M-B Companies, Inc. Specification. Model 245. Self Propelled Intermediate Striper. High Pressure Airless. Options. Revised September 27, 2006

Transcription

1 M-B Companies, Inc. Administration Pavement Marking Equipment Divisions 1615 Wisconsin Avenue EAST COAST DIVISION WEST COAST DIVISION P.O. Box Montgomery Street 2490 Ewald S.E. New Holstein, WI Montgomery, PA Salem, OR Phone: Phone: Phone: FAX: FAX: FAX: Specification Model 245 Self Propelled Intermediate Striper High Pressure Airless Options Revised September 27, 2006 This specification describes options for an M-B model 245 High Pressure Airless Self- Propelled Striper and is for reference only. The M-B Companies reserve the right to change this Standard specification without notice. Thus, it is important that final specifications per customer requirements, (replace standard with Customer name) be completed by M-B as close as possible in time for bid. Please consult M-B Companies Sales department with any questions or requests.

2 Page 2 of 9 It is the intent of this specification to describe and define all options for a 245 High Pressure Airless Self Propelled Striper. The format of this specification is itemized form for ease of topic definition and topic reference. Table of Contents 1. Agitator, Air Driven (No heat) 2. Agitator, Hydraulic Driven 3. Arrowboard 4. Auxiliary Engine: Honda 5. Carriage Assembly, Sliding 6. Cleaning Solution System, 20 Gallon 7. Crosswalk Gun Carriage 8. Fire Extinguisher 9. Fourth Paint & Bead Gun 10. Heat System, single color 11. Heat System, dual color 12. High Pressure Piston Paint Pump, 12.9 GPM 13. Paint Handgun 14. Paint Storage Reservoir, 60 Gallon 15. Paint Storage Reservoirs, 120 Gallon 16. Rear Bumper / Drop Platform 17. Rotating Beacon 18. Second Cover Assembly / Drum Hold Down 19. Second High Pressure Piston Paint Pump, 8.6 GPM 20. Spare Tire 21. Strobe Light 22. Transfer Pump 23. Windshield 24. Work Lights

3 Page 3 of 9 1. Agitator, Air Driven (No Heat) 1.1. No heat available with this option 1.2. Two stainless steel paddles, minimum 1.3. Drive motor has a valve to control paddle speed 2. Agitator, Hydraulic Driven 2.1. Two stainless steel paddles, minimum 2.2. Drive motor has a valve to control paddle speed 3. Arrowboard x 48 arrowboard, 13 lamp 3.2. Hooded, seal beam amber lighting 3.3. Mounted behind canopy Volts DC 3.5. Solid State circuit control 4. Auxiliary Engine: Honda hp, gas cylinder, 4.3. Fuel supply from chassis 5. Carriage Assembly, Sliding 5.1. Front side shift sliding Slide position set by hydraulic motor driven gears against two racks Hydraulic power provided by auxiliary engine Floating for constant pavement relationship Square tube welded construction Three caster wheel design One for overall support of chassis Two for floating carriage Retracting for near vertical storage, transport, and accessibility for gun servicing Lift provided by electric winch 5.2. Air manifold (for paint bead on / off solenoids) Machined aluminum manifold to support all paint and bead gun solenoids Individual solenoid for each gun Stainless steel body ¼ npt ports Brass manual petcock between the manifold and each control solenoid Air control line to gun 3/8 O.D Color coded: Blue Fiber braid reinforced Nylon Meets SAE J844 type B, DOT FMVSS Cleaning Solution System, 20 Gallon gallon stainless steel solvent tank, pressure pot system ASME certified pressure vessel lb. safety relief valve with gauge and regulator mounted at tank top

