Tube Cleaners Introduction
|
|
- Chrystal Warren
- 6 years ago
- Views:
Transcription
1 Tube Cleaners Introduction Clean tubes mean lower fuel costs. All piping, heat echangers, condensers, chillers, and boiler tubes accumulate scale over various periods of use. This scale decreases flow and retards heat transfer. This consequently increases fuel consumption which lowers overall efficiency. Scale 1/50 in. thick, approimately 5% additonal fuel required. Scale 1/25 in. thick, approimately 10% additional fuel required. Scale 1/16 in. thick, approimately 15% additional fuel required. a boiler tube showing etra fuel required due to scale of various thicknesses. Scale 1/8 in. thick, approimately 30% additional fuel required. Scale 1/4 in. thick, approimately 66% additional fuel required. Scale 1/2 in. thick, approimately 150% additional fuel required. 1/2 inch scale in 6 inch pipe, 1000 feet long, has a transfer capacity loss of 150 gallons per minute. For selecting the proper Airetool tube cleaner components the following information is required: Tube ID Tube length Type of deposit Thickness of deposit Straight or curved tube If curved, the minimum bend radius (see charts) Rigid shaft cleaning systems for straight tubes in heat echangers and condensers are shown on pages Fleible shaft cleaning systems for straight and curves tubes in condensers, chillers, evaporators and other tubular heat transfer apparatus are shown on pages Refer to the overview of motors and cleaning heads based on tube scale thickness and composition on pages 92 (straight tubes) and 93 (curved tubes), then use the selection guide on pages 9497 that match boiler tube cleaning motors and heads together. Note: Operating hoses are not included with boiler tube cleaners. It is always recommended to use an inline lubricator and foot valve when operating the Airetool boiler tube cleaners. See page 117 for more information on these accessories. Boiler tube cleaner applications include: Oil field drill pipe renewal Natural gas line renewal Aluminum smelter siphon tube cleaning Catalyst cleaners Process line cleaning Sugar Refinery Transfer line cleaning 84 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
2 Tube Cleaners Heat Echanger & Condenser Cleaning Systems System Components Motors cc475 & cc475ps cc3751 cc3251 cc325hp Shafts drive coupling drive shaft shaft coupling Drills and Brushes driven shaft ct drill tw drill at drill cb drill spiral brush Complete Cleaning Systems Complete cleaners consist of an air motor with integral water feed valve couplings; up to 22 ft. of shafting with necessary couplings (please specify shaft length required); motor shaft wrench and an etra set of motor blades. The CC 475 Cleaner Complete includes two drills of any type or size up to, three spiral brushes up to and 15 feet of 3/8 inch water hose. The CC 475PS Cleaner Complete includes two drills of any type or size up to 11/2", three spiral brushes up to 11/2" and 15 feet of 3/8 inch water hose. CC3751, 3251 & 325HP: Includes Ball bearing trolley and rope block. Model Order Lightweight Condenser Cleaners Complete CC CC475PS Geared Drive Cleaners Complete CC3751 CC CC325HP PT 15 feet of 3/8 inch Water Hose Water Hose Water Feed Attachment WF mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
3 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Cleaning Motors Clean Tubes Equal Higher Operating Efficiencies Airetool lightweight condenser & geared drive cleaners make it easy to maintain your industrial process at a high level of efficiency by providing cleaning motors that are both powerful and durable. Model Order Range.5 RPM Weight Length Air Inlet Operating Air Pressure Water Inlet Ma. Water Pressure lbs. Kg in. mm NPT PSI kg/cm2 NPT PSI kg/cm2 Lightweight Condenser Cleaners CC up to 1 in. (25.4 mm) ID Tubes / / / CC475PS up to 11/2 in. (38.1 mm) ID Tubes / / / Geared Drive Cleaners* CC up to 13/4 in. (44.4 mm) ID Tubes / CC up to 2 in. (50.8 mm) ID Tubes / CC325HP up to 2 in. (50.8 mm) ID Tubes / * Water hose not included. 86 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
4 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Shaft Components Shafting components connect the motor to the drill head or brush. Drive Shafts & Driven Shafts come in standard lengths of five and ten foot Other lengths available on request drive coupling drive shaft shaft coupling driven shaft Tube I.D. Shaft Drive Drive Drive Shaft Driven Shaft Diameter For Drive For Drive Length* Drive CC475 CC3751 Shaft Shaft Shaft Length* CC475PS Thread CC3251 Thread Thread in. mm in. mm 5 ft. 10 ft. Thread 5 ft. 10 ft. & WF100 & CC325HP / / / / / / / * Stand ial lengths available upon request AT337A ( ) AT333A ( ) AT321A ( ) AT313A ( ) AT309A ( PT) AT301A ( ) AT317A ( ) AT325A ( ) NF NF NF NF NF NF NF 7/16" NF NF 1/2" NF NF NF NF NF NF NF AT333 ( ) AT352 ( ) AT353 ( ) AT359 ( ) AT351 ( ) AT357 ( ) AT354 ( ) NF NF NF NF NF 7/16" NF NF 1/2" NF NF NF NF NF NF NF CC3365 ( ) CC3325 ( ) CC3245 ( ) CC3165 ( ) CC3125 ( ) CC3045 ( ) CC3205 ( ) CC3285 ( ) CC33610 ( ) CC33210 ( ) CC32410 ( ) CC31610 ( ) CC31210 ( ) CC30410 ( ) CC32010 ( ) CC32810 ( ) NFM 1032 F NFM NFF NFM NFF 7/16" NFM NFF 1/2" NFM NFF NFM NFF NFM 7/16" NFF NFM 7/16" NFF CC334 ( ) CC330 ( ) CC322 ( ) CC314 ( ) CC310 ( ) CC302 ( ) CC318 ( ) CC326 ( ) 1032M CC3355 ( ) NFM CC3315 ( ) NFM CC3235 ( ) NFM CC3155 ( ) NFM CC3115 ( ) NFM CC3035 ( ) 7/16" NFM CC3195 ( ) 7/16" NFM CC3275 ( ) CC33510 ( ) CC33110 ( ) CC32310 ( ) CC31510 ( ) CC31110 ( ) CC30310 ( ) CC31910 ( ) CC32710 ( ) Driven Shaft Thread 1032 F 1032 F NFF NFF NFF NFF NFF NFF 3/.8" NFF NFF 3/.8" NFF NFF 7/16" NFF 7/16" NFF 7/16" NFF 7/16" NFF mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
5 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Drills and Brushes Airetool drills are designed especially to prevent damage to the tube I.D., and are available in a variety of shapes to remove all types of scale deposits. Passages in the drill shaft enable flushing fluid to reach the drill cutting edge. Larger sizes available on request. Type AT standard drill for medium deposits Type CB standard drill ( AT style) for medium deposits with carbide insert for better durability Type CBHP high pressure drills provide better flushing power when used with the CC325HP motor Type TW standard twist drill for thick deposits Type CT standard twist drill ( TW style) for thick deposits with carbide insert for better durability Wire Brushes are for light deposits Minimum order quantities may apply. Tube I.D. Diameter of AT CB CB (Carbide) CT Drill or Brush Stud (Standard) Drills (Carbide) Drills HP Drills* (Carbide Twist) TW Wire Thread Drills (Twist) Drills Brush in. mm in. mm Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) UNC UNC UNC UNC UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF AT199 ( ) AT1995 ( ) AT200 ( ) AT2005 ( ) AT201 ( ) AT202 ( ) AT203 ( ) AT204 ( ) AT205 ( ) AT206 ( ) AT207 ( ) AT208 ( ) AT108 ( ) AT209 ( ) AT210 ( ) AT211 ( ) AT212 ( ) * HP Style drills are used for more aggressive cleaning with CC325HP cleaning motor CB199 ( ) CB1995 ( ) CB200 ( ) CB2005 ( ) CB201 ( ) CB202 ( ) CB203 ( ) CB204 ( ) CB205 ( ) CB206 ( ) CB207 ( ) CB208 ( ) CB108 ( ) CB209 ( ) CB210 ( ) CB211 ( ) CB212 ( ) CB205HP ( ) CB206HP ( ) CB207HP ( ) CB208HP ( ) CB108HP ( PT) CB209HP ( ) CB210HP ( ) CB211HP ( ) CB212HP ( PT) CT205 ( ) CT206 ( ) CT207 ( ) CT208 ( ) CT108 ( ) CT209 ( ) CT210 ( ) CT211 ( ) CT212 ( ) TW201 ( PT) TW202 ( ) TW203 ( ) TW204 ( ) TW205 ( ) TW206 ( ) TW207 ( ) TW208 ( ) TW108 ( ) TW209 ( ) TW210 ( PT) TW211 ( ) TW212 ( ) 199B ( ) 1995B ( ) 200B ( ) 2005B ( ) 201B ( ) 202B ( ) 203B ( PT) 204B ( ) 205B ( ) 206B ( ) 207B ( ) 208B ( ) 108B ( ) 209B ( ) 210B ( ) 211B ( ) 212B ( ) 88 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
6 Tube Cleaners Heat Echanger & Condenser Cleaning Systems Drills and Brushes (continued) Tube I.D. Diameter of AT CB CB (Carbide) CT Drill or Brush Stud (Standard) Drills (Carbide) Drills HP Drills* (Carbide Twist) TW Wire Thread Drills (Twist) Drills Brush in. mm in. mm Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) Model (Order No.) UNF UNF UNF UNF UNF UNF UNF UNF UNF UNF /16" UNF /16" UNF /16" UNF /16" UNF /16" UNF /16" UNF /16" UNF AT213 ( ) AT214 ( ) AT215 ( ) AT216 ( ) AT217 ( ) AT218 ( ) AT219 ( ) AT220 ( ) AT221 ( ) AT222 ( ) AT223 ( ) AT224 ( ) AT225 ( ) AT226 ( ) AT227 ( ) AT228 ( ) AT229 ( ) * HP Style drills are used for more aggressive cleaning with CC325HP cleaning motor CB213 ( ) CB214 ( ) CB215 ( ) CB216 ( ) CB217 ( ) CB218 ( ) CB219 ( ) CB220 ( ) CB221 ( ) CB222 ( ) CB223 ( PT) CB224 ( PT) CB225 ( ) CB226 ( ) CB227 ( ) CB228 ( ) CB229 ( ) CB213HP ( PT) CB214HP ( ) CB215HP ( ) CB216HP ( ) CB217HP ( ) CB218HP ( ) CB219HP ( PT) CB220HP ( PT) CB221HP ( ) CB222HP ( ) CT213 ( ) CT214 ( ) CT215 ( ) CT216 ( ) CT217 ( PT) CT218 ( ) CT219 ( ) CT220 ( ) CT221 ( PT) CT222 ( PT) CT223 ( ) CT224 ( ) CT225 ( ) CT226 ( ) CT227 ( ) CT228 ( ) CT229 ( ) TW213 ( ) TW214 ( ) TW215 ( ) TW216 ( ) TW217 ( ) TW218 ( ) TW219 ( ) TW220 ( ) TW221 ( ) TW222 ( ) TW223 ( ) TW224 ( ) TW225 ( ) TW226 ( ) TW227 ( ) TW228 ( ) TW229 ( ) 213B ( ) 214B ( ) 215B ( ) 216B ( ) 217B ( ) 218B ( ) 219B ( ) 220B ( ) 221B ( ) 222B ( ) 223B ( ) 224B ( ) 225B ( ) 226B ( PT) 227B ( ) 228B ( ) 229B ( ) Large Diameter Twist Brushes (LDTB) Brush should be sized 1/8" 3/16" smaller than the nominal tube I.D. for best results. in. Diameter mm Model Order Stud Thread LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB PT 5/8 NC LDTB /8 NC LDTB PT 5/8 NC LDTB PT 5/8 NC in. Diameter mm Model Order Stud Thread LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC LDTB /8 NC mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
