Original operating manual

Size: px
Start display at page:

Download "Original operating manual"

Transcription

1 matev GmbH Nürnberger Str Langenzenn T F info@matev.eu Original operating manual Engine PTO Shaft FPS-PTO JD-3R for John Deere, type 3033R, 3038R, 3045R 2000 rpm CCW 2000 rpm CW 1000 rpm CCW 1000 rpm CW Version 06/2015

2 Table of contents Table of contents 1. About this operating manual Safety Intended use Qualifications of personnel General safety notices Special safety notices Supplemental provisions Installation Preparatory measures Mounting the engine PTO shaft Connect the electrical system Installation is complete Operation Coupling and uncoupling implements Mounting the universal joint shaft Dismounting the universal joint shaft Switching the engine PTO shaft on and off Maintenance Service Changing the gear oil Repair Disposal Guarantee List of illustrations Declaration of Conformity... 24

3 About this operating manual 1. About this operating manual Dear customer! Thank you for purchasing this implement, we appreciate your trust. Prior to using this implement for the first time, read this operating manual carefully and conscientiously all the way through. Keep this operating manual where it is easily accessible. This will enable you to refer to important information and handling instructions as needed. Listings with bullet points are marked as follows: Text Text Text Handling instructions are marked in the sequence in which they should be executed, as follows: Text Text Text... This implement is subject to change in the interest of technical progress. All information, illustrations, and technical specifications represent the latest status at the time this manual was published. The manufacturer reserves the right to make changes at any time in the interest of technical progress. Page 3

4 Safety 2. Safety Guidelines and instructions with which you must comply, are summarized in this section. Personnel who install, operate and maintain these implements, must have read and understood this operating manual Intended use The engine PTO shaft extends the crankshaft of the tractor to the front. It is used to power sweepers, front mowers, or similar implements that are driven with PTO shafts. This engine PTO shaft should only be mounted on tractors, as specified on the cover sheet. Non-intended use causes: Health hazards for the operator or for third parties Damage to the tractor and the implements Environmental damage 2.2. Qualifications of personnel Only personnel 18 years of age or older, or instructed personnel should install, operate, and maintain the implements. The operator must have read and understood this operating manual General safety notices General safety instructions are explained in this section. These safety instructions are used in the subsequent chapters. In addition to the safety aspect, you will save money and work time if you follow these safety instructions. Danger! Severe injury to the operator or third parties occurs. Comply with the safety notice. Minor injury of the operator or third parties can occur. The tractor, the grass collection device or the environment can be damaged. Comply with the safety notice. Note! Important, helpful tips or information for the operator. Read this note. It facilitates your work. Injuries can occur. Wear protective work clothing. Page 4

5 Safety 2.4. Special safety notices The safety instructions specified in this chapter are also affixed as stickers on the implements. Danger of injury due to moving parts. Remove the ignition key before performing maintenance tasks on the implement. Injuries can occur due to improper operation. The implement can be damaged. Read the operating manual all the way through. Comply with the safety instructions. Injuries due to fluid escaping under high pressure. Comply with the notice in the operating manual. Increased risk of accident due to rotating PTO shaft. Do not enter the work area of the PTO shaft when it is rotating. For your own safety do not wear any loose clothing, belts, or any other loose items. Switch off the implement. Wait until all machine parts have come to a standstill before converting or servicing the implement. Check all threaded unions prior to using the implement and after using the implement. Loosened connections must be re-tightened. Damage can occur Supplemental provisions Ensure that the speed and the direction of rotation of the engine PTO shaft are suitable for driving the implement before coupling an implement to the tractor. Always switch off the front PTO shaft and wait until the PTO shaft is no longer turning when you leave the tractor or work on the connected implement. Do not attempt to find a possible leak in the hydraulic system with your fingers. Oil under high pressure can easily penetrate skin and clothing and cause serious injury. Page 5

6 Installation 3. Installation Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key before mounting or dismounting the engine PTO shaft. Injuries can occur. Wear protective work clothing Preparatory measures The prerequisite for using the engine PTO shaft is that the tractor must already be equipped with the matev front power systems or Do not attach the front power system yet. If the tractor is already equipped with a front power system, it must be dismounted In conjunction with the JD frontloader H160 / H165 you need the matev frontloader conversion kit. Fig. 1: matev frontloader conversion kit Drive the tractor onto the lift platform. Completely remove the battery with the battery tray. Page 6

7 Installation Fig. 2: Battery with tray Dismount all attachment parts from the battery tray. You will need the attachment parts later Make the cut out for the engine PTO shaft in the plastic cover as shown in the diagram below. Slide piece, universal joint shaft Fig. 3: Cutout for engine PTO shaft Place the slide piece for the universal joint shaft (flange with 6 bores) radiator and axle. If the pulley is mounted, the slide piece can no longer be pushed through Mount the provided pulley on the pulley on the engine. Use the provided Allen screws DIN 912 M10x Secure the screws with a liquid thread-lock compound. Tighten the screws with a torque of 43 Nm. If the tractor is equipped with an air conditioning system, then the pulley for the AC compressor must be replaced with the provided pulley. Page 7

8 Installation Mount the slide piece of the universal joint shaft on the pulley. Use the provided hex screws DIN933-M6x Secure the screws with a liquid thread-lock compound. Tighten the screws with a torque of 9 Nm. Fig. 4: Pulley with universal joint shaft Slide the splined shaft part of the universal joint shaft onto the slide piece. Fig. 5: Universal joint shaft installed Page 8

9 Installation 3.2. Mounting the engine PTO shaft Note! The gearbox is already filled with oil. Keep this in mind when handling the gearbox. The engine PTO shaft is prepared for operation without an additional radiator. The provided grub screw M6x6 must be mounted so that the radiator will function. After the grub screw is mounted the engine PTO shaft must only be operated with radiator, otherwise the engine PTO shaft will be damaged! Place the gearbox diagonally on the ground. The gearbox is supported on the driven shaft. On the gearbox, dismount the plug for flow and return Mount the provided grub screw in the return for the cooling Mount the provided extenders in the flow. Use the copper seal Ø10.2 for the extension. Flow cooling Mount the provided grub screw M6x6 in the channel! Return cooling Fig. 6: Installation quick-release connections Mount the quick-release connections on the gearbox Fasten the gearbox on the base body of the front power system with two screws DIN 933-M10x30-8.8, and two screws DIN 933-M10x Place the washers Ø10.5x30x4 under the screw head. Secure the screws with a liquid thread-lock compound. Tighten the screws with a torque of 43 Nm. Page 9

