Tube Cleaners Introduction
|
|
- Linette Shields
- 5 years ago
- Views:
Transcription
1 Tube Cleaners Introduction Clean tubes mean lower fuel costs. All piping, heat echangers, condensers, chillers, and boiler tubes accumulate scale over various periods of use. This scale decreases flow and retards heat transfer. This consequently increases fuel consumption which lowers overall efficiency. Scale /50 in. thick, approimately 5% additonal fuel required. Scale /25 in. thick, approimately 0% additional fuel required. Scale /6 in. thick, approimately 5% additional fuel required. a boiler tube showing etra fuel required due to scale of VARIOUS thicknesses. Scale /8 in. thick, approimately 30% additional fuel required. Scale /4 in. thick, approimately 66% additional fuel required. Scale /2 in. thick, approimately 50% additional fuel required. /2 inch scale in 6 inch pipe, 000 feet long, has a transfer capacity loss of 50 gallons per minute. For selecting the proper Airetool tube cleaner components the following information is required: Tube ID Tube length Type of deposit Thickness of deposit Straight or curved tube If curved, the minimum bend radius (see charts) Rigid shaft cleaning systems for straight tubes in heat echangers and condensers are shown on pages Fleible shaft cleaning systems for straight and curves tubes in condensers, chillers, evaporators and other tubular heat transfer apparatus are shown on pages 909. Refer to the overview of motors and cleaning heads based on tube scale thickness and composition on pages 92 (straight tubes) and 93 (curved tubes), then use the selection guide on pages 9497 that match boiler tube cleaning motors and heads together. Note: Operating hoses are not included with boiler tube cleaners. It is always recommended to use an inline lubricator and foot valve when operating the Airetool boiler tube cleaners. See page 7 for more information on these accessories. Boiler tube cleaner applications include: Oil field drill pipe renewal Natural gas line renewal Aluminum smelter siphon tube cleaning Catalyst cleaners Process line cleaning Sugar Refinery Transfer line cleaning 84 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
2 Tube Cleaners Heat Echanger & Condenser Cleaning Systems System Components Motors cc475 & cc475ps cc375 cc325 cc325hp s drive coupling drive shaft shaft coupling Drills and Brushes driven shaft ct drill tw drill AT drill cb drill spiral brush Complete Cleaning Systems Complete cleaners consist of an air motor with integral water feed valve couplings; up to 22 ft. of shafting with necessary couplings (please specify shaft length required); motor shaft wrench and an etra set of motor blades. The CC 475 Cleaner Complete includes two drills of any type or size up to, three spiral brushes up to and 5 feet of 3/8 inch water hose. The CC 475PS Cleaner Complete includes two drills of any type or size up to /2", three spiral brushes up to /2" and 5 feet of 3/8 inch water hose. CC375, 325 & 325HP: Includes Ball bearing trolley and rope block. Model Order Lightweight Condenser Cleaners Complete CC CC475PS Geared Drive Cleaners Complete CC375 CC CC325HP PT 5 feet of 3/8 inch Water Hose Water Hose Water Feed Attachment WF Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 85
3 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Cleaning Motors Clean Tubes Equal Higher Operating Efficiencies Airetool lightweight condenser & geared drive cleaners make it easy to maintain your industrial process at a high level of efficiency by providing cleaning motors that are both powerful and durable. Model Order Range.5 RPM Weight Length Air Inlet Operating Air Pressure Water Inlet Ma. Water Pressure lbs. Kg in. mm NPT PSI kg/cm2 NPT PSI kg/cm2 Lightweight Condenser Cleaners CC up to in. (25.4 mm) ID Tubes / / / CC475PS up to /2 in. (38. mm) ID Tubes / / / Geared Drive Cleaners* CC up to 3/4 in. (44.4 mm) ID Tubes / CC up to 2 in. (50.8 mm) ID Tubes / CC325HP up to 2 in. (50.8 mm) ID Tubes / * Water hose not included. Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 86
4 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Components ing components connect the motor to the drill head or brush. Drive s & Driven s come in standard lengths of five and ten foot Other lengths available on request drive coupling drive shaft shaft coupling driven shaft Tube I.D. Drive Drive Drive Driven Diameter For Drive For Drive Length* Drive CC475 CC375 Length* CC475PS Thread CC325 Thread Thread in. mm in. mm 5 ft. 0 ft. Thread 5 ft. 0 ft. & WF00 & CC325HP / / / / / / / * Stand ial lengths available upon request AT337A (2000) AT333A (20000) AT32A (200700) AT33A (200300) AT309A (20000PT) AT30A (9900) AT37A (200500) AT325A (200800) NF NF NF NF NF NF NF 7/6" NF NF /2" NF NF NF NF NF NF NF AT333 (200900) AT352 (20300) AT353 (20400) AT359 (20900) AT35 (20200) AT357 (20800) AT354 (20500) NF NF NF NF NF 7/6" NF NF /2" NF NF NF NF NF NF NF CC3365 (7733) CC3325 (7735) CC3245 (7737) CC365 (7739) CC325 (774) CC3045 (7744) CC3205 (7746) CC3285 (7748) CC3360 (775) CC3320 (7753) CC3240 (7755) CC360 (7757) CC320 (7759) CC3040 (7763) CC3200 (7765) CC3280 (7767) NFM 032 F NFM NFF NFM NFF 7/6" NFM NFF /2" NFM NFF NFM NFF NFM 7/6" NFF NFM 7/6" NFF CC334 (232800) CC330 (232500) CC322 (23900) CC34 (230800) CC30 (230400) CC302 (229500) CC38 (23400) CC326 (232200) 032M CC3355 (7732) NFM CC335 (7734) NFM CC3235 (7736) NFM CC355 (7738) NFM CC35 (7740) NFM CC3035 (7743) 7/6" NFM CC395 (7745) 7/6" NFM CC3275 (7747) CC3350 (7750) CC330 (7752) CC3230 (77540) CC350 (7756) CC30 (7758) CC3030 (7762) CC390 (7764) CC3270 (7766) Driven Thread 032 F 032 F NFF NFF NFF NFF NFF NFF 3/.8" NFF NFF 3/.8" NFF NFF 7/6" NFF 7/6" NFF 7/6" NFF 7/6" NFF Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 87
5 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Drills and Brushes Airetool drills are designed especially to prevent damage to the tube I.D., and are available in a variety of shapes to remove all types of scale deposits. Passages in the drill shaft enable flushing fluid to reach the drill cutting edge. Larger sizes available on request. Type AT standard drill for medium deposits Type CB standard drill ( AT style) for medium deposits with carbide insert for better durability Type CBHP high pressure drills provide better flushing power when used with the CC325HP motor Type TW standard twist drill for thick deposits Type CT standard twist drill ( TW style) for thick deposits with carbide insert for better durability Wire Brushes are for light deposits Minimum order quantities may apply. Tube I.D. Diameter of AT CB CB (Carbide) CT Drill or Brush Stud (Standard) Drills (Carbide) Drills HP Drills* (Carbide Twist) TW Wire Thread Drills (Twist) Drills Brush in. mm in. mm Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) UNC UNC UNC UNC UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF AT99 (92200) AT995 (92300) AT200 (92400) AT2005 (92500) AT20 (92600) AT202 (92700) AT203 (92800) AT204 (92900) AT205 (93000) AT206 (9300) AT207 (93200) AT208 (93300) AT08 (92000) AT209 (93400) AT20 (93500) AT2 (93600) AT22 (93700) * HP Style drills are used for more aggressive cleaning with CC325HP cleaning motor CB99 (220400) CB995 (220500) CB200 (75666) CB2005 (220600) CB20 (220700) CB202 (220800) CB203 (220900) CB204 (22000) CB205 (2200) CB206 (22200) CB207 (22300) CB208 (22400) CB08 (220300) CB209 (22500) CB20 (22600) CB2 (22700) CB22 (22800) CB205HP (7590) CB206HP (75565) CB207HP (7556) CB208HP (75566) CB08HP (75567PT) CB209HP (75562) CB20HP (75568) CB2HP (76249) CB22HP (75569PT) CT205 (24600) CT206 (24700) CT207 (24800) CT208 (24900) CT08 (2400) CT209 (242000) CT20 (24200) CT2 (242200) CT22 (242300) TW20 (3400PT) TW202 (3500) TW203 (3600) TW204 (3700) TW205 (3800) TW206 (3900) TW207 (32000) TW208 (3200) TW08 (3300) TW209 (32200) TW20 (32300PT) TW2 (32400) TW22 (32500) 99B (02042) 995B (02045) 200B (020460) 2005B (020450) 20B (020500) 202B (020600) 203B (020700PT) 204B (020800) 205B (020900) 206B (02000) 207B (0220) 208B (02400) 08B (02500) 209B (02600) 20B (0280) 2B (02200) 22B (02200) 88 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
6 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Drills and Brushes (continued) Tube I.D. Diameter of AT CB CB (Carbide) CT Drill or Brush Stud (Standard) Drills (Carbide) Drills HP Drills* (Carbide Twist) TW Wire Thread Drills (Twist) Drills Brush in. mm in. mm Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF /6" UNF /6" UNF /6" UNF /6" UNF /6" UNF /6" UNF /6" UNF AT23 (93800) AT24 (93900) AT25 (94000) AT26 (9400) AT27 (94200) AT28 (94300) AT29 (94400) AT220 (94500) AT22 (94600) AT222 (94700) AT223 (94800) AT224 (94900) AT225 (95000) AT226 (9500) AT227 (95200) AT228 (95300) AT229 (95400) * HP Style drills are used for more aggressive cleaning with CC325HP cleaning motor CB23 (22900) CB24 (222000) CB25 (22200) CB26 (222200) CB27 (222300) CB28 (222400) CB29 (222500) CB220 (222600) CB22 (222700) CB222 (222800) CB223 (223000PT) CB224 (223000PT) CB225 (22300) CB226 (223200) CB227 (223300) CB228 (223400) CB229 (223500) CB23HP (75570PT) CB24HP (7557) CB25HP (75859) CB26HP (75572) CB27HP (75573) CB28HP (75950) CB29HP (75730PT) CB220HP (7642PT) CB22HP (76434) CB222HP (76223) CT23 (242400) CT24 (242500) CT25 (242600) CT26 (242700) CT27 (242800PT) CT28 (242900) CT29 (243000) CT220 (24300) CT22 (243200PT) CT222 (243300PT) CT223 (243400) CT224 (243500) CT225 (243600) CT226 (243700) CT227 (243800) CT228 (243900) CT229 (244000) TW23 (32600) TW24 (32700) TW25 (32800) TW26 (32900) TW27 (33000) TW28 (3300) TW29 (33200) TW220 (33300) TW22 (33400) TW222 (33500) TW223 (33600) TW224 (33700) TW225 (33800) TW226 (33900) TW227 (34000) TW228 (3400) TW229 (34200) 23B (022500) 24B (022700) 25B (022802) 26B (022900) 27B (023000) 28B (02300) 29B (023200) 220B (023304) 22B (023400) 222B (023600) 223B (023700) 224B (023800) 225B (023900) 226B (02400PT) 227B (02400) 228B (024200) 229B (024300) Large Diameter Twist Brushes (LDTB) Brush should be sized /8" 3/6" smaller than the nominal tube I.D. for best results. in. Diameter mm Model Order Stud Thread LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB PT 5/8 NC LDTB /8 NC LDTB PT 5/8 NC LDTB PT 5/8 NC in. Diameter mm Model Order Stud Thread LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 89
