2017 Single Axle 5 CU.YD. Dump Truck Specifications. Minimum Specifications 33,000 lb
|
|
- Wendy Carr
- 6 years ago
- Views:
Transcription
1 2017 Single Axle 5 CU.YD. Dump Truck Specifications Item GVW Wheelbase Cab to Axle Minimum Specifications 33,000 lb 158 inches 84 inches Tires 11R x 22.5, Tubeless, 14 ply, All weather mud and snow tread front(2) and (4 rear) Wheels Disc, 22.5 x 8.25 tubeless rim Axles Front 14,000 lb. Rear 23,000lb. limited slip differential with front auxiliary helpers, driver controlled locking differential Shock absorbers Heavy Duty front and rear (as offered by the manufacturer as standard equipment) Brakes Air ABS 4-channel Bendix brake system with air activated spring loaded parking brake with automatic neutral, low pressure warning light and alarm, front and rear dust shields and engine driven compressor Frame Black painted 120,00 PSI tensile strength and a RBM of 2,100,000 minimum with 8 extensions to front bumper and frame to accommodate plow frame and front tow hooks Steering Fuel tank DEF tank Power assisted Minimum 50 gallon capacity, and minimum 5 gallon Electrical 12 volt batteries(2) with jump start terminals 130 amp alternator, box on frame, heavy duty starter, electric horn, trailer electrical connections routed to end of frame, with RV type 7 pin connector. LED strobes mounted in front, top of cab shield, recessed, controlled from a cab mounted switch. A 12 volt power outlet and provision for electric trailer brakes. Plow lights wired and mounted to the hood. A manual reset circuit breaker.
2 Engine Inline 6, wet sleeve. 270hp Diesel, 800 ft. lbs torque all minimum. Heavy duty dry air filter with air restriction indicator, Heavy duty radiator with -20 degree anti-freeze, Internal oil cooler, 1000 watt block heater minimum and horizontal exhaust. Transmission Dash mounted shifter, 6 speed Automatic Allison 3500 RDS Cab/Hood Conventional, Tinted glass, dome light, full suspension, manual adjusted high back driver, and non suspension, high back passenger seat, with under seat storage if available. Deluxe HVAC heater/defroster, fresh air filter, two speed intermittent wipers, AM/FM radio, air conditioning, power accessory outlet. Exterior painted white, interior gray. 3 piece hood if available Gauges Speedometer, Voltmeter, oil pressure, temperature, fuel level, tachometer, transmission temperature. DEF with level indicator. Mirrors 2 Heated 16 x 7 west coast type retractable stainless steel with 8 convex on each side Bumper, Grille, Hitch, Swept back front bumper, rear frame mounted trailer hitch, meeting category II specification for tongue weight, pintle type hitch, 20 from ground to riding surface. Stationary front grille, Does not tilt with hood for mounting snow plow frame. Power Take-off Crank shaft driven pump. (electric hand throttle), IP mounted, when activated engine RPM adjusts, set up by dealer or bed supplier Safety and warranty Vehicle must conform to all state and federal health, safety, emissions, lighting, and noise regulations. Full factory warranty, a copy of which is to be provided with bid Manuals and keys Supply two sets of keys, operator s, shop repair, and a parts manual for entire unit and attachments
3 Bed, Hydraulics, Snow plow, V box Material Spreader This specification will describe a Henderson HDSA, Heil HM, or equivalent type dump body, with all components needed for complete operational unit Bed 10 long, 5 cu. Yd. capacity, 84 inside width, minimum 24 high sides, with heavy duty side boards. head sheet, and tailgate minimum 32 high with ½ cab shield, painted Grey. Asphalt shield. Include mud flaps. Automatic tarp, controlled from a switch in the cab. Sides and head sheet One piece sides and head sheet to be 10 gauge with smooth sides 10 gauge boxed top rail and bottom rub rail seamless and sloped outward. Full height tapered front corner posts with 2 side board pockets, 10 gauge full depth 5 ¾ x 12 rear apron reinforced with ¼ plate to strengthen latch assembly. 4 Heavy duty, 4 wide, ratcheting tie downs welded to the bed side close to the bottom on the outside. Floor 8 gauge class 50 floor with 2 floor to side radius, with stacked 4 x 5.4 lbs. per foot longitudinal structural channels Tailgate 10 gauge full perimeter boxing, flush mount ½ cut pivots, heavy duty offset hinge plates, ¾ latch hooks with dual 3/8 latch plates, 1¼ upper and lower pins, air operated, driver s station mounted control for latching/releasing. Pivot points include stainless steel bushings Hoist and sub frame Class 50 rating single cylinder, twin push arm underbody, 7 cylinder, 2 ½ O.D. chrome plated piston rod. 4 structural channel sub frame, 1 ½ hinge pins Lighting LED recessed into corner post, meeting all state and federal safety regulations Hydraulic system Load sensing central hydraulic system, hydraulic pump, driven off the crank shaft, capable of 26 GPM at 3000 psi at 2400 rpm. Case drain directed back to tank not passing through filter. Pump must have internal bleed down compensator. Hydraulic valve shall be capable of 30GPM with published flow curves to 40 GPM, with load sensing individual flow control compensators on each section.
