Caliber Gauges & Instruments Laboratory, S. No. 14/1, Dattadigamber Soc. B, Warje Jakat Naka, Pune, Maharashtra

Size: px
Start display at page:

Download "Caliber Gauges & Instruments Laboratory, S. No. 14/1, Dattadigamber Soc. B, Warje Jakat Naka, Pune, Maharashtra"

Transcription

1 Last Amended on - Page 1 of 10 I. DIMENSION (Basic Measuring, Gauge etc.) 1. PLAIN PLUG / WIDTH/ DEPTH/ Upto 100 mm 1.9 µm Using Electronic FLUSH PIN GAUGE DIAMETER /WIDTH / DEPTH $ 100 mm to 300 mm 3.8 µm Comparator with Stand / Gauge block Box 2. THREAD MEASURING WIRE/ Upto 6.35 mm 0.6 µm Using Electronic MEASURING PIN $ Upto 20.0 mm 0.8 µm Comparator With Stand Comparison 3. FEELER GAUGE / PAINT THICKNESS FOIL (Thickness) $ Upto 2 mm 3.8 µm Using Digital Outside Micrometer 4. THREAD PLUG (Effective and Major Diameter) 0 to 100 mm 100 mm to 300 mm 3.0 µm 4.0 µm Using Floating Carriage Micrometer Length Measuring 5. TAPER THREAD RING (Effective Dia/Step) 6. TAPER THREAD PLUG ( Effective Diameter/Step ) 0 to 100 mm 4.0 µm Using Length Measuring 0 to 100 mm 4.0 µm Using Floating Carriage Micrometer

2 Last Amended on - Page 2 of SNAP 2 mm to 100 mm 2.1 µm Using Gauge Block 100 mm to 300 mm 5.3 µm 8. THREAD RING (Effective & Minor Diameter 9. THREAD PITCH ( Pitch Length ) 0 to 100 mm 100 mm to 300 mm 2.8 µm 3.8 µm Using Length Measuring 0 to 10 mm 25.0 µm Using Profile Projector 10. RADIUS 0 to 30 mm 47.1 µm Using Profile Projector 11. V- BLOCK $ Symetricity Parallism Squareness Upto 250 mm Upto 250 mm Upto 250 mm 7.5 µm 7.2 µm 7.0 µm Using Mandrel/ Square Cylindrical. / Lever Dial 12. TEST SIEVES APERTURE SIZE 13. CYLINDRICAL SETTING MASTER / O.D MASTER $ mm to 100 mm 24 µm Using Profile Projector 0 to 100 mm 1.0 µm Using Electronic Comparator with Stand/Slip Gauge Box/ Length Bar 14. MICROMETER 0 to 200 mm 2.0 µm Using Electronic SETTING ROD $ 200 mm to 500 mm 5.2 µm Comparator/ 500 mm to 1000 mm 12.0 µm Slip Gauge / Long Slip Gauge

3 Last Amended on - Page 3 of SETTING / PLAIN RING 0 to 100 mm 100 to 300 mm 2.5 µm 3.5 µm Using Length Measuring 16. SLIP 01 mm to 25 mm 0.12 µm Using Gauge Block (Carbide) 25 mm to 75 mm 0.14 µm Calibrator 75 mm to 100 mm 0.18 µm SLIP GAUGE 00 to 25 mm 0.12 µm Using Gauge Block (Steel) 25 mm to 75 mm 0.14 µm Calibrator 75 mm to 100 mm 0.24 µm 17. LENGTH BAR /LONG SLIP 0 to 600 mm 3.0 µm Using Long Gauge Block 18. CALIPER CHECKER $ 0 to 600 mm 4.0 µm Using Long Slip Gauge/ Digital Lever 19. ENGINEERS PARALLEL $ Parallism 0 to 100 mm 2.0 µm Using Electronic Comparator 20. VERNIER CALIPER $ (Digital/Dial/ Plain) L.C.: mm Φ Upto 1000 mm 16 µm Using Length Bar/ Slip L.C.: mm Upto 600 mm 18 µm Gauge 21. VERNIER HEIGHT (Digital/ Dial / Plain) L.C.: mm 0 to 600 mm 6.3 µm Using Caliper Checker / Using Length Bar/ Slip Gauge

4 Last Amended on - Page 4 of VERNIER DEPTH CALIPER $ (Digital/ Dial/ Plain) L.C.: mm Φ 0 to 600 mm 16 µm Using Caliper Checker / Length Bar 23. PLUNGER TYPE DIAL L..C: mm 0 to 25 mm 0.3 µm L.C.:-0.001mm Φ Upto 1 mm 1.4 µm Using Length Measuring Upto 50 mm 2.2 µm & Laser Interferometer 24. LEVER TYPE DIAL L.C.: mm Φ 0 to 2 mm 0.08 µm Using Length Measuring & Laser Interferometer 25. DIAL BORE (Transmission Accuracy) L. C.: mm 0 to 2 mm 3.5 µm Using Length Measuring 26. OUTSIDE MICROMETER $ L.C.: mm 0 to 100 mm 6.0 µm Using Gauge Block / 100 mm to 300 mm 7.4 µm Length Bar 300 mm to 1000 mm 27 µm L.C.: mm 0 to 300 mm 2.8 µm

5 Last Amended on - Page 5 of DEPTH MICROMETER $ L.C.: mm Φ 0 to 300 mm 4.2 µm Using Caliper Checker / Length Bar 28. INTERNAL MICROMETER $ (Micrometer Head) L.C.: mm Φ 5 mm to 100 mm 2.0 µm Using Single Axis Extension Rod 0 to 350 mm 7.95 Measuring SIP/Slip Gauge Three Point Micrometer 0 to 100mm 2.8 Using Plain Ring Gauge 29. DIAL SNAP ( Flatness / Parallism) 2 mm to 200 mm 2.5 µm Using Gauge Block / Optical Flat 30. INTERNAL CALIPER $ L.C. : mm Φ 10 mm to150 mm 6.0 µm Using Length Measuring 31. ULTRASONIC THICKNESS 0 to 200 mm 47.0 µm Using Slip Gauge 32. COATING THICKNESS 0 to 2 mm 7.5 µm Using Paint Thickness Foil 33. GLASS SCALE $ L.C.:-0.01 mm 0 to 10 mm 2.0 µm Using Single Axis L.C.:- 0.1 mm 0 to 300 mm 2.2 µm Measuring