7 Condenser Cleaners Tube Cleaners Tube cleaners for condensers, chillers, evaporators and other tubular heat transfer apparatus Model ABM800 Variable speed feature allows the operator to operate the shaft at a safe, comfortable speed for the condition of the tubes being cleaned. The lack of orings and coupler nut eliminates the risk of the coupler nut loosening and leaking water, leading to possible shaft damage. Variable solid state speed control from 0 to 750 RPM with constant torque Quickrelease shaft coupling for an easy, fast, positive connection every time No orings or coupler nut Model ABM900 Variable solid state speed control from 0 to 750 RPM with constant torque Manifold for screwon style shafting that is commonly used in competitive models Reversible Models ABM800R & ABM900R Same features as ABM800 & ABM900 above plus Bidirectional shaft rotation for the cleaning of internally enhanced tubes Identified Forward and Reverse direction foot pedals are included abm900 abm800r Model Ordering Horsepower Volts Amps RPM Bidirectional Operation Dimensions Weight (less shaft) Shipping Dimensions Shipping Weight (less shaft) ABM / No W 7" L 9" H 35 lbs. 2" W 23" L H 39 lbs. ABM800R / Yes W 7" L 9" H 4 lbs. 2" W 23" L H 45 lbs. ABM / No W 7" L 9" H 35 lbs. 2" W 23" L H 39 lbs. ABM900R / Yes W 7" L 9" H 4 lbs. 2" W 23" L H 45 lbs. ABM900R230V* / Yes W 7" L 9" H 4 lbs. 2" W 23" L H 45 lbs. *CE Certified Fleible shafts (sold separately) To order the correct size Fleible, measure the tube I.D. and the length of the tube to be cleaned. Then refer to the chart at the right to select the proper shaft. Tube I.D. Range O.D. Lengths in Feet Model No. (Ordering No.) Fleible s for ABM800, ABM800R and ABM ".406 FS85/4 ( ).407".532" FS8253/8 ( ) FS8353/8 ( ).533".82" /2" FS825/2 ( ) FS835/2 ( ) Fleible s for ABM900 and ABM900R.280".406 FS95/4 ( ).407".532" FS9253/8 ( ) FS9353/8 ( ).533".82" /2" FS925/2 (290040) FS935/2 (29004) See net page for brush selection. Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 90
8 Condenser Cleaners BrushMaster Tube Cleaners SCB750 Brushmaster Brushes Super 2D Brushes Airetool Super 2D Brushes are for cleaning internally enhanced tubing. The brush is constructed from material that out cleans and out wears other tube brushes. Super 2 D Brushes have two cleaning diameters to assure all surfaces are being cleaned. These brushes are recommended for removing soft and light scale deposits. SB000 Super Brushes Super Brushes are for cleaning smooth bore tubing. They are made from the same longlasting material as the Super 2D Brush. The longer brush cleaning surface reduces the tube cleaning time. They are recommended for removing soft and light scale deposits. N625 Part Order in. Tube Inside Diameter mm B625 Super 2 D Brush SCB SCB Super Brush SB SB SB Nylon, Brass and Stainless Steel Brushes Nylon, brass and stainless steel brushes are available in brush diameters.250".000" ( mm) in /6" (.6mm) increments. Select the brush size equal to or one size smaller than the I.D. of the tubes to be cleaned. Minimum order quantity 2 pieces Brush Diameter Brush Material in. mm Nylon Brass Stainless Steel / N250 ( ) B250 (299655) SS250 (299654) 5/ N32 ( ) B32 (299656) SS32 ( ) 3/ N375 ( ) B375 (299657) SS375 ( ) 7/6.0 N437 (299653) B437 (299658) SS437 ( ) / N500 ( ) B500 (299659) SS500 ( ) 9/ N562 ( ) B562 ( ) SS562 ( ) 5/ N625 ( ) B625 (299652) SS625 ( ) / N687 ( ) B687 ( ) SS687 ( ) 3/ N750 ( ) B750 ( ) SS ) 3/ N82 ( ) B82 ( ) SS82 ( ) 7/ N875 ( ) B875 ( ) SS875 (299655) 5/ N937 ( ) B937 ( ) SS937 ( ) N000 ( ) B000 ( ) SS000 ( ) Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 9
9 Boiler Tube Cleaners Tube Cleaners for Straight Tubes Complete series of motors and heads available for tube sizes /2" to (2.7 to 34.9 mm) I.D. Drill with Universal Joint Range: /2 in. (2.7 mm) 3/8 in. (34.9 mm) Deposit: heavymedium to soft Midget Motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; metal bo; choice of single unit cutter head with four etra cutters and two etra cutter pins. If a Type 2 head (30 series) is ordered, one etra fleible connection is furnished. If epanding blade head is ordered, one etra set of blades is furnished. For operating hose (not included) refer to page 6. Single Unit with Universal Joint Range: /2 in. (2.7 mm) 3/8 in. (34.9 mm) Deposit: lighthard to medium Epanding Blade Cutter Range: /2 in. (2.7 mm) 4/2 in. (4.3 mm) Deposit: lighthard to medium Complete series of motors and heads available for tube sizes /2" to 3 (2.7 to 336.5mm) I.D. Type4 Forward Swing Range: 3/4 in. (44.4 mm) 4 /4 in. (20.6 mm) Self feeding Deposit: /2 in. (2.7 mm) thicksoft to medium Type5 Wing Arm Range: 3/4 in. (44.4 mm) 3 /4 in. (336.5 mm) Self feeding Deposit: /2 in. (2.7 mm) thickhard to medium 3000 Series Motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; choice of cutter head with two etra sets of cutters and cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra sets of cutters are furnished. If armtype head is ordered, one etra set of arm pins is furnished. For operating hose (not included) refer to page 6. Type3 PType Range: 2/4 in. (57. mm) 7 in. (77.8 mm) Self feeding Deposit: 3/8 in. (9.5 mm) thickhard to medium Drill with Universal Joint Range: /2 in. (38. mm) in. (279.4 mm) Deposit: 3/4 in. (9.0 mm) thickmedium to hard and plugged tubes Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 92
10 Boiler Tube Cleaners Tube Cleaners for Curved Tubes Complete series of motors and heads available for tube sizes 3/6" to 2/8" (20.6 to 53.9 mm) I.D. Drill with Universal Joint Range: /2 in. (38. mm) 2/8 in. (53.9 mm) Deposit: lighthard to medium midget motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; metal bo; choice of single unit cutter head with four etra cutters and two etra cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra cutters are furnished. For operating hose (not included) refer to page 6. Type 40" Series Single Unit with Universal Joint Range: /2 in. (2.7 mm) 2/8 in. (53.9 mm) Deposit: lightmedium to hard Type2 30" Series Single Unit with Fleible Range: /2 in. (2.7 mm) 2/8 in. (53.9 mm) Deposit: lightmedium to hard Complete series of motors and heads available for tube sizes /2" to 3 (38. to mm) I.D. Drill with Universal Joint Range: /2 in. (38. mm) in. (279.4 mm) Deposit: /2 in. (2.7 mm) thickhard to medium 4000 series motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; choice of cutter head with two etra sets of cutters and cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra sets of cutters are furnished. If armtype head is ordered, one etra set of arm pins is furnished. For operating hose (not included) refer to page 6. Type4 Forward Swing with Universal Joint Range: 3/4 in. (44.4 mm) 43/4 in. (20.6 mm) Deposit: /2 in. (2.7 mm) thicksoft to medium Type5 Wing Arm with Universal Joint Range: 3/4 in. (44.4 mm) 3/4 in. (336.5 mm) Self feeding Deposit: /2 in. (2.7 mm) thickhard to medium Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 93
11 Boiler Tube Cleaners Selection Guide Midget Tube Cleaners Curved and Straight Range: /2 to 3/4 in. 2.7 to 44.4 mm Complete cleaner consists of: air motor with etra set of blades; shaft wrench; metal bo; choice of single unit cutter head with four etra cutters and two etra cutter pins. If a Type 2 head (30 series) is ordered, one etra fleible connection is furnished. If epanding blade head is ordered, one etra set of blades is furnished. For operating hose (not included) refer to page 6. midget motor Tube I.D. Minimum Tube Centerline Radius Motor Motor O.D. Rotor Air Thread Hose Size Pipe Tap in. mm in. mm in. mm in. (in.) in. mm Universal Type s Available Fleible Type 2 Blade Type 8 Use for straight tubes. Use for curved tubes. Drill* Universal Fleible /2 2.7 Straight 24 5/ / MD /8 5.8 Straight 30 37/ /4 NF /8 / MD2 PA305 X646 3/4 9.0 Straight 27 /6 7.4 /4 NF /8 / MD3 PA305 X646 3/ X64 /6 7.4 /4 NF /4 /4 6.3 X6440 X6430 MD3 645 X646 7/ Straight 29 25/ /8 NF /4 3/ MD4 265A 27/ Straight 29 25/ /8 NF /4 3/ MD4 265A 25.4 Straight 26 29/ /8 NF 3/8 3/ MD4 265A / X6 7/ /6 NF /4 /4 6.3 X640 X630 MD3 65C X66 / Straight 3 / /6 NF 3/8 3/ MD5 35 X636 /4 3.7 Straight X63A / /8 NF 3/8 3/8 9.5 X6340 X MD5 665 X636 / X63 / /8 NF 3/8 3/8 9.5 X6340 X6330 MD5 665 X636 3/ Straight X65A 3/ /8 NF 3/8 3/8 9.5 X6540 X X666 / X65 3/ /8 NF 3/8 3/8 9.5 X6540 X6530 MD5 665 X666 5/ / /8 NC /2 / / X66 5/ /8 NF 3/8 3/8 9.5 X6640 X X666 3/ / /8 NC /2 / Some items are available on a quotation basis only. * Drill must be used with Universal Joint or fleible connection. 94 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
12 Boiler Tube Cleaners Selection Guide 3000 and 4000 Series Tube Cleaners Curved and Straight Range: /2 to 3/4 in. 38. to mm Complete cleaner consists of: air motor with etra set of blades; shaft wrench; choice of cutter head with two etra sets of cutters and cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra sets of cutters are furnished. If armtype head is ordered, an etra set of arm pins is furnished. For operating hose (not included) refer to page 6. Use for straight tubes. Use for curved tubes. Tube I.D. Minimum Tube Centerline Radius Motor Motor O.D. Rotor Air s Available Thread Hose Size Single Forward Single Unit Pipe Tap Epansion Swing in. mm in. mm in. mm in. (in.) in. mm Type 3 Type 4 Type 2 Type Universal Joint Drill* /2 38. Straight 350 3/ /6 NC /2 /2 2.7 TC /8 4.2 Straight 362 / /8 NC 3/4 /2 2.7 TC / Straight 375 5/ /8 NC 3/4 /2 2.7 TC / Straight 387 3/ /8 NC 3/4 3/4 9.0 TC7PY Straight / /8 NC 3/4 3/4 9.0 TC / /8 NC /2 / / Straight /8 NC 3/4 3/4 9.0 TC3PY / / /8 NC /2 / /4 57. Straight / /4 NC 3/4 3/4 9.0 P5PY 4470A / / /8 NC /2 / / / /8 NC /2 / / Straight / /4 NC 25.4 P9S 4470A / Straight / /8 NC 25.4 P9 4470B / / /8 NC /2 / Some items are available on a quotation basis only. * Drill must be used with Universal Joint or fleible connection. Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 95
