Coupling Company. Catalog Version El Camino Ave. Corona, CA Phone: (951) Fax: (951)

Transcription

1 Coupling Company Catalog 2014 Version El Camino Ave. Corona, CA Phone: (951) Fax: (951) I

2 NO HUB Table of Contents No hub Couplings List Price 1 No hub Couplings Submi al 2 No hub Couplings Installa on Instruc ons 3 HUSKY SD 4000 Husky SD 4000 List Price 4 Husky SD 4000 Couplings Submi al 5 Husky SD 4000 Couplings Submi al (12 & 15 ) 6 Husky SD 4000 Couplings Reducer Submi al 7 Husky SD 4000 Couplings Transi on Submi al 8 Husky SD 4000 Couplings Installa on Sugges ons 9 HUSKY HD 2000 Husky HD 2000 List Prices 10 Husky HD 2000 Submi al 11 Husky HD 2000 Reducer 12 Husky HD 2000 Transi on Submi al 13 Husky HD 2000 Installa on Sugges ons 14 SERVICE WEIGHT GASKET Service Weight Gasket List Prices 15 EZ Tight Compression Gasket Submi al 16 Ty Seal Gasket Submi al 17 SPECIALTY COUPLINGS RIGID QUIK Cremco Specialty Transi on Couplings List Price 18 Cremco Transi on Couplings Submi al 20 Anaco Cap List Prices 21 Rigid Quik List Prices 22 Rigid Quik Submi al 23 II

3 anaco NO HUB COUPLINGS List Prices NH-711NAT July 1, 2011 ANACO Part # Size List Price Carton Quantity Weight Per carton /2" $ lbs " $ lbs " $ lbs " $ lbs " $ lbs " $ lbs " $ lbs " $ lbs. HEAVY DUTY NO-HUB COUPLINGS (Special Multiplier) " $ " $ REDUCING COUPLINGS x1-1/2 reducing $ x2 reducing $ x3 reducing $ x2 reducing $ We reserve the right to withdraw this sheet without notice and price in effect at time of shipment will apply. Possession of this list price sheet shall not be construed as an offer to sell. Freight: Prepaid on all orders of 750 or more 1001 El Camino Ave. Corona, CA Phone: (951) Fax: (951)

4 CISPI 310 NO HUB COUPLINGS Submi al anaco No Hub Couplings meet CISPI 310 and ASTM C Couplings consist of a stainless steel shield, clamp assembly and a gasket manufactured from a properly vulcanized virgin compound in which the primary elastomer is polychloroprene (neoprene) conforming to ASTM C 564. Compliant to BAA, TAA, ARRA, NAFTA & NSF. The couplings is used to join hubless cast iron pipe and fi ngs made to CISPI 301 and/ or ASTM A 888. Coupling size range from 1 ½ through 15 diameters. The stainless steel shield and clamp assemblies are corrosion resistant. Material Specification Clamp: Type 301 AISI stainless steel Screw: Type 305 AISI stainless steel 5/16 hex head for 1 ½ - 10, 3/8 for 12 & 15 Shield: Type 301 AISI Stainless steel corrugated. Shield thickness Housing: Type 301 AISI stainless steel Gasket Test Test Physical Tests Min. Or Max Requirements ASTM Method Tensile strength 1500 psi min. D412 Elongation 250 min. D412 Durometer [Shore A] 70 ± 76 F ± 5 F D2240 Accelerated Aging 15% maximum tensile and 20% maximum elongation deterioration, 10 points maximum increase in hardness, all determinations after oven aging for 96 hours at 158 F D573 Compression Set 25% maximum after 22 hours at 158 F D395 Method B Oil Immersion 80% maximum volume change after immersion in IRM 903 D471 for 70 hours at 212 F Ozone Cracking No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5ppm ozone concentration at 100 F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface. D1149 Water Resistance 150 lbs. minimum per inch of thickness D624 Water Absorption 20% maximum by weight after 7 days at 158 F D El Camino Ave. Corona, CA Phone: (951) Fax: (951)

5 NO HUB COUPLINGS Installa on Sugges ons Size Width No. of Straps Torque 1 ½ & & & Size 1-1/2" thru4 TWO BANDS Figure 1 Size 5, 6 8 thru 10 FOUR BANDS Figure 2 Size 12 And 15 SIX BANDS Figure3 Installa on Instruc ons 1) A er making the field cuts square and placing the ends of the pipes against the center stop of the gasket, slide the clamp assembly into posi on centered over the gasket. 2) Using a torque wrench, ghten stainless steel screws alternately to 60 inch pounds torque for 1½ to 10" and 80 inch pounds torque for 12" & 15". 3) For 5" to 10" couplings, ghten inner bands first, then ghten outer bands. 4) For 12" & 15" couplings, ghten inner bands, center bands and outer bands. When min max condi ons exist, ghten each band star ng on the smaller side: 3,2,1and 3,2,1 again. Then torque the maximum side: 4, 5, 6 and 4, 5, 6 again. Finally, torque 2,1on the minimum side and 4, 5, 6 on the maximum side. (See Figure 3 above) Bracing Horizontal pipe and fittings five inches and larger must be suitably braced to prevent horizontal movement. This must be done at every branch opening or change of direction by the use of braces, blocks, rodding or other suitable method, to prevent movement or joint separation. (Chapter IV, Handbook Cast Iron Soil Pipe Institute) 3

