AIR/VACUUM VALVE AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION
|
|
- Rachel Wade
- 6 years ago
- Views:
Transcription
1 AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION Scope. This specification is intended to cover the design, manufacture, and testing of / in. (3 mm) through 0 in. (00 mm) Air/Vacuum Valves suitable for pressures up to 0 psig (00 kpa) clean or raw water service.. Air/Vacuum valves shall be fully automatic float operated valves designed to exhaust large quantities of air during the filling of a piping system and close upon liquid entry. The valve shall re-open during draining or if a negative pressure occurs. [NOTE: See Air Release Valves for releasing air during system operation and Combination Air Valves for both air release and air/vacuum functions.] Connections. Valve sizes 3 in. ( mm) and smaller shall have full size NPT inlets and outlets equal to the nominal valve size. The body inlet connection shall be hexagonal for a wrench connection.. Valve sizes in. (00 mm) and larger shall have bolted flange inlets with plain outlets and protective hoods to prevent debris from entering the valve. Flanges shall be in accordance with ANSI. for Class or Class 0 iron flanges and ANSI. for Class 0 or Class 300 steel flanges..3 The valve shall have two additional NPT connections for the addition of Air Release Valves, gauges, testing, and draining. Design 3. The valve body shall provide a through flow area equal to the nominal valve size. A bolted cover with alloy screws and flat gasket shall be provided to allow for maintenance and repair. 3. Floats shall be unconditionally guaranteed against failure including pressure surges. The float shall have a hexagonal guide shaft supported in the body by circular bushings to prevent binding from debris. The float shall be protected against direct water impact by an internal baffle. 3.3 The resilient seat shall provide drop tight shut off to the full valve pressure rating. The seat shall be a minimum of. in. ( mm) thick on in. (0 mm) and larger valves and secured in such a manner as to prevent distortion. Valves with working pressures above 00 psig (0 kpa) shall have metal seats with synthetic seals. 3. On valve sizes in. (00 mm) and larger, the cover shall be fitted to the valve body by means of a machined register to maintain concentricity between the top and bottom guide bushings at all times. The float shall be double guided with a guide shaft extending through the float to prevent any contact with the body. A resilient bumper shall be provided to cushion the float during sudden opening conditions. Materials. The valve body, cover, and baffle shall be constructed of ASTM A Class cast iron for Class and Class 0 valves. Class 300 ductile iron valves shall be constructed of ASTM A3 Grade -- ductile iron. Class 300 steel valves shall be constructed of ASTM A Grade WC cast steel.. The float, guide shafts, and bushings shall be constructed of Type 30 Stainless Steel. Non-metallic guides and bushings are not acceptable. Resilient seats shall be una-n. Class 300 steel valves shall have a 30 Stainless Steel Seat with una- N seal to provide an initial contact to una-n with final metal to metal contact to prevent over compression of the resilient seal. Revised -- AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION --0 AL ATIC SS-3 Sheet of
