Accurate Labs, 311, 312 Govinda Complex, GIDC Char Rasta, Vapi, Valsad, Gujarat. Discipline Mechanical Calibration Issue Date
|
|
- Emerald Benson
- 5 years ago
- Views:
Transcription
1 Last Amended on - Page 1 of 9 I. DIMENSION 1. CALIPER $ Vernier L.C. 0.01mm 7.5 µm 9.0 µm Using Caliper Checker & Slip Gauges L.C. 0.05mm 29.5 µm 30.0 µm Dial / Electronic L.C. 0.02mm 12.5 µm 13.5 µm 2. HEIGHT Vernier L.C. 0.01mm Dial / Electronic L.C. 0.02mm 7.5 µm 9.0 µm 12.5 µm 13.5 µm Using Caliper Checker & Slip Gauges 3. EXTERNAL MICROMETER $ 0 to 25 mm 0 to 150mm 0 to 150mm >150mm to 600 mm 1.8 µm 2.0 µm 6.1 µm 7.3 µm Using Mick Check Set & Slip Gauges
2 Last Amended on - Page 2 of 9 4. DIAL GAUGE PLUNGER $ 0 to 10 mm 0 to 50 mm 1.0 µm 6.0 µm Using Single Axis 5. DIAL GAUGE LEVER TYPE $ 0 to 0.8 mm 0 to 1.6 mm 1.0 µm 6.0 µm Using Single Axis 6. BORE (For Plunger Movement only) 0 to 1 mm 0 to 1 mm 1.0 µm 5.8 µm Using Single Axis 7. PLAIN PLUG Up to 225 mm 1.26 µm Using Single Axis 8. PLAIN RING Up to 200 mm 2.53 µm Using Single Axis 9. SNAP Up to 150 mm 1.0 µm Using Single Axis
3 Last Amended on - Page 3 of DIAL SNAP Up to 150 mm 6.0 µm Using Slip Gauge 11. PISTOL CALIPER $ L.C mm Up to 150 mm 29.0 µm Using Slip Gauge 12. DIAL THICKNESS Up to 20 mm 5. 8 µm Using Slip Gauge 0 to 1 mm 1.0 µm 13. FEELER Up to 3 mm 2.15 µm Using Micrometer 14. MEASURING PIN Up to 20 mm 2.15 µm Using Micrometer 15. FOILS $ Up to 2 mm 2.15 µm Using Micrometer 16. LENGTH MEASURING MACHINE $ (Horizontal) L.C mm/ mm Upto 300 mm 1.3 µm Using O Grade Slip Gauge Set & Long Gauge Blocks
4 Last Amended on - Page 4 of STEEL SCALE $ Upto 1 mtr 32.0 µm Using Std Scale with DRO 18. MEASURING TAPE $ Upto 50 mtr 19. BEVEL PROTRACTOR $ L.C. 1' L.C. 5' 0 to 90 to 0 to 90 0 to 90 to 0 to L m 1000 Where L is in m 0.8 min 0.8 min Using Std Scale with DRO Using Angle Gauge 20. COATING THICKNESS Upto 1 mm 6.12 µm Using Standard Foils 21. THREAD PLUG Up to 225 mm 2.1 µm Using Single Axis as per IS: 2334:2001 IS:4218(part 1 to 5) 22. THREAD RING Up to 100 mm 1.4 µm Using Single Axis as per IS: 2334:2001 IS:4218(part 1 to 5)
5 Last Amended on - Page 5 of DEGREE PROTRACTOR $ 0 to 90 to 0 35 min Using Angle Gauge As per IS: 4239: COMBINATION SET $ 0 to 90 to 0 35 min Using Angle Gauge As per IS: 4239: PROFILE PROJECTOR/ OPTICAL MICROSCOPE VISION MEASURING MACHINE Linear X & Y Axis L.C /0.001/0.005mm Upto 200 mm 3.4 µm Using Slip Gauge Upto 200 mm 7.0 µm Angular L.C. 1 min of arc L.C. 5 min of arc 0 to to min of arc 5.0 min of arc Using Angle Gauge Block Magnification 10x to 100x 0.6% Using Glass Scale II. ACCELERATION & SPEED $ 1. SPEED (RPM) (Contact Type) 200 rpm to 5000 rpm 0.10 % rdg to 0.02 % rdg Using Photo Type Tachometer (Non Contact Type) 100 rpm to rpm 0.11 % rdg to 0.06% rdg Using Stroboscope By Direct Method
6 Last Amended on - Page 6 of 9 III. ACCOUSTIC $ 1. SOUND LEVEL METER 94 db & 114 db 0.7 db Using Sound Calibrator 2. SOUND CALIBRATOR 94 db 0.91 db Using Sound Level Meter IV. MASS 1. WEIGHTS $ (Conventional Mass) 1 mg 0.01 mg Using Standard Weights 2 mg 0.01 mg of E 2 (1mg to 200 g), F 1 5 mg 0.01 mg class (500 g to 10kg), 10 mg 0.01 mg M 1 Class (20kg) & 20 mg 0.01 mg weighing balance(s) 50 mg 0.01 mg with resolution of 100 mg 0.02 mg 0.01 mg (1mg to 50 g), 200 mg 0.02 mg 0.1 mg (100g & 200 g ), 500 mg 0.02 mg 1 mg ( 500 g & 1 kg), 1 g 0.02 mg 0.01 g (2 kg & 5 kg), & 2 g 0.02 mg 0.1g (10kg & 20 kg) 5 g 0.03 mg as per 10 g 0.03 mg OIML R 111: g 0.03 mg 50 g 0.04 mg 100 g 0.2 mg 200 g 0.2 mg 500 g 2 mg 1 kg 2 mg 2 kg 0.01 g 5 kg 0.02 g 10 kg 0.1 g 20 kg 0.4 g
