GENUINE PARTS INSTALLATION INSTRUCTIONS
|
|
- Gervais Summers
- 5 years ago
- Views:
Transcription
1 GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Front Protector Kit APPLICATION: G Sedan Sports PART NUMBER: K6010-1NH** (XX Designates color) KIT CONTENTS: Item Qty. Description Part Number A 1 Front Chin Spoiler --- B 2 BOLT Square Head --- C 2 Washer(Rubber) AC015 D 2 NUT M6 Hexagon E 4 Push Pin F 1 Paper Template Sheet --- G 1 Installation Instructions --- A B C D E F G TOOLS REQUIRED: Socket & Driver 10mm Clean, Lint-Free Wiping Cloth Masking Tape Phillips head short screwdriver Center Punch 100% Alcohol Clip remover Drill Scissors (3mm (1/8"), 10mm (25/64"), and 8mm (5/16")) Drill Bit PRE-INSTALLATION CAUTIONS/NOTES: CAUTION Install the Front Chin Spoiler when the ambient temperature is above 60 F (15 ). Do not wash or expose the vehicle to a wet environment for 24 hours after installing the Front Chin spoiler. Installing this part concurrently with LED Daytime Driving Lights, please install LED Daytime Driving Lights first then install Front Chin-spoiler. LED Daytime Driving Lights cannot be installed if Front Chin-spoiler is installed first. NOTE These instructions are for the left side of the vehicle; the same procedure applies to the right side. For the right side installation, use templates A and C with the text facing the vehicle. Page 1 of 8 K6010 1NH** II 23/11/16
2 7. INSTALLATION PROCEDURE: Fig 1 1. Installation preparation a) Jack up the vehicle using the instructions under the "Changing a Flat Tire" section of the owner's manual. b) Remove tapping screws(reuse) from under the vehicle. (5 on each side) See Fig. 1. Bottom tapping screw (reuse) Fig 2 c) Fully turn the steering wheel right or left to clear an area and easy to work around the front fender protector.see Fig. 2. Fender protector Fig 3 d) Remove the clip(reuse) that attach the fender protector to the vehicle. (1 on each side) See Fig. 3. Clip (reuse) Template B Template C Fig 4 e) Cut paper templates A, B, and C from paper template sheet F, which is included in installation instruction G. See Fig. 4. Template sheet F Template A Fig 5 bumper edge f) Align template A (RH/LH) to lower front bumper by butting the template. and apply masking tape to hold the template in place. See Fig. 5. Page 2 of 8 K6010 1NH** II 23/11/16
3 Fig 6 g) Align template B (RH/LH) to lower front bumper by butting the template. Align the edge of template B to the alignment line of template A. Apply masking tape to connect template A to template B. See Fig. 6. alignment line alignment line alignment line Fig 7 h) Align template C (RH/LH) to lower front bumper by butting the template. Align the edge of template C to the alignment line of template B. Apply masking tape to connect template B to template C. See Fig. 7. Masking tape Template A Fig 8 Alignment mark for the top of rubber seal i) Use masking tape to make an alignment mark line for the top of the rubber seal by aligning the bottom of a piece of masking tape to the top of template A. See Fig 8. j) Mark the hole position (+) with center punch. See Fig. 6. k) Slowly remove template A,B and C togather (reuse). Center punch Center punch Center punch NOTE: DO NOT REMOVE THE ALIGNMENT LINE MASKING TAPE. BE SURE NOT TO DAMAGE THE TEMPLATE DURING REMOVAL, AS IT WILL BE REQUIRED FOR RIGHT SIDE INSTALLATION. Marking position (bottom view) Fig 9 l) Align template A, B and C to lower front bumper by butting the template. and apply masking tape to hold the template in place. for right hand side. See Fig. 9. bumper edge Page 3 of 8 K6010 1NH** II 23/11/16
