lindab rainline technical information roof drainage system Lindab Rainline TM Lindab Roof Drainage System Technical Information

Transcription

1 lindab rainline technical information roof drainage system indab Rainline TM indab Roof rainage System Technical Information

2 ensioning Roof drainage ensioning can be done according to Swedish Standard SS or the Advice and instructions for the code of practice, Hus AMA, RA 08 Hus. ensioning to SS gives smaller dimensions than if RA 08 Hus is used. This is because RA 08 Hus has given some consideration to the tendency of gutters to fill up with sludge from leaves and loose material on roof cladding etc. SS compensates this by specifying a smallest fall for self-clearance of 5-7 mm/m, depending on dimensions. iagrams and tables based on the dimensioning instructions in SS and Hus AMA are included below. ensioning to SS SS diagrams contain curves for various rain intensities. It approves the assumption that the probable rain intensity can be specified as l/ (sm 2 ) on areas less than 10,000 m 2 for the whole country, which is what our diagram is based on. SS assumes that the gutter is laid with a smallest fall of 2.5 mm/m. Since SS does not cover our entire product range, the curves in SS have been extrapolated. It should be noted that the dimen sioning instructions in SS can give a relationship between gutters and down pipes which does not correspond with the product standard for nozzles. This is because of traditional and appearance demands for size matching between gutters and down pipes. A v = True roof area 1 and 2 = istance from building corner Example Roof area = 20 m, B = 9 m A v = 180 m 2 A down pipe located 11.6 m from one end = = Result You can choose a half round gutter of R125 or larger. The down pipe from the second diagram should then be SRÖR75. Roofarea A v m 2 R 190 R R 125 R 1 RER = A v = SRÖR 120 SRÖR 111 SRÖR SRÖR SRÖR A v

3 Rainline Colour chart Number Name Nearest NCS Nearest RA 001 Antique white S 2-GY Black S 9000-N Antracite metallic S 6000-N Silver metallic ark grey S 7005-B20G Brown S 8005-Y80R Tile red S 4040-Y80R ark red S 40-Y80R Copper metallic S 4030-Y60R Pine green S 7010-G30Y 6020 Other material Aluminium-zinc 3

4 Gutter with accessories R Gutter d Area* Area** mm mm mm 2 mm d *Sectional area **Water carrying area (6 mm lower front edge,190 gutter 11mm) RSK Gutter joint SSK Adjustable snap bracket Ø5,5 To SS-EN 1462 Class A-H STAG Stay strap Ø4 4

5 Gutter with accessories K33/K24/K21/K16/K07 Bracket mm K33 K24 K21 K16 K /6 25/30 Ø5, To SS-EN 1462 Class A-H K11 Bracket for 27 roof pitch To SS-EN 1462 Class A-H Ø5,5 KF35/KF/KFM Bracket mm KF35 KF KFM Ø5, To SS-EN 1462 Class A-H KFK Fascia Bracket To SS-EN 1462 Class A-H 5 25 Ø5,5 5

6 Gutter with accessories KBO Bracket bender TB Cover brace A A-A Ø4 5 A 29 OMV Gutter outlet A H /d mm mm / / / / / 174 1/ / / / / /

7 Gutter with accessories RG Stop end RGV/RGH Stop end RVI Gutter angle, inner mm RVY Gutter angle, outer mm

8 Gutter with accessories RVI135 Gutter angle 135, inner mm RVY135 Gutter angle 135, outer mm ÖSK Overflow protection A A A-A 170 ÖSKR Overflow protection, straight 125 A A A-A 8

9 own Pipe with accessories SRÖR own pipe Area i/d mm A A 5900 i d A-A To SS-EN 612 Class A X BUTKF Reinforced drain shoe 2,2 Ø125 Material: Extruded aluminium Ø90 UTKF Reinforced shoe Material: Extruded aluminium. 2,2 Ø SVHÅF Reinforced pipe holder The holder is reversible for different wall spacings

10 own Pipe with accessories MST Intermediate pipe Cuts into suitable pieces i 111 BK70 Bends 70 i/d i R * Not BM. Will be replaced by 70 degrees bends, radius 110 mm. d BM70 Bends 70 /d R * Not BM. Will be replaced by 70 degrees bends, radius 110 mm. SOKN One piece bend d /d d d 10

11 own Pipe with accessories SRORM Pipe connector /d SRORM fits both inside and outside the downpipe. d SSVH Pipe holder With wedge locking in aluminium-zinc design SSV Pipe holder for spike With wedge locking in aluminium-zinc design and fixed spine. SST Spike mm

12 80 lindab rainline roof drainage system own Pipe with accessories GRÖR Adjustable branch d VATK Hopper h Ø h d FRK Gutter hook ,5 195,5 Ø5,5 25 SAS Connector for 80 mm hose

13 own Pipe with accessories UTK Shoe mm R BUTK rain shoe 1 2 mm mm VSI eaf filter Stainless steel Ø95 PRT Sliding pipe The sliding pipe fits outside the down pipe. 13

14 own Pipe with accessories RT rain trap (H polythene) eaf filter in H polythene for down pipes. The lower section fits standard ground pipes/junction pipes Ø SS Self cleaning leaf trap Self cleaning leaf filter in H polythene for down pipes. The lower section fits standard ground pipes Ø MRT rain connector Connector for H polythene filters. For connection to ground pipes with dimensions other than standard. 105 Ø101 Ø96 Ø79 FUTK Adjustable shoe 75 2 d 14

15 Rectangular Gutter with accessories RER Gutter Area* mm * Water carrying area RERSK Gutter joint 136 RERGH/RERGV Stop end A 136 A-A A 45 REK07/REK21 Bracket 5 25 REK07 mm REK21 Ø5,

16 Rectangular Gutter with accessories REOK Nozzle H /d mm / / / H d RERVI Gutter angle, inner mm RERVY Gutter angle, outer mm

17 Accessories STIFT Touch up paint with applicator brush 17

18 Notes

19 Notes

20 lindab rainline technical information roof drainage system indab Building Components is a business area within the indab Group that develops, manufactures and markets efficient, economical and aesthetic steel and sheet metal solutions for the building industry. We offer a wide range of components and systems for all types of housing, as well as commercial and industrial buildings. indab Building Components is represented in over 30 countries throughout Europe. Our head office is in Förslöv, in the south of Sweden. Art no indab Profile SE Båstad Phone +46 (0)