7 Last Amended on - Page 7 of 9 2. WEIGHING BALANCE # (Electronic) 1 mg to 500 mg 0.09 mg Using Standard Weights 500 mg to 50 g 0.10 mg of E 2 (1mg to 200 g), F 1 50 g to 200 g 0.4 mg class (500 g to 10kg), 200 g to 1 kg g M 1 Class (20kg) 1 kg to 5 kg 0.05 g as per OIML R 76: kg to 10 kg 0.6 g 10 kg to 20 kg 0.8 g V. VOLUME $ 1. MICROPIPETTE (Piston Operated Pipette) 10 µl to 100 µl 100 µl to 1000 µl 0.02 µl 0.02 µl Using Standard weights of E 2 Class, weighing balance with resolution of 0.01mg & distilled water By Gravimetric Method as per ISO : LABORATORY GLASSWARE 1ml to 10 ml 0.04 µl Using Standard Weights o 10 ml to 50 ml 0.20 µl E 2 (1g to 200 g), 50 ml to 200 ml 0.3 µl F 1 class (500 g to 10kg), 200 ml to 1 L ml M 1 Class (20kg) & 1 L to 5 L 0.03 ml weighing balance(s) with 5 L to 20 L 0.4 ml resolution of 0.01 mg (1ml to 50 ml), 0.1 mg(>50 ml to 200 ml) 1 mg( >200 ml& 1 L), 0.01 g (>1L to 5 L), & 0.1g (>5 L to 20L) By Gravimetric method as per IS/ ISO 4787: 2010
8 Last Amended on - Page 8 of 9 VI. PRESSURE 1. PNEUMATIC DIAL PRESSURE GAUGES & DIGITAL PRESSURE GAUGES # 0 to 30 bar 0 to 560 mmwc bar 0.45 mmwc Using Digital pressure gauge with pneumatic pump By Comparison method as per DKD-R HYDRAULIC DIAL PRESSURE GAUGES & DIGITAL PRESSURE GAUGES $ 0 to 60 bar 0 to 1000 bar 0.12% rdg 0.15% rdg Using Hydraulic Dead Weight Tester By Direct method as per DKD-R bar to 200 bar 0.12 bar Using Digital pressure gauge with hydraulic pump By Comparison method as per DKD-R HYDRAULIC DIAL PRESSURE GAUGES & DIGITAL PRESSURE GAUGES 30 bar to 300 bar 0.27 bar Using Digital pressure gauge with hydraulic pump By Comparison method as per DKD-R-6-1
9 Last Amended on - Page 9 of 9 VII. VACUUM # 1. DIAL GAUGES & DIGITAL VACUUM GAUGES -0.9bar to 0 bar bar Using Digital Vacuum gauge with hydraulic pump By Comparison method as per DKD-R-6-1 * Measurement Capability is expressed as an uncertainty ( ) at a confidence probability of 95% $ Only in Permanent Only for Site Calibration # The laboratory is also capable for site calibration however, the uncertainty at site depends on the prevailing actual environmental conditions and master equipment used.
Institute for Design of Electrical Measuring Instruments, Swatantryaveer Tatya Tope Marg, Chunabhatti, Sion, Mumbai, Maharashtra
Last Amended on 02.09.2014 Page 1 of 10 I. DIMENSION 1 Calipers $ Up to 600 mm 10.4 µm Using Caliper Checker by Up to 1000 mm 13.2 µm Using Long Slip Gauge by 2 Height Gauges $ Up to 600 mm 12.8 µm Using
More informationDiscipline Mechanical Calibration Issue Date Certificate Number C-0393 Valid Until Last Amended on - Page 1 of 6
Last Amended on - Page 1 of 6 I. DIMENSION 1. Vernier Caliper (Digital/ Dial/ Scale) $ L.C.: 0.01 mm 0 to 150 mm 7.7 µm Using Caliper Checker 0 to 200 mm 8.1 µm 0 to 300 mm 9.3 µm 0 to 600 mm 13.9 µm 2.