4 Inlet cap with inlet, outlet, and load sense ports, valve arrangement as follows; *single acting cylinder spool for hoist, spring return, with section flow compensator *single acting cylinder spool for snow plow lift, spring return with section flow compensator *single acting cylinder spool for angling snow plow *single acting motor spool one each, for spinner, and for auger/conveyor, proportional 12 VDC spring center with manual override outlet cap with pressure reducing valve and solenoid drain *single acting cylinder will be actuated by Morse RVC cable control system, cable core must be stainless steel, capable of 100 lbs. push/pull with controls mounted next to driver, single axis control for dump and joystick(t pattern) controls for plow lift and angle. Cab mounted electronic spreader control, with ground speed to control salt distribution, also with color camera mounted to the rear of the salt spreader and color monitor to be mounted in the cab to be easily in view of the driver. Filter will be spin on element with 1 1/4' NPT ports mounted as close as possible to the reservoir. By pass and condition gauge are required. Reservoir shall be 30 gallon minimum capacity screened fill neck, sight glass and temperature gauge, magnetic drain pump and suction screen, mounted to side of truck frame. Appropriate size hydraulic hoses plumbed to external lower right rear of bed for spreader and plumbed to front bumper with 2 excess hose for plow operation, all with universal ball type quick connect ends. Snow plow *11 x 36 high hydraulic angle and lift, truck mounted plow * No less than 3/16 or 8 gauge steel constructed moldboard with ½ vertical ribs and curb guard * 1 x 6 steel runners with jack screws * plow lights * universal quick hitch mounting * adjustable compression spring trip mechanism * standard hole punch 5/8 by 8 carbide insert replaceable cutting edge. * rubber deflector across top edge of moldboard, with spring loaded positioning markers mounted on the upper corners of moldboard visible to driver with blade in full down position
5 * moldboard primed and painted standard color,(safety orange, safety yellow, or black are acceptable) * repair parts list and manual if available Pre-wetting liquid spray system Minimum body requirements Drive system: All components are mounted and sealed, corrosion resistant, molded fiberglass housing with hinged cover. Hydraulic drive motor is 1.21 CIR geroler type. Liquid pump is a RPM gear type of corrosion resistant materials with carbon graphite bearings. All tubing is stainless steel with corrosion resistant JIC fittings. Liquid output is controlled by an adjustable flow control valve on the hydraulic drive motor input. Flow divider valve is manually adjustable with control from zero to maximum flow for increasing or decreasing saturation of granular material. Cab mounted controls: On/off switch with power indicator. High pressure and tank empty indicator lights with audible alarm. Heavy duty wiring harness from cab to pump. Weather and corrosion resistant sealed connectors with protective caps. Reservoirs: (2) 75 gallon rotation molded medium density polyethylene tanks with 5 diameter cap. Replaceable screen line strainers. Corrosion resistant shut off valves. Reservoir tank is angle formed, internal baffle, to be mounted to each side of the slip in v-box salt/sander. Metering orifice: Variable displacement orifice provides an extended range of outputs located in the spinner chute. material Mounting: All bolt-on (no welding required) brackets, hardware, and fittings supplied. Material spreader *truck mounted 10 V-box type *5.5 to 6.5 cubic yard capacity *minimum 50 tall sides
6 *304 unpainted stainless steel construction of no less than 10 gauge sides and a minimum 7 gauge floor *adjustable all steel pintle type conveyor chain Trade in unit 2000, Chevrolet C-70, single axle 5 yard dump truck. Can be seen during regular business hours at 601 NW 2 nd Street in Abilene. Finance Options The City of Abilene desires to enter into lease/purchase agreement. They would also retain the option to seek like financing from their local financial intuitions'. Please submit your financing rates and services along with the equipment bid in a separate envelope for our review. Any questions or concerns please contact Lon Schrader or Joe Hawk, at Public Works, (785)
Request for Bids INFORMATION FOR BIDDERS. FURNISH THE CITY OF DERBY, KANSAS, ONE (1)2014 or NEWER TANDEM AXLE 10 YARD DUMP TRUCK w/ PLOW
Request for Bids City of Derby Public Works 2015-027 INFORMATION FOR BIDDERS FURNISH THE CITY OF DERBY, KANSAS, ONE (1)2014 or NEWER TANDEM AXLE 10 YARD DUMP TRUCK w/ PLOW 1. Sealed bids, on the attached
More informationGALLATIN PUBLIC UTILITIES
GALLATIN PUBLIC UTILITIES Bid Proposal Item: Single Axle Dump Truck Bid Date: Company Address: Phone Number: Manufacturer: Bid Information (1) Prices F.O.B., 249 Hancock Street, Gallatin, Tennessee 37066.
More informationREQUEST FOR QUOTATIONS
Public Works Department REQUEST FOR QUOTATIONS 12 14 YARD DUMP TRUCK PURCHASE Due: Thursday, July 27, 2017 No later than 2:00 P.M. Submit to: City of Arroyo Grande Attn: Public Works Department 1375 Ash
More informationTOWN OF FARRAGUT. Bid Specifications For 2017 Dump Truck. William McKelvey Public Works Director Municipal Center Drive Farragut, TN 37934
TOWN OF FARRAGUT Bid Specifications For 2017 Dump Truck William McKelvey Public Works Director TOWN OF FARRAGUT 11408 Municipal Center Drive Farragut, TN 37934 (865) 966-7057 BID SPECIFICATIONS for 2017
More informationTender Town of Yarmouth Equipment Purchase 5 Ton Single Axle Truck Complete with dump box, slide-in spreader, pre-wet system, and spreader controls.
