WIMA MP 3-Y2. Metallized Paper (MP) RFI-Capacitors Class Y2 PCM 10 mm and 15 mm. Typical Applications. Construction. Packing.

Transcription

1 WIMA MP 3-Y2 Metallized Paper (MP) RFI-Capacitors Class Y2 PCM 10 mm and 15 mm Special Features Particularly high reliability against active and passive flammability Excellent self-healing as well as high voltage strength High degree of interference suppression due to good attenuation and low ESR For temperatures up to +110 C According to RoHS 2011/65/EU Typical Applications Class Y2 RFI applications to meet EMC regulations Capacitors connected to the mains between phase or neutral and earthed casing By-passing of the basic or supplementary insulation, pulse peak voltage T 5 kv Construction ielectric: Paper, epoxy resin impregnated Capacitor electrodes: Vacuum-deposited Internal construction: Capacitor paper Vacuum-deposited electrode Metal contact layer (schoopage) Terminating wire Encapsulation: Self-extinguishing epoxy resin, UL 94 V-0. metal foil Terminations: Tinned wire. Marking: Marking: Black on Silver. Electrical ata Capacitance range: 1000 pf to mf (E12-values on request) Rated voltage: 250 VAC Continuous C voltage* (general guide): 1000 V Capacitance tolerances: ±20% Operating temperature range: 40) C to +110) C Climatic test category: 40/110/56/C in accordance with IEC Insulation resistance at +20+ C: 12 x 10 3 M Measuring voltage: 100 V/1 min. issipation factors: tan d T 13 x 10 3 at 1 khz and +20+ C Approvals: Country Authority Specification Symbol Approval-No. Germany VE IEC /3 E USA/Canada UL UL E CAN/CSA-E Mechanical Tests Pull test on pins: 10 N in direction of pins according to IEC Vibration: 6 hours at Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC Low air density: 1kPa = 10 mbar in accordance with IEC Bump test: 4000 bumps at 390 m/sec 2 in accordance with IEC * If safety-approved EMI suppression capacitors are operated with a C voltage being above the specified AC voltage rating the given approvals are no longer valid (IEC ). Furthermore the permissible pulse rise time du/dt (F max.) will be subject to a reduction according to F max. = F r x 2 x UAC / UC if the C operating voltage UC is higher than 2 x UAC Test specifications: In accordance with IEC Maximum pulse rise time: Capacitance Pulse rise time V/msec pf/mf max. operation for pulses equal to a voltage amplitude with 2 x 250 VAC = 355 V according to IEC Test voltage: 2700 VC, 2 sec. Reliability: Operational life hours Failure rate 1 fit (0.5 x U r and 40) C) V EN Packing Available taped and reeled. etailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information. 93

2 WIMA MP 3-Y2 Continuation General ata Capacitance 250 VAC* W H L PCM** Part number 1000 pf MPY20W1100FA MPY20W1150FA MPY20W1220FA MPY20W1330FA MPY20W1470FB MPY20W1680FC mf MPY20W2100FC MPY20W2150F MPY20W2220FE00 * f = 50/60 Hz ** PCM = Printed circuit module = pin spacing Upon request with long pins 35-2 mm max. ims. in mm. Part number completion: Tolerance: 20 % = M Packing: bulk = S Pin length: 6-2 = S Taped version see page W L Z H pf pf pf pf PCM pf pf 0.01 µf d = 0.6 P if PCM 10 d = 0.8 P if PCM d PCM at the pin exit points ( ± 0.5) µf µf PCM f/mhz Impedance change with frequency (general guide) Rights reserved to amend design data without prior notification. 94

3 Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process Internal temperature of the capacitor must be kept as follows: Polyester: preheating: T max. T 125 C soldering: T max. T 135 C Polypropylene: preheating: T max. T 100 C soldering: T max. T 110 C Single wave soldering Soldering bath temperature: T P 260 C well time: t P 5 sec ouble wave soldering Soldering bath temperature: T P 260 C well time: St P 5 sec ue to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. WIMA Quality and Environmental Philosophy ISO 9001:2008 Certification ISO 9001:2008 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2008 of our factories by the VE inspectorate certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application of WPCS during production process: incoming material inspection metallization film inspection schoopage pre-healing pin attachment cast resin preparation/ encapsulation 100% final inspection Testing as per customer requirements WIMA Environmental Policy All WIMA capacitors, irrespective of whether through-hole devices or SM, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. Lead PBB/PBE PCB Arsenic CFC Cadmium Hydrocarbon chloride Mercury Chromium 6+ etc. We merely use pure, recyclable materials for packing our components, such as: carton cardboard adhesive tape made of paper polystyrene We almost completely refrain from using packing materials such as: foamed polystyrene (Styropor ) adhesive tapes made of plastic metal clips RoHS Compliance According to the RoHS irective 2011/65/EU certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, For the sake of the environment WIMA has refraind from using such substances since years already. WIMA Kondensatoren sind bleifrei konform RoHS 2011/65/EU WIMA capacitors are lead free in accordance with RoHS 2011/65/EU Tape for lead-free WIMA capacitors IN EN ISO 14001:2004 WIMA s environmental management has been established in accordance with the guidelines of IN EN ISO 14001:2004 to optimize the production processes with regard to energy and resources. 15