7 Condenser Cleaners Tube Cleaners Tube cleaners for condensers, chillers, evaporators and other tubular heat transfer apparatus Model ABM1800 Variable speed feature allows the operator to operate the shaft at a safe, comfortable speed for the condition of the tubes being cleaned. The lack of orings and coupler nut eliminates the risk of the coupler nut loosening and leaking water, leading to possible shaft damage. Variable solid state speed control from 0 to 1750 RPM with constant torque Quickrelease shaft coupling for an easy, fast, positive connection every time No orings or coupler nut Model ABM1900 Variable solid state speed control from 0 to 1750 RPM with constant torque Manifold for screwon style shafting that is commonly used in competitive models Reversible Models ABM1800R & ABM1900R Same features as ABM1800 & ABM1900 above plus Bidirectional shaft rotation for the cleaning of internally enhanced tubes Identified Forward and Reverse direction foot pedals are included abm1900 abm1800r Model Ordering Horsepower Volts Amps RPM Bidirectional Operation Dimensions Weight (less shaft) Shipping Dimensions Shipping Weight (less shaft) ABM / No 1 W 17" L 9" H 35 lbs. 12" W 23" L 1H 39 lbs. ABM1800R / Yes 1 W 17" L 9" H 41 lbs. 12" W 23" L 1H 45 lbs. ABM / No 1 W 17" L 9" H 35 lbs. 12" W 23" L 1H 39 lbs. ABM1900R / Yes 1 W 17" L 9" H 41 lbs. 12" W 23" L 1H 45 lbs. ABM1900R230V* / Yes 1 W 17" L 9" H 41 lbs. 12" W 23" L 1 H 45 lbs. *CE Certified Fleible shafts (sold separately) To order the correct size Fleible Shaft, measure the tube I.D. and the length of the tube to be cleaned. Then refer to the chart at the right to select the proper shaft. Tube I.D. Range Shaft O.D. Shaft Lengths in Feet Model No. (Ordering No.) Fleible Shafts for ABM1800, ABM1800R and ABM ".406 FS18151/4 ( ).407".532" FS18253/8 ( ) FS18353/8 ( ).533".812" 1/2" FS18251/2 ( ) FS18351/2 ( ) Fleible Shafts for ABM1900 and ABM1900R.280".406 FS19151/4 ( ).407".532" FS19253/8 ( ) FS19353/8 ( ).533".812" 1/2" FS19251/2 ( ) FS19351/2 ( ) See net page for brush selection. 90 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
8 Condenser Cleaners BrushMaster Tube Cleaners SCB750 Brushmaster Brushes Super 2D Brushes Airetool Super 2D Brushes are for cleaning internally enhanced tubing. The brush is constructed from material that out cleans and out wears other tube brushes. Super 2 D Brushes have two cleaning diameters to assure all surfaces are being cleaned. These brushes are recommended for removing soft and light scale deposits. SB1000 Super Brushes Super Brushes are for cleaning smooth bore tubing. They are made from the same longlasting material as the Super 2D Brush. The longer brush cleaning surface reduces the tube cleaning time. They are recommended for removing soft and light scale deposits. N625 Part Order in. Tube Inside Diameter mm B625 Super 2 D Brush SCB SCB Super Brush SB SB SB Nylon, Brass and Stainless Steel Brushes Nylon, brass and stainless steel brushes are available in brush diameters.250" 1.000" ( mm) in 1/16" (1.6mm) increments. Select the brush size equal to or one size smaller than the I.D. of the tubes to be cleaned. Minimum order quantity 12 pieces Brush Diameter Brush Material in. mm Nylon Brass Stainless Steel 1/ N250 ( ) B250 ( ) SS250 ( ) 5/ N312 ( ) B312 ( ) SS312 ( ) 3/ N375 ( ) B375 ( ) SS375 ( ) 7/ N437 ( ) B437 ( ) SS437 ( ) 1/ N500 ( ) B500 ( ) SS500 ( ) 9/ N562 ( ) B562 ( ) SS562 ( ) 5/ N625 ( ) B625 ( ) SS625 ( ) 11/ N687 ( ) B687 ( ) SS687 ( ) 3/ N750 ( ) B750 ( ) SS ) 13/ N812 ( ) B812 ( ) SS812 ( ) 7/ N875 ( ) B875 ( ) SS875 ( ) 15/ N937 ( ) B937 ( ) SS937 ( ) N1000 ( ) B1000 ( ) SS1000 ( ) mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
9 Boiler Tube Cleaners Tube Cleaners for Straight Tubes Complete series of motors and heads available for tube sizes 1/2" to 1 (12.7 to 34.9 mm) I.D. Drill with Universal Joint Range: 1/2 in. (12.7 mm) 13/8 in. (34.9 mm) Deposit: heavymedium to soft Midget Motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; metal bo; choice of single unit cutter head with four etra cutters and two etra cutter pins. If a Type 2 head (30 series) is ordered, one etra fleible connection is furnished. If epanding blade head is ordered, one etra set of blades is furnished. For operating hose (not included) refer to page 116. Single Unit with Universal Joint Range: 1/2 in. (12.7 mm) 13/8 in. (34.9 mm) Deposit: lighthard to medium Epanding Blade Cutter Range: 1/2 in. (12.7 mm) 41/2 in. (114.3 mm) Deposit: lighthard to medium Complete series of motors and heads available for tube sizes 11/2" to 13 (12.7 to 336.5mm) I.D. Type4 Forward Swing Range: 13/4 in. (44.4 mm) 4 1/4 in. (120.6 mm) Self feeding Deposit: 1/2 in. (12.7 mm) thicksoft to medium Type5 Wing Arm Range: 13/4 in. (44.4 mm) 13 1/4 in. (336.5 mm) Self feeding Deposit: 1/2 in. (12.7 mm) thickhard to medium 3000 Series Motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; choice of cutter head with two etra sets of cutters and cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra sets of cutters are furnished. If armtype head is ordered, one etra set of arm pins is furnished. For operating hose (not included) refer to page 116. Type3 PType Range: 21/4 in. (57.1 mm) 7 in. (177.8 mm) Self feeding Deposit: 3/8 in. (9.5 mm) thickhard to medium Drill with Universal Joint Range: 11/2 in. (38.1 mm) 11 in. (279.4 mm) Deposit: 3/4 in. (19.0 mm) thickmedium to hard and plugged tubes 92 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
10 Boiler Tube Cleaners Tube Cleaners for Curved Tubes Complete series of motors and heads available for tube sizes 13/16" to 21/8" (20.6 to 53.9 mm) I.D. Drill with Universal Joint Range: 11/2 in. (38.1 mm) 21/8 in. (53.9 mm) Deposit: lighthard to medium midget motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; metal bo; choice of single unit cutter head with four etra cutters and two etra cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra cutters are furnished. For operating hose (not included) refer to page 116. Type1 40" Series Single Unit with Universal Joint Range: 1/2 in. (12.7 mm) 21/8 in. (53.9 mm) Deposit: lightmedium to hard Type2 30" Series Single Unit with Fleible Shaft Range: 1/2 in. (12.7 mm) 21/8 in. (53.9 mm) Deposit: lightmedium to hard Complete series of motors and heads available for tube sizes 11/2" to 13 (38.1 to mm) I.D. Drill with Universal Joint Range: 11/2 in. (38.1 mm) 11 in. (279.4 mm) Deposit: 1/2 in. (12.7 mm) thickhard to medium 4000 series motor with optional heads Complete cleaner consists of: air motor with etra set of blades; shaft wrench; choice of cutter head with two etra sets of cutters and cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra sets of cutters are furnished. If armtype head is ordered, one etra set of arm pins is furnished. For operating hose (not included) refer to page 116. Type4 Forward Swing with Universal Joint Range: 13/4 in. (44.4 mm) 43/4 in. (120.6 mm) Deposit: 1/2 in. (12.7 mm) thicksoft to medium Type5 Wing Arm with Universal Joint Range: 13/4 in. (44.4 mm) 131/4 in. (336.5 mm) Self feeding Deposit: 1/2 in. (12.7 mm) thickhard to medium mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
11 Boiler Tube Cleaners Selection Guide Midget Tube Cleaners Curved and Straight Range: 1/2 to 13/4 in to 44.4 mm Complete cleaner consists of: air motor with etra set of blades; shaft wrench; metal bo; choice of single unit cutter head with four etra cutters and two etra cutter pins. If a Type 2 head (30 series) is ordered, one etra fleible connection is furnished. If epanding blade head is ordered, one etra set of blades is furnished. For operating hose (not included) refer to page 116. midget motor Tube I.D. Minimum Tube Centerline Radius Motor Motor O.D. Rotor Air Thread Hose Size Pipe Tap in. mm in. mm in. mm in. (in.) in. mm Universal Type 1 s Available Fleible Type 2 Blade Type 8 Use for straight tubes. Use for curved tubes. Drill* Universal Fleible 1/ Straight 24 15/ / MD / Straight 30 37/ /4 NF 1/8 1/ MD2 PA3051 X6461 3/ Straight 27 11/ /4 NF 1/8 1/ MD3 PA3051 X / X64 11/ /4 NF 1/4 1/4 6.3 X6440 X6430 MD X6461 7/ Straight 29 25/ /8 NF 1/4 3/ MD4 2651A 27/ Straight 29 25/ /8 NF 1/4 3/ MD4 2651A Straight 26 29/ /8 NF 3/8 3/ MD4 2651A 11/ X61 7/ /16 NF 1/4 1/4 6.3 X6140 X6130 MD3 6151C X / Straight 31 11/ /16 NF 3/8 3/ MD X / Straight X63A 11/ /8 NF 3/8 3/8 9.5 X6340 X MD X / X63 11/ /8 NF 3/8 3/8 9.5 X6340 X6330 MD X / Straight X65A 13/ /8 NF 3/8 3/8 9.5 X6540 X X / X65 13/ /8 NF 3/8 3/8 9.5 X6540 X6530 MD X / / /8 NC 1/2 1/ / X66 15/ /8 NF 3/8 3/8 9.5 X6640 X X / / /8 NC 1/2 1/ Some items are available on a quotation basis only. * Drill must be used with Universal Joint or fleible connection. 94 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