6 anaco HUSKY SD 4000 List Prices SD 711NAT July 1, 2011 Part Number Coupling Size Carton Quantity Carton Weight List Price ½" " " " " " " " " " Reducing Couplings Coupling Size Carton Quantity Carton Weight List Price x 1½ x x x Transition Couplings Coupling Size Carton Quantity Carton Weight List Price x 1½ x Terms: 2% 10th prox., net thereafter. Full freight is allowed on all orders of $2500 or 600 or more pieces. Prices subject to change without notice. Return goods restocking charge of 25% subject to factory charge authorization. Orders will be subject to a 10% premium on broken case quantities only El Camino Ave. Corona, CA Phone: (951) Fax: (951)

7 HUSKY SERIES 4000 COUPLING Product Informa on Submi al Cer fica ons & Standards Size Width No. of Straps Torque 1 ½ Meets ASTM C 1540 Meets ASTM C 564 Meets F 1680 Class 1 Meets CSA B 602 Iapmo File & & SIZES 1½ thru 4 SIZES 5,6,8 & 10 Material Specifica ons Clamp: Type 304 AISI Stainless steel Screw: Type 305 AISI stainless steel 3/8 Shield: Type 304 AISI stainless steel, corrugated. Shield thickness Gasket: The gasket shall be manufactured from a properly vulcanized virgin compound in which the primary elastomer is polychloroprene (neoprene) conforming to ASTM C 564. Oil Immersion test: 80% max. Volume Change after immersion in ASTM oil no. 3 for 70 hours at 212 F. The Husky SD 4000 Coupling has been engineered by anaco to provide a heavy duty, all stainless steel coupling, balancing the desire for a more rigid joint with the need to provide a superior posi ve seal, which can accommodate possible dispari es in the ma ng of No Hub pipe and fi ngs. This has been accomplished by manufacturing our coupling with a super duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. The addi onal sealing clamps when torqued to 80 inch pounds, offer two salient performance related features. First, the overall dimensional thickness of the clamp and shield, in conjunc on with the addi onal width of the coupling, result in a more uniformly rigid joint, with the load being supported at both the outer edge of the coupling and the centerline of the joint. Second, the addi onal sealing clamps yield increased surface bearing contact between the coupling and the pipe or fi ngs, thereby inhibi ng joint movement at higher internal pressures not commonly associated with a DWV system. The 1½" through 4" diameter couplings consist of a 3" wide corrugated 304 stainless steel shield in conjunc on with four (4) stainless steel clamps mounted in a series, secured in place by means of affixed and "floa ng" eyelet to allow the clamp "travel" during ghtening. The 5" through 10" diameter couplings consist of a 4" wide corrugated 304 stainless steel shield in conjunc on with six (6) stainless steel clamps mounted in a series, secured in place by means of affixed and "floa ng" eyelet to allow the clamp "travel" during ghtening. All SD 4000 Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds to accommodate the 305 stainless steel 3/8" Hex Head screw. 5

8 HUSKY SERIES 4000 COUPLING Product Informa on Submi al Size Width No. of Straps Torque 12 & Cer fica ons & Standards Meets ASTM C 1540 Meets ASTM C 564 Iapmo File 6726 SIZES 12 & 15 Material Specifica ons Clamp: Type 304 AISI Stainless steel Screw: Type 305 AISI stainless steel 3/8 Shield: Gasket: Type 304 AISI stainless steel, corrugated. The gasket shall be manufactured from a properly vulcanized virgin compound in which the primary elastomer is polychloroprene (neoprene) conforming to ASTM C 564. Oil Immersion test: 80% max. Volume Change after immersion in ASTM oil no. 3 for 70 hours at 212 F. The Husky SD 4000 Coupling has been engineered by anaco to provide a heavy duty, all stainless steel coupling, balancing the desire for a more rigid joint with the need to provide a superior posi ve seal, which can accommodate possible dispari es in the ma ng of No Hub pipe and fi ngs. This has been accomplished by manufacturing our coupling with a super duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. The addi onal sealing clamps when torqued to 80 inch pounds, offer two salient performance related features. First, the overall dimensional thickness of the clamp and shield, in conjunc on with the addi onal width of the coupling, result in a more uniformly rigid joint, with the load being supported at both the outer edge of the coupling and the centerline of the joint. Second, the addi onal sealing clamps yield increased surface bearing contact between the coupling and the pipe or fi ngs, thereby inhibi ng joint movement at higher internal pressures not commonly associated with a DWV system. The 12 & 15 diameter couplings consist of a 5½ wide corrugated 304 stainless steel shield in conjunc on with six (6) stainless steel clamps mounted in a series, secured in place by means of affixed and floa ng eyelet to allow the clamp travel during ghtening. All SD 4000 Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds to accommodate the 305 stainless steel 3/8" Hex Head screw. 6

