Asphalt Distributors, Levelers, Mixers, Crack Sealing Equip., etc. (See for Tools)

Transcription

1 144 Asphalt Distributors, Levelers, Mixers, Crack Sealing Equip., etc. (See for Tools) PATCH TRUCK Part # ITEM DESCRIPTION Quantity Price Each Price Extended TCM 42580DHE Patcher model TCM 42580DHETRUCK A unitized asphalt repair TRUCK capable of making permanent asphalt repairs under most weather conditions. BODY DIMENSIONS The body is 112 long, 50 high and 78 wide. It has Diamond Tread safety step side fenders with two ladders, body assist handles. Body has L.E.D. style stop, turn, emergency flashers and marker lights. The body has a lockable tool storage compartment measuring 83 long, 18 deep and 10 high. MUD FLAPS INCLUDED. BODY INSULATION The asphalt aggregate hopper and road oil tank are fully insulated with 2 industrial, high temperature 12R factor insulation encased in a double steel jacket. Optional: Hydraulic Operated Steel Top Doors OR Optional 2 Insulated Tarp with tie downs. restriction indicator: CAPACITY The asphalt aggregate hopper holds 4.25 cubic yards level full or 6 tons maximum load. HEATING SYSTEMS The body shall have a dry radiant heat chamber heated by 2 each 150,000 BTU retort tube propane burners with vertical exhaust stacks. The exhaust stack dampeners are electronically actuated to close when burners are off to reduce heat loss. The burners are thermostat controlled and regulated at 10 PSI. The ignition system is 12 volt DC with electronic igniter. Gas burner has a safety shutoff on loss of flame or excessive temperature. Automatic safety shutoff when diesel pump is operating. Burner has two stages, ignites on 10 oz. pressure, operates at 10 PSI, on high burn regulated by the same thermostat as the electric heater. Thermostats will be 0/300 F. solid state. ELECTRONIC CONTROLS All electronic controls will be solid state shock resistant. Thermostat for tack oil tank is 50/200 F. Thermostat for asphalt aggregate hopper is 0/300 F. Thermostat for the asphalt hopper has built in high limit safety shut down switch. Same thermostat controls the 12 volt LP Gas fired system and the 220 volt electric heating system. EMULSION OIL TANK CAPACITY AND HEATING SYSTEM The tank, built onto the main body, has a capacity of 80 gallons and a double steel jacket with 2 insulation. The tank is equipped with a heat transfer system with an adjustable temperature valve that is capable of heating the emulsion oil from 0 to 150 F., using the truck engine coolant system as the heat source. The emulsion pump and all lines are in an insulated heated area. The tank has 220 volt thermostat controlled NEMA explosion proof dry well electric heater and a hot well for storing the spray wand in cold weather. Tank has an 8 fill spout and a 2 gate valve on tank drain. For ease of maintenance or change out of heater, tank does not have to be drained. ELECTRIC HEATING SYSTEM The asphalt aggregate hopper and liquid asphalt oil tank is heated by a 220 volt, 62 kw OSHA required NEMA explosion proof dry well electric heater, thermostat controlled with 25 of cord with dual inline 30 amp fuses with MOV 220 vac surge absorber. The heating system is capable of maintaining heated material up to 300 F. during nonworking hours. TEMPERATURE GAUGES The unit has two 3 dial type, stainless steel temperature gauges that constantly monitor the temperature of the asphalt hopper and road oil tank. HAND TORCH For drying off repair site and cleaning hand tools, the unit has a 200,000 propane BTU hand torch with shutoff valve and 10 of hose with hose rack. Hand torch has mounting bracket for transport. LIQUID ASPHALT OIL PUMP A hydraulically driven, 1 1/2 self priming, variable speed, reversible, rotary gear pump with relief valve. Operating at 20 GPM at 1200 RPM, 100 PSI. The emulsion pump and all oil lines are in an insulated heated area. The pump will circulate the emulsion oil to prevent separation and to crush any lumps that may form and cause clogging of the spray tip. Air injection systems do not have this capability.

2 DIESEL FUEL / RELEASING AGENT STORAGE TANK An 18 gallon capacity tank, equipped with a psi 12 volt DC pump and a hand sprayer for cleaning tools and unit. There shall be a connector valve for flushing road oil pump and lines and a 1 drain. For easy hopper cleaning access and to spray hopper before loading, units with a work deck shall have an additional front mounted spray wand with 3 ft. of hose. LIQUID ASPHALT HAND SPRAYER A 5 x 3/8 wand, equipped with fan nozzle and Deadman Control Valve. Sprayer hose is 15 x 1/2 with a reversible pump and diesel flush system for cleaning pump and lines. HYDRAULIC PUMP The pump is gear type, variable speed at 12 GPM and has an operating pressure of 2000 PSI at 900 RPM. HYDRAULIC OIL RESERVOIR 30 gallon capacity with sight and temperature gauge, ventilated fill cap, 150 micron sump strainer and a 10 micron return filler with 1 gate cutoff valve at filter. HYDRAULIC OIL COOLER An AKG 15 tube hydraulic oil cooler with shroud. Fan operates on 12 vdc and is thermostat controlled at 115 F. HYDRAULIC HOSE AND FITTINGS All high pressure hoses and crimped fittings have a minimum of 9600 PSI burst pressure. HYDRAULIC CONTROL VALVE Five spool, twoway, variable flow with 2200 PSI relief valve. The valve controls hydraulic screw conveyor, hydraulic doors, asphalt agitator, liquid asphalt pump and tool circuit. The valve has an internal or external safety design that will protect the operator and not allow the screw conveyor or asphalt agitator to operate when the doors are open. This system is designed to divert hydraulic oil pressure back to the tank. Electric solenoids on hydraulic valve are not acceptable due to mechanical override feature and ease of bypassing system. The valve is operated from the rear of machine by remote levers. To reduce maintenance problems the main directional control valve stack has no electric solenoids. SCREW CONVEYOR 10 long by 6 diameter progressive screw conveyor has hard surfaced flights welded continuously on 2 scheduled 80 pipe and is ball bearing mounted. Conveyor is driven by a 9200 in.lb. torque variable speed hydraulic motor with forward and reverse. Shall have a delivery chute with 120 of pivot. All bearings can be greased through a feeder line mounted outside the unit from ground level. ASPHALT AGITATOR The agitator shaft is built into the premix hopper and designed to break up asphalt bridging due to vibratory compaction. The scheduled 160 shaft has 12 spikes and is ball bearing mounted and driven by a 9200 in.lb. torque variable speed hydraulic motor with forward and reverse. All bearings can be greased through a feeder line mounted outside the unit from ground level. COLOR Customer s option, standard color is Gloss Black. BIN 30 SPOILS BIN The spoils bin is 30 wide with a 1.25 cubic yard capacity, gravity dump. Asphalt spoils may be loaded or discharged from both sides of the truck. DRIP PAN DRIP PAN A ten (10) gallon drip pan for waste oil combination, for flushing pump, spray wand and lines at the end of the work Day, with necessary valve for draining. FRAME LP BOTTLE FRAME MOUNTED LP GAS BOTTLE 50 Gallon frame mounted LP gas Bottle with quick fill connector, 10 PSI regulator and fuel sight gauge. WORK DECK 24 LUTE HOLDER PTO WORK DECK 24 work deck shall be constructed of ¼ angle iron and 3/16 expanded metal and expanded metal steps with assist hand rails and shall be mounted between hopper and truck cab. Deck provides easy and safe access to emulsion oil tank and asphalt hopper. ASPHALT LUTE AND SHOVEL HOLDER Spring loaded asphalt lute and shovel holders mounted curb side of unit. P.T.O. A Muncie or Chelsea Hot Shift 2