2 AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION Options. An optional Anti-Slam Device, in. (0 mm) and larger, shall be provided when specified to prevent valve pressure surges due to column separation or rapid changes in velocity and pressure... The Anti-Slam Device shall be mounted on the inlet of the Air/Vacuum Valve, allow free air flow in and out of the valve, close upon water entry, and control the inlet water velocity to reduce valve pressure surges... The device shall be a flanged, globe pattern, and spring operated unit with a center guided disc and seat ssembly. The disc shall have threaded holes to provide adjustment of the water flow rate through the valve. The spring shall exert sufficient force to hold the disc open during high air flow conditions and allow the disc to close upon water entry...3 The material of the body shall be consistent with the Air/Vacuum Valve. The spring shall be ASTM A33 Type 30 Stainless Steel. The seat and disc shall be ASTM A3 Grade CFM stainless steel.. A flanged or screwed outlet connection shall be provided when specified for vault piping..3 A stainless steel screened outlet shall be provided when specified for outdoor installations.. Optional body materials include ASTM A3 Grade -- ductile iron, ASTM A3 Grade CFM stainless steel, and ASTM Alloy 3 cast bronze.. Optional float and trim material includes 3 stainless steel. Manufacture. The manufacturer shall demonstrate a minimum of five () years experience in the manufacture of air valves. The valves shall be manufactured and tested in accordance with American Water Works Association Standard (AWWA) C. When requested, the manufacturer shall provide test certificates, dimensional drawings, parts list drawings, and operation and maintenance manuals.. The exterior of the valve shall be coated with a universal alkyd primer..3 Air/Vacuum Valves shall be Series #00 as manufactured by Val-Matic Valve & Mfg. Corporation, Elmhurst, IL. USA. or approved equal. Revised -- AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION --0 AL ATIC SS-3 Sheet of
3 A 3 0 COLD WORKING PRESSURE (CWP) 300 P.S.I. TEST PRESSURE =. TIMES COLD WORKING PRESSURE SEE DRAWING NO. VM-00-M FOR STANDARD MATERIALS OF CONSTRUCTION. MODEL NO. A /" 00 / " " / " N.P.T. / " N.P.T. " 0 " / " " N.P.T. " N.P.T. " 0 / " " " N.P.T. " N.P.T. 3" 03 / " " 3" N.P.T. 3" N.P.T. 3 ODY COVER AFFLE SEAT FLOAT GASKET 0 COVER OLT RETAINING SCREW GUIDE USHING PIPE PLUG GUIDE SHAFT Revised -- AIR/VACUUM -- VM-00
4 AIR/VACUUM / to 3 SERIES NO. 00 STANDARD MATERIALS OF CONSTRUCTION PART NO. 3 * 0 PART NAME ODY COVER AFFLE SEAT FLOAT GASKET COVER OLT RETAINING SCREW GUIDE USHING PIPE PLUG GUIDE SHAFT MATERIAL CAST IRON ASTM A, CLASS CAST IRON ASTM A, CLASS DUCTILE IRON ASTM A3, GRADE -- UNA-N STAINLESS STEEL T30, ASTM A0 COMPRESSED NON-ASESTOS FIER ALLOY STEEL SAE, GRADE STAINLESS STEEL T30, ASTM F3 STAINLESS STEEL T303, ASTM A STEEL STAINLESS STEEL T303, ASTM A * STAINLESS STEEL T30, ASTM F FURNISHED ON NO. 00 ONLY NOTE: ALL SPECIFICATIONS AS LAST REVISED. Revised -- MATERIALS OF CONSTRUCTION // AL ATIC VM-00-M
5 3 A Y L. CLASS (0 CWP) OR 0 L. CLASS (300 CWP) * SEE DRAWING NO. VM-0-M FOR STANDARD MATERIALS OF CONSTRUCTION. ODY COVER SEAT FLOAT GASKET L. " 0 " " 3/ " " FLG. " " 0 " 0" / " " FLG. " " 0" " 0" 3" " / " " " FLG. 0" FLG. " 0" " " 3" 3/ " " FLG. " " " 3" / " " FLG. " " 30 / " 3" / " " FLG. " 0" / " 3 / " / " 0" FLG. 0" AIR/VACUUM 0 L. A COVER OLT RETAINING SCREW GUIDE USHING CUSHION 3 HOOD HOOD RETAINING SCREW WASHER (EXTERNAL) SEAT RETAINING SLEEVE WASHER (INTERNAL) PIPE PLUG SPOOL PIECE REQUIRED WHEN MATING TO A WAFER OR LUG UTTERFLY. SEE DRAWING NO. SS- FOR SPOOL PIECE DETAIL. Revised -30- Y * 3--0 VM-0
6 AIR/VACUUM " - 0" SERIES NO. 00 STANDARD MATERIALS OF CONSTRUCTION PART NO. 3 * PART NAME ODY COVER SEAT FLOAT GASKET COVER OLT RETAINING SCREW GUIDE USHING CUSHION HOOD HOOD RETAINING SCREW WASHER-EXTERNAL SEAT RETAINING SLEEVE WASHER-INTERNAL PIPE PLUG MATERIAL CAST IRON ASTM A, CLASS CAST IRON ASTM A, CLASS UNA-N STAINLESS STEEL T30, ASTM A0 COMPRESSED NON-ASESTOS FIER ALLOY STEEL SAE, GRADE STAINLESS STEEL T30, ASTM F3 STAINLESS STEEL T303, ASTM A UNA-N STEEL - #00 STEEL (ZINC PLATED) STEEL (ZINC PLATED) STAINLESS STEEL T30, ASTM A STAINLESS STEEL T30, ASTM A0 STEEL NOTE: ALL SPECIFICATIONS AS LAST REVISED. * NOT FURNISHED ON S " & " MATERIALS OF CONSTRUCTION // Revised -- VM-0-M