12 Boiler Tube Cleaners Selection Guide 3000 and 4000 Series Tube Cleaners Curved and Straight Range: 11/2 to 131/4 in to mm Complete cleaner consists of: air motor with etra set of blades; shaft wrench; choice of cutter head with two etra sets of cutters and cutter pins; universal joint with two etra pins; two drills. If single unit head is ordered, four etra sets of cutters are furnished. If armtype head is ordered, an etra set of arm pins is furnished. For operating hose (not included) refer to page 116. Use for straight tubes. Use for curved tubes. Tube I.D. Minimum Tube Centerline Radius Motor Motor O.D. Rotor Air s Available Thread Hose Size Single Forward Single Unit Pipe Tap Epansion Swing in. mm in. mm in. mm in. (in.) in. mm Type 3 Type 4 Type 2 Type 1 Universal Joint Drill* 11/ Straight / /16 NC 1/2 1/ TC / Straight / /8 NC 3/4 1/ TC / Straight / /8 NC 3/4 1/ TC / Straight / /8 NC 3/4 3/ TC17PY Straight / /8 NC 3/4 3/ TC / /8 NC 1/2 1/ / Straight /8 NC 3/4 3/ TC13PY / / /8 NC 1/2 1/ / Straight / /4 NC 3/4 3/ P15PY 4470A / / /8 NC 1/2 1/ / / /8 NC 1/2 1/ / Straight / /4 NC P9S 4470A / Straight / /8 NC P9 4470B / / /8 NC 1/2 1/ Some items are available on a quotation basis only. * Drill must be used with Universal Joint or fleible connection. mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
13 Boiler Tube Cleaners Selection Guide Tube I.D. Minimum Tube Centerline Radius Motor Motor O.D. Rotor Air Thread Hose Size Pipe Tap in. mm in. mm in. mm in. (in.) in. mm Single Epansion Type 3 s Available Wing Arm Type 5 25/ Straight / /8 NC P A / / /4 NC 1 3/ / Straight / /8 NC P A / / /4 NC 1 3/ / Straight / /8 NC P6A / / /4 NC 1 3/ Straight / NF P / /4 NC 1 3/ / /4 NC 1 3/ / Straight / NF P / Straight / NF P / Straight NF P / Straight NF P / / /8 NC B / Straight NF P Straight / /8 NF P / / /8 NC B / Straight / /8 NF P / Straight / /8 NF P / Straight / /8 NF P Straight / /8 NF P / /8 NC B / Straight / /8 NF P / Straight / /8 NF P1 5060AS / / /8 NC B / Straight / /8 NF P1 5060AS / Straight / /8 NF P0 5060AS / / /8 NC B / / /8 NC B / Straight / /8 NF P AS / / /8 NF A Straight / /8 NF 11/4 11/ TC19HS E / /8 NF 1 11/ TC19HS Some items are available on a quotation basis only. * Drill must be used with Universal Joint or fleible connection. Forward Swing Type 4 Universal Joint Drill* 96 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
14 3000 Series Motors 3000 Series Motors 3000 series straight motors, components and (ordering numbers) All Motors include Shaft Wrench Motor Motor O.D. Tube I.D. Case Cylinder Rear Machine Rotor Blades (Qty.) Thrust Plate Front Bearing Rear Bearing Rear Cap Front Dowel Rear Dowel Shaft Wrench Rotor Hose Thread Size 3150 ( ) 3162 ( ) 3175 ( ) 3187 (407600) 3200 ( ) 3212 ( ) 3225 ( ) 3250 ( ) 3262 ( ) 3275 ( ) 1 11/2" 11/2" " 2" 21/8" 21/8" /2" 21/2" ( ) 213/16" 3" 3318 ( ) 3350 ( ) 3400 ( ) 3500 ( ) 3600 ( ) 3" 33/16" " 4 5" 5 6" ( ) ( ) ( ) ( ) ( PT) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( PT)( PT) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( PT) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 1806 (4) ( PT) 1806 (4) ( PT) 1806 (4) ( PT) 2306 (4) ( ) 2306 (4) ( ) (4) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) 1707 ( ) 1807 ( ) 1807 ( ) C ( ) 2307 ( ) ( ) 1507 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) Motors for tube/pipe sizes larger than 5" ID are supplied with ribs or rib cage to center the motor in tube or pipe being cleaned. X 1708 ( ) X 1808 ( PT) X 1808 ( PT) 2208 ( ) 2208 ( ) 2208 ( ) 1408 ( ) ( ) 1008 ( ) 1008 ( ) 1108 ( ) 1108 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 3213 ( ) 4413 ( ) 3213 ( ) 3213 ( ) 213 ( PT) 213 ( PT) 713 ( ) 713 ( ) 713 ( ) 713 ( ) 713 ( ) 713 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 9/16" (140809) (140810) (140810) (140810) (140810) (140810) (140812) (140814) (140814) (140814) ( ) ( ) 9/16" 11/8" 11/8" ( ) 11/8" 11/8" ( ) 1 1 ( ) 1 1 ( ) 1/2" 1/2" 1/2" 1 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
15 4000 Series Motors 4000 Series Motors 4000 series motors, components and (ordering numbers) Motor 4250 ( ) 4300 ( ) 4325 ( ) 4350 ( ) 4450 ( ) 4481 ( ) 4600 ( ) Motor O.D. Tube I.D. Case Cylinder Rear Machine Rotor Blades (Qty.) Thrust Plate 21/4 X 15R 1 215/16 X 12R (4) /2 X 15R ( ) ( ) ( ) ( ) ( ) ( ) ( ) 2 25/8 X 24R (5) /4 X 12R ( ) ( ) ( ) ( ) ( ) ( ) ( ) 21/2" 2 27/8 X 28R 3 X 16R 31/4 X 16R 31/2 X 20R 31/8" 4 X 15R (5) 3207 ( ) ( ) ( ) ( ) ( ) ( ) ( ) (5) 3307 ( ) ( ) ( ) ( ) ( ) ( ) ( ) Front Bearing 4408 ( ) 3308 ( ) 3308 ( ) 3708 ( ) Rear Bearing ( ) ( ) ( ) (5) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( PT) ( ) 3 413/16 X 18R (5) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 5" 53/4 X 72R 6 X 26R *Includes Machine Motors are supplied with ribs or rib cage for tube/pipe sizes larger than 6" ID (5) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 5008 ( ) 5008 ( ) Rear Cap 4413 ( ) 3213 ( ) 3213 ( ) Front Dowel Rear Dowel ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( PT) ( ) ( ) ( ) ( ) 713 ( ) 713 ( ) 713 ( ) ( ) ( ) ( ) ( ) ( ) ( ) Tail Hose Assembly* Line A Below Line B Below Line B Below Line B Below Line B Below Not Req d Not Req d Shaft Wrench (140810) (140812) (140812) (140814) (140814) Rotor Thread 11/8" ( ) 11/8" 11/8" ( ) 11/8" Hose Size 1/2" Line Tap Size A 1/2" B Tail Hose 4415 ( ) 3315 ( ) Hose 4116 ( ) 3316 ( PT) Clip Screw Ferrule ) 3318 ( ) 4418 ( ) Accessory Heavy Duty Screw Type Tail Hose Assemblies with Wire Inserted Hose and Spring Protector for 4000 Series Motors Tail Hose Assembly HD ( ) HD ( ) HD ( ) HD ( ) HD ( ) HD ( ) Used With Motor Assembly Machine Hose Hose Pipe Tap Compression Nut Compression Ferrule Compression Sleeve Detail # Qty. Required KB ( ) B ( ) KB ( ) B ( ) B ( ) B ( ) ( ) ( ) ( ) ( PT) ( PT) ( ) 1/2" C ( ) C ( ) C ( ) C ( ) C ( ) C ( ) D ( ) D ( ) D ( ) D ( ) D ( ) D ( ) E ( ) E ( ) E ( ) E ( ) E ( ) E ( ) Hose ( ) K ( ) K ( ) K ( ) K ( ) K ( ) Spring ( ) K ( ) K ( ) K ( ) K ( ) K ( ) 98 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
16 60 Series & 4000 Series Motors 60 & 4000 Series Motors 60 & 4000 series motors, components and (ordering numbers) Motor Motor O.D. Tube I.D. (Radius) Case Rear w/ Bearing Machine Rotor Blades (4 req.) Rear Bearing Rear Dowel (Qty.) Tail Hose Tail Hose Tail hose Assembly Front Ferrule Rear Ferrule Shaft Wrench Rotor Thread Hose Size X 64 ( ) 11/16" X 61 ( ) X 63 ( ) 11/16" X 65 ( ) 13/16" X 66 ( ) ( ) 4225 ( ) 11/2" 1 13/16" (5") 11/32" (5") 1 (6") 11/2" (6") 1 (6") 1 (24") 1 (15") 2" (15") X 6401 ( ) X 6101 ( ) X 6301 ( ) X 6501 ( PT) X 6601 ( ) G ( ) G ( ) X 6403 ( ) X 6103 ( ) X 6303 ( ) X 6503 ( ) X 6603 ( ) ( ) ( ) X 6404 ( ) X 6104 ( ) X 6304 ( ) X 6504 ( ) X 6604 ( ) ( ) ( ) X 6405 ( ) X 6105 ( ) X 6305 ( ) X 6505 ( ) X 6605 ( ) ( ) ( ) X 6406 ( ) X 6106 ( ) X 6306 ( ) X 6506 ( ) X 6606 ( ) 4106 ( ) 4106 ( ) ( ) ( ) X 6412 (2) ( ) X 6112 (2) ( ) X 6312 (2) ( ) X 6312 (2) ( ) X 6312 (2) ( ) ( ) ( ) X 6415 ( ) X 6115 ( ) X 6315 ( ) X 6315 ( ) X 6315 ( ) 4115 ( ) 4115 ( ) X 6416 ( ) X 6116 ( ) X 6316 ( ) X 6316 ( ) X 6316 ( ) 4116 ( ) 4116 ( ) X 6419 X 6417 ( ) X 6119 X 6117 ( PT) X 6319 X 6317 ( ) X 6519 X 6317 ( ) X 6619 X 6617 ( ) ( ) ( ) 1 AJ243 ( ) 1 AJ243 ( ) X 6418 ( ) X 6118 ( ) X 6318 ( ) X 6318 ( ) X 6318 ( ) 1 AJ243 ( ) 1 AJ243 ( ) 3/16" ( ) (140804) (140805) (140805) ( ) (140810) (140810) 1/2" 1/2" mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
17 Midget Motors Midget Motors For 1/2" 1 I.D. tubes Straight tube midget motors, components and (ordering numbers) Motor Motor O.D. Tube I.D. Case Rear Machine Rotor Rotor Blade (Qty.) Dowel pin (Qty.) Shaft Wrench Rotor Thread Air Hose 24 ( ) 15/32" 1/2" X 2401 ( ) 2403 ( ) 2404 ( ) 2405 ( ) 2406 (4) ( ) 2412 ( ) 5/32" ( ) /16" 30 ( ) 37/64" X 3001 ( ) X 3003 ( ) X 3004 ( ) X 2705 ( ) 2706 (4) ( ) 3012 ( ) 3/16" ( ) 27 ( ) 11/16" X 2701 ( ) X 2703 ( ) 2704 ( PT) X 2705 ( ) 2706 (4) ( ) 3012 ( ) 3/16" ( ) 29 A ( ) 25/32" 2901 A ( ) 2903 A ( ) 2904 ( ) 2605 ( PT) 2606 (4) ( ) X 6112 ( ) (140805) 26 ( ) 29/32" 2601 G ( ) 2603 ( ) 2604 ( ) 2605 ( PT) 2606 (4) ( ) X 6312 ( ) (140805) 31 ( ) 11/32" 11/8" 3101 ( ) 3103 ( ) 3104 ( ) 3105 ( ) 3106 (4) ( PT) 3111 ( ) ( ) X 63 A ( ) 11/16" 1 X 6301 ( ) X 6303 ( ) X 6304 A ( ) X 6305 ( ) X 6306 (4) ( ) X 6312 (2) ( ) (140805) X 65 A ( ) 13/16" 1 X 6501 ( PT) X 6503 ( ) X 6504 A ( ) X 6505 ( ) X 6506 (4) ( ) X 6312 (2) ( ) (140805) Water Driven Motors For 2" and 3 I.D. tubes Water driven motors are used only in the overhead cleaning of vertical catalyst tubes. Model Motor O.D. Tube I.D. Case Water Wheel Rear Machine Pipe Tap Shaft Thrust Bearing Front Bearing Rear Thrust Shaft Wrench Shaft Thread Hose W7 ( ) 31/2" 3 W 701 ( ) W 702 ( PT) W 703 ( ) W ( ) 11/2" W 905 ( ) W 907 ( ) W 908 ( ) W 910 ( ) (140814) 11/2" W16A ( ) 111/16" 2" W 1601 A ( ) W 1602 ( ) W 1603 A ( ) W 1604 A ( ) W 1605 ( ) W 1607 ( ) W 1608 ( ) W 1610 ( ) (140810) * Other sizes available. Contact customer service for details 100 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