More informationA.A. Calibration Pvt. Ltd., 13-C/18, Vasundhara Haat, Vasundhara, Ghaziabad, Uttar Pradesh. Discipline Mechanical Calibration Issue Date
Last Amended on 02.09.2014 Page 1 of 10 I. DIMENSION 1. VERNIER CALIPER $ L.C. 0.01mm 0 to 300 mm 0 to 600 mm 0 to 1000 mm 8 µm 14 µm 16 µm, Slip Gauge Accessories, Gauge Block L.C. 0.02 mm 0 to 1500 mm
More informationAlcalab Private Limited, 3rd Floor, Ashiana Trade Centre, Adityapur, Jamshedpur, Jharkhand. Discipline Mechanical Calibration Issue Date
Last Amended on - Page 1 of 11 I. DIMENSIONS 1. SLIP 0.5 mm to 25 mm 0.25 μm Using Slip Gauge (K-Grade) & > 25 mm to 50 mm 0.34 μm Double Probe Comparator > 50 mm to 75 mm 0.46 μm > 75 mm to 100 mm 0.58
More informationCalitron Calibration Laboratory, U1: 207, Kohinoor Arcade, Tilak Chowk, Nigdi, Pune, Maharashtra
Last Amended on 12.09.2014 Page 1 of 7 I. MASS 1. Weights $ (Conventional Mass) 1 mg 0.015 mg Using Weights of 2 mg 0.015 mg accuracy Class F1 and 5 mg 0.015 mg 10 mg 0.015 mg 20 mg 0.020 mg 50 mg 0.020
More informationDiscipline Mechanical Calibration Issue Date Certificate Number C-0208 Valid Until Last Amended on
Last Amended on 12.08.2016 Page 1 of 7 I. DIMENSION (Basic Measuring, Gauge etc.) 1. CALIPER $ (Vernier / Dial / Digital) L.C.: 10 µm ф L.C.: 50 µm ф Upto 600mm 13 m Using Gauge Block Set Grade 0 (Carbide);
More informationDiscipline Mechanical Calibration Issue Date Certificate Number C-0752 Valid Until Last Amended on - Page 1 of 6
Last Amended on - Page 1 of 6 I DIMENSION 1. Caliper $ (Vernier/Dial/Digital) LC : 0.01mm 0 to 600 mm 0 to 1000 mm 12.2 µm 13.3 µm Using Caliper Checker, Slip Gauge Block & 2. Depth Caliper $ (Vernier/Dial/Digital)
More informationHi-Tech Calibration, 307, 3rd Floor, Govinda Complex, Char Rasta, Vapi, Gujarat. Discipline Mechanical Calibration Issue Date
Last Amended on 18.01.2016 Page 1 of 7 I. DIMENSIONS 1. CALIPER $ (Vernier, Dial, Electronics) L.C.0.01 mm up to 1000mm 24 µm Using Caliper Checker / L.C.0.02 mm up to 600mm 19 µm Length Bars /Slip Gauges
More informationAccurate Measurements, Plot No.103, D Block, Meethapur Ext., Badarpur, New Delhi. Discipline Mechanical Calibration Issue Date
Last Amended on 11.11.2014 Page 1 of 6 I. DIMENSION 1. Dial/ Digital Vernier Caliper $ L.C.: 0.01mm Φ 0 to 200 mm 7.5 µm Using Slip Gauge Set & L.C.: 0.01mm Φ 0 to 300 mm 12.17 µm Using Slip Gauges & Caliper
More informationCentral Mechanical Engineering Research Institute, Mahatma Gandhi Avenue, Durgapur, West Bengal
Last Amended on 23.09.2014 Page 1 of 9 I. DIMENSION 1. GAUGE BLOCKS $ 0.5 mm to 25 mm 25 mm to 50 mm 50 mm to 75 mm 75 mm to 100 mm 2. LENGTH BAR $ Upto 300 mm 300 mm to 600 mm 300 mm to 1000 mm 0.11µm
More informationDiscipline Mechanical Calibration Issue Date Certificate Number C-0751 Valid Until Last Amended on
Last Amended on 10.03.2016 Page 1 of 5 I. DIMENSION 1. Vernier caliper $ 0 to 300 mm/0.01 mm ± 12.0 µm Using Caliper Checker 0 to 300 mm/0.02 mm ± 16.1 µm Using Caliper Checker 0 to 600 mm/0.01 mm ± 14.0
More informationCal-Tech Calibration Services Pvt. Ltd., Flat No.8, Avadhut Heights, Anand Nagar, Sinhgad Road, Pune, Maharashtra
Last Amended on - Page 1 of 5 I. DIMENSION 1. CALIPER $ L.C. :-10 µm 0 to 300 mm 12.0 µm Using Caliper Checker; Gauge 0 to 1000 mm 12.0 µm Block Set L.C. :-20 µm 0 to 600 mm 16.0 µm 0 to 1000 mm 20.0 µm
More informationCaliber Gauges & Instruments Laboratory, S. No. 14/1, Dattadigamber Soc. B, Warje Jakat Naka, Pune, Maharashtra
Last Amended on - Page 1 of 10 I. DIMENSION (Basic Measuring, Gauge etc.) 1. PLAIN PLUG / WIDTH/ DEPTH/ Upto 100 mm 1.9 µm Using Electronic FLUSH PIN GAUGE DIAMETER /WIDTH / DEPTH $ 100 mm to 300 mm 3.8
More informationQ-Tech Engineering Services, S-134, C/o, Precision Engineering Works, MIDC, Bhosari, Pune, Maharashtra
Last Amended on 24.05.2015 Page 1 of 5 I. DIMENSION 1. EXTERNAL MICROMETER $ L.C. 1 µm Φ >100 mm to 300 mm 1.4 µm 3.0 µm Using Slip Gauge Blocks Gr '0' / Long Slip Gauges, by Comparison 2. DEPTH MICROMETER
More informationQA Tech (A Division of GMP Technical Solutions Pvt. Ltd.), L-73, Verna Industrial Estate, Verna Salcette, Goa
