technical data Systems FXMQ-MVE Conceiled ceiling unit (large)

Transcription

1 technical data Systems FXMQ-MVE Conceiled ceiling unit (large)

2 FXMQ-MVE 11 Concealed ceiling unit (large) 11 1 Features Specifications Technical specifications...3 Electrical specifications...4 Safety device settings Accessories Drain pump kit...6 High efficiency filter...8 Replacement long life filter Control systems Capacity tables Cooling capacity...12 Heating capacity Dimensions Dimensional drawings...16 Dimensional drawings with drain pump kit...18 Dimensional drawings with high efficiency filter/long life filter...20 Centre of gravity...21 Bolt pitch Piping Diagram Wiring Diagrams Sound level Fan characteristics Installation...28 Systems Indoor Units 217

3 1 Features Leaves maximum wall space for furniture and decoration Wide line-up to increase the flexibility in system designing: complete range of models ( kw) More than 150Pa external static pressure allows extensive ductwork runs and flexible application: ideal for use in large areas External static pressure can be easily adjusted using a change-over switch inside the electrical box to meet the resistance in the duct system Built-in drain pump (accessory) : housing the drain pump inside the unit has reduced the necessary installation space Indoor unit Drain pump kit 120 Min. 590 mm BUILT-IN DRAIN PUMP Min. 470 mm Indoor unit 40~80 type 200~250 type 100~125 type Systems Indoor Units

4 2 Specifications 2-1 Technical specifications FXMQ-MVE COOLING CAPACITY (1) kw HEATING CAPACITY (2) kw NOMINAL INPUT Cooling W ,294 1,465 Heating W ,294 1,465 DIMENSIONS HxWxD mm 390x720x x1,110x x1,380x1,100 WEIGHT kg CASING galvanised steel plate SOUND LEVEL Sound pressure 220V high dba low dba Sound power dba * * * * * FAN Air flow rate high m 3 /h 840 1,170 1,740 2,160 3,480 4,320 low m 3 /h ,380 1,740 3,000 3,720 Type sirocco fan Model D11/2D3AB1VE D11/2D3AA1VE 2D11/2D3AG1VE 2D11/2D3AF1VE D13/4G2DA1x2 Motor output W x380 External static pressure (50Hz) (Cf. note 4) Pa Drive direct drive HEAT EXCHANGER Rows x stages x fin pitch mm 3x16x2.0 3x26x2.0 Face area m AIR FILTER cf. note 5 REFRIGERANT CONTROL electronic expansion valve TEMPERATURE CONTROL microprocessor thermostat for cooling and heating PIPING CONNECTIONS Liquid flare mm ø 6.4 ø 9.5 ø 9.5 Gas mm ø 12.7 (flare) ø 15.9 (flare) ø 19.1 (brazing) Drain mm VP25, external diameter 32, internal diameter 25 PS1B SOUND ABSORBING INSULATION MATERIAL glass fiber ø 22.2 (brazing) 3D Nominal cooling capacities are based on: Indoor temperature: 27 CDB, 19 CWB Outdoor temperature: 35 CDB Equivalent refrigerant piping: 7.5m (horizontal) 2 Nominal heating capacities are based on: Indoor temperature: 20 CDB Outdoor temperature: 7 CDB, 6 CWB Equivalent refrigerant piping: 7.5m (horizontal) 3 Capacities are net including a deduction for cooling (an addition for heating) for indoor fan motor heat. 4 Static external pressure is changeable: change the connectors inside the electrical box, this pressure means: high static pressure - standard 5 The air filter is not a standard accessory, but please mount it in the duct system at the suction side. Select its colorimetric method (gravity method) 50% or more * Data were not available at the time of publication 2 Systems Indoor Units 219

