ToppTube PA11 (Polyamide) page 4. ToppTube PA12 (Polyamide) page 5. ToppTube PA12HIPHL (Polyamide) page 6. ToppTube PUR 98A (Polyurethane) page 7

Transcription

1

2

3 ToppTube PA11 (Polyamide) page 4 ToppTube PA12 (Polyamide) page 5 ToppTube PA12HIPHL (Polyamide) page 6 ToppTube PUR 98A (Polyurethane) page 7 ToppTube PE-LD (Polyethylene) page 8 ToppTube PE-LLD (Polyethylene) page 9 ToppTube PE-HD (Polyethylene) page 10 ToppTube PEX (Polyethylene) page 11 ToppSpiral Spiral Tubes page 12 ToppPart Pre-Bent Tubes page 13 ToppMulti Multi-Cables page 14

4 Flexible pressure-resistant tubes for pneumatic and hydraulic applications, as well as for grease lubrication. Superior in high temperature applications. Good impact resistance Excellent abrasion resistance PA11 hard quality PA11P40 semi-hard quality PA11F15 soft quality Technical information Material Hardness Polyamide PA11 (Nylon 11) Rilsan PA11: 70 Shore D, PA11P40: 63 Shore D, PA11F15: 52 Shore D Installation Temperature -20 C C Working Temperature -40 C C Operating Pressure 4,0 bar bar (depending on tube dimensions and temperature). Tolerances According to DIN Colours Natural, black, blue, yellow, red, green, silver, etc. Outer diameter 3,0 mm...28,0 mm x inner diameter 2,0 mm...24,0 mm. Chemical Resistance PA tubes have good chemical resistance against oils, hydraulic fluids, and fuels. Not suitable for chloride compounds. Value Unit Test Method Density 1,05 g/cm³ ISO 1183 mm Working pressure (bar), safety factor 3 PA11 PA11P40 PA11F15 Temperature C Temperature C Temperature C Weight Bending radius O.D./I.D. 23 C 40 C 60 C 80 C 23 C 40 C 60 C 80 C 23 C 40 C 60 C g/m min. mm 4/ ,9 24 5/ ,2 30 6/ ,5 36 8/ , / , / , / , /12, , / , / , / ,9 196 Besides standard dimensions we can also manufacture special dimensions. 4 The company reserves the right to make changes without notice.

5 Good impact resistance Superior in high temperature applications High pressure resistance Applications Pneumatics Industrial robots Instrumentation lines Technical information Material Polyamide PA12 (Nylon 12) Hardness PA12: Special product, PA12P40: 60 shore D Installation Temperature -20 C C Working Temperature -40 C C Operating Pressure 4,0 bar bar (depending on tube dimensions and temperature). Tolerances According to DIN Colours Natural, black, blue, yellow, red, green, silver, etc. Chemical Resistance mm Outer diameter 3,0 mm...28,0 mm x inner diameter 2,0 mm...24,0 mm. PA tubes have good chemical resistance against oils, hydraulic fluids, and fuels. Not suitable for chloride compounds. Value Unit Test Method Density 1,03 g/cm³ ISO 1183 PA12 Working pressure (bar), safety factor 3 PA12P40 Temperature C Temperature C Weight Bending radius O.D./I.D. 23 C 40 C 60 C 80 C 23 C 40 C 60 C 80 C g/m min. mm 4/ ,9 24 5/ ,2 30 6/ ,5 36 8/ , / , / , / , /12, , / , / , / ,9 196 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 5

6 We manufacture the brake tubes strictly according to the DIN quality standard which requires a black colour. Vehicle tubes are manufactured according to the DIN quality standard, which offers many colour alternatives. Applications: Flexible brake tube for automotive applications For demanding installations Automotive Technical information Material PA12HIPHL-DIN Hardness 63 Shore D ISO 868 Installation Temperature -20 C C Working Temperature -40 C C Operating Pressure 4,0 bar bar (depending on tube dimensions and temperature). Tolerances According to DIN Colours Black in DIN Red, blue, yellow in DIN Outer diameter 4,0 mm...18 mm x inner diameter 2,0 mm...14,0 mm Chemical Resistance Excellent chemical resistance against oils, hydraulic fluids and fuels. Not suitable for chloride compounds. Value Unit Test Method Density 1,03 g/cm³ ISO 1183 Working pressure (bar), safety factor 3 mm Temperature C Weight Bending radius O.D./I.D. 23 C 40 C 60 C 80 C g/m min. mm 4/ ,9 24 6/ ,5 36 6,4/4, ,5 38 8/ ,1 50 9/ ,1 54 9,5/6, , / , / , / , / , ,7/9, , / , ,8/11, , / , / Besides standard dimensions we can also manufacture special dimensions. 6 The company reserves the right to make changes without notice.