13 Boiler Tube Cleaners Selection Guide Tube I.D. Minimum Tube Centerline Radius Motor Motor O.D. Rotor Air Thread Hose Size Pipe Tap in. mm in. mm in. mm in. (in.) in. mm Single Epansion Type 3 s Available Wing Arm Type 5 25/ Straight / /8 NC 25.4 P A / / /4 NC 3/ / Straight / /8 NC 25.4 P A / / /4 NC 3/ / Straight / /8 NC 25.4 P6A / / /4 NC 3/ Straight /6 7.4 NF 25.4 P / /4 NC 3/ / /4 NC 3/ / Straight /6 7.4 NF 25.4 P / Straight / NF 25.4 P / Straight NF 25.4 P / Straight NF 25.4 P / / /8 NC B / Straight NF 25.4 P Straight /6 84. /8 NF 25.4 P / / /8 NC B / Straight /6 84. /8 NF 25.4 P / Straight /6 84. /8 NF 25.4 P / Straight /6 84. /8 NF 25.4 P Straight / /8 NF 25.4 P / /8 NC B / Straight / /8 NF 25.4 P / Straight / /8 NF 25.4 P 5060AS / / /8 NC B /8. Straight / /8 NF 25.4 P 5060AS /2 4.3 Straight / /8 NF 25.4 P0 5060AS / / /8 NC B / / /8 NC B / Straight / /8 NF 25.4 P0 5060AS / / /8 NF A Straight / /8 NF /4 /4 3.8 TC9HS E / /8 NF /4 3.8 TC9HS Some items are available on a quotation basis only. * Drill must be used with Universal Joint or fleible connection. Forward Swing Type 4 Universal Joint Drill* 96 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
14 3000 Series Motors 3000 Series Motors 3000 series straight motors, components and (ordering numbers) All Motors include Wrench Motor Motor O.D. Tube I.D. Case Cylinder Rear Machine Rotor Blades (Qty.) Thrust Plate Front Bearing Rear Bearing Rear Cap Front Dowel Rear Dowel Wrench Rotor Hose Thread Size 350 ( ) 362 ( ) 375 ( ) 387 (407600) 3200 (407600) 322 ( ) 3225 ( ) 3250 ( ) 3262 ( ) 3275 ( ) /2" /2" 2" 2" 2/8" 2/8" 2 2 2/2" 2/2" ( ) 23/6" 3" 338 ( ) 3350 ( ) 3400 ( ) 3500 ( ) 3600 ( ) 3" 33/6" " 4 5" 5 6" 350 (38900) 362 (39900) 375 (40600) 387 (40900) 3200 (4400PT) 322 (42200) 3225 (43000) 3250 (44600) 3262 (45600) 3275 (4600) 3300 (46900) 338 (4800) 3350 (49200) 3400 (50800) 3500 (5300) 3600 (5600) 3502 (39000) 3622 (40000) 3622 (40000) 3872 (4000) (4500) 3222 (42400) (43200) (44800) (45800) (46300) (47000) (48600) 3503 (3900) 3623 (4000) 3623 (4000) 3873 (400) (4600) 3223 (42500) (43300) (44900) (45900) (46400) (4700) (48700) (49500PT)(49600PT) (500) (55300) (55300) (5200) (55400) (55400) 3504 (39200) 3624 (40200) 3624 (40200) 3874 (4200) (4700) 3224 (42600) (43400) (45000) (46000) (46500) (47200) (48800) (49700) (5300) (55500) (55500) 3505 (39300) 3625 (40300) 3625 (40300) 3875 (4300PT) (4800) 3225 (42700) (43700) (4500) (46600) (46600) (47400) (49000) (49900) (5600) (55800) (55800) 806 (4) (04900PT) 806 (4) (04900PT) 806 (4) (04900PT) 2306 (4) (053700) 2306 (4) (053700) 2606 (4) (35800) 2506 (5) (34300) 2406 (5) (33000) 2306 (5) (3700) 2306 (5) (3700) 2006 (5) (2500) (5) (6200) (5) (6200) (5) (6200) 2206 (5) (25300) 2206 (5) (25300) 707 (047500) 807 (049200) 807 (049200) C (38800) 2307 (053800) 2607 (35900) 507 (045800) 2407 (3300) 2907 (37700) 2307 (3800) 2007 (2600) (9300) (6300) (5800) (55900) (55900) Motors for tube/pipe sizes larger than 5" ID are supplied with ribs or rib cage to center the motor in tube or pipe being cleaned. X 708 (330400) X 808 (330500PT) X 808 (330500PT) 2208 (05300) 2208 (05300) 2208 (05300) 408 (045500) 2408 (33200) 008 (040700) 008 (040700) 08 (043400) 08 (043400) (6400) (6400) 2208 (25400) 2208 (25400) 3509 (39400) 3629 (40500) 3629 (40500) 3229 (42900) (4900) 3229 (42900) (4900) (4900) (46700) (46700) (47500) (47500) (47500) (47500) (47500) (47500) 323 (07300) 443 (08500) 323 (07300) 323 (07300) 23 (022300PT) 23 (022300PT) 73 (030700) 73 (030700) 73 (030700) 73 (030700) 73 (030700) 73 (030700) 35 (39500) 35 (39500) 35 (39500) 38 (40700) 38 (40700) 320 (42000) 320 (42000) 325 (45200) 326 (45400) 326 (45400) 326 (45400) 332 (48200) 332 (48200) 332 (48200) 332 (48200) 332 (48200) 352 (39600) 352 (39600) 352 (39600) 382 (40800) 3202 (7598) 322 (4200) 322 (4200) 3252 (45300) 3262 (45500) 3262 (45500) 3262 (45500) 3322 (48300) 3322 (48300) 3322 (48300) 3322 (48300) 3322 (48300) 9/6" (40809) (4080) (4080) (4080) (4080) (4080) (4082) (4084) (4084) (4084) (324600) (324600) 9/6" /8" /8" (324800) /8" /8" (324800) (324900) (324900) /2" /2" /2" Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 97
15 4000 Series Motors 4000 Series Motors 4000 series motors, components and (ordering numbers) Motor 4250 ( ) 4300 ( ) 4325 ( ) 4350 ( ) 4450 (40800) 448 (408400) 4600 (408800) Motor O.D. Tube I.D. Case Cylinder Rear Machine Rotor Blades (Qty.) Thrust Plate 2/4 X 5R 25/6 X 2R (4) /2 X 5R (62700) (62900) (63000) (6300) (63700) (08300) (053800) 2 25/8 X 24R (5) /4 X 2R (64400) (64800) (64900) (65000) (65500) (072600) (072700) 2/2" 2 27/8 X 28R 3 X 6R 3/4 X 6R 3/2 X 20R 3/8" 4 X 5R (5) 3207 (66800) (67000) (6700) (67200) (67900) (0700) (07200) (5) 3307 (6800) (68200) (68300) (68400) (68800) (077900) (078000) Front Bearing 4408 (08400) 3308 (072800) 3308 (072800) 3708 (07800) Rear Bearing (63800) (4900) (4900) (5) (69800) (70200) (70300) (70400) (70600) (082900) (026400) (083000PT) (47500) 3 43/6 X 8R (5) (70800) (70900) (5200) (5300) (700) (083700) (5800) 5" 53/4 X 72R 6 X 26R *Includes Machine Motors are supplied with ribs or rib cage for tube/pipe sizes larger than 6" ID (5) (7900) (70900) (5200) (5300) (700) (083700) (5800) 5008 (083800) 5008 (083800) Rear Cap 443 (08500) 323 (07300) 323 (07300) Front Dowel Rear Dowel (42000) (63900) (65700) (65800) (66600) (66700) (46700) (022300PT) (43900) (68900) (47500) (47500) 73 (030700) 73 (030700) 73 (030700) (48300) (70700) (48300) (70700) (48300) (70700) Tail Hose Assembly* Line A Below Line B Below Line B Below Line B Below Line B Below Not Req d Not Req d Wrench (4080) (4082) (4082) (4084) (4084) Rotor Thread /8" (324800) /8" /8" (324800) /8" Hose Size /2" Line Tap Size A /2" B Tail Hose 445 (08600) 335 (072900) Hose 46 (079000) 336 (07300PT) Clip Screw Ferrule ) 338 (800065) 448 (08700) Accessory Heavy Duty Screw Type Tail Hose Assemblies with Wire Inserted Hose and Spring Protector for 4000 Series Motors Tail Hose Assembly HD (409200) HD ( ) HD ( ) HD ( ) HD ( ) HD (409250) Used With Motor Assembly Machine Hose Hose Pipe Tap Compression Nut Compression Ferrule Compression Sleeve Detail # Qty. Required KB (76866) B (65000) KB (67800) B (68500) B (70500) B (7950) (86900) (87300) (87300) (87600PT) (87600PT) (8800) /2" C (63300) C (67400) C (67400) C (68600) C (68600) C (7960) D (63400) D (67500) D (67500) D (67500) D (67500) D (7970) E (63500) E (67600) E (67600) E (67600) E (67600) E (7980) Hose (86800) K (87250) K (87250) K (87250) K (87250) K (88020) Spring (86950) K (67700) K (67700) K (67700) K (67700) K (7747) 98
16 60 Series & 4000 Series Motors 60 & 4000 Series Motors 60 & 4000 series motors, components and (ordering numbers) Motor Motor O.D. Tube I.D. (Radius) Case Rear w/ Bearing Machine Rotor Blades (4 req.) Rear Bearing Rear Dowel (Qty.) Tail Hose Tail Hose Tail hose Assembly Front Ferrule Rear Ferrule Wrench Rotor Thread Hose Size X 64 ( ) /6" X 6 ( ) X 63 ( ) /6" X 65 ( ) 3/6" X 66 ( ) 4200 ( ) 4225 (408000) /2" 3/6" (5") /32" (5") (6") /2" (6") (6") (24") (5") 2" (5") X 640 (334800) X 60 (33200) X 630 (333300) X 650 (336300PT) X 660 (337300) 4200 G (6300) 4225 G (62500) X 6403 (334900) X 603 (33300) X 6303 (333400) X 6503 (336400) X 6603 (337400) (6500) (6500) X 6404 (335000) X 604 (33400) X 6304 (333500) X 6504 (336500) X 6604 (337500) (6600) (6600) X 6405 (335200) X 605 (33600) X 6305 (333700) X 6505 (336700) X 6605 (337700) (6800) (6800) X 6406 (335300) X 606 (33700) X 6306 (333800) X 6506 (336800) X 6606 (337800) 406 (078800) 406 (078800) (6200) (6200) X 642 (2) (335400) X 62 (2) (33800) X 632 (2) (334000) X 632 (2) (334000) X 632 (2) (334000) 4202 (62200) 4202 (62200) X 645 (335500) X 65 (33900) X 635 (33400) X 635 (33400) X 635 (33400) 45 (078900) 45 (078900) X 646 (335600) X 66 (332000) X 636 (334200) X 636 (334200) X 636 (334200) 46 (079000) 46 (079000) X 649 X 647 (335700) X 69 X 67 (33200PT) X 639 X 637 (334300) X 659 X 637 (334300) X 669 X 667 (337900) 4209 (409500) 4209 (409500) AJ243 (7670) AJ243 (7670) X 648 (335800) X 68 (332200) X 638 (334400) X 638 (334400) X 638 (334400) AJ243 (7670) AJ243 (7670) 3/6" ( ) (40804) (40805) (40805) ( ) (4080) (4080) /2" /2" Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 99
17 Midget Motors Midget Motors For /2" I.D. tubes Straight tube midget motors, components and (ordering numbers) Motor Motor O.D. Tube I.D. Case Rear Machine Rotor Rotor Blade (Qty.) Dowel pin (Qty.) Wrench Rotor Thread Air Hose 24 ( ) 5/32" /2" X 240 (056400) 2403 (056500) 2404 (056600) 2405 (056700) 2406 (4) (056800) 242 (056900) 5/32" (324000) 032 3/6" 30 ( ) 37/64" X 300 (06700) X 3003 (067300) X 3004 (067400) X 2705 (063000) 2706 (4) (06300) 302 (067500) 3/6" ( ) 27 (407500) /6" X 270 (062600) X 2703 (062800) 2704 (062900PT) X 2705 (063000) 2706 (4) (06300) 302 (067500) 3/6" ( ) 29 A (407530) 25/32" 290 A (06490) 2903 A (06500) 2904 (06500) 2605 (060800PT) 2606 (4) (060900) X 62 (33800) (40805) 26 ( ) 29/32" 260 G (060500) 2603 (060600) 2604 (060700) 2605 (060800PT) 2606 (4) (060900) X 632 (334000) (40805) 3 ( ) /32" /8" 30 (069800) 303 (069900) 304 (070000) 305 (07000) 306 (4) (070200PT) 3 (070300) ( ) X 63 A (409000) /6" X 630 (333300) X 6303 (333400) X 6304 A (333600) X 6305 (333700) X 6306 (4) (333800) X 632 (2) (334000) (40805) X 65 A ( ) 3/6" X 650 (336300PT) X 6503 (336400) X 6504 A (336600) X 6505 (336700) X 6506 (4) (336800) X 632 (2) (334000) (40805) Water Driven Motors For 2" and 3 I.D. tubes Water driven motors are used only in the overhead cleaning of vertical catalyst tubes. Model Motor O.D. Tube I.D. Case Water Wheel Rear Machine Pipe Tap Thrust Bearing Front Bearing Rear Thrust Wrench Thread Hose W7 ( ) 3/2" 3 W 70 (39300) W 702 (39400PT) W 703 (39500) W 0704 (326000) /2" W 905 (39900) W 907 (320000) W 908 (32000) W 90 (320200) (4084) /2" W6A ( ) /6" 2" W 60 A (323300) W 602 (323400) W 603 A (323600) W 604 A (323800) W 605 (323900) W 607 (324000) W 608 (32400) W 60 (324200) (4080) * Other sizes available. Contact customer service for details Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 00
