SECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3

Size: px
Start display at page:

Download "SECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3"

Transcription

1 SECTION VIII (Sub-section 430) Wastewater Valves and Appurtenances Article Page 1. General thru Gate Valves thru Plug Valves thru Check Valves Tapping Valves Valve Boxes Air Release Valves Material Warranty Contractor Warranty Measurement and Payment 430-6

2 WASTEWATER VALVES AND APPURTENANCES SUB-SECTION GENERAL 1.1 SCOPE OF WORK The Contractor shall furnish and install all gate valves, check valves, plug valves and other special valves and appurtenances as shown on the drawings and specified herein. All references to industry standards (ASTM, ANSI, AWWA, etc.) shall be to the latest revision unless otherwise specified. Only those materials included in the Citrus County s approved materials and equipment list shall be installed unless otherwise directed. All materials shall be new unless specifically called for otherwise SHOP DRAWING SUBMITTALS Actual catalog data, brochures and descriptive literature will not be required for items of standard usage which meet the requirements of Sub- Section 430 and are included in the approved materials and equipment list. Any specialty item not shown in this list will require a complete shop drawing submittal. The Engineer may, at any time, require the Contractor to provide a complete detailed shop drawing submittal for any material which, in the Engineer's opinion, may not be in compliance with the Citrus County Utility Standards ROTATION OF OPENING All valves installed within a sewer system to be Citrus County owned shall open by turning to the left or counterclockwise, when viewed from the stem. 1.4 EXTENSION STEMS Where extension stems are required, substantial, adjustable wall brackets and extension stems shall be furnished and located as directed. Extension stems shall be provided on all buried valves when the operating nut is deeper then 30 inches below the final grade. Sufficient stem extension shall be provided so that the nut will be no more than 30 inches below finished grade. 1.5 PAINTING OF VALVES AND VALVE BOX LIDS The interior and exterior of all valves shall be epoxy coated. The topside of all sewer valve box covers shall be painted green with oil based, trafficrated paint. WASTEWATER VALVES AND APPURTENANCES 430-1

3 1.6. LOCATING MARKERS FOR VALVES A V cut shall be carved in the curb closest/adjacent to a below grade valve. This V cut shall be painted green. 2.0 GATE VALVES 2.1 GENERAL Gate valves 3 inches to 12 inches in diameter shall be designed for 200 psi minimum working pressure. Valves over 12 inches in diameter shall be 150 psi minimum working pressure. Gate valves, when full open, shall have a clean waterway equal to the nominal diameter of the pipe. The operating nut or wheel shall have an arrow cast in the metal indicating the direction of opening. Each valve shall have the manufacturer's distinctive marking, pressure rating and year of manufacture cast on the body. Prior to shipment from the factory, each valve shall be tested by applying to it a hydrostatic pressure equal to twice the specified working pressure. Gate Valves smaller than 3 shall be Milwaukee Valve No (nonrising stem) or 1153 (rising stem) or equal, 200 lb. SWP, 400 lb. WOG, heavy duty service solid wedge disc, stainless seat gland packed, union bonnet and threaded ends BURIED VALVES Gate Valves shall be iron body, fully bronze mounted, fully rubber encapsulated, resilient seat, solid wedge, non-rising stem type. Resilient seat gate valves shall conform to applicable sections of AWWA Standards C509. Valve interiors shall be epoxy coated and suitable for use in municipal wastewater All buried gate valves shall be provided with a 2 inch square operating nut and valve box All gate valves 20 inch or larger must be bevel geared for both horizontal and vertical installations. All valves shall be installed vertically unless additional depth of bury is impossible due to physical obstructions ABOVE GROUND VALVES Gate valves located above ground or inside structures shall be hand wheel operated, non-rising stem type with flanged ends and be of the same general construction as buried valves. WASTEWATER VALVES AND APPURTENANCES 430-2