3 ELECTRONIC THROTTLE CONTROL DIESEL HOSE REEL HYD TOOL LINE HOSE REEL HYD 2ND MOTOR HYD STEEL TOP DOORS ELECTRONIC THROTTLE CONTROL A two (2) or three (3) speed, depending on application, rear mounted remote switch allows operator more control over which speed and pressure each particular job requires. As a safety feature, the switch will not function unless the park brake is set on the vehicle. DIESEL FUEL HOSE REEL Hose reel for diesel fuel spray wand has 20 of hose. Reel is spring loaded autoretractable. HYDRAULIC TOOL LINE HOSE REEL Shall be 3000 PSI with dual 25 hydraulic tool lines. Reel is spring loaded autoretractable. HYDRAULIC SECONDARY AUGER MOTOR A secondary, hydraulic, 9200 in. lb. torque, variable speed booster motor installed at rear of auger to assist in dispensing bad or stiff asphalt mix. This also eliminates shearing coupler keys and bolts in the auger shaft. HYDRAULIC OPERATED STEEL TOP DOORS Two (2) hydraulically operated bifold steel top doors with hex brake for rigidity. Doors are insulated with 2 of high temperature insulation in a double steel jacket. The doors have rain seal caps and flex plates to keep asphalt out of door hinges. Each door shall have a 1 ½ bore with 13 stroke hydraulic cylinder with bypass and flow control valves. The controls for doors are at the rear of the unit. Training Local Training and Delivery MSRP $ 76, TCM425DHE DOAS PRICING Standard 425 Patcher (AS DETAILED ABOVE) $ 73, Chassis Option Section Quantity Price Each Price Extended SPECIAL CURRENT MODEL YEAR FREIGHTLINER M2 (CURRENT EMISSIONS)SINGLE AXLE $ 78, $ SPECIAL CURRENT MODEL YEAR FREIGHTLINER M2 (CURRENT EMISSIONS)TANDEM AXLE $ 84, $ Body Option Section Quantity Price Each Price Extended TCM500DHE TCM600DHE 5 CUBIC YARD ASPHALT HOPPER WITH 120 GALLON EMULSION TANK LP BURNERS Requires tandem axle chassis $ 1, $ 6 CUBIC YARD ASPHALT HOPPER WITH 120 GALLON EMULSION TANK LP BURNERS Requires tandem axle chassis $ 2, $ 100 EMULLP Gallon Emulsion Tank FOR LP GAS TCM 425 DHE NC 160 EMULLP Gallon Emulsion Tank FOR LP GAS TCM 425 DHE NC 160 EMULLP Gallon Emulsion Tank FOR LP GAS TCM 500 DHE NC 160 EMULLP Gallon Emulsion Tank FOR LP GAS TCM 600 DHE NC TCM 42580DHED DIESEL BURNER ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 1, $ TCM 50080DHED 5 CU YARD HOPPER DIESEL BURNER ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 3, $ 100 EMUL DIESEL 5 OR 6 YD 100 Gallon Emulsion Tank FOR DIESEL BURNER TCM 425 or 500 DHE NC TCM 42580AEA ALL ELECTRIC AIR INJECTION UNIT WITH 15 CFM HYDRAULIC AIR COMPRESSOR, 19 GALLON AIR TANK 220 VOLT HEATER / 80 GALLON WATER HEATD EMULSION TANK ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 5, $ TCM 50080AEA 5 CU YARD HOPPER ALL ELECTRIC BURNER ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 6, $ TCM 60080AEA 6 CU YARD HOPPER ALL ELECTRIC BURNER ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 6, $ TCM 42580AEE ALL ELECTRIC PUMP TYPE LESS AIR COMPRESSOR 220 VOLT HEATER / 80 GALLON WATER HEATED EMULSION TANK ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 2, $ TCM 50080AEE 5 CU YARD HOPPER ALL ELECTRIC BURNER ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 3, $ TCM 60080AEE 6 CU YARD HOPPER ALL ELECTRIC BURNER ILO LP GAS FOR TCM 425 AS STANDARD ABOVE $ 3, $ 100 EMUL ELEC 425 OR 5 YD 100 Gallon Emulsion Tank FOR ALL ELECTRIC BURNER TCM 425 or 500 AEE $ $ 100 EMUL ELEC 6 YD 100 Gallon Emulsion Tank FOR ALL ELECTRIC BURNER TCM 600 AEE $ 1, $ 120 EMUL ELEC 5 YD 120 or 160 Gallon Emulsion Tank FOR ALL ELECTRIC BURNER TCM 425 or 500 AEE $ 1, $ 120 EMUL ELEC 6 YD 120 or 160 Gallon Emulsion Tank FOR ALL ELECTRIC BURNER TCM 600 AEE $ 1, $ TRANSFER OIL Unit to have TRANSFER OIL HEATING SYSTEM LP AND DIESEL ONLY $ 3, $ NO EMUL TANK REMOVE EMULSION OIL TANK $ (4,266.67) $ LP EMUL TANK Unit WITH LP GAS BURNER IN ROAD OIL (EMULSION) TANK $ 1, $

