Metallized Polypropylene (PP) - Capacitors for DC-Link Applications. Capacitances from 1.0 mf to 400 mf. Rated Voltages from 400 VDC to 1300 VDC.

Transcription

1 WIM C-LINK MKP 4 Metallized Polypropylene (PP) - Capacitors for C-Link pplications. Capacitances from 1.0 mf to 400 mf. Rated Voltages from 400 VC to 1300 VC. Special Features Capacitances up to 400 mf High volume/capacitance ratio Excellent self-healing properties Very low dissipation factor High reliability 2- and 4- contact configuration (plate versions on request) EC-Q200 qualified ccording to RoHS 2011/65/EU Typical pplications s intermediate circuit capacitor e.g. in high power converter technology, power supplies, solar inverters etc. Construction ielectric: Polypropylene (PP) film Capacitor electrodes: Vacuum-deposited Internal construction: Plastic film Vacuum-deposited electrode Metal contact layer (schoopage) Termination Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Terminations: Tinned wire (plate versions on request). Marking: Colour: Red. Marking: Black. Epoxy resin seal: Red Electrical ata Capacitance range: 1 mf to 400 mf (intermediate values on request) Rated voltages: 400 VC, 500 VC, 600 VC, 800 VC, 900 VC, 1100 VC, 1300 VC Capacitance tolerances: ±20%, ±10%, ±5% Operating temperature range: 55+ C to C (hot spot including self-heating) Climatic test category: 55/085/56 in accordance with IEC issipation factors at +20 C: PCM 1 khz 10 khz x x x x x x 10-4 Voltage and current derating: derating factor of 1.35% per K must be applied from +85 C for C voltages and from +70 C for C currents (I rms ). dditionally a derating factor of 4.5% per K must be applied from +85 C for C currents (I rms ) Reliability: Operational life hours (U r and 70) C) Failure rate l 0 (0.5 x U r and 40) C) P = C N [mf] x U r [V] l 0 P < 2 fit < P < 5 fit < P < 10 fit < P < 20 fit P > < 30 fit Maximum pulse rise time: Insulation resistance at +20+ C: sec (M x mf) (mean value: sec) Measuring voltage: 100 V/1 min. Test voltage: 1.2 U r, 2sec ielectric absorption: 0.05 % Specific dissipation: Box size Specific dissipation in Watts per K W x H x L in mm above the ambient temperature 9 x 19 x x 21 x x 24 x x 26 x x 29 x x 15 x x 34.5 x x 39.5 x x 32 x x 39.5 x x 45.5 x x 46 x x 50 x x 55 x x 50 x x 55 x x 65 x Packing Packing units at the end of the catalogue For further details and graphs please refer to Technical Information. PCM max. pulse rise time V/msec at T < 40) C 400 VC 500 VC 600 VC 800 VC 900 VC 1100 VC 1300 VC for pulses equal to the rated voltage 119

2 WIM C-LINK MKP 4 Continuation General ata 400 VC (70 C) / 300 VC (85 C) Capacitance W H L PCM** Pin I S I rms *(10 khz)* ESR (10 khz)* Part number 1 mf CP4G CP4G CP4G CP4G CP4G CP4G mf / CP4G051006B / CP4G / CP4G052006F / CP4G052506G / CP4G053006I / CP4G054006J / CP4G055007G / CP4G056007G / CP4G057007H / CP4G058007H / CP4G059007H 100 mf / CP4G061007I / CP4G061207I / CP4G061407J / CP4G061507J / CP4G061607K / CP4G061807K / CP4G061907K / CP4G062007K CP4G062209F CP4G062509H CP4G062709H CP4G063009H CP4G063309J CP4G063509J CP4G063709J CP4G064009J New voltage range * General guide * Permissible I rms at 10 C internal temperature rise (general guide) 2- version PCM d ** PCM = Printed circuit module = spacing ims. in mm. Part number completion: Version code: 2- = 2 4- = 4 Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Pin length: 6-2 = S Taped version see page 145. Rights reserved to amend design data without prior notification. 4- verion c c W PCM b d c Continuation page