7 Good flexible properties, performes especially well in low temperatures Wide operating temperature range Excellent abrasion resistance No plasticizers used Excellent elasticity - small bending radius Applications: Pneumatics Industrial robots Instrumentation lines Technical information Material Hardness Polyurethane C98A 98 Shore A Installation Temperature -30 C C Working Temperature -40 C C, momentarily 100 C Operating Pressure 2,0 bar...19 bar (depending on tube dimensions and temperature). Tolerances According to DIN Colours Silver, black, blue (yellow, red, green, natural) etc. Outer diameter 3,0 mm...16 mm x inner diameter 2,0 mm...13,0 mm Chemical Resistance Excellent chemical resistance against oils, hydraulic fluids and fuels. Value Unit Test Method Density 1,22 g/cm³ ISO A Working pressure (bar), safety factor 3 mm Temperature C Weight Bending radius O.D./I.D. 20 C 30 C 40 C 50 C 60 C 70 C g/m min. mm 4/ ,1 9 4,3/2, ,0 15 5, ,5 14 5/3, ,5 15 6/3, ,0 20 6/ ,9 21 8/5, ,0 34 8/ ,7 40 9,5/6, , / , / , / , / , /12, ,6 118 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 7

8 Low density polyethylene Economical price Reasonable heat and pressure resistance Suitable for recycling using modern methods of shredding and cleaning Good chemical resistance Applications PE-LD tubing is often used in pneumatic equipment due to its easy installation. Technical information Material PE-LD Installation Temperature -30 C C Working Temperature -40 C C Operating Pressure 1,0 Bar...22 Bar (depending on tube dimensions and temperature). Tolerances According to DIN Colours Natural, black, blue, (yellow, red, green, silver, etc.) Outer diameter 4,0 mm...22 mm x inner diameter 2,0 mm...18,0 mm Chemical Resistance Good chemical resistance against gases and liquids. Value Unit Test Method Density 0,922 g/cm³ ISO 1183 Working pressure (bar), safety factor 2,5 mm Temperature C Weight Bending radius O.D./I.D. 20 C 30 C 40 C 50 C 60 C g/m min. mm 4/ ,9 24 5/ ,2 30 6/ ,5 36 8/ , / , / , / , /12, , / , / , / ,9 196 Besides standard dimensions we can also manufacture special dimensions. 8 The company reserves the right to make changes without notice.

9 Linear low density polyethylene Good chemical resistance Economical price Applications: Pneumatic installations Installations where gas and chemical contact is required. Technical information Material PE-LLD Installation Temperature -30 C C Working Temperature -40 C C Operating Pressure Depending on tube dimensions and temperature. Tolerances According to DIN Colours Blue, natural, black. Other colours by request. Outer diameter 4,0 mm...22 mm x inner diameter 2,0 mm...18,0 mm Chemical Resistance Good chemical resistance against gases and liquids. Value Unit Test Method Density 0,931 g/cm³ ISO 1183 Working pressure (bar), safety factor x mm Temperature C Weight Bending radius O.D./I.D. 20 C 40 C 60 C g/m min. mm 4/ ,8 24 5/ ,7 30 6/ ,6 36 8/ , / , / , / , /12, , / , / , / ,0 196 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 9

10 Low cost tube with superior chemical resistance High impact strenght for more demanding applications Technical information Material PE-HD High-density polyethylene Hardness 65 Shore D ISO 868 Installation Temperature -30 C C Working Temperature -30 C C Operating Pressure Depending on tube dimensions and temperature. Tolerances According to DIN Colours Colours by request. On request. Chemical Resistance Good chemical resistance against gases and liquids. Value Unit Test Method Density 0,958 g/cm³ ISO The company reserves the right to make changes without notice.

11 A high density cross linked polyethylene Good processabilty High density Flexible Excellent chemical resistance Excellent heath resistance Excellent impact resistance Applications: Piping Plumbing parts Portable water applications Technical information Material Cross-linked polyethylene PEX Installation Temperature -30 C C Working Temperature -40 C C Operating Pressure 1,0 bar 33 bar (depending on tube dimensions and temperature) Tolerances According to DIN Colours Black, blue, natural Outer diameter 4,0 mm...22 mm x inner diameter 2,0 mm...18,0 mm Chemical Resistance Excellent chemical resistance in lower pressures and temperatures, especially against gases and liquids. Value Unit Test Method Density 0,942 g/cm³ ASTM D792 The company reserves the right to make changes without notice. 11