4 Approx 10mm Drill bit Fig 10 3mm 10mm (1/8") (5/16") m) Wrap masking tape around 3 mm (1/8"), 8 mm (5/16") and 10 mm (25/64") drill bits, approximately 10mm from the tip. n) Drill 3 mm (1/8") 10 mm (25/64") holes at the marked locations on the front bumper. See Fig 10. Masking tape Fig 11 o) Drill 3 mm (1/8") 8 mm (5/16") holes at the marked locations on the front bumper. See Fig 11. 3mm 8mm (1/8") (5/16") Fig 12 p) Using a clean, lint free cloth and 100% alcohol, wipe any dirt and oil from the mounting surface. Let area dry thoroughly. See Fig. 12. Tape liner Masking tape Tab Part Tape liner Part Fig Front chin spoiler installation exclude part A (see stepc and fig. 13 ) a) At B part of fig.13, Peel off about 30mm of the tape liner from the double-sided tape on the front chin spoiler A. in the direction shown by the arrow. b) At C part of fig.13, Pull tape liner on the front chin spoiler A. Don't peel off the tape liner from the double-sided tape. C) Fold the tape liner onto the front chin spoiler A painted surface and apply masking tape to ensure that the tape liner is accessible. (Total 8 locations) See Fig. 13. Page 4 of 8 K6010 1NH** II 23/11/16
5 Fig 14 d) Assemble squrehead bolt B to Chin spoiler A. See Fig. 14. Square Head Bolt B Retainer Incert square Head bolt to retainer Front chin spoiler A Fig 15 B e) Align the front chin spoiler A Square head bolt B to the drilled holes in the front bumper and push the front chin spoiler A against the front bumper to insert the sqarehead bolt B in the holes. f) Loosely install the nuts C(supplied) and wash D (supplied) on the front chin spoilera squrehead bolt B to ensure that the front chin spoilera is attached. See Fig. 15. WasherD(supplied) Nut C(supplied) Squire head bolt B d e Fig 16 g) Align and adjust the front chin spoiler A to the front bumper to minimize the gap. See Fig 16. Adjust minimize the gap Adjust minimize the gap Front chin spoiler Detail d Front chin spoiler Detail e End rubber Gap Fig 17 End rubber Adjust to remove gap Note: If gap occured between end-rubber and surface of Chin spoiler A. Move Chin spoiler A below from the top and adjust. See fig.17 Page 5 of 8 K6010 1NH** II 23/11/16
6 f Fig18 h) Align top of the front chin spoiler A rubber seal to bottom of the masking tape. See Fig 18. Rubber seal f Masking tape Align to top of rubber seal SEC:f-f g h i k j l Push the bumper Part g and i (SEC:k-k) k l Fig 19 Push the bumper surface lightly Front chin spoiler A Part h and j (SEC:l-l) i) Starting at the center and moving outward, remove the tape liner "g" through "j" and apply at least 15lbs. of pressure to the front chin spoiler A at part of "g" through "k" to ensure that the front chin spoiler A is attached. See Fig. 19. NOTE: REMOVE TAPE LINER SLOWLY, If difficult to remove Tape-liner. Part g and i: Push up protector A lightly from the bottom Part h and j: Push the bumper surface lightly Pull tape liner after enlarging the gap Rubber seal adopted area a a Fig 20 Rubber seal adopted area a a NOTE: If rubber seal came out when pull tape-liner inside out, Please push rubber-seal between and with finger or soft rubber spatulas. See Fig. 20 Rubber seal come out Front bumper Front chin spoiler A SEC:a-a 1Push the bumper surface lightly 2Push rubber seal in the gap between Front protector A and. Page 6 of 8 K6010 1NH** II 23/11/16