Last Amended on - Page 1 of 5 I. DIMENSION 1. CALIPER $ L.C. :-10µm Φ 0 to 300 mm 13 µm Using Caliper Checker; & T.C. Gauge Block Set by Comparison L.C. :- 20µm 0 to 1000 mm 22 µm Using Caliper Checker;
More informationICL Calibration And Testing Services, SCO - 37, Ground Floor, Sector-12, Panchkula, Haryana. Discipline Mechanical Calibration Issue Date
Last Amended on 09.12.2016 Page 1 of 8 I. DIMENSION (Basic Measuring, Gauge etc.) 1 LENGTH GAUGE/SETTING ROD $ Up to 100 mm >100 mm to 500 mm 1.5 µm 7.20 µm Using ULM, Gauge Block grade- 0 & Electronic
More informationAutocal Solutions Pvt. Ltd., Plot No. BG-74, Gala No. 1 & 2, Jai Tulja Bhavani Indl. Premises, Telco Road, MIDC Bhosari, Pune, Maharashtra
Last Amended on - Page 1 of 5 I. DIMENSION 1. CALIPER (Vernier/Dial/Digital) L. C. : 10µm Φ 0 to 600 mm 16 µm Using Caliper Checker & External Micrometer by 2. DEPTH GAUGE (Vernier/Dial/ Digital) L. C.
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that SP Metrology System Thailand Co., LTD 88/115
More informationShriram Institute For Industrial Research, 14-15, Sadarmangala Industrial Area, Whitefield Road, Bangalore, Karnataka
Certificate Number CC-2083 (in lieu of C-0216, C-0304, C-1497) Page 1 of 7 ELECTRO-TECHNICAL CALIBRATION I. MEASURE 1. Time $ 5 sec to 9900 sec 0.12 sec to 5.8 sec Using Digital Time Totalizer (Digital
More informationSchedule. 200 C to 400 C. 400 C to 660 C C to 800 C C to 1300 C C to 1200 C. 0 C to 1700 C. 0 C to 1700 C.
Page: 1 of 9 LABORATORY LOCATION: (PERMANENT LABORATORY) PPCALIBRATION SERVICES SDN. BHD. NO. 15, MEDAN BUKIT EMAS PUSAT PERNIAGAAN BUKIT EMAS 14000 BUKIT MERTAJAM, PULAU PINANG MALAYSIA This laboratory
More informationPage : 1 of 16. FIELD OF TESTING : Calibration and Measurement CALIBRATION & MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINITY *
Metrix Precision Pte Ltd Certificate No. : LA-2014-0581-C No. 23 Tagore Lane #02-03/04 Tagore 23 Warehouse Issue No. : 2 Singapore 787601 Date : 29 July 2016 FIELD OF TESTING : Calibration and Measurement
More informationSchedule. 300 mm to 600 mm 600 mm to 1000 mm inch to 12 inch
LABORATORY LOCATION: (PERMANENT LABORATORY) MITUTOYO (M) SDN. BHD. MAH SING INTEGRATED INDUSTRIAL PARK BANDAR PINGGIRAN SUBANG 4, JALAN UTARID U5/14, SECTION U5 40150 SHAH ALAM SELANGOR, MALAYSIA Page:
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 ALDINGER COMPANY 1440 Prudential Drive Dallas, TX 75235 Timothy R. Detten Phone: 214 638 1808 CALIBRATION Valid To: July 31, 2018 Certificate
More informationRev /07/2015 CATALOGUE - CALIBRATION SERVICES 1
Rev. 02 07/07/2015 CATALOGUE - CALIBRATION SERVICES 1 OVER 100 ITEMS We are proud to present to you our new catalogue for 2015. In the following pages we present more than 100 instrument types, which we
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
Schedule of ccreditation United Kingdom ccreditation Service Issue No: 028 Issue date: 10 pril 2018 ccredited to 6 Banner Park Wickmans Drive Coventry CV4 9X Contact: Keith rnold Tel: +44 (0)2476 426 316/317
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
Schedule of ccreditation United Kingdom ccreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK ccredited to Laboratory locations: Unit 9 G B Quality ssurance (Consultants)
More informationMetrology Laboratory, CMTI, Central Manufacturing Technology Institute, Tumkur Road, Bangalore, Karnataka Accreditation Standard ISO/IEC 17025: 2005
aboratory Metrology aboratory, CMTI, Central Manufacturing Technology ast Amended on 22.09.2016 Page 1 of 15 I. DIMENSION (Basic Measuring, Gauge etc.,) 1. ANGE GAUGE BOCKS $ 0 to 90 2.8 arc sec Using
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 RIVERVIEW CALIBRATION SERVICES, LTD 5706 Veto Road Belpre, OH 45714 J. Michael Pennell Phone: 740 678 8625 CALIBRATION Valid To: July
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
Schedule of ccreditation United Kingdom ccreditation Service ccredited to Division of Cromwell Tools Ltd Services Block 65 Chartwell Drive Wigston Leicester LE18 2FS Contact: Mr T still Tel: +44 (0)116-2572396
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Garber Metrology Weighing Solutions & Precision
More informationPrice List. Calibration Fee
