Retrofitting instructions

Transcription

1 EN-XX Retrofitting instructions Randscheibe links Randscheibe rechts NA_Deckblatt_ _EN

2 Table of contents SAFETY NOTES Professional Qualification... 3 Intended Use... 3 Prior to Starting Assembly Work... 3 General Safety Notes for Assembly... 4 Prior to Starting Up... 4 RETROFITTING INSTRUCTIONS Blown-up drawing... 5 Parts list... 6 Fit boundary disc... 7 Final inspection Before setting to work

3 SAFETY NOTES Professional Qualification These assembly instructions are aimed exclusively at skilled staff trained for this work. Intended Use Intended use is described in the machine s Operating Instructions. The attachment or installation of additional equipment does not constitute a change to the machine s intended use. Prior to Starting Assembly Work Park the machine on firm level ground, switch off the tractor s engine, apply the hand brake, remove the ignition key and keep safe. Allow the machine to come to a complete stop (rotating parts may carry on turning for a longish period). Secure machine and tractor against accidental rolling. Secure work area so that there can be no risk to or for other people. Observe the statutory regulations on accident prevention. Observe warning signs (pictograms) on the machine

4 SAFETY NOTES General Safety Notes for Assembly DANGER Risk of severe or life-threatening injuries all over the body due to getting caught up, being pulled in, crushing and hydraulic oil escaping at high pressure! It is imperative to follow the safety notes! Only couple and uncouple the machine on solid level ground, secure against accidental rolling and falling over. Only carry out work if the PTO drive shaft and the motor have been switched off, the handbrake has been applied and the ignition key has been removed and kept safe. Wait until all rotating machine parts come to a complete stop! Wear close-fitting workwear and use personal protective equipment such as safety glasses, gloves, safety shoes and safety helmet! Only raise the machine using lifting gear suitable for the purpose (hydraulic jack, crane, etc.) and only support it using appropriate supporting elements. No welding, cutting, grinding, drilling on frame, axles or other load-bearing parts. Check nuts and bolts for tight fit. Hoses and cables may not strain, rub or become trapped. Attachment or installation of non-standard equipment alters the overall weight and depending on the non-standard equipment involved may also alter the external dimensions of the machine. Pay attention to the altered dimensions in operation and particularly when driving on public roads. Attach sufficient ballast weights to the tractor. At least 20% of the vehicle s unladen weight on the front axle. Insufficient ballast will make tractor and machine uncontrollable when driving. Do not step between tractor and machine whilst attaching/coupling up. Have someone guide you in if the coupling point cannot be seen from the driver s seat of the tractor. Do not step between tractor and machine until both have come to a stop and have been secured against accidental rolling. Bring the supporting devices (e.g. support legs) into the correct position in each case. Secure as prescribed! Do not get close to hydraulic oil escaping under high pressure. Prior to Starting Up Follow the machine s Operating Instructions. Check safety equipment for completeness and function. Check oil levels. Check machine for compressed air and oil losses. Check tyre pressures and wheelnuts for tight fit. Check electrical, pneumatic and hydraulic connections to the tractor. Check service brake and parking brake for proper function. Completely release machine s parking brake and turn the crank handle inwards. Place tractor s hydraulic control unit in neutral position prior to attaching the machine. Pay attention to lateral locking of the tractor s three-point linkage depending on the machine type