10 Installation Extension for quickrelease connection "flow" Fig. 7: Gearbox - pre-assembled Mount the front power system as described in the manual, "Front Power System and Engine PTO Shaft FPS-JD-3R Fasten the universal joint shaft on the flange of the engine PTO shaft. Use the provided Allen screws DIN 912-M8x Secure the screws with a liquid thread-lock compound. Tighten the screws with a torque of 22 Nm. Fig. 8: Fasten the universal joint shaft on the gearbox flange Screw the reducers and the quick-release connections into the radiator. Use the provided seals between reducer and radiator. Mount the radiator with the holder. Page 10

11 Installation Holder Fig. 9: Mounting the cooler Mount the rubber grommets for the hose passage on the provided cover plate. Cover plate Rubber grommet Fig. 10 Cover plate Mount the cover plate instead of the battery tray on the tractor. Pull the plastic hoses through the rubber grommets Shorten the hoses and the protective tubes. Slide the protective tubes over the plastic hose and insert the plastic hoses in the quick-release connections on the radiator Mount the attachment parts that you dismounted from the battery tray, on the cover plate. Mount the extension between ground cable and frame. Page 11

12 Installation Radiator hose with protective tube Extension for ground cable Fig. 11: Cover plate with cooling hoses mounted Mount the battery. Only connect the battery after complete installation of the engine PTO shaft Cut out the radiator grill as shown in the diagram below Connect the electrical system Page 12

13 Installation Fig. 12: PTO shaft switch + cable Connect PTO shaft switch and cable. Mount the switch on the empty space on the tractor. Fig. 13: PTO shaft switch (tractor without cab) Page 13

14 Installation Fig. 14: PTO shaft switch (tractor with cab) Detach the instrument panel on the tractor and lift it off. Find the cable for the engine PTO shaft. Remove the protective plug with the bridge and connect it to the PTO switch. Plug connector for PTO switch Fig. 15: Cable for engine PTO shaft (tractor without cab) Page 14

15 Installation Plug connector for PTO switch Fig. 16: Cable for engine PTO shaft (tractor with cab) Refasten the instrument panel The cable for the connection on the engine PTO shaft is at the front, on the right, near the front axle. Remove the protective cap from the plug and connect the plug connection to the engine PTO shaft. Plug connector for engine PTO shaft Front axle Fig. 17: Plug connection engine PTO shaft Page 15

16 Installation Mount the PTO shaft guard on the gearbox. Fig. 18 PTO shaft guard 3.4. Installation is complete Check all threaded unions. To conclude, ensure that all cables and hoses are sufficiently far away from moving parts and that there is no injury hazard. Remove all tools and loose parts from the tractor Check the oil level. The tractor must be on a level surface. Open the oil fill plug. The oil level must be below the oil fill plug. Top up oil as needed Check whether the gearbox vent unit is mounted. Mount the gearbox vent unit here Oil fill plug Oil drain plug Fig. 19: Gearbox vent unit Page 16

17 Operation Vent screw Fig. 20: Mounted vent screw Increased risk of accident due to rotating PTO shaft. Do not enter the work area of the PTO shaft when it is rotating. For your own safety do not wear any loose clothing, belts, or any other loose items. Switch off the implement. Wait until all machine parts have come to a standstill before converting or servicing the implement. Injuries due to fluid escaping under high pressure. Comply with the notice in the operating manual Reconnect the battery Perform a trial run. Switch on the tractor. Ensure that the engine PTO shaft is at a standstill. Switch on the engine PTO shaft in idle and listen for unusual noises. Increase the speed to full throttle. Switch off the engine PTO shaft. Ensure that the engine PTO shaft is at a standstill After the trial run check all bolts, cables, and hoses for firm seat as the concluding step. 4. Operation Before starting up the implement, read the instructions on safety and handling for operation of the entire implement and connection to the tractor. Page 17

18 Operation The total power of the front implements must not be exceeded, depending on the gearbox, otherwise the front PTO shaft could be damaged. CW CCW Max. power 42 kw 84 kw 42 kw 84 kw Rotational speed on the gearbox output Max. permissible drive torque for implements 1000 rpm 2000 rpm 1000 rpm 2000 rpm 400 Nm 4.1. Coupling and uncoupling implements Note! Comply with the axle loads specified by the tractor manufacturer Increased risk of accident due to rotating PTO shaft. Do not enter the work area of the PTO shaft when it is rotating. For your own safety do not wear any loose clothing, belts, or any other loose items. Switch off the implement. Wait until all machine parts have come to a standstill before converting or servicing the implement Drive the tractor forward in front of the implement Lower the front power system Drive slowly toward the implement until the coupling triangle of the tractor is under the coupling triangle of the implement Slowly lift the front power system until the implement is slightly lifted Secure the implement with the appropriate triangle locking mechanism. The triangle locking mechanism depends on the type of implement. Damage can occur to the engine PTO shaft or to the tractor Comply with the instructions in the operating manual provided by the manufacturer of the universal joint shaft. Note! Mount the universal joint shaft as described in the original manual provided by the manufacturer of the universal joint shaft. Page 18

19 Operation 4.2. Mounting the universal joint shaft Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key before mounting or dismounting the engine PTO shaft. Increased risk of accident due to rotating PTO shaft. Do not enter the work area of the PTO shaft when it is rotating. For your own safety do not wear any loose clothing, belts, or any other loose items. Switch off the implement. Wait until all machine parts have come to a standstill before converting or servicing the implement Press the locking pin on the outer fork and keep it depressed Slide the outer fork onto the profile stub of the front PTO shaft on the gearbox Release the locking pin Slightly move the universal joint shaft back and forth until the locking pin audibly locks in place Repeat steps 1 to 4 to attach the universal joint shaft to the implement Hook the safety chain of the universal joint shaft to a fixed part (see Fig. 21). Fig. 21 Safety chain on the universal joint shaft 4.3. Dismounting the universal joint shaft Danger! Severe injury to the operator or third parties occurs. Switch off the tractor and remove the ignition key before mounting or dismounting the engine PTO shaft. Increased risk of accident due to rotating PTO shaft. Do not enter the work area of the PTO shaft when it is rotating. For your own safety do not wear any loose clothing, belts, or any other loose items. Switch off the implement. Wait until all machine parts have come to a standstill before converting or servicing the implement Detach the safety chain on both sides Press the locking pin on the outer fork and keep it depressed Pull the outer fork down from the profile stub of the PTO shaft on the tractor Release the locking pin Repeat steps 2 to 4 to detach the universal joint shaft on the implement. Page 19

20 Maintenance 4.4. Switching the engine PTO shaft on and off Switching on the engine PTO shaft: switch on the engine PTO shaft at approx rpm, and do not increase the rpm of the tractor engine when switching on the engine PTO shaft. Do not switch on the engine PTO shaft at a rotational speed greater than 1200 rpm Switching off the engine PTO shaft: switch off the switch for the front PTO shaft Never attempt to loosen a seized front implement by switching the engine PTO shaft on and off. 5. Maintenance 5.1. Service After 5-10 operating hours with a new engine PTO shaft, or after a repair, check whether all bolts are still tightened to the correct torque. Check all hydraulic lines for leaks. After every 400 operating hours check all threaded connections for correct tightening torque. Check the hydraulic lines for leaks. Lubricate the universal joint shaft. After 100 operating hours check the oil level. Place the tractor on a horizontal surface and check whether the oil reaches the fill plug. If necessary top-up with oil. After 450 operating hours, or every 6 months change the gear oil. Clean the oil filter in the pump unit. The universal joint shaft must be lubricated every 250 operating hours, however at the latest after 1 month Changing the gear oil Remove the oil drain plug and drain the oil into a collection container. The oil drain plug is on the front side of the gearbox Unscrew the screw on the cover for the oil filter and remove the cover. Page 20

21 Maintenance Cover for oil filter Fig. 22 Gearbox rear view Oil fill plug Oil drain plug Fig. 23 Gearbox front view Remove the oil filter from the pump unit, clean it, for example with compressed air Replace the oil filter and remount the cover Screw the oil drain plug back in Remove the oil fill plug and fill with 1 l oil (Hygard JDMJ 20C). Remount the oil fill plug. Page 21

22 Repair 6. Repair Never open the gearbox on your own. If there are faults, problems, or other indications of malfunction, contact your sales consultant or contact the manufacturer directly: matev GmbH Nürnberger Str Langenzenn Tel.: +49 (0) Disposal The implement must be disposed of in accordance with the applicable regulations of the municipality or the country. Take the parts to the collection points for residual waste, special waste, or recycle them depending on material. matev GmbH does not provide any disposal services. 8. Guarantee The general terms and conditions of matev GmbH apply. Page 22

23 List of illustrations 9. List of illustrations Fig. 1: matev frontloader conversion kit... 6 Fig. 2: Battery with tray... 7 Fig. 3: Cutout for engine PTO shaft... 7 Fig. 4: Pulley with universal joint shaft... 8 Fig. 5: Universal joint shaft installed... 8 Fig. 6: Installation quick-release connections... 9 Fig. 7: Gearbox - pre-assembled Fig. 8: Fasten the universal joint shaft on the gearbox flange Fig. 9: Mounting the cooler Fig. 10 Cover plate Fig. 11: Cover plate with cooling hoses mounted Fig. 12: PTO shaft switch + cable Fig. 13: PTO shaft switch (tractor without cab) Fig. 14: PTO shaft switch (tractor with cab) Fig. 15: Cable for engine PTO shaft (tractor without cab) Fig. 16: Cable for engine PTO shaft (tractor with cab) Fig. 17: Plug connection engine PTO shaft Fig. 18 PTO shaft guard Fig. 19: Gearbox vent unit Fig. 20: Mounted vent screw Fig. 21 Safety chain on the universal joint shaft Fig. 22 Gearbox rear view Fig. 23 Gearbox front view Page 23

24 10. Declaration of Conformity EC Declaration of Conformity for a machine to confirm compliance with the Machinery Directive 2006/42/EC, the EMC Directive 2004/108/EC, and with the statutory regulations issued for their implementation. The manufacturer matev GmbH Nürnberger Str Langenzenn declares that the machine Engine PTO shaft FPS-PTO JD-3R / / / type John Deere 3033R/3038R/3045R complies with the provisions of the Machinery Directive 2006/42/EC, The EMC Directive 2004/108/EC and with the national statutory regulations for their implementation. The signer is authorized to compile the technical documents. The address is the address of the manufacturer. Date / signature March Name of signer Signer information Georg Hemmerlein Managing Director _FPS-PTO JD 3R_BA_deu_AZS_EN Copyright matev All rights reserved. Subject to change!

Original Operating Manual

Original Operating Manual matev GmbH Nürnberger Str. 50 90579 Langenzenn T +49 (0) 9101 9087-0 F +49 (0) 9101 9087-20 info@matev.eu www.matev.eu Original Operating Manual Front Power System und Front PTO shaft FPS- JD X 950 R for

More information

Original Operating Manual

Original Operating Manual matev GmbH Nürnberger Str. 50 90579 Langenzenn T +49 (0) 9101 9087-0 F +49 (0) 9101 9087-20 info@matev.eu www.matev.eu Original Operating Manual Snow blade SRM-FB 120 CD Angle adjustment mechanical Version

More information

Original Operating Manual

Original Operating Manual matev GmbH Nuernberger Str. 50 90579 Langenzenn T +49 (0) 9101 9087-0 F +49 (0) 9101 9087-20 info@matev.eu www.matev.eu Original Operating Manual Sand and Salt Spreader SPR - IX 125 SPR - IX 250 SPR -

More information

Spare Parts List. Front sweeper SWE-SD 140 E SWE-SD 140/160 S. Implement type: Order number: / 5011

Spare Parts List. Front sweeper SWE-SD 140 E SWE-SD 140/160 S. Implement type: Order number: / 5011 matev GmbH Nürnberger Str. 50 90579 Langenzenn T +49 (0) 9101 9087-0 F +49 (0) 9101 9087-20 info@matev.eu www.matev.eu Spare Parts List Implement type: Front sweeper SWE-SD 140 E SWE-SD 140/160 S Order

More information

Spare Parts List Return line filter RF

Spare Parts List Return line filter RF Spare Parts List Return line filter up to 15000 l/min, up to 25 bar 30 60 110 160 240 330 450 580 660 950 1300 2500 4000 5200 6500-7800 15000 1. MAINTENANCE 1.1 GENERAL Please follow the maintenance instructions!

More information

RINK Model 1622 Series number:

RINK Model 1622 Series number: OPERATION MANUAL AND LIST OF PARTS RINK Model 1622 Series number: WARNING: IN ORDER TO ENSURE SAFE USE OF THE MACHINE AND OPTIMAL RESULTS, IT IS ESSENTIAL TO READ THIS OPERATION MANUAL CAREFULLY BEFORE

More information

Assembly and Maintenance Manual Type ASNU

Assembly and Maintenance Manual Type ASNU Assembly and Maintenance Manual Type ASNU Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_ASNU.docx

More information

LOG SPLITTER. Heavy Duty PTO Driven. Owners Illustrated Instruction Book & Parts List

LOG SPLITTER. Heavy Duty PTO Driven. Owners Illustrated Instruction Book & Parts List LOG SPLITTER Heavy Duty PTO Driven Owners Illustrated Instruction Book & Parts List Grovebury Road, Leighton Buzzard, Bedfordshire. LU7 4UX. UK. Tel:01525 375157. Fax:01525 385222. Email: enquires@brownsagricultural.co.uk

More information

AC 100. Operating instructions Pneumatic Crimper AC 100. Date of issue: 05/2010. Keep for future use!