18 Gas Line Cleaners Gas Line Cleaners Range: 3/4 to 11/2 in to mm Used successfully by gas utilities for cleaning old service lines before inserting new plastic and copper tubing. The thorough cleaning action of the barrelshaped cutter head assures the removal of material that could cut or rupture the renewal tubing. Renews gas service lines instead of replacing them Complete kit consists of: motor, with an etra set of blades; head; lubricator; wire wound hose; spare cutters and a metal carrying case Other sizes available on request Cleaner Complete Order Pipe I.D. Motor Assembly Motor Diameter Assembly Air Inlet Hose Size Hose Length in. mm Model Order No. in. mm Model Order No. in. mm in. mm ft M 27 GLC / / S / / X 64 GLC X / S 1/ / X 61 GLC 50 11/ X / S 1/ / X 63 A GLC / X 63 A / S / / X 63 A GLC / X 63 A / S / / X 65 GLC / X / S / / X 65 A GLC / X 65 A / S 3/ / X 65 A GLC / X 65 A / S 3/ / * Other sizes may be available. Contact customer service for details mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
19 Type 1 Single Unit s 1/2" 2 I.D. Series 40 Single unit heads, components and (ordering numbers) Tube I.D. Universal Joint Shaft Jaw Tap Adapter Cutter Pin Cone Cutter Cylinder Cutter 2440 ( ) 1/2" 2451 ( ) ( ) 2487 S ( ) 3040 ( ) 11/16" PA 3051 ( ) 2734 ( ) 3037 ( ( ) 13/16" PA 3051 ( ) 2734 ( ) C 3 ( ) 2740 S ( PT) 13/16" 6451 ( ) 2944 ( ) 2947 S (2) ( PT) X 6440 ( ) 13/16" 6451 ( ) 2944 ( ) 2947 ( ) 2940 ( ) 27/32" 2651 ( ) 2943 ( ) 2944 ( ) 2947 ( ) 2640 ( ) 2651 ( ) 2643 ( ) 2644 ( ) 337 ( ) X 6140 ( PT) 11/32" 6151 ( PT) 2644 ( ) 337 ( ) 3140 ( ) 11/8" 6651 ( ) 7/16" 3144 A ( ) 2837 ( ) X 6340 ( ) ( ) 2544 S ( ) 947 ( ) ( ) 1 11/2" 3151 ( ) 7/16" 2544 S ( ) 947 ( ) X 6540 ( ) ( ) 2544 S ( ) 6547 ( ) 1740 ( ) 11/2" ( ) 9/16" 1743 ( ) 2844 ( ) 1097 ( ) 1088 ( ) 1940 ( ) ( ) 1943 ( ) 1944 ( ) 797 ( ) 788 ( ) X 6640 ( ) ( ) 2544 S 897 B ( ) ( ) 4140 ( ) 1 2" 4151 ( ) 1943 ( ) 1944 ( ) 897 B ( ) 888 B ( ) 4440 C ( ) ( ) 1943 ( ) 1944 ( ) 897 ( ) 888 ( ) 102 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
20 Type 2 Single Unit s 1/2" 21/8" I.D. Series 30 Single unit heads, components and (ordering numbers) Tube I.D. Fle Connection Shaft Cpl. Tap Cpl. Tap Adapter Cutter Pin Cone Cutter Cylinder Cutter Length Diameter 2430 ( ) 1/2" 2461 A ( ) ( ) 2487 S ( ) 4" 3/16" 3030 ( ) X 6461 A ( ) 2734 ( ) 3037 ( ) 4" 3/16" 2730 ( ) X 6461 A ( ) 2734 ( ) C 3 ( ) 4" 3/16" X 6430 ( ) 13/16" X 6461 A ( ) 2944 ( ) 2947 ( ) 4" 3/16" 2930 ( ) 2961 A ( ) 2943 ( ) 2944 ( ) 2947 ( ) 41/2" A ( ) 2644 ( ) 337 ( ) 41/2" 2630 ( ) 2661 A ( ) 2644 ( ) 337 ( ) 41/2" X 6130 ( ) 11/32" X 6161 A ( ) 2644 ( ) 337 ( ) 4" ( ) 11/8" X 6361 A ( ) 7/16" 3144 A ( ) 2837 ( ) 41/2" X 6330 ( ) 1 X 6361 A ( ) 7/16" 2544 S ( ) 947 ( ) 41/2" X 6530 ( ) 11/2" X 6661 A ( ) 7/16" 2544 S ( ) 6547 ( ) 61/2" X 6630 ( ) 1 X 6661 A ( ) 7/16" 2544 S ( ) 797 ( ) 61/2" 4130 ( ) 1 21/8" 4161 A ( ) 1943 ( ) 1944 ( ) 897 B ( ) 888 B ( ) 7" 1/2" mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
21 Type 3 Single Epansion P & TC s 11/2" 7" I.D. for Straight Tubes and Drill Pipe Single epansion heads, components and (order numbers) PY heads developed specifically for the rigorous conditions found in Pipe Yard applications PY heads have larger diameter front ends and stronger coupling studs that increase durability Tube I.D. Closed Epands To Cage Pin Plate Tap Cutter Pin Cone Cutter Cylinder Cutter TC 14 ( ) TC 11 ( ) TC 17 PY ( ) TC 16 PY ( ) TC 13 PY ( ) P 15 PY ( ) P 9 S ( ) P 9 PY ( ) P 8 ( ) P 7 ( ) P 6 A PY ( ) P 6 P 5 ( ) P 4 ( PT) P 3 ( ) P 2 ( ) P 1 P 0 P 10 ( ) TC 19 H S TC 19 S TC 20 S ( ) TC 21 S TC 22 S TC 23 S TC 24 S 11/2" 1 123/32" 1 1 2" 1 111/16" 2" 2" 113/16" 23/16" 21/8" /16" 27/16" 2 23/16" 211/16" 21/2" 2 213/16" 2 29/16" /16" 21 3" 211/16" 31/8" 31/8" 213/16" /16" 39/16" 31/2" 33/16" 313/16" 3 39/16" 43/16" 4" 3 41/2" 4 313/16" 4 41/2" 41/8" " 41/2" 59/16" " 51/2" 61/2" /2" 6" 71/16" " 61/2" 79/16" 1781 ( ) 1881 ( ) 2281 T C 17 PY ( ) 2381 PY ( ) 2381 A PY ( ) P 1591 PY ( ) P 991 S ( ) P 991 PY ( ) P 891 ( ) P 1592 ( ) P 992 S ( ) P 992 ( ) P 892 ( ) 1783 ( ) 1883 ( ) 2383 ( ) 2383 ( ) 2383 ( ) 183 ( ) 183 ( ) 183 ( ) ( ) P 791 P S ( ) P 691 A PY ( ) P 692 A ( ) P 691 AY P 692 ( ) P 591 ( ) P 491 ( PT) P 391 ( ) P 291 ( ) P 592 ( ) P 492 ( ) P 392 ( ) P 292 ( ) 983 S ( ) 983 S ( ) 983 S ( ) 883 D ( ) 883 F ( ) 883 F ( ) P 191 P F ( ) P 091 ( ) P 1091 ( ) 1991 H S 1991 S 2091 S ( ) 2191 S 2291 S 2391 S 2491 S P 092 ( ) P 1092 ( ) 883 F ( ) 883 F ( ) ( ) 8293 ( ) 8293 ( ) 8293 ( ) 8293 ( ) 8293 ( ) 9/16" 1 1/8" 1 1/8" 1 1/8" (1), 1884 (1) ( ) ( PT) 1584 (1), 1884 (1) ( ) ( PT) 1584 PY (3) ( ) 1584 PY (3) ( ) 1584 PY (3) ( ) 2484 PY (3) ( ) 2484 (3) ( ) 1584 PY (3) ( ) 184 (3) ( ) 184 (3) ( ) 184 PY (3) ( ) 184 (3) ( ) 184 (3) ( ) 884 (3) ( ) 884 (3) ( ) 884 (3) ( ) 884 P (3) ( ) 884 P (3) ( ) 884 P (3) ( ) 884 P (3) ( ) 884 P (4) ( ) 884 P (4) ( ) 884 P (4) ( ) 884 P (4) ( ) 2484 S (4) ( ) 2484 S (4) ( ) 1787 (1) ( ) 1587 (1) ( ) 2287 (3) ( ) 1787 (3) ( ) 1787 (3) ( ) 2487 (3) ( ) C 52 (3) ( PT) 1587 (3) ( ) 1087 (3) ( ) 1087 (3) ( ) 1087 (3) ( ) 1087 (3) ( ) 987 (3) ( ) 787 (3) ( ) 887 B (3) ( ) 887 (3) ( ) 887 (3) ( ) 887 B (3) ( ) 887 (3) ( ) 1287 (3) ( ) 1287 (4) ( ) 1287 (4) ( ) 1788 (2) ( ) 1588 (2) ( ) 2288 (6) ( ) 1788 (6) ( ) 1788 (6) ( ) 2488 (6) ( ) C 76 (6) ( ) 1588 (6) ( ) 1088 (6) ( ) 1088 (6) ( ) 1088 (6) ( ) 1088 (6) ( ) 988 (6) ( PT) 788 (6) ( ) 888 B (6) ( ) 888 (6) ( ) 888 (6) ( ) 888 B (6) ( ) 888 (6) ( ) 1288 (9) ( ) 1288 (12) ( ) 1288 (12) ( ) (4) (12) (4) (12) 8287 (4) 8288 (12) 8287 (4) 8288 (12) 104 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
22 Type 4 Forward Swing Arm s 1 4 I.D. for Straight Tubes, Bent Tubes and Drill Pipe Forward swing arm heads, components and (ordering numbers) Recommended spare parts: cone cutters and cutter pins, cutter arms and arm pins. Figure 1 Shown with head coupling for straight tubes. Figure 2 Shown with universal coupling for bent tubes. Tube I.D. Closed Epands To Spider Figure Long Arm Short Arm Cpl. Cpl. Tap Long Cutter Pin Short Cutter Pin Arm Pin Pin Lock Cone Cutter Star Cutter No. of Arms 1840 ( ) 1840 B ( ) 2340 ( ) 4440 ( ) 4470 ( ) 4470 A ( ) 3370 ( ) 3370 A ( ) 3270 ( ) 3270 A 7/8 ( ) 970 ( ) 970 B ( ) 770 ( ) 770 B ( ) 1 11/2" 21/8" 2 11/2" 21/8" 2" 1 3" 2" 1 3" 2 2" 3 2 2" " 21/2" 4" 3" 21/2" 4" /2" 3" 4 31/2" 3" ( ) 31/4 4" 3 51/8" 870 B ( ) 31/4 4" 3 51/8" 770 S A ( ) 770 S /2" /2" 1841 ( ) 1841 ( ) 2341 ( ) 2341 ( ) 4471 ( ) 4471 ( ) 3371 ( ) 3371 ( ) 3271 ( ) 3271 ( ) 971 ( ) 971 ( ) 771 ( ) 771 ( ) S ( ) 771 S ( ) (1) ( ) 1842 (1) ( ) 1842 A (1) ( ) 1842 A (1) ( ) 1832 (1) 1832 A (1) ( PT)( PT) MM 66 ( ) 1832 (1) 1832 A (1) MM 66 ( PT)( PT) ( ) 4472 (3) ( ) 4472 (3) ( ) 3372 (3) ( ) 3372 (3) ( ) 3472 (2) ( ) 3472 (2) ( ) 972 (2) ( ) 972 (2) ( ) 772 (2) ( ) 772 (2) ( ) 772 (2) ( ) 772 (2) ( ) 772 S (4) ( ) 772 S (4) ( ) 3272 (2) ( ) 3272 (2) ( ) 972 A (2) ( ) 972 A (2) ( ) 772 A (2) ( ) 772 A (2) ( ) 772 A (2) ( ) 772 A (2) ( ) MM 66 ( ) 2383 B ( ) 3551 ( ) /8 ( ) 3551 ( ) /8 ( ) 543 7/8 ( ) 551 ( ) 873 A ( ) 1151 ( ) 873 A 1151 ( ) 543 7/8 ( ) 551 ( ) 1834 (1) ( ) 1834 (1) ( ) 1834 (1) ( ) 1834 (1) ( ) 4474 (3) ( ) 4474 (3) ( ) 3374 (3) ( ) 3374 (3) ( ) 3474 (2) ( ) 3474 (2) ( ) 974 (2) ( ) 974 (2) ( ) 774 (2) ( PT) 774 (2) ( PT) 774 (2) ( PT) 774 (2) ( PT) 774 S (4) ( ) 774 S (4) ( ) 1834 A (1) ( ) 1834 A (1) ( ) 1834 A (1) ( ) 1834 A (1) ( ) 3274 (2) ( ) 3274 (2) ( ) 974 A (2) ( ) 974 A (2) ( ) 774 A (2) ( ) 774 A (2) ( ) 774 A (2) ( ) 774 A (2) ( ) 1845 (2) ( PT) 1845 (2) ( PT) 2345 (2) ( ) 2345 (2) ( ) 4475 (3) ( ) 4475 (3) ( ) 3375 (3) ( ) 3375 (3) ( ) 3275 (2) ( ) 3275 (2) ( ) 975 (4) ( ) 975 (4) ( ) 775 (4) ( ) 775 (4) ( ) 1846 ( ) 1846 ( ) 2346 ( ) 2346 ( ) 4476 ( ) 4476 ( ) 3376 ( ) 3376 ( ) 3276 ( ) 3276 ( ) 976 (4) ( ) 976 (4) ( ) 776 ( ) 776 ( ) 337 (2) ( ) 337 (2) ( ) 337 (2) ( ) 337 (2) ( ) C 19 (3) ( ) C 19 (3) ( ) 637 (3) ( ) 637 (3) ( ) 1047 (2) ( ) 1047 (2) ( ) 637 (4) ( ) 637 (4) ( ) 747 (4) ( ) 747 (4) ( ) 875 (4) (4) ( ) 875 (4) (4) ( ) 775 (4) ( ) 775 (4) ( ) 776 S (4) ( ) 776 S (4) ( ) 747 (4) ( ) 747 (4) ( ) 338 (3) ( ) 338 (3) ( ) 338 (3) ( ) 338 (3) ( ) (2) ( ) 2837 (2) ( ) mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
23 Type 4 SRA Spring Retracting Arm s 11/2" 4 I.D. for Straight Tubes, Bent Tubes, and Drill Pipe Forward swing arm heads, components and (ordering numbers) Recommended spare parts: cone cutters and cutter pins, cutter arms and arm pins. Developed specifically for Drill Pipe applications to protect bo end threads The SRA arms are held closed until air is applied which allows for easy insertion into the bo end of drill pipe, especially when used with automated cleaning equipment SRA /16 ( PT) SRA /8 ( PT) SRA /4 ( ) SRA /8 ( ) SRA /8 ( ) SRA 3270 UJK ( PT) SRA 970 7/8 ( ) SRA 770 7/8 ( PT) SRA /8 ( PT) Tube I.D. Closed Epands To 11/2" 1 2 2" " 31/2" " 21/2" 4" 3" 21/2" 4" /2" 3" 4 43/4' 2 51/2" Spider 1471 ( PT) 1871 ( PT) 4471 ( ) 3371 ( ) 3271 ( ) 3271 ( ) 971 ( ) 771 ( ) 771 ( ) Fig Long Arm 1472 (3) ( PT) 4472 (3) ( ) 4472 (3) ( ) 3372 (3) ( ) 3472 (2) ( ) 3472 (2) ( ) 972 (2) ( ) 772 (2) ( ) 772 S (4) ( ) Short Arm SRA /16 ( PT) SRA 1873 ( PT) SRA /4 ( ) SRA /8 ( ) 3272 (2) SRA /8 ( ) ( ) 3272 (2) ( ) 972 A (2) ( ) 772 A (2) ( ) SRA 3273U ( PT) SRA 973 7/8 ( ) SRA 773 7/8 ( ) SRA 773 7/8 ( ) Tap 9/16" Long Cutter Pin 1474 (3) ( PT) 4474 (3) ( ) 4474 (3) ( ) 3374 (3) ( ) 3474 (2) ( ) 3474 (2) ( ) 974 (2) ( ) 774 (2) ( ) 774 S (4) ( ) Short Cutter Pin 3274 (2) ( ) 3274 (2) ( ) 974 A (2) ( ) 774 A (2) ( ) Arm Pin Pin Lock Cone Cutter 1475 (3) SRA (3) ( PT) ( PT) ( ) 4475 (3) ( ) 4475 (3) ( ) 3375 (3) ( ) 3275 (4) ( ) 3275 (4) ( ) 975 (4) ( ) 775 (4) ( ) 775 (4) ( ) SRA 1876 C 19 (3) ( PT) ( ) SRA 4476 ( ) SRA 3376 ( ) SRA 3276 ( ) SRA 3276 ( ) SRA 976 ( ) SRA 776 ( ) SRA 776 ( ) C 19 (3) ( ) 637 (3) ( ) 1047 (2) ( ) 1047 (2) ( ) 637 (4) ( ) 747 (4) ( ) 747 (4) ( ) Star Cutter 2837 (2) ( ) 2837 (2) ( ) Spring SRA 1479 ( PT) SRA 1879 ( PT) SRA 4479 ( ) SRA 3379 (171433) SRA 3379 (171433) SRA 3379 (171433) SRA 3379 ( ) SRA 779 ( ) SRA 779 ( ) Universal Joint 651 KNF ( PT) No. of Arms mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