9 HUSKY 4000 REDUCER COUPLING Product Informa on Submi al Test Physical Tests Min. or Max Requirements ASTM Method Tensile Strength 1500 psi min. D 412 Elongation 250 min. D 412 Durometer [Shore A] 70 +/- 76 F +/- 5 F. D 2240 Accelerated Aging 15% maximum tensile and 20% maximum elongation deterioration, 10 points maximum increase in hardness, all determination after oven aging for 96 hours at 158 F D 573 Compression Set 25% maximum after 22 hours at 158 F D 395 method B Oil Immersion 80% maximum volume change after immersion in IRM 903 for 70 hours at 212 F Ozone Cracking No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5ppm ozone concentration at 100 F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface. D471 D 1149 Tear Resistance 150Lbs. Minimum per inch of thickness D 624 Water Absorption 20% maximum by weight after 7 days at 158 F D 471 Clamp: Type 304 AISI stainless steel. Materials Screw: Type 305 AISI stainless steel 3/8 Shield: Type 304 AISI stainless steel, corrugated. Shield thickness.015 Gasket: The gasket shall be manufactured from a properly vulcanized virgin compound in which the primary elastomer is polychloroprene (neoprene) conforming to ASTM C 564 Application Data Model Size x1½ x x3 Certifications & Standards Meets ASTM C 1540 Meets ASTM C 564 Iapmo File x2 The HUSKY SD 4000 Coupling has been engineered by anaco to provide a heavy duty, all stainless steel coupling, balancing the desire for a more rigid joint with the need to provide a superior posi ve seal, which can accommodate possible dispari es in ma ng of No Hub pipe and fi ngs. This has been accomplished by manufacturing our coupling with a super duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. All SD 4000 Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds to accommodate the 305 stainless steel 3/8 Hex Head screw. 7

10 Test HUSKY COUPLING FOR HUBLESS TO COPPER JOINTS Product Informa on Submi al Gasket Physical Test Min. or Max Requirements ASTM Method Tensile Strength 1500 psi min. D 412 Elongation 250 min. D 412 Durometer [Shore A] F ± 5 F. D 2240 Accelerated Aging 15% max. tensile and 20% max. elongation deterioration, 10 points max. increase in hardness, all determinations after oven aging for 96 hours at 158 F D 573 Compression Set 15% max. after 22 hours at 158 F D 395 method B Oil Immersion Ozone Cracking 80% max. volume change after immersion in ASTM oil no. 3 for 70 hours at 212 F D471 No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5ppm ozone concentration at 100 F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface. D 1149 Tear Resistance Die C; 150 lbs., min. per inch of thickness D 624 Water Absorption 20% max by weight after 7 days at 158 F D 471 Clamp: Screw: Type 304 AISI stainless steel. Materials Type 305 AISI stainless steel 3/8 hex head/shoulder Shield: Type 304 AISI stainless steel, corrugated. Shield thickness.016 Gasket: The gasket shall be fabricated from a compound containing high quality neoprene as the sole elastomer. ASTM C 564. Application Data Model Dim A Dim B CI CI ASTM C 1277 ASTM C ½ Copper 2 Copper The HUSKY SD 4101 & 4102 is a heavy duty all stainless steel transi on coupling to connect cast iron Hubless pipe and fi ngs to Copper pipe. This has been accomplished by manufacturing our coupling with a heavy duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. The couplings consist of a 3 wide corrugated 304 stainless steel shield in conjunc on with four stainless steel clamps mounted in a series, secured in place by means of a fixed and floa ng eyelet to allow the clamp travel during ghtening Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds, to accommodate the stainless steel 3/8 Hex Head/Shoulder screw. Meets ASTM C 1460 standard. 8