AC 100. Operating instructions Pneumatic Crimper AC 100. Date of issue: 05/2010. Keep for future use! Operating instructions Pneumatic Crimper AC 100 Date of issue: 05/2010 Keep for future use! SAFETY SAFETY Basic information The basic prerequisite for ensuring safe use and continuous operation of the

More information

Operating instructions

Operating instructions Operating instructions Digital tank contents indicator DTA 10 DTA 10 DTA 10 0 4.0 m fuel oil 0 3.5 m water Read instructions before using device! Observe all safety information! Keep instructions for future

More information

Adjustable Speaker Mount GRAVIS 12

Adjustable Speaker Mount GRAVIS 12 Adjustable Speaker Mount GRAVIS 12 User's Manual Translation of the original instructions Version 3.3 Released: 19.01.2017 Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße

More information

Adjustable Speaker Mount GRAVIS 8

Adjustable Speaker Mount GRAVIS 8 Adjustable Speaker Mount GRAVIS 8 User's Manual Translation of the original instructions Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße 14 D-30179 Hannover TEL +49 (0)

More information

Operating Instructions Flexdip CYA112

Operating Instructions Flexdip CYA112 BA00432C/07/EN/13.13 71207066 Products Solutions Services Operating Instructions Wastewater assembly About this document Safety messages The structure, signal words and safety colors of the signs comply

More information

VARIFUEL MAINTENANCE AND REPAIR INSTRUCTIONS

VARIFUEL MAINTENANCE AND REPAIR INSTRUCTIONS VARIFUEL2 140-65 MAINTENANCE AND REPAIR INSTRUCTIONS MOTORTECH Gas Regulation P/N 01.50.008-140-65-EN Rev. 06/2015 Copyright Copyright 2015 MOTORTECH GmbH. All rights reserved. Distribution and reproduction

More information

SCOPELITE TIMING LIGHT OPERATING MANUAL

SCOPELITE TIMING LIGHT OPERATING MANUAL SCOPELITE TIMING LIGHT OPERATING MANUAL MOTORTECH Tools & Test Equipment for Ignition Systems P/N 01.10.020-EN Rev. 11/2015 Copyright Copyright 2015 MOTORTECH GmbH. All rights reserved. Distribution and

More information

USE AND MAINTENANCE MANUAL

USE AND MAINTENANCE MANUAL LATERAL TURNOVER 360 ORIGINAL INSTRUCTIONS INTRODUCTION This manual includes instructions for assembly, maintenance (regular and extraordinary), and for possible faults with remedies. The instructions

More information

Assembly and Maintenance Manual Type AS

Assembly and Maintenance Manual Type AS Assembly and Maintenance Manual Type AS Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_AS.docx

More information

VARIFUEL MAINTENANCE AND REPAIR INSTRUCTIONS

VARIFUEL MAINTENANCE AND REPAIR INSTRUCTIONS VARIFUEL2 200-120 MAINTENANCE AND REPAIR INSTRUCTIONS MOTORTECH Gas Regulation P/N 01.50.008-200-120-EN Rev. 06/2015 Copyright Copyright 2015 MOTORTECH GmbH. All rights reserved. Distribution and reproduction

More information

Quarter turn actuator DAPS..R..-F..

Quarter turn actuator DAPS..R..-F.. Quarter turn actuator DAPS..R..-F.. Festo AG & Co. KG Postfach D-73726 Esslingen +49 711 347-0 www.festo.com (en) Operating instructions 8030408 1309g [8030416] Original: de Quarter turn actuator DAPS..R..-F.....

More information

Compensation unit AGE-XY 50-80

Compensation unit AGE-XY 50-80 Translation of the origninal manual Compensation unit AGE-XY 50-80 Assembly and operating manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of

More information

Spare parts list Return line filter RFM with 2-hole attachment

Spare parts list Return line filter RFM with 2-hole attachment Spare parts list Return line filter with 2-hole attachment Tank-top mounted version: up to 200 l/min, up to 10 bar 75 90 150 165 185 195 1. MAINTENANCE 1.1 GENERAL Please follow the maintenance instructions!

More information

Assembly and maintenance manual Type FSO, FSO-GR, FS, HPI

Assembly and maintenance manual Type FSO, FSO-GR, FS, HPI Type FSO, FSO-GR, FS, HPI Hatschekstr.36 69126 Heidelberg Deutschland Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 23.08.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\M1124E_0_FSO_FSO-GR_FS_HPI.docx

More information

Spare Parts List Return Line Filter RFM with 4-hole attachment

Spare Parts List Return Line Filter RFM with 4-hole attachment Spare Parts List Return Line Filter with 4-hole attachment Tank-top mounted version: up to 850 l/min, up to 10 bar 75 90 150 165 185 195 210 270 330 500 600 661 851 1. MAINTENANCE GENERAL Please follow

More information

John Deere. MODEL: 2140 Volume 1 of 3 JD-S-TM4373

John Deere. MODEL: 2140 Volume 1 of 3 JD-S-TM4373 John Deere MODEL: 2140 Volume 1 of 3 THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY

More information

Rotary feed-through DDF-S/-KS

Rotary feed-through DDF-S/-KS Translation of the Original Operating Manual Rotary feed-through DDF-S/-KS Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

EN Operating manual. Motorised zone valve. Three-way, 22 mm & 28 mm 3PV2, 3PV8 & VRMH3

EN Operating manual. Motorised zone valve. Three-way, 22 mm & 28 mm 3PV2, 3PV8 & VRMH3 EN Operating manual Motorised zone valve Three-way, 22 mm & 28 mm 3PV2, 3PV8 & VRMH3 This manual ensures safe and efficient use of the 3PV2 or 3PV8 force-actuated three-way valve with spring-loaded return

More information

RESOL SBS 1000 * * Connection Operation

RESOL SBS 1000 * * Connection Operation RESOL SBS 1000 Connection Operation FlowCon SBS 1000 A www.resol.de *48003820* 48003820 Thank you for buying this RESOL product. Please read this manual carefully to get the best performance from this

More information

Spare Parts List Tank-Top Return Line Filter RFN with Elements to DIN up to 630 l/min, up to 10 bar

Spare Parts List Tank-Top Return Line Filter RFN with Elements to DIN up to 630 l/min, up to 10 bar Spare Parts List Tank-Top Return Line Filter RFN with Elements to DIN 24550 up to 630 l/min, up to 10 bar RFN 40 RFN 63 RFN 100 RFN 160 RFN 250 RFN 400 RFN 630 1. MAINTENANCE 1.1 GENERAL Please follow

More information

Parker Hannifin Filtration Group Racor Division DUAL FBO OPERATION AND MAINTENANCE INSTRUCTIONS SPARE PARTS

Parker Hannifin Filtration Group Racor Division DUAL FBO OPERATION AND MAINTENANCE INSTRUCTIONS SPARE PARTS Parker Hannifin Filtration Group OPERATION AND MAINTENANCE INSTRUCTIONS SPARE PARTS DFBO-10-IN/DFBO-14-IN DFBO-14-MA 2(23) Duplex Fuel Filter / Separator Operation and Maintenance Instructions 73309 031912

More information

Air Filter Element, Replacing and Cleaning Housing

Air Filter Element, Replacing and Cleaning Housing Air Filter Element, Replacing and Cleaning Housing Note Only use silicone-free lubricant for assembling the intake hoses. Secure all hose connections with hose clamps that match current standard production.