3 WIM C-LINK MKP 4 Continuation General ata 500 VC (70 C) / 400 VC (85 C) Capacitance W H L PCM** Pin I S I rms *(10 khz)* ESR (10 khz)* Part number 1 mf CP4H CP4H CP4H CP4H / CP4H147006B / CP4H mf / CP4H / CP4H151206F / CP4H151506G / CP4H152006I / CP4H152206J / CP4H152506J / CP4H153007G / CP4H153507G / CP4H154007G / CP4H154007H / CP4H154507H / CP4H155007H / CP4H155507H / CP4H156007I / CP4H156507I / CP4H157007I / CP4H157507I / CP4H158007I / CP4H158507J / CP4H159007J / CP4H159507J 100 mf / CP4H161007J CP4H161009F / CP4H161107K CP4H161109F / CP4H161207K CP4H161209F / CP4H161307K CP4H161309F CP4H161409F CP4H161509F CP4H161609H CP4H161709H CP4H161809H CP4H161909H CP4H162009H CP4H162109H CP4H162209J CP4H162409J New voltage range * General guide * Permissible I rms at 10 C internal temperature rise (general guide) ** PCM = Printed circuit module = spacing ims. in mm. Rights reserved to amend design data without prior notification. Continuation page

4 WIM C-LINK MKP 4 Continuation General ata 600 VC (70 C) / 450 VC (85 C) Capacitance W H L PCM** Pin I S I rms (10 khz)* ESR (10 khz)* Part number 2 mf CP4I / CP4I / CP4I047006F 10 mf / CP4I051006G / CP4I051007M / CP4I051506I / CP4I052006J / CP4I052007G / CP4I052507G / CP4I053007H / CP4I053507H / CP4I054007I / CP4I054507I / CP4I055007J / CP4I055507J / CP4I056007J / CP4I056507K CP4I056509F / CP4I057007K CP4I057009F / CP4I057507K CP4I057509F / CP4I058007K CP4I058009F CP4I058509F CP4I059009F CP4I059509H 100 mf CP4I061009H CP4I061109H CP4I061159J CP4I061209J CP4I061309J CP4I061409J CP4I061509J * General guide 2- version ** PCM = Printed circuit module = spacing PCM d ims. in mm. Part number completion: Version code: 2- = 2 4- = 4 Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Pin length: 6-2 = S Taped version see page 145. Rights reserved to amend design data without prior notification. 4- version c c W PCM b d c Continuation page 123

5 WIM C-LINK MKP 4 Continuation General ata 800 VC (70 C) / 700 VC (85 C) Capacitance W H L PCM** Pin I S I rms (10 khz)* ESR (10 khz)* Part number 2 mf CP4L / CP4L / CP4L047006G 10 mf / CP4L051006I / CP4L051506J / CP4L051507G / CP4L052007G / CP4L052507H / CP4L053007H / CP4L053507I / CP4L054007I / CP4L054507J / CP4L055007J / CP4L055507K CP4L055509F / CP4L056007K CP4L056009F CP4L056509F CP4L057009H CP4L057509H CP4L058009H CP4L058509J CP4L059009J CP4L059509J 100 mf CP4L061009J CP4L061109J CP4L061159J 900 VC (70 C) / 760 VC (85 C) Capacitance W H L PCM** Pin I S I rms (10 khz)* ESR (10 khz)* Part number 2 mf / CP4N042006B / CP4N045006G / CP4N047006I 10 mf / CP4N051006J / CP4N051007G / CP4N051507G / CP4N052007H / CP4N052507I / CP4N053007I / CP4N053507J / CP4N054007K CP4N054009F CP4N054509F CP4N055009F CP4N055509F CP4N055509H CP4N056009H CP4N056509H CP4N057009J CP4N057509J CP4N058009J * General guide ** PCM = Printed circuit module = spacing ims. in mm. Rights reserved to amend design data without prior notification. Continuation page

6 WIM C-LINK MKP 4 Continuation General ata 1100 VC (70 C) / 920 VC (85 C) Capacitance W H L PCM** Pin I S I rms (10 khz)* ESR (10 khz)* Part number 2 mf / CP4P / CP4P043006F / CP4P045006I / CP4P047006J / CP4P047007F 10 mf / CP4P051007G / CP4P051507I / CP4P052007I / CP4P052007J / CP4P052507K CP4P053009F CP4P053509F CP4P054009H CP4P054509H CP4P055009J CP4P055509J CP4P056009J 1300 VC (70 C) / 1100 VC (85 C) Capacitance W H L PCM** Pin I S I rms (10 khz)* ESR (10 khz)* Part number 2 mf / CP4R242006F / CP4R245006J / CP4R245007G / CP4R247007G 10 mf / ,2 CP4R251007H / CP4R251507I / CP4R252007K CP4R252009F CP4R252509F CP4R253009H CP4R253509J CP4R254009J * General guide 2- version ** PCM = Printed circuit module = spacing PCM d ims. in mm. Part number completion: Version code: 2- = 2 4- = 4 Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Pin length: 6-2 = S Taped version see page version c c W PCM b d c Rights reserved to amend design data without prior notification. 124

7 Recommendation for Processing and pplication of Through-Hole Capacitors Soldering Process Internal temperature of the capacitor must be kept as follows: Polyester: preheating: T max. T 125 C soldering: T max. T 135 C Polypropylene: preheating: T max. T 100 C soldering: T max. T 110 C Single wave soldering Soldering bath temperature: T P 260 C well time: t P 5 sec ouble wave soldering Soldering bath temperature: T P 260 C well time: St P 5 sec ue to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. WIM Quality and Environmental Philosophy ISO 9001:2008 Certification ISO 9001:2008 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2008 of our factories by the infaz (Institut für uditierung und Zertifizierung) certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIM WPCS The WIM Process Control System (WPCS) is a quality surveillance and optimization system developed by WIM. WPCS is a major part of the quality-oriented WIM production. Points of application during production process: incoming material inspection metallization film inspection schoopage pre-healing attachment cast resin preparation/ encapsulation 100% final inspection Testing as per customer requirements WIM Environmental Policy ll WIM capacitors, irrespective of whether through-hole devices or SM, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. Lead PBB/PBE PCB rsenic CFC Cadmium Hydrocarbon chloride Mercury Chromium 6+ etc. We merely use pure, recyclable materials for packing our components, such as: carton cardboard adhesive tape made of paper polystyrene We almost completely refrain from using packing materials such as: foamed polystyrene (Styropor ) adhesive tapes made of plastic metal clips RoHS Compliance ccording to the RoHS irective 2011/65/EU certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, For the sake of the environment WIM has refraind from using such substances since years already. WIM Kondensatoren sind bleifrei konform RoHS 2011/65/EU WIM capacitors are lead free in accordance with RoHS 2011/65/EU Tape for lead-free WIM capacitors IN EN ISO 14001:2004 WIM s environmental management has been established in accordance with the guidelines of IN EN ISO 14001:2004 to optimize the production processes with regard to energy and resources. 15