4 2.4. VALVE JOINTS 3.0 PLUG VALVES All gate valves shall have mechanical joint ends, flanged ends, or screw joints to fit the pipe run in which they are to be used, except valves installed on push-on joint pipe shall have mechanical joint ends unless otherwise specified GENERAL All plug valves, unless specifically shown otherwise on the drawings, shall be of the non-lubricated, eccentric plug type with buna "N" neoprene, epoxy or fusion bonded, nylon faced plugs. Valve bodies shall be ASTM A126, Class B cast iron. Port areas of 4 inch through 20 inch valves shall be at least 80% full pipe area and 24 inch and larger valves shall be at least 70% full pipe area. The valve seat material shall consist of either a welded in 1/8 inch overlay of 90% pure nickel, or 316 stainless steel screwed into the cast iron body. Upper and lower plug stem bearings shall be sleeve-type of a stainless steel or other non-corrosive bearing material. The packing shall be adjustable and the bonnet shall be bolted. All bolts, nuts, and washers shall be 316 stainless steel for buried, non-buried, and pit installed service. All buried valves on push-on joint pipe shall have mechanical joint ends and meet the requirements of ANSI A All exposed (nonburied) valves shall have flanged ends in accordance with American Standard B16.1, Class 125. The valves shall be rated for a minimum of 150 psi, non-shock cold W.O.G. and shall provide drip-tight shut off with this pressure in either direction. The operating nut or hand wheel shall have an arrow cast in the metal indicating direction of opening. The valve manufacturer shall furnish certified copies of performance, leakage and hydrostatic testing as outlined in AWWA C504. The interior of all plug valves shall be epoxy coated OPERATORS/ACTUATORS All plug valves 8 inches and larger shall be equipped with totally enclosed worm gear actuators complying with AWWA C504. All gearing shall run in oil. The actuator housing shall be semi-steel with seals to prevent dirt or water from entering the housing. Shaft bearings shall be permanently lubricated bronze bushings. Appropriately sized hand wheel operators shall be provided for each non-buried, gear-actuated valve. WASTEWATER VALVES AND APPURTENANCES 430-3

5 3.3. BURIED VALVES Buried valves shall have seals on all shafts and gaskets on the valve covers. Buried valves shall be provided with 2 inch square operating nuts VALVE JOINTS 4.0 CHECK VALVES All plug valves shall have mechanical joint ends if buried on push-on joint pipe or flanged ends if above ground on flanged pipe. Check valves shall conform to the requirements of AWWA C508. Check valves shall be standard iron body, swing type with straight-away passageway of full pipe areas. Valves shall be bronze mounted with self-adjusting, rubber-faced disc. Disc shall operate on a 304 stainless steel shaft connected to a 316 stainless steel outside lever and 316 stainless steel spring. Valves shall be 150 psi working pressure minimum, except as noted otherwise. Springs to be rated as per manufacturer's recommendations. Buried check valves shall be installed in an approved access box with traffic rated cover. 5.0 TAPPING VALVES 5.1. BODIES Tapping valves shall be iron body, bronze mounted gate valves, non-rising stem, open left, resilient seat, 2 inch square operating nut, for vertical mounting in approximately level setting on buried wastewater lines. The valve ends shall be mechanical joint for use with cast iron pipe on one side and standard flanged (class 125) on the other. Valves shall conform to Sub-Section 100 of these specifications HYDROSTATIC AND LEAKAGE TEST After installing a tapping sleeve and valve, a hydrostatic and leakage test shall be performed. The test will be conducted by introducing water into a tap or test hole located at the neck of the outlet half of the sleeve, on sleeves furnished with said tap, and with the tapping valve in the closed position. Sleeves shall be provided with a test plug. The sleeve and valve shall be capable of maintaining a test pressure of 150 psi for 30 minutes duration, with no sign of visible leaks. All leaks shall be repaired by removing and replacing defective items with items free of defects, after which the sleeve and valve shall be re-tested. Such repair and re-testing shall be done until the installation passes the specified test. The Contractor shall furnish and install any necessary temporary restraints, gauges, pumps and other incidental and appurtenant items necessary to complete this work, and shall remove same upon completion of the test. A watertight plug shall then be inserted into the test hole. WASTEWATER VALVES AND APPURTENANCES 430-4