5 FAN MOTOR THERMAL PROTECTOR C OFF: 135 ±8, ON: 87 ±15 3D034597B 2 Specifications 2-2 Electrical specifications FXMQ-MVE CURRENT Minimum circuit amps (MCA) A Maximum fuse amps (MFA) A 15 POWER SUPPLY VE 1 ~, 50Hz, V VOLTAGE RANGE Min~max V 198 ~ 264 INDOOR FAN MOTOR Fan motor rated output W x2 Full load amps (FLA) A D Voltage range: units are suitable for use on electrical systems where voltage supplied to unit terminals is not below or above listed range limits. 2 Maximum allowable voltage range variation between phases is 2%. 3 MCA/MFA: MCA = 1.25 x FLA MFA 4 x FLA next lower standard fuse rating minimum 15A. 4 Select wire size based on the MCA. 5 Instead of a fuse, use a circuit breaker 6 For more details concerning conditional connections, see select "Daikin Documentation" and select "conditional connection", "the requested product type" and "English" from the drop down lists, click the search button. Finally, click on the document title of your choice. 2-3 Safety device settings FXMQ-MVE PC BOARD FUSE 250V 10A Systems Indoor Units

6 3 Accessories FXMQ-MVE DRAIN PUMP KIT KDU30L125VE KDU30L250VE HIGH EFFICIENCY FILTER 65% KAFJ302L71 KAFJ302L140 KAFJ372L280 HIGH EFFICIENCY FILTER 90% KAFJ303L71 KAFJ303L140 KAFJ373L280 FILTER CHAMBER KDDJ30L71 KDDJ30L140 KDJ3705L280 REPLACEMENT LONG LIFE FILTER KAFJ301L71 KAFJ301L140 KAFJ371L280 3D040334A Main Unit High Efficiency Filter Drain Pump Kit Filter Chamber High Efficiency Filter 3 Systems Indoor Units 221

7 3 Accessories 3-1 Drain pump kit Specifications KDU30L125VE KDU30L250VE POWER SUPPLY single phase v/220v 50/60hz POWER CONSUMPTION W 19/17 (50/60hz) DRAIN-UP LIFT mm standard drain outlet of the unit +294 standard drain outlet of the unit +197~+447 DRAIN OUTLET VP25 (internal diameter ø25, external diameter ø32) SAFETY DEVICE float switch WEIGHT kg 9 10 APPLIED MODELS class class Precaution at use When this kit will be used together with the natural evaporation pan type humidifier, the piping of unit's drain and humidifier's drain can be used in common. Be sure to do test run (cooling) to make sure the drain flows out. Prohibit providing a drain trap when the drain pump kit will be mounted Installation Spot hose Drain hose Drain hose insulation Drain pipe insulation Hose band 1 Connect the drain connection hose from the elbow of the connection hose to the drain pump box. Connect the attached drain hose to the outlet of the drain pump. 2 Keep the drain hose sloping downwards. Hose band Hose band Drain connection Elbow 3 Ceiling slab more KDU30L125VE KDU30L250VE A 520 mm 590 mm Indoor unit Ceiling Drain pump kit 222 Systems Indoor Units

8 3 Accessories 3-1 Drain pump kit Internal wiring method KDU30L125VE Indoor unit Drain pump lead wire Clamps Drain pump wires Float switch Float switch wire X8A Indoor PC board assembly (Indoor unit) Remove the short circuit connector?(drain pump kit) Electric parts box Drain pump kit Electric parts box cover Float switch lead wire KDU30L250VE Fan partition plate Relay harness (1) Drain pump lead wire 3 Float switch lead wire Float switch Drain plug Indoor PC board assembly X8A?(Drain pump kit) (Indoor unit) Remove the short circuit connector Insulator (1) Drain pump lead wire Remove a cushion Float switch lead wire Systems Indoor Units 223

9 3 Accessories 3-2 High efficiency filter Specifications 65% type 90% type KAFJ302L71 KAFJ302L140 KAFJ372L280 KAFJ303L71 KAFJ303L140 KAFJ373L280 FILTER CHAMBER KDDJ30L71 KDDJ30L140 KDJ3705L280 KDDJ30L71 KDDJ30L140 KDJ3705L280 DIMENSION WxDxT mm 545x270x25 468x270x25 684x445x60 545x270x25 468x270x25 684x445x60 AVERAGE DUST COLLECTION EFFICIENCY % colorimetric method 65% colorimetric method 90% INITIAL PRESSURE LOSS Pa FINAL PRESSURE LOSS Pa FILTER non-woven fabric of synthetic fiber non-woven fabric of synthetic fiber LIFE TIME h 2,500 hours (dust density 0.15mg/m 3 ) 1,800 hours (dust density 0.15mg/m 3 ) SEATS STRUCTURED APPLICABLE MODELS 40 class 50,63,80 class 100 class 125 class 200,250 class 40 class 50,63,80 class 100 class 125 class 200,250 class NOTE 1 The filter chamber is separately required when the high efficiency filter will be installed Dimensions 545 (L71) 468 (L140) 684 (L280) Air flow Filter medium (L71 140) 445 (L280) 25 (L71 140) 60 (L280) 224 Systems Indoor Units