Tender Town of Yarmouth Equipment Purchase 5 Ton Single Axle Truck Complete with dump box, slide-in spreader, pre-wet system, and spreader controls. General Instructions: 1. All bids must be submitted
More informationINSTRUCTIONS TO BIDDERS AND SPECIFICATIONS FOR A 7-8 CUBIC YARD DUMP TRUCK
INSTRUCTIONS TO BIDDERS AND SPECIFICATIONS FOR A 7-8 CUBIC YARD CITY OF FOREST 120, SOUTH DAVIS ST P.O. BOX 298 FOREST, MS. 39074 RE: One or More New Dump Truck, Purchase And / Or Lease Purchase Financing.
More informationThe bidder shall furnish a complete set of Operator, Service, and Parts Manuals with each body sold.
2013 Model or current production year 34,000 G.V.W.R. Cab and Chassis INTENT: These specifications describe a Dump Truck. GENERAL TERMS: All equipment furnished under this contract shall be new, unused,
More informationALLEGAN COUNTY ROAD COMMISSION PROPOSAL FOR WESTERN STAR TANDEM REAR AXLE DUMP TRUCKS (CAB & CHASSIS) MINIMUM 64000# GVWR
ALLEGAN COUNTY ROAD COMMISSION PROPOSAL FOR WESTERN STAR TANDEM REAR AXLE DUMP TRUCKS (CAB & CHASSIS) MINIMUM 64000# GVWR Board of County Road Commissioners of the County of Allegan 1308 Lincoln Road Allegan,
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours of
More informationCity of New Haven. 101 FRONT STREET PO BOX 236 NEW HAVEN, MO Phone * * Fax
City of New Haven 101 FRONT STREET PO BOX 236 NEW HAVEN, MO 63068 Phone 573-237-2349 * www.newhavenmo.org * Fax 573-237-4696 August 20, 2014 Request for Bids, Medium Duty Truck City of New Haven The City
More informationALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS
ALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS PROPOSAL FOR DUMP BOX BODIES, V BOX SPREADERS, UNDER BODY SCRAPERS, PLOW WINGS, FABRICATION AND ASSEMBLY OF COUNTY DUMP TRUCKS Board of County Road
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours
More informationCOLLEGE COMMUNITY SCHOOL DISTRICT BID SHEET. THREE (3) 78 PASSENGER TRANSIT STYLE SCHOOL BUSES and ONE (1) 65 PASSENGER LIFT BUS
COLLEGE COMMUNITY SCHOOL DISTRICT BID SHEET THREE (3) 78 PASSENGER TRANSIT STYLE SCHOOL BUSES and ONE (1) 65 PASSENGER LIFT BUS Bid #1 Three (3) 2010 (78) Passenger Transit Style School Buses and One (1)
More informationType 3 Fire Engine Model 346
Type 3 Fire Engine Model 346 Issue Date: February 2016 Supersedes: February 2014 Type 3 Fire Engine, Model 346 Supersedes February 2014 Page 1 Table of Contents Record of Revisions 3 1 General 4 1.1 General
More informationMONTGOMERY COUNTY PUBLIC WORKS DEPARTMENT P. O. BOX 663 INDEPENDENCE, KANSAS PH FAX
MONTGOMERY COUNTY PUBLIC WORKS DEPARTMENT P. O. BOX 663 PH. 620-330-1170 - FAX 620-330-1177 MEMO To: From: Dump Truck Bidders Jim Wright Asst. Public Works Coordinator Date: February 23 rd 2016 Subject:
More informationSPECIFICATIONS FOR 4X4 SINGLE AXEL PLOW TRUCK. City of Negaunee
SPECIFICATIONS FOR 4X4 SINGLE AXEL PLOW TRUCK City of Negaunee The following specification describes the minimum requirements for a 4x4 single axel plow truck for the City of Negaunee. The equipment bid
More informationINVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL / CNG OPTIONS
P. O. B o x 1 5 4 0 T h o m a s v i l l e, G A 3 1 7 9 9 2 2 9-227- 7 0 0 0 F A X 2 2 9-227- 3 2 4 3 w w w. t h o m a s v i l l e. o r g INVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL
More informationMANISTEE COUNTY ROAD COMMISSION 2019 TANDEM AXLE TRUCK SPECIFICATIONS AND BID REQUIREMENTS (ALTERNATE BID) January 4, 2018
GENERAL 1. The following minimum specifications are for a tandem axle truck (conventional cab and chassis with an engine and transmission). 2. The truck shall be the manufacturer s current model under
More informationMEYER MATE 9.0 CU FT. SPREADER
MEYER MATE 9.0 CU FT. SPREADER General Specifications Overall Height: 41.25" Overall Width: 49.5" Overall Depth: 32" Weight Empty: 140 lbs. Spreading Width: Minimum 3 Maximum 30 Spreading Material: Dry
More informationTAILGATE SPREADERS The most cost-effective high quality tailgate spreaders in the industry.