3/4-5 Moo 3, Klong 5, Klong Luang, Pathumthani, 110, Thailand Tel. +66 577 5100 (Please contact : Customer Service Section Ext. 3101, 310) Fax. +66 577 3659 E-mail : cs@nimt.or.th Website : http://www.nimt.or.th
More informationStandard Scales SERIES 182 Made of Low-Expansion Glass. Working Standard Scales SERIES 182 E-32
Standard Scales SERIES 182 Made of Low-Expansion Glass High-precision glass scales manufactured under Mitutoyo s leading-edge Linear Scale production technology. High accuracy is guaranteed to be used
More informationHellenic Accreditation System. Annex F2/17 to the Certificate No SCOPE of ACCREDITATION
Hellenic Accreditation System Annex F2/17 to the Certificate No. 263-5 SCOPE of ACCREDITATION of the Testing & Calibration Laboratory of LINK LAB LTD for the performance of calibrations Measurand / Spectrophotometric
More informationWelcome to Garber C O R P O R AT E O V E R V I E W
CORPORATE OVERVIEW Garber Metrology is one of the only companies in the Mid-Atlantic Region that combines full service weighing solutions, a wide range of calibration /metrology services and a broad scope
More informationHeight Master Page 345. Check Master Page 349. Calibration Tools Page 354
Calibration Instruments Height Master Page 345 Check Master Page 349 Calibration Tools Page 354 344 Digital Height Master Functions ZERO/ABS DATA/HOLD Auto Power OFF after 20 min. non use Low voltage alarm
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 NORTHERN BALANCE AND SCALE, INC. 9556 W. Bloomington Freeway Bloomington, MN 55431 Joey Kaluser Phone: 952 881 7716 CALIBRATION Valid
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Monterrey, Nuevo León, 64920 (Hereinafter called the
More information+91-8048600379 Rampura Tools http://www.rampuratools.in/ We are one of the leading distributor, suppliers and traders of Measuring Instrument. Owing to their accurate measurement, sturdy construction,
More informationMeasuring. Affordable. Effective. Instruments
Measuring Effective Affordable Instruments 2 Electronic Calipers 00534002 00534003 00534020 n Stainless steel frame n Thumb wheel for rapid setting n Direct Metric/Inch conversion n Accuracy to 0,02 mm
More informationTEST AND CALIBRATION SERVICES Ensuring quality and reliability.
> TEST AND CALIBRATION SERVICES Ensuring quality and reliability www.thalesgroup.com.au TEST AND CALIBRATION SERVICES ENSURING QUALITY AND RELIABILITY Introduction Thales Australia s Test and Calibration
More informationIEC SYSTEM FOR CONFORMITY TESTING AND COMMITTEE OF TESTING LABORATORIES CERTIFICATION OF ELECTRICAL EQUIPMENT
IEC SYSTEM FO CONFOMITY TESTING AND CETIFICATION OF ELECTICAL EQUIPMENT COMMITTEE OF TESTING LABOATOIES =equired by Lab S=May be subcontracted TESTING AND MEASUING EQUIPMENT/ALLOWED SUBCONTACTING Power
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 Unit 3 24-26 Boulton Road Stevenage Hertfordshire SG1 4QX ontact: Mr G J Wilson Tel: +44 (0) 1438 900080 Fax: +44 (0) 1438
More informationAnnex to the Accreditation Certificate D-K according to DIN EN ISO/IEC 17025:2005
Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-K-15102-01-00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 05.07.2017 to 04.07.2022 Date of issue: 05.07.2017
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Torreón, Coahuila, México C.P. 27019 (Hereinafter
More informationCALIBRATION SYSTEM CERTIFICATE
CALIBRATION SYSTEM CERTIFICATE With respect to products (measuring instruments and testing instruments), we hereby certify that we have established our calibration system traceable to the national (international)
More informationScope of Accreditation For Global Instrumentation Services, LLC 523 N. Sam Houston Parkway E, Suite 230 Houston, TX Gavin Lewis
Scope of Accreditation For Global Instrumentation Services, LLC 523 N. Sam Houston Parkway E, Suite 230 Houston, TX 77060 Gavin Lewis 832-428-2737 In recognition of a successful assessment to ISO/IEC 17025:2005
More informationPROMPT ENGINEERING P.O. BOX BARWA VILLAGE, WAKRA, BUILDING NO. 6 SHOP NO. 19 AND 20 DOHA QATAR
This is to attest that PROMPT ENGINEERING P.O. BOX 24067 BARWA VILLAGE, WAKRA, BUILDING NO. 6 SHOP NO. 19 AND 20 DOHA QATAR Calibration Laboratory CL-165 has met the requirements of AC204, IAS Accreditation