18 Gas Line Cleaners Gas Line Cleaners Range: 3/4 to /2 in to 38.0 mm Used successfully by gas utilities for cleaning old service lines before inserting new plastic and copper tubing. The thorough cleaning action of the barrelshaped cutter head assures the removal of material that could cut or rupture the renewal tubing. Renews gas service lines instead of replacing them Complete kit consists of: motor, with an etra set of blades; head; lubricator; wire wound hose; spare cutters and a metal carrying case Other sizes available on request Cleaner Complete Order Pipe I.D. Motor Assembly Motor Diameter Assembly Air Inlet Hose Size Hose Length in. mm Model Order No. in. mm Model Order No. in. mm in. mm ft M 27 GLC / / S / / X 64 GLC X / S / / X 6 GLC 50 / X / S / / X 63 A GLC /4 3.7 X 63 A / S / / X 63 A GLC /4 3.7 X 63 A / S / / X 65 GLC /2 38. X / S / / X 65 A GLC /2 38. X 65 A / S 3/ / X 65 A GLC /2 38. X 65 A / S 3/ / * Other sizes may be available. Contact customer service for details Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 0
19 Type Single Unit s /2" 2 I.D. Series 40 Single unit heads, components and (ordering numbers) Tube I.D. Universal Joint Jaw Tap Adapter Cutter Pin Cone Cutter Cylinder Cutter 2440 (405800) /2" 245 ( ) (057000) 2487 S (058400) 3040 ( ) /6" PA 305 ( ) 2734 (063300) 3037 ( ( ) 3/6" PA 305 ( ) 2734 (063300) C 3 (22500) 2740 S (404802PT) 3/6" 645 ( ) 2944 (065900) 2947 S (2) (06600PT) X 6440 ( ) 3/6" 645 ( ) 2944 (065900) 2947 (066000) 2940 ( ) 27/32" 265 ( ) 2943 (065800) 2944 (065900) 2947 (066000) 2640 (405200) 265 ( ) 2643 (06200) 2644 (06400) 337 (025700) X 640 ( PT) /32" 65 (409600PT) 2644 (06400) 337 (025700) 340 ( ) /8" 665 ( ) 7/6" 344 A (070500) 2837 (064600) X 6340 ( ) 665 ( ) 2544 S (059400) 947 (038700) 2240 ( ) /2" 35 ( ) 7/6" 2544 S (059400) 947 (038700) X 6540 ( ) 665 ( ) 2544 S (059400) 6547 (097600) 740 ( ) /2" 355 ( ) 9/6" 743 (04780) 2844 (064800) 097 (04300) 088 (042800) 940 (405000) 45 ( ) 943 (05400) 944 (05500) 797 (034500) 788 (034300) X 6640 ( ) 665 ( ) 2544 S 897 B (059400) (038300) 440 ( ) 2" 45 ( ) 943 (05400) 944 (05500) 897 B (038300) 888 B (037700) 4440 C ( ) 2 45 ( ) 943 (05400) 944 (05500) 897 (03800) 888 (037600) Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 02
20 Type 2 Single Unit s /2" 2/8" I.D. Series 30 Single unit heads, components and (ordering numbers) Tube I.D. Fle Connection Cpl. Tap Cpl. Tap Adapter Cutter Pin Cone Cutter Cylinder Cutter Length Diameter 2430 (405700) /2" 246 A ( ) (057000) 2487 S (058400) 4" 3/6" 3030 (405300) X 646 A ( ) 2734 (063300) 3037 (06800) 4" 3/6" 2730 ( ) X 646 A ( ) 2734 (063300) C 3 (22500) 4" 3/6" X 6430 ( ) 3/6" X 646 A ( ) 2944 (065900) 2947 (066000) 4" 3/6" 2930 ( ) 296 A ( ) 2943 (065800) 2944 (065900) 2947 (066000) 4/2" A ( ) 2644 (06400) 337 (025700) 4/2" 2630 ( ) 266 A ( ) 2644 (06400) 337 (025700) 4/2" X 630 ( ) /32" X 66 A ( ) 2644 (06400) 337 (025700) 4" ( ) /8" X 636 A ( ) 7/6" 344 A (070500) 2837 (064600) 4/2" X 6330 (407400) X 636 A ( ) 7/6" 2544 S (059400) 947 (038700) 4/2" X 6530 ( ) /2" X 666 A ( ) 7/6" 2544 S (059400) 6547 (097600) 6/2" X 6630 ( ) X 666 A ( ) 7/6" 2544 S (059400) 797 (034500) 6/2" 430 ( ) 2/8" 46 A (403700) 943 (05400) 944 (05500) 897 B (038300) 888 B (037700) 7" /2" Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 03
21 Type 3 Single Epansion P & TC s /2" 7" I.D. for Straight Tubes and Drill Pipe Single epansion heads, components and (order numbers) PY heads developed specifically for the rigorous conditions found in Pipe Yard applications PY heads have larger diameter front ends and stronger coupling studs that increase durability Tube I.D. Closed Epands To Cage Pin Plate Tap Cutter Pin Cone Cutter Cylinder Cutter TC 4 ( ) TC (407500) TC 7 PY (405583) TC 6 PY (405566) TC 3 PY (405569) P 5 PY (405570) P 9 S ( ) P 9 PY (405567) P 8 ( ) P 7 ( ) P 6 A PY (40559) P 6 P 5 ( ) P 4 ( PT) P 3 ( ) P 2 ( ) P P 0 P 0 ( ) TC 9 H S TC 9 S TC 20 S ( ) TC 2 S TC 22 S TC 23 S TC 24 S /2" 23/32" 2" /6" 2" 2" 3/6" 23/6" 2/8" 2 2 2/6" 27/6" 2 23/6" 2/6" 2/2" 2 23/6" 2 29/6" /6" 2 3" 2/6" 3/8" 3/8" 23/6" 3 3 3/6" 39/6" 3/2" 33/6" 33/6" 3 39/6" 43/6" 4" 3 4/2" 4 33/6" 4 4/2" 4/8" " 4/2" 59/6" " 5/2" 6/2" /2" 6" 7/6" " 6/2" 79/6" 78 (048300) 88 (050700) 228 T C 7 PY (7708) 238 PY (76988) 238 A PY (76995) P 59 PY (76997) P 99 S (292700) P 99 PY (76990) P 89 (29800) P 592 (294400) P 992 S (293400) P 992 (293300) P 892 (292300) 783 (048500) 883 (05000) 2383 (055400) 2383 (055400) 2383 (055400) 83 (09900) 83 (09900) 83 (09900) 2483 (33700) P 79 P S (039800) P 69 A PY (77032) P 692 A (290700) P 69 AY P 692 (290600) P 59 (28900) P 49 (288500PT) P 39 (287900) P 29 (28700) P 592 (289600) P 492 (289000) P 392 (288300) P 292 (287700) 983 S (039800) 983 S (039800) 983 S (039800) 883 D (03600) 883 F (036400) 883 F (036400) P 9 P F (036400) P 09 (286300) P 09 (293500) 99 H S 99 S 209 S (052800) 29 S 229 S 239 S 249 S P 092 (286600) P 092 (293800) 883 F (036400) 883 F (036400) (00) 8293 (00) 8293 (00) 8293 (00) 8293 (00) 8293 (00) 9/6" /8" /8" /8" 584 (), 884 () (046600) (0500PT) 584 (), 884 () (046600) (0500PT) 584 PY (3) (76989) 584 PY (3) (76989) 584 PY (3) (76989) 2484 PY (3) (76998) 2484 (3) (057900) 584 PY (3) (76989) 84 (3) (020300) 84 (3) (020300) 84 PY (3) (77033) 84 (3) (020300) 84 (3) (020300) 884 (3) (036700) 884 (3) (036700) 884 (3) (036700) 884 P (3) (036800) 884 P (3) (036800) 884 P (3) (036800) 884 P (3) (036800) 884 P (4) (036800) 884 P (4) (036800) 884 P (4) (036800) 884 P (4) (036800) 2484 S (4) (05800) 2484 S (4) (05800) 787 () (048600) 587 () (046700) 2287 (3) (053400) 787 (3) (048600) 787 (3) (048600) 2487 (3) (058200) C 52 (3) (27500PT) 587 (3) (046700) 087 (3) (042700) 087 (3) (042700) 087 (3) (042700) 087 (3) (042700) 987 (3) (040000) 787 (3) (034200) 887 B (3) (037300) 887 (3) (03700) 887 (3) (03700) 887 B (3) (037300) 887 (3) (03700) 287 (3) (044300) 287 (4) (044300) 287 (4) (044300) 788 (2) (048800) 588 (2) (047000) 2288 (6) (053500) 788 (6) (048800) 788 (6) (048800) 2488 (6) (77384) C 76 (6) (28400) 588 (6) (047000) 088 (6) (042800) 088 (6) (042800) 088 (6) (042800) 088 (6) (042800) 988 (6) (04000PT) 788 (6) (034300) 888 B (6) (037700) 888 (6) (037600) 888 (6) (037600) 888 B (6) (037700) 888 (6) (037600) 288 (9) (044400) 288 (2) (044400) 288 (2) (044400) 887 (4) 888 (2) 887 (4) 888 (2) 8287 (4) 8288 (2) 8287 (4) 8288 (2) 04 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
22 Type 4 Forward Swing Arm s 4 I.D. for Straight Tubes, Bent Tubes and Drill Pipe Forward swing arm heads, components and (ordering numbers) Recommended spare parts: cone cutters and cutter pins, cutter arms and arm pins. Figure Shown with head coupling for straight tubes. Figure 2 Shown with universal coupling for bent tubes. Tube I.D. Closed Epands To Spider Figure Long Arm Short Arm Cpl. Cpl. Tap Long Cutter Pin Short Cutter Pin Arm Pin Pin Lock Cone Cutter Star Cutter No. of Arms 840 ( ) 840 B ( ) 2340 (405400) 4440 ( ) 4470 ( ) 4470 A ( ) 3370 ( ) 3370 A ( ) 3270 ( ) 3270 A 7/8 (405400) 970 ( ) 970 B ( ) 770 ( ) 770 B ( ) /2" 2/8" 2 /2" 2/8" 2" 3" 2" 3" 2 2" 3 2 2" " 2/2" 4" 3" 2/2" 4" /2" 3" 4 3/2" 3" ( ) 3/4 4" 3 5/8" 870 B ( ) 3/4 4" 3 5/8" 770 S A ( ) 770 S 4 2 5/2" 4 2 5/2" 84 (049800) 84 (049800) 234 (054000) 234 (054000) 447 (082200) 447 (082200) 337 (075500) 337 (075500) 327 (07700) 327 (07700) 97 (039000) 97 (039000) 77 (033000) 77 (033000) S (03300) 77 S (03300) () (049900) 842 () (049900) 842 A () (050000) 842 A () (050000) 832 () 832 A () (049400PT)(049500PT) MM 66 (279200) 832 () 832 A () MM 66 (049400PT)(049500PT) (279200) 4472 (3) (082300) 4472 (3) (082300) 3372 (3) (075600) 3372 (3) (075600) 3472 (2) (07600) 3472 (2) (07600) 972 (2) (03900) 972 (2) (03900) 772 (2) (033200) 772 (2) (033200) 772 (2) (033200) 772 (2) (033200) 772 S (4) (033400) 772 S (4) (033400) 3272 (2) (07800) 3272 (2) (07800) 972 A (2) (039200) 972 A (2) (039200) 772 A (2) (033300) 772 A (2) (033300) 772 A (2) (033300) 772 A (2) (033300) MM 66 (279200) 2383 B (055600) 355 ( ) /8 (052600) 355 ( ) /8 (052600) 543 7/8 (027300) 55 ( ) 873 A (035400) 5 ( ) 873 A 5 ( ) 543 7/8 (027300) 55 ( ) 834 () (049600) 834 () (049600) 834 () (049600) 834 () (049600) 4474 (3) (082400) 4474 (3) (082400) 3374 (3) (075700) 3374 (3) (075700) 3474 (2) (076200) 3474 (2) (076200) 974 (2) (039300) 974 (2) (039300) 774 (2) (033500PT) 774 (2) (033500PT) 774 (2) (033500PT) 774 (2) (033500PT) 774 S (4) (033700) 774 S (4) (033700) 834 A () (049700) 834 A () (049700) 834 A () (049700) 834 A () (049700) 3274 (2) (07900) 3274 (2) (07900) 974 A (2) (039400) 974 A (2) (039400) 774 A (2) (033600) 774 A (2) (033600) 774 A (2) (033600) 774 A (2) (033600) 845 (2) (05000PT) 845 (2) (05000PT) 2345 (2) (054300) 2345 (2) (054300) 4475 (3) (082500) 4475 (3) (082500) 3375 (3) (075800) 3375 (3) (075800) 3275 (2) (072000) 3275 (2) (072000) 975 (4) (039500) 975 (4) (039500) 775 (4) (033800) 775 (4) (033800) 846 (050202) 846 (050202) 2346 (054400) 2346 (054400) 4476 (082600) 4476 (082600) 3376 (075900) 3376 (075900) 3276 (072200) 3276 (072200) 976 (4) (039600) 976 (4) (039600) 776 (033900) 776 (033900) 337 (2) (025700) 337 (2) (025700) 337 (2) (025700) 337 (2) (025700) C 9 (3) (2400) C 9 (3) (2400) 637 (3) (028800) 637 (3) (028800) 047 (2) (04700) 047 (2) (04700) 637 (4) (028800) 637 (4) (028800) 747 (4) (03700) 747 (4) (03700) 875 (4) (4) (03700) 875 (4) (4) (03700) 775 (4) (033800) 775 (4) (033800) 776 S (4) (034000) 776 S (4) (034000) 747 (4) (03700) 747 (4) (03700) 338 (3) (025905) 338 (3) (025905) 338 (3) (025905) 338 (3) (025905) (2) (064600) 2837 (2) (064600) Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 05