6 Last Amended on - Page 6 of MEASURING SCALE $ L.C.: 1.0 mm Upto 2000 mm 150 L, L is in meter Using Measuring Scale & Tape Calibration System MEASURING TAPE $ L.C.:- 0.5 mm Φ L.C.;- 1.0 mm 0 to 5000 mm 0 to mm 150 L, L is in meter Measuring Scale & Tape 35. DIAL THICKNESS L.C. :-0.001mm Φ 0 to 100 mm 1.2 µm Using Slip Gauge 36. PISTAL CALIPER $ L.C.: mm Φ 0 to 100 mm 71 µm Using Slip Gauge 37. FLOATING CARRIAGE MICROMETER $ L.C.: mm 0 to 100 mm 1.6 µm Using Cylindrical Master / L. C.: mm 0 to 200 mm 2.0 µm Gauge Block/ Mandrel/ Optical Flat 38. DIAL CALIBRATION TESTER $ L.C.: mm Φ 0 to 25 mm 0.8 µm Using Gauge Block / Electronic Probe 39. ELECTRONIC PROBE $ L.C.: mm 0 to 1 mm 0.4 µm Using Slip Gauge L.C.: mm 0 to 25 mm 0.5 µm 40. COMPARATOR STAND $ 100 mm x 100 mm 0.62 µm Using Optical Flat / (Base Flatness) 200 mm x 200 mm 1.20 µm Lever Dial

7 Last Amended on - Page 7 of GAUGE BLOCK COMPARATOR 0 to 100 mm 0.12 µm Using Slip Gauge Set 42. SPIRIT LEVEL (Flat/Vee/Frame) L.C.: mm/m Φ 1 mm/m 10 µm/m Using Electronic Level Meter 43. BEVEL PROTECTOR / DEGREE PROTECTOR INCLINOMETER $ L. C.:- 5 min Φ min Using Angular Slip Sine Bar Gauge Block 44. PLAIN TAPER PLUG 0 to 100 mm 3.0 µm Using Length Measuring (Major/Minor/Diameter. / Angle/ Step) 45. PLAIN TAPER RING (Major/Minor/Diameter. / Angle/ Step) 0 to 100 mm 3.0 µm Using Length Measuring 46. RIGHT ANGLE / ANGLE PLATE $ ( Squarness / Parallism / Flatness ) 0 to 240 mm 7.8 µm Using Cyl. Square Master / Lever dial 47. RIGHT ANGLE/ SQUARE MASTER $ 0 to 600 mm 7.8 µm Using Square Master

8 Last Amended on - Page 8 of STRAIGHT EDGE $ (Straightness) 0 to 2000 mm L 1.7 µm 125 L is in mm Using Electronic level 49. SINE BAR/SINE CENTER $ 0 to 200 mm 0 to µm 7.0 arc sec Using Sine Bar / Electronic Height Gauge 50. SURFACE PLATES $ Upto 1000 x 1000 mm L W 1.8 µm 125 L is in mm Using Electronic Level SURFACE PLATES 200 X 200 to 5000x 5000 mm L W 1.8 µm 125 L is in mm Using Electronic Level 200 X 200 to 5000x 5000 mm L W 6.1 µm 125 L is in mm Using Spirit Level 51. SCALE & TAPE MEASURING MACHINE 0 to 5000 mm ( L) µm L in m Using Laser interferometer 52. GAUGE BLOCK 0 to 100 mm 0.12 µm Using Gauge Block K COMPARATOR Grade 53. BENCH CENTER (Co- axiality) 0 to 300 mm 4.5 µm Using Test mandrel & Lever Dial

9 Last Amended on - Page 9 of 10 II. DIMENSION (Precision s) 1. LENGTH MEASURING 0 to 500 mm ( ) µm MACHINE $ L is in meter LENGTH MEASURING MACHINE (Vertical & Horizontal Axis) L. C.: / mm 0 to mm ( ) µm L is in meter 2. PROFILE PROJECTOR VISION MEASURING MACHINE LINEAR MAGNIFICATION ANGULAR 0 to 300 mm 10 X to 100 X 0 to % 3.0 min arc Using Laser interferometer Using Laser interferometer Using Glass Scale Angular Slip II. PRESSURE INDICATING DEVICES 1. PRESSURE GAUGE (Digital/Analogue) 0 to 10 bar 0 to 350 bar 0.15 bar 1.4 bar Using Digital Pressure by Comparison Method as per DKD R-6-1

10 Last Amended on - Page 10 of VACUUM GAUGE (Digital/Analogue) (-) 0.8 bar to 0 bar 0.62 bar Using Digital Vacuum by Comparison Method as per DKD R-6-1 * Capability is expressed as an uncertainty ( ) at a confidence probability of 95% $ Only in Permanent Laboratory Only for Site Calibration # The laboratory is also capable for site calibration however, the uncertainty at site depends on the prevailing actual environmental conditions and master equipment used. Φ Laboratory can also calibrate instruments/devices of coarser resolution / least count within the accredited range using same reference standard/ master equipment under the scope of accreditation.

Cal-Tech Calibration Services Pvt. Ltd., Flat No.8, Avadhut Heights, Anand Nagar, Sinhgad Road, Pune, Maharashtra

Cal-Tech Calibration Services Pvt. Ltd., Flat No.8, Avadhut Heights, Anand Nagar, Sinhgad Road, Pune, Maharashtra Last Amended on - Page 1 of 5 I. DIMENSION 1. CALIPER $ L.C. :-10 µm 0 to 300 mm 12.0 µm Using Caliper Checker; Gauge 0 to 1000 mm 12.0 µm Block Set L.C. :-20 µm 0 to 600 mm 16.0 µm 0 to 1000 mm 20.0 µm

More information

Accurate Measurements, Plot No.103, D Block, Meethapur Ext., Badarpur, New Delhi. Discipline Mechanical Calibration Issue Date

Accurate Measurements, Plot No.103, D Block, Meethapur Ext., Badarpur, New Delhi. Discipline Mechanical Calibration Issue Date Last Amended on 11.11.2014 Page 1 of 6 I. DIMENSION 1. Dial/ Digital Vernier Caliper $ L.C.: 0.01mm Φ 0 to 200 mm 7.5 µm Using Slip Gauge Set & L.C.: 0.01mm Φ 0 to 300 mm 12.17 µm Using Slip Gauges & Caliper

More information

Q-Tech Engineering Services, S-134, C/o, Precision Engineering Works, MIDC, Bhosari, Pune, Maharashtra

Q-Tech Engineering Services, S-134, C/o, Precision Engineering Works, MIDC, Bhosari, Pune, Maharashtra Last Amended on 24.05.2015 Page 1 of 5 I. DIMENSION 1. EXTERNAL MICROMETER $ L.C. 1 µm Φ >100 mm to 300 mm 1.4 µm 3.0 µm Using Slip Gauge Blocks Gr '0' / Long Slip Gauges, by Comparison 2. DEPTH MICROMETER