4 P P P 1 H1 P 1 H t Typical imensions for Taping Configuration P 2 P Vh H1 P 1 W2 H W0 W1 iagram 1: PCM2.5/5/7.5mm W 0 F d P 0 d d F P 0 P 2 F P 2 P 0 iagram 2: PCM10/15mm iagram 3:PCM 22.5 and 27.5*mm *PCM 27.5 taping possible withtwo feed holesbetween components imensions for Radial Taping esignation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping Carrier tape width W 18.0 p p p p p p p0.5 Hold-down tape width W for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing for hot-sealing 12.0 adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape Hole position W p p p p p p p0.5 Hold-down tape position W to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. Feed hole diameter p p p p p p p0.2 Pitch of component P 12.7 p p p p p p1.5 3 * 8.1 p1.5 or 50.8 p1.5 cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch Feed hole pitch P p0.3 error max p0.3 error max p0.3 error max p0.3 error max p0.3 error max p0.3 error max p0.3 error max. 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch Feed hole centre to pin Hole centre to component centre P p p p p p p p0.7 P p p p p p p p1.3 Feed hole centre to bottom 16.5 p p p p p p p0.5 H edge of the component 18.5 p p p p p p p0.5 Feed hole centre to top H+H H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 H+H component < H 1 edge of the component max max to to to to to 45.0 Pin spacing at F 2.5 p p p p p p0.8 upper edge of carrier tape 0.2 Pin diameter d 0.4 p p p0.05 or ,06 +0,08 +0, p0.05 or Component alignment h p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. Total tape thickness t 0.7 p p p p p p p0.2 Package (see also page 141) ROLL/AMMO Unit see details page 142. ims in mm. iameter of pins see General ata. REEL P 360 max. 52 p2 depending on P 30 p1 B 58 p2 comp. dimensions * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible REEL P 360 max. B P 30 p1 AMMO 52 p2 54 p2 depending P 500 max. 58 p2 or REEL B 60 p2 on PCM and P 25 p1 66 p2 68 p2 component dimensions Please clarify customer-specific deviations with the manufacturer. 140

5 Types of Tape Packaging of Capacitors for Automatic Radial Insertion ROLL Packaging AMMO Packaging REEL Packaging 340 max. 370 max. 30± 1 25± max. 500 max. 50 max. 70 max. 340 max. 490 max. BAR COE (Labelling) Labelling of package units in plain text and with alphanumerical Bar Code Scanner decoding of WIMA supplier number Customer s P/O number Customer s part number WIMA confirmation number WIMA part number Lot number ate code Quantity In addition part description of article capacitance value rated voltage dimensions capacitance tolerance packing as well as gross weight and customer s name are indicated in plain text. BARCOE Code max. 340 max. 50 max. B 141

6 Packing Quantities for Capacitors with Radial Pins in PCM 2.5 mm to 22.5 mm PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm pcs. per packing unit Size ROLL REEL AMMO bulk P 360 P x x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 W H L Codes S N O F I H J A C B B C E F A B C E F G H I J K L M N A B C E F G A FA C FB F G H I B FC C F FE F FF H J FG M A B FH F FI 540* G 680* H 680* I 680* FJ 450* * TPS (Tray-Packing-System). Plate versions may have different packing units. Moulded versions. Rights reserved to amend design data without prior notification. Samples and pre-production needs on request. 142

7 Packing Quantities for Capacitors with Radial Pins in PCM 27.5 mm to 52.5 mm PCM 27.5 mm 37.5 mm 48.5 mm 52.5 mm pcs. per packing unit Size ROLL REEL AMMO bulk P 360 P x x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 W H L Codes S N O F I H J A C B A 640* 460/340* B 544* 380/280* * FK 336* F 384* FL 288* G 176* I 176* FM 216* J 144* A 480* B 408* C 252* * E 132* F 108* G 108* H 84* M 100* I 72* J 35* K 28* * E 72* H 60* J 48* L 25* F 25* H 20* J 20* * for 2-inch transport pitches. Moulded versions. Rights reserved to amend design data without prior notification. * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. 143