10 3 Accessories 3-2 High efficiency filter Filter characteristics Pressure loss KAFJ303L71 KAFJ302L71 KAFJ303L140 KAFJ302L140 KAFJ373L280 KAFJ372L280 (Pa) Air volume (m 3 /min) Installation Wing nut Main unit Cover for filter chamber Screw Filter chamber (KDDJ30L type) Air suction flange (supplied) 3 Air flow Screw High efficiency filter (option) Air suction duct (field supply) Meet the airflow direction and arrow mark putting on the high efficiency filter. It is impossible to be built in together with the air cleaning unit Systems Indoor Units 225

11 3 Accessories 3-3 Replacement long life filter Specifications Dimensions KAFJ301L71 KAFJ301L140 KAFJ371L280 FILTER CHAMBER FOR BOTTOM SUCTION KDDJ30L71 KDDJ30L140 KDJ3705L280 DIMENSIONS WxDxT mm 547x252x30 419x252x30 684x445x30 519x252x30 AVERAGE EFFICIENCY (%) % 50% (gravity method) PRESSURE LOSS (PA) Initial Pa 9.8 (1 mmh2o) Final Pa 49 (5 mmh2o) MATERIAL mildew proof resin net NUMBER REQUIRED PER UNIT 1 2 (each 1) 2 LIFE TIME (H) h 2,500 h (dust particle concentration at 0.15mg/m 3 ) APPLICABLE MODEL Class Class Class Filter medium Air flow Model A B Quantity KAFJ301L KAFJ301L (each 2 filters) KAFJ371L The filter chamber is required when the long life filter will be installed Filter characteristics 3 Pressure loss KDDJ30L71 KDDJ30L140 (Pa) KDJ3705L280 Air volume (m 3 /min) 226 Systems Indoor Units

12 4 Control systems 4-1 Individual control systems WIRED REMOTE CONTROL BRC1D527 INFRARED REMOTE CONTROL Heat pump BRC4C62 Cooling only BRC4C64 SIMPLIFIED REMOTE CONTROL BRC2A51 REMOTE CONTROL FOR HOTEL USE BRC3A Centralised control systems CENTRALISED REMOTE CONTROL UNIFIED ON/OFF CONTROL SCHEDULE TIMER DCS302C51 DCS301B51 DST301B Others WIRING ADAPTER WIRING ADAPTER FOR ELECTRICAL APPENDICES (1) WIRING ADAPTER FOR ELECTRICAL APPENDICES (2) REMOTE SENSOR ELECTRICAL BOX WITH EARTH TERMINAL (3 BLOCKS) ELECTRICAL BOX WITH EARTH TERMINAL (2 BLOCKS) NOISE FILTER (FOR ELECTROMAGNETIC INTERFACE USE ONLY) EXTERNAL CONTROL ADAPTER FOR OUTDOOR UNITS (INSTALLATION ON INDOOR UNIT) KRP1B61 KRP2A61 KRP4A51 KRCS01-1 KJB311A KJB212A KEK26-1 DTA104A61 3D034600B 4 Systems Indoor Units 227

13 5 Capacity tables 5-1 Cooling capacity 5 Unit size Nominal capacity Outdoor air temp. TC: Total capacity;kw SHC: Sensible capacity;kw Indoor air temperature 14.0WB 16.0WB 18.0WB 19.0WB 20.0WB 22.0WB 24.0WB 20.0DB 23.0DB 26.0DB 27.0DB 28.0DB 30.0DB 32.0DB CDB TC SHC TC SHC TC SHC TC SHC TC SHC TC SHC TC SHC Systems Indoor Units