SaltDogg Mean On Ice, Man's Best Friend. SaltDogg has the cost-effective, quality spreader you need with everything from manual walk-behind spreaders to insert salt spreaders and tailgate spreaders to
More informationInvitation No: Additional available options:
Invitation No: 044-14 Additional available options: The choice of any of these options, is in lieu of, or in addition to the base bid for the State of Ohio and subject to final engineering approval. Some
More informationChecklist for Preparing Basic Motor Grader (29,000 lbs. class) Specifications
Purdue University Purdue e-pubs Indiana Local Technical Assistance Program (LTAP) Publications Indiana Local Technical Assistance Program (LTAP) 1983 Checklist for Preparing Basic Motor Grader (29,000
More informationHEAVY DUTY TRUCKS. Business Rack Clock Digital $
IFB No. 2016-002 for 2017 Vehicles Group I Dealer Name: Date: Minimum Specifications for ALL Heavy Duty Trucks are as Follows: Driver Air bag, Arm Rests - All Doors, Factory Air Conditioning, Factory Auxiliary
More informationNOTICE TO BIDDERS. ONE (1) NEW TANDEM AXLE TRUCK (cab & chassis)
NOTICE TO BIDDERS The Roscommon County Road Commission will receive sealed bids until 2:00 p.m. on Thursday, March 22. 2012. (Bids will be opened at 2:00 p.m. for tabulation and review. Bid results and
More informationREQUEST FOR SEALED BID CAB/CHASSIS FOR MEDIUM DUMP TRUCK WITH SALT SPREADER NOVEMBER 18, 2015
REQUEST FOR SEALED BID CAB/CHASSIS FOR MEDIUM DUMP TRUCK WITH SALT SPREADER NOVEMBER 18, 2015 Sealed bids will be received until 2:00 p.m. on Monday, December 7, 2015, by the City of Martinsville, to contract
More informationNELSON COUNTY FISCAL COURT
NELSON COUNTY FISCAL COURT Specifications/Bid Forms FOR 25 CUBIC YARD REAR PACKER,REAR EJECTION, GARBAGE TRUCK DATE: 08/2017 ADVERTISEMENT FOR BIDS The Nelson County Fiscal Court will accept sealed bids
More informationREQUEST FOR QUOTATION
REQUEST FOR QUOTATION Sealed quotations will be received by the CAO/Clerk until: Wednesday, July 6, 2016-11:00 am QUOTATION FOR: PICK-UP TRUCK All items must be submitted on Quotation Forms, in sealed
More informationSPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs
Page 1 of 5 SPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs Insulated Telescopic Articulating type aerial lift with the following
More informationFLAT BED STAKE BODY TRUCK
Group 1 Contract Attachment 4 Price Sheet: Dump Trucks Please see Attachment D: Instruction and General Information for Instructions, Color Key, and Reference Key. GVWR* Code 2 Base Vehicle Description3
More informationISUZU NPR-HD REG CAB CAB & CHASSIS SPECS 14,500# GVWR DSL
MODEL YEAR 2014 MANUFACTURER ISUZU MODEL NPR-HD DSL GVWR 14,500# *Optional Wheelbases WHEELBASE 109.0 132.5 * 150.0 * 176.0 * CA DIMENSION 86.5 110.0 127.5 153.5 BOC DIMENSION 7.7 7.7 10.2 10.2 USABLE
More informationGENERAL SPECIFICATIONS FOR END DUMP WITH PLOW AND SPREADER
GENERAL SPECIFICATIONS FOR END DUMP WITH PLOW AND SPREADER Any additions, deletions or variations from the following specifications must be noted. Any items appearing in the vehicle manufacturers regularly
More informationTruck Specs. Sabre 9 Off-Highway GCWR: 242,000. CapacityTrucks.com
Truck Specs Sabre 9 Off-Highway GCWR: 242,000 CapacityTrucks.com Sabre 9 / Off-Highway - Base Model Base Model Sabre 9 / Off-Highway Basic Overview GCWR: 242,000 Basic Overview Axle: 4x2 Basic Overview
More informationTMS x 4 & 6 x 6
TMS5 6 x 4 & 6 x 6 Dimensions 8' (2438) TAILSWING 11' 1" (3383) 7' 8" (2337) RET 13' 9-3/4" (4210) MID EXT ' (96) EXT Note: ( ) Reference dimensions in mm 16-3/4" (425) 43' 4" (13 8) OVERALL 10' 10" (32)
More information145 HP, FRONT WHEEL ASSIST TRACTOR 3/17/15 Page 1. Mountrail County Road and Bridge SPECIFICATIONS FOR
Page 1 Mountrail County Road and Bridge S FOR Bidder's Instructions: Indicate compliance to the specifications on the YES/NO line by each specification. Indicate any deviations from the specifications
More informationISUZU N-SERIES (REG CAB) DIESEL CAB/CHASSIS SPECS NPR-HD (14,500# GVWR)
MODEL YEAR 2017 MANUFACTURER ISUZU MODEL NPR-HD (diesel) GVWR 14,500# *Optional Wheelbases WHEELBASE 109.0 132.5 * 150.0 * 176.0 * CA DIMENSION 86.5 110.0 127.5 153.5 BOC DIMENSION 7.7 7.7 10.2 10.2 USABLE
More informationMantis Rerailer General Specifications
2008 General Specifications 1. Typical Operating Parameters 2. General 1.1 Operating temperatures will typically be between 20 F (7 C) to 110 F (43 C). 1.2 Relative humidity ranges between 20% and 100%.