More information

Assembly and Maintenance Manual Type RSBW

Assembly and Maintenance Manual Type RSBW Assembly and Maintenance Manual Type RSBW Hatschekstr. 36 69126 Heidelberg Germany Tel +49(0)6221 30470 Tel +49(0)6221 304731 info@stieber.de www.stieber.de Stieber Clutch Date of issue: 16/03/2017 GB

More information

PrioVino Premier. Translation of Original Operating Instructions. Status: August First edition January 2018 / PrioVino GmbH

PrioVino Premier. Translation of Original Operating Instructions. Status: August First edition January 2018 / PrioVino GmbH PrioVino Premier Translation of Original Operating Instructions Status: August 2018 First edition January 2018 / PrioVino GmbH Reprint even in extracts only upon written permission by PrioVino GmbH (ISO

More information

Supplementary instructions. Air cooling - FIBERTRAC 31. Active air cooling system for radiation-based sensors. Document ID: 50339

Supplementary instructions. Air cooling - FIBERTRAC 31. Active air cooling system for radiation-based sensors. Document ID: 50339 Supplementary instructions Air cooling - FIBERTRAC 31 Active air cooling system for radiation-based sensors Document ID: 50339 Contents Contents 1 Product description 1.1 Configuration... 3 2 Mounting

More information

ASSEMBLY, USE AND MAINTENANCE ST 780 H ROTARY TEDDER

ASSEMBLY, USE AND MAINTENANCE ST 780 H ROTARY TEDDER ASSEMBLY, USE AND MAINTENANCE ST 780 H ROTARY TEDDER 05/2006 WARRANTY SITREX spa warrants new SITREX machinery at the time of delivery to the original purchaser to be free from defects in material and

More information

Spare parts list Inline filter FLND switchable

Spare parts list Inline filter FLND switchable Spare parts list Inline filter switchable to DIN 24550*, up to 400 l/min, up to 63 bar *Filters and fi lter elements also available in HYDAC dimensions 60 110 140 40 63 100 160 250 400 1. MAINTENANCE 1.1

More information

PLS / WPLS / PLV / PLS-HP / PLF-HP PLN / WPLN / WGN / PLFN PSN / PSFN PLE / WPLE / PLFE PLPE / WPLPE / PLHE

PLS / WPLS / PLV / PLS-HP / PLF-HP PLN / WPLN / WGN / PLFN PSN / PSFN PLE / WPLE / PLFE PLPE / WPLPE / PLHE Instruction Manual Standard Planetary Gearbox PLS / WPLS / PLV / PLS-HP / PLF-HP PLN / WPLN / WGN / PLFN PSN / PSFN PLE / WPLE / PLFE PLPE / WPLPE / PLHE GB_ 100225283 / Rev. Stand 004 www.zetek.ru +7(495)

More information

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference!

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference! Tension Meter FT Series S C H M I D T c o n t r o l i n s t r u m e n t s Edition FT 03.E Model FT Instruction Manual Valid as of: 01.09.2011 Please keep the manual for future reference! Contents 1 Warranty

More information

Operating instructions Spare parts list. Silage cutter

Operating instructions Spare parts list. Silage cutter Operating instructions Spare parts list Silage cutter 3 35 03 60 P 1287 EN Edition: 2010 Index Operation in accordance with specifications... 3 Safety technical advices... 4 Technical Data... 5 Description...

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation Globe control valve, pneumatically operated Actuator sizes 40 mm - 125 mm, Nominal diameter DN10-65 Kolbengesteuertes Geradsitzventil Antriebsgrößen 40 mm - 125 mm, Nennweiten DN10-65 Vanne à siège droit

More information

Inhalt. Granule jet blasting device PG 5 8. Owner s Manual. Translation of the original instructions

Inhalt. Granule jet blasting device PG 5 8. Owner s Manual. Translation of the original instructions Inhalt Granule jet blasting device PG 5 8 Owner s Manual Translation of the original instructions 1 This instruction manual is protected by copyright. No use outwith the strict limitations of copyright

More information

Turbocharger / A100-L Original assembly instructions English

Turbocharger / A100-L Original assembly instructions English Assembly Instructions Turbocharger / A100-L Original assembly instructions English This document is valid for the A100-L series: A165-L, A170-L, A175-L, A180-L, A185-L, A190-L Purpose The assembly instructions

More information

Instruction Manual. Magnetic Mixer MM UltraPure ESE01696-EN Original manual TD

Instruction Manual. Magnetic Mixer MM UltraPure ESE01696-EN Original manual TD Instruction Manual Magnetic Mixer MM UltraPure TD 531-001 ESE01696-EN5 2015-05 Original manual Table of contents The information herein is correct at the time of issue but may be subject to change without

More information

User manual. AGRETO Soil Compaction Tester AGRETO electronics GmbH

User manual. AGRETO Soil Compaction Tester AGRETO electronics GmbH User manual AGRETO Soil Compaction Tester 20.9.2017 AGRETO electronics GmbH Table of content 1 Introduction... 3 2 Scope of delivery... 3 3 Intended use... 3 4 Security... 4 5 Technical Specifications...

More information

OPE R AT O R S MANU A L QUICK-HITCH ADAPTER. 5BP (Field conversion kit)

OPE R AT O R S MANU A L QUICK-HITCH ADAPTER. 5BP (Field conversion kit) OPE R AT O R S MANU A L 5BP006750 (Field conversion kit) Manual 5BP97378B Date 06/8/05 SAFETY Take note! This safety alert symbol found throughout this manual is used to call your attention to instructions

More information

Turbocharger / TPS-H Original assembly instructions English

Turbocharger / TPS-H Original assembly instructions English Assembly Instructions Turbocharger / TPS-H Original assembly instructions English This document is valid for the TPS-H series: TPS44-H, TPS48-H, TPS52-H Purpose TPS-H turbocharger The assembly instructions

More information

Mod: KLD6-12/35XLAS-N

Mod: KLD6-12/35XLAS-N 12/2011 Mod: KLD6-12/35XLAS-N Production code: 1914070 INSTRUCTION MANUAL LOGIC LINE PLUS HOOD Reseller Stamp for Warranty Dear customer, Above all, thank you for choosing our product and we would like