14 5 Capacity tables 5-1 Cooling capacity Unit size Nominal capacity Outdoor air temp. TC: Total capacity;kw SHC: Sensible capacity;kw Indoor air temperature 14.0WB 16.0WB 18.0WB 19.0WB 20.0WB 22.0WB 24.0WB 20.0DB 23.0DB 26.0DB 27.0DB 28.0DB 30.0DB 32.0DB CDB TC SHC TC SHC TC SHC TC SHC TC SHC TC SHC TC SHC Systems Indoor Units 229

15 5 Capacity tables 5-2 Heating capacity Outdoor Indoor air temperature CDB Unit Size Nominal capacity air temperature CDB CWB kw kw kw kw kw kw Systems Indoor Units

16 5 Capacity tables 5-2 Heating capacity Outdoor Indoor air temperature CDB Unit Size Nominal capacity air temperature CDB CWB kw kw kw kw kw kw Systems Indoor Units 231

17 6 Dimensions 6-1 Dimensional drawings FXMQ40,50MVE 22 - ø 4.7 hole 750 or more 700 or more 26 - ø 4.7 hole Inspection hole 450 or more 10 - ø 8 hole View Nr Part name Description 1 Liquid pipe connection ø 6.4 flare connection 2 Gas pipe connection ø 12.7 flare connection 3 Drain pipe connection VP25 (O.D. ø32, I.D. ø25) 4 Ground terminal M4 5 Switch box 6 Interunit wiring connection 7 Power supply connection 8 Air discharge flange 9 Air suction flange 10 Hook For M8~M10 Discharge side Suction side (Note. 2) 14 - ø 8 hole 1 Location of unit's name plate: switch box surface. 2 Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more). 3 Be sure to install a drain trap, as the drain outlet of the air-conditioner becomes negative pressure. 4 Be sure to install a drain trap for each unit separately, when you install a consolidated drain piping. 3D FXMQ63,80MVE 22 - ø 4.7 hole or more 700 or more 10 - ø 8 hole 26 - ø 4.7 hole Inspection hole 450 or more View Nr Part name Description 1 Liquid pipe connection ø 9.5 flare connection 2 Gas pipe connection ø 15.9 flare connection 3 Drain pipe connection VP25 (O.D. ø32, I.D. ø25) 4 Ground terminal M4 5 Switch box 6 Interunit wiring connection 7 Power supply connection 8 Air discharge flange 9 Air suction flange 10 Hook For M8~M10 Discharge side Suction side (Note. 2) 14 - ø 8 hole 1 Location of unit's name plate: switch box surface. 2 Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more). 3 Be sure to install a drain trap, as the drain outlet of the air-conditioner becomes negative pressure. 4 Be sure to install a drain trap for each unit separately, when you install a consolidated drain piping. 3D Systems Indoor Units

18 6 Dimensions 6-1 Dimensional drawings FXMQ100,125MVE 40 - ø 4.7 hole 1,100 or more 38 - ø 4.7 hole View 18 - ø 8 hole Nr Part name Description 1 Liquid pipe connection ø 9.5 flare connection 2 Gas pipe connection ø 15.9 flare connection 3 Drain pipe connection VP25 (O.D. ø32, I.D. ø25) 4 Ground terminal M4 5 Switch box 6 Interunit wiring connection 7 Power supply connection 8 Air discharge flange 9 Air suction flange 10 Hook For M8~M10 Discharge side 700 or more Inspection hole 450 or more Suction side (Note. 2) 18 - ø 8 hole 1 Location of unit's name plate: switch box surface. 2 Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more). 3 Be sure to install a drain trap, as the drain outlet of the air-conditioner becomes negative pressure. 4 Be sure to install a drain trap for each unit separately, when you install a consolidated drain piping. 3D FXMQ200,250MVE Piping size (field supply) 32 - ø 4.7 hole Model Gas Liquid FXMQ200MVE ø 19.1 attached piping ø 9.5 FXMQ250MVE ø 22.2 attached piping ø ø 4.7 hole 650 or more Discharge side View 1,100 or more Approx Inspection hole 600 or more Suction side (Note. 2) View Nr Part name Description 1 Liquid pipe connection Flare connection 2 Gas pipe connection Attendant piping connection 3 Ground terminal M5 (Inside switch box) 4 Switch box 5 Power supply wiring connection 6 Transmission wiring connection 7 Hook M10 8 Discharge companion flange 9 Suction flange 10 Attached piping Brazing 11 Name plate 12 Drain piping connection PS1B Internal thread VP25 (O.D. ø33.349, I.D. ø30.391) 13 Water supply port ø 8 hole 1 Location of unit s name plate: switch box surface. 2 Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more). 3D Systems Indoor Units 233