7 A FOR AIR/VACUUM DETAIL SEE VM-0 FOR ANTI-SLAM DEVICE DETAIL SEE VM-00 L. CLASS (0 CWP) OR 0 L. CLASS (300 CWP) DIMENSIONS L. CLASS 0 L. CLASS A 0 0/0 0/0 0/0 0/0 / / / / / / 0/0 / / / 0 30 / / 3 / 3 / / / 3 / / 0 0/0 0/0 3 / / AIR/VACUUM WITH ANTI-SLAM DEVICE AL ATIC Revised VM-0/0
8 A L. CLASS (0 CWP) OR 0 L. CLASS (300 CWP) SEE DRAWING NO. VM-0-M FOR STANDARD MATERIALS OF CONSTRUCTION. " " L. 0S 0S 0 L. S S A " " " 0" " FLG. " FLG. " " ODY COVER SEAT FLOAT GASKET COVER OLT RETAINING SCREW GUIDE USHING CUSHION SEAT RETAINING SLEEVE PIPE PLUG AIR/VACUUM WITH SCREWED Revised VM-0S
9 A L. CLASS (0 & 300 CWP) Y L. CLASS (0 CWP) OR 0 L. CLASS (300 CWP) SEE DRAWING NO. VM-0-M FOR STANDARD MATERIALS OF CONSTRUCTION. L. 0 L. A Y * " 0F F " 3" / " " FLG. " 0" 0F 0F 0" " " 0" FLG. 0" " F F " 3" 3/ " " FLG. " " F F " 3" / " " FLG. " " F F 30 / " 3" / " " FLG. " 0" 0F 0F 3 / " 3 / " / " 0" FLG. 0" ODY COVER SEAT FLOAT GASKET COVER OLT RETAINING SCREW GUIDE USHING CUSHION SEAT RETAINING SLEEVE WASHER PIPE PLUG * SPOOL PIECE REQUIRED WHEN MATING TO A WAFER OR LUG UTTERFLY. SEE DRAWING NO. SS- FOR SPOOL PIECE DETAIL. Revised -30- AIR/VACUUM W/ FLANGED AL ATIC -- VM-0F
CUSTOM COMBINATION AIR VALVE
INSTALLATION / OPERATION / MAINTENANCE CUSTOM COMBINATION AIR VALVE INTRODUCTION This manual will provide you with the information to properly install and maintain this valve to ensure a long service life.
More informationilent Silent Operation Proven Performance Cost Effective Silent Check Valves Check Valve
ulletin / Silent Operation Proven Performance Cost Effective ilent Check Silent Check s www.valmatic.com Certified Lead-Free NSF/NSI & 7 Certified Feature Highlights Threaded C F C Globe F C E Wafer F
More informationAIRPRO MAX AIR VALVES. Engineering Creative Solutions for Fluid Systems Since 1901
AIRPRO MAX AIR VALVES Engineering Creative Solutions for Fluid Systems Since 0 TABLE OF CONTENTS AIRPRO MAX AIR VALVES Air Release Valve Data and Sizing Guide... Air Vacuum Valve Data and Sizing Guide...-
More informationSeries 36-WW COMBINATION AIR VALVES DATA AND SIZING WASTEWATER SERVICE. (Single Body Style) Installation. Specifications. Purchase Specification
Series -WW COMINTION IR S DT ND SIZING WSTEWTER SERVICE (Single ody Style) Stainless Steel T Trim Standard Stainless Steel Floats Guaranteed Fully Ported s - No Restrictions Engineered For Drip Tight Seal
More informationAir Valves Engineering Creative Solutions for Fluid Systems Since 1901
Air s Engineering Creative Solutions for Fluid Systems Since 1901 401 South Highland Avenue Aurora, Illinois 60506-5563 www.henrypratt.com phone: 630.844.4000 Email: moreinfo@henrypratt.com Table of Contents
More informationDos Rios Chlorine Contact Basin Scum Well Rehabilitation Project Solicitation Number: CO Job No.:
Dos Rios Chlorine Contact Basin Scum Well Rehabilitation Project Solicitation Number: CO-00031 Job No.: 15-6504 To Respondent of Record: ADDENDUM I November 20, 2015 This addendum, applicable to work referenced
More informationIron Check Valves Illustrated Index
Iron Check Valves Illustrated Index Iron Body Swing Check Valve Bronze Mounted or All Iron 125 lb. SWP 200 lb. CWP Iron Body Swing Check Valve Bronze Mounted 250 lb. SWP 500 lb. CWP Iron Body Silent Check
More informationVal-Matic 4-20 Air/Vacuum Valve
Manual No. A/VV-OM2-4 Val-Matic 4-20 Air/Vacuum Valve Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION... 2 VALVE CONSTRUCTION...