23 Type 4 SRA Spring Retracting Arm s /2" 4 I.D. for Straight Tubes, Bent Tubes, and Drill Pipe Forward swing arm heads, components and (ordering numbers) Recommended spare parts: cone cutters and cutter pins, cutter arms and arm pins. Developed specifically for Drill Pipe applications to protect bo end threads The SRA arms are held closed until air is applied which allows for easy insertion into the bo end of drill pipe, especially when used with automated cleaning equipment SRA 470 9/6 (40569PT) SRA 870 5/8 (405684PT) SRA /4 (405679) SRA /8 (405678) SRA /8 (40568) SRA 3270 UJK (405694PT) SRA 970 7/8 (405680) SRA 770 7/8 (405677PT) SRA /8 (405683PT) Tube I.D. Closed Epands To /2" 2 2" 2 2 2" 3/2" " 2/2" 4" 3" 2/2" 4" /2" 3" 4 43/4' 2 5/2" Spider 47 (77450PT) 87 (050300PT) 447 (082200) 337 (075500) 327 (07700) 327 (07700) 97 (039000) 77 (033000) 77 (033000) Fig. 2 Long Arm 472 (3) (7745PT) 4472 (3) (082300) 4472 (3) (082300) 3372 (3) (075600) 3472 (2) (07600) 3472 (2) (07600) 972 (2) (03900) 772 (2) (033200) 772 S (4) (033400) Short Arm SRA 473 9/6 (77452PT) SRA 873 (77447PT) SRA /4 (77435) SRA /8 (77432) 3272 (2) SRA /8 (07800) (77432) 3272 (2) (07800) 972 A (2) (039200) 772 A (2) (033300) SRA 3273U (77456PT) SRA 973 7/8 (77442) SRA 773 7/8 (77429) SRA 773 7/8 (77429) Tap 9/6" Long Cutter Pin 474 (3) (77453PT) 4474 (3) (082400) 4474 (3) (082400) 3374 (3) (075700) 3474 (2) (076200) 3474 (2) (076200) 974 (2) (039300) 774 (2) (033500) 774 S (4) (033700) Short Cutter Pin 3274 (2) (07900) 3274 (2) (07900) 974 A (2) (039400) 774 A (2) (033600) Arm Pin Pin Lock Cone Cutter 475 (3) SRA (3) (77454PT) (77455PT) (066000) 4475 (3) (082500) 4475 (3) (082500) 3375 (3) (075800) 3275 (4) (072000) 3275 (4) (072000) 975 (4) (039500) 775 (4) (033800) 775 (4) (033800) SRA 876 C 9 (3) (77448PT) (2400) SRA 4476 (77434) SRA 3376 (7743) SRA 3276 (77444) SRA 3276 (77444) SRA 976 (7744) SRA 776 (77428) SRA 776 (77428) C 9 (3) (2400) 637 (3) (028800) 047 (2) (04700) 047 (2) (04700) 637 (4) (028800) 747 (4) (03700) 747 (4) (03700) Star Cutter 2837 (2) (064600) 2837 (2) (064600) Spring SRA 479 (77449PT) SRA 879 (77448PT) SRA 4479 (77436) SRA 3379 (7433) SRA 3379 (7433) SRA 3379 (7433) SRA 3379 (77433) SRA 779 (77430) SRA 779 (77430) Universal Joint 65 KNF (409450PT) No. of Arms Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
24 Type 5 Self Feed Clip Type Wing Arm s 8 I.D. for Straight Tubes and Pipe Wing arm heads, components and (ordering numbers) Tube I.D. Closed Epands To Spider Arm (Qty.) Plate Tap Cutter Pin Arm Pin Clip Cone Cutter Cylinder Cutter Washer 740 ( ) /2" 2/8" 74 (3900) 742 (2) (4000) 743 B (4400) 744 (2) (4700) 745 (2) (4800) 747 (2) (4900) 748 (8) (5000) /8 ( ) (06900) 3062 S (3) (069300) 3043 (068500) 3364 (3) (075200) 3365 (3) (075300) 3068 (3) (069400) 3047 (3) (068900) 3048 (3) (069000) /4 (405340) (06900) 3062 S (3) (069300) /4 (068700) 3364 (3) (075200) 3365 (3) (075300) 3068 (3) (069400) 3047 (3) (068900) 3048 (3) (069000) /4 (405300) 2/2" 2 3" 336 (074900) 3362 S (3) (07500) /4 (052400) 3364 (3) (075200) 3365 (3) (075300) 3368 (3) (075400) 337 (3) (025700) 338 (5) (025905) 339 (3) (026000) /8 (40530) 2/2" 2 3" 336 (074900) 3362 S (3) (07500) /8 (052600) 3364 (3) (075200) 3365 (3) (075300) 3368 (3) (075400) 337 (3) (025700) 338 (5) (025905) 339 (3) (026000) 060 3/4NC (40020) 3" (042000) 062 S (3) (042200) 033 3/4 (04000) 064 (3) (042300) 065 (3) (042400) 068 (3) (042500) 047 (3) (04700) 048 (5) (04800) 060 7/8THD (405640) 3" (042000) 062 S (3) (042200) 033 7/8 (0400) 064 (3) (042300) 065 (3) (042400) 068 (3) (042500) 047 (3) (04700) 048 (5) (04800) 060 NF ( ) 3" (042000) 062 S (3) (042200) 033 (040900PT) 064 (3) (042300) 065 (3) (042400) 068 (3) (042500) 047 (3) (04700) 048 (5) (04800) 960 ( ) 3 3/8" 4/8" 96 (038900) 762 S (3) (032800) 543 7/8 (027300) (3) (54900) 765 (3) (032900) (3) (5500) 947 (3) (038700) 948 (27) (038800) 749 (3) (03900PT) 760 ( ) 3/2" 3 4/2" 76 (032600) 762 S (3) (032800) 743 (03200) (3) (54900) 765 (3) (032900) (3) (5500) 747 (3) (03700) 748 (24) (03802) 749 (3) (03900PT) 760 /8 (404850) 3/2" 3 4/2" 76 (032600) 762 S (3) (032800) 743 /8 (7620) /8" (3) (54900) 765 (3) (032900) (3) (5500) 747 (3) (03700) 748 (24) (03802) 749 (3) (03900PT) 5060 AS ( ) 4/2" A (086900) 562 S (3) (027900) 843 (034900) 5043 A /8" 564 (3) (028000) 565 (3) (02800) 568 (3) (028200) 747 (3) (03700) 748 (24) (03802) 749 (3) (03900PT) /2" 6" S (4) (58200) A (4) (54900) (4) (55000) (4) (5500) 27 (4) (025400) C 79 (2) (28700) 749 (4) (03900PT) /8 6" 5 7/8" 3604 (56200) S (4) (58200) /8" N.F (4) (58300) (4) (57900) (4) (58000) (4) (59200) (2) (6000) (4) (5800) /8 6" 5 7/8" 3604 (56200) S (4) (58200) (4) (58300) (4) (57900) (4) (58000) (4) (59200) (2) (6000) (4) (5800) /8 (40670) 6/2" C (57200) S (4) (58200) B (54200) AC (57500) /8" (4) (58300) (4) (57900) (4) (58000) (4) (59200) (2) (5900) (4) (5800) " S (4) (58200) 8293 (00) A (4) (58300) (4) (57900) (4) (58000) (4) (59200) (2) (5900) (4) (5800) /2" 8/2" S (4) (58200) 8293 (00) A (5) (58300) (5) (57900) (5) (58000) (5) (60200) (5) (5900) (5) (5800) ( ) 8 7/2" 9/2" 3874 (60500) S (4) (58200) 8293 (00) A (60600) (5) (58300) (5) (57900) (5) (58000) (5) (60200) (5) (6000) (5) (5800) Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 07
25 Type 5 Self Feed Clip Type Wing Arm s 3/4 " 9" I.D. for Curved Tubes and Pipe Wing arm heads, components and (ordering numbers) Tube I.D. Closed Epand To Spider Arm Universal Plate Tap Cutter Pin Arm Pin Clip Cone Cutter Cylinder Cutter Washer 740 C (405890) 2" /2" 2/8" 74 (3900) 742 (2) (4000) 45 W ( ) 744 (2) (4700) 745 (2) (4800) 747 (2) (4900) 748 (8) (5000) 3060 C S (3) 45 ( ) 3364 (3) (075200) 3365 (3) (075300) 3068 (3) 3047 (3) 3048 (3) 3360 ( ) 2 2 3" 336 (074900) 3362 S (3) (07500) 3333 (409500PT) 3364 (3) (075200) 3365 (3) (075300) 3368 (3) (075400) 337 (3) (025700) 338 (5) (025905) 339 (3) (026000) /4 (40528) (042000) 062 S (3) (042200) /4 ( ) 064 (3) (042300) 065 (3) (042400) 068 (3) (042500) 047 (3) (04700) 048 (5) (04800) /8 ( ) (042000) 062 S (3) (042200) 353 7/8 ( ) 064 (3) (042300) 065 (3) (042400) 068 (3) (042500) 047 (3) (04700) 048 (5) (04800) 960 C ( ) 3/2" 3/8" 4 96 (038900) 762 S (3) (032800PT) 55 ( ) (3) (54900) 765 (3) (032900) (3) (5500) 947 (3) (038700) 948 (27) (038800) 749 (3) (03900PT) 760 C ( ) 3 3 4/2" 76 (032600) 762 S (3) (032800PT) 5 ( ) (3) (54900) 765 (3) (032900) (3) (5500) 747 (3) (03700) 748 (24) (03802) 749 (3) (03900PT) 760 C /8 ( PT) 3 3 4/2" 76 (032600) 762 S (3) (032800PT) 505 E (404884) /8" (3) (54900) 765 (3) (032900) (3) (5500) 747 (3) (03700) 748 (24) (03802) 749 (3) (03900PT) 5060 A ( ) 43/6" A (086900) 562 S (3) (027900) 505 E (404884) 5043 A (085400) /8" 564 (3) (028000) 565 (3) (02800) 568 (3) (028200) 747 (3) (03700) 748 (24) (03802) 749 (3) (03900PT) C 5 4/2" 6" S (4) (54800) 505 H ( ) A /8" (4) (54900) (4) (55000) (4) (5500) 27 (4) (025400) C 79 (2) (28700) 749 (4) (03900PT) C (406600) 6" 5 7/8" 3604 (56200) S (4) (58200) 505 H ( ) A (56400) /8" (4) (58300) (4) (57900) (4) (58000) (4) (60200) (2) (6000) (4) (5800) C (406800) 6/2" C (57200) S (4) (58200) 505 H ( ) AC (57500) /8" (4) (58300) (4) (57900) (4) (58000) (4) (60200) (2) (6000) (4) (5800) C 7 6 8" S (4) (58200) 225 A ( ) A (4) (58300) (4) (57900) (4) (58000) (4) (60200) (2) (6000) (4) (5800) C 7 6/2" 8/2" S (5) (58200) 225 A ( ) A (5) (58300) (5) (57900) (5) (58000) (5) (60200) (5) (6000) (5) (5800) C 8 7/2" 9/2" S (5) (58200) 225 A ( ) A (5) (58300) (5) (57900) (5) (58000) (5) (60200) (5) (6000) (5) (5800) 08 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
26 Drill s Drill s Tube I.D. range /2" thru 3 Airetool drill heads are made from alloy steel For strength and durability Drills can be used with etensions (below) for larger tube I.D. s as required Universal coupling ordered separately Tube I.D. Drill Order Hard Surfaced Hard Surfaced Order Drill O.D. Stud Thread Size of Flutes /2" MD NA 7/6" MD NA /2" /6" 3/6" MD NA /8" MD NA /8" MD NA 3/6" 7/6" S /6" 7/6" /2" S /2" S S S 0702 /6" S " 63/ /4S " S " 4 /2" S /2" 9" S *9" S /8" " S /8" Weight (Lbs.) Drill Etensions Male to Female Thread Description Male Female Male Female /8" Male /8" Female Length (in.) Model No. Order No. Model No. Order No. Model No. Order No A 03200PT B 03220PT C PT 5056 A A D PT 5056 B B C C D D E E H PT 5056 F F Distributed by: Practical Tools Inc / practicaltools@bellnet.ca 09