24 Type 5 Self Feed Clip Type Wing Arm s 1 8 I.D. for Straight Tubes and Pipe Wing arm heads, components and (ordering numbers) Tube I.D. Closed Epands To Spider Arm (Qty.) Plate Tap Cutter Pin Arm Pin Clip Cone Cutter Cylinder Cutter Washer ( ) 1 11/2" 21/8" ( ) (2) ( ) B ( ) (2) ( ) (2) ( ) (2) ( ) (8) ( ) /8 ( ) ( ) 3062 S (3) ( ) 3043 ( ) 3364 (3) ( ) 3365 (3) ( ) 3068 (3) ( ) 3047 (3) ( ) 3048 (3) ( ) /4 ( ) ( ) 3062 S (3) ( ) /4 ( ) 3364 (3) ( ) 3365 (3) ( ) 3068 (3) ( ) 3047 (3) ( ) 3048 (3) ( ) /4 ( ) 21/2" 2 3" 3361 ( ) 3362 S (3) ( ) /4 ( ) 3364 (3) ( ) 3365 (3) ( ) 3368 (3) ( ) 337 (3) ( ) 338 (15) ( ) 339 (3) ( ) /8 ( ) 21/2" 2 3" 3361 ( ) 3362 S (3) ( ) /8 ( ) 3364 (3) ( ) 3365 (3) ( ) 3368 (3) ( ) 337 (3) ( ) 338 (15) ( ) 339 (3) ( ) /4NC ( ) 3" ( ) 1062 S (3) ( ) /4 ( ) 1064 (3) ( ) 1065 (3) ( ) 1068 (3) ( ) 1047 (3) ( ) 1048 (15) ( ) /8THD ( ) 3" ( ) 1062 S (3) ( ) /8 ( ) 1064 (3) ( ) 1065 (3) ( ) 1068 (3) ( ) 1047 (3) ( ) 1048 (15) ( ) NF ( ) 3" ( ) 1062 S (3) ( ) ( PT) 1064 (3) ( ) 1065 (3) ( ) 1068 (3) ( ) 1047 (3) ( ) 1048 (15) ( ) 960 ( ) 3 31/8" 41/8" 961 ( ) 762 S (3) ( ) 543 7/8 ( ) (3) ( ) 765 (3) ( ) (3) ( ) 947 (3) ( ) 948 (27) ( ) 749 (3) ( PT) ( ) 31/2" 3 41/2" 761 ( ) 762 S (3) ( ) ( ) (3) ( ) 765 (3) ( ) (3) ( ) 747 (3) ( ) 748 (24) ( ) 749 (3) ( PT) /8 ( ) 31/2" 3 41/2" 761 ( ) 762 S (3) ( ) /8 ( ) 11/8" (3) ( ) 765 (3) ( ) (3) ( ) 747 (3) ( ) 748 (24) ( ) 749 (3) ( PT) 5060 AS ( ) 41/2" A ( ) 562 S (3) ( ) 843 ( ) 5043 A 11/8" 564 (3) ( ) 565 (3) ( ) 568 (3) ( ) 747 (3) ( ) 748 (24) ( ) 749 (3) ( PT) /2" 6" S (4) ( ) A (4) ( ) (4) ( ) (4) ( ) 271 (4) ( ) C 79 (12) ( ) 749 (4) ( PT) /8 6" 5 71/8" ( ) S (4) ( ) /8" N.F (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) /8 6" 5 71/8" ( ) S (4) ( ) (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) /8 ( ) 61/2" C ( ) S (4) ( ) B ( ) AC ( ) 11/8" (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) " S (4) ( ) 8293 ( ) A (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) /2" 81/2" S (4) ( ) 8293 ( ) A (5) ( ) (5) ( ) (5) ( ) (5) ( ) (15) ( ) (5) ( ) ( ) 8 71/2" 91/2" ( ) S (4) ( ) 8293 ( ) A ( ) (5) ( ) (5) ( ) (5) ( ) (5) ( ) (15) ( ) (5) ( ) mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
25 Type 5 Self Feed Clip Type Wing Arm s 13/4 " 9" I.D. for Curved Tubes and Pipe Wing arm heads, components and (ordering numbers) Tube I.D. Closed Epand To Spider Arm Universal Plate Tap Cutter Pin Arm Pin Clip Cone Cutter Cylinder Cutter Washer C ( ) 2" 11/2" 21/8" ( ) (2) ( ) 4151 W ( ) (2) ( ) (2) ( ) (2) ( ) (8) ( ) 3060 C S (3) 4151 ( ) 3364 (3) ( ) 3365 (3) ( ) 3068 (3) 3047 (3) 3048 (3) 3360 ( ) 2 2 3" 3361 ( ) 3362 S (3) ( ) 3333 ( PT) 3364 (3) ( ) 3365 (3) ( ) 3368 (3) ( ) 337 (3) ( ) 338 (15) ( ) 339 (3) ( ) /4 ( ) ( ) 1062 S (3) ( ) /4 ( ) 1064 (3) ( ) 1065 (3) ( ) 1068 (3) ( ) 1047 (3) ( ) 1048 (15) ( ) /8 ( ) ( ) 1062 S (3) ( ) /8 ( ) 1064 (3) ( ) 1065 (3) ( ) 1068 (3) ( ) 1047 (3) ( ) 1048 (15) ( ) 960 C ( ) 31/2" 31/8" ( ) 762 S (3) ( PT) 551 ( ) (3) ( ) 765 (3) ( ) (3) ( ) 947 (3) ( ) 948 (27) ( ) 749 (3) ( PT) 760 C ( ) /2" 761 ( ) 762 S (3) ( PT) 1151 ( ) (3) ( ) 765 (3) ( ) (3) ( ) 747 (3) ( ) 748 (24) ( ) 749 (3) ( PT) 760 C 11/8 ( PT) /2" 761 ( ) 762 S (3) ( PT) 5051 E ( ) 11/8" (3) ( ) 765 (3) ( ) (3) ( ) 747 (3) ( ) 748 (24) ( ) 749 (3) ( PT) 5060 A ( ) 413/16" A ( ) 562 S (3) ( ) 5051 E ( ) 5043 A ( ) 11/8" 564 (3) ( ) 565 (3) ( ) 568 (3) ( ) 747 (3) ( ) 748 (24) ( ) 749 (3) ( PT) C 5 41/2" 6" S (4) ( ) 5051 H ( ) A 11/8" (4) ( ) (4) ( ) (4) ( ) 271 (4) ( ) C 79 (12) ( ) 749 (4) ( PT) C ( ) 6" 5 71/8" ( ) S (4) ( ) 5051 H ( ) A ( ) 11/8" (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) C ( ) 61/2" C ( ) S (4) ( ) 5051 H ( ) AC ( ) 11/8" (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) C 7 6 8" S (4) ( ) A ( ) A (4) ( ) (4) ( ) (4) ( ) (4) ( ) (12) ( ) (4) ( ) C 7 61/2" 81/2" S (5) ( ) A ( ) A (5) ( ) (5) ( ) (5) ( ) (5) ( ) (15) ( ) (5) ( ) C 8 71/2" 91/2" S (5) ( ) A ( ) A (5) ( ) (5) ( ) (5) ( ) (5) ( ) (15) ( ) (5) ( ) 108 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
26 Drill s Drill s Tube I.D. range 1/2" thru 3 Airetool drill heads are made from alloy steel For strength and durability Drills can be used with etensions (below) for larger tube I.D. s as required Universal coupling ordered separately Tube I.D. Drill Order Hard Surfaced Hard Surfaced Order Drill O.D. Stud Thread Size of Flutes Weight (Lbs.) 1/2" MD NA 7/16" MD NA 1/2" /16" 13/16" MD NA /8" MD NA /8" 1 MD NA 13/16" 7/16" S 1 1/16" 7/16" /2" S 1 1/2" S S S /16" S " 63/ /4S " S " 4 1/2" S /2" 9" S *9" S /8" " S /8" Drill Etensions Male to Female Thread Description Male Female Male Female 11/8" Male 11/8" Female Length (in.) Model No. Order No. Model No. Order No. Model No. Order No A PT B PT C PT 5056 A A D PT 5056 B B C C D D E E H PT 5056 F F mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
27 Epanding Blade Type Epanding Blade Type Tube I.D. range 1/2" thru 41/2" When ordering specify the motor number and the motors shaft thread size ( ) 2780 ( ) 6480 ( ) 2980 ( ) 6180 ( ) 2680 ( ) /16 NF ( PT) /8 ( ) /8 NF ( PT) /16 NF ( PT) 1780 ( PT) 1880 ( PT) 1980 ( PT) 2380 C ( PT) 2380 ( PT) S ( PT) ( ) ( PT) H Tube I.D. Minimum Diameter Maimum Diameter Stud Size 1/2" 29/64" 37/64" /16" 11/16" 11/16" 13/16" 13/16" 25/32" 29/32" 13/32" 1 15/32" 11/8" 11/32" /32" /32" 11/2" 1 19/32" 11/2" 11/2" 1 111/16" 1 11/2" 113/16" /16" 2" 1 23/16" 21/8" /2" 21/8" " /2" 31/8" 3 4" 3 41/8" 41/2" 41/8" 4 9/16" Blade Body 2481 ( ) 3081 ( ) 2781 ( ) 2981 ( ) 2981 ( ) 6181 ( ) 6181 ( ) 3181 ( ) 3181 ( ) 3181 ( ) 3181 ( ) 1781 ( PT) 1881 ( PT) 1881 ( PT) 1881 ( PT) 2381 ( PT) S ( PT) Rear Retainer 2483 ( ) 3083 ( ) 2783 ( ) 2983 ( ) 2983 ( ) 6183 ( ) 6183 ( ) 3183 ( ) 3183 ( ) 3183 ( ) 3183 ( ) 1783 ( PT) 1883 ( PT) 1883 ( PT) 1883 ( PT) 2383 ( PT) S ( PT) Blade Set 2487 ( ) 3087 ( PT) 2787 ( ) 6487 ( ) 2987 ( ) 6187 ( PT) 2687 ( PT) 3187 ( ) 6387 ( PT) 6587 ( ) 6587 ( ) 1787 ( ) 1887 ( PT) 1987 ( PT) 2387 C ( PT) 2387 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( PT) ( ) ( ) ( ) ( ) ( PT) ( ) ( ) ( ) ( ) ( ) Blade 2487 (4) ( ) 3087 (3) ( ) (3) ( ) 6487 (3) ( ) 2987 (3) ( ) 6187 (4) ( ) 2687 (4) ( ) 3187 (4) ( ) 6387 (4) ( ) 6587 (4) ( PT) 6587 (4) ( PT) 1787 (4) ( ) 1887 (4) ( PT) 1987 (4) ( PT) 2387 C (4) ( PT) 2387 (4) ( PT) (4) ( PT) (4) ( PT) (4) ( PT) (6) ( PT) (6) ( PT) FF 1010 ( ) FF 22 ( ) FF 22 ( ) FF 312 ( ) FF 3137 ( ) FF3137 ( ) FF3137 ( ) FF 314 ( PT) FF3137 ( ) FF3137 ( ) FF314 ( ) FF 5656 ( PT) FF 66 ( ) FF 66 ( ) FF 66 ( ) FF 66 ( ) FF 66 ( ) FF 77 ( ) FF 78 ( ) Tap /16" 7/16" 9/16" FF 88 FF 11 ( PT) (6) FF 11 ( PT) ( ) ( ) (6) ( ) (6) ( ) FF 111 ( ) FF 111 ( ) H H (6) FF 111 ( ) 11/8" 11/8" 11/8" 110 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
28 UJoints 1032 thru thread combinations For adapting cleaning heads to cleaning motors Ujoints, components and ordering numbers Universal Jont No. Shaft Jaw Jaw Link Pin (2 req.) UJoint O.D. (in.) Overall Length (in.) Thread Size Cleaner Kits Used On 2451 ( ) 2452 ( ) 2452 ( ) 2454 ( ) 2455 ( ) PA 3051 ( ) PA 3052 ( ) PA 3052 ( ) PA 3054 ( ) PA 3055 ( ).437 (.375 He) , 27 A, 30, 30 A 6451 ( ) 6453 V ( ) 6453 V ( ) 6454 V ( ) 6455 V ( ) X B 6453 V ( ) 6457 V ( ) 6454 V ( ) 6455 V ( ) N.F X C ( ) 6452 V ( ) 6453 V ( ) 6454 V ( ) 6455 V ( ) X 60, X ( PT) 6452 V ( ) 6452 V ( ) 6454 V ( ) 6455 V ( ) X B ( ) 6452 V ( ) 6457 V ( ) 6454 V ( ) 6455 V ( ) X ( ) 2652 ( PT) 2652 ( PT) 2654 ( ) 2655 ( ) , B ( ) 6652 ( ) ( ) 6655 ( ) X B ( ) 6651 ( ) 6652 ( ) 6652 ( ) 6658 ( ) 6653 ( ) 6654 ( ) 6654 ( ) 6655 ( ) 6655 ( ) /16" 7/16" X 65, X 66 31, X 63, X 65, X ( ) 6653 ( ) 6653 ( ) 6654 ( ) 6655 ( ) 7/16" 7/16" ( ) 4153 ( ) 4157 ( ) 4154 ( ) 4155 ( ) 9/16" 1/2" W ( ) 4152 ( ) 4153 ( ) 4154 ( ) 4155 ( ) /2" C 4151 ( ) 4152 ( ) 4152 ( ) 4154 ( ) 4155 ( ) 3162, 3175, 3187, 3200, , 4225, 4237, 4250, ( PT) 3552 ( ) 3332 ( ) 3554 ( ) 3555 ( ) ( ) 3531 ( ) 3552 ( ) 3557 ( ) 3533 ( ) 3533 ( ) 3554 ( ) 3554 ( ) 3555 ( ) 3555 ( ) , /4 Rotor Thread 3540, /8 Rotor Thread mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