5 RETROFITTING INSTRUCTIONS Blown-up drawing _NA_ _EN - 5 -

6 Parts list PNR TEILE-NR MENGE BENENNUNG DESIGNATION DESCRIPTION BEMERK/REMARQUE FU ============================================================================================================================================= RANDSCHEIBE LINKS DISQUE GAUCHE DISC LEFT HOHLSCHEIBE LI. ZUS. DISQUE DISC ( SEITENFLANSCH LI.SZ. TUBE SUPPORT GAUCHE SUPPORTING TUBE LEFT SEITENFLANSCH FLASQUE FLANGE BOLZEN SZ AXE PIN LASCHE ECLISSE PLATE SK-SCHRAUBE M20X160 DIN VIS SCREW SK-SCHR. M12X60 DIN VIS M12X60 SCREW M12X SI-MUTTER M12 DIN ZN ECROU M12 DIN NUT M12 DIN SI-MUTTER M20 DIN ECROU M20 NUT M KLAPPVORSTECKER 12X45 DIN11023 GOUPILLE 12X45 PIN 12X HOHLSCHEIBE 450/100X5 DISQUE DISC SCHEIBENTRAEGER LI. SZ SUPPORT DE DISQUE DISC ARM NABE MOYEU HUB STAUBKAPPE CACHE ROUGE CAP WELLENDICHTRING 40X55X7 BAGNE D ETANCHEITE OIL SEAL KEGELROLLENLAGER ROULEM.A ROUL.CONI. TAPER ROLLER BEARING SICHERUNGSRING 62 SEGMENT D ARRET CIRCLIP KEGELROLLENLAGER DIN 720 ROULEM.A ROUL.CONI. TAPER ROLLER BEARING SPLINT 3,2X36 DIN 94 ST ZN GOUPILLE FENDUE COTTERPIN SCHMIERNIPPEL A M6 DIN RACCORD DE GRAISSEUR GREASING NIPPLE SK-SCHRAUBE M10X30 - DIN 933 VIS SCREW SI-MUTTER M10 DIN ECROU M10 DIN 980 NUT M10 DIN KRONENMUTTER FL.M24X1,5 DIN937 ECROU CRÉNEAUX CASTLE NUT SPANNSTIFT 8X32 DIN 1481 GOUPILLE MECANINDUS ROLLPIN SCHEIBENHALTER STANDARD SUPPORT SUPPORT BOLZEN SZ AXE PIN KLAPPVORSTECKER 6X42 DIN 11O23 GOUPILLE FENDUE PIN LINCH SICHERHEITSSCHNUR GTO F SECURITE-CORDE SECURITY-CORD SK-SCHR. M16X60 DIN ZN VIS M16X60 SCREW M16X SK-SCHRAUBE M10X60 DIN VIS SCREW SI-MUTTER M16 DIN ZN ECROU M16 DIN 980 NUT M16 DIN SI-MUTTER M10 DIN ECROU M10 DIN 980 NUT M10 DIN SPANNSTIFT 16X18 DIN 148 GOUPILLE MECANINDUS ROLLPIN 0965/BT _NA_ _EN - 6 -

7 Fit boundary disc All diagrams show the fitting of component (left boundary disc)! Component (right boundary disc) is fitted similarly on the other side of the machine! 1200_NA_ _EN - 7 -

8 _NA_ _EN - 8 -

9 Centre of hollow disc aligns with end of last share! Hollow disc End of last share This is the factory setting. Adapt setting accordingly where necessary. 4x 1200_NA_ _EN - 9 -

10 Carry out procedure similarly on both sides of machine. 1200_NA_ _EN

11 Final inspection - Check all screwed connections and plug-in connections for perfect condition and tight seat. - Upon completion of the assembly, grease all lubrication points for the first time as described in the maintenance instructions (see operating instructions) and check the oil level of all gearboxes, etc. Fill up, if necessary. For suitable lubricants consult the maintenance instructions, which are part of the operating instructions. Before setting to work - Check safety devices for completeness and correct function. - Read the operating instructions carefully and make sure that all safety instructions are observed _MA_Kontrolle_EN

12 PÖTTINGER Service Support Centres Austria PÖTTINGER Landtechnik GmbH Industriegelände Grieskirchen Phone Fax info@poettinger.at Deutschland PÖTTINGER Deutschland GmbH Landsberg Service Centre Spöttinger Straße Landsberg am Lech Phone Fax info@poettinger.at PÖTTINGER Deutschland GmbH Recke Sales and Service Centre Steinbecker Straße Recke Phone Fax France PÖTTINGER France S.a.r.l. La Chapelle 129b Le Bonhomme Phone Fax france@poettinger.at Italia POETTINGER Italia s.r.l. Via E. Fermi San Pietro in Cerro/PC Phone Fax

13 Polska PÖTTINGER Polska Poladowo Smigiel United Kingdom Alois POTTINGER UK Ltd. St. Marks Road 15 NN18AN Corby Phone Fax Ireland POETTINGER Ireland Ltd. Cashel road, Clonmel Co. Tipperary Phone Україна PÖTTINGER Ukraine Prywokzalna vulitsa 50, Office Boryspil Phone Россия OOO "POETTINGER" Bachruschin Str. 32/ Moskau Phone Fax Canada POETTINGER Canada Inc. 650 Route 112 J0L 1T0 St. Cesaire Phone Fax

14 United States POETTINGER US, Inc. 393 Pilot drive Valparaiso/IN Phone Fax POETTINGER US, Inc. West Iona Ave Lemoore/CA Australia POETTINGER Australia PTY LTD 15 Fordson Street Campbellfield/VIC 3061 Phone

15 PÖTTINGER Service Partner A worldwide network of well established Service Specialist Centres is at your disposal. This regional proximity guarantees the prompt supply of spare parts, enables optimum product handover and parameterisation of machines through competent personnel. Our service features include: Expertise through the regular training of professional personnel. 24 hour online ordering service for ORIGINAL INSIDE replacement parts. Long-term availability of replacement parts. And much more Contact your nearest Specialist Service Centre for more information, or go to