More information

Operating and Maintenance Manual. for. HADEF overhead crane. as jointed crane TA

Operating and Maintenance Manual. for. HADEF overhead crane. as jointed crane TA 5.52.714.00.1.0 Edition 03.2004 GB Operating and Maintenance Manual for HADEF overhead crane as jointed crane TA Subject to changes. 1 HADEF Table of Contents 1 General Page 3 2 Product description Page

More information

Pressure relief valve

Pressure relief valve Pressure relief valve Operating manual Series DHV 712 Version BA-2015.10.20 EN Print-No. 300 510 TR MA DE Rev001 ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 32602 Vlotho Germany Phone: +49 (0) 5733-799-0

More information

JOHN DEERE Front Linkage Front PTO

JOHN DEERE Front Linkage Front PTO JOHN DEERE Front Linkage Front PTO Great technology for the work in the field Optimum quality latest technology compact design use worldwide SAUTER Conception Development, production, sales and technical

More information

LOG CHOP. Hydraulic Wood Guillotine. Owners Illustrated Instruction Book & Parts List

LOG CHOP. Hydraulic Wood Guillotine. Owners Illustrated Instruction Book & Parts List LOG CHOP Hydraulic Wood Guillotine Owners Illustrated Instruction Book & Parts List Grovebury Road, Leighton Buzzard, Bedfordshire. LU7 4UX. UK. Tel:01525 375157. Fax:01525 385222. Email: enquires@brownsagricultural.co.uk

More information

BEFCO. Operator s Manual BABY HOP & HOP FERTILIZER SPREADERS ACCESSORIES SIDE ROW DISCHARGE. AA4-120 (fits models Hop 209 & 212) DEFLECTOR

BEFCO. Operator s Manual BABY HOP & HOP FERTILIZER SPREADERS ACCESSORIES SIDE ROW DISCHARGE. AA4-120 (fits models Hop 209 & 212) DEFLECTOR BEFCO Operator s Manual BABY HOP & HOP FERTILIZER SPREADERS ACCESSORIES SIDE ROW DISCHARGE AA-0 (fits models Hop 09 & ) DEFLECTOR AA-0 (fits models Baby Hop 0 & 06) 009-95 (fits models Hop 0 & 06) 009-968

More information

Operating Instructions

Operating Instructions Operating Instructions Table of contents Table of contents... 1 1. Declaration... 1 2. Warranty and liability... 2 3. Gear description... 2 4. Gear types... 2 5. Safety... 3 5.1 General safety information...

More information

Assembly instructions

Assembly instructions Assembly instructions CP-Lube kit RX4,RX8,RX22,RX25,RX29,RX45,RX53 CP-Lube kit RX 4 CP-Lube kit RX 8 CP-Lube kit RX 22 CP-Lube kit RX 25 CP-Lube kit RX 29 CP-Lube kit RX 45 CP-Lube kit RX 53 Valid from

More information

Berta Flail Mower Attachment. BCS Power Units

Berta Flail Mower Attachment. BCS Power Units Manufactured by Berta s.r.l. to fit BCS Power Units Operating Instructions Before commissioning the machine, read operating instructions and observe warning and safety instructions. PLEASE ALSO READ ORIGINAL

More information

Supplementary instructions. Air cooling - FIBERTRAC 31 with Conduit tube connection. Active air cooling system for radiation-based sensors

Supplementary instructions. Air cooling - FIBERTRAC 31 with Conduit tube connection. Active air cooling system for radiation-based sensors Supplementary instructions Air cooling - FIBERTRAC 31 with Conduit tube connection Active air cooling system for radiation-based Document ID: 52847 Contents Contents 1 Product description 1.1 Configuration...

More information

Operating Instructions Declaration of Conformity Spare Parts List. Sub-Tiller 2.5 m / 3.0 m / 3.5 m / 4.0 m (rigid)

Operating Instructions Declaration of Conformity Spare Parts List. Sub-Tiller 2.5 m / 3.0 m / 3.5 m / 4.0 m (rigid) UK Operating Instructions Declaration of Conformity Spare Parts List Sub-Tiller 2.5 m / 3.0 m / 3.5 m / 4.0 m (rigid) Important: Before using the machine, please study the Operating Instructions thoroughly

More information

FLENDER ARPEX plate packs with conical bolting. ARP Size Assembly instructions AN 4256 en 07/2016. FLENDER couplings

FLENDER ARPEX plate packs with conical bolting. ARP Size Assembly instructions AN 4256 en 07/2016. FLENDER couplings FLENDER ARPEX plate packs with conical bolting ARP Size 325-6 Assembly instructions FLENDER couplings FLENDER ARPEX plate packs with conical bolting ARP Size 325-6 Assembly instructions Translation of

More information

Quiet Collector. Model No & Up

Quiet Collector. Model No & Up FORM NO. -8GB Rev A Quiet Collector Model No. 795-890000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety

More information

Shown on engine 904.9

Shown on engine 904.9 AR01.30-W-5800A Remove/install cylinder head 22.11.06 ENGINE 904.9 in MODEL 374, 375, 673, 674, 676, 958, 970, 972, 975, 976 ENGINE 906.9 in MODEL 374, 958, 970, 972, 974, 975, 976 ENGINE 906.9 in MODEL

More information

Installation and Operation Manual

Installation and Operation Manual Industrial Process Installation and Operation Manual Advantage Actuator 2.0 Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health and safety...2 Transportation

More information

Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 17 Engine-Lubrication system (Page GR-17)

Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 17 Engine-Lubrication system (Page GR-17) 17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pressure and oil pressure switch, checking Sump, removing and installing Valve gear, servicing (Page

More information

John Deere 4210, 4310, 4410 Soft Cab

John Deere 4210, 4310, 4410 Soft Cab John Deere 4210, 4310, 4410 Soft Cab Parts List & Mounting Instructions Jodale Perry Printed: 2004/08 Standard Parts List Qty Description Photo L&R Rear Brackets L&R Front Brackets 4 Front Bracket Spacers

More information

Instruction manual Hand-filing machine DIPROFIL FPT/ER and FPV/ER. Order no.: and

Instruction manual Hand-filing machine DIPROFIL FPT/ER and FPV/ER. Order no.: and Instruction manual Hand-filing machine DIPROFIL FPT/ER and FPV/ER Order no.: 0 005 204 and 0 005 208 1 List of contents 1 List of contents Page 02 2 Tips on using the manual Page 02 3 Safety instructions

More information

Catalyser Introduction. 3. Hazard Information. 2. Area of Application. 3.1 Symbology

Catalyser Introduction. 3. Hazard Information. 2. Area of Application. 3.1 Symbology ENGLISCH Catalyser 2300-0001 1. Introduction We are pleased with your decision to purchase the Catalyser. Please read the following operating instructions carefully and observe the safety information they