6 6.0 VALVE BOXES 6.1. GENERAL The Contractor shall furnish, assemble and install an adjustable 3-piece valve box for each buried valve. Each valve box installed in non-paved areas shall be installed with a 24 inch square, 6 inch thick concrete collar poured to grade around the top of the valve box cover. The concrete shall have a minimum strength of 2500 psi. Provide brass identification tag with Sewer, valve size, and valve type engraved on tag epoxyed or riveted to interior of valve box. Tag shall be 2 inch diameter, 1/8 inch thick brass, located a maximum of 2 inches below the top of the valve box BOXES Adjustable 3-piece valve boxes of suitable length shall be used. Cover shall be marked "Sewer". The top section shall be adjustable for elevation and shall be set to allow equal movement above and below finished grade. The base shall be centered over the valve and shall be on line with nut at top of valve stem and the entire assembly shall be plumb. Boxes for paved areas shall be cast iron, and boxes for non-paved areas may be PVC. Cast iron castings shall be manufactured of clean, even grain, gray cast iron conforming to ASTM Designation A48, Class 20B, Gray Iron Castings; and shall be smooth, true to pattern, free from blow holes, sand holes, projections, or other harmful defects and shall be coated with a single thin coat of coal tar epoxy. The cover will not rock after it has been seated in any position in its associated jacket DEBRIS CAP Debris caps shall be required in all valve boxes when shown on the plans and specified. The debris cap shall be comprised of a hollow member having a cylindrical outer surface, a closure for one end and three point resilient contact pads projecting from the outer surface. One contact pad shall be movable by means of a cam having a low angle of advance whereby external forces applied to the cam via the movable contact pad will not cause rotation of said cam. The cap shall have a flexible skirt providing an outward seal preventing debris from getting past the cap. The cap must withstand, without slipping, a minimum vertical force of 50 lbs. at a loading rate of 1.0 inches/minute. The cap shall have retaining prongs to retain a standard locating coil, and shall be capable of installing a standard fitting for Lock-out/Tag-out in compliance to all standards and requirements of State and Federal OSHA guidelines. WASTEWATER VALVES AND APPURTENANCES 430-5

7 7.0 AIR RELEASE VALVES Where called for on the drawings, valves shall be the Air Release Valve type as listed in the Citrus County Utilities Division (UD) standard details. An isolation valve shall be installed at the connection to the force main for general maintenance to the valve. 8.0 MATERIAL WARRANTY The manufacturer of materials furnished on the project shall supply to Citrus County, a one (1) year unconditional warranty. The warranty shall be limited to the material that shall constitute complete replacement and delivery to the site of materials only to replace defective materials with new materials conforming to the specifications CONTRACTOR WARRANTY The Contractor shall supply to Citrus County a one (1) year unconditional warranty. The warranty shall include materials and installation and shall constitute complete replacement and delivery to the site of materials and installation of same to replace defective materials or defective workmanship with new materials/workmanship conforming to the specifications MEASUREMENT AND PAYMENT The quantities of items to be measured and paid for under this section shall be as shown in the contract proposal, completed and accepted, including all incidental work and related materials. WASTEWATER VALVES AND APPURTENANCES 430-6

PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA

PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending

More information

SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION WATER DISTRIBUTION VALVES

SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION WATER DISTRIBUTION VALVES SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION 33 12 16 WATER DISTRIBUTION VALVES PART 1 GENERAL... 2 1.1 Description... 2 1.2 Reference Specifications, Codes, and

More information

516509_tabs 11/16/10 4:55 AM Page 1 FIRE HYDRANTS

516509_tabs 11/16/10 4:55 AM Page 1 FIRE HYDRANTS Date Printed: November 2010 FIRE HYDRANTS or Tyton (6"),6, or 8" A EDDY FIRE HYDRANTS PARTS LIST WORKING PRESSURE: 150 PSI Note: Discontinued For Reference Only 350 PSI Working Pressure

More information

FLOAT CONTROL VALVES

FLOAT CONTROL VALVES PROJECT NAME LOCATION FLOAT CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 8 in. (200 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard

More information

MODULATING FLOAT CONTROL VALVE

MODULATING FLOAT CONTROL VALVE PROJECT NAME LOCATION MODULATING FLOAT CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL

More information

SOLENOID CONTROL VALVE

SOLENOID CONTROL VALVE PROJECT NAME LOCATION SOLENOID CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 4 in. (100 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard

More information

MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE

MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE ISO 9001 CERTIFIED MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve,

More information

PRESSURE REDUCING CONTROL VALVES

PRESSURE REDUCING CONTROL VALVES PROJECT NAME LOCATION PRESSURE REDUCING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL

More information

SECTION VALVES

SECTION VALVES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:

More information

Available End Connections & Size Range

Available End Connections & Size Range ECCENTRIC PLUG VALVES Size Range 3"-24" Water Working Hydrostatic Size Range Pressure psi Test psi 3"-12" 175 350 14"-24" 150 300 Available End Connections & Size Range Figure No. Flanged 3"-24" F-5412

More information

PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE

PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE PROJECT NAME LOCATION PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2-1/2 in. (65 mm) through 18 in. (450 mm) Control

More information

Suggested Specifications

Suggested Specifications ISO 9001 Certified Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve, setting higher standards for dependable performance

More information

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE

AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE CONSTRUCTION STAINLESS STEEL PIPE PLUG Allows installation of pressure gauge. STAINLESS STEEL FASTENERS Helps provide corrosion resistance.