4 Page 4 of psi working, 165 psi test Tank clearly labeled CLEANING SOLUTION pipe plug for loading Tank drain quarter turn valve at bottom of the tank ¾ S/S check valve near outlet to prevent paint back-up into cleaner tank 6.2. Cleaning available to all paint wetted lines At each tank outlet there shall be a ball valve located within 18 of tank outlet to flush the downstream paint system and crossover line At paint manifold Air blow down system shall be incorporated after cleaner tank to allow air to be forced through each individual line before and after flushing with cleaner Cleaning solution lines Color coded: Red Fiber braid reinforced Nylon Meets SAE J844 type B, DOT FMVSS Garden hose attachment Valved connection point to attach water source 7. Crosswalk Gun Carriage 7.1. Use paint and bead supply from striper feet paint and bead hose 7.3. One Graco high pressure type paint gun Adjustable width line One glass bead gun 7.5. Well balanced and short frame Welded steel construction, torsionally rigid Three wheels X 1.75 ball bearing for low resistance pushing 7.6. Air control for each paint spray gun 7.7. Gun mount and bar positioned right or left side of unit Adjust up and down, left and right for operator adjustable gun placement Allow each gun to be positioned independent of any other gun 8. Fire extinguisher lb. dry powder type 8.2. Mounted on canopy post 9. Fourth Paint & Bead Gun (max of three guns can be run at any time) 9.1. One Kamber 50-A, no exceptions, high pressure type paint gun " line width, thickness Corrosion resistant material for all paint wetted parts Each with solenoid operated air valves One Graco model # glass bead gun Smooth surfaced deflector to assure full line coverage Minimum three adjustment tips for bead guns to assure proper operation and set up of the unit in varied conditions (one complete set per gun) 9.2. Complete with controls and plumbing 9.3. Mounted on carriage

5 Page 5 of Heat System, single color (requires one transfer pump) degrees F sustainable paint temperature, 50 degree F ambient Boiler: ,000 BTU/hr burner Horizontal tubular liquid heater Fired by a gun type burner Adjustable combustion heat assembly Permits regulation of air into the burner Operation with zero to a trace of smoke Insensitive to draft or back pressure variation Highly resistant to the pulsation Safety controls to prevent overheating, excessive water pressure and shut down in case of malfunction Auto shut down upon glycol preset overtemperature Fuel shut-off solenoid Fuel provided from secondary plastic tank volt DC centrifugal pump for glycol circulation Hoses sized for one pump utilization for maintenance minimization Flow sense switch to shut down burner if glycol circulation stops Heat exchanger (one) Four pass shell and tube type stainless steel Minimum 34 square feet exchange area Automatic diverter valve for glycol to bypass the exchanger for paint temperature control Mounted vertically to facilitate draining Insulated bag with drawstring around each exchanger Temperature controls Two phase automatic control to prevent overheating and optimum paint temperature First phase controls high and low temperature of glycol by cycling burner on and off as it reaches maximum or minimum preset temperature Second phase controls glycol flow into the heat exchanger (by diverter valve) thus paint temperature control Temperature operator interface located on the operator control console within easy reach during operation. One for each system: glycol, paint On / off toggle switch Temperature set knob Analog type temperature control gauges, ten degree increments degree F to 200 degree F range for paint degree F to 260 degree F range for glycol Heating indicator light, To Temp indicator light Vertical glycol expansion tank for fill and/or check level " diameter, 24" high Bolted to the platform Port for checking fluid level psi pressure cap Overflow tube from the cap neck down through the platform

6 Page 6 of Heat System, dual color (requires two transfer pumps and second high pressure pump) degrees F sustainable paint temperature, 50 degree F ambient Boiler: ,000 BTU/hr burner Horizontal tubular liquid heater Fired by a gun type burner Adjustable combustion heat assembly Permits regulation of air into the burner Operation with zero to a trace of smoke Insensitive to draft or back pressure variation Highly resistant to the pulsation Safety controls to prevent overheating, excessive water pressure and shut down in case of malfunction Auto shut down upon glycol preset overtemperature Fuel shut-off solenoid Fuel provided from secondary plastic tank volt DC centrifugal pump for glycol circulation Hoses sized for one pump utilization for maintenance minimization Flow sense switch to shut down burner if glycol circulation stops Heat exchanger (two) Four pass shell and tube type stainless steel Minimum 34 square feet exchange area Automatic diverter valve for glycol to bypass the exchanger for paint temperature control Mounted vertically to facilitate draining Insulated bag with drawstring around each exchanger Temperature controls Two phase automatic control to prevent overheating and optimum paint temperature First phase controls high and low temperature of glycol by cycling burner on and off as it reaches maximum or minimum preset temperature Second phase controls glycol flow into the heat exchanger (by diverter valve) thus paint temperature control Temperature operator interface located on the operator control console within easy reach during operation. One for each system: glycol, paint1, paint On / off toggle switch Temperature set knob Analog type temperature control gauges, ten degree increments degree F to 200 degree F range for paint degree F to 260 degree F range for glycol Heating indicator light, To Temp indicator light