7 Fig 21 B j) Tighten nut C(supplied) in area B. See Fig 21. TORQUE VALUE; WasherD(supplied) Front chin spoiler A Nut C(supplied) Squire head bolt B C D Fig 22 k) Install push pin E(supplied) in areas C and D under the vehicle. See Fig. 22. Push pin E E Fig 23 l) Tighten Tapping screw (reuse) in areas E. See Fig 23. TORQUE VALUE; Tapping screw (reuse) Fig 24 m) Install tapping screws(reuse) from under the vehicle. (4 on each side) See Fig. 24. Page 7 of 8 K6010 1NH** II 23/11/16
8 Fender protector Fig 25 n) Install the clip(reuse) that attach the fender protector to the vehicle. (1 on each side) See Fig. 25. Clip (reuse) Page 8 of 8 K6010 1NH** II 23/11/16
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Body Side Molding 2. APPLICATION: Sentra 3. PART NUMBER: 999G2 Lxxxx01 LH (xxxx Designates model year and color) 999G2 Lxxxx02 RH (xxxx Designates
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PRTS INSTLLTION INSTRUCTIONS DESCRIPTION: PPLICTION: PRT NUMBER: KIT CONTENTS: Side Window Deflector Quest (2011) H0800 1J00 Item Qty. 1 B 1 C 1 D 1 E 4 F 4 G 1 Part Description Side Window Deflector
More informationGENUINE MUD FLAP (FRONT)
GENUINE MUD FLAP (FRONT) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, be sure to thoroughly read these instructions. Please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) 2011 CIVIC 4-DOOR All 44416 Issue Date AUG 2010 PARTS LIST Trunk spoiler Right trunk spring (marked red) Left trunk spring
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. 2009 CIVIC HYBRID All 40191 Issue Date AUG 2008 PARTS LIST Rear under spoiler 2 Step bolts 4 Self-tapping screws TOOLS REQUIRED Phillips
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) CIVIC 4-DOOR All 30833 Issue Date SEP 2005 PARTS LIST Trunk spoiler Right trunk spring (marked red) Left trunk spring (marked
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27955 SIDE 2005 CIVIC SI Issue Date AUG 2004 PARTS LIST Left side under spoiler Right side under spoiler 6 Plates 8 Clips Template INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory Application Publications No. 2011 CIVIC AII 44380 S 2-DOOR Issue Date AUG 2010 NOTE: The side under spoilers cannot be installed on a vehicle equipped with splash guards. PARTS LIST
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2013 CIVIC 2-DOOR Publications No. AII 13069 Issue Date NOV 2012 PARTS LIST 4 Flare nuts Left spoiler 2 Washer-nuts Right spoiler 2 Screws 2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 CIVIC 4-DOOR Si Publications No. AII 44423 Issue Date AUG 2010 PARTS LIST Template Front under spoiler TOOLS AND SUPPLIES REQUIRED 4 Self-tapping screws
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: SIDE WINDOW DEFLECTOR Nissan Rogue (2008) 999D3 GX000 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Side
More informationGENUINE REAR SPOILER
GENUINE REAR SPOILER IMPORTANT POINTS IN PAINTING PART NAME: REAR SPOILER PART NUMBER: 0000-8Y-H50/GHK1 V4 920/G44B V4 920 VEHICLE: MAZDA6 1 PAINT AREAS SURFACE TREATMENT a : Paint same as body color b
More informationWheel Arch Trim Set. Installation Manual. This section covers installation of the wheel arch trim set.