More information

PRESSURE RELIEF / SUSTAINING CONTROL VALVES

PRESSURE RELIEF / SUSTAINING CONTROL VALVES PROJECT NAME LOCATION PRESSURE RELIEF / SUSTAINING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART

More information

COMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES 2.01 COMBINATION RESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVE

COMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES 2.01 COMBINATION RESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVE PROJECT NAME LOCATION COMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900

More information

ALTITUDE CONTROL VALVES FOR ONE WAY FLOW

ALTITUDE CONTROL VALVES FOR ONE WAY FLOW PROJECT NAME LOCATION ALTITUDE CONTROL VALVES FOR ONE WAY FLOW INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1

More information

ECCENTRIC PLUG VALVES

ECCENTRIC PLUG VALVES Serving the Water & Waste Water Industry Since 1878 ECCENTRIC PLUG VALVES C517 3 24 sizes available Multiple end connections available M&H Valve is a division of McWane, Inc. www.mh-valve.com AVAILABLE

More information

SECTION VALVES PART 1 -GENERAL

SECTION VALVES PART 1 -GENERAL SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This

More information

1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service.

1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service. KENNEDY KENNEDY VALVE MODEL VALVE KS-RW 1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service. 2. The valves shall have a cast

More information

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING SUNY GENESEO 220523-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

A. This Section includes general duty valves common to several HVAC piping systems.

A. This Section includes general duty valves common to several HVAC piping systems. SECTION 23 05 23 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

SECTION VALVES PART 1 - GENERAL

SECTION VALVES PART 1 - GENERAL 1.01 RELATED DOCUMENTS SECTION 15100 VALVES PART 1 - GENERAL A. The work in this section includes the furnishing and installation of all control valves and accessories shown on the construction plans and

More information

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR PLUMBING PIPING Page

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR PLUMBING PIPING Page Page 220523-1 SECTION 220523 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

September 2012 / M&H C502 / Model 129

September 2012 / M&H C502 / Model 129 GENERAL FEATURES / GENERAL SPEC M&H AWWA C502 FIRE HYDRANTS Model 129 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approved Type: Compression type, opening against line

More information

VALVES, FIRE HYDRANTS, AND APPURTENANCES

VALVES, FIRE HYDRANTS, AND APPURTENANCES VALVES, FIRE HYDRANTS, AND APPURTENANCES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Butterfly Valves B. Gate Valves C. Tapping Valve Assemblies D. Fire Hydrant Assemblies E. Flushing Devices (Blowoffs)

More information

SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class 150/250 December 2012

SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class 150/250 December 2012 SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class December 2012 1. SCOPE This product specification covers class rubber-seated butterfly

More information

SECTION VALVES AND OPERATORS

SECTION VALVES AND OPERATORS SECTION 15200 VALVES AND OPERATORS PART 1 - GENERAL 1.1 SUBMITTALS A. Shop Drawings: 1. Product data sheets for make and model. 2. Complete catalog information, descriptive literature, specifications,

More information

The SWL Series Swing Check Valves Meets AWWA C Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution

The SWL Series Swing Check Valves Meets AWWA C Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution The Series Meets AWWA C-508-01 Standards (Full Waterway) Accepts Air Cushions Cost-effective Swing Check Valve Solution Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick,

More information

GENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.

More information

Valve Selection. 1. Function and service considerations

Valve Selection. 1. Function and service considerations 1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.

More information

UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:

UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number: SECTION 230523 GENERAL DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. The following

More information

SECTION 17 FIRE HYDRANT ASSEMBLIES General

SECTION 17 FIRE HYDRANT ASSEMBLIES General SECTION 17 FIRE HYDRANT ASSEMBLIES 17-1.01 Scope 17-1 General This section describes the requirements for furnishing and installing as appurtenances to treated water mains. These requirements include the

More information

SWING CHECK VALVES SERIES 52-SC SERIES 600

SWING CHECK VALVES SERIES 52-SC SERIES 600 SWING CHECK VALVES SERIES 52-SC SERIES 600 FEATURES/BENEFITS/SPECIFICATIONS AMERICAN Flow Control Series 52-SC Swing Check Valves incorporate design features to help increase service life for water and

More information

1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves.

1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves. Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product

More information

Herpteraium SECTION VALVES GENERAL

Herpteraium SECTION VALVES GENERAL SECTION 22 05 23 VALVES GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Iron swing check valves. 3. Iron gate valves. 4. Iron globe valves. B.