More informationTopPette Mechanical Pipettes
TopPette Mechanical Pipettes Features for TopPette - Lightweight, ergonomic, low force design - Digital display clearly reads volume setting - The pipettes cover volume range of 0.1μl to 10ml - Easy to
More information+91-8048718949 Bearing & Tools Centre http://www.measuringtestinginstrument.com/ We are a renowned dealer and supplier of a wide assortment of precision engineered testing and measuring equipment. Our
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 EMPIRE SCALE CORPORATION d.b.a. PRECISION SCALE & BALANCE d.b.a. EMPIRE SCALE & BALANCE 140 Rotech Drive Lancaster, NY 14086 Margery
More informationRef:CL/Mech./ Cal /BID-01(13-14) Date: 10 July 2013
Ref:CL/Mech./ Cal /BID-0(3-4) Date: 0 July 203 SUBJECT: Procurement of Calibration Services for the Equipments in Central Laboratory (Mechanical). Dear Sirs, Technical & Commercial Bids are invited for
More informationACCREDITATION FACILITY AUDIT CHECKLIST
ACCREDITATION FACILITY AUDIT CHECKLIST Institution Name: Date: Designated Trade: Marine and Outdoor Power Equipment Technician AC #: Contact: Location: Course Duration: of weeks: of hours total: of hours
More informationTransferpette. Testing Instructions (SOP) 1. Introduction. May 2009
Transferpette Testing Instructions (SOP) May 2009 1. Introduction The standards DIN EN ISO 8655 describe both the design and the testing of the piston operated pipette Transferpette. The following Testing
More informationDepartment of Mechanical Engineering ME6513 - METROLOGY AND MEASUREMENT LAB LABORATORY MANUAL Name Register No. Branch Year & Semester : : : : 1 CONTENTS S.NO. DATE EXPERIMENT NAME PAGE NO. 1 Calibration
More informationRotary Positioning Stages Introduction
Introduction Features Aluminum/steel construction Protective black anodize finish Low-friction rotary adjustment Precise/accurate movement Trouble-free operation aedal precision rotary stages are utilized
More informationCarl Stuart Ltd. Tallaght Business Park, Whitestown, Dublin 24. Calibration Laboratory Registration number: 270C
Tallaght Business Park, Whitestown, Dublin 24 Calibration Laboratory Registration number: 270C is accredited by the Irish National Board (INAB) to undertake calibration as detailed in the Schedule bearing
More informationUGANDA NATIONAL BUREAU OF STANDARDS NATIONAL METROLOGY LABORATORY
CALIBRATION CHARGES Page 1 of 5 In the derivation of calibration charges a number of factors have been taken into consideration. These include the following; 1. Personnel Salaries and man-hours for calibration
More informationThis annex is valid from: to Replaces annex dated: Location(s) where activities are performed under accreditation
Chamber Commerce: 06073326 Location(s) where activities are performed under accreditation ad Office Smaragdstraat 7 7554 TD ngelo OV The Netherlands Location Abbreviation/ location Smaragdstraat 7 7554
More informationTRI-STATE INSTRUMENT SVC, INC
CALIBRATION RATE POLICY AND PRICING 2017 Typically, compliance with ISO-900x and TS 16949 specifications require LONG FORM calibration reports in the following formats. Format #1 -- Before Adjustment or
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2017. Data Weighing Systems 255 Mittel Drive Wood Dale, IL Steven A. Thomas CALIBRATION
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017 Data Weighing Systems 255 Mittel Drive Wood Dale, IL 60191 Steven A. Thomas 800-397-6301 CALIBRATION Valid to: September 22, 2019 Certificate Number: L1114-1
More informationPage 1 of 5. United Testing Systems, Inc S. Acacia Avenue Fullerton, CA William Warner, Quality Manager
IAS Accreditation Number Accredited Entity Address CL-128 1375 S. Acacia Avenue Fullerton, CA 92831 William Warner, Quality Manager Contact Name Telephone +1 (714) 638-2322 Effective Date of Scope July
More informationVITLAB Dispenser. Standard Operating Procedure (SOP)
VITLAB Dispenser Standard Operating Procedure (SOP) VITLAB GmbH Linus-Pauling-Str. 63762 Grossostheim Germany tel: +49 6026 97799-0 fax: +49 6026 97799-30 info@vitlab.com www.vitlab.com Table of contents.