More information

Alcalab Private Limited, 3rd Floor, Ashiana Trade Centre, Adityapur, Jamshedpur, Jharkhand. Discipline Mechanical Calibration Issue Date

Alcalab Private Limited, 3rd Floor, Ashiana Trade Centre, Adityapur, Jamshedpur, Jharkhand. Discipline Mechanical Calibration Issue Date Last Amended on - Page 1 of 11 I. DIMENSIONS 1. SLIP 0.5 mm to 25 mm 0.25 μm Using Slip Gauge (K-Grade) & > 25 mm to 50 mm 0.34 μm Double Probe Comparator > 50 mm to 75 mm 0.46 μm > 75 mm to 100 mm 0.58

More information

Discipline Mechanical Calibration Issue Date Certificate Number C-0752 Valid Until Last Amended on - Page 1 of 6

Discipline Mechanical Calibration Issue Date Certificate Number C-0752 Valid Until Last Amended on - Page 1 of 6 Last Amended on - Page 1 of 6 I DIMENSION 1. Caliper $ (Vernier/Dial/Digital) LC : 0.01mm 0 to 600 mm 0 to 1000 mm 12.2 µm 13.3 µm Using Caliper Checker, Slip Gauge Block & 2. Depth Caliper $ (Vernier/Dial/Digital)

More information

Central Mechanical Engineering Research Institute, Mahatma Gandhi Avenue, Durgapur, West Bengal

Central Mechanical Engineering Research Institute, Mahatma Gandhi Avenue, Durgapur, West Bengal Last Amended on 23.09.2014 Page 1 of 9 I. DIMENSION 1. GAUGE BLOCKS $ 0.5 mm to 25 mm 25 mm to 50 mm 50 mm to 75 mm 75 mm to 100 mm 2. LENGTH BAR $ Upto 300 mm 300 mm to 600 mm 300 mm to 1000 mm 0.11µm

More information

QA Tech (A Division of GMP Technical Solutions Pvt. Ltd.), L-73, Verna Industrial Estate, Verna Salcette, Goa

QA Tech (A Division of GMP Technical Solutions Pvt. Ltd.), L-73, Verna Industrial Estate, Verna Salcette, Goa Last Amended on - Page 1 of 5 I. DIMENSION 1. CALIPER $ L.C. :-10µm Φ 0 to 300 mm 13 µm Using Caliper Checker; & T.C. Gauge Block Set by Comparison L.C. :- 20µm 0 to 1000 mm 22 µm Using Caliper Checker;

More information

Discipline Mechanical Calibration Issue Date Certificate Number C-0751 Valid Until Last Amended on

Discipline Mechanical Calibration Issue Date Certificate Number C-0751 Valid Until Last Amended on Last Amended on 10.03.2016 Page 1 of 5 I. DIMENSION 1. Vernier caliper $ 0 to 300 mm/0.01 mm ± 12.0 µm Using Caliper Checker 0 to 300 mm/0.02 mm ± 16.1 µm Using Caliper Checker 0 to 600 mm/0.01 mm ± 14.0

More information

Discipline Mechanical Calibration Issue Date Certificate Number C-0393 Valid Until Last Amended on - Page 1 of 6

Discipline Mechanical Calibration Issue Date Certificate Number C-0393 Valid Until Last Amended on - Page 1 of 6 Last Amended on - Page 1 of 6 I. DIMENSION 1. Vernier Caliper (Digital/ Dial/ Scale) $ L.C.: 0.01 mm 0 to 150 mm 7.7 µm Using Caliper Checker 0 to 200 mm 8.1 µm 0 to 300 mm 9.3 µm 0 to 600 mm 13.9 µm 2.

More information

Autocal Solutions Pvt. Ltd., Plot No. BG-74, Gala No. 1 & 2, Jai Tulja Bhavani Indl. Premises, Telco Road, MIDC Bhosari, Pune, Maharashtra

Autocal Solutions Pvt. Ltd., Plot No. BG-74, Gala No. 1 & 2, Jai Tulja Bhavani Indl. Premises, Telco Road, MIDC Bhosari, Pune, Maharashtra Last Amended on - Page 1 of 5 I. DIMENSION 1. CALIPER (Vernier/Dial/Digital) L. C. : 10µm Φ 0 to 600 mm 16 µm Using Caliper Checker & External Micrometer by 2. DEPTH GAUGE (Vernier/Dial/ Digital) L. C.

More information

Accurate Labs, 311, 312 Govinda Complex, GIDC Char Rasta, Vapi, Valsad, Gujarat. Discipline Mechanical Calibration Issue Date

Accurate Labs, 311, 312 Govinda Complex, GIDC Char Rasta, Vapi, Valsad, Gujarat. Discipline Mechanical Calibration Issue Date Last Amended on - Page 1 of 9 I. DIMENSION 1. CALIPER $ Vernier L.C. 0.01mm 7.5 µm 9.0 µm Using Caliper Checker & Slip Gauges L.C. 0.05mm 29.5 µm 30.0 µm Dial / Electronic L.C. 0.02mm 12.5 µm 13.5 µm 2.

More information

Institute for Design of Electrical Measuring Instruments, Swatantryaveer Tatya Tope Marg, Chunabhatti, Sion, Mumbai, Maharashtra

Institute for Design of Electrical Measuring Instruments, Swatantryaveer Tatya Tope Marg, Chunabhatti, Sion, Mumbai, Maharashtra Last Amended on 02.09.2014 Page 1 of 10 I. DIMENSION 1 Calipers $ Up to 600 mm 10.4 µm Using Caliper Checker by Up to 1000 mm 13.2 µm Using Long Slip Gauge by 2 Height Gauges $ Up to 600 mm 12.8 µm Using

More information

A.A. Calibration Pvt. Ltd., 13-C/18, Vasundhara Haat, Vasundhara, Ghaziabad, Uttar Pradesh. Discipline Mechanical Calibration Issue Date

A.A. Calibration Pvt. Ltd., 13-C/18, Vasundhara Haat, Vasundhara, Ghaziabad, Uttar Pradesh. Discipline Mechanical Calibration Issue Date Last Amended on 02.09.2014 Page 1 of 10 I. DIMENSION 1. VERNIER CALIPER $ L.C. 0.01mm 0 to 300 mm 0 to 600 mm 0 to 1000 mm 8 µm 14 µm 16 µm, Slip Gauge Accessories, Gauge Block L.C. 0.02 mm 0 to 1500 mm

More information

Hi-Tech Calibration, 307, 3rd Floor, Govinda Complex, Char Rasta, Vapi, Gujarat. Discipline Mechanical Calibration Issue Date