19 6 Dimensions 6-2 Dimensional drawings with drain pump kit FXMQ40-80MVE 740 (Suspending positions) 670 (Suspending positions) 750 or more Access panel 450 square or more Nr Part name Description 1 Ceiling mounted duct type s body 2 Drain pump kit 3 Drain pipe connection VP25 (O.D. ø32) 4 Water extracting hole 5 Drain connection pipe Attached to the drain pump kit 1 Be sure to provide an air filter in the suction air duct (with dust collection efficiency by more than 50% in the weight method.) 2 When the drain pump kit will be mounted, don't provide a trap in the drain pipe line. DU K FXMQ100,125MVE 1,060 (Suspending positions) 6 about (Suspending positions) 1,110 or more Nr Part name Description 1 Ceiling mounted duct type s body 2 Drain pump kit 3 Drain pipe connection VP25 (O.D. ø32) 4 Water extracting hole 5 Drain connection pipe Attached to the drain pump kit 1 Be sure to provide an air filter in the suction air duct (with dust collection efficiency by more than 50% in the weight method.) 2 When the drain pump kit will be mounted, don't provide a trap in the drain pipe line. DU D 234 Systems Indoor Units

20 6 Dimensions 6-2 Dimensional drawings with drain pump kit FXMQ200,250MVE 32 ø4.7 hole (Circumference) 32-ø7 hole (Circumference) A view 650 or more about or more Access panel 600 square (For indoor unit's filter) 16-ø8 hole Nr Part name Description 1 Ceiling mounted duct type s body 2 Filter chamber 3 High efficiency filter 4 Long life filter 5 Drain pump kit Built in a body 6 Drain piping connection VP25 (O.D. ø32, I.D.ø25) 7 Water inlet 8 Drain hose Attached to drain pump kit 3D011124B 6 Systems Indoor Units 235

21 6 Dimensions 6-3 Dimensional drawings with high efficiency filter/long life filter FXMQ40-80MVE 750 or more 430 or more Access panel 450 mm square or more Nr Part name Description 1 Ceiling mounted duct type s body 2 Filter chamber 3 High efficiency filter 4 Long life filter 1 Be sure to provide an air filter in the suction air duct (with dust collection efficiency by more than 50% in the weight method.) 2 Be sure to install a drain trap in the drain piping because the outlet of drain will fall to negative pressure. 3 When a centralised drain system will be applied, each indoor unit should have a drain trap individually. DU G FXMQ100,125MVE or more 750 or more Nr Part name Description 1 Ceiling mounted duct type s body 2 Filter chamber 3 High efficiency filter 4 Long life filter Access panel 450 mm square or more 1 Be sure to provide an air filter in the suction air duct (with dust collection efficiency by more than 50% in the weight method.) 2 Be sure to install a drain trap in the drain piping because the outlet of drain will fall to negative pressure. 3 When a centralised drain system will be applied, each indoor unit should have a drain trap individually. DU G 236 Systems Indoor Units

22 6 Dimensions 6-4 Centre of gravity FXMQ40-125MVE Model A B FXMQ40,50,63,80MVE FXMQ100,125MVE 1, D FXMQ200,250MVE Air outlet Air inlet 6 4D Systems Indoor Units 237