More information

SECTION MISCELLANEOUS VALVES

SECTION MISCELLANEOUS VALVES SECTION 05140 - PART 1 - GENERAL 1.1 WORK OF THIS SECTION A. The WORK of this Section includes providing miscellaneous valves as indicated, complete and operable, including accessories and operators. 1.2

More information

SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.

SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems. SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000

More information

Dos Rios Chlorine Contact Basin Scum Well Rehabilitation Project Solicitation Number: CO Job No.:

Dos Rios Chlorine Contact Basin Scum Well Rehabilitation Project Solicitation Number: CO Job No.: Dos Rios Chlorine Contact Basin Scum Well Rehabilitation Project Solicitation Number: CO-00031 Job No.: 15-6504 To Respondent of Record: ADDENDUM I November 20, 2015 This addendum, applicable to work referenced

More information

SPECIFICATIONS - DETAILED PROVISIONS Section Valve and Gate Operations CONTENTS

SPECIFICATIONS - DETAILED PROVISIONS Section Valve and Gate Operations CONTENTS SPECIFICATIONS - DETAILED PROVISIONS Section 13446 - Valve and Gate Operations CONTENTS PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 SUBMITTALS... 1 1.04 QUALITY ASSURANCE... 1 1.05

More information

A. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.

A. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems. SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing

More information

Water Distribution Solutions

Water Distribution Solutions Water Distribution Solutions Table of Contents WaterMaster 5CD250 Fire Hydrants 6 WaterMaster 5BR250 Fire Hydrants 8 FlowMaster Resilient Wedge Gate Valves 11 Valve Boxes 17 Meter Boxes 22 Table of Contents

More information

EXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES

EXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES EXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES AVK VALVES STANDARD FEATURES AVK STANDARD FEATURES AVK Gate Valves are made of ductile iron and meet or exceed AWWA C509 or C515 ASTM A582 stainless

More information

UPDATE LOG FOR TECHNICAL PROVISIONS DIVISION 4 Date Item(s) Changed Page # 10/1/13 TECHNICAL PROVISIONS DIVISION 4 VALVE SPECIFICATIONS

UPDATE LOG FOR TECHNICAL PROVISIONS DIVISION 4 Date Item(s) Changed Page # 10/1/13 TECHNICAL PROVISIONS DIVISION 4 VALVE SPECIFICATIONS UPDATE LOG FOR TECHNICAL PROVISIONS DIVISION 4 Date Item(s) Changed Page # 10/1/13 TECHNICAL PROVISIONS DIVISION 4 VALVE SPECIFICATIONS Replace entire document dated 1/12 with the revised document dated

More information

SECTION SWING CHECK VALVES

SECTION SWING CHECK VALVES PART 1 GENERAL 1.1 DESCRIPTION This section includes materials, testing, and installation of swing check valves as shown in the Drawings and specified herein, in accordance with the requirements of the

More information

CITY OF TAMPA ADDENDUM 2. July 13, Contract 17-C-00030; David L. Tippin Water Treatment Facility Lime Slaker Replacement

CITY OF TAMPA ADDENDUM 2. July 13, Contract 17-C-00030; David L. Tippin Water Treatment Facility Lime Slaker Replacement CITY OF TAMPA Bob Buckhorn, Mayor CONTRACT ADMINISTRATION DEPARTMENT Michael W. Chucran, Director ADDENDUM 2 July 13, 2017 Contract 17-C-00030; David L. Tippin Water Treatment Facility Lime Slaker Replacement

More information

mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY

mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY 129 HYDRANT YESTERDAY, TODAY, & TOMORROW For more than 85 years, the M&H

More information

AMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT

AMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT AMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available Listed by Underwriters Laboratories, Inc. and Approved by FM Approvals in applicable configurations.