More informationWafer and Globe Style Silent Check Valve. Operation, Maintenance and Installation Manual
Manual No. SCV-OM1-4 Wafer and Globe Style Silent Check Valve Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION... 2
More informationSURGEBUSTER! BUILT WITH ADVANCED TECHNOLOGY TO WITHSTAND YOUR TOUGHEST APPLICATIONS. Air Release Air Valves. Air/Vacuum Air Valves
V SURGEBUSTER! Air Release Air Valves Bulletin 7200 Air/Vacuum Air Valves Combination Air Valves Well Service Air Valves Wastewater Air Valves Anti-Slam Air Valves Vacuum Relief Air Valves A member of
More informationVal-Matic 1/2-3 Well Service Air Valve With Dual Port Throttling Device
Manual No. WSAV-OM1-2 Val-Matic 1/2-3 Well Service Air Valve With Dual Port Throttling Device Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF
More informationThe SC Series Surge Check Valves Sizes 3 thru 24 Available Cast Iron Construction Limits the Effects of System Surge on Air Release Valves.
The Series Sizes 3 thru 24 Available Cast Iron Construction Limits the Effects of System Surge on Air Release Valves Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA
More informationAir Valves. Patent Pending. Engineering Creative Solutions for Fluid Systems Since 1901
Air Valves Patent Pending Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the
More informationThe SWL Series Swing Check Valves Meets AWWA C Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution
The Series Meets AWWA C-508-01 Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick,
More informationSWING CHECK VALVES SERIES 52-SC SERIES 600
SWING CHECK VALVES SERIES 52-SC SERIES 600 FEATURES/BENEFITS/SPECIFICATIONS AMERICAN Flow Control Series 52-SC Swing Check Valves incorporate design features to help increase service life for water and
More informationSuction Guide & Flo-Trex Valve Series
Suction Guide & Flo-Trex Valve Series Pump Trim FILE NO: 6-1 DATE: August 2010 SUPERSEDES: 6-1 DATE: July 200 Series SG & FTV Suction Guides Designed for direct mounting on the suction flange of horizontal
More informationM&H AWWA C508 STANDARD SWING CHECK VALVES
GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by
More informationInstalled on the pump suction, CRISPIN Foot Valves prevent the
Foot Valves Crispin Foot Valves SERIES Valve Function Maintains pump prime upon pump outage Features Resilient seat provides positive shut off Full flow area Stainless steel inlet screen Rugged construction
More informationSECTION VALVES AND OPERATORS
SECTION 15200 VALVES AND OPERATORS PART 1 - GENERAL 1.1 SUBMITTALS A. Shop Drawings: 1. Product data sheets for make and model. 2. Complete catalog information, descriptive literature, specifications,
More informationM&H AWWA C508 STANDARD SWING CHECK VALVES
GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by
More informationVal-Matic 1-4 Combination Air Valve (Single Housing Type)
Manual No. ARCO-OM1-3 Val-Matic 1-4 Combination Air Valve (Single Housing Type) Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1
More informationSECTION MISCELLANEOUS VALVES
SECTION 05140 - PART 1 - GENERAL 1.1 WORK OF THIS SECTION A. The WORK of this Section includes providing miscellaneous valves as indicated, complete and operable, including accessories and operators. 1.2
More informationSurgebuster Check Valves
Bulletin 7200 Innovative Design Optimum Performance Advanced Technology SURGEBUSTER! Surgebuster Check Valves www.valmatic.com AWWA C508 Certified NSF/ANSI 61 Certified for Drinking Water NSF/ANSI 372
More informationSuggested Specifications
ISO 9001 Certified Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve, setting higher standards for dependable performance
More informationG. VULCANIZED SEAT Pressure sensitive seating with full disc overlap provides positive seating at high and low pressures.