Wheel Arch Trim Set FORESTER Wheel Arch Trim Set EN PART # E20SSG000 This section covers installation of the wheel arch trim set. Installation Manual Note: Before performing installation, be sure to read
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS SIDE S 2013 TSX BII 13496 Issue Date SEP 2012 PARTS LIST 4 Screws Left side under spoiler Right side under spoiler 2 Clamps TOOLS AND SUPPLIES
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. FENDER FLARES P/N 08P21-S3V-200 2003 MDX BII 24553 Issue Date SEP 2002 PARTS LIST Right rear fender flare Left front fender flare Right
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping
More informationINSTRUCTIONS Accessory Application Publications No. 2006-2008 CIVIC AII 37696 SIDE 2-DOOR Issue Date AUG 2007 NOTE: Cannot be installed with splash guards. PARTS LIST Left side under spoiler Right side
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REAR SPOILER Application 2011 CR-Z MUGEN Publications No. AII 45919 Issue Date APRIL 2011 PARTS LIST Right wing bracket Rear wing Left wing bracket Right wing base Right
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory Application Publications No. SIDE 2008 CIVIC 4-DOOR All 37741 Issue Date AUG 2007 PARTS LIST Left side under spoiler Right side under spoiler 2 Side lower brackets The side lower
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2006 CIVIC AII 30895 SIDE 2-DOOR Issue Date SEP 2005 PARTS LIST PARTS LIST Left side sticker Left side under spoiler Right side sticker
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS - REAR SPOILER KIT A B C D
GENUINE PARTS INSTALLATION INSTRUCTIONS - REAR SPOILER KIT 1. DESCRIPTION: REAR SPOILER KIT 2. APPLICATION: XGE (C53D) 3. PART NUMBER: K6010-1EA0A 4. KIT CONTENTS: Item QTY Description A 1 Rear spoiler
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2007 CIVIC SI AII 33461 SIDE Issue Date AUG 2006 PARTS LIST Left side under spoiler PARTS LIST Left side sticker (Sold separately) Right
More informationPreparation Part Number: PT Kit Contents Item # Quantity Reqd. Description 1 1 Rear Spoiler 2 1 Hardware Kit. Hardware Bag Contents
Preparation Part Number: PT478-11170-09 Kit Contents 1 1 Rear Spoiler 2 1 Hardware Kit Hardware Bag Contents 1 4 M5 Nut 2 4 Clip 3 4 Hole Plug Additional Items Required For Installation 1 1 Outer Drill
More informationGENUINE REAR SPOILER
GENUINE REAR SPOILER INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents
More informationGENUINE MUD FLAP (REAR)
GENUINE MUD FLAP (REAR) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: Moonroof Wind Deflector Nissan Altima PART NUMBER: 999D UZ000 KIT CONTENTS: Item Qty. Description Service Part Number A B C D E F G H 1
More informationINSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2015 ACCORD 2-DOOR Publications No. VERSION 1 Issue Date AUG 2014 PARTS LIST Template A Right spoiler Left spoiler Template B 2 Rails Right
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory (WITH TEMPLATE) Application 2010 TL Publications No. BII 42533-44799 Issue Date AUG 2010 PARTS LIST Right rear under spoiler 4 Self-tapping screws 10 Seals Left rear
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2012 MDX Publications No. BII 46618 Issue Date OCT 2011 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket
More informationFront aero bumper Lower grille Right air spoiler. Left air spoiler Bolts (15) Self-tapping screws (8)
INSTALLATION INSTRUCTIONS Parts List AERO ACCORD FEB. 2008 Front aero bumper Lower grille Right air spoiler Left air spoiler Bolts (15) Self-tapping screws (8) Nuts (10) Tools and Supplies Required Phillips
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: LED Daytime Driving Lights APPLICATION: ALTIMA SEDAN / COUPE (2010 w/o Foglamp) PART NUMBER: KIT CONTENTS: B66M0 JA00B Installation of this
More informationGENUINE ILLUMINATED SCUFF PLATE
GENUINE ILLUMINATED SCUFF PLATE INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, please thoroughly read these instructions. For