More information

Suggested Specifications

Suggested Specifications TTR Group Inc. The Engineered Valve & Speciality Products Company Suggested Specifications Meeting and Exceeding AWWA Guidelines AWWA C 504 Latest Revision Butterfly Valves AWWA C 508 Latest Revision Check

More information

Division 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING

Division 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division

More information

Ballcentric Plug Valve

Ballcentric Plug Valve Ballcentric Plug Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry

More information

ADMIRAL HYDRANT. clowvalve.com

ADMIRAL HYDRANT. clowvalve.com clowvalve.com ADMIRAL HYDRANT AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 350 PSI WORKING PRESSURE AVAILABLE 10-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane,

More information

M&H AWWA C508 STANDARD SWING CHECK VALVES

M&H AWWA C508 STANDARD SWING CHECK VALVES GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by

More information

American Flow control Series 2500

American Flow control Series 2500 American Flow control 14-66 Series 2500 Resilient wedge gate valve FLOW CONTROL Construction Ductile iron operating nut Provides strength and durability. Lifting DEVICES 14-66 Valve is constructed of high-strength

More information

LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER ADDITIONS AND RENOVATIONS

LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER ADDITIONS AND RENOVATIONS LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER. SECTION.0 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART - GENERAL. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and

More information

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR HVAC PIPING Page

Michigan State University Construction Standards. GENERAL-DUTY VALVES FOR HVAC PIPING Page Page 230523-1 Copyright 2005 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified by MSU Physical Plant

More information

SECTION GENERAL-DUTY VALVES FOR HVAC PIPING. A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section.

SECTION GENERAL-DUTY VALVES FOR HVAC PIPING. A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section. SECTION 23 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Gate Valves 2. Balancing Valves 3. Ball Valves 4. Butterfly Valves 5. Swing Check Valves 1.2 RELATED SECTIONS A. Contents of Division

More information

Water Distribution Solutions

Water Distribution Solutions Water Distribution Solutions Table of Contents WaterMaster 5CD250 Fire Hydrants 6 WaterMaster 5BR250 Fire Hydrants 8 FlowMaster Resilient Wedge Gate Valves 11 Valve Boxes 17 Meter Boxes 22 Table of Contents

More information

Henderson Engineers, Inc. SECTION GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS

Henderson Engineers, Inc. SECTION GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS SECTION 220523 - GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS 1.1 SUMMARY A. This Section includes general duty valves common to most plumbing piping systems. 1. Special purpose

More information

SECTION PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL

SECTION PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL SECTION 22 10 10 PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and

More information

SECTION PUMPS GENERAL PUMPS PART RELATED DOCUMENTS

SECTION PUMPS GENERAL PUMPS PART RELATED DOCUMENTS SECTION 15160 - PUMPS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Basic Requirements: Provisions of Section 15010, BASIC MECHANICAL REQUIREMENTS and Section 15030, ELECTRICAL REQUIREMENTS FOR MECHANICAL

More information

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING

SECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. Provide labor, materials, equipment, and services necessary to install valves required to complete the work indicated on drawings. B. ASME Compliance: 1. ASME

More information

HP250II AND HP250 BUTTERFLY VALVES Engineering Creative Solutions for Fluid Systems Since 1901

HP250II AND HP250 BUTTERFLY VALVES Engineering Creative Solutions for Fluid Systems Since 1901 H250II AND H250 BUTTERFLY VALVES Engineering Creative Solutions for Fluid Systems Since 1901 TABLE OF CONTENTS RATT H250II Scope of Line... 1 Design and Construction Details... 1 ipe Mating Chart... 1

More information

SECTION FACILITY FUEL OIL PIPING

SECTION FACILITY FUEL OIL PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Specification Sections, apply to this Section. B. Related Sections:

More information

AUTOMATION ACCESSORIES IN-PLANT VALVE PRODUCTS EXTENSION STEMS FLOORBOX STEM GUIDES FLOORSTANDS COMMITTED TO ENVIRONMENTAL RESPONSIBILITY FLAP VALVES

AUTOMATION ACCESSORIES IN-PLANT VALVE PRODUCTS EXTENSION STEMS FLOORBOX STEM GUIDES FLOORSTANDS COMMITTED TO ENVIRONMENTAL RESPONSIBILITY FLAP VALVES INCREASING SWING CHECK VALVES FLAP VALVES SWING CHECK VALVES AUTOMATION ACTUATION CLOW VALVE has furnished valves with many assorted types of motorized to operate our valves. The gate valves use multi-turn,

More information

Approved Branded Traceable Fire Protection & Waterworks Valves

Approved Branded Traceable Fire Protection & Waterworks Valves Approved Branded Traceable Fire Protection & Waterworks Valves (800) 766-0076 www.smithcooper.com Los Angeles, CA Atlanta, GA Vancouver, WA Chicago, IL AWWA C515 Compliant CONSIDER Your Options Tamper

More information

AWWA Swing Check Valves

AWWA Swing Check Valves AWWA Swing Check Valves Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the

More information

MEDALLION HYDRANT. clowvalve.com AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY

MEDALLION HYDRANT. clowvalve.com AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY clowvalve.com MEDALLION HYDRANT AWWA C50 UL LISTED FM APPROVED NSF 6/37 CERTIFIED 50 PSI WORKING PRESSURE 0-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane, Inc. MEDALLION HYDRANT FIRE PROTECTION

More information

Series 800 AWWA Butterfly Valves

Series 800 AWWA Butterfly Valves Series 800 AWWA Butterfly Valves Valve and Gate Group A Century of Experience GA valves are known for long term reliability in the most demanding water and wastewater applications. Whether a simple check

More information

DIMENSIONS (approximate)

DIMENSIONS (approximate) Page 1 of 8 a NRS GATES OS&Y GATES company Model 48 Resilient Wedge Gate Valve SPECIFICATION SUBMITTAL SHEET FEATURES Sizes: 2 1/2" 3" 4" 6" 8" 10" 12" Maximum working water pressure 200 PSI Maximum working

More information

M&H AWWA C508 STANDARD SWING CHECK VALVES

M&H AWWA C508 STANDARD SWING CHECK VALVES GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by

More information

TRUMBULL MUD VALVES. Installation, Operation and Maintenance Manual

TRUMBULL MUD VALVES. Installation, Operation and Maintenance Manual TRUMBULL MUD VALVES Cast Iron and Stainless Steel Models Rising Stem and Non-Rising Stem Styles Installation, Operation and Maintenance Manual Table of Contents A. General Information.............................

More information

American Flow control 5 1/4 B-62-B-5

American Flow control 5 1/4 B-62-B-5 American Flow control 5 1/4 B-62-B-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING

More information

5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL

5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL 5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and FM Approved in applicable configurations. ONE-PIECE

More information

SECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY

SECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY SECTION 230533 - PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Static pressure

More information

PART 1 GENERAL 1.1 SCOPE OF WORK

PART 1 GENERAL 1.1 SCOPE OF WORK SECTION 15110 PART 1 GENERAL 1.1 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals required and install complete and ready for operation all valves and appurtenances as shown on

More information

Specifications For Valve Insertion System

Specifications For Valve Insertion System Specifications For Valve Insertion System Equipment For Valve Insertion Pipe Sizes: 4 (100mm) Through 12 (300mm) 1.0 SCOPE This specification covers the furnishing, complete EZ Valve insertion system.

More information

Triton. Wet Barrel Ductile Iron. Fire Hydrants. Reliable Connections. operation / Maintenance manual. Inspection and Installation 2

Triton. Wet Barrel Ductile Iron. Fire Hydrants. Reliable Connections. operation / Maintenance manual. Inspection and Installation 2 operation / Maintenance manual MUELLER TAble of contents PAGE Triton Inspection and Installation 2 Installation and Testing 3 Wet Barrel Ductile Iron Maintenance Instructions 4 Parts 5 Notes 6-7 Fire Hydrants

More information

SECTION 1019 VALVES AND APPURTENANCES GENERAL: Valves shall have manufacturer's name and pressure rating cast in raised letters.

SECTION 1019 VALVES AND APPURTENANCES GENERAL: Valves shall have manufacturer's name and pressure rating cast in raised letters. SECTION 1019 VALVES AND APPURTENANCES Delete this Section in its entirety and replace with the following: SECTION 1019 VALVES AND APPURTENANCES 1019-1 GENERAL: Valves shall have manufacturer's name and

More information

AMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT

AMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT AMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and Approved by FM Approvals in applicable configurations. ONE-PIECE BRONZE

More information

SECTION (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING

SECTION (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING SECTION 22 05 23 (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Valves. B. Related Sections: 1.02 REFERENCES 1. Section 22 05 53 (15075) Identification

More information

Ford Fabricated Steel Products

Ford Fabricated Steel Products Ford Fabricated Steel Products Section N2 12/2000 The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487 Overseas

More information

SECTION VALVES. A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section.