More information

Hand pump PUMP1000-4L-CONTROL. User manual

Hand pump PUMP1000-4L-CONTROL. User manual Hand pump PUMP1000-4L-CONTROL User manual Safety guidelines and symbols High product safety Follow instructions Definition of guidelines and symbols Warning Caution Our products correspond to the current

More information

1 General Purpose Contents Target group Entire documentation In case of questions...

1 General Purpose Contents Target group Entire documentation In case of questions... MHL350 D Contents General... 3. Purpose... 3. Contents... 3.3 Target group... 3.4 Entire documentation... 3.5 In case of questions... 3 Safety... 4. Requirements for the service staff... 4. General safety

More information

Remove and install steering gear

Remove and install steering gear ZF Aftermarket Neuwied Remove and install steering gear JRB5090 PUBLICATION XZB3502EN NOTE Secure vehicle against rolling away. Ensure proper cleanliness when working on the servo-steering. Cable connections

More information

John Deere 1420, 1435, 1445 Soft Side

John Deere 1420, 1435, 1445 Soft Side John Deere 1420, 1435, 1445 Soft Side Parts List & Mounting Instructions Jodale Perry Printed: 2003/07 Standard Parts List Qty Description Photo L&R L&R Rear Cab Brackets Rear Cab Side Panels (Plastic)

More information

John Deere 4510, 4610, 4710 Boxer

John Deere 4510, 4610, 4710 Boxer John Deere 4510, 4610, 4710 Boxer Parts List & Mounting Instructions Jodale Perry Printed: 2004/02 Standard Parts List Qty Description Photo L&R Rear Mounting Brackets (Upper&Lower) L&R Front Mounting

More information

Installation and Service Instructions (Translation of the Original Instructions) SV120. C _EN 11/2009 Rev.0

Installation and Service Instructions (Translation of the Original Instructions) SV120. C _EN 11/2009 Rev.0 Installation and Service Instructions (Translation of the Original Instructions) SV20 Introduction Carefully read these Installation and Service Instructions prior to the installation and start of operation

More information

KRIWAN Oil level regulators. Operating Instructions Accessories and Application Information

KRIWAN Oil level regulators. Operating Instructions Accessories and Application Information KRIWAN Oil level regulators Operating Instructions Accessories and Application Information Content General information... 4 Manufacturer...4 Storage information...4 Supplementary documents...4 List of

More information

Operating and Installation Instructions Swing Piston Compressors and Vacuum Pumps

Operating and Installation Instructions Swing Piston Compressors and Vacuum Pumps Operating and Installation Instructions Swing Piston Compressors and Vacuum Pumps UNPK04DC Pressure UNPK04DCB Pressure UNPK04DC Vacuum UNPK04DCB Vacuum KNF Neuberger, Inc 2 Black Forest Rd Trenton, NJ

More information

INSTRUCTION MANUAL. I/P Converter DSG BXXY3Z DSG BXXY4Z

INSTRUCTION MANUAL. I/P Converter DSG BXXY3Z DSG BXXY4Z INSTRUCTION MANUAL I/P Converter DSG BXXY3Z DSG BXXY4Z Revision 2.0 3.626 016136 en Page 1/15 Should you have any questions concerning the I/P converter, please contact the Service Department of the Product

More information

BoWex FLE-PA. BoWex FLE-PAC. KTR-N Sheet: Edition: EN 1 of BoWex FLE-PA / FLE-PAC Operating/Assembly instructions

BoWex FLE-PA. BoWex FLE-PAC. KTR-N Sheet: Edition: EN 1 of BoWex FLE-PA / FLE-PAC Operating/Assembly instructions 1 of 17 is a torsionally rigid flange coupling. It is able to compensate for shaft misalignment, for example caused by manufacturing inaccuracies, thermal expansion, etc. BoWex FLE-PA BoWex FLE-PAC Drawn:

More information

Spare Parts List Filter NFD Change-Over Version

Spare Parts List Filter NFD Change-Over Version Spare Parts List Filter Change-Over Version up to 1600 l/min, up to 5 bar 1340 640 540 7840 10440 1. MAINTENANCE GENERAL Please follow the maintenance instructions! 1. INSTALLATION Before fitting the filter

More information

80 Litre Suction Oil Drainer With Inspection Chamber

80 Litre Suction Oil Drainer With Inspection Chamber Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

Quick-Disconnect Coupling one-hand operation Push Pull ND 5, connecting thread G 1/4,max. operating pressure 500 bar

Quick-Disconnect Coupling one-hand operation Push Pull ND 5, connecting thread G 1/4,max. operating pressure 500 bar Issue 12-2013 Quick-Disconnect Coupling one-hand operation Push Pull ND 5, connecting thread G 1/4,max. operating pressure 500 bar Figure 1: Coupling complete Figure 4: Coded coupling, complete Table of

More information

INSPECTION FOR CORRECT VENTING OF THE OIL SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) SB R1 SB R1 MANDATORY

INSPECTION FOR CORRECT VENTING OF THE OIL SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) SB R1 SB R1 MANDATORY AIRCRAFT ENGINES SERVICE BULLETIN INSPECTION FOR CORRECT VENTING OF THE OIL SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) R1 R1 MANDATORY Repeating symbols: Please, pay attention to the following symbols

More information

FLENDER ARPEX Plate packs with close-fitting bolt connection. ARW-4 Sizes to Assembly instructions An 4239 en 12/2015.

FLENDER ARPEX Plate packs with close-fitting bolt connection. ARW-4 Sizes to Assembly instructions An 4239 en 12/2015. FLENDER ARPEX Plate packs with close-fitting bolt connection ARW-4 Sizes 101-4 to 292-4 Assembly instructions FLENDER couplings FLENDER ARPEX Plate packs with close-fitting bolt connection ARW-4 Sizes

More information

SERVICE INSTRUCTION PURGING OF LUBRICATION SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) SI SI Repeating symbols:

SERVICE INSTRUCTION PURGING OF LUBRICATION SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) SI SI Repeating symbols: SERVICE INSTRUCTION PURGING OF LUBRICATION SYSTEM FOR ROTAX ENGINE TYPE 9 AND 914 (SERIES) Repeating symbols: Please, pay attention to the following symbols throughout this document emphasizing particular

More information

OTTO HYDRAULICS GmbH & Co KG SYSTEME UND KOMPONENTEN FÜR ÖLHYDRAULISCHE ANTRIEBE UND STEUERUNGEN SIEMENSSTRASSE 12/ FRIEDRICHSHAFEN