4 12V CONTROLS STEEL TOP DOORS INSUL TARP COVER WATER TANK CFM AIR COMP 15 CFM AIR COMP 12 VDC incab door controls FOR HYDRAULIC STEEL TOP DOORS $ 1, $ INSULATED TARP TOP COVER The tarp is a double form fitted 2 insulated tarp with tie downs. The tarp material is capable of sustaining 500 degrees F.(MUST REMOVE PART# HYD STEEL TOP DOORS ) $ 1, $ WATER TANK A frame mounted ten (10) gallon tank with valve and hose. Water supply for asphalt compactor plate with rust proof liner. $ $ HYDRAULICALLY DRIVEN AIR COMPERSSOR PSI, 1200 RPM hydraulic driven air compressor with 60 PSI oil pump and cooling fan, used to blow out repair sight and other compressed air demands. Hydraulic and electric controls are located at right rear of unit. Air compressor comes with quick couplers, 20 foot air hose, 5 foot air blow gun with deadman control valve, 5 gallon air tank with cable assisted condensation drain and 150 psi relief valve. $ 4, $ HYDRAULIC AIR COMPRESSOR PSI, 1200 RPM hydraulic driven air compressor with 60 PSI oil pump and cooling fan, used to blow out repair sight and other compressed air demands. Hydraulic and electric controls are located at right rear of unit. Air compressor comes with quick couplers, 20 foot air hose, 5 foot air blow gun with deadman control valve, 5 gallon air tank with cable assisted condensation drain and 150 psi relief valve. $ 3, $ 19 Gallon Air Received Tank ILO Standard 5 Gallon Tank FOR THE HYDRAULIC AIR COMPRESSOR $ $ 80 PSI Protector Valve FOR HYDRALIC AIR COMPRESSOR $ $ REEL COVER FOR Hydraulic Tool Line Hose Reel $ $ AIR LINE HOSE REEL AIR LINE HOSE REEL An air line hose reel with 20 of hose. Reel is spring loaded autoretractable. $ $ STANLEY BR72 PAVEMENT BREAKER Stanley BR72, Pavement Breakers, complete with quick couplers, asphalt cutter, tamper and detachable shank with lockable transporting bracket. $ 3, $ STANLEY BR45 PAVEMENT BREAKER Stanley BR45 lb. Hydraulic Hammer, Pavement Breaker, complete with quick couplers, asphalt cutter, tamper and detachable shank with lockable transporting bracket. $ 3, $ STANLEY BR67 PAVEMENT BREAKER Stanley BR67 lb. Hydraulic Hammer, Pavement Breaker, complete with quick couplers, asphalt cutter, tamper and detachable shank with lockable transporting bracket. $ 3, $ STANLEY BR87 PAVEMENT BREAKER Stanley BR87 lb. Hydraulic Hammer, Pavement Breaker, complete with quick couplers, asphalt cutter, tamper and detachable shank with lockable transporting bracket. $ 3, $ TAMP & SHANK Tamper and detachable shank for PAVEMENT BREAKER $ $ BOMAG BW55E VIBRATORY ROLLER The vibratory roller is a Bomag BW55E with a 4hp Honda Engine, operating weight of 351#, centrifugal force 2250# and single drum vibratory roller 22 wide, centrifugal clutch and water tank. $ 7, $ DOOSAN=SX VIBRATORY ROLLER Doosan Infracore Model SX LB Single Drum Vibratory Roller $ 11, $ WP 1550AW VIBRATORY COMPACTOR PLATE A Wacker WP 1550AW Compactor equipped with a 5.5 hp gasoline Honda Engine with auto oil alarm shut down. Operating weight is 190#, centrifugal force 3375#, plate size19.5 x 23, a water tank and locking holding down brackets $ 2, $ VIBRATORY COMPACTOR PLATE Dolly Attachment $ $ HYD REAR LIFTCOMP HYDRAULIC REAR LIFT PLATFORM FOR COMPACTOR A hydraulically operated lift platform for loading or unloading compactor plate. The platform has a safety latch in the up position, an in cab platform down indicator light with compactor holding down brackets and an optional pavement breaker mount. All controls for platform are at the rear of the unit. $ 2, $ DR SD REAR LIFTCOMP DRIVERS SIDE MOUNT OF COMPACTOR LIFT $ $ ADD Pavement Breaker Mount FOR HYDRAULIC REAR LIFT PLATFORM FOR PVMNT BRKR MT COMPACTOR $ $ AUTO RTN COMP LIFT ADD Auto Return FOR HYDRAULIC REAR LIFT PLATFORM FOR COMPACTOR $ $ REAR LIFT 600 Rear Lift for 600 LB Roller FOR HYDRAULIC REAR LIFT PLATFORM FOR COMPACTOR $ 3, $