8 P P P 1 H1 P 1 H t Typical imensions for Tag Configuration P 2 P Vh H1 P 1 W2 H W0 W1 iagram 1: PCM2.5/5/7.5mm W 0 F d P 0 d d F P 0 P 2 F P 2 P 0 iagram 2: PCM10/15mm iagram 3:PCM 22.5 and 27.5*mm *PCM 27.5 tag possible withtwo feed holesbetween components imensions for Radial Tag esignation Symbol PCM 2.5 tag PCM 5 tag PCM 7.5 tag PCM 10 tag* PCM 15 tag* PCM 22.5 tag PCM 27.5 tag Carrier tape width W 18.0 p p p p p p p0.5 Hold-down tape width W for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing for hot-sealing 12.0 adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape Hole position W p p p p p p p0.5 Hold-down tape position W to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. Feed hole diameter p p p p p p p0.2 Pitch of component P 12.7 p p p p p p1.5 3 * 8.1 p1.5 or 50.8 p1.5 cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch Feed hole pitch P p0.3 error max p0.3 error max p0.3 error max p0.3 error max p0.3 error max p0.3 error max p0.3 error max. 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch Feed hole centre to Hole centre to component centre P p p p p p p p0.7 P p p p p p p p1.3 Feed hole centre to bottom 16.5 p p p p p p p0.5 H edge of the component 18.5 p p p p p p p0.5 Feed hole centre to top H+H H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 edge of the component max max to to to to to 45.0 Pin spacing at F 2.5 p p p p p p0.8 upper edge of carrier tape 0.2 Pin diameter d 0.4 p p p0.05 or ,06 +0,08 +0, p0.05 or Component alignment h p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. Total tape thickness t 0.7 p p p p p p p0.2 Package (see also page 146) ROLL/MMO Unit see details page 147. ims in mm. iameter of s see General ata. REEL P 360 max. 52 p2 depending on P 30 p1 B 58 p2 comp. dimensions * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible REEL P 360 max. B P 30 p1 MMO 52 p2 54 p2 depending P 500 max. 58 p2 or REEL B 60 p2 on PCM and P 25 p1 66 p2 68 p2 component dimensions Please clarify customer-specific deviations with the manufacturer. 145

9 Types of Tape Packaging of Capacitors for utomatic Radial Insertion ROLL Packaging MMO Packaging REEL Packaging 340 max. 370 max. 30± 1 25± max. 500 max. 50 max. 70 max. 340 max. 490 max. BR COE (Labelling) Labelling of package units in plain text and with alphanumerical Bar Code Scanner decoding of WIM supplier number Customer s P/O number Customer s part number WIM confirmation number WIM part number Lot number ate code Quantity In addition part description of article capacitance value rated voltage dimensions capacitance tolerance packing as well as gross weight and customer s name are indicated in plain text. BRCOE Code max. 340 max. 50 max. B 146

10 Packing Quantities for Capacitors with Radial Pins in PCM 2.5 mm to 22.5 mm PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm pcs. per packing unit Size ROLL REEL MMO bulk P 360 P x x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 W H L Codes S N O F I H J C B B C E F B C E F G H I J K L M N B C E F G F C FB F G H I B FC C F FE F FF H J FG M B FH F FI 570* G 594* H 594* I 561* FJ 480* * TPS (Tray-Packing-System). Plate versions may have different packing units. Moulded versions. Rights reserved to amend design data without prior notification. Samples and pre-production needs on request. 147

11 Packing Quantities for Capacitors with Radial Pins in PCM 27.5 mm to 52.5 mm PCM 27.5 mm 37.5 mm 48.5 mm 52.5 mm pcs. per packing unit Size ROLL REEL MMO bulk P 360 P x x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 W H L Codes S N O F I H J C B * 460/340* B 459* 380/280* * FK 405* F 324* FL 324* G 198* I 198* FM 162* J 162* * B 357* C 294* * E 154* F 140* G 126* H 112* I 84* J 35* K 28* * E 80* H 84* J 25* L 25* * E 60* F 25* H 20* J 20* * for 2-inch transport pitches. Moulded versions. Rights reserved to amend design data without prior notification. * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. Updated data on 148

12 WIM Part Number System WIM part number consists of 18 digits and is composed as follows: Field 1-4: Type description Field 5-6: Rated voltage Field 7-10: Capacitance Field 11-12: Size and PCM Field 13-14: Version code (e.g. Snubber versions) Field 15: Capacitance tolerance Field 16: Packing Field 17-18: Pin length (untaped) M K S 2 C M S S MKS 2 63 VC 0.01 mf 2.5 x 6.5 x % bulk 6-2 Type description: Rated voltage: Capacitance: Size: Tolerance: SM-PET = SMT 50 VC = B0 22 pf = x 3.3 x 3 Size 1812 = K ±20 % = M SM-PEN = SMN 63 VC = C0 47 pf = x 3.3 x 4 Size 1812 = KB ±10 % = K SM-PPS = SMI 100 VC = pf = x 5.1 x 3.5 Size 2220 = Q ±5 % = J FKP 02 = FKP0 250 VC = F0 150 pf = x 5.1 x 4.5 Size 2220 = QB ±2.5 % = H MKS 02 = MKS0 400 VC = G0 220 pf = x 6.1 x 3 Size 2824 = T ±1 % = E FKS 2 = FKS2 450 VC = H0 330 pf = x 6.1 x 5 Size 2824 = TB... FKP 2 = FKP2 520 VC = H2 470 pf = x 7.6 x 5 Size 4030 = V FKS 3 = FKS3 600 VC = I0 680 pf = x 10.2 x 6 Size 5040 = X FKP 3 = FKP VC = J pf = x 13.7 x 7 Size 6054 = Y Packing: MKS 2 = MKS2 700 VC = K pf = x 7 x 4.6 PCM 2.5 = 0B MMO H x 340 = MKP 2 = MKP2 800 VC = L pf = x 7.5 x 4.6 PCM 2.5 = 0C MMO H x 370 = B MKS 4 = MKS4 850 VC = M pf = x 6.5 x 7.2 PCM 5 = 1 MMO H x 340 = C MKP 4C = MKPC 900 VC = N pf = x 7.5 x 7.2 PCM 5 = 1B MMO H x 370 = MKP 4 = MKP VC = O pf = x 7 x 10 PCM 7.5 = 2 REEL H = F MKP 10 = MKP VC = P mf = x 8.5 x 10 PCM 7.5 = 2B REEL H = H FKP 1 = FKP VC = Q mf = x 9 x 13 PCM 10 = 3 REEL H = I MKP-X2 = MKX VC = R mf = x 9 x 13 PCM 10 = 3C REEL H = J MKP-X1 R = MKX VC = S0 0.1 mf = x 11 x 18 PCM 15 = 4B ROLL H16.5 = N MKP-Y2 = MKY VC = T mf = x 12.5 x 18 PCM 15 = 4C ROLL H18.5 = O MP 3-X2 = MPX VC = U mf = x 14 x 26.5 PCM 22.5 = 5 BLISTER W = P MP 3-X1 = MPX VC = V0 1 mf = x 15 x 26.5 PCM 22.5 = 5B BLISTER W = Q MP 3-Y2 = MPY VC = W0 2.2 mf = x 19 x 31.5 PCM 27.5 = 6 BLISTER W = R MP 3R-Y2 = MPRY 4000 VC = X0 4.7 mf = x21 x 31.5 PCM 27.5 = 6B BLISTER W = T MKP 4F = MKPF 6000 VC = Y0 10 mf = x 19 x 41.5 PCM 37.5 = 7 Bulk/TPS Standard = S Snubber MKP = SNMP 250 VC = 0W 22 mf = x 22 x 41.5 PCM 37.5 = 7B... Snubber FKP = SNFP 275 VC = 1W 47 mf = x 31 x 56 PCM 48.5 = 8 GTO MKP = GTOM 300 VC = 2W 100 mf = x 45 x 57 PCM 52.5 = 9 C-LINK MKP 3 = CP3 305 VC = W 220 mf = C-LINK MKP 4 = CP4 350 VC = BW 1000 mf = 7100 C-LINK MKP 4S = CPS 440 VC = 4W 1500 mf = 7150 C-LINK MKP 5 = CP5 500 VC = 5W... Version code: Pin length (untaped) C-LINK MKP 6 = CP6... Standard = ±0.5 = C9 C-LINK HC = CHC Version 1 = = S C-LINK HY = CHY Version = 1B 16 ±1 = P1 Version 2 = Pin length (taped) none = 00 The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIM range. 143