27 Epanding Blade Type Epanding Blade Type Tube I.D. range /2" thru 4/2" When ordering specify the motor number and the motors shaft thread size ( ) 2780 ( ) 6480 ( ) 2980 ( ) 680 ( ) 2680 ( ) 380 7/6 NF ( PT) /8 ( ) /8 NF ( PT) /6 NF (405740PT) 780 ( PT) 880 ( PT) 980 (40500PT) 2380 C (405600PT) 2380 (405500PT) 2680 S (406000PT) ( ) ( PT) H Tube I.D. Minimum Diameter Maimum Diameter Stud Size /2" 29/64" 37/64" 032 9/6" /6" /6" 3/6" 3/6" 25/32" 29/32" 3/32" 5/32" /8" /32" 5/32" 9/32" /2" 9/32" /2" /2" /6" /2" 3/6" 2/6" 2" 23/6" 2/8" /2" 2/8" " /2" 3/8" 3 4" 3 4/8" 4/2" 4/8" 4 9/6" Blade Body 248 (057700) 308 (069500) 278 (063800) 298 (066400) 298 (066400) 68 (089900) 68 (089900) 38 (070700) 38 (070700) 38 (070700) 38 (070700) 78 (048200PT) 88 (050600PT) 88 (050600PT) 88 (050600PT) 238 (054700PT) 268 S (3600PT) Rear Retainer 2483 (057800) 3083 (069600) 2783 (063900) 2983 (066500) 2983 (066500) 683 (090000) 683 (090000) 383 (070800) 383 (070800) 383 (070800) 383 (070800) 783 (048400PT) 883 (050900PT) 883 (050900PT) 883 (050900PT) 2383 (055750PT) 2683 S (36200PT) Blade Set 2487 ( ) 3087 ( PT) 2787 ( ) 6487 ( ) 2987 ( ) 687 (400030PT) 2687 ( PT) 387 ( ) 6387 ( PT) 6587 ( ) 6587 ( ) 787 ( ) 887 (400020PT) 987 ( PT) 2387 C ( PT) 2387 ( ) 2587 ( ) ( ) 248 (33500) 2483 (33600) 2587 ( ) ( ) 208 (22000PT) 2078 (6600) 2078 (6600) 2078 (6600) 2078 (6600) 2083 (22900PT) (6700) (6700) (6700) (6700) 2087 ( ) Blade 2487 (4) (058300) 3087 (3) (069700) (3) (064000) 6487 (3) (095800) 2987 (3) (066600) 687 (4) (09000) 2687 (4) (062500) 387 (4) (070900) 6387 (4) (092400) 6587 (4) (09800PT) 6587 (4) (09800PT) 787 (4) (048700) 887 (4) (05200PT) 987 (4) (05700PT) 2387 C (4) (055900PT) 2387 (4) (055800PT) 2587 (4) (3500PT) 2587 (4) (3500PT) 2587 (4) (3500PT) 2087 (6) (23300PT) 2087 (6) (23300PT) FF 00 (249800) FF 22 (245700) FF 22 (245700) FF 32 (248600) FF 337 (250500) FF337 (250500) FF337 (250500) FF 34 (248700PT) FF337 (250500) FF337 (250500) FF34 (250500) FF 5656 (250900PT) FF 66 (247000) FF 66 (247000) FF 66 (247000) FF 66 (247000) FF 66 (247000) FF 77 (247500) FF 78 (247700) Tap 032 7/6" 7/6" 9/6" FF 88 FF (245300PT) (6) FF (245300PT) ( ) ( ) (6) (6800) (6) (800) FF (248200) FF (248200) H H (6) FF (248200) /8" /8" /8" 0 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
28 UJoints 032 thru thread combinations For adapting cleaning heads to cleaning motors Ujoints, components and ordering numbers Universal Jont No. Jaw Jaw Link Pin (2 req.) UJoint O.D. (in.) Overall Length (in.) Thread Size Cleaner Kits Used On 245 ( ) 2452 (05700) 2452 (05700) 2454 (057200) 2455 (057300) PA 305 ( ) PA 3052 (294500) PA 3052 (294500) PA 3054 (294600) PA 3055 (294700).437 (.375 He) , 27 A, 30, 30 A 645 ( ) 6453 V (094800) 6453 V (094800) 6454 V (09500) 6455 V (095200) X B 6453 V (094800) 6457 V (095300) 6454 V (09500) 6455 V (095200) N.F X C ( ) 6452 V (094600) 6453 V (094800) 6454 V (09500) 6455 V (095200) X 60, X 6 65 (409600PT) 6452 V (094600) 6452 V (094600) 6454 V (09500) 6455 V (095200) X 6 65 B ( ) 6452 V (094600) 6457 V (095300) 6454 V (09500) 6455 V (095200) X ( ) 2652 (06700PT) 2652 (06700PT) 2654 (06900) 2655 (062000) , B ( ) 6652 (0000) (00300) 6655 (00400) X B ( ) 665 ( ) 6652 (0000) 6652 (0000) 6658 (00700) 6653 (00200) 6654 (00300) 6654 (00300) 6655 (00400) 6655 (00400) /6" 7/6" X 65, X 66 3, X 63, X 65, X ( ) 6653 (00200) 6653 (00200) 6654 (00300) 6655 (00400) 7/6" 7/6" ( ) 453 (079700) 457 (080200) 454 (079900) 455 (08000) 9/6" /2" W ( ) 452 (079600) 453 (079700) 454 (079900) 455 (08000) /2" 740 C 45 ( ) 452 (079600) 452 (079600) 454 (079900) 455 (08000) 362, 375, 387, 3200, , 4225, 4237, 4250, (409500PT) 3552 (076800) 3332 (074000) 3554 (077500) 3555 (077700) ( ) 353 ( ) 3552 (076800) 3557 (077800) 3533 (076500) 3533 (076500) 3554 (077500) 3554 (077500) 3555 (077700) 3555 (077700) , /4 Rotor Thread 3540, /8 Rotor Thread Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
29 UJoints thru 38" thread combinations For adapting cleaning heads to cleaning motors Ujoints, components and ordering numbers Universal Jont No. Jaw Jaw Link Pin (2 req.) UJoint O.D. (in.) Overall Length (in.) Thread Size Cleaner Kits Used On 225 ( ) 3553 (077400) 3553 (077400) 3554 (077500) 3555 (077700) 25 ( ) 355 ( ) 3552 (076800) 3552 (076800) 3553 (077400) 3552 (076800) 3554 (077500) 3554 (077500) 3555 (077700) 3555 (077700) , , 4300 A, A 3552 (076800) 3552 (076800) 3554 A 3555 (077700) Deg. Restricterd (046500) 654 (029900) 255 (02530PT) 3/ (029900) 255 (02530PT) ( ) 2452 (33400) 553 (046500) 654 (029900) 255 (02530PT) , H ( ) 653 (029600PT) 653 (029600PT) 654 (029900) 655 (030200) 65 (409400) 652 (029400) 65 A 652 (029400) 653 (029600PT) 653 (029600PT) 654 (029900) 655 (030200) 654 A 655 (030200) , 3287, Deg. Restricterd 55 ( ) 652 (029400) 652 (029400) 654 (029900) 655 (030200) , 4425, 4450, 4450 A 205 ( ) 5 ( ) 52 (043600) 52 (043600) 2053 (2900) 53 (044000) 54 (04400) 54 (04400) 55 (044200) 55 (044200) , , 338, 3325, ( ) 5052 (085600PT) 53 (044000) 54 (04400) 5055 (086000) 55 (044200) /8" 3350 through ( ) 5052 (085600PT) 505 E 5052 (085600PT) 5057 (086800) 54 (04400) (04400) 5055 (086000) 5055 (086000) /8" /8" 448, 4500, , 4600, 4650, 472, H ( ) 5052 (085600PT) 5052 (085600PT) 54 (04400) 5055 (086000) /8" /8" 225 H ( ) 2252 (28500) 2257 (3000) 2254 (28800) 2255 (29000) 3500 through (409700) 2252 (28500) 2253 (28700) 2254 (28800) 2255 (29000) /8" N.F N.F 3975 through A ( ) 2252 (28500) 2252 (28500) 2254 (28800) 2255 (29000) N.F 2 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
30 Adapters These adapters are used to configure motors and heads in special applications where the standard Airetool offering does not match up on thread sizes. Female X Female Male X Male Male X Female Part Female X Female Part Male X Male Part Male X Female FF X X 032 MF 22 /4 X /4 FF X 5/6 MM X 5/6 MF 23 /4 X 5/6 FF 22 /4 X /4 MM 250 /4 X /4 MF 23 F /4 X 5/6 FF 23 /4 X 5/ /4 X 5/6 MF 32 5/6 X /4 FF 237 /4 X 3/8 MM 24 /4 X 7/6 MF 32 F 5/6 X /4 FF 32 5/6 X /4 MM /6 X /4 MF 33 5/6 X 5/6 FF 33 5/6 X 5/6 MM 33 5/6 X 5/6 MF 33 F 5/6 X 5/6 FF337 5/6 X 3/8 MM 33 F 5/6 X 5/6 MF 34 5/6 X 7/6 FF34 5/6 X 7/6 MM 337 5/6 X 3/8 MF 34 F 5/6 X 7/6 FF 374 3/8 X 7/6 MM /8 X 3/ /8 X /4 FF 374 F 3/8 X 7/6 MM 3737 F 3/8 X 3/8 MF 373 3/8 X 5/6 FF 376 3/8 X 5/8 MM 374 3/8 X 7/6 MF 373 F 3/8 X 5/6 FF 437 7/6 X 3/8 MM 374 F 3/8 X 7/ /8 X 5/6 FF 45 7/6 X /2 MM 437 7/6 X 3/8 MF /8 X 3/8 FF 456 7/6 X 9/6 MM 44 7/6 X 7/6 MF 374 3/8 X 7/6 FF 46 7/6 X 5/8 MM 456 7/6 X 9/6 MF 374 F 3/8 X 7/6 FF 47 7/6 X 3/4 MM 46 7/6 X 5/8 MF 43 7/6 X 5/6 FF 54 /2 X 7/6 MM 5056 /2 X 9/6 MF 43 F 7/6 X 5/6 FF 56 /2 X 5/8 MM 56 /2 X 5/8 MF 433 7/6 X 3/8 FF 56 F /2 X 5/8 MM 564 9/6 X 7/6 MF /6 X 7/6 FF 564 9/6 X 7/6 MM /6 X /2 MF 435 7/6 X /2 FF /6 X 9/6 MM /6 X 9/6 MF 435 F 7/6 X /2 FF 566 9/6 X 5/8 MM 566 9/6 X 5/8 MF 436 7/6 X 5/8 FF 567 9/6 X 3/4 MM 567 9/6 X 3/4 MF 436 F 7/6 X 5/8 FF 637 5/8 X 3/8 MM 568 9/6 X 7/8 MF 53 /2 X 5/6 FF 64 5/8 X 7/6 MM 56 9/6 X 743 /2 X 3/8 FF 65 5/8 X /2 MM 66 5/8 X 5/8 MF 543 /2 X 7/6 FF 66 5/8 X 5/8 MM 67 5/8 X 3/4 MF 543 F /2 X 7/6 FF 66 F 5/8 X 5/8 MM 68 5/8 X 7/8 MF 56 /2 X 5/8 FF 67 5/8 X 3/4 MM 77 3/4 X 3/4 MF 56 F /2 X 5/8 FF 68 5/8 X 7/8 MM 78 3/4 X 7/8 MF 57 /2 X 3/4 FF 77 3/4 X 3/4 MM 88 7/8 X 7/8 MF 563 9/6 X 3/8 FF 78 3/4 X 7/84 MM 8 7/8 X MF 565 9/6 X /2 FF 856 7/8 X 9/6 MM X MF 566 9/6 X 5/8 FF 86 7/8 X 5/8 MM 2 X /8 MF 567 9/6 X 3/4 FF 88 7/8 X 7/8 MM /8 X /8 MF 568 9/6 X 7/8 FF 8 7/8 X MM 33 3/8 X 3/8 MF 56 9/6 X FF 6 X 5/8 MF 63 5/8 X 5/6 FF 7 X 3/4 MF 637 5/8 X 3/8 FF X 943 5/8 X 7/6 FF X /8 MF 65 5/8 X /2 FF 8 /8 X 7/8 MF 656 5/8 X 9/6 FF /8 X /8 MF 68 5/8 X 7/8 MF 743 3/4 X 7/6 MF 743 F 3/4 X 7/6 MF 76 3/4 X 5/8 MF 7 3/4 X MF 7 3/4 X /8 MF 86 7/8 X 5/8 MF 86 F 7/8 X 5/8 MF 87 7/8 X 3/4 MF 8 7/8 X MF 8 7/8 X /8 MF 83 7/8 X 3/8 MF 6 X 5/8 MF 8 X 7/8 MF X /8 MF 3 /8 X 3/8 MF 38 3/8 X 7/8 MF 3 3/8 X 3/8 3
31 Fleible Connections Fleible Connections Use for connecting cleaning head to motor when cleaning tubes with short radius bends. Fleible connectors come complete with female/female couplings in lengths from 4 4 inches (02 356mm) A length C length Part Order Thread Size 246 A X 032 Core Diameter Cleaner Motor Options 246 C X X 646 C /4 X /4 30,27, X64 3/6" X 6462 /4 X 5/6 27, X64 X 66 A /6 X 5/6 X6 X 66 C /6 X 5/6 X6 266 A /8 X 5/6 296 A /8 X 3/8 29 X 636 A /8 X 7/6 X63,3 36 C /6 X 5/6 3 X 666 A /8 X 7/6 X 6662 A /8 X 7/6 X65, X A /6 X 7/6 46 A /8 X 5/ X65, X66 375, A /8 X 9/6 Male 4200, 4225, 4250 /2" 463 C /8 X 7/ /6 X / C /4 X 3/4 4300, C /4 X 9/6 Male 3225, 4300, C /4 X 5/ /8 X 9/6 Male 3200, C /8 X 3/4 4350, /8 X 7/8 4350, C /8 X 7/8 Male /8 X 9/6 Male 3250, C X 7/ C /8 X /8 3350, 3400, C /8 X 7/8 3350, 3400, /8 X 7/8 Male 3350, 3400, /8 X 3350, 3400, /8 X 3500 and up /8 X / and up /8 X 3/8 Male 3500 and up Type A Type C Appro. Length (in.) Wt. Appro. Length (in.) Wt..06# #.08# #.40#.25#.45# #.0#.5# # Not Available 3.# 4 Distributed by: Practical Tools Inc / practicaltools@bellnet.ca
Tube Cleaners Introduction
Tube Cleaners Introduction Clean tubes mean lower fuel costs. All piping, heat echangers, condensers, chillers, and boiler tubes accumulate scale over various periods of use. This scale decreases flow
More informationTube Cleaners Heat Exchanger & Condenser Cleaning Systems
System Components Motors CC475 & CC475PS I CC375 CC325 CC325HP s DRIVE COUPLING DRIVE SHAFT SHAFT COUPLING Drills and Brushes DRIVEN SHAFT CT DRILL TW DRILL AT DRILL CB DRILL SPIRAL BRUSH Complete Cleaning
More informationBoiler Tube Cleaners Tube Cleaners for Straight Tubes
Tube Cleaners for Straight Tubes 1/2" to 1-3/8" (12.7 to 34.9 mm) I.D. Range: 1/2 in. (12.7 mm) - 1-3/8 in. (34.9 mm) Deposit: heavy-medium to soft Midget Motor with optional heads shaft wrench; metal
More informationTube Cleaners.
Tube Cleaners www.elliott-tool.com Tube Cleaners Table of Contents Pg. Tube Cleaners 2 5370 Jiffy Gun 3 537100C Jumbo Jiffy Gun 4 Jiffy Gun & Jumbo Jiffy Gun Spares & Accessories 5 Soot Buster 5 Soot Buster
More informationTube Installation.
Tube Installation www.elliott-tool.com Tube Installation Table of Contents Page Tube Installation 2 Tube Hole Gauges 4 Tube Sheet Hole Brushes 5 Grooving (Serrating) Tools 6 Tube Auger / End Prep 7 Hand
More informationELECTRIC TUBE CLEANERS
ELECTRIC TUBE CLEANERS 1 4 &UP FLEXIBLE SHAFT CAN BE STORED ON HANDLE ELECTRIC TUBE CLEANERS QUICK CONNECT OF SHAFT TO CLEANER POWER INDICATOR LIGHT WATER IN-FLOW THROUGH STANDARD HOSE CONNECTOR LARGE
More informationHOSES & LANCES. Hoses & Lances 15,000 PSI (1,034 BAR)
HOSES & LANCES Jetstream provides a full arrangement of hoses and flex lances for high pressure waterblasting. The hoses and lances are designed to be durable and reliable for any 15,000 psi application.