7 Page 7 of Vertical glycol expansion tank for fill and/or check level " diameter, 24" high Bolted to the platform Port for checking fluid level psi pressure cap Overflow tube from the cap neck down through the platform 12. High-pressure piston paint pump (requires 24 hp engine minimum) gpm paint psi Ratio of paint system to hydraulic system is 1: Other ratios not acceptable Waterbase paint compatible, tungsten carbide seats and check balls Packings are spring loaded and self-adjusting Accumulator on discharge side of pump for constant flow and minimal hourglassing Nitrogen charged Y type strainer between pump and guns Plumbed and valved for cleaning Location in an area that is readily accessible for cleaning NPT with 30 mesh element 13. Paint handgun Graco # handgun hose Connection point and valve provided 14. Paint Storage Reservoir, 60 Gallon Unpressurized stainless steel tank Coated, non stainless steel not acceptable maximum diameter each Stainless steel covers Bolted to tank threaded cap for inspection Agitator mount Air vent Teflon gasket seal Minimum 4 of air space above paint at rated capacity Constructed of 11-gauge material Reinforced sides to prevent bulging while full Paint shut off valve at tank outlet, bottom Drain located at lowest point in tank 15. Paint Storage Reservoirs, 60 Gallon/60Gallon Unpressurized stainless steel tanks Coated, non stainless steel not acceptable maximum diameter each

8 15.3. Stainless steel covers Bolted to tank threaded cap for inspection Agitator mount Air vent Teflon gasket seal Minimum 4 of air space above paint at rated capacity Constructed of 11-gauge material Reinforced sides to prevent bulging while full Paint shut off valve at tank outlet, bottom Drain located at lowest point in tank Page 8 of Rear Bumper / Drop Platform Drop platform for cone storage / retrieval wide and extend across the platform back above the road surface gauge safety tread plate Midback high seat with fore and aft adjuster Hand rails 17. Rotating Beacon Amber beacon Located on canopy front, center 18. Second Cover Assembly / Drum Hold Down Stainless steel construction Includes pickup tube and strainer Agitator mount inspection port Allows for pump to draw from either or both barrels 19. Second high-pressure piston paint pump (max of three guns can be run at any time) Hydraulic powered, capable of meeting the performance characteristics required Minimum 8.3 gpm paint psi Ratio of paint pressure to hydraulic pressure 1: All other ratios unacceptable Stainless steel, tungsten carbide seats, for all paint-wetted parts Nitrogen charged accumulator on discharge of high pressure pump for constant flow and minimal hourglassing mesh stainless steel screen strainer between pump and guns 20. Spare tire Extra tire/wheel assembly Shipped loose with unit

9 21. Strobe Light Amber strobe light Located on canopy front, center Page 9 of Transfer pump One 1-1/2 diaphragm loading pump Air operated, non-stalling Transfer paint from supply drums at ground level, to paint tanks Equipped with Teflon balls and Teflon diaphragms Automatic and adjustable inline oiler for pump air supply line if recommended by the pump manufacturer Stainless steel for all paint-wetted parts For tank fill: 12' x 1 ½ " diameter multi-chemical suction hose with basket strainer on one end and a stainless steel coupler with plug on the other 23. Windshield Mounted in front of operator W x 49.5 H Single windshield wiper 24. Work Lights Maximum two work / flood lights Mounted on canopy Facing either platform or carriages Customer to provide preference prior to design