11 INSTALLATION SUGGESTIONS FOR THE ANACO SD 4000 NO HUB COUPLING Purpose T hese sugges ons provide guidelines for the use of anaco HUSKY SD 4000 Coupling for joining No Hub pipe and fi ng in accordance with accepted industry standards and prac ces. All construc on projects involve many variables. Governing codes, engineering criteria, and the conven ons of the plumbing trade necessitate that judgment decisions must be a combina on of design and "on the job" considera ons. The following sugges ons for joining No Hub pipe and fi ngs with the anaco HUSKY coupling are not defini ve but it is hoped that they will be helpful. Installa on Instruc ons A properly calibrated torque wrench set at 80 inch pounds should always be used when installing HUSKY couplings. When power tools are used to install HUSKY couplings they should be adjusted or calibrated to torque only to 80 inch pounds. 1. In order to provide a sound joint with field cut lengths of pipe, he ends should be cut square. Place the Neoprene gasket on the end of one pipe and the stainless steel clamp assembly on the other end of the other pipe or fi ng to be joined. 2. Firmly seat both ends of the pipe/fi ngs against the internally molded shoulder in the center of the gasket. 3. Slide the clamp assembly into posi on centered over the gasket. 4. HUSKY couplings 1 ½, 2, 3 and 4 are three inches wide and have four sealing bands. Tighten bands to 80 inch pounds in the following sequence. Star ng on the side of the joint with the smaller diameter (see diagram A ) torque as follows: 2,1 2,1 3,4 2,1 3,4. 5. HUSKY couplings 5, 6, 8 and 10 are four inches wide and have six sealing bands. Tighten bands to 80 inch pounds in the following sequence. Star ng on the side of the joint with the small diameter, (see diagram B) torque as follows: 3,2,1 3,2,1, 4,5,6 4,5,6 2,1 4,5,6. 6. Once the coupling is installed and torqued to 80 inch pounds in this torque pa ern it is no necessary to go back and re torque the couplings. ***HUSKY Technologies has inten onally color coated the HUSKY 304 Stainless Steel Shield. The Orange shield iden fies this product as genuine anaco HUSKY Heavy Duty Coupling. Husky s performance, including its excep onal sealing ability, corrosion resistance, deflec on and rigidity has not been compromised in any way. Rev

12 HUSKY HD 2000 List Prices HD- 711NAT July 1, 2011 Part Number Coupling Size Carton Quantity Carton Weight List Price ½" " " " " " " " Reducing Couplings Coupling Size Carton Quantity Carton Weight List Price x1½ x x x Transition Couplings Coupling Size Carton Quantity Carton Weight List Price x 1½ x Terms: 2% 10th prox., net thereafter. Full freight is allowed on all orders of $2500 or 600 or more pieces. Prices subject to change without notice. Return goods restocking charge of 25% subject to factory charge authorization. Orders will be subject to a 10% premium on broken case quantities only El Camino Ave. Corona, CA Phone: (951) Fax: (951)

13 HUSKY SERIES 2000 COUPLING Product Informa on Submi al Cer fica ons & Standards Size Width No. of Straps Torque Meets ASTM C 1540 Meets ASTM C 564 Meets FM 1680 Class 1 Meets CSA B 602 Iapmo File ½ & & SIZES 1½ thru 4 SIZES 5,6,8 & 10 Material Specifica ons Clamp: Type 304 AISI Stainless steel Screw: Type 305 AISI stainless steel 5/16 Shield: Type 304 AISI stainless steel, corrugated. Shield thickness Gasket: The gasket shall be manufactured from a properly vulcanized virgin compound in which the primary elastomer is polychloroprene (neoprene) conforming to ASTM C 564. Oil Immersion test: 80% max. Volume Change after immersion in ASTM oil no. 3 for 70 hours at 212 F. The HUSKY HD 2000 Coupling has been engineered by anaco to provide a heavy duty, all stainless steel coupling, balancing the desire for a more rigid joint with the need to provide a superior posi ve seal, which can accommodate possible dispari es in the ma ng of No Hub pipe and fi ngs. This has been accomplished by manufacturing our coupling with a super duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. The addi onal sealing clamps when torqued to 80 inch pounds, offer two salient performance related features. First, the overall dimensional thickness of the clamp and shield, in conjunc on with the addi onal width of the coupling, result in a more uniformly rigid joint, with the load being supported at both the outer edge of the coupling and the centerline of the joint. Second, the addi onal sealing clamps yield increased surface bearing contact between the coupling and the pipe or fi ngs, thereby inhibi ng joint movement at higher internal pressures not commonly associated with a DWV system. The 1½" through 4" diameter couplings consist of a 3" wide corrugated 304 stainless steel shield in conjunc on with four (4) stainless steel clamps mounted in a series, secured in place by means of affixed and "floa ng" eyelet to allow the clamp "travel" during ghtening. The 5" through 10" diameter couplings consist of a 4" wide corrugated 304 stainless steel shield in conjunc on with six (6) stainless steel clamps mounted in a series, secured in place by means of affixed and "floa ng" eyelet to allow the clamp "travel" during ghtening. All HD 2000 Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds to accommodate the 305 stainless steel 3/8" Hex Head screw. 11