29 UJoints thru 138" thread combinations For adapting cleaning heads to cleaning motors Ujoints, components and ordering numbers Universal Jont No. Shaft Jaw Jaw Link Pin (2 req.) UJoint O.D. (in.) Overall Length (in.) Thread Size Cleaner Kits Used On 2251 ( ) 3553 ( ) 3553 ( ) 3554 ( ) 3555 ( ) 2151 ( ) 3551 ( ) 3552 ( ) 3552 ( ) 3553 ( ) 3552 ( ) 3554 ( ) 3554 ( ) 3555 ( ) 3555 ( ) , , 4300 A, A 3552 ( ) 3552 ( ) 3554 A 3555 ( ) Deg. Restricterd ( ) 654 ( ) 255 ( PT) 3/ ( ) 255 ( PT) ( ) ( ) 1553 ( ) 654 ( ) 255 ( PT) , H ( ) 653 ( PT) 653 ( PT) 654 ( ) 655 ( ) 651 ( ) 652 ( ) 651 A 652 ( ) 653 ( PT) 653 ( PT) 654 ( ) 655 ( ) 654 A 655 ( ) , 3287, Deg. Restricterd 551 ( ) 652 ( ) 652 ( ) 654 ( ) 655 ( ) , 4425, 4450, 4450 A ( ) 1151 ( ) 1152 ( ) 1152 ( ) ( ) 1153 ( ) 1154 ( ) 1154 ( ) 1155 ( ) 1155 ( ) , , 3318, 3325, ( ) 5052 ( PT) 1153 ( ) 1154 ( ) 5055 ( ) 1155 ( ) 11/8" 3350 through ( ) 5052 ( PT) 5051 E 5052 ( PT) 5057 ( ) 1154 ( ) ( ) 5055 ( ) 5055 ( ) /8" 11/8" 4481, 4500, , 4600, 4650, 4712, H ( ) 5052 ( PT) 5052 ( PT) 1154 ( ) 5055 ( ) 11/8" 11/8" H ( ) ( ) ( ) ( ) ( ) through ( ) ( ) ( ) ( ) ( ) /8" N.F N.F 3975 through A ( ) ( ) ( ) ( ) ( ) 1 1 N.F 112 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
30 Adapters These adapters are used to configure motors and heads in special applications where the standard Airetool offering does not match up on thread sizes. Female X Female Male X Male Male X Female Part Female X Female Part Male X Male Part Male X Female FF X X 1032 MF 22 1/4 X 1/4 FF X 5/16 MM X 5/16 MF 231 1/4 X 5/16 FF 22 1/4 X 1/4 MM 250 1/4 X 1/4 MF 231 F 1/4 X 5/16 FF 231 1/4 X 5/ /4 X 5/16 MF 312 5/16 X 1/4 FF 237 1/4 X 3/8 MM 24 1/4 X 7/16 MF 312 F 5/16 X 1/4 FF 312 5/16 X 1/4 MM /16 X 1/4 MF /16 X 5/16 FF /16 X 5/16 MM /16 X 5/16 MF 3131 F 5/16 X 5/16 FF3137 5/16 X 3/8 MM 3131 F 5/16 X 5/16 MF 314 5/16 X 7/16 FF314 5/16 X 7/16 MM /16 X 3/8 MF 314 F 5/16 X 7/16 FF 374 3/8 X 7/16 MM /8 X 3/ /8 X 1/4 FF 374 F 3/8 X 7/16 MM 3737 F 3/8 X 3/8 MF /8 X 5/16 FF 376 3/8 X 5/8 MM 374 3/8 X 7/16 MF 3731 F 3/8 X 5/16 FF 437 7/16 X 3/8 MM 374 F 3/8 X 7/ /8 X 5/16 FF 45 7/16 X 1/2 MM 437 7/16 X 3/8 MF /8 X 3/8 FF 456 7/16 X 9/16 MM 44 7/16 X 7/16 MF 374 3/8 X 7/16 FF 46 7/16 X 5/8 MM 456 7/16 X 9/16 MF 374 F 3/8 X 7/16 FF 47 7/16 X 3/4 MM 46 7/16 X 5/8 MF 431 7/16 X 5/16 FF 54 1/2 X 7/16 MM /2 X 9/16 MF 431 F 7/16 X 5/16 FF 56 1/2 X 5/8 MM 56 1/2 X 5/8 MF 433 7/16 X 3/8 FF 56 F 1/2 X 5/8 MM 564 9/16 X 7/16 MF /16 X 7/16 FF 564 9/16 X 7/16 MM /16 X 1/2 MF 435 7/16 X 1/2 FF /16 X 9/16 MM /16 X 9/16 MF 435 F 7/16 X 1/2 FF 566 9/16 X 5/8 MM 566 9/16 X 5/8 MF 436 7/16 X 5/8 FF 567 9/16 X 3/4 MM 567 9/16 X 3/4 MF 436 F 7/16 X 5/8 FF 637 5/8 X 3/8 MM 568 9/16 X 7/8 MF 531 1/2 X 5/16 FF 64 5/8 X 7/16 MM 561 9/16 X /2 X 3/8 FF 65 5/8 X 1/2 MM 66 5/8 X 5/8 MF 543 1/2 X 7/16 FF 66 5/8 X 5/8 MM 67 5/8 X 3/4 MF 543 F 1/2 X 7/16 FF 66 F 5/8 X 5/8 MM 68 5/8 X 7/8 MF 56 1/2 X 5/8 FF 67 5/8 X 3/4 MM 77 3/4 X 3/4 MF 56 F 1/2 X 5/8 FF 68 5/8 X 7/8 MM 78 3/4 X 7/8 MF 57 1/2 X 3/4 FF 77 3/4 X 3/4 MM 88 7/8 X 7/8 MF 563 9/16 X 3/8 FF 78 3/4 X 7/84 MM 81 7/8 X 1 MF 565 9/16 X 1/2 FF 856 7/8 X 9/16 MM 11 1 X 1 MF 566 9/16 X 5/8 FF 86 7/8 X 5/8 MM X 11/8 MF 567 9/16 X 3/4 FF 88 7/8 X 7/8 MM /8 X 11/8 MF 568 9/16 X 7/8 FF 81 7/8 X 1 MM /8 X 13/8 MF 561 9/16 X 1 FF 16 1 X 5/8 MF 631 5/8 X 5/16 FF 17 1 X 3/4 MF 637 5/8 X 3/8 FF 11 1 X /8 X 7/16 FF X 11/8 MF 65 5/8 X 1/2 FF /8 X 7/8 MF 656 5/8 X 9/16 FF /8 X 11/8 MF 68 5/8 X 7/8 MF 743 3/4 X 7/16 MF 743 F 3/4 X 7/16 MF 76 3/4 X 5/8 MF 71 3/4 X 1 MF 711 3/4 X 11/8 MF 86 7/8 X 5/8 MF 86 F 7/8 X 5/8 MF 87 7/8 X 3/4 MF 81 7/8 X 1 MF 811 7/8 X 11/8 MF 813 7/8 X 13/8 MF 16 1 X 5/8 MF 18 1 X 7/8 MF X 11/8 MF /8 X 13/8 MF /8 X 7/8 MF /8 X 13/8 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
31 Fleible Connections Fleible Connections Use for connecting cleaning head to motor when cleaning tubes with short radius bends. Fleible connectors come complete with female/female couplings in lengths from 4 14 inches ( mm) A length C length Part Order Thread Size 2461 A X 1032 Core Diameter Cleaner Motor Options 2461 C X X 6461 C /4 X 1/4 30,27, X64 3/16" X /4 X 5/16 27, X64 X 6161 A /16 X 5/16 X61 X 6161 C /16 X 5/16 X A /8 X 5/ A /8 X 3/8 29 X 6361 A /8 X 7/16 X63, C /16 X 5/16 31 X 6661 A /8 X 7/16 X 6662 A /8 X 7/16 X65, X A /16 X 7/ A /8 X 5/ X65, X , A /8 X 9/16 Male 4200, 4225, /2" 4163 C /8 X 7/ /16 X 1/ C /4 X 3/4 4300, C /4 X 9/16 Male 3225, 4300, C /4 X 5/ /8 X 9/16 Male 3200, C /8 X 3/4 4350, /8 X 7/8 4350, C /8 X 7/8 Male /8 X 9/16 Male 3250, C X 7/ C /8 X 11/8 3350, 3400, C /8 X 7/8 3350, 3400, /8 X 7/8 Male 3350, 3400, /8 X , 3400, /8 X and up /8 X 1 1/ and up /8 X 13/8 Male 3500 and up Type A Type C Appro. Length (in.) Wt. Appro. Length (in.) Wt..06# #.08# #.40#.25#.45# # 1.0# 1.5# # Not Available 3.1# 114 mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
32 Overhead Catalyst Cleaners Overhead Catalyst Cleaners Overhead catalyst cleaner systems are specifically designed for the safe removal of spent catalyst from the top of the reactor tower. The system collects the catalyst carried by the ehaust air and discharges the spent catalyst into any suitable container. Helps eliminate the danger of catalyst contacting the operator Uses highpowered, highperformance air motor to remove catalyst quickly and efficiently Cleaner systems are available for tubes from 13/16" up to 5" diameter (I.D.) Specify tube size and gauge when ordering FC Shown below (1 5/82) dust seal dust seal gasket female coupling clamp disposal tube male coupling 3 pipe thread Cleaner Complete eample (See picture at right) Model Ordering Description Quantity OHC Cleaner Complete* (~85 lbs.) SPARE MOTOR BLADES 4 OHC MAIN CLEANER BODY 1 FC / FC TYPE DRILL BIT 1 DIA. 1 OHC DUST SEAL ASSEMBLY 1 OHC / OHC TYPE DRILL BIT 1 DIA. 2 OHC DUST SEAL GASKET 3 OHC RENEWABLE PILOT 1 WRENCH 5/ SHAFT WRENCH AIR MOTOR 1 OHC / OPERATING HOSE & COUPLINGS 50FT 1 OHC DISPOSAL TUBE ASSEMBLY 1 * Cleaner Complete includes three drill bits, three etra dust seal gaskets, a spare set of motor blades, and motor shaft wrench(s) 3/4 operating hose renewable tapered pilot 3/4 pipe thread 3162 motor 5/8 11 shaft thread OHC2509 type drill bit fc200 type drill bit Catalyst Cleaner Bits Model Order Description FC2001 1/4 5/8NC PT Drill Bit 1 Diameter FC2001 3/ Drill Bit 1 Diameter FC2001 1/2 9/16NC Drill Bit 11/2" Diameter FC2001 5/8 9/16NC Drill Bit 1 Diameter FC2001 5/8 5/8NC Drill Bit 1 Diameter FC2001 3/4 5/8NC Drill Bit 1 Diameter FC2001 7/8 5/8NC Drill Bit 1 Diameter FC /16 5/8NC Drill Bit 11 Diameter FC /32 5/8NC Drill Bit 123/32" Diameter FC /2 7/8NC Drill Bit 21/2" Diameter OHC / Drill Bit 1 Diameter OHC / Drill Bit 1 Diameter OHC / Drill Bit 1 Diameter mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
33 Accessories Model FV100 Foot Valve For quick control of air when cleaning tubes. Has LOCK ONEASY OFF feature. Easily secured to working platform or most convenient location. Model Order Length Width Height NPT Weight in. mm in. mm in. mm in. Lbs. kg FV InLine Lubricator Lubricator stays connected to the tool. Internal adjustment of lubrication rate. Ordering Hose Size Lubricator Bowl Capacity /2 NPT #0 1/6 pt (7 cl) /4 NPT #1 1/3 pt (15 cl) /4 NPT #2 1/2 pt (23 cl) NPT #3 1 pt (47 cl) Air Hose Selection Guide Note: Standard WBLHWW braid hose has one layer wire braid and a left hand wire wound outside hose protector. Hose Size (in.) Working Pressure PSI Length ft. Model Order Air Pipe Wire Wound (W/W) Hose OD (over wire) ft. M Tap Size (in.) Not Wire Wound (N/WW) in. mm Air Motor 25 3/ /16" 25 ft N/WW / /16" 50 ft N/WW Air Motors 27, 27A, 30, 30A 1/ ft /8 N/WW / ft /8 N/WW Air Motors X64, X61 1/ ft /4 N/WW / ft /4 N/WW Air Motor 29 3/ ft /4 N/WW / ft /4 N/WW Air Motors 26, 31 3/ ft /8 N/WW / ft /8 N/WW Air Motors X63, X63A, X65, X65A, X66 3/ ft.wblhww /8 Left hand W/W / ft.wblhww /8 Left hand W/W Air Motors 3150, 3175, 4200, 4225, / /2" 25 ft.wblhww /2 Left hand W/W / /2" 50 ft.wblhww /2 Left hand W/W Air Motors 3162, 3187, 3200, 3225, 3212, 4300, / ft.wblhww /4 Left hand W/W / ft.wblhww /4 Left hand W/W All other air motors ft.wblhww Left hand W/W ft.wblhww Left hand W/W mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
34 Accessories Ergonomic Tool Balancers Capacity 1 45 lbs kg Eternal tension adjustment 360 Swivel Retracting inline cable BL6A BM13A Model Lock Feature Capacity A B C Weight lbs. kg in. mm in. mm in. mm lbs. kg Light Duty 5.2 ft. (1.6m) Cable Travel BL2A BL4A Light Duty 6.7 ft. (2.0m) Cable Travel BL6A BLL6A Ratchet BL8A BLL8A Ratchet Medium Duty 6.6ft. (2.0m) Cable Travel BM13A NonLocking BM13A Lock/Release BM18A NonLocking Medium Duty 6.0ft. (1.8m) Cable Travel BM25A Automatic BM35A Automatic BM45A Automatic mdi Manufacturers Distributor, Inc Phone: (813) Fa: (813)
Tube Cleaners Introduction
Tube Cleaners Introduction Clean tubes mean lower fuel costs. All piping, heat echangers, condensers, chillers, and boiler tubes accumulate scale over various periods of use. This scale decreases flow
More informationTube Cleaners Heat Exchanger & Condenser Cleaning Systems
System Components Motors CC475 & CC475PS I CC375 CC325 CC325HP s DRIVE COUPLING DRIVE SHAFT SHAFT COUPLING Drills and Brushes DRIVEN SHAFT CT DRILL TW DRILL AT DRILL CB DRILL SPIRAL BRUSH Complete Cleaning
More informationBoiler Tube Cleaners Tube Cleaners for Straight Tubes
Tube Cleaners for Straight Tubes 1/2" to 1-3/8" (12.7 to 34.9 mm) I.D. Range: 1/2 in. (12.7 mm) - 1-3/8 in. (34.9 mm) Deposit: heavy-medium to soft Midget Motor with optional heads shaft wrench; metal
More informationTube Cleaners.
Tube Cleaners www.elliott-tool.com Tube Cleaners Table of Contents Pg. Tube Cleaners 2 5370 Jiffy Gun 3 537100C Jumbo Jiffy Gun 4 Jiffy Gun & Jumbo Jiffy Gun Spares & Accessories 5 Soot Buster 5 Soot Buster
More informationTube Installation.