12 Handy accessibility with a tailored spiral tube! ToppSpiral PA is a premium quality spiral tube. Its flexibility provides handy accessibility in pneumatic systems. The tube is made of durable polyamid which maintains its shape. For vertical installations we recommend a semi-rigid quality, and for horizontal installations a rigid quality. We manufacture ToppSpiral PA spiral tubes to order. In the table you can find several samples. If you can t find the spiral you need, please call us and let us know the dimensions and the outer and inner diameter of the requested spiral. I.D. B A O.D. Recommendation Ordering Colours Sizes Tube dimensions mm. For horizontal fitting medium hard polyamide, for vertical fitting hard polyamide. The spirals are manufactured by request. Standard colour is blue, other colours by request. Other sizes or with straight heads by request. Spiral dimensions mm. O.D. I.D. Work length B Ø Free length A 4,0 2, ,0 4, ,0 6, ,0 6, ,0 8, ,0 8, ,0 10, ,0 12, ,0 12, ,0 12, ,0 19, ,0 2, ,0 4, ,0 4, ,0 6, ,0 8, ,0 8, ,0 10, ,0 12, ,0 12, ,0 12, ,0 19, ,0 2, ,0 4, ,0 4, ,0 6, ,0 8, ,0 8, ,0 10, ,0 12, ,0 12, ,0 12, ,0 19, ,0 4, ,0 4, ,0 6, ,0 8, ,0 8, ,0 10, ,0 12, ,0 12, ,0 12, ,0 19, Besides standard dimensions we can also manufacture special dimensions. 12 The company reserves the right to make changes without notice.

13 Faster and easier installations with ToppPart tubes! The pre-bent ToppPart tubes are designed for instant installations in pneumatic and liquid applications. Hence, the installation of ToppPart tubes is very fast and easy. And less time in installations means savings. ToppPart tubes are an alternative in applications in which it is not possible to use metal tubing. ToppPart tubes are tailored according to customer s specific needs. We can manufacture both 2D and 3D shapes using our unique state of the art CNC bending technology. What material we can bend? We currently have the capability to bend PA11, PA12 and PEX tubes with an outer diameter between 6 mm and 30 mm, into an almost limitless variations of bends to fit any application. Want to know more? For more information please contact our customer service: customerservice@toppi.fi. A, B and C refers to the length between bends, these can be between 120 mm mm. We will be happy to consider the dimensions on request. The company reserves the right to make changes without notice. 13

14 One product - multiple solutions A ToppMulti cable is a selection of e.g. pneumatic tubes, fluid tubes, electrical cables and optical fibres combined into one cable. We manufacture the ToppMulti cables according to our customers specific needs. Notes Not a stock item. Minimum order quantity 500 meters. General Information and Quality Certificate Extruded PE- (Polyethylene) PA- (Polyamide) or PUR- (Polyurethane) tubes in variable combinations covered General with a PVC jacket. Other materials in tubing and jacket on request. Continuous measurement of tube outer diameter from two directions, wall thickness at six points. Quality control Regular control of the tubes burst pressure. Tolerance of tubes Complying DIN Number of tubes 1-19 pcs., the maximum number of tubes depends on the individual tube sizes. Electrical cables Optional for supplying of electrical signals, usually supplied by customer. PVC-jacket PVC (polyvinyl chloride), black, blue or grey. Other materials on request. Bending radius Minimum seven (7) times the maximum measure of the jacket. Lenghts Standard length is 500 m, delivered on drum. Protective foil Polyester, standard thickness 12 µm. O-3 PE - 6/4 BLACK L-3 PE - 6/4 BLACK Example LAL-3 PE - 6/4 BLACK OAL-3 PE - 6/4 BLACK O More or less round jacket, maximum 3 pcs. filler profiles used. L Jacket only. LAL Jacket with aluminium (12 µm) and polyester foil (12 µm), and without filler profiles. OAL Jacket with aluminium (12 µm) and polyester foil (12 µm), and filler profiles. Explanation 3 Number of tubes, numbering clockwise begining from center. PE Polyethylene tubing used. 6/4 Tube size, the tubes can have different colors (max. 6) or numbering. BLACK The color of jacket, other colours on request. 14 The company reserves the right to make changes without notice.

15 TUBES JACKET Cross section Article pcs. Raw Material Color Raw Material L-1PE-6/4 BLACK 1 PE (alternative PA or PUR) BLACK PVC (other materials on request) L-2PE-6/4 BLACK 2 PE (alternative PA or PUR) BLACK PVC (other materials on request) L-3PE-6/4 BLACK 3 PE (alternative PA or PUR) BLACK PVC (other materials on request) O-2PE-6/4 BLACK 2 PE (alternative PA or PUR) BLACK PVC (other materials on request) O-3PE-6/4 BLACK 3 PE (alternative PA or PUR) BLACK PVC (other materials on request) O-7PE-6/4 BLACK 7 PE (alternative PA or PUR) BLACK PVC (other materials on request) JACKET MEASURES Article ~ Weight kg/m ~ Outer mm L-1PE-6/4 0,060 Ø 9,4 L-1PE-8/6 0,075 Ø 11,4 L-1PE-10/8 0,091 Ø 13,4 L-2PE-6/4 0,089 15,4 x 9,4 L-2PE-8/4 0,115 19,4 x 11,4 L-2PE-10/8 0,140 23,4 x 13,4 L-3PA-6/4 0,104 15,4 x 14,6 L-3PE-6/4 0,104 15,4 x 14,6 O-2PE-6,4/4,3 0,119 Ø 16,2 O-2PE-6/4 0,113 Ø 15,4 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 15

16 Oy Toppi Ab Tiilismäki Espoo Finland Telephone asiakaspalvelu@toppi.fi customerservice@toppi.fi