14 HUSKY 2000 REDUCER COUPLING Product Informa on Submi al Test Physical Tests Min. or Max Requirements ASTM Method Tensile Strength 1500 psi min. D 412 Elongation 250 min. D 412 Durometer [Shore A] 70 +/- 76 F +/- 5 F. D 2240 Accelerated Aging 15% maximum tensile and 20% maximum elongation deterioration, 10 points maximum increase in hardness, all determination after oven aging for 96 hours at 158 F D 573 Compression Set 25% maximum after 22 hours at 158 F D 395 method B Oil Immersion 80% maximum volume change after immersion in IRM 903 for 70 hours at 212 F Ozone Cracking No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5ppm ozone concentration at 100 F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface. D471 D 1149 Tear Resistance 150Lbs. Minimum per inch of thickness D 624 Water Absorption 20% maximum by weight after 7 days at 158 F D 471 Materials Clamp: Type 304 AISI stainless steel. Screw: Type 305 AISI stainless steel 5/16 Shield: Type 304 AISI stainless steel, corrugated. Shield thickness.010 Gasket: The gasket shall be manufactured from a properly vulcanized virgin compound in which the primary elastomer is polychloroprene (neoprene) conforming to ASTM C 564 Application Data Model Size x1½ x x3 Certifications & Standards Meets ASTM C 1540 Meets ASTM C 564 Iapmo File x2 The HUSKY HD 2000 Coupling has been engineered by anaco to provide a heavy duty, all stainless steel coupling, balancing the desire for a more rigid joint with the need to provide a superior posi ve seal, which can accommodate possible dispari es in ma ng of No Hub pipe and fi ngs. This has been accomplished by manufacturing our coupling with a super duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. All HD 2000 Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds to accommodate the 305 stainless steel 5/16 Hex Head screw. 12

15 Test HUSKY COUPLING FOR HUBLESS TO COPPER JOINTS Product Informa on Submi al Gasket Physical Test Min. or Max Requirements ASTM Method Tensile Strength 1500 psi min. D 412 Elongation 250 min. D 412 Durometer [Shore A] F ± 5 F. D 2240 Accelerated Aging 15% max. tensile and 20% max. elongation deterioration, 10 points max. increase in hardness, all determinations after oven aging for 96 hours at 158 F D 573 Compression Set 15% max. after 22 hours at 158 F D 395 method B Oil Immersion Ozone Cracking 80% max. volume change after immersion in ASTM oil no. 3 for 70 hours at 212 F D471 No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5ppm ozone concentration at 100 F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface. D 1149 Tear Resistance Die C; 150 lbs., min. per inch of thickness D 624 Water Absorption 20% max by weight after 7 days at 158 F D 471 Clamp: Screw: Materials Type 304 AISI stainless steel. Type 305 AISI stainless steel 5/16 hex head/shoulder Shield: Type 304 AISI stainless steel, corrugated. Shield thickness.010 Gasket: The gasket shall be fabricated from a compound containing high quality neoprene as the sole elastomer. ASTM C 564. Application Data Model Dim A Dim B CI CI ASTM C 1277 ASTM C ½ Copper 2 Copper The Husky HD 2101 & 2102 is a heavy duty all stainless steel transi on coupling to connect cast iron Hubless pipe and fi ngs to Copper pipe. This has been accomplished by manufacturing our coupling with a heavy duty corrugated shield of sufficient width to accommodate addi onal surface bearing sealing clamps. The couplings consist of a 3 wide corrugated 304 stainless steel shield in conjunc on with four stainless steel clamps mounted in a series, secured in place by means of a fixed and floa ng eyelet to allow the clamp travel during ghtening Couplings are designed to be installed with a pre set torque wrench calibrated at 80 inch pounds, to accommodate the stainless steel 5/16 Hex Head/Shoulder screw. Meets ASTM C 1460 standard. 13