Hi-Tech Calibration, 307, 3rd Floor, Govinda Complex, Char Rasta, Vapi, Gujarat. Discipline Mechanical Calibration Issue Date Last Amended on 18.01.2016 Page 1 of 7 I. DIMENSIONS 1. CALIPER $ (Vernier, Dial, Electronics) L.C.0.01 mm up to 1000mm 24 µm Using Caliper Checker / L.C.0.02 mm up to 600mm 19 µm Length Bars /Slip Gauges

More information

ICL Calibration And Testing Services, SCO - 37, Ground Floor, Sector-12, Panchkula, Haryana. Discipline Mechanical Calibration Issue Date

ICL Calibration And Testing Services, SCO - 37, Ground Floor, Sector-12, Panchkula, Haryana. Discipline Mechanical Calibration Issue Date Last Amended on 09.12.2016 Page 1 of 8 I. DIMENSION (Basic Measuring, Gauge etc.) 1 LENGTH GAUGE/SETTING ROD $ Up to 100 mm >100 mm to 500 mm 1.5 µm 7.20 µm Using ULM, Gauge Block grade- 0 & Electronic

More information

Calitron Calibration Laboratory, U1: 207, Kohinoor Arcade, Tilak Chowk, Nigdi, Pune, Maharashtra

Calitron Calibration Laboratory, U1: 207, Kohinoor Arcade, Tilak Chowk, Nigdi, Pune, Maharashtra Last Amended on 12.09.2014 Page 1 of 7 I. MASS 1. Weights $ (Conventional Mass) 1 mg 0.015 mg Using Weights of 2 mg 0.015 mg accuracy Class F1 and 5 mg 0.015 mg 10 mg 0.015 mg 20 mg 0.020 mg 50 mg 0.020

More information

Discipline Mechanical Calibration Issue Date Certificate Number C-0208 Valid Until Last Amended on

Discipline Mechanical Calibration Issue Date Certificate Number C-0208 Valid Until Last Amended on Last Amended on 12.08.2016 Page 1 of 7 I. DIMENSION (Basic Measuring, Gauge etc.) 1. CALIPER $ (Vernier / Dial / Digital) L.C.: 10 µm ф L.C.: 50 µm ф Upto 600mm 13 m Using Gauge Block Set Grade 0 (Carbide);

More information

Metrology Laboratory, CMTI, Central Manufacturing Technology Institute, Tumkur Road, Bangalore, Karnataka Accreditation Standard ISO/IEC 17025: 2005

Metrology Laboratory, CMTI, Central Manufacturing Technology Institute, Tumkur Road, Bangalore, Karnataka Accreditation Standard ISO/IEC 17025: 2005 aboratory Metrology aboratory, CMTI, Central Manufacturing Technology ast Amended on 22.09.2016 Page 1 of 15 I. DIMENSION (Basic Measuring, Gauge etc.,) 1. ANGE GAUGE BOCKS $ 0 to 90 2.8 arc sec Using

More information

CERTIFICATE OF ACCREDITATION

CERTIFICATE OF ACCREDITATION CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that SP Metrology System Thailand Co., LTD 88/115

More information

Price List. Calibration Fee

Price List. Calibration Fee 3/4-5 Moo 3, Klong 5, Klong Luang, Pathumthani, 110, Thailand Tel. +66 577 5100 (Please contact : Customer Service Section Ext. 3101, 310) Fax. +66 577 3659 E-mail : cs@nimt.or.th Website : http://www.nimt.or.th

More information

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Schedule of ccreditation United Kingdom ccreditation Service ccredited to Division of Cromwell Tools Ltd Services Block 65 Chartwell Drive Wigston Leicester LE18 2FS Contact: Mr T still Tel: +44 (0)116-2572396

More information

Rev /07/2015 CATALOGUE - CALIBRATION SERVICES 1

Rev /07/2015 CATALOGUE - CALIBRATION SERVICES 1 Rev. 02 07/07/2015 CATALOGUE - CALIBRATION SERVICES 1 OVER 100 ITEMS We are proud to present to you our new catalogue for 2015. In the following pages we present more than 100 instrument types, which we

More information

Height Master Page 345. Check Master Page 349. Calibration Tools Page 354

Height Master Page 345. Check Master Page 349. Calibration Tools Page 354 Calibration Instruments Height Master Page 345 Check Master Page 349 Calibration Tools Page 354 344 Digital Height Master Functions ZERO/ABS DATA/HOLD Auto Power OFF after 20 min. non use Low voltage alarm

More information

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Schedule of ccreditation United Kingdom ccreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK ccredited to Laboratory locations: Unit 9 G B Quality ssurance (Consultants)

More information

Shriram Institute For Industrial Research, 14-15, Sadarmangala Industrial Area, Whitefield Road, Bangalore, Karnataka

Shriram Institute For Industrial Research, 14-15, Sadarmangala Industrial Area, Whitefield Road, Bangalore, Karnataka Certificate Number CC-2083 (in lieu of C-0216, C-0304, C-1497) Page 1 of 7 ELECTRO-TECHNICAL CALIBRATION I. MEASURE 1. Time $ 5 sec to 9900 sec 0.12 sec to 5.8 sec Using Digital Time Totalizer (Digital

More information

Page : 1 of 16. FIELD OF TESTING : Calibration and Measurement CALIBRATION & MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINITY *

Page : 1 of 16. FIELD OF TESTING : Calibration and Measurement CALIBRATION & MEASUREMENT CAPABILITY EXPRESSED AS AN UNCERTAINITY * Metrix Precision Pte Ltd Certificate No. : LA-2014-0581-C No. 23 Tagore Lane #02-03/04 Tagore 23 Warehouse Issue No. : 2 Singapore 787601 Date : 29 July 2016 FIELD OF TESTING : Calibration and Measurement

More information

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Schedule of ccreditation United Kingdom ccreditation Service Issue No: 028 Issue date: 10 pril 2018 ccredited to 6 Banner Park Wickmans Drive Coventry CV4 9X Contact: Keith rnold Tel: +44 (0)2476 426 316/317

More information

Gear Measurement. Lecture (7) Mechanical Measurements

Gear Measurement. Lecture (7) Mechanical Measurements 18 3. Gear profile checking 2. Involute measuring machine In this method the gear is held on a mandrel and circular disc of same diameter as the base circle of gear for the measurement is fixed on the

More information

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 Unit 3 24-26 Boulton Road Stevenage Hertfordshire SG1 4QX ontact: Mr G J Wilson Tel: +44 (0) 1438 900080 Fax: +44 (0) 1438

More information

Schedule. 300 mm to 600 mm 600 mm to 1000 mm inch to 12 inch

Schedule. 300 mm to 600 mm 600 mm to 1000 mm inch to 12 inch LABORATORY LOCATION: (PERMANENT LABORATORY) MITUTOYO (M) SDN. BHD. MAH SING INTEGRATED INDUSTRIAL PARK BANDAR PINGGIRAN SUBANG 4, JALAN UTARID U5/14, SECTION U5 40150 SHAH ALAM SELANGOR, MALAYSIA Page:

More information

Schedule. 200 C to 400 C. 400 C to 660 C C to 800 C C to 1300 C C to 1200 C. 0 C to 1700 C. 0 C to 1700 C.