More informationPennsylvania State Police Tactical Mounted Unit. 25,500# GVWR Crew Cab Tractor
Pennsylvania State Police Tactical Mounted Unit 25,500# GVWR Crew Cab Tractor The following pages specify the design and component requirements for a crew cab truck tractor. In addition to the vehicle
More informationPRODUCT LINE WHEELBASE & CAPACITIES
PRODUCT LINE WHEELBASE & CAPACITIES TX-4030 (30,000-lb. Cap. at 36" L.C., 132" WB) Rigger Application: 40,000-lbs. Cap. at 36 L.C. if traveling less than 1 mph up to 48-in. lift. Truck is shown with available
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on one knuckle boom trash loader for the sanitation department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on one knuckle boom trash loader for the sanitation department. Specifications may be obtained from the Public Works Department at City Hall between
More informationQUOTE For a 2017 Fire Department Conventional Truck Chassis-Water Tender With PTO Pump
Town of Wascott PO Box 159,Wascott, WI 54890 Phone: 715/466-4252 Email: wascott@centurytel.net QUOTE For a 2017 Fire Department Conventional Truck Chassis-Water Tender With PTO Pump Note: Bidders must
More informationTXB-250M. The master parts depot ships genuine TAYLOR parts nationwide and is a key component in the Sudden Service, Inc. dealer network.
PRODUCT LINE WHEELBASE & CAPACITIES TXB-180S (18,000-lb. Cap. at 24" L.C., 110" WB) TXB-200S (20,000-lb. Cap. at 24" L.C., 110" WB) TXB-250M (25,000-lb. Cap. at 24" L.C., 121" WB) TXB-300L (30,000-lb.
More informationFLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES
P a ge 1 FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES *Effecitive dates for Bid 15-11-0116 are: February 1, 2015 through March 31, 2016. SPECIFICATION
More informationRUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION
RUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION A DIVISION OF PB9600 STANDARD PLATFORM/ STAKE BODIES SHOWN EQUIPPED WITH 12' Body with Optional Wood Floor Triple Window in Bulkhead Stake
More informationTXB-250M PRODUCT LINE WHEELBASE & CAPACITIES. (30,000-lb. Cap. at 24" L.C., 140" WB)
PRODUCT LINE WHEELBASE & CAPACITIES TXB-180S TXB-200S TXB-250M TXB-300L (18,000-lb. Cap. at 24" L.C., 110" WB) (20,000-lb. Cap. at 24" L.C., 110" WB) (25,000-lb. Cap. at 24" L.C., 121" WB) (30,000-lb.
More informationRAC EXPORT TRADING Germany Tel
Technical Specification Kenworth 963S oilfield truck, new GAWR RATINGS Front Axle Weight Rating 40.000 Lb. 18.140 kg Rear Axle Weight Rating 150.000 Lb 68.030 kg Gross Vehicle Weight Rating 190.000 Lb.
More informationInvitation to Tender. District of Taylor MOTOR GRADER
Invitation to Tender District of Taylor MOTOR GRADER Sealed tenders clearly marked Motor Grader will be received by the District of Taylor up to 2:00 pm, local time Wednesday, September 17, 2014 at Council
More informationSNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM
DEKALB COUNTY HIGHWAY DEPARTMENT SNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM Sealed proposal for the furnishing and installing of snow plow, frame, hydraulic system,
More informationWHEEL LOADER WHEEL LOADER. ZW series Parallel linkage tool carrier version
ZW series Parallel linkage tool carrier version WHEEL LOADER WHEEL LOADER Model Code: ZW140PL / ZW150PL / ZW1PL Operating Weight: ZW140PL: 11 950-12 010 ZW150PL: 13 370-13 400 ZW1PL: 15 240-15 430 Bucket
More informationMantis Rerailer. General Specifications
General Specifications 1. Typical Operating Parameters 2. General 1.1 Operating temperatures will typically be between -4 F (-20 C) to 122 F (50 C). 1.2 Relative humidity ranges between 20% and 100%. 1.3
More informationTENDER 2019 OR 2020, ONE AND A HALF TON EXTENDED DOUBLE CAB/CHASSIS, 4X4, DUMP BODY TRUCK
Municipality of the County of Colchester Recreation Department 1 Church Street, Truro, NS B2N 3Z5 Telephone: (902) 897-3185 TENDER 2019 OR 2020, ONE AND A HALF TON EXTENDED DOUBLE CAB/CHASSIS, 4X4, DUMP
More informationSTATE OF MINNESOTA EQUIPMENT SPECIFICATION. SPECIFICATION: September 2012 Page 1 SINGLE AXLE CAB & CHASSIS
STATE OF MINNESOTA EQUIPMENT SPECIFICATION SPECIFICATION: 330-912 September 2012 Page 1 1.0 SCOPE SINGLE AXLE CAB & CHASSIS This unit shall be a currently advertised production model as modified per specifications
More informationBID REQUEST FOR Four (4) SCHOOL BUSES
College Community School District 401 76 th Ave. SW Cedar Rapids, Iowa 52404 BID REQUEST FOR Four (4) SCHOOL BUSES The College Community School District requests your bid on Four (4) 2018 78 passenger
More informationFLORIDA SHERIFFS ASSOCIATION & FLORIDA ASSOCIATION OF COUNTIES
FLORIDA SHERIFFS ASSOCIATION & FLORIDA ASSOCIATION OF COUNTIES Name of Dealership Type of Vehicle Zone REGENERATIVE AIR STREET SWEEPER (Specification #54) Base Unit Price Environmental Products Group,
More informationCity of Lewiston Finance Department Allen Ward, Purchasing Agent
City of Lewiston Finance Department Allen Ward, Purchasing Agent 2017-067 Two (2) 1 Ton 4X4 Dump Trucks with Plows for Public Works August 10, 2017 Sir/Madam: Sealed bids will be received in the office
More informationZip's Truck Equipment. 316 W. Milwaukee Street New Hampton, Iowa Phone: Fax: Visual Inspection.