Tube Installation www.elliott-tool.com Tube Installation Table of Contents Page Tube Installation 2 Tube Hole Gauges 4 Tube Sheet Hole Brushes 5 Grooving (Serrating) Tools 6 Tube Auger / End Prep 7 Hand
More informationELECTRIC TUBE CLEANERS
ELECTRIC TUBE CLEANERS 1 4 &UP FLEXIBLE SHAFT CAN BE STORED ON HANDLE ELECTRIC TUBE CLEANERS QUICK CONNECT OF SHAFT TO CLEANER POWER INDICATOR LIGHT WATER IN-FLOW THROUGH STANDARD HOSE CONNECTOR LARGE
More informationHOSES & LANCES. Hoses & Lances 15,000 PSI (1,034 BAR)
HOSES & LANCES Jetstream provides a full arrangement of hoses and flex lances for high pressure waterblasting. The hoses and lances are designed to be durable and reliable for any 15,000 psi application.
More informationThomas C. Wilson, Inc. Tube Cleaning Equipment, Accessories and Supplies
Tube Cleaning Equipment, Accessories and Supplies WET AND DRY TUBE CLEANING SYSTEMS ELECTRIC, PNEUMATIC, AND AIR MOTORS SHAFTS AND CASINGS, BRUSHES, SCRAPERS, ACCESSORIES AND SUPPLIES Thomas C. Wilson,
More informationTube Plugs.
Tube Plugs www.elliott-tool.com Tube Plugs Table of Contents Page Tube Plugs Aluminum Siphons Boilers-Firetube Boilers-Watertube Sugar Mill Vacuum Pans Surface Condensers Chillers & Heat Exchangers Feedwater
More informationThomas C. Wilson, Inc. Tube Cleaning Equipment, Accessories, and Supplies
Tube Cleaning Equipment, Accessories, and Supplies Tools for cleaning tubes in... heat exchangers Fire tube and water tube boilers Condensers, chillers, and absorbers and other tubular structures and pressure
More informationTubing Cutter for 1/16" Stainless Steel Tubing
Delivery Tubing and ccessories 311 P000257 Tubing Cutter for 1/16" Stainless Steel Tubing 58692-U Low-cost tool cuts 1/16" stainless steel tubing without obstructing the bore. Easily cut 1/16" OD stainless
More informationHelaGuard. Non-Metallic Conduit & Fittings
HelaGuard Non-Metallic Conduit & Fittings HelaGuard Non-Metallic Conduit Systems Page HelaGuard Overview 3 Conduit Application Overview 4 Mounting & Removing HelaGuard Non-Metallic Fittings 5 HelaGuard
More informationCable Management Solutions. HelaGuard. Non-Metallic Conduits and Fittings
Cable Management Solutions HelaGuard Non-Metallic Conduits and Fittings Table of Contents Page HelaGuard Overview 4 Conduit Application Overview 6 Mounting & Removing HelaGuard Non-Metallic Fittings 7
More informationTools. Acid Brush. Utility Brush. Brushes For Cleaning Copper Fittings G113 01/06/18
Acid Brush G113 Manufactured with electrolyte tin plate and filled with 100% pure stiff black horse hair which is firmly crimped to eliminate bristle "fall out" Use with acid, flux and pipe dope 1/2" Acid
More informationCut Off and Deburring
Cut Off and Deburring Cut Off and Deburring Heavy Duty Pipe Cutters Heavy-Duty Pipe Cutters RIDGID Heavy-Duty Pipe Cutters for fast, burr-free cutting of steel pipes up to. Extra-long shank protects adjustment
More informationQuicklub Lubrication Systems Fittings, Adapters and Accessories
Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for divider valve mounting (6, 8, 10 and
More informationTube Remover and Installer. and Installer Used for servicing Ford systems produced after Screen Extractor. Ford Aerostar Expansion
gauges A/C FLUSH KIT Easy-to-use system removes refrigerant oil, moisture contaminants from system components lines during retrofitting compressor replacement. Kit includes rubber-tipped flush gun, canister
More informationVISUAL INDEX Equipment
U R Hand Tube Benders Ratchet Hand Tube Bender 1 Hand Tube Bender BAV06/12 Combined Tube Bending & Cutting Tool BV06/18, BV20/25 Tube Bending Tools Benders R4-R5 R4 R5 R6 R6 Bender Capacity Guides Exactol
More informationTX115/215 Hot-tap Insertion Turbine Instructions
TX115/215 Hot-tap Insertion Turbine Instructions General Information These hot tap versions of the proven TX insertion flow sensors are designed to install or be serviced without depressurizing the pipe.
More informationSpecial Applications Require Special Tools
Index Routers.................. 102-103 Tappers..................... 104 Clinch Nut Tools.............. 106 Rivet Shavers................ 107 Skin Clamp Runners........... 108 Saws................... 109-110
More information4405-RA 4405-R 4405-RA 4405-R S
ACCESSORIES Page 34 Master Parts Breakdowns Updated Feb. 1st 2006 Master Parts Breakdowns Updated Feb. 1st 2006 Page 35 This tool is designed to operate on 90 psig (6.2 bar) maximum air pressure with 1/4
More informationTX101/201 Insertion Turbine Instructions
TX101/201 Insertion Turbine Instructions General Information Sapphire bearings and a non-drag pick-off give these adjustable insertion turbine flow sensors a wide flow and long life. A Hall-effect device
More informationDRILLS. Parts Interchangeability. Precision Parts. Ultimate Ergonomics
DRILLS Dotco drills are used daily in applications ranging from aerospace to oil fields and refineries. Three styles are available - pistol grip, inline, and right angle models. in this section range from
More informationOutput 0.9 H.P. (675 W) 9000 to R.P.M (11000rpm is standard)
HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual COLLET SPINDLE SHOWN Model Number Exhaust Direction Throttle Type 44RAE Side (L) Lever or (K) Safety Lever Speed 9000 to 11000
More informationAiretool. Gas Line Cleaners Range: 3/4 (19.05mm) to 1-1/2 (38.10mm) Operating & Service Manual PL EN 10/01/2015
Operating & Service Manual PL9-6026EN 0/0/205 Airetool Gas Line Cleaners Range: 3/4 (9.05mm) to -/2 (38.0mm) For additional product information visit our website at http://www.apextoolgroup.com PL9-6026EN
More informationM-B Companies, Inc. Specification. Model 245. Self Propelled Intermediate Striper. High Pressure Airless. Options. Revised September 27, 2006
M-B Companies, Inc. Administration Pavement Marking Equipment Divisions 1615 Wisconsin Avenue EAST COAST DIVISION WEST COAST DIVISION P.O. Box 200 79 Montgomery Street 2490 Ewald S.E. New Holstein, WI
More informationQuicklub Lubrication Systems
Fittings, Adapters and Accessories Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for
More informationDIAMOND CONCRETE SAW PARTS LIST MODEL CC8000 P R O D U C T S. (Revised )
DIAMOND P R O D U C T S CONCRETE SAW PARTS LIST MODEL CC8000 (Revised 10-15-2002) Table of Contents Page Saw Controls Legend. 3 Drawing 1. Frame Group. 4-5 Drawing 2. Arm Assembly... 6-7 Drawing 3. Hydraulics
More informationSTANDARD SERIES VALVE SEAT CUTTERS (for use with standard series pilots,.375" top)
PA R T S L I S T STANDARD SERIES VALVE SEAT S (for use with standard series pilots,.375" top) 28.6mm 1-1/8" 31.8mm 1-1/4" 35mm 1-3/8"! OF 15 3 250 243 30 3 250 278 30 3 253 299 30 x 45 3/3 250 274 45 3
More informationMillennium TM. 100 thru 675 Tons (315 thru 2375 kw) renewal parts. Supersedes: RP1 (1099) Form RP1 (710) R-22 and R-134a 00202VIP
Millennium TM Rotary Screw Liquid Chillers renewal parts Supersedes: 160.80-RP1 (1099) Form 160.80-RP1 (710) Model YS BA CB S0 thru YS FA FB S5 (Style E) 100 thru 675 Tons (315 thru 2375 kw) 00202VIP R-22
More informationSanders, Buffers & Polishers Introduction
Sanders, Buffers & Polishers Introduction Dotco sanders, buffers and polishers are available in a variety of styles and power ratings to provide flexibility in choosing the best tool for the job. Disc
More informationILLUSTRATED PARTS LIST
CW413 / TW413 WITH 390cc HONDA ENGINE 00-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 390cc
More information855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
More informationTX 115/215 Hot-tap Insertion Turbine Instructions
TX 115/215 Hot-tap Insertion Turbine Instructions General Information These hot tap versions of the proven TX insertion flow sensors are designed to install or be serviced without depressurizing the pipe.
More informationTX101/201 Insertion Turbine Instructions
TX101/201 Insertion Turbine Instructions General Information Ruby bearings and a non-drag pick-off give these adjustable insertion turbine flow sensors a wide flow and long life. A sensor detects the passage
More informationGROUP 3 HYDRAULICS 636 EXTENDO PARTS BOOK
GROUP 3 HYDRAULICS 636 EXTENDO ELECTRICAL SCHEMATIC FOR 636 & 5528, AL-11969... 3-4 ELECTRICAL PLUG-INS SCHEMATIC, BL-10012... 3-7 HYDRAULIC SCHEMATIC, AL-11355... 3-8 HYDRAULIC SCHEMATIC WITH OPTIONAL
More informationModel & AP (Air Purge) Condenser Cleaner
TM-81 October 13, 2004 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders tube rolling motors
More informationPneumatic Connector, Tubing, and Accessory Catalog
Pneumatic Connector, Tubing, and Accessory Catalog Pneumatic Quick Connectors Plastic Tubing and Adaptors Tube Connectors and Manifolds Plumbing Tools Contents Plastic Tubing 1 Plastic Tubing Specifications
More informationOne Direct Source for all your Water Blasting Parts and Accessories!
table of contents One Direct Source for all your Water Blasting Parts and Accessories! SURFACE NOZZLES PAGE Drilled Nozzles 1 Standard Button Tip Flex Lance Nozzles 1 TLX Nozzle 1 Drilled Nozzle Flow Charts
More informationInternal Pressure Pipe Cutters. Manual E540
Internal Pressure Pipe Cutters Manual E540 Contents Logan Internal Pressure Pipe Cutters Overview...2 Uses...2 Construction...2 Tool Illustration...3 Operation...2 Single Cut from a Fixed Platform... 2
More informationMicrobore Hose, Assemblies & accessories
bar DN2 and DN4 High pressure Microbore hose Technical data Microbore hose The microbore hose assembly, most commonly used to connect to a Minimess test point for pressure testing, has many other diverse
More informationQuicklub Lubrication Systems Fittings, Adapters and Accessories
Divider Valve Mounting Accessories 24646 Valve mounting bracket 5304 4" nylon locknut for valve mounting 247023 Grade 8, 4" valve mounting bolt 239499 Template for divider valve mounting (6, 8, 0 and 2
More informationQGD-20/25/30 & QGD-40/50
QGD-0/5/0 & QGD-40/50 Direct Drive Rotary Screw Air Compressor Parts Manual This manual contains important safety information and should be made available to all personnel who operate and/or maintain this
More informationAIR DRIVEN TUBE CLEANER
MODEL PGX-2 AIR DRIVEN TUBE CLEANER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 5/11/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C.
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More informationA M Supply Co. Hand Tools Metal Cutting. Metal Cutting. Lenox Seamers. Snips. Milwaukee Snip Sets. Snips. Phone:(405) (800)
Metal Cutting Lenox Seamers Part # L22210 Description 3" Seamer Snips Metal Cutting Milwaukee Snip Sets Part # Description Cut Cap Sheet Metal Cut Cap Stainless L22101 Aviation Snip Left 18 ga 22 ga L22102
More informationPARTS LIST. Reproduction. Not for. Models Mfg. No. Description Pico 6, SP 44cm Walk Behind, CE (2010)
PARTS LIST Models Mfg. No. Description 884142 Pico 6, SP 44cm Walk Behind, CE (2010) Manual Part No. 1739809 Revision B Rev. Date: 1/13/2011 Table Of Contents PRODUCT COMPONENTS PAGES Handle, Controls
More informationMODELS JG43, JG63, JG83 JG44, JG64, JG84
MODEL J STYLE G HERMETIC COMPRESSORS RENEWAL PARTS Supersedes: 180.23-RP4 (695) Form 180.23-RP4 (1298) MODELS JG43, JG63, JG83 JG44, JG64, JG84 (See Page 2 for Complete Model Nomenclature) 27531A UNIT
More information767 Hydraulic Hand Pump
INSTRUCTION MANUAL 767 Hydraulic Hand Pump Serial Code ABM Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
More informationELECTRICAL COMPONENTS
ELECTRICAL COMPONENTS Part No. Part Name Qty Part No. Part Name Qty 301461 Electrical box 1 716558 Coolant on/off button 1 301462 Connector 24 volt 1 716540 Start button (green) 1 301795 Overload 1 716539
More informationCopper Sleeve, Unit Injector, Replacement
Volvo Trucks North America Greensboro, NC USA This service bulletin replaces SB 237-46, Copper Sleeve, Unit Injector, Replacement dated 6.2007, publication no. PV776-20177417. DService Bulletin Trucks
More informationLubrication Installation Components, Accessories & Fittings Table of Contents
Lubrication Installation Components, Accessories & Fittings Table of Contents Lubrication Fittings & Accessories: Introduction............................................. 2 Threaded Fittings........................................
