GENUINE PARTS INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "GENUINE PARTS INSTALLATION INSTRUCTIONS"

Gilbert Ramsey
5 years ago
Views:

GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder

A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood Protector E 6 Small F 4 Large G 6 Abrasive Tape H

Description A B C D E F G H I J K L TOOLS REQUIRED: Drill 5/16" (8mm) Drill Bit Scissors Masking Tape #2

CAUTIONS / NOTES: Before installation clean hood surface with mild soap and water using a soft cloth or

1 GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood Protector E 6 Small F 4 Large G 6 Abrasive Tape H 4 Plug I 6 Neoprene Washer (Rectangle) J 6 Fibre Washer K 4 Plastic Washer L 1 Alcohol Wipe (2-pk) Part Description A B C D E F G H I J K L TOOLS REQUIRED: Drill 5/16" (8mm) Drill Bit Scissors Masking Tape #2 Phillips driver Clip Removal Tool / Flathead driver Non-Permanent Marker / Pencil Clean Cloth INSTALLATION CAUTIONS / NOTES: Before installation clean hood surface with mild soap and water using a soft cloth or chamois. Never use ammonia based cleaners or solvents on the hood protector. Dealer Installation Recommended. Allow tape to cure for 4 hours before driving vehicle. 1 of 6 T99D5 9PJ0A II Rev. 05/31/16

Fig. 1 1) Clean hood installation area using soapy water and clean cloth. Fig. 2 2) 3) 4) Open hood. Cover engine compartment with protective blanket to catch any dropped hardware.

2 Fig. 1 1) Clean hood installation area using soapy water and clean cloth. Fig. 2 2) 3) 4) Open hood. Cover engine compartment with protective blanket to catch any dropped hardware. Remove 4 grommets using clip removal tool or flathead screwdriver. 6) 6) 6) 6) Fig. 3 5) 6) Attach masking tape to drill bit 6mm from end. Enlarge existing holes using 5/16" (8mm) drill bit at 4 locations shown. Note: Make sure drill is on low speed and do not use excessive force. 5/16th 8mm 7) Remove any metal shavings and burrs from drilled holes. 2 of 6 T99D5 9PJ0A II Rev. 05/31/16

Abrasive Tape 9) Abrasive Tape 9) Wrap abrasive tape over hood lip.

3 8) Alcohol Wipe Fig. 4 8) Clean top and underside of hood areas adjacent to holes with alcohol wipes. Abrasive Tape 9) Abrasive Tape 9) Wrap abrasive tape over hood lip. Note: To protect vehicle paint from clip, apply tape so that half of tape is on the topside and half is on the underside of hood. 10) Insert screw plugs into 4 previously drilled out holes. 10) Plug 11) Make a small slit (cut) on the rear side of bulb seal at 4 mounting locations. Fig. 5 12) Peel backing off neoprene washers. 13) Fix neoprene washers to clips. 3 of 6 T99D5 9PJ0A II Rev. 05/31/16

4 Inner Clip (A) Fig. 6 14) Slide inner clips (A) onto hood under rubber trim and secure using the large screw through large washer, slit on rubber trim and brackets into previously installed screw plug. Note: Make sure clips are fully seated with no gap to hood edge. Rubber Large Plastic Plug NOT OK OK Fig. 7 15) Slide outer clips (B) onto hood under rubber trim and secure using the large screw through large washer, slit on rubber trim and brackets into previously installed screw plug. Note: Make sure clips are fully seated with no gap to hood edge. Outer Clip (B) Large Plastic Rubber Trim Plug NOT OK OK 4 of 6 T99D5 9PJ0A II Rev. 05/31/16

Fig. 8 16) Insert small screws through fibre washer, loosely secure hood protector to inner clips "A". Note: Do not fully tighten screws. Fig. 9 17) Trim hood paint seal bead.

c) Cut 10mm either side of the locations. Note: Do not cut all the way down to the sheet metal. 18) Clean top and underside of hood areas adjacent to end holes with alcohol wipe.

5 Fig. 8 16) Insert small screws through fibre washer, loosely secure hood protector to inner clips "A". Note: Do not fully tighten screws. Fig. 9 17) Trim hood paint seal bead. a) Pull rubber Hood seal down to prevent cutting. b) Using sharp utility knife, cut thin layer (1~2 mm) of hood paint seal on underside of hood near end holes at metal clip locations. c) Cut 10mm either side of the locations. Note: Do not cut all the way down to the sheet metal. 18) Clean top and underside of hood areas adjacent to end holes with alcohol wipe. Hood Paint Seal Fig ) Wrap abrasive tape over hood lip. Note: To protect vehicle paint from clip, apply tape so that half of tape is on the topside and half is on the underside of hood. 5 of 6 T99D5 9PJ0A II Rev. 05/31/16

12 21) Insert small screws through fibre washer, loosely secure hood

6 NOT OK OK Fig ) Install the wing clips "C" over the abrasive resistant tape strips at the previously marked locations. Note: Make sure clips are fully seated with no gap to hood edge. Fig ) Insert small screws through fibre washer, loosely secure hood protector to outer clips "B" and wing clips "C". Note: Do not fully tighten screws. 22) Check to see that the hood protector is centrally located, adjust as necessary. Fig ) Squeeze hood protector to hood to eliminate any gap while fully tightening each screw. 24) Remove protective blanket and close the hood. 6 of 6 T99D5 9PJ0A II Rev. 05/31/16

INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION:. APPLICATION: 3. PART NUMBER: Hood Protector 004 Nissan Armada 004 Nissan Titan 999D X000 4. KIT CONTENTS: Item No. ) ) 3) 4) ) 6) 7) 8) 9) 0) ) Qty