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08P21-STX-200 2008 MDX BII 37680 Issue Date AUG 2007 PARTS LIST Left bracket A Left front fender flare Left bracket B Left front bumper
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 44415 2011 CIVIC 4-DOOR Issue Date AUG 2010 PARTS LIST Trunk spoiler 2 Cap nuts 2 Screws Left trunk spring (marked yellow) Right trunk
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (DECK LID) ACCORD 4-DOOR AII 24063 Issue Date AUG 2002 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring
More informationSide Rocker Installation Instructions
Side Rocker Installation Instructions Guidelines + Trial fit all parts prior to painting + Do not use the side rockers as an attachment point for tie downs + Every 3-6 months, make sure all fasteners are
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 24813 UNDER 2004 TSX Issue Date APRIL 2003 PARTS LIST Rear under spoiler 2 Short step bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 33590 2007 RL Issue Date AUG 2006 PARTS LIST Trunk spoiler Right support strut Left support strut 4 Washer-bolts 4 Adhesive seals TOOLS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24081 ACCORD 2-DOOR Issue Date SEP 2002 PARTS LIST INSTALLATION NOTE: Rear under spoiler Be careful not to damage the rear bumper and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 27035-29095 2005 RL Issue Date MAY 2005 PARTS LIST Trunk spoiler Right support strut Left support strut 4 Washer-bolts 4 Adhesive seals
More informationTrunk spoiler Right torsion bar Template. Trunk spoiler Right torsion bar Template. Clips (4) Double face tapes A (4) Double face tapes B (2)
INSTALLATION INSTRUCTIONS Parts List Trunk Spoiler Kit ACCORD FEB. 2008 Trunk spoiler Right torsion bar Template Clips (4) Trunk Spoiler Kit (PRIMER) Trunk spoiler Right torsion bar Template Clips (4)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) 2005 ACCORD 4-DOOR AII 27503 Issue Date AUG 2004 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SPOILER (LOW) P/N 08F10-TA0-100 Application 2009 ACCORD 4-DOOR Publications No. AII 40062 Issue Date JULY 2008 PARTS LIST Trunk spoiler Right trunk spring (marked red)
More informationRear Side Under Spoiler
00 Rear Side Under Spoiler Installation Manual Genuine part number : E560FL00 Applicable model : IMPREZA 4D (7MY~) - This manual describes how to install and handle the Rear Side Under Spoiler. - Read
More informationGround Effects, P/N: (V6), (V8)
, P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the
More informationQTY 3D PN. FCS PART NUMBER DESCRIPTION
QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691544 A8FOC-17B635-APL FOCUS FRONT AIR DAM 1 691549 A8FOC-17E957-APL FOCUS REAR LOWER 1 691548 A8FOC-10154-APL FOCUS RIGHT SIDE SKIRT 1 691547 A8FOC-10155-APL
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Illuminated Kick Plate APPLICATION: INFINITI M45 (2010) PART NUMBER: G6950-1MA0B KIT CONTENTS: Item QTY Description SERVICE PART NUMBER
More informationINSTALLATION INSTRUCTIONS www.collegehillshonda.com Accessory P/N 08P21-SZA-100 Application 2009 PILOT Publications No. AII 39455 Issue Date MAY 2008 NOTE: The fender trim cannot be installed on vehicles
More informationDouble-check to ensure that all of the parts are included in your shipment. Please immediately contact 3dCarbon if you are missing any part.
5 Pc. Kit Includes QTY 3D PN. DESCRIPTION 1 691815 CRUZE FRONT AIR DAM POLYURETHANE PRE-PRIMERED 1 691816 CRUZE SIDE SKIRT RH POLYURETHANE PRE-PRIMERED 1 691819 CRUZE SIDE SKIRT LH POLYURETHANE PRE-PRIMERED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) ACCORD 4-DOOR AII 30276 Issue Date AUG 2005 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring (marked
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More informationGENUINE Interior Lighting Kit
GENUINE Interior Lighting Kit INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationRev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-10 QTY 3D PART NO. DESCRIPTION 1 691609 FRONT BUMPER REPLACEMENT 1 691610 RIGHT SIDE SKIRT 1 691611 LEFT SIDE SKIRT 1 691612 REAR LOWER SKIRT 4 3M 94 3M ADHESION PROMOTER 16 #8 X ¾ SELF DRILLING
More informationLANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS
LANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS Black with aluminum plate -MZ531356EX Black standard -MZ531357EX
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 37371 SPOILER 2008 TL Issue Date JUN 2007 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Template A TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2012 CIVIC 4-DOOR Publications No. AII 45625-46263 Issue Date MAY 2011 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Template 4 Clip grommets
More informationGENUINE MUD FLAP (FRONT)
GENUINE MUD FLAP (FRONT) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please
More informationDODGE RAM WITHOUT FENDER FLARES FRONT MUD GUARD INSTALLATION INSTRUCTIONS
DODGE RAM WITHOUT FENDER FLARES FRONT MUD GUARD INSTALLATION INSTRUCTIONS PART NO: 5817 Please read instructions thoroughly before installation. Tools Required Short Phillips screwdriver Center punch Drill
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate G CONVERTIBLE G6950 JJ500 Item QTY A 1 B 1 C 1 D 11 E 12 F 9 G 1 Description
More informationM-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS
M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P20-STX-200A Application 2010 MDX Publications No. BII 42020 Issue Date JAN 2010 PARTS LIST Door edge film LF Door edge film RF Door edge film LR Door edge film
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08F02-T0A-100 Application 2015 CR-V Publications No. VERSION 1 Issue Date SEP 2014 PARTS LIST 3 Adhesive sealing washers Tailgate spoiler 2 Hook and loop fasteners
More informationGENUINE REAR MUD FLAP
GENUINE REAR MUD FLAP INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read
More informationGENUINE Interior Lighting Kit
GENUINE Interior Lighting Kit INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationQTY 3D PN. FCS PART NUMBER DESCRIPTION
Rev.05-08 QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691224 A6ZEP-17B635-AAPLN MKZ FRONT AIR DAM 1 691202 A6ZEP-5410154-AAPLN MKZ SIDE SKIRT RH 1 691203 A6ZEP-5410155-AAPLN MKZ SIDE SKIRT LH 1 691225 A6ZEP-17E957-AAPLN
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS
INFINITI GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION:. APPLICATION: Hood Protector Chrome Nissan Armada (004) Nissan Titan (004) 3. PART NUMBER: 4. KIT CONTENTS: Item No. ) ) 3) 4) 5) 6) 7) 8)
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: SIDE WINDOW DEFLECTOR 2. APPLICATION: FRONTIER KING CAB/CREW CAB 3. PART NUMBER: 999D3 BT000KC, 999D3 BT001CC 4. KIT CONTENTS Item No. Qty Description
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory (WING) Application 2010 ACCORD 4-DOOR Publications No. AII 42275 Issue Date AUG 2009 PARTS LIST Trunk spoiler 2 Rubber stops 5 Wire ties with clip A Left trunk spring
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Sedan (2013+) PART NUMBER: 999F4 AX010 - Universal Security Lighting Kit. KIT CONTENTS: Item QTY
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 31129 REARVIEW CAMERA 2006 RL Issue Date OCT 2005 PARTS LIST Attachment Kit P/N: 08B21-SJA-B00 Template Rear camera trim 6-Pin connector
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PRTS INSTLLTION INSTRUCTIONS 1. 2. 3. DESCRIPTION: PPLICTION: PRT NUMER: Radiant Grille Emblem Q60 F2310 5C0K (RGE,W/O CMER,W/O SONR) 4. KIT CONTENTS: Item C Qty. Description Part Number 1 Radiant
More informationQTY 3D PART NO. DESCRIPTION
QTY 3D PART NO. DESCRIPTION 1 691032 V6 FRONT AIR DAM 1 691023 SIDE SKIRT RIGHT 1 691024 SIDE SKIRT LEFT 1 691566 V6 DUAL EXHAUST REAR LOWER SKIRT- 8 3M 94 3M ADHESION PROMOTER 24 #8 X ¾ SELF DRILLING
More informationJK8 Body Kit KIT CONTENTS 1 K
JK8 Body Kit KIT CONTENTS A B C 1 K6861352 D E G F H 2 K6861352 I M N J K L O P Q R S 3 K6861352 T U V W X Y CALL OUT PART NUMBER DESCRIPTION QUANTITY A P5156021 HARDTOP 1 B P5155997 BULKHEAD 1 C 1PH98/9TZZAE
More informationTOYOTA COROLLA HATCHBACK REAR SPOILER Preparation
Preparation Part Number: PT29A-12195-XX Kit Contents 1 1 Rear Spoiler 2 2 Hardware Bag Hardware Bag Contents 1 2 M6 Assembly Nuts 2 2 Grommet Inserts 3 1 Hole Plug Additional Items Required For Installation
More informationTOYOTA RAV DOOR SILL PROTECTORS Preparation
Preparation Part Number: PT747-4230 Kit Contents 2 Front Door Sill Protector 2 2 Rear Door Sill Protector Hardware Bag Contents Additional Items Required For Installation Conflicts Recommended Tools Personal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory DECK LID SPOILER Application 2014 RLX Publications No. BII 13399 Issue Date JAN 2013 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Right trunk spring (marked
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationInstruction No Version Part. No , , , , , , , ,
Instruction No Version Part. No. 30744180 1.2 30794160, 30794013, 30794026, 30794039, 31213192, 30794102, 30794138, 30794151, 30794075 Body kit IMG-256183 Page 1 / 13 Equipment A0000162 A0000163 IMG-239940
More information2015 Mustang Fastback Rear Spoiler Installation Instructions P/N:
Installation Instructions P/N: 421883 421884 421885 421886 421887 421888 421889 421890 421891 421892 421893 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015 Mustang Fastback Rear Spoiler Installation
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. DESCRIPTION: APPLICATION: PART NUMBER: Accent light Kit Cube (MY2013+) 999F3 AW000 - Universal Accent Lighting Kit. 4. KIT CONTENTS: Item QTY Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 30250 UNDER SPOILER 2006 RSX Issue Date JULY 2005 PARTS LIST Rear under spoiler 5 Stepped bolts 2 Bolts 7 Flange nuts, 6 mm 3 Square
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 3RD ROW P/N 08R12-SHJ-100 2006 ODYSSEY AII 30563-31117 Issue Date OCT 2005 PARTS LIST Left side rear sunshade Driver s Side 1. Remove the
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 CR-V Publications No. AII 42587 Issue Date AUG 2009 PARTS LIST HFL Attachment Kit P/N 08E02-SWA-130 (Ivory) P/N 08E02-SWA-170
More informationToyota Venza Interior Light Upgrade
Toyota Venza 2011 - Interior Light Upgrade Part Number 00016-00095 Accesory Code: IL2 Conflicts Kit Contents Item # Quantity Reqd. Description 1 1 Y Adapter 2 1 Wire harness 3 1 Hardware Kit 4 2 White
More informationGENUINE MUD FLAP (FRONT)
GENUINE MUD FLAP (FRONT) INSTALLATION INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, Please thoroughly read these instructions. For your safety, please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 28593 2006 RIDGELINE P/N 08F23-SJC-100 Issue Date FEB 2005 PARTS LIST Center front bumper trim (Not used if the vehicle is equipped
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More informationGENUINE FOG LAMP KIT
GENUINE FOG LAMP KIT Using (Installation) Instructions Applicable model : MAZDA CX-7 Part Number : ER18 V4 600 (small tank) ER19 V4 600 (large tank) Thank you very much for buying the Mazda Genuine Parts.
More informationVehicle and all installation material temperatures must be within the following range before and during installation: 60 F [15 C] and 100 F [43 C].
INSTALLATION INSTRUCTIONS DESCRIPTION: BODY SIDE MOLDING KIT, DEALER Vehicle and all installation material temperatures must be within the following range before and during installation: 60 F [15 C] and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 37518 2008 RDX Issue Date JUL 2007 PARTS LIST 10 Plain washers, 12 mm Trailer Hitch Kit P/N 08L92-STK-200 Trailer hitch 6 Lock washers,
More informationAggressive Chin Spoiler CDC#
Note: 2005-2009 Aggressive Chin Spoiler CDC# 110021 Read installation instructions before starting and test fit component before painting. Chin Spoiler is a molded Urethane part. To ensure the quality
More information