23 6 Dimensions 6-5 Bolt pitch FXMQ40-125MVE FXMQ200,250MVE Suspension bolt (x4) Suspension bolt (x4) 1,148 1,100 Air outlet Indoor unit Air inlet Indoor unit 1,296 1,380 Air outlet Air inlet Inspection hatch 450 Model A B FXMQ40MVE FXMQ50MVE FXMQ63MVE FXMQ80MVE FXMQ100MVE FXMQ125MVE 670 1, ,100 1,100 or more (service space) Approx. 150 mm Inspection hatch Install a canvas duct to the air discharge outlet and air inlet so that vibration from the machine body is not transmitted to the duct or ceiling. You should also apply acoustic (insulation material) to the inside of the duct, and vibration insulation rubber to the suspension bolts. 2 Install suspension bolts. Use bolts of 10 mm diameter. Install the equipment where supporting structures are strong enough to bear the equipment s weight. Use embedded inserts or anchor bolts with new buildings and hole-in-anchors with old buildings. 6 Ceiling slab Anchor Long nut or turn-buckle Suspension bolt Indoor unit NOTE 1 All the above parts are to be procured in the field. 3P Systems Indoor Units

24 7 Piping Diagram FXMQ-MVE Heat exchanger Gas pipe connection port Th3 Th1 Fan Th2 Liquid pipe connection port Filter Filter Electronic expansion valve Piping connection diameters Model Gas Liquid FXMQ40,50MVE ø12.7 ø6.4 FXMQ63,80,100,125MVE ø15.9 ø9.5 FXMQ200MVE ø19.1 ø9.5 FXMQ250MVE ø22.2 ø9.5 7 Th1 : Thermistor for suction air temperature Th2 : Thermistor for liquid line temperature Th3 : Thermistor for gas line temperature Check valve Flare connection Screw connection Flange connection Pinched pipe Spinned pipe 4D Systems Indoor Units 239

25 8 Wiring Diagrams FXMQ40-125MVE Power supply Electric parts box Note 4 Input from outside Note 3 Transmission wiring centralised remote control Note 2 Wired remote control (Optional accessory) Indoor unit Optional parts A1P Printed circuit board M1F Motor (indoor fan) M1P Motor (drain pump) A2P Terminal board Q1M Thermo switch M1F built-in only C1R Capacitor (M1F) R1T Thermistor (air) Wired remote control R2T R3T Thermistor (coil) SS1 Selector switch (main/sub) F1U Fuse (250V, 5A, ) type S1L Float switch R1T Thermistor (air) F1U Fuse (250V, 10A, ) type T1R Transformer ( V/22V) HAP Light emitting diode (service monitor-green) X1M Terminal strip (power) K1R-K3R Magnetic relay (M1F) X2M Terminal strip (control) Connector for optional parts KPR Magnetic relay (M1P) Y1E Electronic expansion valve X18A Connector (wiring adapter for electrical appendices) 8, : Terminal : Connector : Field wiring COLORS : BLK : Black PNK : Pink BLU : Blue RED : Red BRN : Brown WHT : White ORG : Orange YLW : Yellow 1 Use copper conductors only. 2 In case of high E.S.P. operation, change the wiring connection of X2A as shown. 3 In case of using centralised remote control, connect it to the unit in accordance with the attached instruction manual. 4 When connecting the input wires from outside, forced off or on/off control operation can be selected by remote control, more details can be found in the installation manual attached to the unit. 3D039620A 240 Systems Indoor Units

26 8 Wiring Diagrams FXMQ200,250MVE Power supply Electric parts box Note 5 Note 4 Input from outside Note 3 Transmission wiring Centralised remote control Wired remote control (Optional accessory) Indoor unit Optional parts A1P Printed circuit board Q1M Q2M Thermo switch (M1F 2F embedded) M1P Motor (drain pump) C1R 2R Capacitor (M1F 2F) R1T Thermistor (air) F1U Fuse (250V, 5A, ) R2T 3T Thermistor (coil) Wired remote control HAP Light emitting diode (service monitor-green) SS Selector switch (static pressure) SS1 Selector switch (main/sub) K1M Magnetic contactor (M1F 2F) T1R Transformer ( V/22V) R1T Thermistor (air) K2M Magnetic contactor (M1F 2F) X1M Terminal strip (power) K3M Magnetic contactor (M1F 2F) X2M-X3M Terminal strip Connector for optional parts K1R-K2R Magnetic relay (M1F 2F) X4M Terminal strip (control) KPR Magnetic relay (M1P) Y1E Electronic expansion valve X8A Connector (float switch) M1F 2F Motor (indoor fan) X18A Connector (wiring adapter for electrical appendices), : Terminal : Connector : Jumper connector : Field wiring COLORS : BLK : Black PNK : Pink BLU : Blue RED : Red BRN : Brown WHT : White ORG : Orange YLW : Yellow 8 1 In case of high E.S.P. operation, change the switch (SS) for H. 2 Use copper conductors only. 3 In case of using centralised remote control, connect it to the unit in accordance with the attached instruction manual. 4 When connecting the input wires from outside, forced off or on/off control operation can be selected by remote control. 5 In case of installing the drain pump, remove the jumper and execute the additional wiring for float switch (S1L). 3D039621A Systems Indoor Units 241