Zip's Truck Equipment 316 W. Milwaukee Street New Hampton, Iowa 50659 Phone: 641-394-3166 Fax: 641-394-4044 Visual Inspection Page: 1 of 6 Customer: Address: Division: Phone: null Reference #: 2NPRLZ9X37M730087
More informationRequest for New Heavy Duty 3/4 ton Pickup Truck for Lee County Emergency Management
General: The attached specification is to aid in the purchase of an efficient and dependable 4-wheel drive pickup truck for the Office of Lee County Emergency Management. Bids must be submitted to Lee
More information534E WHEEL LOADER. Bucket Capacity 2.6 m 3 to 5.7 m 3 (3.4 yd 3 to 7.5 yd 3 ) Net Horsepower 169 kw (227 hp) Operating Weight kg (45,917 lb)
534E WHEEL LOADER Net Horsepower 169 kw (227 hp) Capacity 2.6 m 3 to 5.7 m 3 (3.4 yd 3 to 7.5 yd 3 ) Operating Weight 20828 kg (45,917 lb) The best in the business for productivi features and a wide choice
More informationMB3 Chassis with Front Mount Plow
MB3 Chassis with Front Mount Plow Reference Only. Shown with optional 24 Ft folding plow Reference Only. Shown with optional 24 Ft flared plow Chassis with four wheel Tru-Trac 4 x 4 drive. 164-inch wheel
More informationMulti-Service Vehicle Engine Specifications
This specification describes a high performance, articulated side walk tractor that shall support a variety of attachments. The versatility is required to allow operation in all four seasons of the year.
More informationLX80. Note: General purpose bucket with bolt on cutting edges. I J K. Unit : mm
S P E C I F I C A T I O N S LX80 W H E E L L O A D E R n Engine Rated Power : 80.9 kw (110 PS) n Operating Weight : Canopy / (Rops / Fops) Cab 8 120 kg / 8 610 kg n Backhoe Bucket : ISO Heaped - 1.9 40
More informationBarrow County Board of Education 179 W. Athens Street Winder, Georgia 30680
Barrow County Board of Education 179 W. Athens Street Winder, Georgia 30680 Judy Roberts Telephone: 770-867-4527 x100214 Business Services Fax: 770-867-4540 E-Mail: jroberts@barrow.k12.ga.us Barrow County
More informationWarranty - Standard Equipment & Specs
Warranty - Standard Equipment & Specs Warranty Basic Distance Unlimited miles Months 24 months Powertrain Distance Unlimited miles Months 24 months Corrosion Perforation Distance Unlimited miles Months
More informationAn ISO 9001:2000 Certified Company Autocar MY x DOT/EPA Compliant Terminal Tractor Standard Specifications
An ISO 9001:2000 Certified Company Autocar MY 2015 4x2 2013 DOT/EPA Compliant Terminal Tractor Standard Specifications Engine and Equipment Standard Optional Engine model Exhaust Air cleaner Radiator Fan
More informationINVITATION FOR BID Bid # 2013-RD102. Tandem Axle Dump Truck
INVITATION FOR BID Bid # 2013-RD102 Tandem Axle Dump Truck TECHNICAL SPECIFICATIONS Bid # 2013-RD102 Tandem Axle Dump Truck List Model Bid: MINIMUM SPECIFICATIONS EXCEPTIONS 1. TYPE a. Tandem Axle Truck-Current
More informationCity of Glasgow Department of Public Works Purchase of (1) 2013 White Rear Load Garbage Truck
City of Glasgow Department of Public Works Purchase of (1) 2013 White Rear Load Garbage Truck To: All Interested Bidders Subject: 2013 (1) White Rear Load Garbage Truck Attached are specifications for
More informationRequest For Bids. Sewer Cleaning Truck
Release: Thursday 22 September 2006 Closes: Friday 6 October 2006 CITY OF BISHOP 377 West Line Street - Bishop, California 93514 Post Office Box 1236 - Bishop, California 93515 760-873-8458 publicworks@ca-bishop.us
More informationIC-40-2C. Tech Spec. Industrial Crane. Four-wheel drive for tough applications. View thousands of Crane Specifications on FreeCraneSpecs.
Tech Spec Industrial Crane Four-wheel drive for tough applications Rated Capacity Limiter... Standard Capacity on Outriggers... 9,000 lbs Pick and Carry Capacity... up to 7,200 lbs Height... 6 8 Width...
More informationFour Wheel Drive Commercial Vehicles PCID NO COMMONWEALTH OF PENNSYLVANIA PENNSYLVANIA COMMERCIAL ITEM DESCRIPTION (PCID)
COMMONWEALTH OF PENNSYLVANIA PENNSYLVANIA COMMERCIAL ITEM DESCRIPTION (PCID) Four Wheel Drive Commercial Vehicles (Supersedes PCID 1105 eff. 19 September 19, 2012) PCID NO. 1105 Eff, August 12, 2013 1.
