORMTION HIGH PERFORMNE SEGMENTE V-LL ONTROL VLVE High Rangeability: 300:1 Turn down ratio Flow haracteristic: Equal Percentage Low Pressure Recovery Rate:
More informationVG2000 Series Cast Iron Flanged Globe Valves
Installation Instructions VG2000 Issue ate November 15, 2002 VG2000 Series ast Iron Flanged Globe Valves pplication VG2000 Series ast Iron Flanged Globe Valves are primarily designed to regulate the flow
More informationAN ISO 9001 : 2008 COMPANY SWING CHECK VALVE. Get the edge in process control. Butterfly Valves India Pvt. Ltd.
N ISO 9001 : 2008 COMPNY SWING CHECK VLVE Get the edge in process control utterfly Valves India Pvt. Ltd. Introduction Hi-TECH Manufacturing Programme Valve Type End SME 2 2½ 3 4 5 6 8 10 12 14 16 18 20
More informationVISCOSITY RANGE GPM m 3 h PSI Bar F C SSU cst
UNIVERSL PRODUCT LINE: SERIES 724, 4724 Section 1706 Page 1706.1 Issue B TBLE OF CONTENTS Features & Benefits...2 Cutaway View & Pump Features...2 Model Number Key...3 Standard Materials of Construction...3
More informationWastewater Combination Air Valve. Operation, Maintenance and Installation Manual
Manual No. WCAV-OM1-1 Wastewater Combination Air Valve Operation, Maintenance and Installation Manual INTRODUCTION... 2 RECEIVING AND STORAGE... 2 DESCRIPTION OF OPERATION... 2 INSTALLATION... 3 VALVE
More informationMODEL CB800 Circuit Balancing Valves
MOEL 00 ircuit alancing Valves VLVES & ESSORIES Model 00 ircuit alancing Valves are designed to achieve accurate and efficient balancing of hydronic heating or cooling systems. ircuit alancing Valves provide
More informationG lobe Style Check Valves are designed to close before the
GC SERIES 2 GC Service Applicatio ns Mnicipal Water Systems Indstrial Class HVAC-Liqid Service Indstrial Piping Systems Irrigation Systems Pressre/ Temperatr e Rating Maximm Temperatre Rating: 150ÞF (65ÞC)
More informationAppendix E D791 and T791 Head and Valve Holddown Assembly Details
Appendix E D nd T Hed nd Vlve Holddown Assemly Detils Hed First Stge Holddown Assemly (") Suction with Unloder Suction (Stndrd) First Stge Holddown Assemly (") Dischrge See figure A 0 CAUTION: Alwys relieve
More informationForged Steel Bolted & Welded Bonnet Gate Valves Sizes: 1/4 thru 3 Pressure Class: 150 thru 4500
Forged Steel olted & Welded onnet Gate Valves s: 1/4 thru 3 Pressure lass: 150 thru 4500 Manufactured by Newmans Rev: 052109 13 Typical Newco Forged Steel olted & Welded onnet Gate Valve Expanded View
More informationDIMENSIONS (approximate)
Page 1 of 8 a NRS GATES OS&Y GATES company Model 48 Resilient Wedge Gate Valve SPECIFICATION SUBMITTAL SHEET FEATURES Sizes: 2 1/2" 3" 4" 6" 8" 10" 12" Maximum working water pressure 200 PSI Maximum working
More informationSTEAM TRAPS. Float and Thermostatic Steam Traps (continued) Series C and X. Dimensions in. (mm)
STM TRPS loat and Thermostatic (continued) Series and X or large high capacity units s available: Series : 1 1 /4" NPT and SPT 1 1 /2" NPT and SPT 2" NPT and SPT 2 1 /2" NPT Series X: 2" NPT Resistant
More informationMark 95 Series. Sanitary Valves Mark 95 Sanitary Back Pressure Regulators. Sanitary Back Pressure Regulators. Features
Mark 95 Series Sanitary ack Pressure Regulators The Mark 95 is available with a hard or soft seat and a variety of diaphragm and o-ring materials, making the valve well-suited for virtually any sterile
More informationSuction Guide & Flo-Trex Valve Series
Suction Guide & Flo-Trex Valve Series Pump Trim FILE NO: 6-1 DATE: August 2010 SUPERSEDES: 6-1 DATE: July 200 Series SG & FTV Suction Guides Designed for direct mounting on the suction flange of horizontal
More informationFORGING AHEAD OF THE REST
Bonney orge The Name You Trust for orged Steel Valves Bonney orge's forged steel valves and piping components have led the way for over eighty years in state-ofthe-art design and dependable performance.