5 HYD REAR LIFT ROLLERPV MT AUTO RTN ROLLER LIFT ELEC HOIST BIN 36 HYRAULIC REAR LIFT PLATFORM FOR ROLLER WITH PAVEMENT BREAKER MOUNT A hydraulically operated lift platform for loading or unloading vibratory roller. The platform has a safety latch in the up position, an in cab platform down indicator light with roller hold down brackets and an optional pavement breaker mount. All controls for platform are at the rear of the unit.. Please specify: Driver s side mounted or Passenger side mounted. $ 3, $ ADD Auto Return FOR HYRAULIC REAR LIFT PLATFORM FOR ROLLER WITH PAVEMENT BREAKER MOUNT $ $ ELECTRIC HOIST A 12 volt 1 1/3 hp electric hoist is available for loading or unloading the vibratory compactor plate. $ 1, $ SPOILS BIN 36 (1.5 CU YD wide gravity dump asphalt spoils bin allows spoils to loaded or discharged from both sides of the truck $ $ BIN ELECTRIC UNITS SPOILS BIN FOR ALL ELECTRIC UNITSAlthough this twopiece spoils bin is offered, it is not recommended. An optional twopiece spoils bin for all electric units. Rear mounted bin is.65 cubic yard gravity dump and side mounted bin is.55 cubic yard gravity dump. Only all electric units are available with twopiece spoils bins. $ 2, $ BIN 1.5 YD ELECTRIC SPOILS BIN FOR ALL ELECTRIC UNITS 34 wide, 1.50 cubic yard Dump $ 3, $ BIN 2 YDELEC SPOILS BIN FOR ALL ELECTRIC UNITS 2 cubic yard Hydraulic Dump Spoils Bin $ 3, $ TACK HOSE REEL TACK OIL HOSE REEL Hose reel for tack oil has 15 of hose. Reel is spring loaded autoretractable $ $ AIR & TACK HOSE REEL Dual Feed Hose Reel, Air and Tack $ $ FRAME MOUNTED 35 GALLON LP GAS BOTTLE ILO OF 50 GALLON AS STANDARD FRAME LP BOTTLE 35 ABOVE A frame mounted 35 gallon capacity LP Gas Bottle with quick fill connector, 10 psi regulator and fuel sight gauge. $ (133.33) $ LP HOSE REEL LP Gas Hose & Reel $ 1, $ REMOVEABLE BOTTLE 100 lb. (25 gallon) removable propane bottle complete with 10 PSI regulator valve. $ $ STROBE LIGHT STROBE LIGHT A pedestal mounted Meteorlight model SY2000. $ $ 10LIGHT DIRECTIONAL ARROW BOARDLED The arrow board is an Able 2 with arrow ABLE 2 10 LIGHT flashing left, right and warning bar. The board is mounted on the rear of the patch unit ARROW BOARD LED with in cab controls. $ 1, $ 14LIGHT DIRECTIONAL ARROW BOARDLED The arrow board is Wanco WSBAL14 WANCO WSBAL14 (L.E.D.) board has State D.O.T. approved 14 seal with arrow flashing left, right and ARROW BOARD LED warning bar. The board is mounted on the rear of the patch unit with incab controls. $ 2, $ HYD ARROW BOARD Hydraulic 2 side Arrow Board $ 3, $ HYD ARROW BOARD STROBE Hydraulic 2 side Arrow Board with Center Mount Strobe $ 4, $ WORK LIGHTS WORK LIGHTS Two (2) 5 adjustable flood work lights mounted rear top corner of hopper. $ $ SAND SPREADER SAND SPREADER ASSEMBLY The Sand Spreader Assembly includes chute, spinner, hydraulic motor, hydraulic hoses, hydraulic valve and quick coupler connecting fittings. The controls are incab 12 VDC electric. For safety purposes, NO hydraulic high pressure hoses are in the cab. $ 5, $ ASPH EDGER 20HPLP ASPHALT EDGER Edger is designed to repair deteriorated shoulders on roads and