16 INSTALLATION SUGGESTIONS FOR THE ANACO HD 2000 NO HUB COUPLING Purpose T hese sugges ons provide guidelines for the use of anaco HUSKY HD 2000 Coupling for joining No Hub pipe and fi ng in accordance with accepted industry standards and prac ces. All construc on projects involve many variables. Governing codes, engineering criteria, and the conven ons of the plumbing trade necessitate that judgment decisions must be a combina on of design and "on the job" considera ons. The following sugges ons for joining No Hub pipe and fi ngs with the anaco HUSKY coupling are not defini ve but it is hoped that they will be helpful. Installa on Instruc ons A properly calibrated torque wrench set at 80 inch pounds should always be used when installing HUSKY couplings. When power tools are used to install HUSKY couplings they should be adjusted or calibrated to torque only to 80 inch pounds. 1. In order to provide a sound joint with field cut lengths of pipe, he ends should be cut square. Place the Neoprene gasket on the end of one pipe and the stainless steel clamp assembly on the other end of the other pipe or fi ng to be joined. 2. Firmly seat both ends of the pipe/fi ngs against the internally molded shoulder in the center of the gasket. 3. Slide the clamp assembly into posi on centered over the gasket. 4. HUSKY couplings 1 ½, 2, 3 and 4 are three inches wide and have four sealing bands. Tighten bands to 80 inch pounds in the following sequence. Star ng on the side of the joint with the smaller diameter (see diagram A ) torque as follows: 2,1 2,1 3,4 2,1 3,4. 5. HUSKY couplings 5, 6, 8 and 10 are four inches wide and have six sealing bands. Tighten bands to 80 inch pounds in the following sequence. Star ng on the side of the joint with the small diameter, (see diagram B) torque as follows: 3,2,1 3,2,1, 4,5,6 4,5,6 2,1 4,5,6. 6. Once the coupling is installed and torqued to 80 inch pounds in this torque pa ern it is no necessary to go back and re torque the couplings. ***HUSKY Technologies has inten onally color coated the HUSKY 304 Stainless Steel Shield. The White shield iden fies this product as genuine anaco HUSKY Mid Range Coupling. Husky s performance, including its excep onal sealing ability, corrosion resistance, deflec on and rigidity has not been compromised in any way. Rev

17 anaco SERVICE WEIGHT GASKET List Prices SWG-711NAT July 1, 2011 ANACO Ty Seal Part # ANACO EZ Tite Part # Size List Price Carton Quantity Weight Per carton " $ lbs " $ lbs " $ lbs " $ lbs " $ lbs N/A 8" $ lbs N/A 10" $ lbs N/A 12" $ lbs N/A 15" $ lbs. We reserve the right to withdraw this sheet without notice and price in effect at time of shipment will apply. Possession of this list price sheet shall not be construed as an offer to sell. Freight: Prepaid on all orders of 750 pieces or more 1001 El Camino Ave. Corona, CA Phone: (951) Fax: (951)

18 EZ TIGHT COMPRESSION GASKET SUBMITTAL SV EZ TIGHT GASKETS Size Unit Carton Carton Bracing: Description: Ez-Tight is a one-piece compression gasket. It is used for joining hub and spigot cast iron soil pipe and fittings made according to ASTM A 74. Gasket Specification: Ez-Tight gaskets conform strictly to ASTM Standard C 564, latest issue. Joint Characteristics: Gasket joints will not leak even if deflected as much as 5 degrees, or when subjected to vibration, seismic tremors, expansion, contraction, external or internal test pressure. Physical Properties To prevent movement, horizontal pipe and fittings 5" and larger should be suitably braced by the use of blocks, rdding or other suitable methods at every branch or change of direction. Test: For best results, test one floor (ten feet) at a time. The system should be properly restrained; all bends, changes of direction and ends of runs should be restrained. Gasket Material: Ez-Tight gaskets are made of Neoprene as the sole elastomer. The physical characteristics of the Neoprene ensure that the gasket will not decay or deteriorate from contact with effluents in the pipe or chemicals in the soil or air around the pipe. Property Performance ASTM Test Method Hardness (nominal durometer ±5) as specified by the pipe manufacturer D2240 Elongation, min, percent D412 Tensile strength, min, psi (MPa) Tear Resistance, min, lbf/in. (N/cm) 1500 (10) 150 (268) 1500 (10) 150 (268) 1500 (10) 150 (268) D412 D624 How to Specify: All 2 inch through 6 inch hub and spigot cast iron soil pipe and fi ngs shall conform to ASTM A 74; joints shall be made either by caulked lead and oakum or by compression gaskets which conform to ASTM C 564. Compression set, max, percent D395 Heat aging, 96 h at 158 ± 2 F (70 ± 1 C) Hardness, increase, max, durometer points Loss in tensile strength, max, percent Loss in elongation, max, percent D573 Water absorption: Weight increase, max, percent D471 Ozone resistance Oil immersion: Volume increase, max, percent no cracks 80 no cracks 80 no cracks 80 D1149 D471 16

19 SUBMITTAL: TY SEAL GASKETS, HUB & SPIGOT CAST IRON SOIL PIPE & FITTINGS 1. Clean hub and spigot to be joined. DESCRIPTION TY SEAL is one piece compression gasket. It is used for joining hub and spigot cast iron soil pipe and fi ngs made according to ASTM A 74 GASKET MATERIAL TY SEAL gaskets are made of Neoprene as the sole elastomer. The physical characteris cs of the Neoprene ensure that the gasket will not decay or deteriorate from contact with effluents in the pipe or chemicals in the soil or air around the pipe. GASKET SPECIFICATION TY SEAL gaskets conform strictly to ASTM Standard C 564, latest issue. The TY SEAL mill specifica on meets or exceeds all requirements 2. Insert gasket in the hub, lubricate inside the gasket. 3. Align hub and spigot. PIPE SPECIFICATION TYLER hub and spigot cast iron soil pipe and fi ngs comply with the latest issue of ASTM A 74, ANSI A and Federal Specifica on WW P 401E. 4. Pull or push spigot through the gasket un l firmly sealed. 17