More informationS, M, L, and 31 Series. Straight-pattern flow coefficients (C v ) from to Low- and high-pressure service
www.swagelok.com Metering Valves S, M, L, and Straight-pattern flow coefficients (C v ) from 0.004 to 0.16 Low- and high-pressure service Repeatable vernier handles available rass and 316 stainless steel
More informationIron Check Valves Illustrated Index
Iron Check Valves Illustrated Index Iron Body Swing Check Valve Bronze Mounted or All Iron 125 lb. SWP 200 lb. CWP Iron Body Swing Check Valve Bronze Mounted 250 lb. SWP 500 lb. CWP Iron Body Silent Check
More informationSection 8 AMERICAN. Flanged Pipe
Section 8 AMERICAN Flanged Pipe The principal standards covering Flanged Pipe are ANSI/AWWA C115/A21.15 and ANSI/AWWA C110/A21.10. These and other standards are referenced throughout this Section either
More informationOIL & WATER VALVES TREATER VALVE
TREATER VALVE APPLICATIONS: As oil or water valve for emulsion treaters, water knockouts and gunbarrels. Can be used for pressure, atmospheric, or vacuum operation. Ideal for discharging salt water to
More informationBC SERIES CHECK VALVE
SERIES HEK VLVE Soft ubble Tight 1/2 psi racking Pressure NR Standard (Viton Optional, use Suffix V) Lead Free option, use suffix LF omplies with alifornia 1953 Max Working Pressure 1/4 thru 400 psi WOG
More informationModel SCV (Angle Body)
Model SV (ngle ody) Providing extended service life, precise flow control, ease of maintenance and operational reliability in the most challenging applications Features The standardized forged body and
More informationD-040 PN 16 D-040-C PN 16. Combination Air Valve. Description. Applications. Operation. Main Features
D00.WTR.CAT.ENG0 D-00 PN 1 Water Supply D-00-C PN 1 Combination Air Valve Description The D-00 series Combination Air Valve has the features of both an air release valve and an air & vacuum valve. The
More informationKF O-Ring & Packed Stem Style Needle Valves
KF O-Ring & Packed Stem Style Needle Valves KF Needle Valves combine rugged construction, dependability and leak-free performance at high and low pressures. These valves offer exceptional regulating properties
More informationP95H Regulator Applications P95H Part Matrix Specifi cations Materials of Construction P95H Flow Coeffi cients Wide Open Coeffi cients
PH Regulator Large Capacity Working Media Include ir, Steam and Liquids ll Vents are Tapped The PH is a direct operating pressure reducing regulator with large capacity. Ideally suited for uses in oil
More information6D15 DIGESTER CAPPING VALVES
6D15 DIGESTER CPPING VLVES The JMESURY 6D15 digester capping valves provide automatic opening and closing of batch digesters for chip fill. y automating this operation, complete computer control of a batch
More informationGTW 3-WAY CONTROL VALVE SIZES 1/2" 12" ANSI CLASS 125/250, 150/300
GTW ONTROL VLVE PPLITION DT Process control systems for food, pulp and paper, chemical, petrochemical & other industries HV systems Feed water and fuel system controls in boiler rooms Packaged systems
More informationVB-9313 Series. Application. Features. Applicable Literature
V-9313 Series 2-1/2" and 3" Screwed NPT 2-1/2" to 6" 125 Lb. Flanged Three-Way Mixing s General Instructions pplication V-9313 series three-way mixing valves control hot or chilled water in heating or
More information