Super Mist Separator. Note) Rated flow (l/min (ANR)) 1 8, , , , , 1

Transcription

1 Super ist Separator Series AE an separate and adsorb aerosol state fine oil particles in compressed air and change the oil lubricating compressed air to oilless air or equivalent. Use this product for filtration of compressed air requiring higher clean air for painting lines, compressed air for clean rooms and/or equipment where oils must be avoided. ndicates the filter element life by a color change. Accordingly, the replacement time can be judged visually. (A red color spot indicates the replacement time.) aution y all means the A series should be used as a pre-filter. odular connection is possible with AE0 to 0. (or details, refer to page 1.) odel odel AE0 AE20 AE30 AE40 AE0 AE0 ote) ated flow (l/min (A)) ass (kg) 1 8, , , , , 1 AE ote) ax. flow at 0.7 a. ax. flow varies depending on the operating pressure. efer to low haracteristics (page 47) and aximum Air low (page 47). Specifications luid ax. operating pressure in. operating pressure roof pressure Ambient and fluid temperature ominal filtration rating leanliness at outlet Oil mist density at outlet Element life Accessory Applicable model racket assembly (with 2 mounting screws) ompressed air 1.0 a 0.0 a 1. a to μm (iltration efficiency:.%) ess than 0 particles of 0.3 μm or larger per cubic foot [ess than 3 particles per liters (A)] ax mg/m 3 (A) ( ppm) Element color indicator (eplace the element when a red color spot occurred on the surface.) AE0 AE20 AE30 AE40 AE0 AE0 1, , 2 AE80 A-1 A-2 A-3 A-4 A- 7 AE0 to 30 AE40/0 aution e sure to read this before handling. efer to back pages 1 and 2 for Safety nstructions, recautions for Handling neumatic evices (-03-E3A) for ommon recautions, and back pages 3 through to 7 for Specific roduct recautions. AE AE0/80 ade to Order (or details, refer to page 7.) 44

2 Series AE How to Order AE0 to 0 AE 0 ody size Thread type Type il c 1 T 1 onforms to SO Option escription il ubber material: luororubber H or medium air pressure (1. a) - reversal direction V egreasing wash, 3 white vaseline 3 Only body/housing is degreasing washed. Accessory escription il racket 2 2 racket is included, (but not assembled) Size 1/8 1/4 3/8 1/2 3/4 1 Applicable body size Options : ubber material: luororubber luororubber is used for the parts such as O-ring and gasket. H: or medium air pressure (1. a) an be used up to 1. a at maximum. : - reversal direction Air flow in the separator is changed to right to left. (Air flow direction of the standard: eft to right.) V: egreasing wash, white vaseline ody/housing is degreasing washed. The lubrication grease for O-ring and gasket is changed to white vaseline. 4

3 Super ist Separator Series AE How to Order AE0/80 AE 0 ody size 0 80 Thread type Type il c T ade to Order ( How to Order and the applicable models are different from those shown on this page. e sure to refer to the page ade to Order.) il X12 Option escription il - reversal direction escription White vaseline specifications age for details.70 Size Applicable body size 0 80 Accessory escription il racket racket is included, (but not assembled). ote) efer to How to Order owl Assembly on page 3. 4

4 Series AE low haracteristics (Element initial condition) ote) ompressed air over max. flow line in the table below may not meet the specifications of the product. t may cause damage to the element. AE0 AE40 AE0 Air flow rate (l/min (A)) Air flow rate (l/min (A)) Air flow rate (l/min (A)) AE20 AE0 AE80 Air flow rate (l/min (A)) Air flow rate (l/min (A)) Air flow rate (m 3 /min (A)) AE30 aximum Air low Air flow rate (l/min (A)) odel Selection Select a model in accordance with the following procedure taking the inlet pressure and the max. air flow rate into consideration. (Example) nlet pressure: 0. a ax. air flow rate: m 3 /min (A) 1. Obtain the interecting point A of inlet pressure and max. air flow rate in the graph. 2. The AE0 is obtained when the max. flow line is above the intersecting point A in the graph. ax. air flow rate (m 3 /min (A)) 47 ote) ake sure to select a model that has the max. flow line above the obtained intersecting point. With a model that has the max. flow line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. nlet pressure (a)

5 Super ist Separator Series AE onstruction AE0 to 0 AE0/80 q r e w omponent arts o. escription aterial ote ody Housing Sight glass Aluminum die-casted Aluminum die-casted Tempered glass hrome treated Epoxy coating on inner surface The AE80 is aluminum casted. eplacement arts o. 4 escription Element assembly aterial lass fiber, others Applicable model Except option or option AE0 AE-E0 AE-E0- AE20 AE-E20 AE-E20- AE30 AE-E30 AE-E30- odel AE40 AE-E40 AE-E40- Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Element assemblies for ade to Order (X12, X20) are same as those for standard (see the above table). ote) efer to How to Order owl Assembly on page 3. ote) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. efer to dimensions on pages 4 through to 1 for details. AE0 AE-E0 AE-E0- AE0 AE-E0 AE80 AE-E80 48

6 O A S T E racket (Accessory) øw J V U K aintenance space AE0 to 30 (mm) AE0 AE20 AE30 A odel racket related dimensions /8, 1/4 1/4, 3/8 3/8, 1/ E J K 8 8 U 7 V W 12 O S 4. T imensions 4 Series AE

7 E T racket (Accessory) U øw V J K H aintenance space A O AE40/0 AE40 AE0 A odel racket related dimensions /2, 3/4 3/4, E H J K U V W O T (mm) imensions Super ist Separator Series AE 0

8 Series AE imensions AE0/80 racket (Accessory) 2 x port size aintenance space odel A AE0 AE80 1, , E H J K racket related dimensions O (mm) S 4. 1