More informationThomas C. Wilson, Inc. Tube Cleaning Equipment, Accessories and Supplies
Tube Cleaning Equipment, Accessories and Supplies WET AND DRY TUBE CLEANING SYSTEMS ELECTRIC, PNEUMATIC, AND AIR MOTORS SHAFTS AND CASINGS, BRUSHES, SCRAPERS, ACCESSORIES AND SUPPLIES Thomas C. Wilson,
More informationTube Plugs.
Tube Plugs www.elliott-tool.com Tube Plugs Table of Contents Page Tube Plugs Aluminum Siphons Boilers-Firetube Boilers-Watertube Sugar Mill Vacuum Pans Surface Condensers Chillers & Heat Exchangers Feedwater
More informationHelaGuard. Non-Metallic Conduit & Fittings
HelaGuard Non-Metallic Conduit & Fittings HelaGuard Non-Metallic Conduit Systems Page HelaGuard Overview 3 Conduit Application Overview 4 Mounting & Removing HelaGuard Non-Metallic Fittings 5 HelaGuard
More informationVISUAL INDEX Equipment
U R Hand Tube Benders Ratchet Hand Tube Bender 1 Hand Tube Bender BAV06/12 Combined Tube Bending & Cutting Tool BV06/18, BV20/25 Tube Bending Tools Benders R4-R5 R4 R5 R6 R6 Bender Capacity Guides Exactol
More informationThomas C. Wilson, Inc. Tube Cleaning Equipment, Accessories, and Supplies
Tube Cleaning Equipment, Accessories, and Supplies Tools for cleaning tubes in... heat exchangers Fire tube and water tube boilers Condensers, chillers, and absorbers and other tubular structures and pressure
More informationTubing Cutter for 1/16" Stainless Steel Tubing
Delivery Tubing and ccessories 311 P000257 Tubing Cutter for 1/16" Stainless Steel Tubing 58692-U Low-cost tool cuts 1/16" stainless steel tubing without obstructing the bore. Easily cut 1/16" OD stainless
More informationQuicklub Lubrication Systems Fittings, Adapters and Accessories
Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for divider valve mounting (6, 8, 10 and
More informationTube Remover and Installer. and Installer Used for servicing Ford systems produced after Screen Extractor. Ford Aerostar Expansion
gauges A/C FLUSH KIT Easy-to-use system removes refrigerant oil, moisture contaminants from system components lines during retrofitting compressor replacement. Kit includes rubber-tipped flush gun, canister
More information4405-RA 4405-R 4405-RA 4405-R S
ACCESSORIES Page 34 Master Parts Breakdowns Updated Feb. 1st 2006 Master Parts Breakdowns Updated Feb. 1st 2006 Page 35 This tool is designed to operate on 90 psig (6.2 bar) maximum air pressure with 1/4
More informationOutput 0.9 H.P. (675 W) 9000 to R.P.M (11000rpm is standard)
HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual COLLET SPINDLE SHOWN Model Number Exhaust Direction Throttle Type 44RAE Side (L) Lever or (K) Safety Lever Speed 9000 to 11000
More informationSpecial Applications Require Special Tools
Index Routers.................. 102-103 Tappers..................... 104 Clinch Nut Tools.............. 106 Rivet Shavers................ 107 Skin Clamp Runners........... 108 Saws................... 109-110
More informationQuicklub Lubrication Systems
Fittings, Adapters and Accessories Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for
More informationM-B Companies, Inc. Specification. Model 245. Self Propelled Intermediate Striper. High Pressure Airless. Options. Revised September 27, 2006
M-B Companies, Inc. Administration Pavement Marking Equipment Divisions 1615 Wisconsin Avenue EAST COAST DIVISION WEST COAST DIVISION P.O. Box 200 79 Montgomery Street 2490 Ewald S.E. New Holstein, WI
More informationCable Management Solutions. HelaGuard. Non-Metallic Conduits and Fittings
Cable Management Solutions HelaGuard Non-Metallic Conduits and Fittings Table of Contents Page HelaGuard Overview 4 Conduit Application Overview 6 Mounting & Removing HelaGuard Non-Metallic Fittings 7
More informationTools. Acid Brush. Utility Brush. Brushes For Cleaning Copper Fittings G113 01/06/18
Acid Brush G113 Manufactured with electrolyte tin plate and filled with 100% pure stiff black horse hair which is firmly crimped to eliminate bristle "fall out" Use with acid, flux and pipe dope 1/2" Acid
More informationCut Off and Deburring
Cut Off and Deburring Cut Off and Deburring Heavy Duty Pipe Cutters Heavy-Duty Pipe Cutters RIDGID Heavy-Duty Pipe Cutters for fast, burr-free cutting of steel pipes up to. Extra-long shank protects adjustment
More informationTX115/215 Hot-tap Insertion Turbine Instructions
TX115/215 Hot-tap Insertion Turbine Instructions General Information These hot tap versions of the proven TX insertion flow sensors are designed to install or be serviced without depressurizing the pipe.
More informationSERIES 36-AM & BD...4-5 SERIES 36-AM-RA & BD RA...6-7 SERIES 50-AM & BD...8-9 SERIES 36 TOOL CHANGER...10-11 SERIES 50-TOOL CHANGER...12-13 SERVO MOTOR ADAPTERS...14-15...16-17...18-19 COLLET NUT...19
More informationMillennium TM. 100 thru 675 Tons (315 thru 2375 kw) renewal parts. Supersedes: RP1 (1099) Form RP1 (710) R-22 and R-134a 00202VIP
Millennium TM Rotary Screw Liquid Chillers renewal parts Supersedes: 160.80-RP1 (1099) Form 160.80-RP1 (710) Model YS BA CB S0 thru YS FA FB S5 (Style E) 100 thru 675 Tons (315 thru 2375 kw) 00202VIP R-22
More informationAiretool. Gas Line Cleaners Range: 3/4 (19.05mm) to 1-1/2 (38.10mm) Operating & Service Manual PL EN 10/01/2015
Operating & Service Manual PL9-6026EN 0/0/205 Airetool Gas Line Cleaners Range: 3/4 (9.05mm) to -/2 (38.0mm) For additional product information visit our website at http://www.apextoolgroup.com PL9-6026EN
More informationQuicklub Lubrication Systems Fittings, Adapters and Accessories
Divider Valve Mounting Accessories 24646 Valve mounting bracket 5304 4" nylon locknut for valve mounting 247023 Grade 8, 4" valve mounting bolt 239499 Template for divider valve mounting (6, 8, 0 and 2
More informationSTANDARD SERIES VALVE SEAT CUTTERS (for use with standard series pilots,.375" top)
PA R T S L I S T STANDARD SERIES VALVE SEAT S (for use with standard series pilots,.375" top) 28.6mm 1-1/8" 31.8mm 1-1/4" 35mm 1-3/8"! OF 15 3 250 243 30 3 250 278 30 3 253 299 30 x 45 3/3 250 274 45 3
More informationSanders, Buffers & Polishers Introduction
Sanders, Buffers & Polishers Introduction Dotco sanders, buffers and polishers are available in a variety of styles and power ratings to provide flexibility in choosing the best tool for the job. Disc
More information2015 PRODUCTS & PRICES
2015 PRODUCTS & PRICES STOPS THAT ARE USER FRIENDLY Orders 1-800-821-3491 Phone 1-717-484-0230 Fax 1-717-484-0933 E-mail mayaposi@att.net Web mayaposi-stop.com MAYA POSITIONING EQUIPMENT MFG CO. INC. 940
More informationILLUSTRATED PARTS LIST
CW413 / TW413 WITH 390cc HONDA ENGINE 00-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 390cc
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More informationMODELS JG43, JG63, JG83 JG44, JG64, JG84
MODEL J STYLE G HERMETIC COMPRESSORS RENEWAL PARTS Supersedes: 180.23-RP4 (695) Form 180.23-RP4 (1298) MODELS JG43, JG63, JG83 JG44, JG64, JG84 (See Page 2 for Complete Model Nomenclature) 27531A UNIT
More information855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
More informationTX101/201 Insertion Turbine Instructions
TX101/201 Insertion Turbine Instructions General Information Sapphire bearings and a non-drag pick-off give these adjustable insertion turbine flow sensors a wide flow and long life. A Hall-effect device
More informationTX 115/215 Hot-tap Insertion Turbine Instructions
TX 115/215 Hot-tap Insertion Turbine Instructions General Information These hot tap versions of the proven TX insertion flow sensors are designed to install or be serviced without depressurizing the pipe.
More informationGROUP 3 HYDRAULICS 636 EXTENDO PARTS BOOK
GROUP 3 HYDRAULICS 636 EXTENDO ELECTRICAL SCHEMATIC FOR 636 & 5528, AL-11969... 3-4 ELECTRICAL PLUG-INS SCHEMATIC, BL-10012... 3-7 HYDRAULIC SCHEMATIC, AL-11355... 3-8 HYDRAULIC SCHEMATIC WITH OPTIONAL
More informationInternal Pressure Pipe Cutters. Manual E540
Internal Pressure Pipe Cutters Manual E540 Contents Logan Internal Pressure Pipe Cutters Overview...2 Uses...2 Construction...2 Tool Illustration...3 Operation...2 Single Cut from a Fixed Platform... 2
More informationOne Direct Source for all your Water Blasting Parts and Accessories!
table of contents One Direct Source for all your Water Blasting Parts and Accessories! SURFACE NOZZLES PAGE Drilled Nozzles 1 Standard Button Tip Flex Lance Nozzles 1 TLX Nozzle 1 Drilled Nozzle Flow Charts
More informationModel & AP (Air Purge) Condenser Cleaner
TM-81 October 13, 2004 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders tube rolling motors
More informationPneumatic Connector, Tubing, and Accessory Catalog
Pneumatic Connector, Tubing, and Accessory Catalog Pneumatic Quick Connectors Plastic Tubing and Adaptors Tube Connectors and Manifolds Plumbing Tools Contents Plastic Tubing 1 Plastic Tubing Specifications
More informationHYDRAULIC PUMPS. Performance under Pressure
HYDRAULIC PUMPS LARZEP Pumps are available in a wide range of models: Hand pumps, Air hydraulic pumps, Modular pumps, Manual, Electric, Air and Petrol hydraulic powerpacks, Split-Flow powerpacks, Hydrotest
More informationDIAMOND CONCRETE SAW PARTS LIST MODEL CC8000 P R O D U C T S. (Revised )
DIAMOND P R O D U C T S CONCRETE SAW PARTS LIST MODEL CC8000 (Revised 10-15-2002) Table of Contents Page Saw Controls Legend. 3 Drawing 1. Frame Group. 4-5 Drawing 2. Arm Assembly... 6-7 Drawing 3. Hydraulics
More informationILLUSTRATED PARTS LIST
BD300 WITH 277cc KOHLER ENGINE 00-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 277cc 2 WHEEL
More informationILLUSTRATED PARTS LIST
CW300 WITH 265cc SUBARU ENGINE 800-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 265cc 2
More informationGeneral Safety and Maintenance Manual. Output. Type 0.9 H.P.675 W. (L) Lever or (K) Safety Lever R.P.M. (18000PM is standard)
HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual SUPER EXTENDED LENGTH DIE GRINDER FEATURING FRONT END DOUBLE ROW BEARINGS FOR SUPPORT. Multiple accessory mounting is possible
More informationM-5000TG/5700TG Steam and Cold Water Mixing Unit
M-5000TG/5700TG Steam and Cold Water Mixing Unit Installation, Operating and Maintenance Instructions Last Updated: October, 2012 Strahman Valves, Inc. USA Headquarters 2801 Baglyos Circle Bethlehem, PA
More informationSUPER TUBE-TUGGER Continuous Tube Extractor For 1-1/2 2 Tube OD ( )
www.elliott-tool.com TM-42 Rev. 9/20/04 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders
More informationInstallation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware
More informationM-5000TG/5700TG Steam and Cold Water Mixing Unit
M-5000TG/5700TG Steam and Cold Water Mixing Unit Installation, Operating and Maintenance Instructions Last Updated: August, 2014 Strahman Valves, Inc. USA Headquarters 2801 Baglyos Circle Bethlehem, PA
More informationForm No Parts List for: MODEL B ELECTRIC HYDRAULIC PUMP. Maximum Capacity: 10,000 PSI PE55TWP-IBT-115. Sheet No. 1 of 8
Parts List for: Form No. 1000457 PE55TWP-IBT-115 MODEL B ELECTRIC HYDRAULIC PUMP Maximum Capacity: 10,000 PSI 1 2 3 7 SPX Hydraulic Technologies, Rockford, IL 61109 USA www.powerteam.com Made in USA 309219Rev7
More informationSELF-FEED DRILL UNITS MK III BROOMATIC SALES/ENGINEERING FEATURES
SELF-FEED DRILL UNITS MK III BROOMATIC SALES/ENGINEERING FEATURES The Building Blocks of Low Cost Drilling and Tapping Automation Table of Contents PAGE 1 FIG. 1 PNEUMATIC MK III WITH STANDARD 3/8 CAPACITY
More informationAdvanced Artillery For Enhanced Tubes
Advanced Artillery For Enhanced Tubes BRUSHES DESIGNED TO CLEAN THE INTERNAL LANDS & GROOVES Brushes for internally enhanced tubes Available in Bags of 25 Tube O.D., I.D., & Gauge (B.W.G.) A Tube O.D.
More informationAIR DRIVEN TUBE CLEANER
MODEL PGX-2 AIR DRIVEN TUBE CLEANER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 5/11/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C.