27 9 Sound level 9-1 Sound level data Model Sound pressure level - 220V H L Measuring location Sound power level FXMQ40MVE * FXMQ50MVE Discharge Suction * FXMQ63MVE Duct Duct * FXMQ80MVE * FXMQ100MVE * FXMQ125MVE * FXMQ200MVE * FXMQ250MVE * 1 Reference acoustic pressure 0 db = 20 Pa. 2 Measuring place: anechoic chamber 3 Operation noise differs with operation and ambient conditions. *Data were not available at the time of publication 9-2 Sound pressure spectrums 220V 240V FXMQ40,50MVE 4D034593A FXMQ63MVE 4D034594A FXMQ80,100MVE 4D034595A Octave band sound pressure level db (OdB = bar) Approximate threshold hearing for continuous noise Octave band sound pressure level db (OdB = bar) Approximate threshold hearing for continuous noise Octave band sound pressure level db (OdB = bar) Approximate threshold hearing for continuous noise 9 Octave band center frequency (Hz) Octave band center frequency (Hz) Octave band center frequency (Hz) FXMQ125MVE 4D FXMQ200MVE 4D FXMQ250MVE 4D Octave band sound pressure level db (OdB = bar) Approximate threshold hearing for continuous noise Octave band sound pressure level db (OdB = bar) Approximate threshold hearing for continuous noise Octave band sound pressure level db (OdB = bar) Approximate threshold hearing for continuous noise Octave band center frequency (Hz) Octave band center frequency (Hz) Octave band center frequency (Hz) 242 Systems Indoor Units

28 10 Fan characteristics FXMQ40,50,63MVE 3D019610A FXMQ80MVE 3D018375A FXMQ100MVE 3D000067C 50 HZ 220V (mmh 2 0) External static pressure Upper limit of external static pressure (high ESP) (Pa) (mmh 2 0) Upper limit of external static pressure (standard ESP) Low (standard ESP) Low (high ESP) High (standard ESP) Upper limit of external static pressure (standard ESP) High (high ESP) Upper limit of external static pressure (high ESP) 50 HZ 220V (mmh 2 0) (Pa) (mmh 2 0) External static pressure Low (standard ESP) Upper limit of external static pressure (high ESP) Low (high ESP) Upper limit of external static pressure (standard ESP) High (standard ESP) High (high ESP) Lower limit of external static pressure (high ESP) Lower limit of external static pressure (standard ESP) 50 HZ 220V External static pressure Upper limit of external static pressure (high ESP) Low (high ESP) Upper limit of external static pressure (standard ESP) High (standard ESP) High (high ESP) Lower limit of external static pressure (standard ESP) Lower limit of external static pressure (high ESP) Low (standard ESP) (mmh 2 0) (Pa) Air flow (m 3 /min) (mmh 2 0) (mmh 2 0) (Pa) Air flow (m 3 /min) (mmh 2 0) Air flow (m 3 /min) FXMQ125MVE 3D000167C FXMQ200MVE 3D FXMQ250MVE 3D HZ 220V 50 HZ 220V (mmh 2 0) (Pa) (mmh 2 0) 50 HZ 220V (mmh 2 0) (Pa) (mmh 2 0) External static pressure Upper limit of external static pressure (standard ESP) Low (high ESP) Upper limit of external static pressure (standard ESP) High (high ESP) High (standerd ESP) Lower limit of external static pressure (standard ESP) Lower limit of external static pressure (high ESP) External static pressure Upper limit of ESP (high ESP) Low (high ESP) Upper limit of ESP (standard ESP) Low (standard ESP) Lower limit of ESP (standard ESP) High (high ESP) Lower limit of ESP (high ESP) High (standard ESP) External static pressure Upper limit of ESP (high ESP) Low (high ESP) Upper limit of ESP (standard ESP) Low (standard ESP) Lower limit of ESP (standard ESP) High (high ESP) Lower limit of ESP (high ESP) High (standard ESP) (mmh 2 0) (Pa) Air flow (m 3 /min) (mmh 2 0) 10 Low (standard ESP) (mmh 2 0) (Pa) Air flow (m 3 /min) (mmh 2 0) Air flow (m 3 /min) 1 The remote control can be used to switch between high and low. 2 The air flow is set to standard before leaving the factory. It is possible to switch between standard ESP and high ESP by changing the terminals in the indoor unit electrical box. Systems Indoor Units 243