More informationSCOPE OF ACCREDITATION TO ISO/IEC & KS Q ISO/IEC
SCOPE OF ACCREDITATION TO ISO/IEC 17025-2005 & KS Q ISO/IEC 17025-2006 Korea Instrument Co., Ltd. Branch 45, Gwangjang-ro 56beon-gil, Sasang-gu, Busan 46976 Phone : 051-322-0880, Fax : 051-322-4066, E-mail
More informationSmall Tool Instruments and Data Management
Small Tool Instruments and Data Management Gauge Blocks Pages 302 311 Calibration instruments Pages 312 319 301 Basic information on gauge blocks Characteristics of Mitutoyo gauge blocks: Mitutoyo, at
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 CAL-RITE CORPORATION 1665 Quincy Avenue, Suite 103 Naperville, IL 60540 Michael Crosby Phone: 630 355 1522 CALIBRATION Valid To: December
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORYACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationSmall Tool Instruments and Data Management
Small Tool Instruments and Data Management Dial Gauge Stands Pages 268 272 Comparator Stands Pages 273 274 Joint Magnetic Stands Concentricity testers Pages 275 280 Angulometers, steel squares Pages 281
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 METTLER TOLEDO (INDUSTRIAL) 1900 Polaris Parkway Columbus, OH 43240 Frank Gardone Phone: 412 213 2263 CALIBRATION Valid To: April 30,
More informationFaculty of Mechanical Engineering B.E. Mechanical Engineering (Sandwich) (R 2013) Semester III. Requirements for a batch of 30 students
Sl. No. Faculty of Mechanical Engineering (R 203) Semester III CE635 STRENGTH OF MATERIALS LABORATORY (R) (A) Deficiency (R - A). Universal Tensile Testing machine with double shear attachment 40 Ton Capacity
More informationTransferpette. Testing Instructions (SOP) 1. Introduction. October 2013
Transferpette Testing Instructions (SOP) October 2013 1. Introduction The standards DIN EN ISO 8655 describe both the design and the testing of the piston operated pipette Transferpette. The following
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Mexical Metrología, S.A. de C.V. Tecnología de Materiales,
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationAccredited Laboratory
Accredited Laboratory A2LA has accredited CAL-RITE CORPORATION Naperville, IL for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International
More informationShawal CGC Calibration Profile
Shawal CGC Calibration Profile Phone Number: +93 700021925, +93 748468800, +93 779015120 TABLE OF CONTENTS 1.0. INTRODUCTION 2.0 COMPANY STRUCTURE 3.0 CALIBRATION & EQUIPMENT & REPAIR SERVICES 4.0 COMPETITIVE
More informationCatalog # Meeting Your Metrology Needs. A.A. Jansson, Inc. Precision Measuring Service and Equipment
Catalog #10046 2017 Meeting Your Metrology Needs A.A. Jansson, Inc. Precision Measuring Service and Equipment Our Place in History C.E. Johansson, Father of Measurement, of Eskilstuna, Sweden, devoted
More informationDYNAMICS LABORATORY. AIM: To apply the knowledge gained in kinematics and dynamics of machines to real system.
DYNAMICS LABORATORY AIM: To apply the knowledge gained in kinematics and dynamics of machines to real system. OBJECTIVES: To supplement the principles learnt in kinematics and Dynamics of Machinery. To
More informationCALIBRATION PRICE LIST
THREADED API STANDOFF SIZE SPEC 5 LINE PIPE $95 ea $150 ea 1/8 4 working 5 12 working $180 ea $290 ea $190 set 1/8 12 masters TUBING (UPTBG & TBG) (EUE & NUE) (1.0500 4 ½ ) $125 ea $190 set Working Masters
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 QUALITY CONTROL SERVICES, INC. 2340 SE 11 th Avenue Portland, OR 97214 George Cahill Phone: 503 236 2712 CALIBRATION Valid To: September
More informationNADAR SARASWATHI COLLEGE OF ENGINEERING AND TECHNOLOGY VADAPUDUPATTI, THENI DEPARTMENT OF MECHANICAL ENGINEERING LAB FACILITIES
NADAR SARASWATHI COLLEGE OF ENGINEERING AND TECHNOLOGY VADAPUDUPATTI, THENI DEPARTMENT OF MECHANICAL ENGINEERING LAB FACILITIES S.No 1 Name of the Laboratory ENGINEERING PRACTICES Total Area of Lab 62.0
More informationSVENSK STANDARD SS-EN ISO Volymetrisk mätapparatur med kolv Del 6: Gravimetriska metoder för bestämning av mätfel (ISO :2002)
SVENSK STANDARD SS-EN ISO 8655-6 Fastställd 2003-03-28 Utgåva 1 Volymetrisk mätapparatur med kolv Del 6: Gravimetriska metoder för bestämning av mätfel (ISO 8655-6:2002) Piston-operated volumetric apparatus
More informationGear Measurement. Lecture (7) Mechanical Measurements
18 3. Gear profile checking 2. Involute measuring machine In this method the gear is held on a mandrel and circular disc of same diameter as the base circle of gear for the measurement is fixed on the
More informationINSPECTION. (b) Using a wire brush, remove all the carbon from the combustion NOTICE:
EM44 ENGINE MECHANICAL (2RZFE, 3RZFE) INSPECTION EM16R02 1. CLEAN TOP SURFACES OF PISTONS AND CYL- INDER BLOCK (a) Turn the crankshaft, and bring each piston to top dead center (TDC). (b) Using a gasket
More informationIII EC6362 ELECTRONIC CIRCUITS AND DIGITAL LABORATORY
Sl No Faculty of Mechanical Engineering BE Robotics and Automation (R 2013) Semester III EC6362 ELECTRONIC CIRCUITS AND DIGITAL LABORATORY 1 0 30V RPS 12 2 0 50V RPS 2 3 0 5V RPS 2 4 0 30V Voltmeter 10
More informationANAUM INTERNATIONAL ELECTRONICS LLC. Test and Measurement Calibration Services Test Bench.