More informationRegenerative Turbine Pumps
Bulletin 40 October 008 40 40 80 80 Series Regenerative Turbine Pumps Capacities to 60 GPM Heads to 800 Feet MTH PUMPS 40 40 80 80 Series regenerative turbine pumps represent the most economical, high
More informationA M Supply Co. Hand Tools Metal Cutting. Metal Cutting. Lenox Seamers. Snips. Milwaukee Snip Sets. Snips. Phone:(405) (800)
Metal Cutting Lenox Seamers Part # L22210 Description 3" Seamer Snips Metal Cutting Milwaukee Snip Sets Part # Description Cut Cap Sheet Metal Cut Cap Stainless L22101 Aviation Snip Left 18 ga 22 ga L22102
More informationPARTS LIST. Reproduction. Not for. Models Mfg. No. Description Pico 6, SP 44cm Walk Behind, CE (2010)
PARTS LIST Models Mfg. No. Description 884142 Pico 6, SP 44cm Walk Behind, CE (2010) Manual Part No. 1739809 Revision B Rev. Date: 1/13/2011 Table Of Contents PRODUCT COMPONENTS PAGES Handle, Controls
More information767 Hydraulic Hand Pump
INSTRUCTION MANUAL 767 Hydraulic Hand Pump Serial Code ABM Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
More informationCopper Sleeve, Unit Injector, Replacement
Volvo Trucks North America Greensboro, NC USA This service bulletin replaces SB 237-46, Copper Sleeve, Unit Injector, Replacement dated 6.2007, publication no. PV776-20177417. DService Bulletin Trucks
More informationP O W E R P U M P S SECTION INDEX. Proper Size & Selection G1 Series Electric...
SECTION INDEX Proper Size & Selection... 44-45 G1 Series Electric... 46-47 2 Series Electric... 48-49 G3 Series Electric... 5-51 G4 Series Electric... 52-53 P O W E R P U M P S G5 Series Electric... 54-55
More information150 PSI ILLUMINATED DASH PANEL GAUGE KIT
150 PSI ILLUMINATED DASH PANEL GAUGE KIT PART NO. 10061 (For Use with 20/30 Amp Systems) PART NO. 20062 (For Use with 30/40 Amp Systems) IMPORTANT: It is essential that you and any other operator of this
More informationTX101/201 Insertion Turbine Instructions
TX101/201 Insertion Turbine Instructions General Information Ruby bearings and a non-drag pick-off give these adjustable insertion turbine flow sensors a wide flow and long life. A sensor detects the passage
More informationHENRY TOOLS. General Safety and Maintenance Manual MODELS 4402-RAS 4402-RASK 4402-RASC
HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual K C Model Number 4402RAS 4402RAC Exhaust Direction Front or Side Throttle Type (L) Lever or (K) Safety Lever Speed 13500 R.P.M.
More information2018 High Performance Check Valves for liquid and gaseous media
2018 High Performance Check Valves for liquid and gaseous media Check valves Catalogue 45 Date: 04/2018 WEH - We Engineer Hightech All rights reserved, WEH GmbH 2018. Unauthorized copies are strictly forbidden
More informationFeatures and Specifications for Impact Wrenches
Pneumatic Air Tools Version 2017 Revised 06/2017 Email your order to: sales@polyconn.com or fax to (763) 398-2590. www.polyconn.com. Questions call: (763)559-0388 3062 Ranchview Lane North. Plymouth, MN
More informationLubrication Installation Components, Accessories & Fittings Table of Contents
Lubrication Installation Components, Accessories & Fittings Table of Contents Lubrication Fittings & Accessories: Introduction............................................. 2 Threaded Fittings........................................
More informationBRASS FITTINGS and Related Products
Discount Hydraulic Hose.com Cat. BR602 February, 2006 Prices Subject to change BRASS FITTINGS and Related Products Air Brake Fittings: Nylon Tubing 2 Push-In Air Brake Fittings 4 Pre-Assembled Air Brake
More informationGRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL
GRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL Grain Carts KITS Thunderstone Manufacturing, LLC. 3400 West O Street Lincoln, NE 68528 402-435-4249 (Fax) 402-438-3918 www.thunderstonemfg.com Aluminum
More informationIn-Line Positive Feed Tools
In-Line Positive Feed Tools ADVANCED DRILLING EQUIPMENT SP-1300-1-EN-0806-.25M 1-1 Introduction In-Line Positive Feed Tools How Positive Feed Drills Operate Our in-line positive feed drills use two interconnected
More informationMK-5000G exploded VieW
Frame accessories 38 cutting head Pump Assembly 39 connecting linkage foot pedal linkage 40 curtain blade guard 41 ENGINE Assembly 42 PARTS LIST A Frames - - A1 Frame, MK-5000 Main 1 155541 B Pivot Bracket
More informationINSTALLATION INSTRUCTIONS
28 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY 2-5 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationPTTC Tube Cutter (Push Type Tube Cutter)
PTTC Tube Cutter (Push Type Tube Cutter) For Tube OD Range 3/8 and 5/8-2-1/2 Tube & Pipe Cleaners Tube Testers Tube Plugs Tube Removal Tube Installation Operating and Maintenance Instructions www.elliott-tool.com
More informationTech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800)
SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.hytec.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Parts
More informationForm No Parts List for: MODEL B HYDRAULIC PUMP GENERAL SECTION PG PG553-2UK FT600 PG554. PG120A Series Y70G Series. Sheet No.
MODEL B HYDRAULIC PUMP GENERAL SECTION Parts List for: Form No. 100520 60208 PG553 65820 PG553-2UK FT600 PG554 FT700-001 PG554-LEAD FT700-002 PG554-2UK PG55A Series Y26G Series PG90A Series Y60G Series
More informationHVAC PLUMBING TOOLS CATALOG 2019 F-1. PIPE cutters. Excellent for cutting tubing insulation Strong nylon handle
hand tools PIPE cutters Excellent for cutting tubing insulation Strong nylon handle Ratchet action 1-5/8-Inch capacity Heat treated blade 36101 Little Tubing Cutter EA 10 36102 2 Replacement Blades PK
More information10.5 gal. Vertical Oil Lubricated Air Compressor
10.5 gal. Vertical Oil Lubricated Air Compressor Model No. AC1104 Tank volume: 10.5 gal. (40 L) Direct drive Oil-lubricated single cylinder pump for durability and long life triple the pump life of comparable
More informationSWING CHECK VALVES SERIES 52-SC SERIES 600
SWING CHECK VALVES SERIES 52-SC SERIES 600 FEATURES/BENEFITS/SPECIFICATIONS AMERICAN Flow Control Series 52-SC Swing Check Valves incorporate design features to help increase service life for water and
More informationFire Protection. FP-XA End Suction
Fire Protection FP-XA End Suction PRODUCT BULLETIN MODEL FP-XA END SUCTION CPS Model FP-XA End Suction pumps are used in a variety of fire fighting applications. These rugged and efficient centrifugal
More informationU1 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 060-064 - 130-134 - 133-U1 PUMP PARTS PRICE LIST DESCRIPTION QTY. PER PUMP 060-U1 Pump Body 1 See Note 1 1 060-U1 Pump Body with Flush 1 See Note 1 1 064-U1 Rectangular Flange Inlet Body 1
More informationThomas C. Wilson, Inc. Short Quick Reference BOILERS CONDENSERS HEAT EXCHANGERS EVAPORATORS CHILLERS / ABSORBERS COOLERS
Short Quick Reference Tools for the maintenance and repair of... BOILERS CONDENSERS HEAT EXCHANGERS EVAPORATORS CHILLERS / ABSORBERS COOLERS Thomas C. Wilson, Inc. The Wils-Away 1000 Cleaning a Fire Tube
More informationTAPS & DIES S.T.I. TAPS - HIGH SPEED GROUND MACHINE SCREW SIZES FRACTIONAL SIZES
S.T.I. TAPS - HIGH SPEED GROUND High quality tap S.T.I. taps are oversize to rethread damaged threads Available in plug and bottoming style only MACHINE SCREW SIZES Plug Bottom Nominal H # of Thread Overall
More informationThrottle Type (L) Lever or (K) Safety Lever. Weight Length Diameter Air Aluminum Steel. 9.1 Inches (231 mm) 3.5 Lbs (1.6 Kg)
HENRY TOOLS Industrial Airtools at Wk General Safety and Maintenance Manual C C MODEL 46RAS shown with 4 Guard. MODEL 46RAC with 1/4 Collet f use with mounted points carbide burrs. Model Exhaust Number
More informationSERIES TBS INSERTION TURBINE TBS-0XX TBS-1XX
F- SERIES INSERTION TURBINE instructions -0XX -1XX Table of Contents GENERAL INFORMATION General Information Features, Specifications... Page 1 Installation Piping, Immersion, Positioning the Meter...
More informationQuality Value Assurance
Pump Selection Guide Quality Value Assurance In the beginning From it s inception in 1990 with one man in a service van, to the industry leader in innovative dairy solutions that DariTech is today, we
More informationTable of Contents. Standard Taps
Table of Contents Standard Taps Standard Taps--High Speed Steel Machine Screw Sizes... 3 Standard Taps--High Speed Steel Hand Taps (Fractional Sizes)... 5 Standard Taps--High Speed Steel Machine Screw
More informationAiretool. CC-325-HP High Pressure Water Flush Condenser Tube Cleaner. Operating & Service Manual IM 05/11/2011
Operating & Service Manual 90093-IM 05/11/2011 Airetool CC-325-HP High Pressure Water Flush Condenser Tube Cleaner For additional product information visit our website at http://www.apextoolgroup.com Safety
More informationIndex. Butterfly Valves
Dry Bulk - Chemical - Petroleum Dry Bulk - Chemical - Petroleum Nozzles Nozzles & Valves & Index Index Part No. Description Page Nozzles P- 202 Overwing Aircraft Refueling, Bronze 1 P- 2022 Overwing Aircraft
More informationHigh Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
More informationQGD-20/25/30 & QGD-40/50
QGD-0/5/0 & QGD-40/50 Direct Drive Rotary Screw Air Compressor Parts Manual This manual contains important safety information and should be made available to all personnel who operate and/or maintain this
More informationILLUSTRATED PARTS LIST
TW400 WITH 390cc HONDA ENGINE 00-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 390cc 2 WHEEL
More informationU1 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 PUMP 030-U1 Pump Body 1 See Note 1 1 030-U1 Pump Body with Flush 1 See Note 1 1 034-U1 Rectangular Flange Inlet Body 1 See Note 1 1 034-U1 Rect. Flange Inlet Body with Flush 1 See Note 1 1
More informationMicrobore Hose, Assemblies & accessories
bar DN2 and DN4 High pressure Microbore hose Technical data Microbore hose The microbore hose assembly, most commonly used to connect to a Minimess test point for pressure testing, has many other diverse
More informationValves, MRO Items, Heaters, Thermocouples, and so much more
Nozzle Tips, Nozzle Bodies, Valves, MRO Items, Heaters, Thermocouples, and so much more (800) 521-0704 Fax: (810) 227-2266 37 Summit Street, Brighton, MI 48116 37 Summit Street, Brighton, MI 48116 810.227.2266
More informationTugger T-Bolts Coupling (Extension) Nuts Eye Bolts Metric Coupling (Ext.) Nuts Latch Swing Bolts Heavy Hex Nuts...
INDEX Threaded Rod... 4 T-Slot Nuts... 14 Driver Studs - Stainless Steel... 4 Stainless Steel T-Nuts... 14 Driver Studs... 4-5 Stainless Steel Flange Nuts... 15 Driver Studs Various Thread Lengths... 6
More informationHot Sprue Bushings Products/Technical Guide
Hot Sprue Bushings Products/Technical Guide USB8 And SB8 Hot Sprue Bushings Notes 1. Cold bushing length must allow for thermal expansion to fit specified mold length. 2. For special "A" length order next
More informationForm No , 3 4, 5 VALVE DETAIL DIVISION UNEX CORPORATION. Parts List for: HYTORC-115 HYTORC-230 HYTORC MODEL D ELECTRIC HYDRAULIC PUMP
> Parts List for: Form No. 105548 DIVISION UNEX CORPORATION 333 STATE ROUTE 17 NORTH MAHWAH, N.J. 07430-9895 Tel: (201) 512-9500 Fax: (201) 512-0530 HYTORC-115 HYTORC-230 HYTORC-230-2 MODEL D ELECTRIC
More informationAvailable with T93R MAXX Tip & Guard
7500 PSI (500 BAR) Maximum Pressure Airless Gun High-strength aluminum alloy handle is light-weight, solid and strong single piece forging that features an anodized protective finish that is highly corrosive
More informationFast, Effective Blowout Protection
Dual or Single Ram Hydraulic BOPs Fast, Effective Blowout Protection MODEL DRH - DUAL RAM HYDRAULIC BOP Guide Rib Pipe Centering Guide Ram Rubber Pipe Ram Block Door Cylinder Locking Shaft Lip-Type Piston
More informationRL-H80 PARTS LIST # H USE THIS PARTS LIST FOR: Hoist Serial Number 2733 to
RL-H80 PARTS LIST # 102837H USE THIS PARTS LIST FOR: Hoist Serial Number 2733 to For older hoists use the following: Parts List No. 102837G for Serial Number 2485 to 2732 IF YOUR HOIST DOES NOT FALL WITHIN
More information