SOLTECH LTDA Tecnologías e Ingeniería de Control A B C D G F E J H I A. RETAINER PLUGS Retain hinge and stop pins while providing compression to stabilization spheres. B. STABILIZATION SPHERES Stabilize
More informationMILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE
ISO 9001 CERTIFIED MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve,
More informationCheck Valve MODEL. Schematic Diagram. Product Dimensions Data:
Check Valve Simple Proven Design No-Slam Operation Drip-Tight Shut-Off No Packing Glands or Stuffing Boxes Easy to Install & Maintain 8-0 (Full Internal Port) MODEL 68-0 (Reduced Internal Port) The Cla-Val
More informationTitan Check Valves. Call. Fax. . Visit. Titan Flow Control. Your Pipeline to the Future
Your Pipeline to the Future TITAN 290 Corporate Drive Lumberton, NC 28358 Titan Check Valves, Inc. is a high quality manufacturer of check valves. With a dedication to great customer service, cutting edge
More information2-12 Grooved End Dual Disc Check Valve. Operation, Maintenance and Installation Manual
Manual No. DDCV-OM4-1 2-12 Grooved End Dual Disc Check Valve Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION... 2
More informationThe Universal Sewer Air Release Valve is designed to permit
Universal Sewer Valves Universal Sewer Valves Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Allows accumulating air to escape while line is in operation Features
More information½"-3" Air/Vacuum Valve Models 100S to 103S
Manual No. A/VV-OM1-4 ½"-3" Air/Vacuum Valve Models 100S to 103S Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION...
More informationVal-Matic 1-4 Combination Air Valve (Single Housing Type)
Manual No. ARCO-OM1-2 Val-Matic 1-4 Combination Air Valve (Single Housing Type) Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1
More informationCrispin. The UL Series Universal Air Release Valves. Compound Lever System NPT Screwed or ANSI Class Flanges Available.
The UL Series Universal Air Release s Compound Lever System NPT Screwed or ANSI Class Flanges Available Crispin Since 105 sales@crispinvalve.com Universal Air Release s Universal Air Release UL SERIES
More informationMETAL SEATED BALL VALVE Engineering Creative Solutions for Fluid Systems Since 1901
METAL SEATED BALL VALVE Engineering Creative Solutions for Fluid Systems Since 1901 TABLE OF CONTENTS PRATT METAL SEATED BALL VALVE Introduction... 1 Scope of Line... 2 Features and Benefits... 2 Suggested
More informationValve Selection. 1. Function and service considerations
1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.
More informationWater Wastewater Air Valves Check Valves
Water Wastewater ir s Check s Water ir s ir Release ir and Vacuum Combination Vacuum reaker Check s Silent Check Swing Check Two-Door Check Foot Flex Check Wastewater & Sewage ir s ir Release ir and Vacuum
More informationAPCO SLANTING DISC CHECK VALVES
BULLETIN 800 JULY 2011 APCO SLANTING DISC CHECK VALVES Series 800, 800B, 800T APCO Slanting Disc Check Valve With decades of experience to guarantee reliability and outstanding performance, our Slanting
More informationKunkle Models 91/218/228 liquid relief valves Safety and relief products
Cast iron liquid relief valves with bronze trim including models UL and FM approved for fire pump installations Model 228 Features Bolted bonnet allows easy inspection and servicing without removal from
More informationKunkle Models 91/218/228 liquid relief valves Safety and relief products
Cast iron liquid relief valves with bronze trim including models UL and FM approved for fire pump installations Model 8 Features Bolted bonnet allows easy inspection and servicing without removal from
More informationVacuum Relief Performance Curves
Vacuum Relief Valves Crispin Vacuum Relief Valves Valve Function llows air to enter system when vacuum occurs Prevents air exhaustion during pump start-up Features Cracks open to admit air at.25 PSIG differential
More informationD I S T R I B U T E D V A L V E S. NAVCO Series E Resilient Seat Butterfly Valve NAVCO
NVCO Series E Resilient Seat utterfly Valve NVCO SERIES E RESILIENT SET UTTERFLY VLVE Features vailable in sizes 2 in. - 24 in. (50 mm - 600 mm) 200 psi 2 in. - 12 in. (50 mm - 300 mm) 150 psi 14 in. -
More informationAPCO SURGE RELIEF ANGLE VALVES (SRA)
BULLETIN 3000 MARCH 2018 APCO SURGE RELIEF ANGLE VALVES (SRA) Design & Construction APCO Surge Relief Angle Valves (SRA) are designed to limit surge pressure and the potential damage to the pump system.