More informationMunicipality of the District of West Hants Request for Proposal (RFP) PW Supply of one (1) new ½ Ton 4x4 Truck
1.0 INSTRUCTIONS TO BIDDERS 1.1 Complete the Bid Sheet and attach other required information and send in a sealed envelope by mail or delivery to; To: Municipality of the District of West Hants RFP # PW
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on five trucks for the Public Works Department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on five trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours of
More informationAPPENDIX A TECHNCIAL SPECIFICATIONS
1. SCOPE The purpose of this Invitation to Negotiate (the "ITN") is to solicit pricing and select a vendor for the purchase of four (4) five ton 6X4, 14 to 16 cubic yard dump trucks, all new current model
More informationTENDER 2018 OR 2019, ONE AND A HALF TON CAB/CHASSIS, 4X4, DUMP BODY TRUCK
Municipality of the County of Colchester Public Works Department 1 Church Street, Truro, NS B2N 3Z5 Telephone: (902) 897-3175 TENDER 2018 OR 2019, ONE AND A HALF TON CAB/CHASSIS, 4X4, DUMP BODY TRUCK Sealed
More informationStandard features. Standard features of the Unimog U500 NA 2005 model
of the Unimog U500 NA 2005 model Engine: - MB 906 diesel engine; 260 hp at 2,200 rpm, torque 700 ft-lbs, max. rpm: 2,500 - Mercedes-Benz 6-cylinder diesel engine water cooled, turbo charger and intercooler
More informationDump Bodies Version of Excel used: CONTRACTOR BODY Warranty
Dump Bodies Contract end Date 09-30-18 Vendor Name: Contact Person: Street Address: P.O. Box: City, State, Zip Phone #: Toll Free #: Fax #: Email Address: Website: ABM Equipment & Supply, LLC. Sam Fahey
More informationSTATE OF MINNESOTA PRICING PAGE - FIXED PRICE (Typed Responses Required)
SEQ # 725-417 Price quote for: (Typed Responses Required) MUNICIPAL UTILITY TRACTOR 1 of 10 Vendor Name: Contact Person: Scott Reierson Street Address: 333 2nd Street NE P.O. Box: City, State, Zip Hopkins,
More informationSTATE OF MINNESOTA. 5.0 DUMP BODY SCOTT ALUMINUM Make. LANDSCAPER BODY Warranty. 1 YEAR BODY, DEALER PRICE LIST Date & I.D.
Vendor Name: ABM EQUIPMENT & SUPPLY, LLC. PRICING PAGE Contact Person: RON ZIMMER Street Address: 333 2ND STREET NE P.O. Box: City, State, Zip HOPKINS, MN 55343 Phone #: 952-938-5451 Toll Free #: 800-229-5451
More informationSTATE OF MINNESOTA PRICING Page % DISCOUNT
TRAILERS: DUMP BODY, LOWBOYS, FLATBED, TAG, SLIDE AXLE, UTILITY, GOOSENECK, ENCLOSED, ETC. Vendor Name: Truck Utilities Inc Contact Person: Paul Warner Street Address: 2370 English Street P.O. Box: City,
More informationTHREE (3) NEW 2018 SIX WHEEL DRIVE MOTOR GRADER WITH LIFT GROUP, REAR-RIPPER/SCARIFIER, AND SNOW WING.
Call for Bids Notice is hereby given that sealed bids will be received by the Board of Mountrail County Commissioners for the purchase of THREE (3) NEW 2018 SIX WHEEL DRIVE MOTOR GRADER WITH LIFT GROUP,
More informationIC-35-D. Engineering Spec. Page 1 of 8 Date: June 2006
Engineering Spec IC-35-D Page 1 of 8 Replaces: Form HD14D Dated: May 24 BMC s IC-35-2D is a Self-Propelled Industrial Crane designed for in-plant lifting and material handling applications. It has special
More information534E LA LANDFILL COMPACTOR. Operating Weight - w/ blade kg (50,485 lb) - w/ bucket kg (53,351 lb) Net Horsepower 169 kw (227 hp)
534E LA LANDFILL COMPACTOR Net Horsepower 169 kw (227 hp) Compaction ratio 1 : 3.5 Operating Weight - w/ blade 22 900 kg (50,485 lb) - w/ bucket 24 200 kg (53,351 lb) The best in the business for productivity
More informationTMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom
features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17
More informationPOWERTRAIN. NOTE: Travel speeds at 2334 engine rpm with 19.5L x 24 rear tires. Speeds decrease with 17.5L x 24 rear tires.
580L Series 2 Loader/Backhoe ENGINE Model... Case 4-390 diesel Type... 4-stroke, naturally aspirated Cylinders... 4 Bore/Stroke... 4.02 x 4.72 (102 x 120 mm) Displacement... 239 in 3 (3.9 L) Fuel injection...
More informationJuly 9, Re: Tender 4 X 4 Regular Cab ¾ Ton Work Trucks. Dear Sir:
July 9, 2015 Re: Tender 4 X 4 Regular Cab ¾ Ton Work Trucks. Dear Sir: We are re-tendering for two new 2015 or current model year regular cab, ¾ ton work trucks for the Operational Services Department
More informationZip's Truck Equipment. 316 W. Milwaukee Street New Hampton, Iowa Phone: Fax: Visual Inspection.