20 CREMCO SPECIALTY TRANSITION COUPLINGS List Prices CT-710NAT August 1, 2011 Part Number Code Size / Description Price Each Carton Qty / Weight # CP C 1½"CI/PL/ST - 1½"CI/PL/ST $ / 7 CP C 2"CI/PL/ST - 2"CI/PL/ST $ / 9 CP C 1½"CI/PL/ST - 2"CI/PL/ST $ / 12 CP C 3" PL/ST/X - 3"CI $ / 12 CP C 3" PL/ST/X - 4"CI $ / 16 CP C 4" PL/ST/X - 4"CI $ / 18 CP C 5" PL/ST/X - 5"CI $ / 25 CP C 6" PL/ST/X - 6"CI $ / 32 CP C 8" PL/ST/X - 8"CI $ / 29 CK C 3/4"PL/ST,1"K - 1½"CI/PL/ST $ / 10 CK C 1"PL/ST,1¼"K - 1½"CI/PL/ST $ / 9 CK C 1¼"PL/ST,1½"K - 1½"CI/PL/ST $ / 9 CK C 3/4"PL/ST,1"K - 2"CI/PL/ST $ / 15 CK C 1"PL/ST,1-1/4"K - 2"CI/PL/ST $ / 15 CK C 1¼"PL/ST,1½"K - 2"CI/PL/ST $ / 14 CK C 2"K - 2"CI/PL/ST $ / 11 CK C 1¼"PL/ST,1½"K - 3"CI/PL/ST $ / 24 CK C 2"K - 3"CI $ / 21 CK C 3"K - 3"CI $ / 15 CK C 2"K - 4"CI $ / 22 CK C 3"K - 4"CI $ / 28 CK C 4"K - 4"CI $ / 18 C C 1½"CI/PL/ST - 3"CI $ / 22 C C 2"CI/PL/ST - 3"CI $ / 22 C C 2"CI/PL/ST - 4"CI $ / 35 C C 3"CI - 4"CI $ / 26 C C 4"CI - 5"CI $ / 25 C C 4"CI - 6"CI $ / 30 P C 1"PL/ST,1-1/4K - 1"PL/ST,1-1/4K $ / 6 P C 3"PL/ST/X - 3"PL/ST/X $ / El Camino Ave. Corona, CA Phone: (951) Fax: (951)

21 P C 4"PL/ST/X - 4"PL/ST/X $ / 15 P C 3"PL/ST/X - 4"PL/ST/X $ / 25 P C 6"PL/ST/X - 6"PL/ST/X $ / 30 P C 8"PL/ST/X - 8"PL/ST/X $ / 20 PC C 3"CI/PL/ST - 3"PL/ST/X $ / 10 PC C 3"CI - 4"PL/ST/X $ / 25 PK C 3"K - 3"PL/ST/X $ / 15 K C ST X 1¼"PL/ST,1½"K - 1¼"PL/ST,1½K $ / 8 K C 2"K - 2"K $ / 8 K C 2"K - 1¼"PL/ST,1½K $ / 15 K C 3"K - 3"K $ / 10 K C 3"K - 2"K $ / 24 K C 4"K - 4"K $ / 15 KC C 1½"CI/PL/ST - 2"K $ / 15 KC C 2"CI/PL/ST - 3"K $ / 22 KC C 3"CI - 4"K $ / 30 KT C 1½"TU - 1¼"PL/ST,1½"K $ / 10 KT C 1½"TU - 2"K $ / 15 T C 1½"TU - 1½"CI/PL/ST $ / 9 T C 1½"TU - 2"CI/PL/ST $ / 15 BWT C 1½"TU - 1½"TU $ / 11 TWC C 3"CI - 4"TWP $ / 28 TWC C 4"CI - 4"TWP $ / 18 TWP C 3"PL/ST/X - 4"TWP $ / 28 TWP C 4"PL/ST/X - 4"TWP $ / 18 We reserve the right to withdraw this sheet without notice and price in effect at time of shipment will apply. Possession of this list price sheet shall not be construed as an offer to sell. Freight: Prepaid on all orders of 750 or more 19