More information14 and Larger Wafer and Lug Style Dual Disc Check Valve. Operation, Maintenance and Installation Manual
Manual No. DDCV-OM2-2 14 and Larger Wafer and Lug Style Dual Disc Check Valve Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION...
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class 150/250 December 2012
SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class December 2012 1. SCOPE This product specification covers class rubber-seated butterfly
More informationAir and Vacuum Sewer Valves. Stainless Steel Trim Standard. Short Air & Vacuum Sewer Series
ir and Vacuum Sewer Valves ir and Vacuum Sewer Valves Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Features Include Standard and short body series available vailable
More informationCrispin Valves Operating Guide. Crispin
Crispin Valves Operating Guide Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 www.crispinvalve.com sales@crispinvalve.com
More informationFLOAT CONTROL VALVES
PROJECT NAME LOCATION FLOAT CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 8 in. (200 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard
More informationMODULATING FLOAT CONTROL VALVE
PROJECT NAME LOCATION MODULATING FLOAT CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
More information15100 VALVES. E. Section Building Automation and Control System Guidelines
15100 VALVES PART 1: GENERAL 1.01 RELATED SECTIONS A. Section 15050 Basic Material and Methods B. Section 15545 Chilled Water System C. Section 15550 Heat Generation D. Section 15790 Coils E. Section 15955
More informationWastewater Combination Air Valve. Operation, Maintenance and Installation Manual
Manual No. WCAV-OM1-1 Wastewater Combination Air Valve Operation, Maintenance and Installation Manual INTRODUCTION... 2 RECEIVING AND STORAGE... 2 DESCRIPTION OF OPERATION... 2 INSTALLATION... 3 VALVE
More informationThe applicable material specifications for ductile iron and rubber gaskets apply:
72 COUPLINGS - Grinnell Copper Grooved System is designed for joining copper tube size components 2" to 8" (54,0mm to 206,4mm) type K, L, M and DWV. All couplings and fittings are rated for working pressures
More informationModel descriptions. 2. For other pressure and temperature limits, consult ANSI B16 cast iron flange standards.
VALVES & CONTROLS KUNKLE SAFETY AND RELIEF PRODUCTS Cast Iron Liquid Relief Valves Model 228 Model descriptions Model 91: Bronze trim, with pressure-tight cap. Suitable for maximum back pressure of 60
More informationUS SERIES. Universal Sewer Valves. Universal Sewer Valves. Valve Function. Features Include
Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Allows accumulating air to escape while line is in operation Features Include Standard and short body series available
More informationPRESSURE RELIEF / SUSTAINING CONTROL VALVES
PROJECT NAME LOCATION PRESSURE RELIEF / SUSTAINING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART
More informationPRESSURE REDUCING CONTROL VALVE
PRESSURE REDUCING CONTROL VALVE 06/08 Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) X P/L Standard Components 1 Main
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. Provide labor, materials, equipment, and services necessary to install valves required to complete the work indicated on drawings. B. ASME Compliance: 1. ASME
More informationSpecifications For Valve Insertion System
Specifications For Valve Insertion System Equipment For Valve Insertion Pipe Sizes: 4 (100mm) Through 12 (300mm) 1.0 SCOPE This specification covers the furnishing, complete EZ Valve insertion system.