Schedule. 200 C to 400 C. 400 C to 660 C C to 800 C C to 1300 C C to 1200 C. 0 C to 1700 C. 0 C to 1700 C. Page: 1 of 9 LABORATORY LOCATION: (PERMANENT LABORATORY) PPCALIBRATION SERVICES SDN. BHD. NO. 15, MEDAN BUKIT EMAS PUSAT PERNIAGAAN BUKIT EMAS 14000 BUKIT MERTAJAM, PULAU PINANG MALAYSIA This laboratory

More information

Measuring. Affordable. Effective. Instruments

Measuring. Affordable. Effective. Instruments Measuring Effective Affordable Instruments 2 Electronic Calipers 00534002 00534003 00534020 n Stainless steel frame n Thumb wheel for rapid setting n Direct Metric/Inch conversion n Accuracy to 0,02 mm

More information

TRI-STATE INSTRUMENT SVC, INC

TRI-STATE INSTRUMENT SVC, INC CALIBRATION RATE POLICY AND PRICING 2017 Typically, compliance with ISO-900x and TS 16949 specifications require LONG FORM calibration reports in the following formats. Format #1 -- Before Adjustment or

More information

Standard Scales SERIES 182 Made of Low-Expansion Glass. Working Standard Scales SERIES 182 E-32

Standard Scales SERIES 182 Made of Low-Expansion Glass. Working Standard Scales SERIES 182 E-32 Standard Scales SERIES 182 Made of Low-Expansion Glass High-precision glass scales manufactured under Mitutoyo s leading-edge Linear Scale production technology. High accuracy is guaranteed to be used

More information

CALIBRATION SYSTEM CERTIFICATE

CALIBRATION SYSTEM CERTIFICATE CALIBRATION SYSTEM CERTIFICATE With respect to products (measuring instruments and testing instruments), we hereby certify that we have established our calibration system traceable to the national (international)

More information

Welcome to Garber C O R P O R AT E O V E R V I E W

Welcome to Garber C O R P O R AT E O V E R V I E W CORPORATE OVERVIEW Garber Metrology is one of the only companies in the Mid-Atlantic Region that combines full service weighing solutions, a wide range of calibration /metrology services and a broad scope

More information

This annex is valid from: to Replaces annex dated: Location(s) where activities are performed under accreditation

This annex is valid from: to Replaces annex dated: Location(s) where activities are performed under accreditation Chamber Commerce: 06073326 Location(s) where activities are performed under accreditation ad Office Smaragdstraat 7 7554 TD ngelo OV The Netherlands Location Abbreviation/ location Smaragdstraat 7 7554

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 RIVERVIEW CALIBRATION SERVICES, LTD 5706 Veto Road Belpre, OH 45714 J. Michael Pennell Phone: 740 678 8625 CALIBRATION Valid To: July

More information

TEST AND CALIBRATION SERVICES Ensuring quality and reliability.

TEST AND CALIBRATION SERVICES Ensuring quality and reliability. > TEST AND CALIBRATION SERVICES Ensuring quality and reliability www.thalesgroup.com.au TEST AND CALIBRATION SERVICES ENSURING QUALITY AND RELIABILITY Introduction Thales Australia s Test and Calibration

More information

Gauge Blocks - Reference for Precision

Gauge Blocks - Reference for Precision ß Measuring and Laying-Out Tools, Testing Instruments Gauge Blocks - Reference for Precision Parallel gauge blocks in compliance with DIN EN ISO 650 are supplied in the following calibration and tolerance

More information

SCOPE OF ACCREDITATION TO ISO/IEC & KS Q ISO/IEC

SCOPE OF ACCREDITATION TO ISO/IEC & KS Q ISO/IEC SCOPE OF ACCREDITATION TO ISO/IEC 17025-2005 & KS Q ISO/IEC 17025-2006 Korea Instrument Co., Ltd. Branch 45, Gwangjang-ro 56beon-gil, Sasang-gu, Busan 46976 Phone : 051-322-0880, Fax : 051-322-4066, E-mail

More information

SAMPLES GAUGES. Tolerances OUR SPECIAL OFFER: PLUG GAUGES WITH REQUIRED FIT OR INDIVIDUAL TOLERANCES ACCORDING TO YOUR SPECIFICATIONS

SAMPLES GAUGES. Tolerances OUR SPECIAL OFFER: PLUG GAUGES WITH REQUIRED FIT OR INDIVIDUAL TOLERANCES ACCORDING TO YOUR SPECIFICATIONS SAMPLES GAUGES PLUG GAUGES Tolerances GO side Fit NO GO side OUR SPECIAL OFFER: PLUG GAUGES WITH REQUIRED FIT OR INDIVIDUAL TOLERANCES ACCORDING TO YOUR SPECIFICATIONS BESTSELLER: FEELER GAUGE TAPES IN

More information

Small Tool Instruments and Data Management

Small Tool Instruments and Data Management Small Tool Instruments and Data Management Dial Gauge Stands Pages 268 272 Comparator Stands Pages 273 274 Joint Magnetic Stands Concentricity testers Pages 275 280 Angulometers, steel squares Pages 281

More information

Department of Mechanical Engineering ME6513 - METROLOGY AND MEASUREMENT LAB LABORATORY MANUAL Name Register No. Branch Year & Semester : : : : 1 CONTENTS S.NO. DATE EXPERIMENT NAME PAGE NO. 1 Calibration

More information

CALIBRATION PRICE LIST

CALIBRATION PRICE LIST THREADED API STANDOFF SIZE SPEC 5 LINE PIPE $95 ea $150 ea 1/8 4 working 5 12 working $180 ea $290 ea $190 set 1/8 12 masters TUBING (UPTBG & TBG) (EUE & NUE) (1.0500 4 ½ ) $125 ea $190 set Working Masters

More information

Small Tool Instruments and Data Management

Small Tool Instruments and Data Management Small Tool Instruments and Data Management Gauge Blocks Pages 302 311 Calibration instruments Pages 312 319 301 Basic information on gauge blocks Characteristics of Mitutoyo gauge blocks: Mitutoyo, at

More information

+91-8048600379 Rampura Tools http://www.rampuratools.in/ We are one of the leading distributor, suppliers and traders of Measuring Instrument. Owing to their accurate measurement, sturdy construction,