OTTO HYDRAULICS GmbH & Co KG SYSTEME UND KOMPONENTEN FÜR ÖLHYDRAULISCHE ANTRIEBE UND STEUERUNGEN SIEMENSSTRASSE 12/ FRIEDRICHSHAFEN Hydraulik-aggregates Otto-Hydraulics Operating manual Author: Reinhard Otto Date: 16.01.2016 Operating manual rev.1 page: 1/11 Table of Contents Page 1...General information of this operating manual 3

More information

Operating instructions friction couplings ECS and ECSK

Operating instructions friction couplings ECS and ECSK Operating instructions friction couplings ECS and ECSK Contents 1. Assembly drawing 2. Construction and Function 2.1 Construction 2.2 Function 3. Dimensioning of the friction coupling 3.1 Choosing the

More information

FLENDER couplings. FLENDER ARPEX plate packs with conical bolting. ARS-6 sizes to K430 sizes 235 to 820

FLENDER couplings. FLENDER ARPEX plate packs with conical bolting. ARS-6 sizes to K430 sizes 235 to 820 FLENDER ARPEX plate packs with conical bolting ARS-6 sizes 255-6 to 722-6 K430 sizes 235 to 820 Operating instructions FLENDER couplings FLENDER ARPEX plate packs with conical bolting ARS-6 sizes 255-6

More information

USE AND MAINTENANCE MANUAL

USE AND MAINTENANCE MANUAL CLAMP FOR APPLIANCES ORIGINAL INTRODUCTION This manual contains instructions for assembly, periodic and extraordinary maintenance and troubleshooting. The instructions in this manual supplement, and do

More information

USER MANUAL. Keep this User Manual in the vehicle on which Halos are installed.

USER MANUAL. Keep this User Manual in the vehicle on which Halos are installed. Keep this User Manual in the vehicle on which Halos are installed. USER MANUAL 3 IMPORTANT SAFETY INFORMATION The Halo is not intended to replace regular pressure-checks and tire maintenance practices

More information

SBS Manual for the specialised craftsman. Filling and flushing station. Connection Operation. en Manual

SBS Manual for the specialised craftsman. Filling and flushing station. Connection Operation. en Manual SBS 2000 Filling and flushing station Manual for the specialised craftsman Connection Operation Thank you for buying this RESOL product. Please read this manual carefully to get the best performance from

More information

2003 Volkswagen Passat GL

2003 Volkswagen Passat GL 2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION

More information

Operating instructions. Grip fork FC

Operating instructions. Grip fork FC Operating instructions Grip fork FC 1 Danger Read the entire operating manual before using the front loader. 3 54 26 80 P 1524 EN Table of contents Operation in accordance with specifications... 3 Safety

More information

These operating instructions apply for: NCX 380 NCZ 300 NCX 480 NCZ 370 NCX 580 L NCZ 480 NCX 660 K NCZ 560 NCZ 660 NCZ 800

These operating instructions apply for: NCX 380 NCZ 300 NCX 480 NCZ 370 NCX 580 L NCZ 480 NCX 660 K NCZ 560 NCZ 660 NCZ 800 Original instructions Operating Instructions for May 2010 Electric Internal Vibrators BA No. 1092E Series NCX and NCZ These operating instructions apply for: NCX 380 NCZ 300 NCX 480 NCZ 370 NCX 580 L NCZ

More information

CAUTION. Fuel Injection Pump, In-Line, Spill Port Timing

CAUTION. Fuel Injection Pump, In-Line, Spill Port Timing Page 4 of 22 Rotate the crankshaft counterclockwise, as viewed from the front of the engine, to approximately 40 degrees before TDC. Both the RQV and RQV-K governor require the shutdown lever to be in

More information

Flexible Arm Stand F 360. User Manual

Flexible Arm Stand F 360. User Manual User Manual To ensure proper use of this instrument as well as to avoid injury while operating instrument, understanding this manual completely before use is highly recommended. Flexible Arm Stand User

More information

Assembly Instructions

Assembly Instructions Drive Technology \ Drive Automation \ System Integration \ Services *2450452_0617* Assembly Instructions Didactics - Gear Unit Technology Helical Gear Unit R57F AD2 Edition 06/2017 2450452/EN SEW-EURODRIVE

More information

Accumulator Charging Valve (Brake) - Test and Adjust

Accumulator Charging Valve (Brake) - Test and Adjust Testing and Adjusting 966G Series II Wheel Loader and 972G Series II Wheel Loader Braking System Accumulator Charging Valve (Brake) - Test and Adjust Table 1 Required Tools Part Number Description 1U-5481

More information

Competence from the Original Equipment Supplier

Competence from the Original Equipment Supplier Workshop Tips Competence from the Original Equipment Supplier GKN Driveline is the world s leading supplier of automotive driveline components and systems. Our global market leadership is based on a strong

More information

Bicolour level gauge. Type BU green/red. D-04-B EN-1 Edition 05/11

Bicolour level gauge. Type BU green/red. D-04-B EN-1 Edition 05/11 Bicolour level gauge Type BU green/red D-04-B-16615-EN-1 Edition 05/11 -itable of contents- 1. Health and safety instructions 4-5 1.1 General health and safety instructions...4 1.2 Unit-specific safety

More information

Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors

Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors Type range: UN813.3ANI UN813.4ANI UN813.3ANDCB UN813.4ANDCB UN813.5ANI Fig. 1: UN813.3ANI Fig. 2: UN813.4ANI You have selected

More information

Plunger Heads Use and Maintenance Manual

Plunger Heads Use and Maintenance Manual Plunger Heads Use and Maintenance Manual UK Positive displacement dosing pump Type PDP Series A-I 175 A-I 250 A-I 350 General instructions We thank you for choosing this product and recommend you read

More information

EPS 16 ATEX 1072 X, IECEx EPS X. Operating Instructions. Solenoid coil Type AC19 Magnetspule Typ AC19 Bobine magnétique Type AC19

EPS 16 ATEX 1072 X, IECEx EPS X. Operating Instructions. Solenoid coil Type AC19 Magnetspule Typ AC19 Bobine magnétique Type AC19 , IECEx EPS 16.0030X Solenoid coil Type AC19 Magnetspule Typ AC19 Bobine magnétique Type AC19 Device with II 2G/D Ex approval Geräte mit II 2G/D Ex Zulassung Appareils avec mode de protection II 2G/D Ex

More information

Operating Instructions

Operating Instructions Resistance Thermometer Clamp-on technology for temperature measurement on pipes, Type Series GA261x Operating Instructions 1 General Information... 2 1.1 General Safety Notes... 2 1.2 Intended Use... 2

More information

Pan and Tilt Head CDD2416-T

Pan and Tilt Head CDD2416-T Pan and Tilt Head CDD2416-T Installation guide Before attempting to connect or operate this product, please read these instructions completely Williams Electronics Ltd www.w-e.co.uk Tel: +44 (0)2921 660

More information