SECTION VALVES. A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section. PART 1 GENERAL 1.01 DESCRIPTION OF WORK SECTION 22412 VALVES A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section. B. All valves, except those are 2 in diameter

More information

Model-1 Natural Gas Valves

Model-1 Natural Gas Valves Flanged End 285 Screwed Weld End Locking Devices KEROTEST Model-1 s Short Weld End Long Weld End Weld x Flange 500 / 740 Flanged End 500 / 740 Weld x Flange 285 Model-1 Short Weld End Standard Welding

More information

Data Sheet Issue A

Data Sheet Issue A General Description The Rapidrop Fig 601/602 dry barrel post / flushing fire hydrant is designed to be a trouble free, easy to maintain hydrant. The Fig 601/602 fire hydrant is rated for a working pressure

More information

SERIES 900 PLUG VALVES

SERIES 900 PLUG VALVES K - F L O VA LV E S SERIES 900 PLUG VALVES VA LV E S F R O M 1 4 T H R U 4 8 PO Box 411 Berwick PA 18603 800-247-VALV www.crispinvalve.com 900 SerieS Plug Valve Sizes 14-48 Crispin/K-Flo Series 900 is

More information

Harlingen Water Works System Approved Products List For Subdivisions. January 11, 2005

Harlingen Water Works System Approved Products List For Subdivisions. January 11, 2005 Harlingen Water Works System Approved Products List For Subdivisions January 11, 2005 Revised March 24, 2016 Harlingen Water Works System Approved Products List for Subdivisions Table of Contents: 1. Valves

More information

CCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901

CCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901 CCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry

More information

FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL. Item No.s/Description

FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL. Item No.s/Description FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL Item No.s/Description Item No. Description Material Specification HYDRANT Qty. Req d Item No. Description Material Specification 1 Operating

More information

1.2 REFERENCES.1 American National Standards Institute (ANSI)/ American Society of Mechanical Engineers (ASME)

1.2 REFERENCES.1 American National Standards Institute (ANSI)/ American Society of Mechanical Engineers (ASME) Issued 2005/06/01 Section 15111 Valves Bronze Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards Institute (ANSI)/

More information

CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION

CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION TESTING AND DESIGN SPECIFICATIONS (PER AWWA C502 / NSF /ULC & FM) 1. Hydrant shall be manufactured in accordance with AWWA C502 latest revision

More information

Val-Matic 3-Way Tapered Plug Valve

Val-Matic 3-Way Tapered Plug Valve Val-Matic 3-Way Tapered Plug Valve Manual No. CCPV-OM4-1 Operation, Maintenance and Installation Manual INTRODUCTION.2 RECEIVING AND STORAGE 2 VALVE CONSTRUCTION..2 DESCRIPTION OF OPERATION. 3 INSTALLATION

More information

KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES

KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES KENNEDY VALVE AWWA C515 Resilient Wedge Gate Valves Meet or Exceed the Requirements of AWWA Standard C515 UL-262/FM-1120/1130 ULC-Underwriters of Canada 2 1/2

More information

American Flow control 5 1/4 b-84-b-5

American Flow control 5 1/4 b-84-b-5 American Flow control 5 1/4 b-84-b-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING

More information

SECTION FIRE HYDRANTS WITH HYDRANT LOCKS

SECTION FIRE HYDRANTS WITH HYDRANT LOCKS SECTION 33 12 19 FIRE HYDRANTS WITH HYDRANT LOCKS PART 1: GENERAL 1.01 SCOPE A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33

More information

FIRE PROTECTION PRODUCTS

FIRE PROTECTION PRODUCTS SUPER CENTURION FIRE HYDRANT Mueller Super Centurion Fire Hydrant Since its introduction in 1976, millions of Centurion fire hydrants have been installed throughout North America. There are a number of

More information

SECTION GENERAL-DUTY VALVES FOR HVAC. A. Section includes valves for building services piping.

SECTION GENERAL-DUTY VALVES FOR HVAC. A. Section includes valves for building services piping. SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. Section includes valves for building services piping. 1.2 REFERENCES A. AGA Z21.22 (American Gas Association) - Relief Valves

More information

AMERICAN FLOW CONTROL 4"-48" SERIES 2500 TAPPING VALVES

AMERICAN FLOW CONTROL 4-48 SERIES 2500 TAPPING VALVES AMERICAN FLOW CONTROL 4"-48" SERIES 2500 TAPPING VALVES FEATURES/SPECIFICATIONS/MAINTENANCE FEATURES AMERICAN provides tapping valves for sizes 4 in. 48 in. rated at 250 psig pressure. Tapping valves 4

More information

AWWA SWING CHECK VALVES. Engineering Creative Solutions for Fluid Systems Since 1901

AWWA SWING CHECK VALVES. Engineering Creative Solutions for Fluid Systems Since 1901 AWWA SWING CHECK VALVES Engineering Creative Solutions for Fluid Systems Since 1901 TABLE OF CONTENTS AWWA SWING CHECK VALVE Series 8001 Lever & Weight or Spring...1 Series 9001 Lever & Weight or Spring...2

More information