More information

CERTIFICATE OF ACCREDITATION

CERTIFICATE OF ACCREDITATION CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Garber Metrology Weighing Solutions & Precision

More information

Page 1 of 5. United Testing Systems, Inc S. Acacia Avenue Fullerton, CA William Warner, Quality Manager

Page 1 of 5. United Testing Systems, Inc S. Acacia Avenue Fullerton, CA William Warner, Quality Manager IAS Accreditation Number Accredited Entity Address CL-128 1375 S. Acacia Avenue Fullerton, CA 92831 William Warner, Quality Manager Contact Name Telephone +1 (714) 638-2322 Effective Date of Scope July

More information

+91-8048718949 Bearing & Tools Centre http://www.measuringtestinginstrument.com/ We are a renowned dealer and supplier of a wide assortment of precision engineered testing and measuring equipment. Our

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 ALDINGER COMPANY 1440 Prudential Drive Dallas, TX 75235 Timothy R. Detten Phone: 214 638 1808 CALIBRATION Valid To: July 31, 2018 Certificate

More information

Measurement & Calibration

Measurement & Calibration Measurement & Calibration MIC TRAC 4000 In-House Precision Gage Calibration System Inspect Parts, Calibrate, and Track Gages Step 1: Find what type of gages you have. Gages & Indicators for Calibration

More information

Service INFO Calibration. Tool repair service of thread gauges. Calibration

Service INFO Calibration. Tool repair service of thread gauges. Calibration Service Tool repair service -2 Calibration of thread gauges -16 Regrinding service -5 Calibration of plain gauges -17 Coating service -8 Calibration of appliances -19 INFO ISO 90 ff test equipment monitoring

More information

IEC SYSTEM FOR CONFORMITY TESTING AND COMMITTEE OF TESTING LABORATORIES CERTIFICATION OF ELECTRICAL EQUIPMENT

IEC SYSTEM FOR CONFORMITY TESTING AND COMMITTEE OF TESTING LABORATORIES CERTIFICATION OF ELECTRICAL EQUIPMENT IEC SYSTEM FO CONFOMITY TESTING AND CETIFICATION OF ELECTICAL EQUIPMENT COMMITTEE OF TESTING LABOATOIES =equired by Lab S=May be subcontracted TESTING AND MEASUING EQUIPMENT/ALLOWED SUBCONTACTING Power

More information

Lecture (7) on. Gear Measurement. By Dr. Emad M. Saad. Industrial Engineering Dept. Faculty of Engineering. Fayoum University.

Lecture (7) on. Gear Measurement. By Dr. Emad M. Saad. Industrial Engineering Dept. Faculty of Engineering. Fayoum University. 1 Lecture (7) on Gear Measurement Fayoum University By Dr. Emad M. Saad Industrial Engineering Dept. Faculty of Engineering Fayoum University Faculty of Engineering Industrial Engineering Dept. 2015-2016

More information

Verifying the accuracy of involute gear measuring machines R.C. Frazer and J. Hu Design Unit, Stephenson Building, University ofnewcastle upon Tyne,

Verifying the accuracy of involute gear measuring machines R.C. Frazer and J. Hu Design Unit, Stephenson Building, University ofnewcastle upon Tyne, Verifying the accuracy of involute gear measuring machines R.C. Frazer and J. Hu Design Unit, Stephenson Building, University ofnewcastle upon Tyne, Abstract This paper describes the most common methods

More information

PROMPT ENGINEERING P.O. BOX BARWA VILLAGE, WAKRA, BUILDING NO. 6 SHOP NO. 19 AND 20 DOHA QATAR

PROMPT ENGINEERING P.O. BOX BARWA VILLAGE, WAKRA, BUILDING NO. 6 SHOP NO. 19 AND 20 DOHA QATAR This is to attest that PROMPT ENGINEERING P.O. BOX 24067 BARWA VILLAGE, WAKRA, BUILDING NO. 6 SHOP NO. 19 AND 20 DOHA QATAR Calibration Laboratory CL-165 has met the requirements of AC204, IAS Accreditation

More information

最終校 NEW! STANDARD TOOL RUN-OUT GAUGE SYSTEM. Made in Japan. Concentricity measurement by mounting your current indicator to this system.

最終校 NEW! STANDARD TOOL RUN-OUT GAUGE SYSTEM. Made in Japan. Concentricity measurement by mounting your current indicator to this system. 236p 236p 236p 238p 238p 239p 239p 239p 240p 240p 240p 241p 241p 241p 242p 242p 243p 243p 244p 244p 245p 245p 246p 246p 246p 246p 247p 247p 248p 248p 248p 248p 249p 249p 250p 251p 252p 252p 253p V S 253p

More information

ACCREDITATION FACILITY AUDIT CHECKLIST

ACCREDITATION FACILITY AUDIT CHECKLIST ACCREDITATION FACILITY AUDIT CHECKLIST Institution Name: Date: Designated Trade: Marine and Outdoor Power Equipment Technician AC #: Contact: Location: Course Duration: of weeks: of hours total: of hours

More information

LIGHTWEIGHT ADJUSTABLE SHALLOW DIAMETER GAGES

LIGHTWEIGHT ADJUSTABLE SHALLOW DIAMETER GAGES SERIES 77 For use at machine or inspection area for checking inside and outside diameters, shallow bores, counter bores, pitch diameters of gears, and many other dimensions. LIGHTWEIGHT ADJUSTABLE SHALLOW

More information

Keysight Technologies 5530 Dynamic Calibrator. Data Sheet

Keysight Technologies 5530 Dynamic Calibrator. Data Sheet Keysight Technologies 5530 Dynamic Calibrator Data Sheet Introduction 5530 Dynamic Calibrator Requirements Power Requirements Laser Head: 100 240 Vac, 50/60 Hz 50W (during warmup), 33W (after warmup) Calibrator

More information

0268 Gear tooth calipers

0268 Gear tooth calipers 0268 Gear tooth calipers Stainless steel Factory standard Locking screw Fine adjustment 1 Hardened jaw tips Carbide tipped jaw tips Module Reading Ref. No. List price mm mm 1-26 0.02 0268 201 285.00 1-26

More information

ADRT Series Rotary Stages

ADRT Series Rotary Stages ADRT Series Mechanical-Bearing Rotary Stage High torque output, direct-drive brushless servomotor Cog-free design for outstanding velocity stability Outstanding wobble and runout Direct coupled, high-accuracy

More information

TESA Clearance Sale TESA CAL IP67 DIGITAL CALIPERS (METRIC ONLY) DIGITAL LIGHT CALIPERS DIGITAL DEPTH LIGHT CALIPERS ETALON DIAL CALIPERS