29 11 Installation 11-1 Installation example Air outlet Suction grille Remote control 11-2 Service space 1. Select an installation site: Where the following conditions are fulfilled and that meets with your customer's approval. Where sufficient clearance for maintenance and service can be ensured. Where optimum air distribution can be ensured. FXMQ40-125MVE FXMQ200,250MVE 470 Min. 450 Min. 700 (service space) Model FXMQ40MVE FXMQ50MVE FXMQ63MVE FXMQ80MVE FXMQ100MVE FXMQ125MVE A 750 1,100 Min. 650 (service space) NOTE 1 Above figures mean minimum values. 3P Where nothing blocks the air passage. Where condensation can be properly drained. Where piping between indoor and outdoor units is possible within the allowable limit (Refer to the installation manual of the outdoor unit.) If supporting structural members are not strong enough to take the unit's weight, the unit could fall out of place and cause serious injury. Keep the indoor and outdoor units, power cable and transmission wiring, at least 1 m from TVs and radios, to prevent distorted pictures and static. (Depending on the type and source of the electrical waves, static may be heard even when more than 1 m away.) 2. Check whether the place is strong enough to bear the weight of the unit or not. If there is a risk, reinforce the place before installing the unit. 244 Systems Indoor Units

30 11 Installation 11-3 Drain piping Rig the drain pipe as shown below and take measures against condensation. Improperly rigged piping could lead to leaks and eventually wet furniture and belongings. Insulate the drain hose inside the buildings 1. Install the drain pipes FXMQ40-125MVE Keep piping as short as possible and slope it downwards so that air does not remain trapped inside the pipe. Attached drain hose Keep pipe size equal to or bigger than that of the connecting pipe (Vinyl pipe of 25 mm I.D. and 32 mm E.D.). Bottom of unit Use the attached drain hose and clamp. Tighten the clamp firmly. 5 cm or more Insulate the clamp metal with the attached sealing pad. There is negative pressure inside the unit relative to atmospheric pressure when the unit is running, so be sure to provide drain trap on the drain outlet. (See the figure) In order to prevent foreign matters from building up inside the piping, you should avoid curves as much as possible, and arrange so the trap can be cleaned. Clamp metal (Attached with unit) Large sealing pad (Attached with unit) Clamp metal 5 cm or more NOTE 1 If installing centralised drain piping, install according to the following right figure. (Install a drain trap for each indoor unit.) 4 mm or less Drain hose Drain hose 100 mm or more FXMQ MVE A drain pipe need not be installed. The diameter of the piping is the same as that of the connecting pipe (PS1B), and should be kept equal to or bigger than that of the connecting pipe. 2. After piping work is finished, check if drainage flows smoothly. 11 Systems Indoor Units 245

31 Systems ISO14001 assures an effective environmental management system in order to help protect human health and the environment from the potential impact of our activities, products and services and to assist in maintaining and improving the quality of the environment. Daikin Europe N.V. is approved by LRQA for its Quality Management System in accordance with the ISO9001 standard. ISO9001 pertains to quality assurance regarding design, development, manufacturing as well as to services related to the product. Daikin units comply with the European regulations that guarantee the safety of the product. VRV products are not within the scope of the Eurovent certification programme. Daikin equipment is designed for comfort applications. For use in other applications, please contact your local Daikin representative. Specifications are subject to change without prior notice Zandvoordestraat 300 B-8400 Ostend - Belgium EEDE04-2/2A 10/2004 Prepared in Belgium by Lannoo