More informationHYDRAULIC PUMPS. Performance under Pressure
HYDRAULIC PUMPS LARZEP Pumps are available in a wide range of models: Hand pumps, Air hydraulic pumps, Modular pumps, Manual, Electric, Air and Petrol hydraulic powerpacks, Split-Flow powerpacks, Hydrotest
More informationTECHNICAL DATA OBSOLETE
August 31, 2006 Check Valve 815a 1. PRODUCT NAME Viking Easy Riser Swing Check Valve Model E-1: Available since 1992 Model F-1: Available since 1994 2. MANUFACTURER The Viking Corporation 210 N. Industrial
More informationMK-5000G exploded VieW
Frame accessories 38 cutting head Pump Assembly 39 connecting linkage foot pedal linkage 40 curtain blade guard 41 ENGINE Assembly 42 PARTS LIST A Frames - - A1 Frame, MK-5000 Main 1 155541 B Pivot Bracket
More informationMueller 300 Ball Valves Industry-leading 300psi low lead ball valves
Mueller 300 Ball Valves Industry-leading 300psi low lead ball valves Mueller 300 Ball Valves Your assurance of quality, dependable ball valves The ball valve designed for 300 psig working pressure Before
More informationTech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800)
SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.hytec.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Parts
More informationForm No Parts List for: MODEL B HYDRAULIC PUMP GENERAL SECTION PG PG553-2UK FT600 PG554. PG120A Series Y70G Series. Sheet No.
MODEL B HYDRAULIC PUMP GENERAL SECTION Parts List for: Form No. 100520 60208 PG553 65820 PG553-2UK FT600 PG554 FT700-001 PG554-LEAD FT700-002 PG554-2UK PG55A Series Y26G Series PG90A Series Y60G Series
More informationSERIES 36-AM & BD...4-5 SERIES 36-AM-RA & BD RA...6-7 SERIES 50-AM & BD...8-9 SERIES 36 TOOL CHANGER...10-11 SERIES 50-TOOL CHANGER...12-13 SERVO MOTOR ADAPTERS...14-15...16-17...18-19 COLLET NUT...19
More informationILLUSTRATED PARTS LIST
BD300 WITH 277cc KOHLER ENGINE 00-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 277cc 2 WHEEL
More informationU1 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 060-064 - 130-134 - 133-U1 PUMP PARTS PRICE LIST DESCRIPTION QTY. PER PUMP 060-U1 Pump Body 1 See Note 1 1 060-U1 Pump Body with Flush 1 See Note 1 1 064-U1 Rectangular Flange Inlet Body 1
More informationFire Protection. FP-XA End Suction
Fire Protection FP-XA End Suction PRODUCT BULLETIN MODEL FP-XA END SUCTION CPS Model FP-XA End Suction pumps are used in a variety of fire fighting applications. These rugged and efficient centrifugal
More informationTAPS & DIES S.T.I. TAPS - HIGH SPEED GROUND MACHINE SCREW SIZES FRACTIONAL SIZES
S.T.I. TAPS - HIGH SPEED GROUND High quality tap S.T.I. taps are oversize to rethread damaged threads Available in plug and bottoming style only MACHINE SCREW SIZES Plug Bottom Nominal H # of Thread Overall
More informationSUPER TUBE-TUGGER Continuous Tube Extractor For 1-1/2 2 Tube OD ( )
www.elliott-tool.com TM-42 Rev. 9/20/04 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders
More informationQuality Value Assurance
Pump Selection Guide Quality Value Assurance In the beginning From it s inception in 1990 with one man in a service van, to the industry leader in innovative dairy solutions that DariTech is today, we
More informationILLUSTRATED PARTS LIST
CW300 WITH 265cc SUBARU ENGINE 800-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed on the driver side. 265cc 2
More informationAiretool. CC-325-HP High Pressure Water Flush Condenser Tube Cleaner. Operating & Service Manual IM 05/11/2011
Operating & Service Manual 90093-IM 05/11/2011 Airetool CC-325-HP High Pressure Water Flush Condenser Tube Cleaner For additional product information visit our website at http://www.apextoolgroup.com Safety
More information2015 PRODUCTS & PRICES
2015 PRODUCTS & PRICES STOPS THAT ARE USER FRIENDLY Orders 1-800-821-3491 Phone 1-717-484-0230 Fax 1-717-484-0933 E-mail mayaposi@att.net Web mayaposi-stop.com MAYA POSITIONING EQUIPMENT MFG CO. INC. 940
More informationHigh Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
More informationIndex. Butterfly Valves
Dry Bulk - Chemical - Petroleum Dry Bulk - Chemical - Petroleum Nozzles Nozzles & Valves & Index Index Part No. Description Page Nozzles P- 202 Overwing Aircraft Refueling, Bronze 1 P- 2022 Overwing Aircraft
More informationInstallation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware
More informationTable of Contents. Standard Taps
Table of Contents Standard Taps Standard Taps--High Speed Steel Machine Screw Sizes... 3 Standard Taps--High Speed Steel Hand Taps (Fractional Sizes)... 5 Standard Taps--High Speed Steel Machine Screw
More informationAdvanced Artillery For Enhanced Tubes
Advanced Artillery For Enhanced Tubes BRUSHES DESIGNED TO CLEAN THE INTERNAL LANDS & GROOVES Brushes for internally enhanced tubes Available in Bags of 25 Tube O.D., I.D., & Gauge (B.W.G.) A Tube O.D.
More informationEasy Riser swing check valve Models E-1 & F-1
Page 1 of 7 1. DESCRIPTION The Viking Easy Riser Swing Check Valve is a general purpose rubber-faced approved for use in fire service systems. The valve is for use in wet system risers, preaction system
More informationGeneral Safety and Maintenance Manual. Output. Type 0.9 H.P.675 W. (L) Lever or (K) Safety Lever R.P.M. (18000PM is standard)
HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual SUPER EXTENDED LENGTH DIE GRINDER FEATURING FRONT END DOUBLE ROW BEARINGS FOR SUPPORT. Multiple accessory mounting is possible
More informationU1 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 PUMP 030-U1 Pump Body 1 See Note 1 1 030-U1 Pump Body with Flush 1 See Note 1 1 034-U1 Rectangular Flange Inlet Body 1 See Note 1 1 034-U1 Rect. Flange Inlet Body with Flush 1 See Note 1 1
More informationRegenerative Turbine Pumps
Bulletin 40 October 008 40 40 80 80 Series Regenerative Turbine Pumps Capacities to 60 GPM Heads to 800 Feet MTH PUMPS 40 40 80 80 Series regenerative turbine pumps represent the most economical, high
More informationModel SMA3-A SLUDGEMASTER
SERVICE AND OPERATING MANUAL Model SMA3-A SLUDGEMASTER PLEASE NOTE! The photos shown in this manual are for general instruction only. YOUR SPECIFIC MODEL MAY NOT BE SHOWN. Always refer to the parts list
More informationB/M No. B H00925 M /8-10T 3" B H00920 M /8-10T 2-1/2" Part Number. Item. No. 800B
Threaded Case (NPT), Packing Construction Page 80. Supersedes 03/0/ 87 8 B/M Mtg. Bracket Spline Ext. B00 4 H0095 M0454-3/8-0T 3" B5999 5 H0090 M07-3/8-0T -/" 7 Kit available for this model, P/N B778 for
More informationPARTS ORDERING INFORMATION
RP-268 REPAIR PARTS FOR VE268 Roll Grooving Tool PARTS ORDERING INFORMATION When ordering parts the following information is necessary for the Victaulic Tool Company to promptly process the order and send
More informationP O W E R P U M P S SECTION INDEX. Proper Size & Selection G1 Series Electric...
SECTION INDEX Proper Size & Selection... 44-45 G1 Series Electric... 46-47 2 Series Electric... 48-49 G3 Series Electric... 5-51 G4 Series Electric... 52-53 P O W E R P U M P S G5 Series Electric... 54-55
More informationService Guide. High-Pressure Grease Pump. 100 psi (6.8 bar) High-Pressure Pump Model 7785 Series Specifications
Description Service Guide 7785-A5 7785-B5 7785-MA The major components of the pump models in the 7785 series consist of an air-operated motor and a pump tube. The air motor connects directly to the double-acting
More informationForm No Parts List for: MODEL B ELECTRIC HYDRAULIC PUMP. Maximum Capacity: 10,000 PSI PE55TWP-IBT-115. Sheet No. 1 of 8
Parts List for: Form No. 1000457 PE55TWP-IBT-115 MODEL B ELECTRIC HYDRAULIC PUMP Maximum Capacity: 10,000 PSI 1 2 3 7 SPX Hydraulic Technologies, Rockford, IL 61109 USA www.powerteam.com Made in USA 309219Rev7
More informationBRASS FITTINGS and Related Products
Discount Hydraulic Hose.com Cat. BR602 February, 2006 Prices Subject to change BRASS FITTINGS and Related Products Air Brake Fittings: Nylon Tubing 2 Push-In Air Brake Fittings 4 Pre-Assembled Air Brake
More informationInline Pumps. Product review. Wilo-VeroLine-IPL. Single-head pumps: Single stage inline, flanged, long coupled, mechanical sealed dry rotor pump
Product review North America Duty charts 7 RPM - Hz - North America 9 IPL. 7 IPL IPL. IPL IPL. RPM - Hz - North America IPL. IPL IPL. IPL Single-head pumps: Single stage inline, flanged, long coupled,
More information8 to 10 threads chamfered for easy thread starting in tough material.
TAPER 8 to 10 threads chamfered for easy thread starting in tough material. NC = National Course NF = National Fine PLUG BOTTOM 3 to 5 threads chamfered for general use when tapping to bottom of hole is
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MODEL: VINTAGE (RH-5700) REV.A Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size -/8 Diameter Dimensions are in Inches and Approximation
More informationD-4070 Two Stage Pneumatic Actuator
FANs 268.1, 1628.3 Product/Techncial Bulletin D4070 Issue Date 1095 D-4070 Two Stage Pneumatic Actuator The D-4070 Two Stage Pneumatic Actuator is a multipurpose positioning device used to accurately position
More informationFeatures and Specifications for Impact Wrenches
Pneumatic Air Tools Version 2017 Revised 06/2017 Email your order to: sales@polyconn.com or fax to (763) 398-2590. www.polyconn.com. Questions call: (763)559-0388 3062 Ranchview Lane North. Plymouth, MN
More informationPrd List Part No. Description Cat Price
13023 KIT OIL RESERVOIR SERIES II J 55.00 13027 KIT FLUSHING (FITS H75-HXL20W) O 88.00 13989 OIL FLUSHING 1 GALLON O 26.50 13990 OIL FLUSHING CASE 4 GALLONS O 99.50 13996 OIL 20 WT 1 GAL. MASPORT O 28.50
More informationGRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL
GRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL Grain Carts KITS Thunderstone Manufacturing, LLC. 3400 West O Street Lincoln, NE 68528 402-435-4249 (Fax) 402-438-3918 www.thunderstonemfg.com Aluminum
More informationFORD - Cyl Block and Related Parts
FORD - Cyl Block and Related Parts Ref Description Qty All 302 Qty 351 Qty 351-HP 1 BLOCK ASSEMBLY 1 59-4046 1 59-4047 1 59-4047 2 PLUG - 1½ CUP - BRASS 6 59-4048 6 59-4048 6 59-4048 3 PLUG - OIL PASSAGE
More informationReproduction. Not for. 5.5GT 44cm CAST DECK SELF PROPELLED MOWER. Parts Manual for GT 44cm
Parts Manual for 5.5GT 44cm CAST DECK SELF PROPELLED MOWER Model No. Description 844189 5.5GT 44cm Briggs & Stratton Yard Power Products Group 535 Macon Road McDonough, GA, 30253 U.S.A. 800-935-2967 Manual
More informationAermotor 4 SUBMERSIBLE PUMPS 35, 50, 75, 90 GPM A+ SUPER SUB Series stainless steel
A+ SUPER SUB Series stainless steel The A+ Super Sub Series Stainless Steel 4 Submersible Pumps deliver efficient and dependable performance even in rough, aggressive water. Heads to 640 feet and capabilities
More information2018 High Performance Check Valves for liquid and gaseous media
2018 High Performance Check Valves for liquid and gaseous media Check valves Catalogue 45 Date: 04/2018 WEH - We Engineer Hightech All rights reserved, WEH GmbH 2018. Unauthorized copies are strictly forbidden
More informationIn-Line Positive Feed Tools
In-Line Positive Feed Tools ADVANCED DRILLING EQUIPMENT SP-1300-1-EN-0806-.25M 1-1 Introduction In-Line Positive Feed Tools How Positive Feed Drills Operate Our in-line positive feed drills use two interconnected
More informationMODEL B HYDRAULIC PUMP
< < SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031
More informationROTARY, STRAIGHT, PIPE & TUBE CLEANING TOOLS & NOZZLES
Nozzles ROTARY, STRAIGHT, PIPE & TUBE CLEANING TOOLS & Jetstream provides tools for different 15,000 psi applications in surface preparation, pipe cleaning and tube cleaning. All of our tools are made
More informationPart/Assy 7527 ECN Ref S000000
Parts List Description Exhaust Manifold,Side Outlet(*) Part/Assy 7527 ECN Ref S000000 SAP Item Illustration RTP RTS Part No Catalogue No / Description Qty ECN 0001 1 X X 36609 MANIFOLD, EXHAUST, 4 CYL,
More informationLow shear, low pulsation performance delivers superior finish quality
TRITON 3:1 irculating Pumps TRITON 13HP 23375 & 233751 TRITON 38HP 23385 & 233816 Low shear, low pulsation performance delivers superior finish quality FETURES ND ENEFITS Low pulsation output provides
More information