TESA Clearance Sale TESA CAL IP67 DIGITAL CALIPERS (METRIC ONLY) DIGITAL LIGHT CALIPERS DIGITAL DEPTH LIGHT CALIPERS ETALON DIAL CALIPERS CLEARANCE SALE TESA Sale Validité: 31.10.2016 ou épuisement des stocks Gültig bis 31.10.2016 oder solange der Vorrat reicht Validity: 31.10.2016 or while stock lasts TESA CAL IP67 DIGITAL CALIPERS (METRIC

More information

0280 / 0281 Vernier depth gauges

0280 / 0281 Vernier depth gauges 0280 / 0281 Vernier depth gauges Reading parts have a satin chrome finish 862 Low-set master scale Measuring rod with interchangeable pin High-precision laser graduation on the vernier and scale Cardboard

More information

UNDERSTANDING CMM SPECIFICATIONS AND CALIBRATION METHODS

UNDERSTANDING CMM SPECIFICATIONS AND CALIBRATION METHODS UNDERSTANDING CMM SPECIFICATIONS AND CALIBRATION METHODS EDUCATION A TECHNICAL PRESENTATION FROM THE LEADING MANUFACTURER OF METROLOGY INSTRUMENTS Bulletin No. 2183 EDU-14003A-H Mitutoyo Institute of Metrology

More information

Straightness, Angle and Inclination Measurement

Straightness, Angle and Inclination Measurement Straightness, Angle and Inclination Measurement Straightness, Angle and Inclination Measurement H-1 Straightness, Angle and Inclination Measurement Levels with Natural Measuring Base Mechanical instruments

More information

New. Swiss Promo. Shop Proof Technology. TESA-HITE Magna 400 and TESA-Cal. Validity : All prices with VAT excluded

New. Swiss Promo. Shop Proof Technology. TESA-HITE Magna 400 and TESA-Cal. Validity : All prices with VAT excluded Validity : 31.07.2007 All prices with VAT excluded Swiss Promo TESA-HITE Magna 400 and 700 2 Shop-Proof Technology protected against water oil dust New Shop Proof Technology TESA-Cal IP67 6 1730 2190 108

More information

Catalog # Meeting Your Metrology Needs. A.A. Jansson, Inc. Precision Measuring Service and Equipment

Catalog # Meeting Your Metrology Needs. A.A. Jansson, Inc. Precision Measuring Service and Equipment Catalog #10046 2017 Meeting Your Metrology Needs A.A. Jansson, Inc. Precision Measuring Service and Equipment Our Place in History C.E. Johansson, Father of Measurement, of Eskilstuna, Sweden, devoted

More information

ALAR Series Direct Drive, Large-Aperture, Rotary Stage

ALAR Series Direct Drive, Large-Aperture, Rotary Stage ALAR Series Direct Drive, Large-Aperture, Rotary Stage 5 different aperture sizes: 100 mm, 150 mm, 200 mm, 250 mm, 325 mm Continuous or limited travel Axial load capacity up to 595 kg Rotary Stages ALAR

More information

GOVERNMENT ITI DHANUVACHAPURA

GOVERNMENT ITI DHANUVACHAPURA Public Disclosure Authorized Public Disclosure Authorized Public Disclosure Authorized Public Disclosure Authorized HEAVY MACHINERY 1 Milling machine (vertical)size no1 with standard accessories & the

More information

Scope of Accreditation For Global Instrumentation Services, LLC 523 N. Sam Houston Parkway E, Suite 230 Houston, TX Gavin Lewis

Scope of Accreditation For Global Instrumentation Services, LLC 523 N. Sam Houston Parkway E, Suite 230 Houston, TX Gavin Lewis Scope of Accreditation For Global Instrumentation Services, LLC 523 N. Sam Houston Parkway E, Suite 230 Houston, TX 77060 Gavin Lewis 832-428-2737 In recognition of a successful assessment to ISO/IEC 17025:2005

More information

Ref:CL/Mech./ Cal /BID-01(13-14) Date: 10 July 2013

Ref:CL/Mech./ Cal /BID-01(13-14) Date: 10 July 2013 Ref:CL/Mech./ Cal /BID-0(3-4) Date: 0 July 203 SUBJECT: Procurement of Calibration Services for the Equipments in Central Laboratory (Mechanical). Dear Sirs, Technical & Commercial Bids are invited for

More information

Rotary Positioning Stages Introduction

Rotary Positioning Stages Introduction Introduction Features Aluminum/steel construction Protective black anodize finish Low-friction rotary adjustment Precise/accurate movement Trouble-free operation aedal precision rotary stages are utilized

More information

200 m IP67. Partner for specialist retailers. Precision Offers. In Germany at home in demand worldwide. valid until

200 m IP67. Partner for specialist retailers. Precision Offers. In Germany at home in demand worldwide. valid until 3 1 4. 9 4 5 20.- L E st! A S s la n O tock w hile s 200 m m IP67 Partner for specialist retailers Precision Offers In Germany at home in demand worldwide valid until 31.08.2016 1 CALIPERS Pocket vernier

More information

Ultra Series: Crossed Roller Ultra Precision Stages

Ultra Series: Crossed Roller Ultra Precision Stages Ultra Series: Crossed Roller Ultra Precision Stages Bayside Motion Group, has developed Ultra Positioning Stages for applications requiring the ultimate in accuracy. Available with a linear motor, ball

More information

Certificate of Accreditation

Certificate of Accreditation PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares

More information

COMPAC Dial Test Indicators

COMPAC Dial Test Indicators DIN 2270 and factory standard Rotating dial COMPAC Dial Test Indicators Essential for the workshop, but also in the inspection room or measuring laboratory Ideal for comparative measurement on a surface

More information

105000BT & BT/CT Series

105000BT & BT/CT Series 15BT & 16BT/CT Series Ball Bearing and Cross Roller Bearing Tables Designed for high accuracy and extremely smooth motion, 1 series tables are ideal for light to moderate duty cycle applications such as

More information

STANDARD RETOOLABLE GAUGES. Countersink Depth. ID Measuring. Measuring. Wired with integral cycle button. Wireless

STANDARD RETOOLABLE GAUGES. Countersink Depth. ID Measuring. Measuring. Wired with integral cycle button. Wireless STANDARD RETOOLABLE GAUGES ID Measuring Countersink Depth Measuring Wireless Wired with integral cycle button ID Measuring All retoolable by replacing the nosepiece All retoolable by replacing the either

More information

More Detail about Helical & Bevel Helical Reduction Gear Boxes.