repair water cuts and long trenches. Screw conveyor assembly is ball bearing mounted, conveyor is driven by a hydraulic motor with forward and reverse capabilities. Edger is powered with a 20 HP Kohler Model CH20S LP Gas auxiliary engine with direct mounted hydraulic pump. Unit mounts to rear of patch unit with 4 bolts. Has separate asphalt chute. Hydraulic splitter valve allows separate control from hopper screw conveyor to side deliver screw conveyor. Screw conveyor is fully enclosed for safety. $ 6, $ ASPH EDGER 21 HP DIESEL ASP EDGER LOAD SENSE PUMPDIESEL PTO CS PTO MUNCIE TG PTO MESH DIRECT ELECTRIC PTO CRANK FRONT ELECTRIC ASPHALT EDGER WITH: 21 HP Lombardini Air Cooled Diesel Engine $ 9, $ ASPHALT EDGER WITH LOAD SENSE PUMP Edger is powered by a load sense variable displacement crankshaft driven pump. This will operate the edger assembly as well as other components of the unit. This eliminates the need for a transmission mounted PTO. However, the truck chassis must have minimum of frame extension and accommodate pump and drive line (i.e. hood, radiator location, etc.). Available with diesel engine only. $ 7, $ PTO OPTION Hot Shift CS6 series (or equivalent): For Allison 2000 Series Transmission(MUST REMOVE PART # PTO ) $ 2, $ PTO OPTIONMuncie TG Series Electric Over Air shift (or equivalent) when applicable(must REMOVE PART # PTO ) $ 1, $ PTO OPTIONAll Electric Units Constant mesh PTO with Direct Mount Load Sense Pump(MUST REMOVE PART # PTO ) $ 4, $ PTO OPTIONAll Electric Units Crankshaft Driven Front Mount Load Sense Pump(MUST REMOVE PART # PTO ) $ 3, $

6 ELECTRIC THROTTLE CONTROLMANUAL THROTTLE CONTROL FOR MANUAL ENGINES Muncie HydroThrottle with rear manual override cable. (MUST REMOVE PART # ELECTRIC THROTTLE CONTROL ) $ $ HIGHWAY WARNING TRIANGLES EXTRA TOOL BOX A Highway warning triangle kit consisting of three (3) reflective triangles in a storage case. A 12 gauge steel 19 x 24 x 30 TOOLBOX with water proof locking door. $ $ $ $ WORK DECK Wide work deck ILO STANDARD (MUST REMOVE PART # WORK DECK 24) $ 1, $ WORK DECK Wide work deck ILO STANDARD (MUST REMOVE PART # WORK DECK 24) $ 1, $ SHOVELING APRON FIXED Apron is constructed of 3/16 steel with FIXED bottom, mounted on platform below asphalt dispenser. $ $ SHOVELING APRON FOLDING LIQUID ASPHALT OIL TANK BURNER TRAFFIC CONE RACK Apron is constructed of 3/16 steel with HINGED AND FOLDING bottom, mounted on platform below asphalt dispenser. LIQUID ASPHALT OIL TANK BURNER To enable units to work emulsion or asphalt cut back oils, tank is equipped with a dry radiant chamber with a 150,000 BTU LP gas retort tube burner 10 psi, thermostat controlled, 12 volt dc electronic igniter with safety shutoff on loss of flame or excessive temperature. Set of two (2) frame mounted traffic cone racks with holding capacity of ten (10) 28 tall cones. $ $ $ 1, $ $ 1, $ ASPHALT LUTE 30 wide aluminum asphalt lute with 7 ft. handle. $ $ ASPHALT SAW Stanley C hydraulic hand held cut off and asphalt saw. $ 3, $ LP GAS HOSE REEL LP gas hose reel with 20 of hose. $ $ LP GAS HOSE REEL ELECTRIC UNITS LP GAS HOSE REEL (All Electric) 200,000 BTU Hand Torch with 25 lb LP Gas Bottle $ $ HEATED TACK OIL HOSE ½ x 15 foot of heated hose. Operated at 110 VAC, 50 watts per foot. Max operating temperature is 180 F. Equipped with thermocouple, 110 VAC thermostat, and 12 VDC to 100 VAC power inverter, 3/8 x 5 foot wand with deadman valve. $ 3, $ WC 3 GALL Water Cooler and Rack 3 gallon $ $ WC 5 GALL Water Cooler and Rack 5 gallon $ $ BACKUP CAMERA Backup Camera SYCS7LCD66 Kit1 Color $ $ Chassis Total $ Options Total $ NEW Sales Price $73,782.00