Custom Vac 822 Hydrovac with the following specifications (Tri Drive Mounted):

Size: px

Start display at page:

Download "Custom Vac 822 Hydrovac with the following specifications (Tri Drive Mounted):"

Amie Stone
5 years ago
Views:

1 822 HYDROVAC Custom Vac 822 Hydrovac with the following specifications (Tri Drive Mounted): DESIGN: Vessel designed and constructed in full compliance with Transport Canada TC 407/412 and CSA B Debris Compartment: Tank diameter 78" (12' seam to seam) 78" x 5/16" F & D heads 78" x 5/16" shells Formed angle front & rear pedestals Three 4" roll bars Three external reinforcement rings Reinforcing pads for all tank attachments Tank Lock Down Assembly to meet current B620 Code 8" Primary shut off assembly with 8" flanged outlet 8" isolation shut off air actuated Recessed liquid level indicator D/S Full opening rear door c/w six pinwheel door locks 6"Brass Suction valve c/w 6" sandpipe, aluminum camlock/cap D/S 4"Brass Suction valve c/w aluminum camlock and cap P/S 12" Hydraulic flange mounted mudgate with sliding lock mechanism and 4" Brass valve with aluminum camlock and cap All rear valves heated, and equipped with air/open spring/close air actuators & control switches Operating Temperature 20 deg F to 200 deg F Vessel hydrotested to 40 PSI

2 Blower Specifications & Allied Equipment: Hibon SIAV CFM free air rating 27" Hg Maximum sea level 8' Four Way Diverter valve ( Vacuum to Pressure Mode ) 8" Double door check valve ( to prevent blower back spin ) Prestage filter assembly c/w 16" filter One intake silencer, One exhaust silencer 8" cyclone with bottom cleanout door & 2" heated drain valve Hydraulic System (Linde closed loop design) : Boom: 8 Bolt PTO for blower 6 Bolt PTO for wash Hydraulic pump and motor for blower Hydraulic pump and motor for Triplex pump Tandem gear pump for Auxiliary functions High torque/temp drive coupler with flex insert Spool type valve control bank for pump and allied functions Rear control section for door and Dumpgate on deck D/S Joystick speed control for blower Torque control for vac pressure 90 gallon oil tank c/w vent, site glass, filters, temperature gauge, and inspection hatch Two 12 volt oil coolers 3 stage hydraulic hoist cylinder 8" x 270 deg telescopic suction boom 12" knife gate gate valve assembly with shear section 2

3 Accumulator for knife gate code compliance 8" boom hose with end One wireless remote controller One hard wired pendant controller for backup Plumbing: 8" piping c/w 8" oil & gas loop hose Wash System: Cat 3560 Triplex plunger pump rated psi 2" Bronze strainer,1" high pressure Baird relief valve, Three Hydraulic Rewind Reels 100' x 1/2" pressure hose 100' x 3/8" temperature rated Steam hose 100' x 3/8" degreaser hose Note: Wash Systems Are Winterized For Cold Weather Operation Wash Accessories: One wash gun, wand, nozzle and quick coupler One steam wand, nozzle and quick coupler One 6' Hydro Dig Wand c/w 4' extension and Turbo Nozzle One degreaser tank assembly c/w tank, stand, pump, gun, wand, and nozzle Hot Water System: Hotshot 980,000 BTU/hr heater c/w relief valves temperature gauge; Honeywell control,diagnostic panel 2000 Watt Pure Sign Inverter Wet Steam kit plumbed with high pressure ball valves Safety Feature: a 340 deg. Auto Shut Off on Heater System New style 18 GPM solid brass Flow Switch with no bypass line All plumbing stainless steel 3

4 Wash Cabinet: Milron Aluminum Crossover cabinet c/w Large doors D/S, P/S Small access door in large door P/S for hose access Heaters, LED Lights, and Auto Vent Water Compartment ( 4 Cubes 880 Imp Gal ): 20" top mounted Manway Stainless steel liquid level indicator assembly P/S 2" heated fill, breather and suction 2" heated drain valve air actuated, Switch control at operator station 2" heated hard pipe supply direct connection through cabinet to triplex 2" heated Vac/water changeover valve air actuated Vibrator: Global hydraulic vibrator assembly mounted on bottom of tank with reinforcement pads, heavy duty mounting channel and pressure relief valve. Pressure Relief: One 3" x 30 PSIG pressure relief vent One 2" PRV in lower suction pipe 2" vacuum breakers installed on exhaust silencer Gauges: Gauge assembly with tank vacuum/pressure gauge, hydraulic pressure gauges. Blower temperature gauge remote mounted on D/S. Frame, Deck and Bumper: Full length subframe c/w 1/8" checker plate hose tray/fender assembly c/w heavy duty outrigger supports,1 1/4" tube handrails, close in plate. Code rear bumper with light boxes and rear tire skirt Subframe supports decking, rear hoist hinges & front hoist cradle 4

5 Cabinets: One steel 72" three door deck box Two rear skirt fitting boxes Electrical System: Waterproof main circuit control box self contained power supply. Sealed wire harness c/w waterproof junction boxes. L.E.D. lamps (Clearance, park, signal). Sealed L.E.D. reverse lamps. Four L.E.D. style work lights L.E.D. WORK LIGHTS on the Boom Frame Electrical system shut down at key. Sealed rear skirt lamp modules. Stop and turn L.E.D sealed lamp modules on top ring of door. Back up alarm. Truck cab and deck mount blower switches Additional Equipment: Catwalk & ladder on upper suction pipe driver's side. PTO Hour meter installed in truck cab Chain hanger, slide out style Mudflaps 50'ground cable ( wind up style ) Ground studs mounted off rear peds D/S & P/S 30# fire extinguisher/brkt/cover Boom hose holders P/S Two 6" x 5' aluminum dig tubes with Band Clamp ends one with rubber tip One 8" x 6" x 4' aluminum adapter 5

6 Paint: The entire tank and body of vacuum system shall be sandblasted, primed and painted with Endura paint Water Tank Lined With Devoe 233 Other Items: Operators manual issued with completed unit Unit includes (NSM) National Safety Mark One year Manufacturer Ltd warranty Installation: Complete system installed on Customer Tri drive truck chassis NOTE: Any relocation of truck parts or frame alterations may result in additional Labor charges: Any additional equipment request not on this quote parts, and labor will be added to final price. Custom Vac Services Ltd reserves the right to engineer and manufacture it's products in accordance with it's warranty and design policies. For more information please contact Custom Vac Services Ltd. Head Office Custom Vac Services Ltd Avenue Nisku, AB Canada T9E 1B7 Tel: (780) Fax: (780) /1/

INDUSTRIAL SERVICE TANKS

INDUSTRIAL SERVICE TANKS Glendale Service s are designed and built with you in mind. We ensure every PWT and VST Series tank is tailored to load quickly and efficiently. Over 25 years of experience, certified