More informationCast Steel Valves. General Index. Figure Number Index JENKINS -1-
Cast Valves Cast Valves SINCE 1864 General Index General Data... 2 Materials... 2 Identification... 3 Gate Valve Features... 4, 5 Globe Valve Features... 9, 10 Swing Check Valve Features... 14, 15 Pressure/Temperature
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 230523 GENERAL DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. The following
More informationSECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000
More informationSUBMITTAL PACKAGE FIRE PROTECTION VALVES
SUBMITTAL PACKAGE FIRE PROTECTION VALVES Butterfly Valves Ductile Iron Grooved...pg 2-5 Grooved Check Valves...pg 6-8 OS&Y Valves...pg 9-12 ARGCO.com 800-854-1015 Updated 2/27/2017 ARGCO GROOVED BUTTERFLY
More informationHerpteraium SECTION VALVES GENERAL
SECTION 22 05 23 VALVES GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to
More informationALTITUDE CONTROL VALVES FOR ONE WAY FLOW
PROJECT NAME LOCATION ALTITUDE CONTROL VALVES FOR ONE WAY FLOW INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1
More informationHinge Pin. 7 Bearing. Spring Plate. Spring. Disc. Body. Gasket. Stop PIn
Hinge Pin Bearing Spring Plate Spring Disc Body Gasket Stop PIn TYPICAL MATERIAL OF MAIN PARTS No. Part Name Carbon Steel Stainless Steel Alloy Steel 1 Stop Pin 2 Gasket 3 Body 4 Disc 5 Spring 6 Spring
More information6SC SERIES MODELS 910F, 910FLW, 920F IRON SWING CHECK VALVE INSTALLATION OPERATION MAINTENANCE GUIDE
6SC SERIES MODELS 910F, 910FLW, 920F IRON SWING CHECK VALVE INSTALLATION OPERATION MAINTENANCE GUIDE DOCUMENT NO.: ES-1495 REVISION LEVEL: A ISSUED BY: Bill Hooks DATE: 09/25/13 APPROVED BY: DATE: APOLLO
More informationInnovative Products For Unique Applications. A Tradition of Excellence. Creative Engineering for Fluid Systems
page 1 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry Pratt Company became a trusted name in the flow control industry, setting
More informationPRESSURE REDUCING CONTROL VALVES
PROJECT NAME LOCATION PRESSURE REDUCING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
More informationPRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE
PROJECT NAME LOCATION PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2-1/2 in. (65 mm) through 18 in. (450 mm) Control
More informationStainless Steel Trim Standard. ir and Vacuum Sewer Valves permit a large volume of air to
ir and Vacuum Sewer Valves Valve Functio n Exhausts air as a pipeline fills, and allows air in as pipeline drains Features Include Standard and short body series available vailable in sizes thru 10 ll
More informationD-023 PN 16 / 25. Combination Air Valve for Wastewater PATENTED. Description. Applications. Operation. Main Features
PN 16 / 25 Wastewater Combination Air Valve for Wastewater PATENTED EuroC-D023SWG-15-2 Description The D-023 Combination Air Valve combines an air & vacuum component and an air release component in a single
More informationSeries SG & FTV. Suction Guides & Flo-Trex Valves
Series SG & FTV Suction Guides & Flo-Trex Valves File no.: 35.11l Date: nov. 15, 2013 Supersedes: 35.11in Date: february 05, 2013 Series SG & FTV Suction Guides Designed for direct mounting on the suction
More informationCopyright 2016 AIA MasterSpec Premium 12/16 PRODUCT MASTERSPEC LICENSED BY ARCOM TO CONBRACO, INC.
This Product MasterSpec Section is licensed by ARCOM to Apollo Flow Controls, Conbraco Industries, Inc ("Licensee").This Product MasterSpec Section modifies the original MasterSpec text and does not include
More informationThe TD Series Tilting Disc Check Valve Sizes from 2 to 72 #125 and #250 ratings available 55 seating angle 40% size increase through seat.
The Series Sizes from 2 to 72 #125 and #250 ratings available 55 seating angle 40% size increase through seat Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603
More informationCLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION
CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION TESTING AND DESIGN SPECIFICATIONS (PER AWWA C502 / NSF /ULC & FM) 1. Hydrant shall be manufactured in accordance with AWWA C502 latest revision
More informationDARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15100 VALVES PART 1 DESIGN DIRECTIVE 1.1 SUMMARY A. This Section includes general duty valves common to most mechanical piping systems, special duty valves are specified in individual piping system
More informationSOLENOID CONTROL VALVE
PROJECT NAME LOCATION SOLENOID CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 4 in. (100 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard
More informationAWWA SWING CHECK VALVES. Engineering Creative Solutions for Fluid Systems Since 1901
AWWA SWING CHECK VALVES Engineering Creative Solutions for Fluid Systems Since 1901 TABLE OF CONTENTS AWWA SWING CHECK VALVE Series 8001 Lever & Weight or Spring...1 Series 9001 Lever & Weight or Spring...2
More informationThe PL Series Pressure Air Release Valves. Sizes 1 thru 6 Available Compound Lever System Adjustable Buna-N Rubber Plunger. Crispin.