Zip's Truck Equipment 316 W. Milwaukee Street New Hampton, Iowa 50659 Phone: 641-394-3166 Fax: 641-394-4044 Visual Inspection Page: 1 of 6 Customer: Division: null Address: Phone: Reference #: 1GBKC34J9VJ103606
More informationSTATE OF MINNESOTA PRICING PAGE - FIXED PRICE (Typed Responses Required)
1 of 7 Price quote for: MUNICIPAL UTILITY TRACTOR Vendor Name: ABM Equipment & Supply, LLC. Contact Person: Scott Reierson Street Address: 333 2nd Street NE P.O. Box: City, State, Zip Hopkins, MN 55343
More informationWarranty - Standard Equipment & Specs
Warranty - Standard Equipment & Specs Warranty Basic Distance Unlimited miles Months 24 months Powertrain Distance Unlimited miles Months 24 months Corrosion Perforation Distance Unlimited miles Months
More informationADDENDUM 2. The following clarifications, changes, additions, and/or deletions are hereby made to the RFB:
Date: January 2, 2018 ADDENDUM 2 RFB No: FS-07-18 / Haul Truck Bid Date: January 11, 2018/2:00 PM Local Time The following clarifications, changes, additions, and/or deletions are hereby made to the RFB:
More informationS P E C I F I C A T I O N S
S P E C I F I C A T I O N S LX50 W H E E L L O A D E R Engine Rated Power : 44.1 kw (60 PS) Operating Weight : Canopy / Cab 4 695 kg (10 350 lb) / 4 845 kg (10 680 lb) Backhoe Bucket : ISO Heaped 0.6 m
More informationIC-400-3A. Tech Spec. Industrial Crane. 25-Ton Max. Capacity (22,700 kg) Manufacturing Corp. Rated Capacity Limiter... Standard
Tech Spec IC-400-3A Industrial Crane 25-Ton Max. Capacity (22,700 kg) Rated Capacity Limiter... Standard Capacity on Outriggers... 50,000 lbs (22,700 kg) Pick and Carry Capacity... up to 24,400 lbs (11,000
More informationABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits
Air Brake Systems ABS Components Air Compressors Air Dryers & Cartridges Air Tanks Air Valves Brass Fittings Composite Fittings Coiled Air Hoses Glad Hands Nylon Tubing Rubber Hose Tire Valves Brake &
More informationMUNICIPAL SNOW & ICE CONTROL EQUIPMENT NOTHING WORKS LIKE A DOGG
MUNICIPAL SNOW & ICE CONTROL EQUIPMENT NOTHING WORKS LIKE A DOGG Our History 1946 Buyers Products Company founded by Sam Ruven and Bessie Kleinman as a distributor of driveline components. Buyers continued
More informationCat BACKHOE LOADER. breakout forces and aggressiveness in hard bank applications. to the operator while roading.
Cat F BACKHOE LOADER The Cat F Backhoe Loader delivers performance, increased fuel efficiency, superior hydraulic system and an all new operator station. The F features the following: Ergonomic Operator
More informationMSV. Innovating for you
MSV Innovating for you Innovating for you - A new generation of multi-service vehicles CAB SAFETY Operators enclosure is ROPS certified to SAE J 1040C and ISO 3471 at 12,000 lbs. IN CONTROL Sure Grip Controls
More informationAs a safety precaution, remove keys from the ignition while working under or around the vehicle.
CAB AND CHASSIS As a safety precaution, remove keys from the ignition while working under or around the vehicle. 1. Approach Check the overall appearance of vehicle stance (not leaning). Check for signs
More information22956 Hwy 61 PO Box 295 Morley, MO Phone: Fax: MODOT 04/17/17
-GENERAL SERVICES FLEET SECTION TP260000 Viking TP 26, 26' Tow Plow with swivel tongue, (1) 12' moldboard and (1) 14', base angles drilled for carbide edges (no cutting edges included), 10 gauge steel
More informationPOWER UNIT: (Deere 4045T Tier 4 74HP) In-Line 4 cylinder, 4-cycle, Turbo Diesel. 74 HP (55 KW) Intermittent at 2400 RPM.
GENERAL: This specification describes a self-contained engine-driven vacuum leaf collecting machine. The leaf collector is trailer mounted, designed for one-person operation, and capable of picking up
More informationInline 6 series turbocharger with exhaust gas recirculation (EGR) and selective catalytic reduction (SCR) Valves per Cylinder 4
SPECIFICATIONS Engine Manufacturer and Model John Deere PowerTech PSS 6090 Non-Road Emission Standards EPA Final Tier 4/EU Stage IV Configuration Inline 6 series turbocharger with exhaust gas recirculation
More informationTechnical Specifications
140 Motor Grader Technical Specifications Engine Engine Model Cat C9.3 Net Power ISO 9249/SAE J1349 186 kw 250 hp Net Power EEC 80/1269 186 kw 250 hp Net Power All-Wheel Drive (AWD) 201 kw 270 hp VHP Plus
More informationINFEED HOPPER COMPONENTS. Parts may not be exactly as shown. Bandit. Copyright 1/12
INFEED HOPPER COMPONENTS 80 INFEED HOPPER COMPONENTS 1. 626-200019 Folding Pan for Infeed Hopper 2 a. 900-4901-83 Folding Pan Spring Lock & Trap Door Lock b. 900-7900-93 Black Rubber Cap (Not Shown) 3
More informationHIGH-CAPACITY IC PNEUMATIC
HIGH-CAPACITY IC PNEUMATIC 22000 72000 LBS. REACH NEW S SPECIFICATIONS THD2200-7200 CLASS 5 INTERNAL COMBUSTION ENGINE PNEUMATIC TIRE ToyotaForklift.com HIGH-CAPACITY IC PNEUMATIC CAPACITY 22000 72000
More information