8 WIMA Part Number System A WIMA part number consists of 18 digits and is composed as follows: Field 1-4: Type description Field 5-6: Rated voltage Field 7-10: Capacitance Field 11-12: Size and PCM Field 13-14: Version code (e.g. Snubber versions) Field 15: Capacitance tolerance Field 16: Packing Field 17-18: Pin length (untaped) M K S 2 C A 0 0 M S S MKS 2 63 VC 0.01 mf 2.5 x 6.5 x % bulk 6-2 Type description: Rated voltage: Capacitance: Size: Tolerance: SM-PET = SMT 50 VC = B0 22 pf = x 3.3 x 3 Size 1812 = KA ±20 % = M SM-PEN = SMN 63 VC = C0 47 pf = x 3.3 x 4 Size 1812 = KB ±10 % = K SM-PPS = SMI 100 VC = pf = x 5.1 x 3.5 Size 2220 = QA ±5 % = J FKP 02 = FKP0 250 VC = F0 150 pf = x 5.1 x 4.5 Size 2220 = QB ±2.5 % = H MKS 02 = MKS0 400 VC = G0 220 pf = x 6.1 x 3 Size 2824 = TA ±1 % = E FKS 2 = FKS2 450 VC = H0 330 pf = x 6.1 x 5 Size 2824 = TB... FKP 2 = FKP2 600 VC = I0 470 pf = x 7.6 x 5 Size 4030 = VA MKS 2 = MKS2 630 VC = J0 680 pf = x 10.2 x 6 Size 5040 = XA MKP 2 = MKP2 700 VC = K pf = x 13.7 x 7 Size 6054 = YA Packing: FKS 3 = FKS3 800 VC = L pf = x 7 x 4.6 PCM 2.5 = 0B AMMO H x 340 = A FKP 3 = FKP3 850 VC = M pf = x 7.5 x 4.6 PCM 2.5 = 0C AMMO H x 370 = B MKS 4 = MKS4 900 VC = N pf = x 6.5 x 7.2 PCM 5 = 1A AMMO H x 340 = C MKP 4 = MKP VC = O pf = x 7.5 x 7.2 PCM 5 = 1B AMMO H x 370 = MKP 10 = MKP VC = P pf = x 7 x 10 PCM 7.5 = 2A REEL H = F FKP 4 = FKP VC = Q mf = x 8.5 x 10 PCM 7.5 = 2B REEL H = H FKP 1 = FKP VC = R mf = x 9 x 13 PCM 10 = 3A REEL H = I MKP-X2 = MKX VC = S mf = x 9 x 13 PCM 10 = 3C REEL H = J MKP-X2 R = MKXR 1600 VC = T0 0.1 mf = x 11 x 18 PCM 15 = 4B ROLL H16.5 = N MKP-X1 R = MKX VC = U mf = x 12.5 x 18 PCM 15 = 4C ROLL H18.5 = O MKP-Y2 = MKY VC = V mf = x 14 x 26.5 PCM 22.5 = 5A BLISTER W = P MP 3-X2 = MPX VC = W0 1 mf = x 15 x 26.5 PCM 22.5 = 5B BLISTER W = Q MP 3-X1 = MPX VC = X0 2.2 mf = x 19 x 31.5 PCM 27.5 = 6A BLISTER W = R MP 3-Y2 = MPY VC = Y0 4.7 mf = x21 x 31.5 PCM 27.5 = 6B BLISTER W = T MP 3R-Y2 = MPRY 250 VAC = 0W 10 mf = x 19 x 41.5 PCM 37.5 = 7A Bulk/TPS Standard = S Snubber MKP = SNMP 275 VAC = 1W 22 mf = x 22 x 41.5 PCM 37.5 = 7B... Snubber FKP = SNFP 300 VAC = 2W 47 mf = x 31 x 56 PCM 48.5 = 8 GTO MKP = GTOM 305 VAC = AW 100 mf = x 50 x 57 PCM 52.5 = 9F C-LINK MKP 3 = CP3 400 VAC = 3W 220 mf = C-LINK MKP 4 = CP4 440 VAC = 4W 1000 mf = 7100 C-LINK MKP 4S = CPS 500 VAC = 5W 1500 mf = 7150 C-LINK MKP 5 = CP Version code: C-LINK MKP 6 = CP6 Standard = 00 Pin length (untaped) C-LINK HC = CHC Version A1 = 1A 3.5 ±0.5 = C9 Version A1.1.1 = 1B 6-2 = S Version A2 = 2A 16 ±1 = P The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIMA range. 138