ANAUM INTERNATIONAL ELECTRONICS LLC Test and Measurement Calibration Services Test Bench www.anaum.ae About Us Located in the Musaffah, Abu Dhabi, United Arab Emirates, Anaum International Electronics
More informationGauge Blocks - Reference for Precision
ß Measuring and Laying-Out Tools, Testing Instruments Gauge Blocks - Reference for Precision Parallel gauge blocks in compliance with DIN EN ISO 650 are supplied in the following calibration and tolerance
More informationCalibration Laboratory Assessment Service CLAS Certificate Number Page 1 of 5
National Research Council Conseil national de recherches Canada Canada Measurement Standards and Science Science des mesures et étalons Calibration Laboratory Assessment Service CLAS Certificate Number
More information1P D 6681 Final Report Cover Sheet
D 6681 Final Report Cover Sheet Method Version Conducted For V = Valid I = Invalid N = Results Cannot be Interpreted as Representative of Oil Performance (Non- Reference Oil) and Shall Not be Used in Determining
More informationP5510. Users Manual. Pneumatic Comparison Test Pump. Test Equipment Depot Washington Street Melrose, MA TestEquipmentDepot.
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com P5510 Pneumatic Comparison Test Pump Users Manual PN 3952297 November 2010 2010 Fluke Corporation. All
More informationINSPECTION. (b) Clean the combustion chambers. Using a wire brush, remove all the carbon from the combustion NOTICE:
ENGINE MECHANICAL (2JZGE) INSPECTION EM41 EM0DC05 1. CLEAN TOP SURFACES OF PISTONS AND CYL- INDER BLOCK (a) Turn the crankshaft, and bring each piston to top dead center (TDC). Using a gasket scraper,
More informationBRAKE BOOSTER. Section 5. Brake Booster. Construction. Single Diaphragm Booster
BRAKE BOOSTER Brake Booster The brake booster is designed to create a greater braking force from a minimum pedal effort, using a difference in atmospheric pressure and the engine s manifold vacuum. It
More informationHA Thickness Gauge IS:2386 (part 1)- 1963
AGGREGATE TESTING HA50.05 Mechanical Rotating Sample Divider (Motorised) IS : 1607-1960 For obtaining representative sample for sieve analysis. It is suitable for dry sands, fine powders, ores, refractory
More informationSAMPLES GAUGES. Tolerances OUR SPECIAL OFFER: PLUG GAUGES WITH REQUIRED FIT OR INDIVIDUAL TOLERANCES ACCORDING TO YOUR SPECIFICATIONS
SAMPLES GAUGES PLUG GAUGES Tolerances GO side Fit NO GO side OUR SPECIAL OFFER: PLUG GAUGES WITH REQUIRED FIT OR INDIVIDUAL TOLERANCES ACCORDING TO YOUR SPECIFICATIONS BESTSELLER: FEELER GAUGE TAPES IN
More informationOVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.
4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT
More informationLecture (7) on. Gear Measurement. By Dr. Emad M. Saad. Industrial Engineering Dept. Faculty of Engineering. Fayoum University.
1 Lecture (7) on Gear Measurement Fayoum University By Dr. Emad M. Saad Industrial Engineering Dept. Faculty of Engineering Fayoum University Faculty of Engineering Industrial Engineering Dept. 2015-2016
More informationRe: Extension for ISO/IEC 17025: 2005 accreditation Certificates #ACT-1997, ACT , ACT & AT
October 17, 2017 VIA EMAIL Link Engineering Company Jim Villella 401 Southfield Road Dearborn, MI 48120 Re: Extension for ISO/IEC 17025: 2005 accreditation Certificates #ACT-1997, ACT-1997.01, ACT-1997.02
More informationINSPECTION. (b) Using a wire brush, remove all the carbon from the combustion NOTICE:
EM38 ENGINE MECHANICAL (5VZFE) INSPECTION EM16E02 1. CLEAN TOP SURFACES OF PISTONS AND CYL- INDER BLOCK (a) Turn the crankshaft and bring each piston to top dead center (TDC). (b) Using a gasket scraper,
More informationADJUSTING VALVE CLEARANCE
ADJUSTING VALVE CLEARANCE ADJUSTING VALVE CLEARANCE a Adjusting instrument for valve clearance 4. While the No. 1 cylinder is at the compression top dead center, adjust the valve clearances marked with
More information