22 TRANSITION COUPLINGS SUBMITTAL CERTIFICATIONS AND STANDARDS Meets ASTM C 1460 Meets ASTM C 564 Meets CSA B602 IAPMO File 5794 MATERIAL SPECIFICATION CLAMP: Type 301 AISI Stainless Steel SCREW: Type 305 AISI Stainless Steel SHIELD: Type 301 AISI Stainless Steel. Shield thickness.0072 GASKET: The gasket shall be manufactured from a properly vulcanized virgin compound, In which the primary elastomer is polychloroprene (Neoprene), conforming to ASTM C 564. TEST GASKET PHYSICAL TEST MIN. or MAX REQUIREMENTS ASTM METHOD Tensile Strength 1500 psi min. D 412 Elonga on 250 min. D 412 Durometer (Shore A) 70 ± 76 F ± 5 F D 2240 Accelerated Aging 15% max. tensile and 20% max. elonga on deteriora on, 10 points max. D 573 increase in hardness, all determina ons a er oven aging for 96 hrs at 158 F Compression Set 25% maximum a er 22 hrs at 158 F D 395 (Method B) Oil Immersion 80% max. volume change a er immersion in IRM 903 for 70 hrs at 212 F D 471 Ozone Cracking No visible cracking at 2x magnifica on of the gasket a er 100 hrs of exposure D 1149 in 1.5ppm ozone concentra on at 100 F. Tes ng and inspec on to be on gasket which is loop mounted to give approx. 20% elonga on on outer surface. Tear Resistance 150 lbs minimum per inch thickness D 624 Water Absorp on 20% max by weight a er 7 days at 158 F D

23 anaco anaco CAP List Prices TC-607NAT June 1, 2007 Caps off Plastic, Cast Iron, NO-HUB, Steel Pipe or Closet Bends 300 series all stainless steel worm drive screw and clamp assembly. Non-removable "Blow out Guard" built into body of cap. Materials conform to Cast Iron Soil Pipe Institute physical requirements spec Installs with screw driver or NO-HUB torque wrench Code Size List Price Quantity Per Carton Weight Per carton /2" $ lbs " $ lbs " $ lbs " $ lbs. We reserve the right to withdraw this sheet without notice and price in effect at time of shipment will apply Possession of this list price sheet shall not be construed as an offer to sell. Freight: Prepaid on all orders of 750 or more 1001 El Camino Ave. Corona, CA Phone: (951) Fax: (951)

24 anaco RIGID QUIK List Prices RQ-408NAT April 1, 2008 Code # Size/Description LIST CARTON QTY /2 CI, Plastic-1-1/4 Copper $ /2 CI,Plastic - 1 1/2 CI Plastic $ /2 CL,Plastic - 1 1/2 Copper, 1 1/4 Plastic $ CI Plastic - 1 1/4 Copper $ CI, Plastic - 1 1/2 CI Plastic $ CI, Plastic - 1 1/ 2 Copper, 1 1/4 Plastic $ CI, Plastic - 2 CI, Plastic $ CI, Plastic - 2 Copper $ CI, Plastic - 1 1/4 Copper $ CI, Plastic - 1 1/2 CI, Plastic $ CI, Plastic - 1 1/2 Copper, 1 1/4 Plastic $ CI, Plastic - 2 CI, Plastic $ CI, Plastic - 2 Copper $ CI, Plastic - 3 CI, Plastic $ CI, Plastic - 3 Copper $ CI, Plastic - 2 CI, Plastic $ CI, Plastic - 3 CI, Plastic $ CI, Plastic - 3 Copper $ CI, Plastic - 4 CI, Plastic $ We reserve the right to withdraw this sheet without notice and price in effect at time of shipment will apply.possession of this price sheet shall not be construed as an offer to sell. Freight: Prepaid on all orders of 750 pieces or more 1001 El Camino Ave. Corona, CA Phone: (951) Fax: (951)

25 RIGID QUIK COUPLINGS SUBMITTAL APPLICABLE PIPING STANDARDS Cast Iron ASTM A 888/CISPI 301 Copper DWV ASTM B 306 ABS DWV ASTM D 2661 & ASTM F 628 PVC DWV ASTM D 2665 & ASTM F 891 MATERIAL SPECIFICATION CLAMP: Stainless steel hose clamps are 300 series COUPLING: Injected molded exclusively from Santoprene rubber COUPLING SPECIFICATIONS Clamp: Stainless Quik comply with ASTM C 1461 and CSA B 602 IAPMO Lis ng 3251 DESCRIPTION Cremco Rigid Quik Couplings consist of a molded one piece Santoprene rubber gasket and 300 series stainless steel hose clamps. The couplings are designated as Rigid Unshielded due to the coupling s ability to provide the required resistance to lateral displacement without the assistance of a metallic shear ring (shield). The couplings are used to join various types and diameters of Drain, Waste, and vent (DWV) pipe and fi ngs together, above and below ground, inside and outside of the building. 23

26 End of Document 24