The PL Series Sizes 1 thru 6 Available Compound Lever System Adjustable Buna-N Rubber Plunger Crispin Since 1905 PL SERIES Functio n Allows air and/or gas to be released from a pressurized liquid system
More informationMetal Seated Ball Valve
Metal Seated Ball Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry
More informationAMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE
AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE CONSTRUCTION STAINLESS STEEL PIPE PLUG Allows installation of pressure gauge. STAINLESS STEEL FASTENERS Helps provide corrosion resistance.
More informationSECTION 1019 VALVES AND APPURTENANCES GENERAL: Valves shall have manufacturer's name and pressure rating cast in raised letters.
SECTION 1019 VALVES AND APPURTENANCES Delete this Section in its entirety and replace with the following: SECTION 1019 VALVES AND APPURTENANCES 1019-1 GENERAL: Valves shall have manufacturer's name and
More informationGENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.
More informationPRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Closes quickly when downstream pressure exceeds reduced pressure setpoint 3 PRESSURE REDUCING VALVE with SURGE
More informationSECTION VALVES
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SUNY GENESEO 220523-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION GENERAL-DUTY VALVES FOR HVAC PIPING. A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section.
SECTION 23 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Gate Valves 2. Balancing Valves 3. Ball Valves 4. Butterfly Valves 5. Swing Check Valves 1.2 RELATED SECTIONS A. Contents of Division
More informationKUNKLE MODELS 19/19M/20/20M/20P/20MP/200A/200H LIQUID RELIEF VALVES SAFETY AND RELIEF PRODUCTS
Extra-heavy rugged construction non-code bronze liquid relief valves with a variety of model options to meet specific applications FEATURES Inlet and outlet connections cast integral with body for easy
More informationSECTION SWING CHECK VALVES
PART 1 GENERAL 1.1 DESCRIPTION This section includes materials, testing, and installation of swing check valves as shown in the Drawings and specified herein, in accordance with the requirements of the
More informationAWWA C515 REDUCED WALL DUCTILE IRON
30" - 54" R/W VALVES AWWA C515 Resilient Wedge Gate Valves Meet or Exceed the Requirements of AWWA Standard C515 Water Working Bubble Tight Hydrostatic Shell Size Range Pressure psi Test psi Test psi AWWA
More informationData Sheet Issue A
General Description The Rapidrop Fig 601/602 dry barrel post / flushing fire hydrant is designed to be a trouble free, easy to maintain hydrant. The Fig 601/602 fire hydrant is rated for a working pressure
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationCCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901
CCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry
More informationCOMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES 2.01 COMBINATION RESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVE
PROJECT NAME LOCATION COMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900
More informationAMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available Listed by Underwriters Laboratories Inc. and Approved by FM Approvals in applicable
More informationSECTION VALVES PART 1 -GENERAL
SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This
More informationVALVES. A. Section HVAC Basic Materials and Methods. E. Section Building Automation and Control System Guidelines
230523 VALVES PART 1: GENERAL 1.01 RELATED SECTIONS A. Section 230500 HVAC Basic Materials and Methods B. Section 230510 Chilled Water System C. Section 230520 Heat Generation D. Section 238216 Coils E.
More informationHeavy welded steel outlet half. 3/4-inch NPT test plug. Benefits
622 Tapping Sleeve Recessed cavity for mating to lip on standard tapping valves per MSS SP60. Heavy welded steel outlet half. 3/4-inch NPT test plug. Roll resistant, self-energizing concave wedge gasket.
More informationGate Valves Globe Valves Check Valves. The Valve Experts IRON VALVES
Gate Valves Globe Valves Check Valves The Valve Experts IRON VLVES Iron Valves Index General Data... 5 Materials... 6 Pressure/Temperature Ratings... 7 C V Coefficients... 8 Gate Section... 9 Globe Section...
More information1 Visit for more details. Contact the Factory at
PACIFIC Fire Protection Solutions for Offshore and Onshore Applications Deluge Pressure Relief Pressure Reducing Level Control Solenoid Control Air Release and Check Valves 1 Visit www.cla-valpacific.com
More information