More Detail about Helical & Bevel Helical Reduction Gear Boxes. More Detail about Helical & Bevel Helical Reduction Gear Boxes. For Inspection & Checking of these Housings we have Brown & Sharpe (USA) CNC CMM with full automatic rotating Renishaw Probe Head with Inspection

More information

testing and measuring instruments for vehicle wheels

testing and measuring instruments for vehicle wheels testing and measuring instruments for vehicle wheels en testing and measuring instruments for vehicle wheels For more than 20 years MAKRA has been manufacturing measuring and testing equipment for the

More information

Small Tool Instruments and Data Management

Small Tool Instruments and Data Management Small Tool Instruments and Data Management Digital Micrometers Pages 28 34 Analogue Micrometers Pages 35 42 Special Version Micrometers Pages 43 63 External screw type micrometers accessories Pages 65

More information

... CALIBRATION SERVICES PRICELIST. M&B Calibr. Accredited calibration company. No according to ČSN EN ISO/IEC

... CALIBRATION SERVICES PRICELIST. M&B Calibr.   Accredited calibration company. No according to ČSN EN ISO/IEC M&B Calibr... CALIBRATION SERVICES PRICELIST Accredited calibration company No. 2301 according to ČSN EN ISO/IEC 17025. Experience since 1991 Guaranteed quality Professional attitude www.mbcalibr.cz You

More information

ROUGHSCAN SURFACE ROUGHNESS TESTER OPERATIONAL MANUAL

ROUGHSCAN SURFACE ROUGHNESS TESTER OPERATIONAL MANUAL SURFACE ROUGHNESS TESTER OPERATIONAL MANUAL Bms Bulut Makina Sanayi Ve Ticaret Ltd. Şti. İkitelli Organize Sanayi Bölgesi Dolapdere Sanayi Sitesi Ada 4 No : 7-9 İkitelli / İSTANBUL-TÜRKİYE Phone : +90

More information

Measuring tools. Accuracy in measurement. Test-safe use. Multiple versions. Torque wrenches. Vernier calipers Spirit levels Mason s profiles

Measuring tools. Accuracy in measurement. Test-safe use. Multiple versions. Torque wrenches. Vernier calipers Spirit levels Mason s profiles Measuring tools Torque wrenches Vernier calipers Spirit levels Mason s profiles Try squares Feeler gauges Other measuring tools Measuring tapes Accuracy in measurement Measuring tapes, torque wrenches

More information

HexGen HEX HL Hexapod Six-DOF Positioning System

HexGen HEX HL Hexapod Six-DOF Positioning System HexGen HE500-350HL Hexapods and Robotics HexGen HE500-350HL Hexapod Six-DOF Positioning System Six degree-of-freedom positioning with linear travels to 110 mm and angular travels to 40 Precision design

More information

ATX165SL/SLE Series Mechanical-Bearing, Screw-Driven Linear Stage

ATX165SL/SLE Series Mechanical-Bearing, Screw-Driven Linear Stage ATX165SL/SLE Series Mechanical-Bearing, Screw-Driven Linear Stage Travel lengths up to 250 mm with anti-creep crossed-roller bearings Optional center-mounted linear encoder for direct position feedback

More information

Berufsweltmeisterschaft Calgary - Canada 1. Sep- 6. Sep 2009

Berufsweltmeisterschaft Calgary - Canada 1. Sep- 6. Sep 2009 Page 1 of 14 WorldSkills Competition Berufsweltmeisterschaft 1. Sep- 6. 07 INFRASTRUCTURE CNC LIST Milling Concours Mondial des Metiers CNC Fraisage CNC Fräsen Position: Contact: Details: Email: Phone:

More information

Dial and Electronic. Indicators Gauges

Dial and Electronic. Indicators Gauges Dial and Electronic Indicators Gauges 37 AGD Group 2 2900 Electronic Indicators Innovative, Full Featured & Tough 2900 Electronic Indicators are available in a choice of configurations to meet a range

More information

THONBURILOHA ENGINEERING COMPANY PROFILE

THONBURILOHA ENGINEERING COMPANY PROFILE THONBURILOHA ENGINEERING COMPANY PROFILE ก 19. 30 ก ก ก. 10140. 02-4271471, 02-4275625, 02-4277757 FAX. 02-4277820 ก / ก ก ก. ก ก ก ก ก 42 ก ก ก ก ก ก ก 4 8 ก 20 ก ก ก ก ก ก Managing Director ก THONBURILOHA

More information

TESA IMICRO capa µ system with Digital Display

TESA IMICRO capa µ system with Digital Display DIN 86 T4 (Style C1) 0,001 0.0005 in TESA IMICRO capa µ system with Digital Display A successful combination of the TESA patented capacitive measuring system with the IMICRO unique cone. Metric/inch Conversion

More information

Universal Thread Measuring Machine

Universal Thread Measuring Machine Universal Thread Measuring Machine Chotest Technology Inc. Office Add: 2/F, Building B1, Zhiyuan, Xueyuan Road, Xili, Nanshan, Shenzhen, China Factory Add: 1/F, Building No.7, HKC Industry Park, Shiyan,

More information

Dial Test Indicators SERIES 513

Dial Test Indicators SERIES 513 Dial Test s SERIES 513 Description of Icon Icon Description With revolution counter Long contact point Jeweled bearing Double scale spacing, easy to read Compact Dustproof Anti-magnetic FEATURES Narrow

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT

More information

Check Points. for Measuring Instruments

Check Points. for Measuring Instruments Check Points for Measuring Instruments Introduction Measurement the word can mean many things. In the case of length measurement, there are many kinds of measuring instruments and their corresponding measuring

More information

Certificate of Accreditation

Certificate of Accreditation PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Torreón, Coahuila, México C.P. 27019 (Hereinafter

More information

PRO165SL/SLE Series. Mechanical Bearing, Ball-Screw Stage. Improved second-generation design. High-performance in a cost-effective package

PRO165SL/SLE Series. Mechanical Bearing, Ball-Screw Stage. Improved second-generation design. High-performance in a cost-effective package PRO165SL/SLE Series Mechanical Bearing, Ball-Screw Stage Improved second-generation design High-performance in a cost-effective package Rugged mechanical construction Optional linear encoder 18 models

More information

SHAFT ALIGNMENT FORWARD

SHAFT ALIGNMENT FORWARD Service Application Manual SAM Chapter 630-76 Section 24 SHAFT ALIGNMENT FORWARD One of the basic problems of any installation is aligning couplings or shafts. Therefore, this section will endeavor to

More information

ISO/IEC ACCREDITED CALIBRATION LABORATORY

ISO/IEC ACCREDITED CALIBRATION LABORATORY My history with Indicator Calibrators Cornerstone Metrology Service Inc. was established in 1983 and our first indicator calibrator was made by Federal. It has a 0-1 standard mic head with a approx. 4

More information