- PDF Free Download

Size: px

Start display at page:

Download ""

Verity Page
6 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory S P/N 08R04-SWA-100 Application 2010 CR-V Publications No. AII Issue Date AUG 2009 NOTE: Visors may not be legal in all states. Please check the laws of your state 2 Brackets E PARTS LIST Door visor (Front left) 12 Clips Door visor (Front right) Primer Door visor (Rear left) EPT sealer Door visor (Rear right) TOOLS AND SUPPLIES REQUIRED 2 Brackets A 8 Brackets D Shop towel Ruler Felt-tip pen Masking tape Isopropyl alcohol Scissors 2009 American Honda Motor Co., Inc. All Rights Reserved AII (0908) 08R04-SWA of 8

2 Illustration of the Door Visors on the Vehicle RIGHT FRONT RIGHT REAR Installing the Rear Door Visors 1. Fully open the left rear door window. 2. Install two brackets D and one bracket E on the door sash trim in the positions shown. Check the shape of each bracket and install them in the correct positions. Check that the door run channel is installed properly Y INSTALLATION NOTE: These instructions show the left door visors being installed. The same procedure applies to installing the right door visors. Be careful not to damage the paint finish or glass run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. This door visor kit should be installed only if the ambient air temperature is 60 F (15 C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours. 95 mm 120 mm 40 mm Y 2 of 8 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

3 3. Position the left rear door visor on the door sash trim. Adjust the positions of the two brackets D and bracket E, and temporarily install the door visor with the three clips. 4. Attach masking tape to the left rear door visor at both ends of the door visor, then remove the left rear door visor (three clips). 5 mm S S SASH Y Using isopropyl alcohol on a shop towel, clean the door sash trim where the left rear door visor will attach. Apply primer to the areas shown. Wipe up any excess primer immediately. Wait at least 3 minutes or more to cure the primer before proceeding American Honda Motor Co., Inc. All Rights Reserved AII (0908) 3 of 8

4 6. Attach a piece of masking tape to the end of each of the two adhesive backings on the inside of the left rear door visor. Peel back the adhesive backings and tape them to the front surface side of the door visor. Remove all the other remaining adhesive backings. SMALL ADHESIVE BACKING Remove. 8. Reinstall the left rear door visor (three clips). Make sure there is no clearance between the bracket and door sash trim. SMALL ADHESIVE BACKING Remove. 5 mm 3 S 2 ADHESIVE BACKINGS Y 7. Remove the masking tape you attached in step 4. LEFT REAR VISOR Y 4 of 8 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

5 9. Using the palm of your hand, press down on the left rear door visor while removing the two adhesive backings. Make sure there is no clearance between the bracket and door sash trim. ADHESIVE BACKING Press the door visor firmly while removing the adhesive backing. ADHESIVE BACKING Press the door visor firmly while removing the adhesive backing. Installing the Front Door Visors 11. Fully open the left front door window. 12. Install two brackets D on the door sash trim in the positions shown. Check the shape of each bracket and install them in the correct positions. Check that the door run channel is installed properly. Push up. Push up. 90 mm Y 125 mm 10. Repeat steps 1 thru 9 to install the right rear door visor. SASH LEFT FRONT Y 2009 American Honda Motor Co., Inc. All Rights Reserved AII (0908) 5 of 8

6 13. Install bracket A on the door sash trim. 15. Attach masking tape to the door sash at the ends of the left front door visor, then remove the door visor (three clips). 5 mm Y 14. Position the left front door visor on the door sash by hooking the front bracket of the door visor on the door sash. Adjust the positions of bracket A and brackets D and install the three clips. Make sure there is no clearance between the bracket and door sash trim E 16. Using isopropyl alcohol on a shop towel, clean the door sash trim where the left front door visor will attach. Apply primer to the areas shown. Wipe up any excess primer immediately. Wait at least 3 minutes or more to cure the primer before proceeding. 6 of 8 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

7 17. Attach a piece of masking tape to an end of each of the two adhesive backings on the inside of the left front door visor. Peel back the adhesive backings and tape them to the front surface side of the door visor. Remove all the remaining adhesive backings. 19. Reinstall the left front door visor (three clips). Make sure there is no clearance between the bracket and door sash trim. SMALL ADHESIVE BACKING Remove. SMALL ADHESIVE BACKING Remove. 3 S 2 ADHESIVE BACKINGS 18. Remove the masking tape you attached in step LEFT FRONT VISOR American Honda Motor Co., Inc. All Rights Reserved AII (0908) 7 of 8

8 20. Using the palm of your hand, press down on the left front door visor while removing the two adhesive backings. Make sure there is no clearance between the bracket and door sash trim. ADHESIVE BACKING Press the door visor firmly while removing the adhesive backing. ADHESIVE BACKING Press the door visor firmly while removing the adhesive backing. BRACKET USE AND CARE To clean the door visor, wipe it with a soft cloth dampened with clean water. To remove dust and dirt, clean with a soft cloth dampened with a mild detergent and water solution. Never use organic solvents such as thinner, benzine, alcohol, etc., or cleaners containing abrasive compounds. Push up. Push up Y 21. Using scissors, cut the EPT sealer in half. 22. Remove bracket A (one clip). EPT SEALER Cut into two exact halves. EPT SEALER (LEFT SIDE) RIGHT SIDE LEFT SIDE ATTACHING POSITION EPT SEALER (LEFT SIDE) (FRONT LEFT: INNER SIDE) 23. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. 24. Attach the EPT sealer in the area shown, and reinstall the bracket A Repeat steps 11 thru 24 to install the right door visor. 26. Raise and lower all the windows several times to seat the glass run channels. 8 of 8 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 44389 2011 CIVIC S 4- Issue Date AUG 2010 PARTS LIST Left front door visor TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel