Small I/O connectors for AC adapters

Transcription

1 Small I/O connectors for C adapters RP34 Series Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. Product Specifications Ratings Features 1. Superior mating operability snap-and-lock style allows easy mating/ unmating. 2. Cable direction is variable The three-position, right-angled plug makes it possible to arrange the cable to the left or right, offering flexible wiring options depending on your requirement. 3. Sequential contact mating Designed with sequential contact mating, one pin makes contact with its counterpart sooner than the others and establishes a securely grounded connection. 4. Easy plug assembly snap-together case eliminates the need for screws to fasten the case and helps provide for a quick plug assembly. 5. Variations Items Number of contacts 3 or, 4 Connector type Plug : Straight, right angle Receptacle : Right angle Plug termination version Crimp Receptacle termination version PCB dip Receptacle mounting method PCB dip Rated current 3 Operating temperature range -1 to +6 Rated voltage C3V, DC42V Storage temperature range -1 to +6 Items Specifi cations Conditions 1. Contact resistance 3mø max Measured at DC 1 2. Insulation resistance 1,Mø min Measured at DC 1V 3. Withstanding voltage No flashover or dielectric breakdown. C 15V for 1 minute 4. Vibration 1 to 55Hz/cycle, amplitude :.75mm, 3 axis directions, No electrical discontinuity for 1µs or longer. resistance 2 hours each 5. Shock resistance No electrical discontinuity for 1µs or longer. cceleration : 49m/s 2, duration : 11ms, 3 axis directions, 3 cycles each 6. Mating Cycles Contact resistance : 6mø max. 1, times -55ç : 3 minutes Normal temperature : 1 to Temperature cycle Insulation resistance : 1Mø min. minutes 85ç : 3 minutes Normal Temperature : 1 to 15 minutes, left for 5 cycles 8. Moisture resistance Insulation resistance: 1Mø min (at high humidities). 1Mø min (when dry). Temperature : 4ç, relative humidity : 9 to 95%, left for 96 hours Materials / Finish Items Material Finish Remarks Exterior, insulator Polycarbonate resin UL94V- Plug Clamp Brass Bushing Vinyl chloride resin PBT resin UL94V- Exterior, insulator Receptacle Steel Tin plating Male contact Brass Silver plating Crimped female contact Female contact Phosphor bronze Silver plating In cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information w 1

2 RP34 Series Small plastic connectors for C adapters Product Number Structure Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders. Connector RP34-8 SP - 3 S C (71) Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. Model name : RP34 Series Shell size : The shell size is the outer diameter of the mating end of the plug. Shell type SP : Straight plug P : Right-angled plug R : Receptacle Number of contacts : Contact form P : Male contact S : Female contact Contact termination method : C : Crimp contact termination DL : Right-angled dip method Other specifi cations : two-digit character is added to indicate other specifi cations. Crimp contact RP34 - SC Model name : RP34 Series Contact type : SC = Crimped female contact Contact packaging types : 1 : Loose piece contacts 2 : Reel contacts pplicable wire : 1 : For 18 to 22 WG 2 : For 24 to 28 WG Identifi cation of plating : 2 : Silver plating 2

3 1 RP34 Series Small plastic connectors for C adapters Straight plug Ø RP34-8SP-3SC(71) (This fi gure is a representative example.) Part No. HRS No. No. of contacts Remarks RP34-8SP-3SC(71) RP34-8SP-3SCD(71) Mating key dependent type RP34-8SP-4SC(71) Note : Cable clamping force, cable rotation force, and other aspects may differ depending on the cable construction. We reccomend that you verify the suitability of the cable assembly before use or production. Right-angled plug RP34-8P-3SC(71) Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved Ø4.4 (This figure is a representative example.) Part No. HRS No. RP34-8P-3SC(71) Note : Cable clamping force, cable rotation force, and other aspects may differ depending on the cable construction. We recommend that you verify the suitability of the cable assembly before use or production. 3

4 RP34 Series Small plastic connectors for C adapters Receptacle B Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. (This figure is a representative example.) Part No. HRS No. No. of contacts B Remarks RP34-8R-3PDL RP34-8R-3PDLD Mating key dependent type RP34-8R-4PDL Ø1.7 3 position Positioning hole (1 location) Ø1.5 RP34-8R-3PDL Contact (female contact) Dip post arrangement for PCB layout 3-Ø C 1.5 _ B Part No. HRS No. B C pplicable wire size Remarks RP34-SC to 22 WG Reel contacts Loose piece RP34-SC to 22 WG contacts RP34-SC to 28 WG Reel contacts Loose piece RP34-SC to 28 WG contacts Note : Loose piece contacts are packaged 1 pcs/pack and reel contacts are available on 1, piece reel. Please order in full quantity packs or reels. Positioning hole (1 location) Ø Ø1.1 4 position Ø Remarks 1. The applicable PCB thickness is between.8 and 1.6mm. 2. machining tolerance of ±.5 is recommended for the PCB layout. 3. The above fi gure shows the PCB side of the rack into which contact dip posts will be inserted. " " mark indicates the plug interface mating side. 4

5 1.3 RP34 Series Small plastic connectors for C adapters Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. Termination procedure Straight plug Cable Bushing Metal fitting for clamping Cord tube () or (B) S-insulation P case Rightangle plug Cover S-insulation P case Cord tube pplicable tools mm or more Operation procedure straight plug 1. First, pass the prepared cable through the bushing, and then crimp and terminate the contacts. 2. ssemble the crimped and terminated contacts into the contact holes of the S-insulation P case. t this time, please make sure that the crimped contacts are securely engaged onto the contact holes of the S-insulation P case by lightly pulling on the cable. 3. Crimp and fi x the metal fi tting for clamping with the applicable tool (RP34-TC-1). 4. ssemble the S-insulation P case, metal fi tting for clamping, and bushing onto the cord tube (). The S-insulation P case can be assembled in two ways, at 18 opposing angles. Please make sure to select the orientation that is suitable for your purpose. 5. Finally, assemble the remaining cord tube (B). The assembly has been completed. Operation procedure right-angled plug 1. The right-angled plugs can be assembled in the same manner as the straight plugs, and the S-insulation P case can be assembled to the cord tube in one of two positions. 18 opposite each other. Please make sure to select the orientation that is suitable for your purpose. Type Items Part No. HRS No. pplicable contact pplicable wire size utomatic crimping press CM-15C Machine P15-RP RP34-SC to 22 WG crimping pplicator P15-RP RP34-SC to 28 WG Cable crimping tool RP34-TC Extraction tool RP34-SC-TP Cable crimping tool (RP34-TC-1) (The handle shape shown above is a representative example.) utomatic crimping press (Type CM-15C) 5

6 RP34L Series Small plastic connectors for C adapters Type RP34L Product Specifications Rated current 5 (when using 18 WG) Operating temperature range 25 to +85 Ratings Rated voltage C3V, DC42V Storage temperature range 1 to +6 Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. Items Specifi cations Conditions 1. Contact resistance 3mø max. Measured at DC 1 2. Insulation resistance 1,Mø min. Measured at DC 1V 3. Withstanding voltage No fl ashover or dielectric breakdown. C 15V for 1 minute 4. Vibration proof No electrical discontinuity 1µs or longer. 1 to 55Hz, half amplitude :.75mm, 3 axis directions, 2 hours each -55ç : 3 minutes Normal temperature : 1 to Temperature cycle Insulation resistance : 1Mø min minutes +85ç : 3 minutes Normal Temperature : 1 to 15 minutes, 5 cycles 6. Corrosion resistance No corrosion that affects performance. Left in 5% salt water solution for 48 hours 7. Mating Cycles Contact resistance : 6mø max 5, times Materials / Finish Receptacle (2position) Plug (2 position) Receptacle (3 position) Plug (3 position) Items Material Finish Remarks Metal fi tting Phosphor bronze Solder plating Insulator Polyamide resin Black UL94HB Contact Brass Palladium plating Exterior Vinyl chloride resin UL94V- Black Insulator Polyamide resin UL94HB Contact Phosphor bronze Silver plating Metal fi tting Phosphor bronze Solder plating Insulator PPS resin Black UL94V- Contact Brass Palladium plating Exterior Polycarbonate resin Vinyl chloride resin Black UL94V- Insulator PPS resin Contact Phosphor bronze Palladium plating Product Number Structure Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders. RP34L - 5P- 2SC(****) Series name : RP34L Shell : Indicates the shell form. Type Receptacle : R Straight plug : P Right-angled plug : LP Number of contacts : Shows the number. 2 or 3 contacts. Contact type PD : Male contact (dip) SC : Female contact (crimped) Cable length : (****) may vary depending on the cable. 6

7 RP34L Series Small plastic connectors for C adapters Receptacle 2 position 2 position 3 position Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved RP34L-5R-2PD(71) 3 position RP34L-5R-3PD(71) Part No. HRS No. RP34L-5R-2PD(71) RP34L-5R-3PD(71) Plug RP34L-5P-2SC(1857)(71) Recommended panel opening dimensions (reference) Panel (1.2) PCB PCB layout dimension 3.45± ±.5 (Mating interface side) 2 Ø Ø ± ± _ ±.5 3 4±.5 Recommended panel opening dimensions (reference) Plug PCB Panel PCB layout mounting dimensions 4.3±.5 4.3±.5 (Mating interface side) 2 Ø Board-in crimping contact Ø3.5 4 Ø ± ±.5 Bushing Single-contact shielded cable (Center conductor wires: 18 WG, shielded cable: 18WG or equivalent) R3 Ø ±.5 (1.2) 4± ± ±.5 (External shell) Ø RP34L-5P-3SC(71) Ø Part No. HRS No. RP34L-5P-2SC(1857)(71) RP34L-5LP-3SC(71) 7.8 RP34L-5P-3SC(71) RP34L-5LP-3SC(71)

8 RP34L Series Small plastic connectors for C adapters Crimp contact Section _ 2.2 RP34L-SC1-212(1) Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. Part No. HRS No. RP34L-SC1-212(1) pplicable tools Type Part No. HRS No. pplicable contact pplicable cables Manual crimping tools HT-12/RP34L-SC RP34L-SC1-112(1) 18 to 22 WG utomatic Machine CM-15C crimping press crimping pplicator P15-RP34L-SC RP34L-SC1-212(1) 18 to 22 WG Cable crimping tool RP34-TC Ø4 Extraction tool RP6-SC-TP ssembly procedure (3 position plug) Straight plug 1 (Mating section) Cord tube () S-insulation P case Right angle Cable Bushing Metal fitting for clamping (Round hole) Cord tube (B) Cord tube () 13.7 (Tab) Cord tube (B) First pass the prepared cable through the bushing, and then crimp and terminate the contacts. 2. ssemble the crimped and terminated contacts into the contact holes of the S-insulation P case. t this time, please make sure that the crimped contacts are securely engaged onto the contact holes of the S-insulation P case by lightly pulling the cable. If you find an erroneous wiring, insert the extractor (RP6-SC-TP) from the mating side to pull out the contact from the termination side, and then reassemble. 3. Crimp the metal fi tting for clamping with the applicable tool (RP34- TC-1). 4. lign and assemble the protrusion of the S-insulation P case to the round hole of the cord tube (B). 5. ttach the mating section of the metal fitting for clamping to the recess of the cord tube (B), and then assemble the bushing and metal fi tting for clamping onto the cord tube (B). 6. ssemble the cord tube () onto the cord tube (B). t this time, please make sure that the four tabs of the cord tube (B) rest on the angled hole of the cord tube (). 1. Right-angled plugs can be assembled in the same manner as the straight plugs. S-insulation P case Metal fitting for clamping 2 11 Bushing 2 Cord tube Cable Metal fitting for clamping S-insulation P case 1 8

9 RP34L Series Small plastic connectors for C adapters Precautions 1. To prevent damage to the connector after mounting, make sure that it is supported with a panel or another substrate. This will prevent any type of excessive load or force on the connector. For 2 position type, please support the external shell of the receptacle. For 3 position type, please support the external shell of the plug. See page 3 for details on recommended panel dimensions. Receptacle (External shell) Receptacle Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. Panel 2. When mated together, do not apply a load of 3 N or more on the cable in the direction indicated by the arrows. Please note that an excessive tensile stress may break the connectors. Plug <2 position type> <3 position type> 3. This product series uses silver plated contacts. Silver reacts easily to exposure to sulfur gas so the below conditions may cause tarnishing. Dusty environments rea with a high concentration area of gases such as sulfur dioxide gas, hydrogen sulfide gas, nitrogen dioxide gas and so on. Example; In close proximity to factory exhaust, automotive emissions, etc. Close to heaters, or in other areas marked by extreme temperature differences or high humidity. Close to rubber products includes rubber adhesives. The Electrical connection is not affected by tarnishing on a silver surface due to the wiping effect of the contact pins. Panel Storage Packing state; Packed in original packing or equivalent container Temperature -1 to +6ç Humidity 85% Max (It is recommended that the product be stored in an area of normal level of temperature and humidity, and free of any temperature fluctuation) Please use this products within 6 months of delivery. (fter 6 month, please check the solderbility before use) Storage means long-term storage of the unused products in sealed packaging, prior to assembly to PCB. 9

10 RP34 Series Small plastic connectors for C adapters MEMO : Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. 1

11 RP34 Series Small plastic connectors for C adapters MEMO : Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. 11

12 Powered by TCPDF ( RP34 Series Small plastic connectors for C adapters US: HIROSE ELECTRIC (U.S..), INC. HEDQURTERS CHICGO OFFICE 23 Warrenville Road, Suite 15, Downers Grove, IL 6515 Phone : US: HIROSE ELECTRIC (U.S..), INC. SN JOSE OFFICE 2841 Junction ve, Suite 2 San Jose, C Phone : Fax : US: HIROSE ELECTRIC (U.S..), INC. DETROIT OFFICE (UTOMOTIVE) N. Laurel Park Drive, Suite 253, Livonia, MI Phone : Fax : Sep Copyright 218 HIROSE ELECTRIC CO., LTD. ll Rights Reserved. US: HIROSE ELECTRIC (U.S..), INC. BOSTON OFFICE 3 Brickstone Square Suite 21, ndover, M 181 Phone : GERMNY: HIROSE ELECTRIC EUROPE B.V. NUREMBERG OFFICE Neumeyerstrasse 22-26, 9411 Nurnberg Phone : Fax : UNITED KINGDOM: HIROSE ELECTRIC EUROPE BV (UK BRNCH) 4 Newton Court, Kelvin Drive, Knowlhill, Milton Keynes, MK5 8NH Phone : Fax : CHIN: HIROSE ELECTRIC (CHIN) CO., LTD. SHENZHEN BRNCH Room 9-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre, 52 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 5188 Phone : Fax : KORE: HIROSE KORE CO.,LTD. 143, Gongdan 1-daero, Siheung-si, Gyeonggi-do, 1584, Korea Phone : Fax : THE NETHERLNDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 111 CC msterdam Z-O Phone : Fax : GERMNY: HIROSE ELECTRIC EUROPE B.V. HNOVER OFFICE Bayernstr. 3, Haus C 3855 Langenhagen, Germany Phone : Fax : CHIN: HIROSE ELECTRIC (CHIN) CO., LTD. (SHNGHI, HEDQURTERS) 18, Enterprise Center Tower 2, 29# Gong He Road, Jing an District, Shanghai, CHIN 27 Phone : Fax : HONG KONG: HIROSE ELECTRIC HONGKONG TRDING CO., LTD. Room 11, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : Fax : SINGPORE: HIROSE ELECTRIC SINGPORE PTE. LTD. 3, nson Road, #2-1, Springleaf Tower, Singapore 7999 Phone : Fax : GERMNY: HIROSE ELECTRIC EUROPE B.V. GERMN BRNCH Schoenbergstr. 2, 7376 ostfildern Phone : Fax : FRNCE: HIROSE ELECTRIC EUROPE B.V. PRIS OFFICE 13 venue Joseph Kessel, Bat E, 7896 Voisins le Bretonneux, France Phone : Fax : CHIN: HIROSE ELECTRIC (CHIN) CO.,LTD. BEIJING BRNCH 11, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 125 Phone : Fax : TIWN: HIROSE ELECTRIC TIWN CO., LTD. 13 8F, No.87, Zhengzhou Rd., Taipei Phone : Fax : INDI: HIROSE ELECTRIC SINGPORE PTE. LTD. DELHI LIISON OFFICE Office NO.552, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9, Block B, Noida, 2131, Uttar Pradesh, India Phone : Fax : INDI: HIROSE ELECTRIC SINGPORE PTE. LTD. BNGLORE LIISON OFFICE Unit No-43, 4th Floor, No-84, Barton Centre, Mahatma Gandhi (MG) Road, Bangalore 56 1, Karnataka, India Phone : Fax : MLYSI: PENNG REPRESENTTIVE OFFICE , Ideal@The One, Jalan Mahsuri, Bayan Lepas Penang, 1195, Malaysia Phone : THILND: BNGKOK OFFICE (REPRESENTTIVE OFFICE) Unit 473, 47th FL., 1 Empire Tower, South Sathorn Road, Yannawa, Sathorn, Bangkok 112 Thailand Phone : Fax : ,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi ,JPN TEL: Fax: The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 7/218. Contents are subject to change without notice for the purpose of improvements.